GE GDT625PSJSS Le manuel du propriétaire

Write the model and serial

numbers here:

Model # _________________

Serial # _________________

You can find them on a label on

the tub wall just inside the door.

GE is a trademark of the General Electric Company. Manufactured under trademark license.

OWNER’S MANUAL

DISHWASHERS

49-55117 05-17 GEA

ENGLISH/FRANÇAIS/

ESPAÑOL

GDF500-620 Series

GDT535-635 Series

SAFETY INFORMATION .........4

USING THE DISHWASHER

Getting Started ........................6

Dispensers ............................9

Loading ............................. 11

CARE AND CLEANING ............15

TROUBLESHOOTING TIPS ......17

WARRANTY ......................21

CONSUMER SUPPORT ..........22

FRONT CONTROL MODELS TOP CONTROL MODELS

2 49-55117

THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.

Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.

We take pride in the craftsmanship, innovation and design that goes into every GE Appliances

product, and we think you will too. Among other things, registration of your appliance ensures that we

can deliver important product information and warranty details when you need them.

Register your GE appliance now online. Helpful websites and phone numbers are available in the

Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration

card included in the packing material.

49-55117 3

WELCOME

Notes

4 49-55117

SAFETY INFORMATION

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

WARNING

For your safety, the information in this manual must be followed to minimize

the risk of fire, explosion, electric shock, and to prevent property damage, personal injury,

or death.

WARNING

PROPER INSTALLATION AND MAINTENANCE

This dishwasher must be properly installed and located in accordance with the Installation Instructions before

it is used. If you did not receive an Installation Instructions sheet with your dishwasher, you can receive one by

visiting our Website at GEAppliances.com. In Canada, visit www.GEAppliances.ca.

Ŷ

Connect the dishwasher/appliance to a grounded

metal, permanent wiring system; or run an

equipment-grounding conductor with the circuit

conductors and connect to the equipment-grounding

terminal or lead of the appliance.

Ŷ

Improper connection of the equipment-grounding

conductor can result in a risk of electric shock.

Check with a qualified electrician or service

representative if you are in doubt whether the

appliance is properly grounded.

Ŷ

Dispose of discarded appliances and shipping or

packing material properly.

Ŷ

Do not attempt to repair or replace any part of your

dishwasher unless it is specifically recommended in

this manual. All other servicing should be referred to

a qualified technician.

Ŷ

Use only cord kit WX09X70910 or hard-wire to

building electrical. Failure to follow this instruction,

could result in risk of fire and personal injury.

Ŷ

To minimize the possibility of electric shock,

disconnect this appliance from the power supply

before attempting any maintenance.

NOTE: Turning the dishwasher off does not

disconnect the appliance from the power supply.

We recommend having a qualified technician

service your appliance.

WARNING

WHEN USING YOUR DISHWASHER, FOLLOW BASIC PRECAUTIONS,

INCLUDING THE FOLLOWING:

Ŷ

Use this appliance only for its intended purpose as

described in this Owner’s Manual.

Ŷ

Use only detergents or wetting agents

recommended for use in a dishwasher and keep

them out of reach of children. Using a detergent

that is not specifically designed for dishwashers will

cause the dishwasher to fill with suds.

Ŷ

Locate sharp items so that they are not likely to

damage the door seal.

Ŷ

Load sharp knives with the handles up to reduce

the risk of cut-type injuries.

Ŷ

Do not wash plastic items unless marked

dishwasher safe or the equivalent. For plastic

items not so marked, check the manufacturer’s

recommendations.

Ŷ

Do not touch the heating element during or

immediately after use.

Ŷ

Do not operate your dishwasher unless all

enclosure panels are properly in place.

Ŷ

Do not tamper with controls.

Ŷ

Do not abuse, sit on or stand on the door or dish

rack of the dishwasher.

Ŷ

To reduce the risk of injury, do not allow children to

play with, on or inside this appliance at any time.

Ŷ

Do not store or use combustible materials including

gasoline or other flammable liquids or vapors in the

vicinity of this or any other appliance.

Ŷ

Small parts, such as rack clips and filter retaining

posts, can be a choke hazard to small children if

removed from the dishwasher. Keep out of reach of

small children.

49-55117 5

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

WARNING

WATER HEATER SAFETY

Under certain conditions, hydrogen gas may be produced in a water heater that has not been used for two or more weeks.

HYDROGEN GAS IS EXPLOSIVE.

If the hot water has not been used for two or more weeks, prevent the possibility of damage or injury by turning

on all hot water faucets and allowing them to run for several minutes. Do this before using any electrical

appliance connected to the hot water system. This simple procedure will allow any built-up hydrogen gas to

escape. Since the gas is flammable, do not smoke, use an open flame, or use the appliance during this process.

TO PREVENT MINOR INJURY AND PROPERTY DAMAGE

Ŷ

During or after wash cycle, contents may be hot to

the touch. Use care before handling.

Ŷ

Close supervision is necessary if this appliance is

used by or near children. Do not allow children to

play around the dishwasher when closing the door,

closing the upper rack, or while vertically adjusting

the upper rack due to the possibility of small fingers

being pinched.

Ŷ

Non-Dishware Items: Do not wash items such as

electronic air cleaner filters, furnace filters and

paint brushes in your dishwasher. Damage to the

dishwasher and discoloration or staining of the

dishwasher may result.

Ŷ

Load light-weight, plastic items so they do not

become dislodged and drop to the bottom of the

dishwasher—they might come into contact with the

heating element and be damaged.

WARNING

RISK OF CHILD ENTRAPMENT

PROPER DISPOSAL OF THE DISHWASHER

Junked or abandoned dishwashers are dangerous…even if they will sit for “just a few days.”

If you are getting rid of your dishwasher, please follow the instructions below to help prevent

accidents.

Ŷ

Do not allow children to play with, on, or inside this or any discarded appliance.

Ŷ

Take off the door of the washing compartment or remove the latch by removing the two

screws from the latch receiver inside the tub (as shown).

CAUTION

ELECTRICAL REQUIREMENTS

Ŷ

This appliance must be supplied with 120V, 60 Hz,

and connected to an individual, properly grounded

branch circuit, protected by a 15 or 20 amp circuit

breaker or time-delay fuse.

Ŷ

If the electric supply provided does not meet the

above specifications, it is recommended that a

licensed electrician install an approved outlet.

Ŷ

Your dishwasher circuit should not be used for any

other appliance while the dishwasher is in operation as

the dishwasher requires the full capacity of the circuit.

CAUTION

NOTICE

Ŷ ,I\RXUGLVKZDVKHULVFRQQHFWHGWRDZDOOVZLWFK

ensure that the switch is on prior to use.

Ŷ ,I\RXFKRRVHWRWXUQWKHZDOOVZLWFKRIIEHWZHHQ

wash cycles, allow 5-10 seconds after turning the

switch on before touching Start to allow the control

to initialize.

Ŷ 8VHRQO\SRZGHUFinish

®

Quantum

®

Automatic

Dishwashing Detergent, liquid detergents or rinse

agents recommended for use in a dishwasher and

keep them out of the reach of children. Finish

®

Quantum

®

Automatic Dishwashing Detergent,

and Finish

®

Jet-Dry

®

Rinse Aid rinse agents

have been approved for use in all GE Appliances

dishwashers.

SAFETY INFORMATION

Two screws

6 49-55117

Getting started

USING THE DISHWASHER

Features and appearance will vary throughout this manual

Select Cycle

Press the Select Cycle pad for the desired wash cycle. The light next to the Select Cycle pad will be lit to

indicate which wash cycle has been selected.

NOTE: Cycle times vary based on soil level, water temperature, and options selected.

The cycle may be selected with the door in the open position. The cycle will not start until the Start pad is

pushed and the door is closed within 4 seconds.

AutoSense

(on some

models)

This cycle automatically senses the soil level and adjusts the wash cycle accordingly.

Heavy This cycle is meant for heavily soiled dishes, cookware, pots, or pans with dried-on or baked-on

soils. Everyday dishes are safe to be used in this cycle.

Normal This cycle is meant for daily, regular, or typical use to completely wash a full load of normally

soiled dishes and is designed to conserve both water and energy. NOTE: Normal was used to

rate the energy efficiency of this dishwasher.

Light This cycle is for light to medium soiled dishes. It is safe for china and crystal with no options

selected.

Rinse

(on some

models)

For rinsing partial loads that will be washed later. Do not use detergent. Detergent is not

dispensed during the rinse cycle.

4

Load Dishwasher

For best dishwashing results, follow the loading guidelines found in the Loading section. No pre-rinsing of

normal food soil is required. Scrape off hard soils, including bones, toothpicks, skins, and seeds. Remove

leafy vegetables, meat trimmings, and excessive amounts of grease or oil.

Add Detergent

Add needed amount of detergent to the detergent dispenser. Use detergent such as Finish

®

Quantum

®

Automatic Dishwashing Detergent. See Dispensers section.

Add Rinse Agent

Add rinse agent such as Finish

®

Jet-Dry

®

Rinse Aid to the rinse agent dispenser. See Dispensers section.

1

2

3

49-55117 7

USING THE DISHWASHER

Getting started

Select Options

The light by the selected pad will be lit to indicate which Option has been selected.

Wash

Temp

Boost

(on some

models)

This option increases the temperature to help clean heavily soiled dishes and will increase the

cycle time by 20 to 50 minutes. Option may be turned On or Off during the wash cycle. This

option will also improve dry performance on the Normal cycle.

Wash

Temp Sani

(on some

models)

This option raises the water temperature in the final rinse to sanitize your dishware but may

increase cycle time by 60 minutes. The cycle length will vary depending on the temperature of

your inlet water.

NOTE: This option is monitored for sanitization requirements. If the cycle is interrupted during

or after the main wash portion or if the incoming water temperature is so low that adequate

water heating cannot be achieved, the sanitizing conditions may not be met. In these cases, the

Sanitized light will not illuminate at the end of the cycle. Utilizing this option will modify the cycle

to meet the requirements of Section 6, NSF 184 for soil removal and sanitization efficacy.

NOTE: NSF certified residential dishwashers are not intended for licensed food establishments.

Heated

Dry Off

Shuts off the drying option. Dishes air dry naturally and energy is saved. Open the dishwasher

door to speed drying.

Heated

Dry On

Turns on the option for faster drying. This option may add up to 85 minutes to the cycle time.

This option is not available with the Rinse cycle.

Steam

(Prewash)

(on some

models)

For use with heavily soiled and/or dried-on, baked-on soils. This option MUST be selected

PRIOR to starting the cycle. The Steam option adds up to 30 minutes to the cycle time. This

option is available with Heavy, AutoSense, and Normal cycles.

Wash

Zones

(on some

models)

Selecting either the Upper or Lower Wash Zones will target dishwashing of just one rack. This

will shorten the cycle time and conserve energy. This option should be used when dishes are

placed in only one rack.

Bottle Jets

(on some

models)

This option increases the time that the bottle jets are on and may add up to 23 minutes to the

cycle time. Use this to wash difficult to clean, dishwasher safe baby bottles, sport bottles, tall

coffee cups, etc. See use recommendations in the

Loading section.

Delay

Hours

(on some

models)

Delays the start of a wash cycle up to 8 to 12 hours depending on model. Press Delay Hours, to

select the number of hours, then press Start one time and close door to begin countdown. The

cycle will start once allotted time has expired.

Control

Lock

You can lock the controls to prevent selections from being made. You can also lock the

controls after you have started a cycle to prevent cycle changes. For example, children cannot

accidentally start the dishwasher by pressing pads with this option selected.

To LOCK the dishwasher control, depending on the model, press and hold the Heated Dry

pad for 3 seconds or press and hold the Steam and Wash Temp pads at the same time for 3

seconds. The Control Lock light will turn on to indicate the control is locked.

To UNLOCK the dishwasher control, depending on the model, press and hold the Heated Dry

pad for 3 second or press and hold the Steam and Wash Temp pads at the same time for 3

seconds. The Control Lock light will turn off to indicate the control is unlocked.

5

8 49-55117

Getting started

USING THE DISHWASHER

Start Dishwasher

Start Door can be open to select the desired options. Press the Start pad and close the door within

10 seconds to start the cycle or begin the Delay Hours countdown. The wash cycle will begin

shortly after closing the door. If the door is open, the illuminated lights will turn off if a pad is not

pressed within two minutes. To activate the display, close and open the door or press any pad.

Interrupt or

Pause

To interrupt or pause a dish cycle, slowly open the door. Opening the door will cause the wash

cycle to pause. The dishwasher will beep every minute to remind you to close the door. To restart

or resume the cycle, press Start, and close the door within 4 seconds.

Cancel To cancel a wash cycle, press and hold the Start pad for 3 seconds and close door.

The dishwasher will drain, emit a beep sound, and the wash cycle light will turn OFF.

6

Cycle Indicator Lights and Sounds

Sanitized Displayed at end of the cycle when Wash Temp Sani (Sanitize) has been selected and

dishwasher has met requirements for sanitization. See Wash Temp Sani (Sanitize), for

complete description. Opening the door or pressing any key while the door is closed will turn off

the light.

Clean Displayed when a wash cycle is complete. The light stays ON as a reminder that the dishes are

clean. Opening the door or pressing any key while the door is closed will turn the light off.

Sabbath/

Door

Wake Up

Mode

(on some

models)

To turn this option ON/OFF, press and hold the Start and Wash Temp pads for 5 seconds,

close the door and wait 3 minutes for the dishwasher to go into sleep mode. In the OFF mode,

the control display, control sounds, and interior lights (on some models) will not respond to the

door opening/closing. This mode can be used when observing certain religious holidays such as

the Sabbath. To activate the control and interior lights (on some models), press any button.

7

49-55117 9

USING THE DISHWASHER

Dispensers

Check the Water Temperature

The entering water should be at least 120°F (49°C) and

not more than 150°F (66°C) for effective cleaning and to

prevent dish damage. Check the water temperature with a

candy or meat thermometer.

Turn on the hot water faucet nearest the dishwasher,

place the thermometer in a glass and let the water run

continuously into the glass until the temperature stops

rising.

Use a Rinse Agent

Rinse agents, such as Finish

®

Jet-Dry

®

Rinse Aid are designed for great drying action and to protect against spots

and film build-up on your dishes, glasses, flatware, cookware, and plastic.

Filling the Rinse Agent Dispenser

The rinse agent dispenser holds 3.5 oz. (104 ml) of rinse agent. Under normal conditions, this will last approximately

one month.

1

Make sure the dishwasher door is fully open.

2

Open the rinse agent dispenser door.

3

Slowly add rinse agent until the cup is full. You may need to pause several times to

allow rinse aid to settle. NOTE: Indicator window does not light up.

4

Clean up any spilled rinse agent with a damp cloth to prevent foam from forming

inside the dishwasher.

5

Close the rinse agent dispenser door.

Rinse Aid Setting

The amount of rinse agent released into the final wash can be adjusted. If water drops or

hard water spots remain on dishes after the dry cycle, increase the setting.

To adjust the setting

Open the Rinse Agent dispenser door;

then turn the adjuster clockwise to

increase the amount of rinse agent,

counterclockwise to reduce the amount

of rinse agent.

Rinse

agent

adjuster

Clockwise to re-

duce water drops

and hard water

spots

Counterclockwise

to reduce foaming

Indicator

window

10 49-55117

Dispensers

USING THE DISHWASHER

Detergent Dispenser

The detergent dispenser is located in the center of

the dishwasher door. It has two compartments. The

main wash compartment is found inside the detergent

dispenser. To open, press the button on the side of the

dispenser. The pre-wash compartment is on the lid of

the detergent dispenser. Use the pre-wash compartment

only when your water is extremely hard or when you

have a heavy soiled load. The pre-wash compartment is

not used when tablet or packet detergents are used.

NOTE: Do not block detergent dispenser with large or

tall utensils.

You may use tablet, packet, powder, liquid or gel automatic

dishwasher detergent. Make sure you use only detergents

specifically labeled for use in automatic dishwashers. Never

use liquid hand dish detergent in an automatic dishwasher.

Sudsing and poor wash performance will result with the use

of improper detergents.

Detergents should be stored in a dry location and in their

original container to prevent loss of effectiveness. Place

detergent in the cup just prior to starting the dishwasher

and then close the cover. The cover will open during the

wash cycle.

Filling the Detergent Dispenser

GE Appliances recommends using detergent in tablet or

packet form. Independent testing has shown this form

of detergent is very effective in the dishwasher. Finish

®

Quantum

®

Powerball

®

is an example of this type of

detergent. Simply put a tablet or packet into the main

wash compartment and close the detergent cup cover.

Please notice that the tablet or packet must be placed in

the main wash compartment of the detergent cup. If the

tablet or packet is placed in the prewash compartment or

tossed in the bottom of the dishwasher, the detergent will

be flushed down the drain in a very short period of time

and will thus be wasted. Wash performance will be very

poor as a result.

If you choose to use detergent in powder, liquid or gel

form, the amount of detergent you use will be determined

by the hardness of your water, the temperature of your

water, and the food soil load inside the dishwasher.

Contact your water company to get information about the

hardness of the water in your area. Water hardness is

measured in grains per gallon. Use this information and

the table above to determine the amount of detergent

to use. You may purchase a hard water test strip from

GE Appliances. Call 1-877-959-8688 and ask for part

number WD01X10295. In Canada, call 1-800-661-1616.

Use the table as a starting point and then adjust the

amount of detergent you use. Use just enough to get

good wash performance. Using just the right amount of

detergent will provide great wash performance without

wasting detergent or etching glassware.

Using too much detergent with very soft and/or very

hot water may cause a condition called etching on your

glassware. Etching is a permanent cloudiness in your

glassware. This condition is irreversible. However, using

too little detergent will cause poor wash performance.

DO NOT USE HAND DISH DETERGENT

NOTE: Using a detergent that is not specifically designed

for dishwashers will cause the dishwasher to fill with suds.

During operation, these suds will spill out of the dishwasher

vents, covering the kitchen floor and making the floor wet.

Because so many detergent containers look alike,

store the dishwasher detergent in a separate space

from all other cleaners. Show anyone who may use the

dishwasher the correct detergent and where it is stored.

While there will be no lasting damage to the dishwasher,

your dishes will not get clean using a dishwashing

detergent that is not formulated for automatic dishwashers.

Number of

Grains/Gal.

Detergent Cup(s) to Fill

Less than 4 Fill cup to 1/3 full

4 to 8 Fill cup to 2/3 full

8 to 12 Fill cup completely full

Greater than 12

Fill both main wash cup and pre

wash cup

Pre-Wash

Main

Wash

Rinse Agent

Push/Slide

to Close

Detergent

Dispenser

49-55117 11

USING THE DISHWASHER

Loading

For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware

baskets may vary from your model.

Upper Rack

The upper rack is primarily for glasses, cups, and

saucers. For best wash performance, tilt cup and glass

openings toward the center of the rack. Other items such

as pots, pans, and plates may be placed in the upper

rack. This is also a secure place for dishwasher-safe

plastic items. The upper rack can be used for odd sized

utensils. Sauce pans, mixing bowls, and other similarly

shaped items should be placed face down for best wash

performance. Ensure small plastic items are secure so

that they cannot fall on the heater at the bottom of the

dishwasher, potentially damaging the item.

IMPORTANT: Ensure that items do not protrude through

the bottom of the rack or silverware basket where they

will block the rotation of the middle spray arm. This

could result in noise during operation and/or poor wash

performance.

End

Cap

Rollers

Rail

A loaded upper rack may be

heavier than anticipated. To prevent

minor injury or damage to the contents, do not raise

or lower the upper rack after the rack is loaded.

CAUTION

On some models, the upper rack may be adjusted to

accommodate larger items. To adjust the upper rack, fully

extend the upper rack and remove the two plastic end caps

on the front of the rails. Remove the upper rack. Select

the set of rollers on the side of the rack that provides the

desired height, and reinstall the upper rack by guiding the

rack rails between the appropriate set of rollers. With the

rack reinstalled, replace the two plastic end caps, ensuring

the snap is properly engaged. Failure to properly engage the

end caps may result in the rack falling from the dishwasher.

To add flexibility in loading, the stem safe shelf (on some

models) may be placed in the up or down position or

unfolded and placed in the lower unfolded position.

The shelf may also be used to secure stemware such as

wine glasses. Because these stemware items come in

various sizes, slowly push the rack in to ensure the items

do not bump into the edges of the dishwasher, which

may cause damage to the items.

Place the

slots in the

utility shelf

clips over

the vertical

rack wires

and

push

down to attach

utility shelf

onto

second

wire of rack

12 49-55117

Sports bottle held in place

over a Bottle Jets clip

Baby bottle held in place

under a Bottle Jets clip

Clip

Nozzle

Bottle Jets

The Bottle Jets system (on some models) is the ideal

location to position baby bottles, tall sports bottles, or

other tall items with narrow openings. The Bottle Jets

clips hold bottles with small openings in place so water

jets are directed inside the bottles to clean hard to reach

areas. Clips can be installed or removed by simply

slipping the clip opening over the top of the nozzle.

USING THE DISHWASHER

Loading

For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware

baskets may vary from your model.

Upper Rack - 10 Place Settings

GDF510-610, GDT535-545 & GDT625

Upper Rack - 12 Place Settings

GDF510-610, GDT535-545 & GDT625

Upper Rack - 8 Place Settings

GDF510-610, GDT535-545 & GDT625

Upper Rack - 8 Place Settings

GDF620 & GDT635

Upper Rack - 10 Place Settings

GDF620 & GDT635

Upper Rack - 12 Place Settings

GDF620 & GDT635

49-55117 13

USING THE DISHWASHER

Loading

Lower Rack

The lower rack is best used for plates, saucers and

cookware items. Large items, such as broiler pans and

baking racks should be placed along the sides of the rack.

If necessary, oversized glasses and mugs can be placed in

the lower rack to maximize loading flexibility. Plates, saucers

and similar items should be placed between the tines in the

direction that allows the item to remain secure in the rack.

IMPORTANT:

It is important to ensure that items do not

protrude through the bottom of the rack or the silverware

basket where they will block the

rotation of the lower spray arm. This

could result in noise during operation

and/or poor wash performance.

For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware baskets

may vary from your model.

Lower Rack - 10 Place Settings

GDF510 & GDT535

Lower Rack - 8 Place Settings

GDF510 & GDT535

Lower Rack - 10 Place Settings

GDF520, GDF610, GDT545

& GDT625

Lower Rack - 12 Place Settings

GDF520, GDF610, GDT545

& GDT625

Lower Rack - 8 Place Settings

GDF520, GDF610, GDT545

& GDT625

Lower

Rack - 12 Place Settings

GDF620 & GDT635

Lower

Rack - 8 Place Settings

GDF620 & GDT635

Lower

Rack - 10 Place Settings

GDF620 & GDT635

Lower Rack - 12 Place Settings

GDF510 & GDT535

14 49-55117

USING THE DISHWASHER

Loading

Mounting

Bosses

Silverware

Basket

Wire Loops

Silverware

Basket

Silverware Basket - 8 Place Settings

GDF520, GDF610, GDT545 & GDT625

Silverware Basket - 8 Place Settings

GDF620 & GDT635

Silverware Basket - 10 Place Settings

GDF620 & GDT635

Silverware Basket - 12 Place Settings

GDF620 & GDT635

Silverware Basket - 10 Place Settings

GDF520, GDF610, GDT545 & GDT625

Silverware Basket - 12 Place Settings

GDF520, GDF610, GDT545 & GDT625

Silverware Basket - 8 Place Settings

GDF510 & GDT535

Silverware Basket - 10 Place Settings

GDF510 & GDT535

Silverware Basket - 12 Place Settings

GDF510 & GDT535

For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware

baskets may vary from your model.

Silverware Basket

Place flatware in the removable silverware and

accessory baskets (on some models). Sharp objects,

such as forks and knives, may be placed with the

handles facing up, in order to protect your hands. For

the best wash performance, place other items such as

spoons with the handles facing down. Avoid allowing

items to nest together, which may keep them from being

properly washed. When loading, distribute items evenly

in the basket.

The silverware and accessory baskets (on some models)

may also be used for small items, such as measuring

spoons, baby bottle nipples, plastic lids, or corn cob

holders. The silverware basket covers (on some models)

can be closed to contain small items.

The door mounted silverware basket (on some models)

may be positioned either on the door by securing the

basket to the door using the two mounting bosses, or

to the rack by securing the basket to the rack using the

wire loop on the front of the lower rack to engage the

tabs on the rear of the basket.

The accessory basket (on some

models) may be positioned by

placing the hooks on the back of

the basket over the top wire on

the sides of the lower rack.

Secure the basket to the rack

using the wire loop on the front

of the upper and lower racks to

engage the tabs on the rear of the basket.

IMPORTANT: Do not load large or

tall utensils where they may block the

detergent dispenser, mid spray arm, or

become trapped between the door and

the gasket when the door is closed.

49-55117 15

Care and cleaning

USING THE DISHWASHER

Control Panel

To clean the control panel, use a lightly dampened cloth.

Then dry thoroughly.

Dishwasher Interior

To clean and de-odorize your dishwasher, use citric acid

or Finish

®

Dishwasher Cleaner, a detergent additive.

Finish

®

Dishwasher Cleaner will break up mineral

deposits, and remove hard water film and stains. You

can order citric acid GE Appliances kit #WD35X151

through GE Appliances Parts by calling 877-959-8688

or visiting GEApplianceparts.com. In Canada, call

1-800-661-1616. You can purchase Finish

®

Dishwasher

Cleaner at your local grocery store.

Stainless Steel Inner Door and Tub

The stainless steel used to make the dishwasher tub and

inner door provides the highest reliability available in a

GE Appliances dishwasher.

If the dishwasher tub or inner door should be scratched

or dented during normal use, they will not rust or

corrode. These surface blemishes will not affect their

function or durability.

Exterior Door Panel

Before cleaning the front panel, make sure you know

what type of panel you have. Refer to the last two letters

of your model number. You can locate your model

number on the left-hand tub wall just inside the door.

If your model number ends with BB, CC, WW, SA or

ES then you have a painted door panel. If your model

number ends with SS, then you have a Stainless Steel

door panel. If your model number ends with II, then you

have an Integrated door panel.

Follow the instructions below for cleaning the door panel

for your specific model.

Painted Door Panel (model numbers ending in BB–

black, CC–bisque, WW–white, SA-silver or ES-slate)

Use a clean, soft, lightly dampened cloth, then dry

thoroughly.

Do not use scouring pads or powered cleaners because

these products can scratch the finish.

Stainless Steel Door Panel (model numbers ending in SS)

For cleaning rust and tarnish, cleaners with oxalic acid

such as Bar Keepers Friend Soft Cleanser™ will remove

rust, tarnish and small blemishes. Use only a liquid

cleanser free of grit and rub in the direction of the brush

lines with a damp soft sponge. Do not use appliance wax

or polish on the stainless steel.

For other blemishes and marks, use Stainless Steel

Magic or a similar product using a clean soft cloth.

Do not use appliance wax, polish, bleach or products

containing chlorine on Stainless Steel. You can

order Stainless Steel Magic # WX10X29 through GE

Appliances Parts by calling 877.959.8688. In Canada,

call 1-800-661-1616.

Integrated Door Panel (model numbers ending in II)

This is a custom installed door panel, and you will need

to refer to the cabinet manufacturers recommendations

for proper cleaning.

16 49-55117

Care and cleaning

USING THE DISHWASHER

Filters

Inspect and clean the filters periodically. This should be done every other month or more depending on usage. If

there is a decrease in wash performance or dishes feel gritty, this is also an indication the filters need to be cleaned.

Protect Against Freezing

If your dishwasher is left in an unheated place during the

winter, ask a service technician to:

1

Turn off electrical power to the dishwasher. Remove

fuses or trip circuit breaker.

2

Turn off the water supply and disconnect the water inlet

line from the water valve.

3

Drain water from the water inlet line and water valve.

(Use a pan to catch the water.)

4

Reconnect the water inlet line to the water valve.

Does Your Dishwasher Have an Air Gap?

An air gap protects your dishwasher

against water backing up into it if a drain

clogs. The air gap is not a part of the

dishwasher. It is not covered by your

warranty. Not all plumbing codes require

air gaps, so you may not have one.

The air gap is easy to clean.

1

Turn off the dishwasher and lift off the air gap cover.

2

Remove the plastic cap under the cover and clean with a

toothpick.

3

Replace the cap and cover when the air gap is clean.

Check the air gap any

time your dishwasher

isn’t draining well.

Air gap

Ultra-Fine Filter

To clean the Ultra-Fine Filter, remove the bottom rack.

Twist the Ultra-Fine Filter counterclockwise and lift to

remove. Rinse filter with warm soapy water and use

a sponge to carefully remove any stubborn particles.

Scrubbing with scouring pads or brushes can damage

the filter. Once cleaned, replace the Ultra-Fine Filter, and

twist it clockwise to lock in place.

Fine Filter

To clean the Fine Filter (mesh plate), remove the bottom

rack. Remove the Ultra-Fine Filter.

Twist each of the two retaining posts located toward the

back bottom of the tub counterclockwise, and remove the

Fine Filter. Rinse filter with warm soapy water. Scouring

pads or brushes can scratch the filter surface but a soft

brush or sponge may be needed to remove stubborn

soils or calcium deposits caused by hard water. Once

cleaned, replace the Fine Filter and the Ultra-Fine Filter.

Twist the two retaining posts clockwise to lock in place.

The retaining posts can be a

choke hazard for small children if

removed from the dishwasher. Keep out of reach

of children.

WARNING

Fine

Filter

Spray

Arm

Retaining

Posts

Ultra-Fine

Filter

49-55117 17

Troubleshooting Tips... Before you call for service

TROUBLESHOOTING TIPS

Problem Possible Cause What To Do

Start status indicator

light flashing

The door was opened or the

cycle was interrupted.

Press the Start pad once and close the door within 4

seconds to start the dishwasher. Press the Start pad a

second time when the dishwasher is running only if you

wish to cancel the cycle.

Dishwasher BEEPS

once every minute

(on some models)

This is a reminder that your

dishwasher door has been left

open during operation. It will

continue beeping until you

press Start and close the door.

Press Start and close the door.

Beeping at the end

of the cycle (on

some models)

This is normal. Dishwasher

will beep twice at the end of

the cycle.

To turn off the double beep indicator (or re-activate it if

it was previously turned off), press the Heated Dry pad 5

times within 3 seconds. A triple beep will sound to indicate

the end-of-cycle beep option has been turned on or off.

Dishes and flatware

not clean

Ultra-Fine Filter or Fine

Filter is clogged

See the Care and Cleaning section.

Low inlet water temperature Make sure inlet water temperature is correct (see the

USING THE DISHWASHER section). Turn on the hot

water faucet nearest the dishwasher, let run until the water

temperature stops rising. Then start the dishwasher and

turn off the faucet. This ensures the entering water is hot.

Select Wash Temp Boost if available.

Water pressure is

temporarily low

Turn on a faucet. Is water coming out more slowly than usual?

If so, wait until pressure is normal before using your dishwasher.

Normal water pressure to the dishwasher should be 20-120 psi.

Air gap or disposer clogged Clean the air gap or flush the disposer.

High drain loop or air gap

not installed

Refer to the Installation Instructions for proper drain line

installation.

Improper rack loading Make sure large dishware does not block the detergent

dispenser or the wash arms. See the Loading section.

When large utensils are placed in the silverware basket,

do not mount the basket on the door (on some models).

Instead, mount basket on the lower rack.

Poor performing detergent Use a highly rated detergent such as Finish

®

Quantum

®

Automatic Dishwashing Detergent.

Spots and filming

on glasses and

flatware

Extremely hard water Use rinse agents such as Finish

®

Jet-Dry

®

Rinse Aid to

prevent spots and prevent new film build-up.

If water is extremely hard, a softener may be required.

Low inlet water temperature Make sure water temperature is at least 120°F (49°C).

Overloading or improper

loading of the dishwasher

Load dishwasher as shown in the Loading section.

Old or damp powder

detergent

Make sure detergent is fresh. Use a highly rated

detergent such as Finish

®

Quantum

®

Automatic

Dishwashing Detergent.

Rinse agent dispenser empty

Refill with rinse agent such as Finish

®

Jet-Dry

®

Rinse Aid.

Too little or low performing

detergent

Make sure you use the proper amount of highly rated

detergent.

Cloudiness on

glassware

Combination of soft water

and too much detergent

This is called etching and is permanent. To prevent this

from happening, use less detergent if you have soft water.

Wash glassware in the shortest cycle that will get it clean.

Low performing phosphate-

free detergent

See A white film on glassware, dishware and the

interior in this TROUBLESHOOTING section.

Water temperature entering

the dishwasher exceeds

150°F (66°C)

This could be etching. Lower the water heater

temperature.

18 49-55117

TROUBLESHOOTING TIPS

Troubleshooting Tips... Before you call for service

Problem Possible Cause What To Do

Suds in the tub Wrong detergent Use only automatic dishwasher detergents to avoid sudsing.

Finish

®

Quantum

®

Automatic Dishwashing Detergent

has been approved for use in all GE Appliances

dishwashers.

To remove suds from the tub, open the dishwasher and

let suds dissipate. Pump out water by pressing Start and

close the door. Wait 30 seconds. Open the door, press

and hold Start for 3 seconds, and close the door. Repeat

if necessary.

Rinse agent was spilled Always wipe up rinse agent spills immediately.

Detergent left in

dispenser cups

Dishes or utensils are

blocking the detergent cup

Reposition the dishes, so the water from the lower spray

arm can flush the detergent cup. See the Loading section.

Reposition the tall utensils or heavy silverware that may

be keeping the dispenser cup door from opening. See

the Loading section.

Black or gray marks

on dishes

Aluminum utensils have

rubbed against dishes

Remove marks with a mild, abrasive cleaner.

Dishes don’t dry Low inlet water temperature Make sure inlet water temperature is at least 120°F.

Select Heated Dry.

Use Wash Temp Boost.

Select a higher cycle, such as Wash Temp Sani,

Sanitize Temp or Heavy.

Rinse agent dispenser is

empty

Check the rinse agent dispenser and fill as required.

Cycle selection If using Light cycle which uses lower water temperature

and thus limited dry performance, switch to a different cycle.

Cycle completion Allow cycles to fully complete. See Long cycle times in

this Troubleshooting Tips section

Long cycle times Dishwasher washes by

alternating mid and lower

spray arms

Longer cycles are normal. For best wash and dry

performance, let cycle complete.

Soil level The turbidity sensor senses how much soil is on the

dishes. Heavy soiled dish loads will add more time to

the cycle. This is normal function. For best wash and dry

performance, allow cycle to complete.

Control panel

responded to inputs

but dishwasher

never filled with

water

Door may not be completely

closed

Make sure the door is firmly closed.

Water valve may be turned

off

Make sure water valve (usually located under the sink) is

turned on.

Flood float may be stuck Remove Ultra-Fine filter and lightly tap the piece under the

ultra fine filter that looks like a salt shaker. Replace the filter.

49-55117 19

Problem Possible Cause What To Do

Stained tub interior Some tomato-based foods

can cause reddish stains

Use of the Steam cycle (on some models) after adding

the dish to the load can decrease the level of staining.

Tea or coffee stains Remove the stain by hand, using a solution of 1/2 cup

bleach and 3 cups warm water. NOTE: Do not use

bleach on stainless steel inner door.

Before cleaning interior, wait at

least 20 minutes after a cycle for

the heating elements to cool down. Failure to do so

can result in burns.

CAUTION

An overall yellow or brown

film can be caused by iron

deposits in water

A special filter in the water supply line is the only way to

correct this problem. Contact a water softener company.

White film on inside

surface— hard water

minerals

GE Appliances recommends

Finish

®

Jet-Dry

®

Rinse Aid

to help prevent hard water mineral deposits from forming.

Run dishwasher with citric acid to remove mineral

deposits. Citric acid (Part number: WD35X151) can be

ordered through GE Appliances Parts. See back cover

for ordering information. Alternatively, purchase Finish

®

Dishwasher Cleaner and follow the directions on the

label.

Dishwasher won’t

run

Fuse is blown or circuit

breaker is tripped

Replace fuse or reset circuit breaker. Remove any other

appliances from the circuit.

Power is turned off In some installations, the power to the dishwasher is

provided through a wall switch, often located next to the

disposer switch. Make sure it is on.

Control panel is locked Unlock control panel. See the Getting started section.

Control panel lights

go off when you’re

setting controls

Time too long between

touching of selected

buttons

Each pad must be touched within 30 seconds of the

others. To relight, touch any pad again or open the door

and unlock (top control).

Water standing in

the bottom of the

tub

Air gap is clogged Clean the air gap. See the Care and Cleaning section.

High drain loop or air gap

not installed

Refer to the Installation Instructions for proper drain line

installation.

Water won’t pump

out of the tub

Drain is clogged If you have an air gap, clean it. See the Care and

Cleaning section.

If the dishwasher drains into a disposer, run disposer clear.

Check to see if your kitchen sink is draining well. If not,

you may need a plumber.

Troubleshooting Tips... Before you call for service

TROUBLESHOOTING TIPS

20 49-55117

TROUBLESHOOTING TIPS

Troubleshooting Tips... Before you call for service

Problem Possible Cause What To Do

Steam This is normal Warm, moist air comes through the vent during drying and

when water is being pumped out. This is necessary for drying.

Sanitized light does

not illuminate at the

end of the cycle

The door was opened and

the cycle was interrupted

during final rinse

Do not interrupt the cycle by opening the door during the

wash cycle.

The incoming water

temperature was too low

Raise the water heater temperature to between 120°F

and 150°F.

Noise Normal operating sounds:

Beeping at the end of the

cycle (on some models)

Detergent cup opening

Water entering dishwasher

Motor stops and starts at

various times during cycle

Spray arms start and stop

at various times

Drain pump sounds during

pump out

Drain pump starts and

stops several times during

each drain

These are all normal. No action is required.

Rattling dishes when the

spray arm rotates

Make sure dishes are properly loaded. See the Loading

section.

Rattling silverware against

door during wash

Tall utensils may be placed in the upper rack to avoid

bumping against inner door during wash cycle.

A white film on

glassware, dishware

and the interior

This problem is likely

caused by a low quality

phosphate-free dishwasher

detergent

To remove the white film, run your dishes through a

dishwasher cycle with citric acid. Use a WD35X151

citric acid kit found online. Otherwise, use Finish

®

Dishwasher Cleaner found at your local grocery store.

Pour the citric acid in the detergent cup and close the

cover. Place the filmed but otherwise clean glassware and

dishware in the dishwasher. Leave silverware and other

metal items out of the dishwasher. Turn the dishwasher on

and let it run through a complete cycle without detergent.

The glassware, dishware, and dishwasher should come out

film free. Alternatively, a vinegar rinse may be used. Pour 1

cup of vinegar into dishwasher just after the detergent cup

opens and let the dishwasher complete its cycle.

This may be repeated several times a year as needed.

The use of a rinse agent such as

Finish

®

Jet-Dry

®

Rinse Aid may help minimize a repeat build up of film.

Also, the use of a highly rated detergent such as Finish

®

Quantum

®

Automatic Dishwashing Detergent will help

prevent film build-up.

La page charge ...

GE GDT625PSJSS Le manuel du propriétaire

GE GDT625PSJSS Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents