GE Appliances JN327HBB Manuel utilisateur

JN327HBB
Marque
GE Appliances
Modèle
JN327HBB
Catégorie
Hottes
Taper
Manuel utilisateur
Range Hoods
GEAppliances.com
49-80589-1 08-09 JR
Safety Information . . . . . . . . 2, 3
Operating/Care and
Cleaning Instructions
Charcoal Filter . . . . . . . . . . . . . . . . . . . .5
Grease Filter . . . . . . . . . . . . . . . . . . . . .4
Hood Light . . . . . . . . . . . . . . . . . . . . . . .5
Hood Surfaces . . . . . . . . . . . . . . . . . . .5
Controls . . . . . . . . . . . . . . . . . . . . . . . . . .4
Installation
Instructions . . . . . . . . . . . . . . . .6–14
Consumer Support
Consumer Support . . . . .Back Cover
Warranty . . . . . . . . . . . . . . . . . . . . . . . 15
JV247*–Vent & Recirculation
options
JV248*–Vent & Recirculation
options
JN327–Recirculation only
JV338*–Vent options only
JV347*–Vent & Recirculation
options
JV348*–Vent & Recirculation
options
JV367*–Vent & Recirculation
options
RN328–Recirculation only
Owner’s Manual and
Installation Instructions
Write the model and serial numbers here:
Model # __________________________
Serial # __________________________
You can find them on a label on the
back wall of the hood.
*
Operating Instructions
Safety Instructions
Consumer Support Installation Instructions
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
READ AND SAVE THESE INSTRUCTIONS
SAFETY PRECAUTIONS
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING – TO REDUCE THE RISK OF
FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS,
O
BSERVE THE FOLLOWING:
A. Use this unit only in the manner intended
by the manufacturer. If you have questions,
contact the manufacturer.
B. Before servicing or cleaning unit, switch power off
at service panel and lock the service disconnecting
means to prevent power from being switched on
accidentally. When the service disconnecting
means cannot be locked, securely fasten a
prominent warning device, such as a tag, to
the service panel.
C. Do not use this unit with any solid-state speed
control device.
D. If using a cord connection kit, use only with range
hood cord-connection kit JXHC1 that has been
investigated and found acceptable for use with
this model range hood.
E. This unit must be grounded.
CAUTION – FOR GENERAL VENTILATING
USE ONLY. DO NOT USE TO EXHAUST HAZARDOUS OR
EXPLOSIVE MATERIALS AND VAPORS.
WARNING – TO REDUCE THE RISK OF
INJURY TO PERSONS IN THE EVENT OF A RANGE TOP
GREASE FIRE, OBSERVE THE FOLLOWING*:
A. SMOTHERFLAMES with a close-fitting lid, cookie
sheet or metal tray, then turn off the burner.
BE CAREFUL TO PREVENT BURNS.
If the flames do not go out immediately, EVACUATE
AND CALL THE FIRE DEPARTMENT.
B. NEVER PICK UP A FLAMING PAN—
You may be burned.
C. DO NOT USE WATER, including wet dishcloths or
towels—a violent steam explosion will result.
D. Use an extinguisher ONLY if:
1. You know you have a Class ABC extinguisher,
and you already know how to operate it.
2. The fire is small and contained in the area where
it started.
3. The fire department is being called.
4. You can fight the fire with your back to an exit.
* Based on “Kitchen Firesafety Tips” published by NFPA.
WARNING – TO REDUCE THE RISK
OF A RANGE TOP GREASE FIRE:
A. Never leave surface units unattended at high
settings. Boilovers cause smoking and greasy
spillovers that may ignite. Heat oils slowly on low
or medium settings.
B. Always turn hood ON when cooking on high
heat or when flambeing food (i.e. Crepes Suzette,
Cherries Jubilee, Peppercorn Beef Flambé).
C. Clean ventilating fans frequently. Grease should
not be allowed to accumulate on fan or filter.
D. Use proper pan size. Always use cookware
appropriate for the size of the surface element.
WARNING – TO REDUCE THE RISK
OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
A. Installation work and electrical wiring must be
done by qualified person(s) in accordance with
all applicable codes and standards, including
fire-rated construction.
B. Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of
fuel burning equipment to prevent back drafting.
Follow the heating equipment manufacturer’s
guideline and safety standards such as those
published by the National Fire Protection
Association (NFPA), the American Society for
Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE) and the local code authorities.
C. When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
D. Ducted fans must always be vented to the
outdoors.
WARNING – TO REDUCE THE RISK OF
FIRE AND TO PROPERLY EXHAUST AIR, BE SURE TO
DUCT AIR OUTSIDE—DO NOT VENT EXHAUST AIR
INTO SPACES WITHIN WALLS OR CEILINGS OR INTO
ATTICS, CRAWL SPACES OR GARAGES.
WARNING – TO REDUCE THE RISK OF
FIRE, USE ONLY METAL DUCTWORK.
■
Do not attempt to repair or replace any part of your
hood unless it is specifically recommended in this
guide. All other servicing should be referred to a
qualified technician.
2
Installation Instructions Consumer SupportSafety Instructions Operating Instructions
LISEZ ETSUIVEZ ATTENTIVEMENT CES INSTRUCTIONS.
LISEZ ET CONSERVEZ CES INSTRUCTIONS
PRÉCAUTIONS EN MATIÈRE DE SÉCURITÉ
INSTRUCTIONS DE SÉCURITÉ IMPORTANTES.
LISEZ TOUTES LES INSTRUCTIONS AVANT D’UTILISER.
AVERTISSEMENT – POUR
RÉDUIRE LE RISQUE D’INCENDIE, DE SECOUSSE
ÉLECTRIQUE OU DE BLESSURE CORPORELLE, OBSERVEZ
LES PRÉCAUTIONS SUIVANTES :
A. N’utilisez cet appareil que de la manière prévue par
le fabricant. Si vous avez des questions, appelez
le fabricant.
B. Avant de réparer ou de nettoyer votre appareil,
débranchez le courant au niveau du panneau
de service et verrouillez les mécanismes de
débranchement de service pour éviter tout
branchement accidentel au courant. Si vous ne pouvez
pas verrouiller les mécanismes de débranchement de
service, attachez soigneusement un avertissement bien
visible, comme une étiquette, au panneau de service.
C. N’utilisez jamais cet appareil avec un mécanisme
de réglage de la vitesse à semi-conducteurs.
D. Si vous utilisez l’ensemble de cordon de raccordement,
utilise seulement avec l’ensemble de cordon de
raccordement pour hotte JXHC1. Suite à un examen
technique, l’article JXHC1 s’est avéré compatible avec
ce modèle de hotte.
E. Cet appareil doit être bien mis à la terre.
ATTENTION – UNIQUEMENT À USAGE
DE VENTILATION GÉNÉRALE. N’UTILISEZ JAMAIS POUR
L’ÉCHAPPEMENT DE MATIÈRES ET DE VAPEURS
EXPLOSIVES
.
AVERTISSEMENT – POUR
RÉDUIRE LE RISQUE DE BLESSURE CORPORELLE SI DE
LA GRAISSE PREND FEU SUR LA SURFACE DE CUISSON
DE LA CUISINIÈRE, SUIVEZ LES INSTRUCTIONS
SUIVANTES* :
A. ÉTOUFFEZ LES FLAMMES avec un couvercle qui
convient, une tôle à biscuits ou un plateau en métal,
puis éteignez le brûleur. FAITES BIEN ATTENTION DE NE
PAS VOUS BRÛLER. Si les flammes ne s’éteignent pas
immédiatement, SORTEZ ET APPELEZ LES POMPIERS.
B. NE DÉPLACEZ JAMAIS UNE CASSEROLLE QUI FLAMBE –
Vous pouvez vous brûler.
C. N’UTILISEZ JAMAIS D’EAU, en particulier de serviette
ou de chiffon mouillé – il se produira une explosion
violente de vapeur brûlante.
D. N’UTILISEZ UN EXTINCTEUR que si :
1. Vous avez un extincteur de classe ABC et vous
savez comment l’utiliser;
2. Le feu est réduit et confiné à l’endroit où il a
commencé;
3. Vous avez déjà appelé les pompiers;
4. Vous combattez les flammes en tournant le dos
à une sortie.
* Basé sur l’ouvrage intitulé «Kitchen Fire Safety Tips»
publié par la NFPA.
AVERTISSEMENT – POUR
RÉDUIRE LE RISQUE D’UN FEU DE GRAISSE SUR
LA SURFACE DE CUISSON DE LA CUISINIÈRE :
A. Ne laissez jamais sans surveillance les unités de
cuisson de surface à une température élevée. Le
bouillonnement occasionne des débordements
fumants et graisseux qui peuvent prendre feu.
Chauffez à feu doux les substances huileuses,
avec un réglage bas ou moyen.
B. ALLUMEZ toujours la hotte en cas de cuisson à
feu élevé ou lorsque vous faites flamber des aliments
(par exemple, crêpes Suzette, cerises jubilées, bœuf
au poivre flambé).
C. Nettoyez les mécanismes de ventilation fréquemment.
Il ne faut pas permettre une accumulation de graisse
sur le ventilateur ou sur le filtre.
D. Utilisez une casserole de bonne taille. Utilisez toujours
un ustensile de cuisine qui convienne au diamètre
de l’élément de cuisson.
AVERTISSEMENT – POUR
RÉDUIRE LE RISQUE D’INCENDIE, DE SECOUSSE
ÉLECTRIQUE OU DE BLESSURE CORPORELLE, OBSERVEZ
LES PRÉCAUTIONS SUIVANTES :
A. Vous devez faire exécuter tous les travaux d’installation
et de câblage électrique par une personne qualifiée,
conformément à tous les codes et les normes en
vigueur, en particulier ceux de construction relatifs
aux incendies.
B. Vous devez assez d’air pour avoir une bonne
combustion et permettre l’évacuation des gaz par le
conduit de cheminée du matériel de combustion du
carburant, afin d’éviter tout retour d’air. Suivez les
directives du fabricant de matériel de combustion
et les normes de sécurité comme celles publiées
par la National Fire Protection Association (NFPA),
l’American Society for Heating, Refrigeration and
Air Conditioning Engineers (ASHRAE), ainsi que les
modalités des codes locaux.
C. Si vous faites un trou ou une ouverture dans un mur
ou un plafond, n’endommagez pas les fils électriques
et les autres installations cachées de service public.
D. Vous devez toujours alimenter les ventilateurs dans
les conduits en air en provenance de l’extérieur.
AVERTISSEMENT – POUR
RÉDUIRE LE RISQUE D’INCENDIE ET ÉVACUER
ADÉQUATEMENT L’AIR, ASSUREZ-VOUS DE FAIRE
DÉBOUCHER LA CONDUITE D’AIR À L’EXTÉRIEUR—
NE VENTILEZ PAS L’AIR ÉVACUÉ DANS DES ESPACES
COMPRIS À L’INTÉRIEUR DE MURS, D’UN PLAFOND,
D’UN GRENIER, D’UN VIDE SANITAIRE OU D’UN GARAGE.
AVERTISSEMENT – POUR
RÉDUIRE LE RISQUE D’INCENDIE, N’UTILISEZ QUE
DES CONDUITS EN MÉTAL.
■
N’essayez jamais de remplacer ou de réparer un
élément de votre hotte si le présent manuel ne le
recommande pas expressément. Tout autre entretien
doit être effectué par un technicien qualifié.
3
Operating Instructions Safety Instructions
Consumer Support Installation Instructions
Using the hood controls.
Throughout this manual, features and appearance may vary from your model.
FAN Control
Turn to HI, MED or LO as needed.
Continuous use of the fan system while cooking
helps keep the kitchen comfortable and less humid.
It also reduces cooking odors and soiling moisture
that create a frequent need for cleaning.
LIGHT Control
Turn to ON while cooking or to NITE for use as
a night light.
LIGHT Control
Press the pad at the top to turn the light ON.
FAN Control
Press the pad at the top to turn the fan on HI and at
the bottom to turn it on LO. The center position is OFF.
Continuous use of the fan system while cooking
helps keep the kitchen comfortable and less humid.
It also reduces cooking odors and soiling moisture
that create a frequent need for cleaning.
Control Knobs (on some models)
Care and cleaning of the vent hood.
Be sure electrical power is off and all surfaces are cool before cleaning or servicing any part of the
vent hood.
The efficiency of your hood
depends on a clean filter. Frequency
of cleaning depends on hood use
and the type of cooking you do.
However, the grease filter should
be cleaned at least once a month.
To remove:
Pull down on the center of the front
edge of the filter. The filter will then
slip out of the retaining tabs on the
back.
To replace:
Slip the back edge of the filter into
the retaining tabs and push the
front edge up until it snaps into
place.
To clean:
Soak and then agitate it in a hot
water and detergent solution. Light
brushing can be used to remove
embedded dirt. Rinse, shake and
let it dry before replacing.
NEVER OPERATE THE HOOD
WITHOUT THE FILTER IN PLACE.
With careful handling, the metal
filter will last for years. If a new
replacement filter becomes
necessary, order the part from
your dealer. Order genuine GE
part number WB02X8391.
Reusable Metal Grease Filter—Ducted Installations Only
4
Switch Pad Controls (on some models)
Grease filter
LO HI
MED NITE
OFF
OFF
ON
LO
OFF
HI
OFF
ON
Installation Instructions
Consumer Support
Safety Instructions Operating Instructions
Do not use steel-wool pads or other
abrasive cleaners. They will scratch
the surface.
Clean grease-laden surfaces of the hood
frequently. To clean the hood surface, use
a hot, damp cloth with a mild detergent
suitable for painted surfaces. About one
tablespoon of ammonia may be added to
the water. Use a clean, hot, damp cloth to
remove soap. Dry with a dry, clean cloth.
NOTE: When cleaning, take care not to
come in contact with filters and other
non-enameled surfaces.
CAUTION:When cleaning
the hood surfaces, be certain that you do
not touch the light bulb with moist hands
or cloth. A warm or hot light bulb may
break if touched with a moist surface.
Always let the light bulb cool completely
before cleaning around it.
Painted Surfaces
(on some models)
CAUTION:Let the light bulb
cool completely before removing. A
warm or hot bulb may break if touched
with a moist cloth or hand.
Remove the bulb and replace it with
a type A15 incandescent light bulb with
an ordinary screw base, not more than
60 Watts, or a type A17 or T2 Compact
Fluorescent (CFL) light bulb with an
ordinary screw base, not more than
13 Watts. NOTE: Use only incandescent
bulbs in models RN328, JN327 and JV338.
IMPORTANT: For installation, handling
and disposal precautions, refer to the
fluorescent bulb packaging literature.
To remove the light cover
(on some models):
• Press the sides with two fingers until
the side prongs are released.
• Lift the light cover and slide it toward
you in one motion.
To replace the light cover:
• Insert the prong located at the end
of the cover into the top opening.
• Gently push the cover up and press the
sides to fit the side prongs into the side
openings.
• Release and the cover will lock in position.
Hood Light
T
he charcoal filter cannot be cleaned.
It must be replaced. Order filter no.
