GE TPG24BRDBS Mode d'emploi

Marque: GE

Modèle: TPG24BRDBS

Catégorie: Frigos

Taper: Mode d'emploi

Use and Care Guide
Refrigerator—Freezer
G-Line Large Side by Side 
and Built-In Style
English Version ................................. 2
Version française ......................... 27
Versión en español  .................... 53
Safety Instructions ....................... 2
Operating Instructions, Tips
Automatic Icemaker .................................... 7
Electronic Monitor  ........................................ 5, 6
Ice and Water Dispenser ............................ 8
Refreshment Center ..................................... 4
Refrigerator Doors ........................................ 3
Shelves .................................................. 10, 11
Storage Drawers ........................................... 9
Temperature Controls  ................................. 3
Care and Cleaning
Behind Refrigerator  ................................... 13
Cleaning—Inside and Outside  ................. 12
Cleaning the Decorator Door Panels .... 12
Drawer and Cover Removal  .................... 13
Light Bulb Replacement ........................... 13
Under Refrigerator ..................................... 13
Problem Solver ..................... 23–26
Normal Operating Sounds  ................... 23
Preparation
Clearances ................................................... 14
Dimensions .................................................. 14
Dimensions and Specifications 
for Built-In Style Models .........................15
Leveling Rollers/Door Alignment .......... 15
Location ........................................................ 14
Moving and Vacation ................................ 14
Trim Kits ................................................ 16–18
Water Supply to Icemaker  ....................... 14
Installation ................................ 19–22
Earthing ........................................................ 19
Electrical Requirements .................... 19, 20
Fitting a Different Plug .............................. 20
Great Britain and Ireland  .......................... 20
How to Install Features ............................. 21
Additional Features ................................ 22
Mains Lead Replacement ................... 2, 20
Model and Serial Numbers ........................ 2

HELP US HELP YOU…

Read this guide carefully.

It is intended to help you operate and maintain your new

refrigerator properly.

Keep it handy for answers to your questions.

If you received a damaged refrigerator…

Immediately contact the dealer (or builder) that sold you the refrigerator.

Save time and money. Before you request service…

Check the Problem Solver in the back of this guide. It lists minor

operating problems that you can correct yourself.

Products are continuously being improved…

Therefore product features and specifications may change or

vary slightly.

Write down the model and serial numbers.

You’ll see them on a label inside the fresh food compartment

on the top.

Please write these numbers here:

Model Number

Serial Number

Use these numbers in any correspondence or service calls concerning

your refrigerator.

WARNING—When using this appliance, always

exercise basic safety precautions, including the

following:

• Use this appliance only for its intended purpose as

described in this Use and Care Guide.

• This refrigerator must be properly installed

and located in accordance with the

Installation Instructions before it is used.

WARNING—Connect to potable water supply

only.

• Never unplug your refrigerator by pulling on the

power cord. Always grip plug firmly and pull straight

out from the outlet.

• Repair or replace immediately all electric service

cords that have become frayed or otherwise

damaged. Do not use a cord that shows cracks or

abrasion damage along its length or at either the plug or

appliance end.

• When moving your appliance away from the wall, be

careful not to roll over or damage the power cord.

• Do not allow children to climb, stand or hang on the

shelves in the refrigerator. They could damage the

refrigerator and seriously injure themselves.

• If your old refrigerator is still around the

house but not in use, be sure to remove the

doors. This will reduce the possibility of danger

to children.

• After your refrigerator is in operation, do not touch

the cold surfaces in the freezer compartment,

particularly when hands are damp or wet. Skin may

adhere to these extremely cold surfaces.

• Do not place fingers or hands on the automatic ice-

making mechanism while the refrigerator is plugged

in. This will prevent contact with the moving parts of the

ejector mechanism, or with the heating element that

releases the cubes.

• Do not allow anyone to climb, sit, stand or hang on the

Refreshment Center Compartment door. They could

damage the refrigerator and maybe even tip it over,

causing severe personal injury.

• Unplug your refrigerator before cleaning and making

repairs. NOTE: We strongly recommend that any

servicing be performed by a qualified individual.

• Before replacing a burned-out light bulb, unplug the

refrigerator or turn off power at the circuit breaker or

fuse box in order to avoid contact with a live wire

filament. (A burned-out light bulb may break when

being replaced.) NOTE: Turning control to

“ ”

position does not remove power to the light circuit.

• Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other

appliance.

Mains lead replacement

If the mains lead on your refrigerator needs replacing at

any time, it must be replaced by a special lead which is

obtainable from your local dealer. A charge will be made

for the replacement of the mains lead if you have damaged

the lead.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

Read all instructions before using this appliance.

OPERATING YOUR REFRIGERATOR

Set the Temperature Controls (appearance may vary)

Two controls let you regulate the temperature in the fresh food and

freezer compartments.

At first, set both the fresh food control and the freezer control to “5.”

Allow 24 hours for the temperature to stabilize, whether you are

setting the controls for the first time or adjusting them later. Then, if

you want colder or warmer temperatures in either compartment, adjust

the controls one step at a time.

NOTE: Moving the freezer control to the

“ ”

position turns off

cooling in both compartments—fresh food and freezer—but does not

shut off power to the refrigerator.

3 5

Ambient Room Temperature Limits How to Test Temperatures

This refrigerator is designed to operate in ambient temperatures

specified by its Temperature Class which is marked on the rating plate.

Temperature Symbol Ambient Temperature

Class

Maximum Minimum

Extended-

Temperate SN 32°C 10°C

Temperate N 32°C 16°C

Subtropical ST 38°C 18°C

Tropical T 43°C 18°C

NOTE: Internal temperature may be affected by such factors as the

location of the refrigerator, ambient temperature and frequency of

door openings. Adjust temperature controls as required to compensate

for these factors.

Use the milk test for the fresh food compartment. Place a container

of milk on the top shelf in the fresh food compartment. Check it a day

later. If the milk is too warm or too cold, adjust the temperature controls.

Use the ice cream test for the freezer compartment. Place a

container of ice cream in the center of the freezer compartment. Check

it after a day. If it’s too hard or too soft, adjust the temperature controls.

Always allow 24 hours for the refrigerator to reach the

temperature you set.

Important Safety Instructions Operating Your Refrigerator

Refrigerator Doors

The refrigerator doors may feel different than the ones you are used to.

The special door opening/closing feature makes sure the doors close

all the way and are securely sealed.

When opening and closing the door you will notice a “stop” position.

If the door is opened past this “stop” point, the door will remain open

to allow you to load and unload food more easily. When the door is

only partially open it will automatically close.

The resistance you feel at the “stop” position will be reduced as the

door is loaded with food.

When the door is only

partially open it will

automatically close.

Beyond this “stop” the

door will stay open.

Refrigerator

control

Freezer

control

REFRESHMENT CENTER

(on some models)

Refreshment Center Compartment

The Refreshment Center Compartment stores frequently used items.

When open, the Refreshment

Center door provides a

convenient work surface.

Although durable, the work

surface should not be used as a

cutting board. Close the door

when finished. The upper fresh

food compartment light will

come on when the Refreshment

Center door is opened.

The special design of the door

allows you to tilt and lift up the

entire door in order to clean the

bottom of the frame.

NOTE: Use caution in closing or

using the clean-out feature in the

presence of small children.

Cold air entering from the freezer

compartment keeps the temperature

in the Refreshment Center

Compartment at proper food-

keeping levels.

The bin panel limits the amount

of cold air that escapes when the

Refreshment Center door is opened.

To reach food from the inside, lift

the panel up.

To remove the Refreshment Center bin,

first remove the panel using the hand holds.

Then remove the bin by lifting it up

and out.

Bottom of

Frame

ELECTRONIC MONITOR

(on some models)

➀Flashes when either door is open.

➁When lit, the Door Alarm beeper is set to sound after either door

has been open 30 seconds.

➂Lights up when freezer food-keeping temperature is above normal.

➃Lights up to indicate that no failure has been detected by the

diagnostic system.

➄Flashing diagnostic codes.

Check your frozen food. Has any of it started to thaw?

A package may be holding the freezer compartment door

open. Don’t open the door more often than absolutely

necessary while this code is displayed. Touching the

pad after the freezer compartment temperature has

returned to normal will erase the code.

Power to the refrigerator has been interrupted for

more than two seconds. Check the condition of food in

both the fresh food and freezer compartments. Touch the

pad to erase code.

There is no fault with the refrigerator when the

code flashes.

Check the icemaker. Ice clumps in the storage bin may

have stalled the icemaker. Follow corrective measures

described in the Problem Solver section. If water supply

to the icemaker is not connected or not turned on, make

sure manual icemaker switch is in the (up) position.

This code stops flashing when problem is corrected

or the pad is touched.

Something is wrong with the defrost system—keep

doors closed to retain cold and call for service. The

code flashes until problem is corrected.

➅Reviews the four coded functions and allows you to erase codes

from the display.

➆

chilled water, ice cubes or crushed ice.

3 5

When Your Refrigerator Is First Plugged In

All panel lights come on for five seconds, a beep sounds, and lights go

off except as follows:

• PF flashes in the display. Touch this pad to erase it.

• This pad glows.

• The Warm Temperature light glows if the freezer

compartment temperature is higher than normal.

It goes off when proper food-keeping temperature

is reached.

• The Door Alarm beeper is activated and the Door

Alarm pad glows.

• The Crushed Ice pad glows.

• This pad flashes if either door is open, goes out

when doors are shut.

• The night light in the ice and water dispenser is off.

(continued next page)

Refreshment Center Electronic Monitor

How the System Works

ELECTRONIC MONITOR

(continued)

The system alerts you when something starts to go wrong.

If a diagnostic code appears on the display, something needs

special attention. The display code flashes until you erase it. The first

6 flashes are accompanied by beeps.

If more than one coded function requires attention at the same

time, the most important one will be displayed first.

This pad evaluates all other coded functions. If the

display is lit during the displaying of a code, that

function is operating properly. This pad is lighted

except when a failure has been detected.

This pad has two functions:

1. It reviews the diagnostic codes.

2. It erases two codes—

PF and CI. The dE and FF

codes can only be erased after the condition that

caused the code to flash has been corrected.

How to Set the Door Alarm Why the Warm Temperature Light Glows

You don’t have to set the visual alarm.

As long as either door is open, this pad flashes.

When the Door Alarm pad is glowing, the beeper

alarm is set. Touch the pad to turn it on or off.

If either door is open for more than 30 seconds, the

control beeps.

The light goes out and the beeping stops when you close the door.

At first, it’s probably because your newly installed

refrigerator hasn’t completely cooled down yet. Wait

a few hours for it to cool, and then the light will go out.

From then on, the pad will glow whenever

temperatures inside get too high for proper food

storage. If this happens, open the doors only when

absolutely necessary, and close them as quickly as possible.

As soon as inside temperatures return to normal, the light goes out.

If the Warm Temperature light reappears and stays on for longer than

4 hours, call for service.

Electronic Monitor Automatic Icemaker

AUTOMATIC ICEMAKER

How The Icemaker Works

Your icemaker will produce 8 cubes per cycle—approximately

120 cubes in a 24-hour period—depending on freezer compartment

temperature, room temperature, number of door openings and other

use conditions.

If you use your refrigerator before the water connection is made,

make sure the icemaker feeler arm is in the (up) position. When the

water supply has been connected to the icemaker, move the feeler arm

to (down) position.

The icemaker will fill with water when it cools to freezing.

NOTE: With a newly-installed refrigerator, allow about 24 hours

for the freezer compartment to get cold enough to make ice.

Throw away the first few batches of ice cubes (16 or 24 cubes). This

will flush away any impurities in the water line. Do the same thing

after vacations or extended periods when ice isn’t used.

To make sure the bin fills with ice, level the cubes occasionally.

When cubes fall into the bin they may pile up close to the icemaker

and push the feeler arm to the (up) position before the bin gets

full. Keeping the cubes level allows the icemaker to fill the bin.

The icemaker ejects cubes in groups of 8, and it is normal for several

cubes to be joined together.

Move Feeler Arm to (up) Position When…

• Home water supply is to be turned off for several hours.

• Ice storage bin is to be removed for a period of time.

• Going away on vacation, at which time you should also turn off the

valve in the water supply line to your refrigerator.

• Moving the freezer control to the

“ ”

position.

If This Is Your First Icemaker…

You’ll hear occasional sounds that may be unfamiliar. These are

normal icemaking sounds and are not cause for concern.

If Ice Is Not Used Often…

‘‘Old’’ ice cubes will become cloudy and taste stale. Empty ice

storage bin periodically and wash it in lukewarm water. Be sure to

allow storage bin to cool before replacing it—otherwise ice cubes

may stick to other parts of the icemaker.

A newly-installed refrigerator may take

up to 24 hours to begin making ice.

Feeler arm in

(up) position

stops icemaking

Feeler arm in

(down) position

begins icemaking

ICE AND WATER DISPENSER

To Dispense Ice and Water

• Select:

water (on some models),

ice cubes,

or crushed ice (on some

models).

• Grip the glass or other container near the rim and press the rim

against the center of the pad.

• After crushed ice is dispensed, some water may drip from the chute.

The spill shelf is not self-draining. The shelf and its grille should be

cleaned regularly according to the Care and Cleaning instructions.

WATER CRUSHED CUBEDICE

LIGHT

OFF ON

Crushed Ice Water

• Some crushed ice may be dispensed even though you selected .

This happens occasionally when a few cubes get channeled to the

crusher.

• Sometimes a mound of snow will form on the door in the ice chute.

This condition is normal, and usually occurs when you have

dispensed crushed ice repeatedly. The snow will eventually

evaporate.

• Sometimes crushed ice will spray beyond the glass. To avoid this,

hold the glass up close to the chute.

• On models with a water dispenser, if no water is dispensed when the

refrigerator is first installed, there may be air in the water line

system. Press the dispenser pad for at least two minutes to remove

trapped air from the water line and to fill the water system.

• The first glass of water dispensed may be warmer than the following

ones. This is normal.

• Dispensed water is cool, not iced. For colder water, simply add

crushed ice or cubes before dispensing water.

CAUTION: Never put fingers or other objects into the

dispenser opening.

To Remove Ice Storage Bin To Replace Ice Storage Bin

Lift the left corner to free the bin from

the shelf. Pull the bin straight out while

supporting it at front and back.

Slide the bin back until the tab on the

bin locks into the slot in the shelf.

If the bin does not go all the way back,

remove it and turn the drive mechanism

1/4 turn. Then push the bin back again

until the tab on the bin locks into the

slot in the shelf.

Important Facts About Your Dispenser

• If this is your first icemaker you’ll hear occasional sounds that

may be unfamiliar. These are normal icemaking sounds and are not

cause for concern.

• Your icemaker will produce 8 cubes per cycle—approximately

120 cubes in a 24-hour period—depending on freezer compartment

temperature, room temperature, number of door openings and other

use conditions.

• Intermittent dispensing of ice is normal. If ice flow interruption is

more than brief, ice clump(s) may be the cause and should be

removed following instructions in this section.

• Avoid over-filling glasses with ice and using narrow or extra-tall

glasses. This can jam the chute or cause the door in the chute to

freeze shut. Periodically open the freezer compartment door and look

down into the chute. If ice is blocking the chute, poke it through with

a wooden spoon.

• To help keep bits of ice from being sprayed beyond the glass,

place the glass close to the ice chute—but not so close that it blocks

out-coming ice.

• Add ice before adding beverage to prevent splashing.

• Beverages and foods should not be quick-chilled in the ice

storage bin. Cans, bottles or food packages in the storage bin may

cause the icemaker or auger to jam.

• Do not add ice from trays or bags to the storage bin. It may not

crush or dispense well.

CAUTION: Some products such as water ices should not be

consumed too cold.

Rotate

Drive

Mechanism

STORAGE DRAWERS

Ice and Water Dispenser Storage Drawers

Convertible Drawer (on some models) Adjustable Humidity Drawers (on some models)

Refrigerator foods can be stored at colder temperatures by using the

convertible drawer.

The convertible drawer has its own cold air duct to allow a stream of

cold air from the freezer compartment to flow around the drawer.

The variable temperature

control regulates the air flow

from the freezer compartment.

Set the control lever up to convert

the drawer to normal refrigerator

temperature and provide extra

vegetable storage space. The

cold air duct is closed.

Push the control lever down to open the cold air duct and make the

convertible drawer colder. The amount of freezer air allowed in can

be varied by adjusting the control lever between the normal and

coldest setting.

These drawers have individual, adjustable humidity controls that let

you regulate the amount of moisture retained in foods.

Slide the control all the way to the setting and the drawer

provides high humidity recommended for most vegetables.

Slide the control all the way to the setting to provide lower

humidity levels recommended for most fruits.

Sealed Snack Pack (on some models)

The Sealed Snack Pack—and shelf to which it is attached—can be relocated within the Fresh

Food compartment. The sealed drawer retains sufficient humidity for convenient storage of

lunch meats, cheese, hors d’oeuvres, spreads and snacks.

Normal

setting

Coldest

setting

(on some models)

Storage time will depend upon the type of food and its condition when placed in the drawer. Excess water which may accumulate in the bottom of

the drawer should be poured out and the drawer wiped dry. The drawer is partially sealed by gaskets.

Always push the drawer all the way in.

As in any refrigerated storage area, it is recommended that odorous foods be stored wrapped.

SHELVES

Quick Space Shelf Slide-Out Spillproof Shelf (on some models)

This shelf splits in half

and slides under itself for

storage of tall items on the

shelf below.

The slide-out shelf allows you to reach

items stored behind others. The special

edges are designed to help prevent

spills from dripping to lower shelves.

Make sure you push the shelves all the

way back in before you close the door.

How to Rearrange Your Shelves

and Freezer Baskets

Glass and wire shelves are adjustable. This allows you to move the

shelves around to fit your family’s food storage needs.

To remove shelves:

Tilt the shelf up at front, then lift

it up and out of the tracks on the

rear wall.

To relocate shelves:

Select desired shelf height. With

shelf front raised slightly, engage

the top hooks in the tracks at the

rear of the cabinet. Then lower

the front of the shelf until it

locks into position.

Wire slide-out freezer baskets can be

relocated in the same way.

Bins on Fresh Food Compartment Door

(on some models)

Adjustable bins can easily be carried from refrigerator to work area.

To remove:

Tilt the bin up and pull out on the molded

supports until it comes completely out of

the door.

To replace or relocate:

Select desired shelf height, engage the

bin in the molded supports of the door

and slide the bin in. The bin will hook

in place.

The divider (on some models) helps

prevent tipping, spilling or sliding of

small items stored on the door shelf.

Place index finger and middle finger on

either side of the divider near the front

and simply move it back and forth to fit

your needs.

To remove fixed bins, first remove

the food in the bins. Then, grasping the

bin at each end, push in at the bottom

as you lift and pull out at the top.

Lift up

and out

Tilt up

Lower to

lock into place

Engage

top hook

Divider

Shelves

Loading the Freezer Compartment

Load so that at least 15 mm of space remains clear between stacks of

packages and 15 mm to 25 mm of space between the top of any stack

and any shelf or basket above it. Packages may hang over the front of

shelves but must remain 15 mm from doors.

• Food to be frozen must not be placed in direct contact with food in

storage. If food is to be frozen every day, it may be necessary to

reduce the quantity to be frozen.

• If a quantity of food needs to be frozen set the freezer control to its

coldest setting. After the food is frozen reset the freezer control to its

initial position.

• Food is most quickly frozen on the middle three shelves of the

freezer compartment and most slowly in the freezer door shelves.

• Do not store commercially quick-frozen food longer than the time

recommended by the food manufacturers.

• If the power to the appliance is shut off for an extended time or if the

refrigerating system fails, do not open the doors unless absolutely

necessary. When it is necessary, close them as quickly as possible so

the frozen food will stay frozen as long as possible.

• The freezer door storage shelves marked with a two-star label are

only appropriate for the storage of previously frozen food.

Effervescent drinks should not be stored in the freezer

compartment.

Removable Wine Rack

The wine rack is designed to hold a bottle on its side.

A good location for the wine rack is the Quick Space Shelf.

Freezer Baskets (on some models) Quick-Serve System

(on some models)

Wire slide-out freezer baskets

can be pulled out for easy access to

frozen foods.

WARNING: Poor performance may

occur if freezer baskets are not used.

Storage of items in the freezer without

using baskets may result in poor

temperature performance due to

restrictions of air flow within the

freezer compartment.

Cooking-serving-storage dishes with

durable lids fit into a space saving under-

the-shelf rack.

Dishes can be removed from and

returned to the rack as needed, and the

rack (and shelf to which it is attached)

can be relocated anywhere in the fresh

food compartment.

Dishes and lids are safe for use in microwave ovens, refrigerators,

freezers, and are dishwasher-safe. The dishes should not be used for

cooking high-fat foods, such as bacon, and high-sugar foods, such as

candy and syrup. The high temperatures of the fat and sugar can cause

bubbles to form on the inside of the dish.

CAUTION: Dishes and lids are not designed for use on the range

top, broiler or in the regular oven. Such use can be hazardous.

CARE AND CLEANING

Cleaning—Outside

Refreshment Center Compartment door—outside. It’s important

that you use only window cleaner without ammonia or a damp cloth

to clean the glass and trim. Avoid using wax on the Refreshment

Center door.

The dispenser well, beneath the grille, should be wiped dry. Water

left in the well may leave deposits. Remove the deposits by adding

undiluted vinegar to the well. Soak until the deposits disappear or

become loose enough to rinse away.

The dispenser pad can be cleaned by using a warm water and baking

soda solution—about 15 ml of baking soda to one liter of water. Rinse

thoroughly with water and wipe dry.

The door handles and trim can be cleaned with a cloth dampened

with a solution of mild liquid dishwashing detergent and water. Dry

with a soft cloth. Don’t use wax on the door handles and trim.

Keep the finish clean. Wipe with a clean cloth lightly dampened with

kitchen appliance wax or mild liquid dishwashing detergent. Dry and

polish with a clean, soft cloth. Do not wipe the refrigerator with a

soiled dishwashing cloth or wet towel. These may leave a residue that

can erode the paint. Do not use scouring pads, powdered cleaners,

bleach or cleaners containing bleach because these products can

scratch and weaken the paint finish.

Protect the paint finish. The finish on the outside of the refrigerator

is a high quality, baked-on paint finish. With proper care, it will stay

new-looking and rust-free for years. Apply a coat of kitchen/appliance

wax when the refrigerator is new and then at least twice a year.

Cleaning—Inside

Refreshment Center Compartment door—inside. Wipe up spills

right away. Use 15 ml of baking soda in one liter of water to clean the

inside door surface, Refreshment Center bin and inside access door.

Rinse, wipe dry.

Inside the fresh food and freezer compartments should be cleaned

at least once a year. Unplug the refrigerator before cleaning. If this is

not practical, wring excess moisture out of sponge or cloth when

cleaning around switches, lights or controls.

Use warm water and baking soda solution—about 15 ml of baking

soda to one liter of water. This both cleans and neutralizes odors.

Rinse thoroughly with water and wipe dry.

Other parts of the refrigerator—

including door magnets, meat and vegetable

drawers, ice storage bin and all plastic

parts—can be cleaned the same way.

Avoid cleaning cold glass shelves with hot

water because the extreme temperature

difference may cause them to break.

To help prevent odors, leave an open box of baking soda in the

rear of the refrigerator, on the top shelf. Change the box every 3

months. An open box of baking soda in the freezer will absorb stale

freezer odors.

Quick-Serve

dishes and lids can be cleaned in an automatic

dishwasher or by hand with liquid dishwashing detergent and water.

You can remove stains by soaking them in a bleach and water solution

using one part chlorine bleach to three parts water. (Stubborn stains

may require soaking.) Use a plastic scouring pad to remove burned-on

soil. Do not use cleansing powders or other abrasive cleaners.

Do not wash any plastic parts from your refrigerator in

your automatic dishwasher.

Door magnets

Cleaning the Decorator Door Panels

Clean these panels using an anti-static cleaner or a mild detergent

and water. (Look for anti-static cleaner in electronic or computer

departments.) Rinse thoroughly and blot dry with a clean, damp cloth

or chamois. Do not use paper towels to wash or dry the panels. Do not

use cleaners that contain solvents such as ammonia, because they can

damage the panels.

Shallow scratches and abrasions can be corrected with a good grade

of hard automobile paste wax. The wax will fill in any minor surface

scratches and will help to maintain the luster of the panels. Apply the

wax sparingly and buff lightly with a clean, soft cloth using a circular

motion. Do not use a cleaner/wax combination.

Care and Cleaning

Under Refrigerator Behind Refrigerator

For most efficient operation,

you need to keep the area under the

refrigerator clean. Remove the base

grille and either sweep away or

vacuum up dust that is readily

accessible on the condenser coils.

To remove the base grille, open

both doors, grasp the bottom of

the grille and pull it out.

To replace the base grille,

line up the clips on the back

of the grille with the openings

in the baseplate and push the

grille forward until it snaps

into place.

Care should be taken in moving your refrigerator away from the wall.

All types of floor coverings can be damaged, particularly cushioned

coverings and those with embossed surfaces. Pull the refrigerator

straight out and return it to position by pushing it straight in. Moving

your refrigerator in a side direction may result in damage to your floor

covering or refrigerator.

When pushing the refrigerator back, make sure you don’t roll over the

power cord or icemaker supply line.

Clean the condenser coils

at least once a year.

Drawer and Cover Removal

Drawers will stop before coming all the way out of the refrigerator to

help prevent contents from spilling onto the floor. Drawers can easily

be removed by tilting up slightly and pulling past the “stop” location.

Remove the door bins from the fresh food door before removing

the drawer.

To remove the shelf above the top

drawer, first remove the top drawer

and any food on the shelf. Then tilt

the shelf up at the front and lift it up

and out of the tracks.

To replace the shelf, raise the

shelf front slightly and place the

top hooks in the lowest large track

slots. Then lower the front of the

shelf until it is level.

When replacing the drawers, make

sure you slide them through both

drawer guides on the right side.

To remove the drawers when the

fresh food compartment door

cannot be opened fully you need to

roll the refrigerator forward until

the door can be fully opened. In

some cases this will require moving

the refrigerator to the left as you roll it out.

Drawer

Guides

Light Bulb Replacement

Fresh Food Compartment—Upper Light

1. Unplug refrigerator.

2. Remove the snap-in light shield.

3. Replace with same size bulb and reinstall the light shield. If you

cannot locate the correct bulb, see your dealer.

Fresh Food Compartment—Lower Light (on some models)

This light is located behind a shield at the rear of the fresh food

compartment.

1. Unplug the refrigerator.

2. Grasp the top edge of the shield and lift it up and forward to free its

top edge.

3. After replacing with the same size bulb, hook the top of the shield

back in place. If you cannot locate the correct bulb, see your dealer.

4. Plug the refrigerator back in.

Freezer Compartment with a Dispenser

1. Unplug the refrigerator.

2. Remove the shelf just below the light shield. (The shelf will be

easier to remove if it is emptied first.)

3. Pull the light shield toward you to reach the bulb.

After replacing with same size bulb, reinstall shelf and plug the

refrigerator back in.

3 5

PREPARATION

Preparing for Vacation Preparing to Move

For extended vacations or absences, shut off the power to the

refrigerator, move the control to the

“ ”

position, and clean the

interior with a baking soda solution of 15 ml of baking soda to 1 liter

of water. Wipe dry. To prevent odors, leave an open box of baking

soda in the refrigerator. Leave doors open.

Move icemaker feeler arm to (up) position, which stops

icemaking, and be sure to shut off water supply to the refrigerator.

For shorter vacations, remove perishable foods and leave

controls at regular settings. However, if room temperature is

expected to drop below 16°C, follow the same instructions

as for extended vacations.

Disconnect power cord from wall outlet, remove all food, and clean

and dry the interior.

Secure all loose items such as grille, shelves and storage pans by

taping them securely in place to prevent damage.

Be sure refrigerator stays in

upright position during actual moving and

in van. Refrigerator must be secured in van to prevent movement.

Protect outside of refrigerator with blanket.

Refrigerator Location Water Supply to Icemaker

Install it on a floor strong enough to support a fully loaded

refrigerator.

Clearances

Allow the following clearances for ease of installation, proper air

circulation, plumbing and electrical connections.

24 Model 28 Model 30 Model

Sides 3 mm 3 mm 3 mm

Top 25 mm 3 mm 3 mm

Back 13 mm 13 mm 13 mm

[If built-in, allow 22 mm for hinge covers.]

If the refrigerator is against a wall on either side, allow 19 mm for

freezer door clearance and 19 mm for fresh food door clearance.

If your refrigerator has an icemaker, or if you plan to add an

icemaker later, the icemaker will have to be connected to a cold

drinking (potable) water line.

A water supply kit containing copper tubing, shutoff valve, fittings

and instructions is available at extra cost from your dealer. There

should be sufficient tubing from the cold water supply to the

icemaker inlet to allow moving the refrigerator out from the wall

several feet (approximately 2.5 m of 1/4

² copper tubing in three

25 cm diameter coils).

Do not use kits with plastic tubing since there is water pressure in the

supply line at all times.

Maximum permissible inlet water pressure—8.3 bars.

Minimum permissible inlet water pressure—1.4 bars.

Installation of icemaker must be made by a qualified service technician.

Dimensions

24 Model 28 Model 30 Model

A* 1746 mm A* 1746 mm A* 1746 mm

B 908 mm B 908 mm B 908 mm

C 719 mm C 833 mm C

✝ 876 mm

D 1153 mm D 1251 mm D 1251 mm

* Height does not include hinge.

✝ Add 14 mm for water hook-up.

The rollers have two purposes:

1. The rollers can be adjusted so the refrigerator is firmly positioned

on the floor and does not rock back and forth.

2. The rollers allow you to move the refrigerator away from the wall

for cleaning.

To adjust the rollers:

1. Remove the base grille by

grasping it at the bottom

and pulling it out.

2. Turn the two front roller adjusting screws clockwise to raise the

refrigerator, counterclockwise to lower it. Use a 3/8² socket wrench,

adjustable wrench or pliers.

3. Built-In Style models also have rear adjustable rollers so you can

align the refrigerator with your kitchen cabinets. Use a 5/16² socket

wrench to turn the screws for the rear rollers—clockwise to raise it,

counterclockwise to lower it.

After leveling, make sure that the doors are even

at the top.

To make the doors even,

adjust the fresh food door.

Insert a 3/16² Allen

wrench into the bottom

of the hinge pin. Turn the

door adjusting screw to

the right to raise the door,

to the left to lower it.

(A nylon plug, imbedded

in the threads of the pin,

prevents the pin from turning

unless a wrench is used.)

After one or two turns of the

wrench, open and close the

fresh food door and check the

alignment at the top of the doors.

Preparation

Leveling Rollers Door Alignment

Uneven Doors

Make sure doors

are even at the top.

3/16² Allen Wrench

Hinge Pin

Raise

Front Roller

Adjusting

Screw

Front Roller

Adjusting

Screw

Rear Roller Adjusting

Screw (on Built-In

Style models only)

Use this screw if the

refrigerator has one.

Rear Roller Adjusting Screw

(on Built-In Style models

only) Use this screw if the

refrigerator does not have the

screw pictured to the left.

Dimensions and Specifications (for Built-In Style models)

1784 mm

914 mm

619 mm

Cabinet

619 mm

Side Panels

Water

Electrical

19 mm Airspace

(13 mm Gap +

6 mm Wall Plates)

635 mm

Counter

Top

TRIM KITS

(for Built-In Style models)

Some models are equipped with trim kits that allow you to install door panels. You can

order pre-cut black or white decorator panels from your dealer, or you can add wood panels

to match your kitchen cabinets.

Panels Less Than 6 mm Thick

When installing wood panels less than 6 mm thick, you need to create a filler panel, such as

1/8

² cardboard, that will fit between the face of the door and the wood panel. If you are

installing the pre-cut decorator panels, pre-cut filler panels are included in the kit. The

combined thickness of the decorator or wood panel and the filler panel should be 6 mm.

19 mm or Raised Panel

A raised panel design screwed or glued to a 6 mm thick backing, or a

19 mm routed board can be used. The raised portion of the panel must

be fabricated to permit clearances of at least 51 mm from the handle

side for fingertip clearance.

Weight limitations for custom panels:

Fresh Food: 16 kg max.

Freezer Door: 11 kg max.

6 mm

Thick Backing

Refrigerator

Door

19 mm

Appearance

Panel

51 mm

Clearance

Handle Side

Dimensions

Wood panels need to be cut to the following specifications.

Cut

out

Depth of material

to be routed out

Cut

out

Cut

out

Cut

out

956 mm 956 mm

60 mm 60 mm 60 mm

60 mm 60 mm

60 mm

29 mm 29 mm 29 mm

29 mm 29 mm

29 mm

286 mm 286 mm 286 mm286 mm

478 mm 478 mm

368 mm 368 mm 491 mm 491 mm

872 mm 872 mm

122 mm 122 mm

25 mm 25 mm 25 mm 25 mm

50 mm 50 mm 50 mm 50 mm

6 mm

Front

4 mm

1705 mm 1705 mm

8 mm 8 mm

8 mm

3 mm 3 mm 3 mm 3 mm

FRONT FRONT FRONT FRONT

Example of Routing

The areas at the top of the

panels need to be cut out of

the panels. The shaded

areas indicate areas that

must be routed out about

4 mm on the back side of

panels 6 mm thick or more.

For panels less than 6 mm

thick, these areas can be

cut out of the filler panels.

Freezer Panel

Without Dispenser

Freezer Panels

With Dispenser

Fresh Food Panel

with Refreshment

CenterFresh Food Panel

29 mm

Trim Kits and Decorator Panels

Inserting the Door Panels

1. Loosen the Top Trim on the freezer and fresh food doors.

• Using a T-20 Torx driver, loosen the two screws attaching the Top

Trim about 6 mm.

2. Insert the panels.

Freezer panel and fresh food panel

• Lift the Top Trim up 6 mm and carefully push the top freezer panel

in until it slides into the slot behind the door handle. Push the filler

panel (required with some door panels) in behind the decorator

panel. Repeat for fresh food panel.

If your model has a dispenser and/or a Refreshment Center, this

step only applies to the top panels.

Bottom freezer panel (for models with a dispenser and/or a

Refreshment Center)

• Carefully push the panel in until it slides into the slot behind the

door handle. Push the filler panel (required with some door panels)

in behind the decorator panel.

3. Tighten the two screws on the Top Trim to 30 in-lbs torque.

4. Install the Side Trim. These pieces are tucked inside the fresh food

door handle.

Do not remove the protective film on the outside of the Side Trim

until the Side Trim is installed.

• Fit the bottom of the Side Trim under the Bottom Trim as

illustrated.

• Hold the Side Trim against the front face of the decorator panels

and fit the Side Trim under the Top Trim. Make sure the Side Trim

is fitted correctly and that you are satisfied with the appearance of

all the parts before pulling the tape liner.

5. Secure the Side Trim.

• Place one hand between the two pieces of tape liner and hold the

Side Trim firmly against the panels and the side of the door.

• Pull the top tape liner up about 80 mm, pressing the trim with your

hand as the adhesive is exposed to the door. Then pull the bottom

tape liner down about 80 mm. Follow the tape with your hand,

pressing the trim adhesive against the door.

• Continue pulling the tape liner loose, alternating between the top

and bottom and pressing the Side Trim against the door.

6. Remove the protective film from the outside of the Side Trim.

Top Trim Screws

Cut-out

Top

Freezer

Panel

Fresh Food

Panel

Bottom

Freezer

Panel

Side

Trim

Side

Trim

Tape

Liner

Top Trim

Side

Trim

Tape

Liner

Tape

Liner

Side

Trim

Bottom Trim

INSTALLING AND REMOVING PREVIOUSLY

INSTALLED DECORATOR PANELS

In order to remove the decorator panels and replace with new panels

you need to remove the handles. A T-20 Torx driver is needed.

Removing the Handles:

1. Loosen and remove the 2 screws in the Top Trim.

2. Loosen and remove the 2 screws in the bracket that attaches the

Handle to the top of the Door.

3. Grip the Handle firmly and slide upwards. The keyhole slots on the

Handle slide off the buttons on the door.

4. Open the door and slide out the decorator panels.

Inserting the Door Panels:

Before installing the decorator panels, make sure they have been

routed out in the proper areas as shown in the beginning of this

section. Slide in the panels to perform a trial fit before fastening down

the Handle and Top Trim.

Installing the Handles:

Once the panels are fitted properly, install the Handle and Top Trim.

1. Slide the keyhole slots on the Handle down onto the buttons

mounted to the face of the door. Slide the Handle downward until

the bracket at the top of the Handle fits flush on the top of the door.

2. Replace the two screws in the bracket that attach the Handle to the

top of the Door and tighten the screws to 45 in-lbs torque.

3. Replace the Top Trim making sure it fits over the Side Trim and

that the locating tabs fit the inside of the Handle profile.

4. Replace the Top Trim screws and tighten to 30 in-lbs torque.

Buttons

Button

Top Trim Screws

Bracket Screws

Bracket

Slots

Slot

The refrigerator should always be plugged into its own individual

electrical outlet— Please refer to the rating plate on the refrigerator

for the correct voltage and frequency. This is recommended for best

performance and to prevent overloading house wiring circuits, which

could cause a fire hazard from overheated wires.

WARNING: HOW TO AVOID ACCIDENTS TO CHILDREN.

WHEN DISCARDING AN OLD REFRIGERATOR OR

FREEZER BE CERTAIN TO MAKE THE LOCK UNUSABLE.

IF POSSIBLE, REMOVE THE DOORS AND DISCARD

SEPARATELY. DO NOT ATTEMPT TO STAND ON TOP OF

YOUR APPLIANCE. IT IS NOT DESIGNED FOR SUCH USE

AND YOU COULD INJURE YOURSELF OR DAMAGE THE

APPLIANCE BY SUCH ABUSE. CHILDREN SHOULD NOT

BE ALLOWED TO PLAY WITH THE APPLIANCE OR

TAMPER WITH THE CONTROLS.

Electrical Requirements

INSTALLATION REQUIREMENTS

IMPORTANT…Please read carefully

Trim Kits and Decorator Panels Installation

How to Connect Electricity

For personal safety, this appliance must

be properly earthed.

The power cord of this appliance is

equipped with an earthing plug

which mates with a standard

grounding wall outlet to minimize

the possibility of electric shock

hazard from appliance.

Have the wall outlet checked by a

qualified electrician to make sure

the outlet is properly earthed.

Where an unearthed wall outlet is encountered, it is your personal

responsibility and obligation to have it replaced with a properly

earthed wall outlet.

If the power supply cord becomes damaged, it must be replaced by

a qualified service agent in order to avoid a safety hazard.

If the plug does not fit your outlet a new plug can be fitted.

IMPORTANT: In some countries the refitting of electric plugs

and cables is only permitted when the work is completed by a

qualified technician.

Insure proper

earthing exists

before using.

Earthing plug

INSTALLATION INSTRUCTIONS

FOR GREAT BRITAIN AND IRELAND ONLY

Electrical Requirements

We recommend that this appliance is connected to the mains supply via a suitable switched

socket in a readily accessible position. All appliances come complete with a fitted plug. The

plug on your refrigerator has a 13A fuse. If the plug does not fit your sockets, a new plug can

be fitted. Cut off the old plug and throw it away. Do not insert it into a socket elsewhere in

the house as this could cause a shock.

WARNING: THIS APPLIANCE MUST BE EARTHED.

IMPORTANT: Fitting a Different Plug

The wires in the mains lead are coloured in accordance with the

following code: Green and Yellow-Earth; Blue-Neutral; Brown-Live.

If you fit your own plug the colours of these wires may not correspond

with the identifying marks on the plug terminals. This is what you

have to do:

1. Connect the green and yellow

(Earth) wire to the terminal

in the plug marked ‘E’ with

the symbol or coloured green

or green and yellow.

2. Connect the blue (Neutral) wire

to the terminal in the plug

marked ‘N’ or coloured black.

3. Connect the brown (Live) wire to

the terminal marked ‘L’ or

coloured red.

If the plug is the moulded-on type the fuse cover must be refitted

when changing the fuse. In the event of losing the fuse cover the plug

must not be used until a replacement fuse cover has been obtained and

fitted. A new fuse cover can be obtained from your nearest Service

Centre or local Electricity Board. The colour of the correct

replacement fuse cover is that of the coloured marks or insert in the

base of the plug.

In the event of replacing a fuse in the plug supplied with this

refrigerator a 13A ASTA approved fuse to BS1362 must be fitted.

With an alternative plug a 15A fuse must be fitted either in the plug or

adapter or the main fuse box.

13 AMP

Mains Lead Replacement

If the mains lead on this appliance needs replacing at any time, it must be replaced by a

special lead which is obtainable from your nearest Service centre. A charge will be made for

the replacement of the mains lead if you have damaged the lead.

Green

Yellow

Blue

Brown

Cord Grip

La page charge ...

GE TPG24BRDBS Mode d'emploi

Marque: GE

Modèle: TPG24BRDBS

Catégorie: Frigos

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: GE TPG24BRDBS User guide
español: GE TPG24BRDBS Guía del usuario

GE TPG24BRDBS Mode d'emploi

GE TPG24BRDBS Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents