Yamaha DBR15/DBR12/DBR10 Manuel utilisateur

Marque: Yamaha

Modèle: DBR15/DBR12/DBR10

Catégorie: Amplificateurs audio

Taper: Manuel utilisateur

Floor monitor system

This system is suitable for a performer’s monitoring system. For use as a vocal monitor, set the [D-CONTOUR] switch to [MONITOR].

If necessary, you can additionally connect up to four speakers in parallel. In this case we recommend that the signal is input to CH1 and the output switch is set to [CH1 THRU].

To next speaker

Mixer

Set to [CH1 THRU]Set to [CH1 THRU]

In order to take full advantage of the DBR series’ (referred to in this manual as DBR) superior functionality

and enjoy years of trouble-free use, please read this manual before you begin using the product. After you

have read the manual, keep it in a safe place for reference when needed.

• Please read the PRECAUTIONS on the reverse side of this manual before use.

• This manual uses example illustrations taken from the DBR12 if not otherwise speciﬁed.

• The illustrations as shown in this manual are for instructional purposes only, and may appear somewhat

different from those on your device.

• The company names and product names used in this manual are the trademarks or registered

trademarks of their respective companies.

Features

• FIR-X tuning™

Our proprietary sound-processing technology utilizing a linear-phase FIR ﬁlter delivers excellent sound quality

with high resolution and a smooth frequency response that is unaffected by phase interference near the

crossover point.

• D-CONTOUR (Dynamic CONTOUR)

D-CONTOUR optimizes the level of each frequency range according to the application to be used or the

listener’s preferences. There are two modes: an FOH/MAIN mode for use as a main speaker, and a MONITOR

mode for use as a ﬂoor monitor.

• Simple mixing function

The DBR features simple mixing functionality, enabling you to select either a direct output of channel 1 (CH1)

(parallel connection) or a mixed output of CH1 and CH2.

• Various input/output connectors

The comprehensive set of connectors—including XLR for a mixer, phone for a musical instrument, and RCA-

pin for an MP3 player—provides maximum ﬂexibility in use with a wide variety of applications.

• Light weight, high power

A newly developed power supply and ampliﬁer has enabled compact size and light weight, as well as

powerful output.

• Advanced protection functionality

DSP-controlled advanced protection functionality promotes optimum reliability even in challenging

environments.

Included Accessories

• AC power cord

• Technical Speciﬁcations (English only): includes speciﬁcations, block diagram, and dimensions.

• Owner’s manual (this leaﬂet)

ZJ41540

POWERED SPEAKER SYSTEM

DBR series

Owner’s Manual

Simple system with a single DBR

This example illustrates the system when connecting directly to a microphone, musical instrument, or

background music source without using a mixer.

Main application: small-sized live venue, presentations, restaurants

Note

For CH2, inputs to the combo jack and to the RCA pin jacks will be mono mixed at a ﬁxed balance. If you want to

change the balance, adjust the volume of the connected sound source.

Musical instrument

Microphone

Background music source

System with two DBRs and subwoofers

This system is the most suitable for a main speaker system. If desired, you can add another DBR to create

a ﬂoor monitor system.

Main application: small-sized live venue, house of worship, event site

Note

We recommend to use Yamaha DXS series (referred to in this manual as DXS) as a subwoofer. In this case,

we recommend that the DBR’s HPF cutoff frequency and the DXS’s LPF cutoff frequency are set to the same

settings; however, you can adjust it as desired.

R L

Subwoofer Mixer Subwoofer

Input jacks (CH1 and CH2)

These are balanced combo jacks that support both XLR and phone plugs (both CH1 and CH2), and RCA-

pin plugs (CH2 only). For the combo jacks, connect a mixer, microphone, or digital musical instrument

such as a keyboard. For RCA-pin jacks, connect a device such as an MP3 player or a CD player. For

devices with high level signals such as a mixer, connect to CH2, or connect to CH1 then set the [MIC/

LINE] switch (

) to [LINE].

XLR Phone RCA-pin

[LEVEL] knobs

Adjust the level of each input jack (

[MIC/LINE] switch

Set this switch to [MIC] or [LINE] for the CH1 jack, depending on the level of the input signal. For low-

level signals (such as microphones), set the switch to [MIC]. For high-level signals (such as mixer), set the

switch to [LINE].

Output switch

Selects the output signal sent to the output jack (

[CH1 THRU]: Delivers the direct output signal of CH1 only. Signal from CH2 will not be output.

[CH1+2 MIX]: Outputs the mixed signals of CH1 and CH2.

Output jack

This is a balanced XLR jack. This can be used to connect another DBR speaker. Outputs the signal

selected by

output switch.

[LIMIT] indicator

Indicates (lit in red) that the limiter is on when the output voltage of the ampliﬁer has exceeded the

maximum level, or when excessive integral power consumption is detected. If this indicator stays lit, lower

the input level.

Note Integral power consumption refers to the sum of power provided to the speaker driver per unit time.

[SIGNAL] indicator

Indicates (lit in green) when an audio signal exceeding the threshold has been detected.

[PROTECTION] indicator

Indicates (lit in red) when the protection circuit is active. The protection circuit will be activated and the

speaker outputs will be muted in the situations listed below.

• If ampliﬁer overheating is detected

• If overcurrent is detected

• When turning the power on; the protection circuit will be activated for a few seconds to prevent noise.

The indicator turns off when the power supply has started normally.

If the protection circuit has engaged, waiting until the ampliﬁer cools down or powering off and on again

will return to normal operation. If the unit does not return to normal operation, please contact your Yamaha

dealer.

[POWER] indicator

Indicates (lit in green) when the [ / ] (power) (

) switch is turned on.

[D-CONTOUR] indicator

Indicates (lit in yellow) when the [D-CONTOUR] switch (

) is set to [FOH/MAIN] or [MONITOR].

[D-CONTOUR] switch

Selects one of the D-CONTOUR (Dynamic CONTOUR) presets.

[FOH/MAIN]: Boosts the high and low frequency components so that the frequency response is suitable

for a main speaker.

[MONITOR]: Reduces the low frequency range, which could otherwise tend to be boomy if the speaker is

set directly on the ﬂoor. This enables you to hear mid and high frequency ranges clearly when using as a

ﬂoor monitor.

[OFF]: Turns off D-CONTOUR. This is a generic frequency response setting.

[HPF] switch

Selects the cutoff frequency of the high pass ﬁlter. If you set this switch to [120Hz] or [100Hz], the low

frequency components below each threshold will be cut. If you use the unit alone, set this switch to [OFF].

If you plan to use the unit along with a subwoofer, we recommend that you set this switch to [120Hz] or

[100Hz].

Vent

The unit contains a cooling fan. Since the air for cooling is taken in and expelled here, be careful not to

block this vent.

[AC IN] socket

Connect the supplied power cord here. First connect the power cord to the unit, then plug it into an

appropriate AC power outlet.

CAUTION

Turn off the power before you connect or disconnect the power cord.

[ / ] (power) switch

Turns power to the unit on [

] or off [ ]. First, turn on the power of the connected sound source (external

device), then the unit. When turning off the power, reverse the order by turning off the power of the unit ﬁrst

and then the connected sound source (external device).

CAUTION

Even when the switch is in the off position, a small amount of electricity is still ﬂowing to the unit. If it will not be used for an

extended period of time, therefore, be sure to unplug the power cord from the wall AC outlet.

Note • Rapidly turning the unit on and off in succession can cause it to malfunction. After turning the unit off, wait for

about 5 seconds before turning it on again.

• If you are using multiple units, turn on the power to each unit one by one. If you turn on the power to multiple

units simultaneously, a temporary drop in the power voltage may occur, possibly resulting in abnormal operation

of the units.

Screw holes (M8)

Use these M8 size screw holes for installing separately sold brackets or commercially available eye bolts.

Pole socket

This socket adapts to commercially available speaker stands and speaker poles of 35 mm diameter.

Controls and Connectors

Setup Examples

Rear

Bottom

Troubleshooting

Symptom Possible causes Possible solution

Power does not turn on. The power cord is not connected properly. Connect the power cord all the way in so that it is ﬁrmly in place.

Power suddenly went off. The protection system has been activated, shutting

down the power supply.

Turn off the power, wait until the ampliﬁer cools down, and then turn on again.

No Sound. The cable is not connected properly. Connect the cable all the way in so that it is ﬁrmly in place.

Sound is interrupted suddenly. The protection circuit has been activated, muting the

output.

Wait until the ampliﬁer cools down. If the unit won’t automatically reset itself, turn off the power, and then on

again.

Sound howls (feedback). A microphone is directed toward the speaker. Aim the speaker away from the area where the microphone picks up sound.

Sound is ampliﬁed too much. Lower the volume of input device and locate the microphone more closely to the sound source.

Each speaker sound differs (if multiple speakers are

used).

Settings for each speaker differ. Set the [HPF] switch and [D-CONTOUR] switch of each speaker to the same positions.

Sound is

distorted.

The [LIMIT] indicator is off. Input volume is excessive. When the [MIC/LINE] switch is set to [MIC], and even if you lower the volume fully the sound is still distorted,

set the switch to the [LINE] position. If the sound is still distorted even if the switch has been set to [LINE],

lower the volume of the connected input devices.

The [LIMIT] indicator is on. Output volume is excessive. Turn the [LEVEL] knob to lower the output level to a point so that the [LIMIT] indicator lights only occasionally.

The microphone volume is too low. The [MIC/LINE] switch is set to [LINE]. Set the [MIC/LINE] switch to the [MIC] position.

Low and high frequency are unbalanced. The output limiter is active. Lower the input level or the output level until the [LIMIT] indicator lights occasionally.

If any speciﬁc problem should persist, however, please contact your Yamaha dealer.

Installation Examples

Installation using separately sold Yamaha speaker

brackets

Attach the bracket to two screw holes at the bottom of the unit using commercially available screws

(M8 x 16 mm) or eye bolts (M8 x 15 mm). For details on installing the bracket, refer to the corresponding

manual.



Using the BWS251-300 or BWS251-400 wall mounting

bracket

Maximum tilt

angle

The tilt angle depends on the position relation between the speaker

and the wall. The maximum downward tilt angle is shown in the

following chart.

Maximum tilt angle BWS251-300 BWS251-400

DBR15 8° 17.5°

DBR12 11° 23°

DBR10 20° 35°



Using the BCS251 ceiling bracket

235923

Max. 45°

(Pullback point for DBR15

and DBR12 only)



Using the BBS251 baton bracket

235923

Max. 45°

Baton diameter

34 -

Note

In order to prevent the unit from falling down, attach the safety wire as

shown in the illustration.

CAUTION

• Before doing any installation or construction work, consult with your Yamaha dealer.

• For optimum safety, the installation should be checked thoroughly at regular intervals. Some fittings may deteriorate

over extended periods of time due to wear and/or corrosion.

• When choosing the installation location, suspension wire and mounting hardware, make sure all are strong enough to

support the weight of the speaker.

• Make sure to take measures to prevent the speaker from falling down in the event of a installation failure.

• When installing the safety wire to the wall, install it higher than the wire’s attachment point on the speaker, with as little

slack as possible. If the wire is too long, and the speaker happens to fall, the wire may snap as a result of too much

strain.

Yamaha cannot be held responsible for damage or injury caused by insufﬁcient strength of the support

structure or improper installation.

Installation using eye bolts

Attach commercially-available eye bolts (M8 x 15 mm) to the screw holes located at the bottom (two locations)

and on the upper rear (one location, only for DBR15 and DBR12). Keep in mind that you will need two points

at the bottom to suspend the unit.

Note

Make sure to use eye bolts according to the standards and safety regulations in your area.

M8 eye bolt

Max. 45°

(Pullback point for

DBR15 and DBR12 only)



NOTICE

The strength of an eye bolt differs depending on the suspension angle. Make sure to use eye bolts within a

range of 0 to 45 degrees from a right angle (as shown).

Correct: Within 45° from a right angle

0°

45°

Max. 45°

Incorrect: Do not suspend the eye bolts as shown in the illustrations below.

Only one suspension point

More than 45° from a right angle

More than 45° More than 45°

PRECAUTIONS

General Specifications

General Specications DBR15 DBR12 DBR10

System Type 2-way, Bi-amp Powered Speaker, Bass-reﬂex Type

Frequency Range (-10dB) 49 Hz–20 kHz 52 Hz–20 kHz 55 Hz–20 kHz

Coverage Angle (Horizontal x Vertical) H90

x V60

Constant Directivity Horn

Measured Maximum SPL (Peak) IEC Noise@1m 132 dB SPL 131 dB SPL 129 dB SPL

Crossover 2.1 kHz 2.1 kHz 2.1 kHz

Power Amplier

Power Rating

Dynamic 1000 W (LF: 800 W, HF: 200 W) 700 W (LF: 500 W, HF: 200 W)

Continuous 465 W (LF: 400 W, HF: 65 W) 325 W (LF: 260 W, HF: 65 W)

Power Consumption 74 W 60 W

Components

LF 15" Cone, 2.5" Voice Coil 12" Cone, 2" Voice Coil 10" Cone, 2" Voice Coil

HF 1.4" Voice Coil, Compression Driver 1" Voice Coil, Compression Driver

Dimensions (WxHxD, Including Rubber Feet) 455 x 700 x 378 mm (17.9" x 27.6" x 14.9") 376 x 601 x 348 mm (14.8" x 23.7" x 13.7") 308 x 493 x 289 mm (12.1" x 19.4" x 11.4")

Net Weight 19.3 kg (42.6 lbs) 15.8 kg (34.8 lbs) 10.5 kg (23.2 lbs)

Handles Side x 2 Top x 1

Pole Socket

35 mm Bottom x 1

Rigging Points Bottom x 2, Rear x 1 (Fit for M8 x 15 mm) Bottom x 2 (Fit for M8 x 15 mm)

Optional Speaker Brackets BBS251, BCS251, BWS251-300, BWS251-400

I/O Connectors

Input INPUT1: Combo x1, INPUT2: Combo x 1 + RCA-pin x 2

Output XLR3-32 x 1 (CH1 Paralell Through or CH1+CH2 Mix)

Input Sensitivity (Level: Center) INPUT1: LINE: +10 dBu, MIC: -22 dBu, INPUT2: +10 dBu

Maximum Input Level INPUT1: LINE: +24 dBu, MIC: -8 dBu, INPUT2: +24 dBu

0 dBu is referenced to 0.775 Vrm

Speciﬁcations and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or speciﬁcations at any time without prior notice. Since speciﬁcations,

equipment or options may not be the same in every locale, please check with your Yamaha dealer.

Pullback point (only for DBR15 and DBR12)

• When the unit is shipped from the factory, a seal is stuck

on the pullback point (screw hole). Make sure to peel off

the seal when using the pullback point.

• The DBR10 does not have a pullback point.

Pullback point

(M8 screw hole)

Upper rear of the unit

Securing the screws and eye

bolts

• Insert the screw or eye bolt through the

washer to attach them.

Apply thread-locking

uid to the eye bolt

PLEASE READ CAREFULLY BEFORE

PROCEEDING

Please keep this manual in a safe place for future

reference.

WARNING

Always follow the basic precautions listed below to

avoid the possibility of serious injury or even death from

electrical shock, short-circuiting, damages, re or other

hazards. These precautions include, but are not limited

to, the following:

Power supply/power cord

• Do not place the power cord near heat sources such

as heaters or radiators, and do not excessively bend or

otherwise damage the cord, place heavy objects on it,

or place it in a position where anyone could walk on, trip

over, or roll anything over it.

• Only use the voltage speciﬁed as correct for the device.

The required voltage is printed on the name plate of the

device.

• Use only the supplied power cord/plug.

• Check the electric plug periodically and remove any dirt

or dust which may have accumulated on it.

• Be sure to connect to an appropriate outlet with a

protective grounding connection. Improper grounding

can result in electrical shock, damage to the device(s), or

even ﬁre.

Do not open

• This device contains no user-serviceable parts. Do not

open the device or attempt to disassemble the internal

parts or modify them in any way. If it should appear to be

malfunctioning, discontinue use immediately and have it

inspected by qualiﬁed Yamaha service personnel.

Water warning

• Do not expose the device to rain, use it near water or in

damp or wet conditions, or place on it any containers

(such as vases, bottles or glasses) containing liquids

which might spill into any openings. If any liquid such

as water seeps into the device, turn off the power

immediately and unplug the power cord from the AC

outlet. Then have the device inspected by qualiﬁed

Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

Fire warning

• Do not put burning items, such as candles, on the unit.

A burning item may fall over and cause a ﬁre.

If you notice any abnormality

• When one of the following problems occur, immediately

turn off the power switch and disconnect the electric

plug from the outlet. Then have the device inspected by

Yamaha service personnel.

– The power cord or plug becomes frayed or damaged.

– It emits unusual smells or smoke.

– Some object has been dropped into the device.

– There is a sudden loss of sound during use of the

device.

• If this device should be dropped or damaged,

immediately turn off the power switch, disconnect

the electric plug from the outlet, and have the device

inspected by qualiﬁed Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to

avoid the possibility of physical injury to you or others,

or damage to the device or other property. These

precautions include, but are not limited to, the following:

Power supply/power cord

• When removing the electric plug from the device or an

outlet, always hold the plug itself and not the cord. Pulling

by the cord can damage it.

• Remove the electric plug from the outlet when the device

is not to be used for extended periods of time, or during

electrical storms.

Location

• Do not place the device in an unstable position where it

might accidentally fall over.

• Do not block the vents. This device has ventilation holes at

the rear to prevent the internal temperature from becoming

too high. In particular, do not place the device on its

side or upside down. Inadequate ventilation can result in

overheating, possibly causing damage to the device(s),

or even ﬁre.

• When installing the device:

– Do not cover it with any cloth.

– Do not install it on a carpet or rug.

– Do not use the device in a conﬁned, poorly-ventilated

location.

Inadequate ventilation can result in overheating, possibly

causing damage to the device(s), or even ﬁre. Make sure

that there is adequate space around the device: at least

30cm above, 30cm at the sides and 30cm behind.

• Do not use the speaker’s handles for suspended

installation. Doing so can result in damage or injury.

• Do not hold the bottom of the device when transporting or

moving it. In doing so, you may pinch your hands under

the device, and result in injury.

• Do not press the rear panel of the device against the wall.

Doing so may cause the plug to come in contact with the

wall and detach from the power cord, resulting in short

circuiting, malfunction, or even ﬁre.

• Do not place the device in a location where it may come

into contact with corrosive gases or salt air. Doing so may

result in malfunction.

• Before moving the device, remove all connected cables.

• When setting up the device, make sure that the AC outlet

you are using is easily accessible. If some trouble or

malfunction occurs, immediately turn off the power switch

and disconnect the plug from the outlet. Even when the

power switch is turned off, electricity is still ﬂowing to the

product at the minimum level. When you are not using the

product for a long time, make sure to unplug the power

cord from the wall AC outlet.

• Always consult qualiﬁed Yamaha service personnel if the

device installation requires construction work, and make

sure to observe the following precautions.

– Choose mounting hardware and an installation location

that can support the weight of the device.

– Avoid locations that are exposed to constant vibration.

– Use the required tools to install the device.

– Inspect the device periodically.

Connections

• Before connecting the device to other devices, turn off the

power for all devices. Before turning the power on or off

for all devices, set all volume levels to minimum.

Maintenance

• Remove the power plug from the AC outlet when cleaning

the device.

Handling caution

• Do not insert your ﬁngers or hands in any gaps or

openings on the device (vents, etc.).

• Avoid inserting or dropping foreign objects (paper,

plastic, metal, etc.) into any gaps or openings on the

device (vents, etc.) If this happens, turn off the power

immediately and unplug the power cord from the AC

outlet. Then have the device inspected by qualiﬁed

Yamaha service personnel.

• Do not rest your weight on the device or place heavy

objects on it, and avoid use excessive force on the

buttons, switches or connectors.

• Do not use the device for a long period of time at a high

or uncomfortable volume level, since this can cause

permanent hearing loss. If you experience any hearing

loss or ringing in the ears, consult a physician.

• Do not operate the device if the sound is distorting.

Prolonged use in this condition could cause overheating

and result in ﬁre.

• Do not pull the cables connected to the microphones, etc.

Yamaha cannot be held responsible for damage caused

by improper use or modiﬁcations to the device, or data

that is lost or destroyed.

(PA-3)

NOTICE

To avoid the possibility of malfunction/ damage to the

product, damage to data, or damage to other property,

follow the notices below.

Handling and maintenance

• Do not expose the device to excessive dust or vibration,

or extreme cold or heat (such as in direct sunlight, near a

heater, or in a car during the day), in order to prevent the

possibility of panel disﬁguration, unstable operation, or

damage to the internal components.

• Do not place vinyl, plastic or rubber objects on the device,

since this might discolor the panel.

• When cleaning the device, use a dry and soft cloth. Do not

use paint thinners, solvents, cleaning ﬂuids, or chemical-

impregnated wiping cloths.

• Condensation can occur in the device due to rapid,

drastic changes in ambient temperature—when the device

is moved from one location to another, or air conditioning

is turned on or off, for example. Using the device while

condensation is present can cause damage. If there is

reason to believe that condensation might have occurred,

leave the device for several hours without turning on the

power until the condensation has completely dried out.

• When turning on the AC power in your audio system,

always turn on the device LAST, to avoid speaker

damage. When turning the power off, the device should

be turned off FIRST for the same reason.

• Interference From Cell Phones

Using a cell phone near the speaker system can induce

noise. If this occurs, move the cell phone further away

from the speaker system.

• Air blowing out of the bass reﬂex ports is normal, and

often occurs when the speaker is handling program

material with heavy bass content.

• Always turn the power off when the device is not in use.

Connectors

• XLR-type connectors are wired as follows (IEC60268

standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-).

Information for Users on Collection and Disposal of Old Equipment

This symbol on the products, packaging, and/or accompanying documents means that used electrical

and electronic products should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to applicable collection

points, in accordance with your national legislation and the Directives 2002/96/EC.

By disposing of these products correctly, you will help to save valuable resources and prevent any

potential negative effects on human health and the environment which could otherwise arise from

inappropriate waste handling.

For more information about collection and recycling of old products, please contact your local

municipality, your waste disposal service or the point of sale where you purchased the items.

[For business users in the European Union]

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for

further information.

[Information on Disposal in other Countries outside the European Union]

This symbol is only valid in the European Union. If you wish to discard these items, please contact your

local authorities or dealer and ask for the correct method of disposal.

(weee_eu_en_01)

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modiﬁcations not expressly approved

by Yamaha may void your authority, granted by the

FCC, to use the product.

2. IMPORTANT: When connecting this product to

accessories and/or another product use only high

quality shielded cables. Cable/s supplied with

this product MUST be used. Follow all installation

instructions. Failure to follow instructions could void

your FCC authorization to use this product in the

USA.

3. NOTE: This product has been tested and found

to comply with the requirements listed in FCC

Regulations, Part 15 for Class “B” digital devices.

Compliance with these requirements provides a

reasonable level of assurance that your use of

this product in a residential environment will not

result in harmful interference with other electronic

devices. This equipment generates/uses radio

frequencies and, if not installed and used according

to the instructions found in the users manual, may

cause interference harmful to the operation of

other electronic devices. Compliance with FCC

regulations does not guarantee that interference

will not occur in all installations. If this product is

found to be the source of interference, which can

be determined by turning the unit “OFF” and “ON”,

please try to eliminate the problem by using one of

the following measures:

Relocate either this product or the device that is

being affected by the interference.

Utilize power outlets that are on different branch

(circuit breaker or fuse) circuits or install AC line

ﬁlter/s.

In the case of radio or TV interference, relocate/

reorient the antenna. If the antenna lead-in is 300

ohm ribbon lead, change the lead-in to co-axial type

cable.

If these corrective measures do not produce

satisfactory results, please contact the local retailer

authorized to distribute this type of product. If

you can not locate the appropriate retailer, please

contact Yamaha Corporation of America, Electronic

Service Division, 6600 Orangethorpe Ave, Buena

Park, CA90620

The above statements apply ONLY to those

products distributed by Yamaha Corporation of

America or its subsidiaries.

* This applies only to products distributed by YAMAHA

CORPORATION OF AMERICA.

(class B)

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

WARNING: THIS APPARATUS MUST BE EARTHED

IMPORTANT. The wires in this mains lead are coloured

in accordance with the following code:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug

proceed as follows:

The wire which is coloured GREEN-and-YELLOW

must be connected to the terminal in the plug which is

marked by the letter E or by the safety earth symbol

or colored GREEN or GREEN-and-YELLOW.

The wire which is coloured BLUE must be connected

to the terminal which is marked with the letter N or

coloured BLACK.

The wire which is coloured BROWN must be

connected to the terminal which is marked with the

letter L or coloured RED.

(3 wires)

In Finland: Laite on liitettävä suojamaadoituskoskettimilla

varustettuun pistorasiaan.

In Norway: Apparatet må tilkoples jordet stikkontakt.

In Sweden: Apparaten skall anslutas till jordat uttag.

(class I hokuo)

이 기기는 가정용(B급) 전자파적합기기로서 주로 가정에서

사용하는 것을 목적으로 하며, 모든 지역에서 사용할 수

있습니다.

(class b korea)

HEAD OFFICE

Yamaha Corporation, Audio Products Sales and Marketing Division

Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650

CANADA

Yamaha Canada Music Ltd.

135 Milner Avenue, Toronto, Ontario,

M1S 3R1, Canada

Tel: 416-298-1311

U.S.A.

Yamaha Corporation of America

6600 Orangethorpe Avenue, Buena Park, CA 90620,

U.S.A.

Tel: 714-522-9011

MEXICO

Yamaha de México, S.A. de C.V.

Av. Insurgentes Sur 1647 Piso 9, Col. San José

Insurgentes, Delegación Benito Juárez, México,

D.F., C.P. 03900

Tel: 55-5804-0600

BRAZIL

Yamaha Musical do Brasil Ltda.

Rua Joaquim Floriano, 913 - 4º andar, Itaim Bibi,

EP 04534-013 São Paulo, SP. BRAZIL

Tel: 011-3704-1377

ARGENTINA

Yamaha Music Latin America, S.A.,

Sucursal Argentina

Olga Cossettini 1553, Piso 4 Norte,

Madero Este-C1107CEK

Buenos Aires, Argentina

Tel: 011-4119-7000

VENEZUELA

Yamaha Music Latin America, S.A.,

Sucursal Venezuela

C.C. Manzanares Plaza P4

Ofic. 0401- Manzanares-Baruta

Caracas Venezuela

Tel: 58-212-943-1877

PANAMA AND OTHER LATIN

AMERICAN COUNTRIES/

CARIBBEAN COUNTRIES

Yamaha Music Latin America, S.A.

Torre Banco General, Piso No.7, Marbella,

Calle 47 y Aquilino de la Guardia,

Ciudad de Panamá, República de Panamá

Tel: +507-269-5311

THE UNITED KINGDOM/IRELAND

Yamaha Music Europe GmbH (UK)

Sherbourne Drive, Tilbrook, Milton Keynes,

MK7 8BL, U.K.

Tel: 01908-366700

GERMANY

Yamaha Music Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: 04101-3030

SWITZERLAND/LIECHTENSTEIN

Yamaha Music Europe GmbH

Branch Switzerland in Zürich

Seefeldstrasse 94, 8008 Zürich, Switzerland

el: 044-387-8080

AUSTRIA/BULGARIA

Yamaha Music Europe GmbH Branch Austria

Schleiergasse 20, A-1100 Wien, Austria

Tel: 01-60203900

CZECH REPUBLIC/HUNGARY/

ROMANIA/SLOVAKIA/SLOVENIA

Yamaha Music Europe GmbH

Branch Austria (Central Eastern Europe Office)

Schleiergasse 20, A-1100 Wien, Austria

Tel: 01-60203900

POLAND/LITHUANIA/LATVIA/ESTONIA

Yamaha Music Europe GmbH

Branch Poland Office

ul. Wrotkowa 14 02-553 Warsaw, Poland

Tel: 022-500-2925

MALTA

Olimpus Music Ltd.

The Emporium, Level 3, St. Louis Street Msida

MSD06

Tel: 02133-2144

NETHERLANDS/BELGIUM/

LUXEMBOURG

Yamaha Music Europe Branch Benelux

Clarissenhof 5-b, 4133 AB Vianen, Netherlands

Tel: 0347-358 040

FRANCE

Yamaha Music Europe

7 rue Ambroise Croizat, Zone d'activites Pariest,

77183 Croissy-Beaubourg, France

Tel: 01-64-61-4000

ITALY

Yamaha Music Europe GmbH, Branch Italy

Viale Italia 88, 20020 Lainate (Milano), Italy

Tel: 02-935-771

SPAIN/PORTUGAL

Yamaha Music Europe GmbH Ibérica, Sucursal

en España

Ctra. de la Coruna km. 17,200, 28231

Las Rozas (Madrid), Spain

Tel: +34-91-639-88-88

GREECE

Philippos Nakas S.A. The Music House

147 Skiathou Street, 112-55 Athens, Greece

Tel: 01-228 2160

SWEDEN/FINLAND/ICELAND

Yamaha Music Europe GmbH Germany filial

Scandinavia

J. A. Wettergrensgata 1, Box 30053

S-400 43 Göteborg, Sweden

Tel: +46 31 89 34 00

DENMARK

Yamaha Music Europe GmbH, Tyskland – filial

Denmark

eneratorvej 6A, DK-2730 Herlev, Denmark

Tel: 44 92 49 00

NORWAY

Yamaha Music Europe GmbH Germany -

Norwegian Branch

Grini Næringspark 1, N-1361 Østerås, Norway

Tel: 67 16 78 00

RUSSIA

Yamaha Music (Russia) LLC.

Room 37, bld. 7, Kievskaya street, Moscow,

121059, Russia

Tel: 495 626 5005

OTHER EUROPEAN COUNTRIES

Yamaha Music Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: +49-4101-3030

Yamaha Music Gulf FZE

Office JAFZA 16-512, P.O.Box 17328,

Jebel Ali - Dubai, UAE

el: +971-4-881-5868

TURKEY

Yamaha Music Europe GmbH

Merkezi Almanya Türkiye İstanbul Şubesi

Maslak Meydan Sokak No:5 Spring Giz Plaza

Bağ?ms?z Böl. No:3, 34398 Şişli İstanbul

Tel: +90-212-999-8010

CYPRUS

Yamaha Music Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: 04101-3030

OTHER COUNTRIES

Yamaha Music Gulf FZE

Office JAFZA 16-512, P.O.Box 17328,

Jebel Ali - Dubai, U.A.E

Tel: +971-4-881-5868

THE PEOPLE’S REPUBLIC OF CHINA

Yamaha Music & Electronics (China) Co.,Ltd.

2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,

Shanghai, China

Tel: 021-6247-2211

INDIA

Yamaha Music India Pvt. Ltd.

Spazedge building, Ground Floor, Tower A, Sector

47, Gurgaon- Sohna Road, Gurgaon, Haryana, India

Tel: 0124-485-3300

INDONESIA

PT. Yamaha Musik Indonesia (Distributor)

Yamaha Music Center Bldg. Jalan Jend. Gatot

Subroto Kav. 4, Jakarta 12930, Indonesia

Tel: 021-520-2577

KOREA

Yamaha Music Korea Ltd.

8F, 9F, Dongsung Bldg. 158-9 Samsung

-Dong,

Kangnam-Gu, Seoul, Korea

Tel: 02-3467-3300

MALAYSIA

Yamaha Music (Malaysia) Sdn., Bhd.

No.8, Jalan Perbandaran, Kelana Jaya, 47301

Petaling Jaya, Selangor, Malaysia

Tel: 03-78030900

SINGAPORE

Yamaha Music (Asia) Private Limited

Block 202 Hougang Street 21, #02-00,

Singapore 530202, Singapore

Tel: 65-6747-4374

TAIWAN

Yamaha Music & Electronics Taiwan Co.,Ltd.

3F, No.6, Section 2 Nan-Jing East Road, Taipei,

Taiwan R.O.C.

Tel: 02-2511-8688

THAILAND

Siam Music Yamaha Co., Ltd.

3, 4, 15 and 16th floor, Siam Motors Building,

891/1 Rama 1 Road, Wangmai,

Pathumwan, Bangkok 10330, Thailand

Tel: 02-215-2622

VIETNAM

Yamaha Music Vietna m Company Limited

15th Floor, Nam A Bank Tower, 201-203 Cach

Mang Thang Tam St., Ward 4, Dist.3,

Ho Chi Minh City, Vietnam

Tel: +84-8-3818-1122

OTHER ASIAN COUNTRIES

Yamaha Corporation

Sales & Marketing Division

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2312

AUSTRALIA

Yamaha Music Australia Pty. Ltd.

Level 1, 99 Queensbridge Street, Southbank,

Victoria 3006, Australia

Tel: 3-9693-5111

COUNTRIES AND TRUST

TERRITORIES IN PACIFIC OCEAN

Yamaha Corporation

Sales & Marketing Division

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2312

NORTH AMERICA

CENTRAL & SOUTH AMERICA

EUROPE

AFRICA

MIDDLE EAST

ASIA

OCEANIA

PA36

For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below.

Yamaha Pro Audio global web site

http://www.yamahaproaudio.com/

Yamaha Manual Library

http://www.yamaha.co.jp/manual/

C.S.G., PA Development Division

Published 07/2014 KSZC*.*-01A0

Printed in Indonesia

Yamaha DBR15/DBR12/DBR10 Manuel utilisateur

Marque: Yamaha

Modèle: DBR15/DBR12/DBR10

Catégorie: Amplificateurs audio

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

italiano: Yamaha DBR15/DBR12/DBR10 Manuale utente
English: Yamaha DBR15/DBR12/DBR10 User manual
español: Yamaha DBR15/DBR12/DBR10 Manual de usuario
Deutsch: Yamaha DBR15/DBR12/DBR10 Benutzerhandbuch
русский: Yamaha DBR15/DBR12/DBR10 Руководство пользователя
Nederlands: Yamaha DBR15/DBR12/DBR10 Handleiding
português: Yamaha DBR15/DBR12/DBR10 Manual do usuário
dansk: Yamaha DBR15/DBR12/DBR10 Brugermanual
polski: Yamaha DBR15/DBR12/DBR10 Instrukcja obsługi
čeština: Yamaha DBR15/DBR12/DBR10 Uživatelský manuál
svenska: Yamaha DBR15/DBR12/DBR10 Användarmanual
Türkçe: Yamaha DBR15/DBR12/DBR10 Kullanım kılavuzu
suomi: Yamaha DBR15/DBR12/DBR10 Ohjekirja
română: Yamaha DBR15/DBR12/DBR10 Manual de utilizare

Yamaha DBR15/DBR12/DBR10 Manuel utilisateur

Yamaha DBR15/DBR12/DBR10 Manuel utilisateur

dans d''autres langues

Documents connexes