WB02X10700. Replacement filters
can be ordered from your GE supplier.
If the hood is not vented to the outside,
the air will be recirculated through a
disposable charcoal filter that helps
remove smoke and odors.
The charcoal filter should be replaced after
6 to 12 months (depending on hood usage).
T
o remove:
Pull down on the center of the front edge
of the filter. The filter will then slip out of
the retaining tabs on the back.
To replace:
Slip the back edge of the filter into the
retaining tabs and push the front edge
up until it snaps into place.
Charcoal Filter—Recirculating Installations Only
Replaceable charcoal filter
5
NOTE: DO NOT rinse, or put charcoal
filters in an automatic dishwasher.
Light cover
Do not use a steel-wool pad; it will
scratch the surface.
To clean the stainless steel surface, use
warm sudsy water or a stainless steel
cleaner or polish. Always wipe the surface
in the direction of the grain. Follow the
cleaner instructions for cleaning the
stainless steel surface.
To inquire about purchasing stainless steel
appliance cleaner or polish, or to find the
location of a dealer nearest you, please
call our toll-free number:
National Parts Center
800.626.2002
GEAppliances.com
Stainless Steel Surfaces
(on some models)
When using an energy saving bulb in your GE hood
make sure you use either:
GE Long Life Energy Smart
™
Spiral
®
T2
Product Code: 85383
Description: FLE13HT2/2/SW/CD
or
GE Long Life Energy Smart
™
A17
Product Code: 47486
Description: FLE11/2/A17XL/CD
Available at www.gelighting.com
BEFORE YOU BEGIN
6
Installation Range Hood
Instructions
Read these instructions completely and carefully.
•
IMPORTANT – Save these instructions
for local inspector’s use.
•
IMPORTANT – Observe all governing
codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these instructions
for future reference.
• Skill level – Installation of this appliance requires
basic mechanical and electrical skills.
• Completion time – 30 minutes–3 hours
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not
covered under the Warranty.
NOTE: Read the ductwork sections only if you do not
have existing ductwork. If you have existing ductwork,
skip to the “Damage” section and proceed.
WARNING – TO REDUCE THE RISK OF FIRE AND
TO PROPERLY EXHAUST AIR, BE SURE TO DUCT AIR OUTSIDE—
DO NOT VENT EXHAUST AIR INTO SPACES WITHIN WALLS OR
CEILINGS OR INTO ATTICS, CRAWL SPACES OR GARAGES.
The venting system must exhaust to the outside.
This hood can be vented vertically through upper cabinets
or horizontally through an outside wall. Ductwork is not
included.
Exhaust connection:
The hood exhaust has been designed to mate with
standard 3
1
⁄4″ x 10″ rectangular ducting or 7″ diameter
round ducting.
If a 6″ round duct is required, a rectangular-to-round
transition adaptor must be used*. Do not use less than
a 6″ diameter duct.
Maximum duct length:
For satisfactory air movement, the total duct length
of a 3
1
⁄4″ x 10″ rectangular, 6″ or 7″ diameter round
duct should not exceed 65 equivalent feet. See the
WORKSHEET–CALCULATE TOTAL EQUIVALENT
DUCTWORK LENGTH section.
NOTE: It is important that ducting be installed using
the most direct route and with as few elbows as possible.
This ensures clear venting of exhaust and helps prevent
blockages. Also, make sure dampers swing freely and
nothing is blocking the ducts.
Elbows, transitions, wall and roofcaps, etc.,
present additional resistance to airflow and are equivalent
to a section of straight duct longer than their actual
physical size. When calculating the total duct length, add
the equivalent lengths of all transitions and adaptors plus
the length of all straight duct sections. The charts on the
following pages show you how to calculate total equivalent
ductwork length using the approximate feet of equivalent
length of some typical ducts.
* IMPORTANT: If a rectangular-to-round
transition adaptor is used, the bottom
corners of the damper will have to be
cut to fit, using the tin snips, in order
to allow free movement of the damper.
Equivalent lengths of duct pieces
are based on actual tests and reflect
requirements for good venting
performance with any hood.
DUCTWORK REQUIREMENTS
WARNING – Before beginning the
installation, switch power off at service panel and
lock the service disconnecting means to prevent power
from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten
a prominent warning device, such as a tag, to the
service panel.
FOR YOUR SAFETY:
Questions? Call 800.GE.CARES (800.432.2737) or visit our Website at: GEAppliances.com
An optional Power Cord Connection Kit, model JXHC1,
is available at extra cost from your GE supplier for
installation using a standard 3-prong, grounded wall
outlet. Follow the Installation Instructions packed with
the kit to connect the power cord to the range hood.
OPTIONAL POWER CORD KIT JXHC1
7
DUCT EQUIVALENT NUMBER
PIECES LENGTH x USED = TOTAL
3
1
⁄4″x 10″ 1 Ft. x ( ) = Ft.
Rect.,
straight
7″ Round, 1 Ft. x ( ) = Ft.
straight
6″ Round, 1 Ft. x ( ) = Ft.
straight
3
1
⁄4″x 10″ 14 Ft. x ( ) = Ft.
Rect. 90°
elbow
3
1
⁄4″x 10″ 8 Ft. x ( ) = Ft.
Rect. 45°
elbow
3
1
⁄4″x 10″ 33 Ft. x ( ) = Ft.
Rect. 90°
flat elbow
3
1
⁄4″x 10″ 24 Ft. x ( ) = Ft.
Rect.
(18 ft. w/o
wall cap
damper)
x ( ) = Ft.
with
damper
3
1
⁄4″x 10″ 2 Ft. x ( ) = Ft.
Rect. to
6″ round
transition
3
1
⁄4″x 10″ 4 Ft. x ( ) = Ft.
Rect. to
6″ round
transition
90° elbow
6″ Round, 25 Ft. x ( ) = Ft.
90° elbow
6″ Round, 16 Ft. x ( ) = Ft.
45° elbow
Subtotal column 1 = Ft.
WORKSHEET—CALCULATE TOTAL EQUIVALENT DUCTWORK LENGTH
DUCT EQUIVALENT NUMBER
PIECES LENGTH x USED = TOTAL
6″Round 53 Ft. x ( ) = Ft.
wall cap
(39 ft. w/o
with
damper)
x ( ) = Ft.
damper
6″ Round 72 Ft. x ( ) = Ft.
roof cap
6″ Round 3 Ft. x ( ) = Ft.
to
3
1
⁄4″x 10″
rect.
transition
6″ Round 9 Ft. x ( ) = Ft.
to
3
1
⁄4″x 10″
rect.
transition
90° elbow
7″ Round, 14 Ft. x ( ) = Ft.
90° elbow
7″ Round, 9 Ft. x ( ) = Ft.
45° elbow
7″ Round 28 Ft. x ( ) = Ft.
wall cap (
21 ft. w/o
with
damper)
x ( ) = Ft.
damper
7″ Round 39 Ft. x ( ) = Ft.
roof cap
7″ Round 1 Ft. x ( ) = Ft.
to
3
1
⁄4″x 10″
rect.
transition
7″ Round 5 Ft. x ( ) = Ft.
to
3
1
⁄4″x 10″
rect.
transition,
90° elbow
Subtotal column 2 = Ft.
Subtotal column 1 = Ft.
Total ductwork = Ft.
Installation Instructions
MAXIMUM DUCT LENGTH: For satisfactory air movement,
the total duct length of a 3
1
⁄4″ x 10″ rectangular, 7″ diameter
round duct should not exceed 65 equivalent feet.
PART QUANTITY
Grease Filter only (JV338) 1
Charcoal Filter only 1
(JN327 and RN328)
Grease Filter and Charcoal Filter 2
(JV24X, JV347, JV348 and JV367)
Mounting Screws 4
(8 - 18″ x 3/4″ Phillips pan head)
Exhaust Adaptor 1
(for 3
1
⁄4″ x 10″ rect. venting)
Exhaust Adaptor Screw 1
(8 - 18″ x 3/8″ Phillips pan head
or hex head)
8
•
If the unit is damaged in shipment, return the unit to the
store in which it was bought for repair or replacement.
•
If the unit is damaged by the customer, repair or
replacement is the responsibility of the customer.
• If the unit is damaged by the installer (if other than
the customer), repair or replacement must be made
by arrangement between customer and installer.
DAMAGE – SHIPMENT/INSTALLATION
PARTS INCLUDED
MOUNTING SPACE
NOTES:
• Hood width may be greater than the width of the range
or cooktop, but it may not be smaller.
• Ensure the range or cooktop is installed per
manufacturer’s installation instructions.
• If you are going to vent your range hood to the outside,
see the “Ducting Requirements” section for exhaust duct
preparation.
66″ or more
from the floor
to the top of
the hood
2
4
″
, 3
0
″
o
r 3
6″ to
ma
tch co
o
kto
p wid
th
30″
min.
Bottom edge of
cabinet needs
to be 30″ or
more from
the cooking
surface
Flat-blade and Phillips
screwdrivers
Pencil
Metal snips
(in some
applications)
Electric drill
Saw (saber or keyhole)
Duct tape
Pliers
Level
Caulking
Tape measure
TOOLS YOU WILL NEED
1/4″ pivoting
hex socket
Flashlight
Wire stripper
1/4″ Nutdriver
Installation Instructions
9
Outside top exhaust
(Vertical duct–3
1
⁄4″ x 10″ Rectangular)
Outside rear exhaust
(Horizontal duct–3
1
⁄4″ x 10″ Rectangular)
Outside top exhaust
(Vertical duct–7″ Round)
A
C
B
Recirculating
(non-vented/ductless)
D
Installation Instructions
CHOOSE VENT OPTION
Determine the vent option that your installation will
require and that is available for your model from the
below choices.
1
IMPORTANT: If the hood is to be installed in a
recirculating, non-vented, ductless manner, do not
knock out any vent openings in the hood. Only an
e
lectrical access hole will be knocked out of the hood.
JV338
JV247
JV248
JV347
JV348
JV367
JV338
JV247
JV248
JV347
JV348
JV367
JV338
JV247
JV248
JV347
JV348
JV367
JN327
RN328
JV247
JV248
JV347
JV348
JV367
10
REMOVE EXHAUST ADAPTOR
If exhausting/venting using the 3
1
⁄4″ x 10″ rectangular
duct—optional for JV247, JV248, JV338, JV347, JV348
a
nd JV367 models only:
Remove the exhaust adaptor from the inside of the hood.
Set it aside along with its mounting screws.
3
1
⁄4″ x 10″
rectangular
exhaust
adaptor
and screws
REMOVE FILTER
Remove the shipping tape holding the metal grease
filter in place. Pull down on the center of the front edge
of the filter. The filter will then slip out of the retaining
tabs on the back.
REVERSE THE BAFFLE FOR DUCTED
INSTALLATIONS ONLY
(JV247, JV248,
JV347, JV348 and JV367 models)
If the hood is to be recirculated, skip to the next step.
Remove the baffle from the top of the hood. Reinstall
the baffle so the short side marked “VENTED” is visible.
The long side of the baffle should be inside the hood.
REMOVE WIRING COVER
Remove the wiring cover from inside the hood.
Set the cover and its mounting screws aside.
Wiring
cover
REMOVE WIRING KNOCKOUT
Remove either the top or the back wiring knockout as
needed and install an approved strain relief clamp.
Strain relief
clamp
2
3
4
5
6
Metal grease filter
Installation Instructions
Back knockout
Top knockout
“VENTED” is visible
Strain relief
clamp
REMOVE DUCT KNOCKOUT
If recirculating, non-vented ductless (JN327 and RN328,
and optional for JV247, JV248, JV347, JV348 and JV367
models only), skip to Step 11 D and proceed.
Using a flat-blade screwdriver, remove the appropriate
duct knockout from the top or back of the hood.
3
1
⁄4″ x 10″ Rectangular
vertical discharge.
Remove top rectangular
duct knockout only.
7″ Round vertical
discharge. Remove circular
duct knockout only.
3
1
⁄4″ x 10″ Rectangular
horizontal discharge. Remove
rear rectangular duct knockout only.
7
11
FOR 3
1
⁄4″ X 10″ RECTANGULAR
DUCTED DISCHARGE INSTALLATIONS
ONLY:
A
ttach exhaust adaptor/damper over the appropriate
knockout opening (for vertical or horizontal, depending
on installation) with two exhaust adaptor screws. Make
sure damper pivot is nearest to top/back edge of hood.
Remove tape from damper flap.
Tape
Top/back edge
Exhaust adaptor/damper
(vertical discharge position)
Pivot
(depending on
installation)
FOR 7″ ROUND VERTICAL DUCTED
DISCHARGE INSTALLATIONS ONLY:
Bend up the duct alignment ears in preparation for
later attachment of the 7″ duct.
8
9
Installation Instructions
Exhaust adaptor/damper
(horizontal discharge position)
Attachment ear tabs
FOR RECESSED-BOTTOM CABINETS
ONLY
10
W
ood shims
(
minimum thickness
3/8″)
• If the cabinets have front, side or back trim, make
2 wood shims a minimum of 3/8″ thick and cut to
fit the width of the inner recessed cabinet bottom.
Attach them to the cabinet bottom recess on both
sides. See Step 11 for marking locations.
12
D.
Recirculating (non-vented ductless–
JN327 and RN328, and optional on JV247,
JV248, JV347, JV348 and JV367 models only)
• Use the hood as a template and mark the locations
on the cabinet for the electrical wiring and keyhole
screw slots.
• Since the hood is to be recirculated (not to be vented
outside), do not cut out any vent openings in the wall
or cabinet bottom.
Installation Instructions
Wood shims
(recessed-bottom cabinets only–shims must be a
minimum of 3/8″ thick and cut to fit the width
of the inner recessed cabinet bottom)
Cabinet front
Center line
Electrical access hole
(in wall)
Hood mounting screws (4)
Cabinet
bottom
10
3
⁄4″ (24″ hood)
13
3
⁄4″ (30″ hood)
16
3
⁄4″ (36″ hood)
1
1
⁄4″
1
⁄2″
3
3
⁄4″
5
1
⁄4″
5
1
⁄4″
7
3
⁄4″
10
3
⁄4″ (24″ hood)
13
3
⁄4″ (30″ hood)
16
3
⁄4″ (36″ hood)
C.
Outside rear exhaust
(Horizontal duct–3
1
⁄4
″
x 10
″
Rectangular)
• Use the diagram or the hood as a template and
mark the locations on the cabinet for ductwork,
electrical wiring and keyhole screw slots.
RUN WIRES
Run the electrical wires through the wall or
cabinet according to National Electrical Code
and applicable local codes.
NOTE: DO NOT turn the power on until installation
is complete.
13
CUT HOLES
Cut holes at marked locations for duct and electrical
wiring. For the vertical duct, cut out 3/4″ extra toward
the front of the cabinet so you can move the duct
freely when installing the hood. It may also ease
installation by cutting the hole 10
1
⁄2″ instead of 10″.
12
MARK HOLES
S
elect the vent option that your installation will require
and proceed to that section:
Hood mounting screws (4)
10
3
⁄4″ (24″ hood)
13
3
⁄4″ (30″ hood)
16
3
⁄4″ (36″ hood)
10
3
⁄4″ (24″ hood)
13
3
⁄4″ (30″ hood)
16
3
⁄4″ (36″ hood)
Cabinet front
Center
line
Electrical access hole
(in cabinet bottom)
Wood shims
(recessed-bottom
cabinets only–shims
must be a minimum of
3/8″ thick and cut to fit
the width of the inner
recessed cabinet bottom)
9
5
⁄8″
1
3
⁄8″
1
1
⁄4″
7
3
⁄4″
3
3
⁄4″
1
⁄2″
A.
Outside top exhaust
(Vertical duct–3
1
⁄4
″
x 10
″
Rectangular)
• Use the diagram or the hood as a template and mark
the locations on the cabinet for ductwork, electrical
wiring and keyhole screw slots.
B. Outside
top exhaust (Vertical duct–7″ Round)
• Use the diagram or the hood as a template and
mark the locations on the cabinet for ductwork,
electrical wiring and keyhole screw slots.
Hood mounting screws (4)
10
3
⁄4″ (24″ hood)
13
3
⁄4″ (30″ hood)
16
3
⁄4″ (36″ hood)
10
3
⁄4″ (24″ hood)
13
3
⁄4″ (30″ hood)
16
3
⁄4″ (36″ hood)
Cabinet front
Center
line
Electrical access
hole (in cabinet bottom)
Wood shims (recessed-bottom
cabinets only–shims must be a
minimum of 3/8″ thick and cut
to fit the width of the inner
recessed cabinet bottom)
Access
hole for 7″
round duct
9
5
⁄8″
1
3
⁄8″
1
1
⁄4″
7
3
⁄4″
5
3
⁄4″
Cabinet
bottom
11
5
1
⁄4″
5
1
⁄4″
Cabinet Bottom
V
ertical duct
access hole
8″ DIA.
HOLE
H
orizontal duct
a
ccess hole
13
Installation Instructions
SCREW IN PART WAY
Drive a mounting screw (from the hardware packet)
part way into each center of the narrow neck of the
keyhole slots marked on the cabinet bottom.
OPTIONAL POWER CORD
KIT JXHC1
An optional Power Cord Connection Kit, model
JXHC1, is available at extra cost from your GE
supplier for installation using a standard 3-prong,
grounded wall outlet. Follow the Installation
Instructions packed with the kit to connect the
power cord to the range hood.
14
15
NOTE: If using optional Power Cord Kit JXHC1, feed
the power cord through the hole in the top cabinet
while raising the hood. Loop any excess length of
cord and tie away with a suitable tape or tie.
Cabinet
7
3
⁄4″
3-prong
wall outlet
(if using cord
connection)
1
1
⁄4″
1
3
⁄4″ dia. clearance hole
for optional power
supply location
C
L
FEED IN WIRES
Lift the hood into position and feed the house wiring
through the wiring knockout.
16
SECURE HOOD
Slide the hood back against the wall. Tighten the
mounting screws. Be sure the screw heads are in
the narrow neck of the keyhole slot.
Keyhole (4)
M
ounting
s
crew (4)
NOTE: DO NOT PUSH ON THE FAN BLADE. Pushing on
the blade may cause it to interfere with other hood
parts.
17
CONNECT DUCTWORK TO HOOD
(Ducted installations only)
On 7″ round installations, attach the 7″ duct
with sheet metal screws through the holes in
the alignment ears.
Use duct tape to make joints secure and airtight.
Duct tape
18
Attachment ear tabs
7″ round duct
14
FOLLOW ELECTRICAL CODE
Complete the electrical wiring according to National
Electrical Code and local codes.
NOTE: This hood must be permanently grounded.
Connect house wiring (120 VAC) to hood wiring.
20
INSTALL LIGHT BULB
NOTE: A light bulb is not shipped with the hood.
Obtain one locally. Purchase and install a type A15
incandescent light bulb with an ordinary screw base,
not more than 60 Watts, or a type A17 or T2
Compact Fluorescent (CFL) light bulb with an ordinary
screw base, not more than 13 Watts.
NOTE: Use only
incandescent bulbs in models RN328, JN327 and JV338.
IMPORTANT: For installation, handling and disposal precautions,
refer to the fluorescent bulb packaging literature.
When using an energy saving bulb in your GE hood, make sure you use
either:
19
Installation Instructions
TROUBLESHOOTING CHECKLIST
If the hood seems to be operating at high speed when
the control is not set on high, or if ventilation seems
inadequate, check the following:
❏ Knockouts not removed from hood.
❏ Damper blade not opening.
❏ Reduced airflow because the duct is too small or
the duct length is too long.
❏ The duct is blocked.
❏ Undersized or restrictive wall or roof cap.
If the hood seems to make excessive noise:
❏ Fan may be hitting the filter. Turn off the fan and
remove the filter. Bend the filter down slightly in the
center (into a dome shape) to allow fan clearance.
Reinstall and adjust as needed.
The fan does not work but the lights do:
❏ Switch power off at the service panel and lock the
service disconnecting means to prevent power from
being switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag,
to the service panel.
❏ Check the wiring connections. See the CONNECT
WIRING section in these Installation Instructions.
REPLACE WIRING COVER
CONNECT WIRING
Connect house black to hood black wire, house white
to hood white wire and house ground under green
ground screw. Securely tighten the strain relief clamp
onto the house wiring.
Green ground screw
21
22
23
REPLACE FILTER
Make sure fan blade turns freely and replace the filter.
NOTE: Install the metal grease filter if ducted or the
charcoal filter if recirculated.
WARNING:IMPROPER CONNECTION OF
ALUMINUM HOUSE WIRING TO THESE COPPER LEADS
CAN RESULT IN A SERIOUS PROBLEM. USE ONLY
CONNECTORS DESIGNED FOR JOINING COPPER TO
ALUMINUM AND FOLLOW THE MANUFACTURER’S
RECOMMENDED PROCEDURE CLOSELY.
The installation is complete. Turn on power at service
panel, and test for proper operation.
Wiring cover
Metal grease filter or charcoal filter
GE Long Life Energy
Smart
™
Spiral
®
T2
Product Code: 85383
Description:
FLE13HT2/2/SW/CD
GE Long Life Energy
Smart
™
A17
Product Code: 47486
Description:
FLE11/2/A17XL/CD
Available at
www.gelighting.com
or
GE Range Hood Warranty.
For The Period Of: GE Will Replace:
One Year Any part of the range hood which fails due to a defect in materials or workmanship.
From the date of the During this limited one-year warranty, GE will also provide, free of charge, all labor and
original purchase in-home service to replace the defective part.
■ Service trips to your home to teach you how to use
the product.
■ Improper installation, delivery or maintenance.
■ Failure of the product if it is abused, misused, or
used for other than the intended purpose or used
commercially.
■ Replacement of house fuses or resetting of circuit
breakers.
■ Damage to the product caused by accident, fire, floods
or acts of God.
■ Incidental or consequential damage caused by possible
defects with this appliance.
■ Damage caused after delivery.
■ Product not accessible to provide required service.
What GE Will Not Cover:
This warranty is extended to the original purchaser and any succeeding owner for products purchased for
home use within the USA. If the product is located in an area where service by a GE Authorized Servicer is not
available, you may be responsible for a trip charge or you may be required to bring the product to an Authorized GE
Service Location for service. In Alaska, the warranty excludes the cost of shipping or service calls to your home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty
gives you specific legal rights, and you may also have other rights which vary from state to state. To know
what your legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.
Warrantor: General Electric Company. Louisville, KY 40225
Installation Instructions
Consumer Support
Safety Instructions Operating Instructions
15
All warranty service provided by our Factory Service Centers, or
an authorized Customer Care
®
technician. To schedule service,
visit us on-line at GEAppliances.com, or call 800.GE.CARES
(800.432.2737). Please have serial number and model number
available when calling for service.
Staple your receipt here.
P
roof of the original purchase
date is needed to obtain service
under the warranty.
EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided
in this Limited Warranty. Any implied warranties, including the implied warranties of merchantability
or fitness for a particular purpose, are limited to one year or the shortest period allowed by law.
Printed in China
Consumer Support.
GE Appliances Website
GEAppliances.com
Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day,
any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals,
o
rder parts or even schedule service on-line.
Schedule Service GEAppliances.com
Expert GE repair service is only one step away from your door. Get on-line and schedule your service at
your convenience any day of the year! Or call 800.GE.CARES (800.432.2737) during normal business hours.
Real Life Design Studio GEAppliances.com
GE supports the Universal Design concept—products, services and environments that can be used by
people of all ages, sizes and capabilities. We recognize the need to design for a wide range of physical and
mental abilities and impairments. For details of GE’s Universal Design applications, including kitchen design ideas
for people with disabilities, check out our Website today. For the hearing impaired, please call 800.TDD.GEAC
(800.833.4322).
Extended Warranties GEAppliances.com
Purchase a GE extended warranty and learn about special discounts that are available while your warranty
is still in effect. You can purchase it on-line anytime, or call 800.626.2224 during normal business hours.
GE Consumer Home Services will still be there after your warranty expires.
Parts and Accessories GEAppliances.com
Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes
(VISA, MasterCard and Discover cards are accepted). Order on-line today, 24 hours every day or
by phone at 800.626.2002 during normal business hours.
Instructions contained in this manual cover procedures to be performed by any user. Other servicing
generally should be referred to qualified service personnel. Caution must be exercised, since improper
servicing may cause unsafe operation.
Contact Us GEAppliances.com
If you are not satisfied with the service you receive from GE, contact us on our Website with all the details
including your phone number, or write to: General Manager, Customer Relations
GE Appliances, Appliance Park
Louisville, KY 40225
Register Your Appliance GEAppliances.com
Register your new appliance on-line—at your convenience! Timely product registration will allow for
enhanced communication and prompt service under the terms of your warranty, should the need arise.
You may also mail in the pre-printed registration card included in the packing material.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

GE Appliances JN327HBB Manuel utilisateur

JN327HBB
Marque
GE Appliances
Modèle
JN327HBB
Catégorie
Hottes
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents