Dell PowerVault DP600 Manuel utilisateur

Dell™ PowerVault™

600 Systems

Getting Started

With Your System

Guide de mise en route

Primeiros passos com o sistema

Procedimientos iniciales con el sistema

Model MVT01

Dell™ PowerVault™ 600

Systems

Getting Started

With Your System

Model MVT01

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of

your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data

and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury,

or death.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly

forbidden.

Trademarks used in this text: Dell, the DELL logo, and PowerVault, are trademarks of Dell Inc.;

Intel Core and Core 2 Duo are trademarks and Intel, Pentium and Xeon are registered trademarks of

Intel Corporation in the U.S. and other countries; Microsoft, Windows, and Windows Storage Server

are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or

other countries.

Other trademarks and trade names may be used in this document to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and

trade names other than its own.

Model MVT01

September 2007 P/N CX193 Rev. A00

Contents 3

Contents

System Features . . . . . . . . . . . . . . . . . . . . . . 5

Supported Operating Systems

. . . . . . . . . . . . . . . 7

Other Information You May Need

. . . . . . . . . . . . . 7

Obtaining Technical Assistance

. . . . . . . . . . . . . 7

Installation and Configuration

. . . . . . . . . . . . . . . 8

Unpacking the System

. . . . . . . . . . . . . . . . 8

Installing the Rails and System in a Rack

. . . . . . 9

Connecting the Keyboard, Mouse, and Monitor

. . 10

Connecting the Power

. . . . . . . . . . . . . . . 10

Installing the Power Cord Retention Bracket

. . . 11

Turning on the System

. . . . . . . . . . . . . . . 11

Installing the Bezel

. . . . . . . . . . . . . . . . . 12

Complete the 0perating System Setup

. . . . . . . . . . 12

Technical Specifications

. . . . . . . . . . . . . . . . 12

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4 Contents

Getting Started With Your System 5

System Features

The major hardware and software features of your system include:

• One or two Dual-Core Intel

®

Xeon

®

Processors 5000 Sequence.

• Support for symmetric multiprocessing (SMP), which is available on systems

with two Intel Xeon processors. SMP greatly improves overall system

performance by dividing processor operations between independent

processors. To take advantage of this feature, you must use an operating

system that supports multiprocessing.

NOTE: If you decide to upgrade your system by installing a second processor,

you must order the processor upgrade kits from your supplier. Not all versions

of the Intel Xeon processor will work properly as additional processors. The

upgrade kit contains the correct version of the processor, heat sink, and fan

as well as the instructions for performing the upgrade.

• A minimum of 512 MB of 533 or 667 MHz (when available), Fully

Buffered DIMMs (FBD), upgradable to a maximum of 48 GB by installing

combinations of 256-MB, 512-MB, 1-GB, 2-GB, or 4-GB memory modules

in the twelve memory module sockets on the system board.

The system also features redundant memory, which provides memory

sparing or memory mirroring. Either feature is available if eight or twelve

identical memory modules are installed.

• Support for up to ten 3.5-inch, internal hot-pluggable Serial-Attached

SCSI (SAS) or SATA hard drives (eight 3.5-inch internal hard drives

with hot-pluggable backplane board, and support for two additional

hot-pluggable 3.5-inch drives in the peripheral bay using the optional

1x2 flexbay backplane board).

• Peripheral bay provides support for an optional optical drive and an

optional half-height tape backup unit (TBU). A full-height TBU is

supported with the 1x2 flexbay bracket removed.

• An optional single, 1.44-MB, 3.5-inch diskette drive.

• An optional CD, DVD, or combination CD-RW/DVD drive.

NOTE: DVD devices are data only.

• An intrusion switch that signals the appropriate systems management

software if the top cover is opened.

• Up to two hot-pluggable, 930-W power supplies in a 1 + 1 redundant

configuration.

• Six hot-pluggable system cooling fans.

6 Getting Started With Your System

The system board includes the following features:

• Six PCI slots located in an expansion-card cage. Slots 1 and 2 are 3.3-V,

64-bit, 133-MHz PCI-X slots; slot 3 is a 3.3-V, PCIe x8 lane; slots 4 through 6

are 3.3-V, PCIe x4 lanes. Expansion-card slots accommodate full-height,

full-length expansion cards. PCIe slots accommodate up to x8 expansion

cards.

• Dedicated PCI slot for an integrated SAS host bus adapter or an optional

integrated RAID controller card with 256 MB of cache memory and a

RAID battery.

NOTE: System boot is not supported from an external device attached to a

SAS or SCSI adapter, including SAS 5/E, PERC 5/E, or PERC 4e/DC. Contact

your technical support provider for the latest support information about

booting from external devices.

• Two integrated Gigabit Ethernet NICs, capable of supporting 10-Mbps,

100-Mbps, and 1000-Mbps data rates.

• Six USB 2.0-compliant connectors (two on the front and four on the back)

capable of supporting a diskette drive, a CD-ROM or DVD-ROM drive,

a keyboard, a mouse, or a USB flash drive.

• Optional remote access controller (RAC) for remote systems management.

• An integrated VGA-compatible video subsystem with an ATI ES1000,

33-MHz PCI video controller. This video subsystem contains 16 MB of

DDR SDRAM video memory (nonupgradable). Maximum resolution is

1600 x 1200 with 64 K colors; true-color graphics are supported in the

following resolutions: 640 x 480, 800 x 600, 1024 x 768, 1152 x 864, and

1280 x 1024. When the optional RAC is installed, the video resolution

is 1024 X 768.

• Systems management circuitry that monitors operation of the system fans

as well as critical system voltages and temperatures. The systems

management circuitry works in conjunction with the systems management

software.

• Standard baseboard management controller with serial access.

• Back-panel connectors include one serial, one video, four USB, and

two NIC connectors.

Getting Started With Your System 7

• Front-panel connectors include a video and two USB connectors.

• Front-panel 1x5 LCD for system ID and error messaging.

• System ID button on the front and back panels.

For more information about specific features, see "Technical Specifications"

on page 12.

Supported Operating Systems

• Microsoft

®

Windows Storage Server™ 2003 R2 Express Edition (x64)

• Microsoft

Windows Storage Server 2003 R2 Workgroup Edition (x64)

Other Information You May Need

CAUTION: The Product Information Guide provides important safety and

regulatory information. Warranty information may be included within this

document or as a separate document.

• The

Rack Installation Instructions

or

Rack Installation Guide

included

with your rack solution describes how to install your system into a rack.

• The

Hardware Owner’s Manual

provides information about system

features and describes how to troubleshoot the system and install or

replace system components. The

Hardware Owner’s Manual

is available

on the CDs that came with your system or from your technical provider.

• CDs included with your system provide documentation and tools for

configuring and managing your system.

• Release notes or readme files may be included to provide last-minute

updates to the system or documentation or advanced technical reference

material intended for experienced users or technicians.

Obtaining Technical Assistance

If you do not understand a procedure in this guide or if the system

does not perform as expected, see your Hardware Owner’s Manual.

8 Getting Started With Your System

Installation and Configuration

CAUTION: Before performing the following procedure, read and follow the

safety instructions and important regulatory information in your Product

Information Guide.

This section describes the steps to set up your system for the first time.

The illustrations that follow show a rack-mounted system, but the installation

procedure applies in large part to a stand-alone tower system. In place of the

rack installation in step 2, refer to the documentation included with your

system on installing the stabilizer feet on your system.

CAUTION: Installing the feet on a stand-alone tower system is necessary to

provide a stable foundation for the system. Failure to install the feet poses the

risk of having the system tip over, possibly causing bodily injury or damage to

the system.

CAUTION: Whenever you need to lift the system, get others to assist you. To avoid

injury, do not attempt to lift the system by yourself.

Unpacking the System

Unpack your system and identify each item.

Keep all shipping materials in case you need them later.

Getting Started With Your System 9

Installing the Rails and System in a Rack

Once you have read the "Safety Instructions" located in the rack installation

documentation for your system, install the rails and the system in the rack.

See your rack installation documentation for instructions on installing

your system in a rack.

For a tower system, see the documentation included with your system on

installing the system stabilizer feet.

10 Getting Started With Your System

Connecting the Keyboard, Mouse, and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating which cable

to plug into each connector. Be sure to tighten the screws (if any) on the

monitor's cable connector.

Connecting the Power

Connect the system’s power cable(s) to the system.

Plug the other end of the cable into a grounded electrical outlet or a

separate power source such as an uninterrupted power supply (UPS)

or a power distribution unit (PDU).

Getting Started With Your System 11

Installing the Power Cord Retention Bracket

Attach the power cord retention bracket on the right bend of the power

supply handle. Bend the system power cable into a loop as shown in the

illustration and attach to the bracket’s cable clasp. Repeat the procedure

for the second power supply.

Turning on the System

Turn on the system and monitor (optional).

Press the power button on the system and the monitor. The power

indicators should light. Adjust the monitor’s controls until the displayed

image is satisfactory.

12 Getting Started With Your System

Installing the Bezel

Install the bezel (optional).

Complete the 0perating System Setup

If you purchased a preinstalled operating system, see the operating system

documentation that ships with your system. To install an operating system for the

first time, see the

Quick Installation Guide

. Be sure the operating system is installed

before installing hardware or software not purchased with the system.

Technical Specifications

Processor

Processor type One or two Dual-Core Intel Xeon Processors 5000

Sequence

Expansion Bus

Bus type PCI, PCI-X, PCIe

Expansion slots

PCI-X

two full-height, full-length 3.3-V, 64-bit, 133-MHz

(slots 1 and 2)

PCIe

one x8 lane, 3.3-V (slot 3)

three x4 lanes, 3.3-V (slots 4 through 6)

Getting Started With Your System 13

Memory

Architecture 533 or 667 MHz (when available) Fully Buffered

DIMMs (FBD)

Memory module sockets twelve 240-pin

Memory module capacities 256 MB, 512 MB, 1 GB, 2 GB, or 4 GB

Minimum RAM 512 MB (two 256-MB module)

Maximum RAM 48 GB

Drives

Hard drives up to ten 3.5-inch, internal, hot-plug SAS or

SATA

• eight drives in the internal drive bay

• two drives in the optional 1x2 flexbay

backplane expansion

Diskette drive one optional 3.5-inch, 1.44-MB

external optional USB 3.5-inch, 1.44-MB

Optical drive one optional

CD, DVD, or combination

CD-RW/DVD

NOTE:

DVD devices are data only.

external optional USB CD-ROM

external optional USB DVD-ROM

Flash drive external optional USB

Connectors

Back

NIC

Two TOE-capable RJ-45 (for integrated 1-GB

NICs)

Serial

9-pin, DTE, 16550-compatible

USB

Four 4-pin, USB 2.0-compliant

Video

15-pin VGA

14 Getting Started With Your System

Front

Video

15-pin VGA

USB

Two 4-pin, USB 2.0-compliant

Video

Video type ATI ES1000 video controller; VGA connectors

Video memory 16 MB of DDR SDRAM

Power

AC power supply (per power supply)

Wa tt ag e

930 W

Voltage

90–264 VAC, autoranging, 47–63 Hz

Heat dissipation

2697 BTU/hr maximum

Maximum inrush current

Under typical line conditions and over the entire

system ambient operating range, the inrush

current may reach 55 A per power supply for

10 ms or less

Batteries

System battery

CR 2032 3.0-V lithium ion coin cell

RAID battery (optional)

4.1-V lithium ion

Physical

Rack

Height

21.77 cm (8.57 in)

Width

44.27 cm (17.43 in) chassis only

48.27 cm (19 in) with rack flanges

Depth

66.13 cm (26.04 in) does not include control panel or

bezel; control panel adds an additional 1.3 cm (.51 in)

Weight (maximum

configuration)

45.36 kg (100 lb)

Connectors (continued)

Getting Started With Your System 15

Tower (without bezel)

Height

47.89 cm (18.85 in) with feet, no casters

Width

22.66 cm (8.92 in)

Depth

66.13 cm (26.04 in) does not include control panel or

bezel; control panel adds an additional 1.3 cm (.51 in)

Weight (maximum

configuration)

49.9 kg (110 lb)

Environmental

NOTE: For additional information about environmental measurements for specific

system configurations, contact your technical support provider.

Temperature

Operating

10° to 35°C (50° to 95°F)

Storage

–40° to 65°C (–40° to 149°F)

Relative humidity

Operating

20% to 80% (noncondensing) with a maximum

humidity gradation of 10% per hour

Storage

5% to 95% (noncondensing)

Maximum vibration

Operating

0.26 G from 5–350Hz for 2 min in the Z axis

Storage

1.54 G from 10–250 Hz for 15 min in all

orientations

Maximum shock

Operating

One shock pulse in the positive z axis (one pulse

on each side of the system) of 41 G for up to 2 ms

Storage

Six consecutively executed shock pulses in the

positive and negative x, y, and z axes (one pulse

on each side of the system) of 71 G for up to 2 ms

Altitude

Operating

–16 to 3,048 m (–50 to 10,000 ft)

Storage

–16 to 10,600 m (–50 to 35,000 ft)

Physical (continued)

16 Getting Started With Your System

Index 17

Index

C

combination CD-RW/DVD, 5

E

expansion-card cage, 6

I

installation and configuration, 8

integrated RAID controller, 6

M

memory, 5

interleaving, 5

N

NICs, 6

P

processors, 5

R

remote access controller

remote systems management, 6

remote access controller card, 6

remote systems management

remote access controller card, 6

S

supported Operating Systems, 7

symmetric multiprocessing

(SMP), 5

system features, 5

CD drive, 5

diskette drive, 5

DVD drive, 5

memory, 5

NICs, 6

power supply, 5

processors, 5

18 Index

system features (continued)

remote access controller card, 6

symmetric multiprocessing

(SMP), 5

USB, 6

video controller, 6

T

technical assistance, 7

technical specifications, 12

V

video controller, 6

La page charge ...

Dell PowerVault DP600 Manuel utilisateur

Ce manuel convient également à

Dell PowerVault DP600 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents