Jenn-Air JDB3200AWB3 Guide d'installation

Marque: Jenn-Air

Modèle: JDB3200AWB3

Catégorie: Lave-vaisselle

Taper: Guide d'installation

]ENN-AI _®

INSTALLATION INSTRUCTIONS

UNDERCOUNTER DISHWASHER

INSTRUCTIONSD'INSTALLATION

LAVE-VAISSELLESOUS PLAN DE TRAVAIL

Table of Contents ................................... 2

Table des matieres .................................. 26

W10208727A

Table of Confenfs

Dishwasher Safety ................................. 2

Installation Requirements ........................... 3

Tools and Parts ................................... 3

Location Requirements ............................ 4

Drain Requirements ............................... 6

Water Supply Requirements ........................ 6

Electrical Requirements ............................ 6

Installation Instructions ............................. 7

Prepare Cabinet Opening--Existing Utilities ........... 7

Prepare Cabinet Opening--New Utilities .............. 7

Prepare and Route Water Line ...................... 8

install Drain Hose ................................ 9

install Moisture Barrier (on some models) ........... 10

Prepare Dishwasher ............................. 11

Make Power Supply Cord Connection ............... 12

Installation instructions (cont.}

Determine Cabinet Opening ....................... 13

install the Door Handle (on some models) ........... 14

install Custom Panel ............................. 14

Choose Attachment Option ........................ 16

Move Dishwasher into Cabinet Opening ............. 17

Connect to Water Supply ......................... 19

Connect to Drain ................................ 20

Make Direct Wire Electrical Connection .............. 20

Secure Dishwasher in Cabinet Opening ............. 22

Complete Installation ............................. 23

Check Operation ................................. 24

If Dishwasher Does Not Operate ................... 24

Additional Tips .................................. 24

DISHWASHER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

You Need to:

, Slowly open dishwasher door while someone grasps the

rear of the dishwasher. Remove shipping materials, drain

hose and lower rack. Close dishwasher door until latched.

, Observe all governing codes and ordinances.

, install this dishwasher as specified in these instructions.

, installation should be performed by a qualified service

technician. The dishwasher must be installed to meet all

electrical and plumbing national and local codes and

ordinances.

iNSTALLATiON REQUIREMENTS

Tools and Parts

Gather the recommended tools and parts before starting

installation. Read and follow the instructions provided with

any tools listed here.

All Installations

Tools needed:

_,. _ z_..._ Flat-blade

r,,ers I screwdriver

5/16" and 1/4" _ UL listed or CSA

nut drivers or S/ approved twist-on _

hex sockets _ wire connectors* v

10" adjustable wrench 5/8" open -end

that opens to wrench

1.18" (2.9 cm) _.

If installing custom front panels,

Torx T15 screwdr ver

-Must be the proper size to connect _'our household wiring

to 16-gauge wiring in dishwasher

Other useful items you may need:

Flashlight _ Bathtowel __

Parts supplied:

I 2- Drain hose clamps I [ 2-#10x 1/2"

(1 large and 1small)silver_ Green_ Drai_ sPch_l_iwps-head77

Make sure all these parts are included in the literature package.

Parts needed:

90° Elbow,fitting with Teflon_ tape or pipe joint

3/8 N.P.T.external threads compound

(the other end must fit your

4 #10 x 1/2" wood screws (if installing custom front panels)

® Teflon is a registered trademark of E.I. Du Pont de Nemours and Company.

t® TORX is a registered trademark of Acument Intellectual Properties, LLC.

Other parts you may also need:

1_-1/2,-2,' _ I Maskingor_

(3.8t=5,0cm) I ducttap e I

screw tYpe I

c!amps (3 max)I

NOTE: Parts available for purchase in plumbing supply stores.

Check local codes. Check existing electrical supply. See

"Electrical Requirements" section. It is recommended that

electrical connections be made by a licensed electrical installer.

In addition, for first=time installations

Tools needed:

i ii _ / ii

Cordless drill

with 1/2", 3/4'!

and 1-1/2', hole

Saw bits

tubing cutter Wire stripper

Parts needed:

Copper tubing (3/8" see'Electrical Requirements" section

O D suggested) or ....

flexible braided For Direct Wire: For Power Supply

water suoo v l n_ uSe UL Listed/ cord: use UL

..... '-'-_" - CSA certified listed power

I strain;:e!iefto supp!y cord kit

ttk& fit 7/8 (2120m)PartNUmber4317824

h01e marked for uSe

-_ '' With dishwasher

Additional parts supplied with top-venting models only:

Additional parts supplied with certain models only:

und pad docated IM0!sturebarr!ertape

ok/ ........ ! I

Make sure all these parts are included in the literature package.

If parts are not included, call 1-800-688-1100.

Location Requirements

Grounded electrical supply required.

Do not run drain lines, water lines or electrical wiring where

they can interfere with or contact dishwasher motor or legs.

The location where the dishwasher will be installed must

provide clearance between motor and flooring. Motor

should not touch the floor.

Do not install dishwasher over carpeted flooring.

Shelter dishwasher and water lines leading to dishwasher

against freezing. Damage from freezing is not covered by

the warranty.

A side panel kit is available from your dealer for installing

your dishwasher at the end of your cabinetry.

A moisture barrier accessory (Part Number 4396277) is

available from your dealer for installing underneath the

countertop. Call 1=800=688=1100 to order.

Check location where dishwasher will be installed. The

location must provide:

easy access to water, electricity and drain.

convenient access for loading and unloading dishes.

Corner locations require a 2" (5.1 cm) minimum

clearance between the side of the dishwasher door

and the wall or cabinet.

square opening for proper operation and appearance.

cabinet front perpendicular to floor.

level floor. (If floor at front of opening is not level with

floor at rear of opening, shims may be needed to level

dishwasher.)

Helpful Tip: Be sure to accurately measure dimensions

and ensure dishwasher is level if the floor in the

dishwasher opening is uneven (example: Flooring

extends only partway into opening).

NOTE: To avoid shifting during dishwasher operation,

shims must be securely attached to the floor.

If dishwasher will be left unused for a period of time or in a

location where it may be subject to freezing, have it

winterized by authorized service personnel.

Make sure pipes, wires and drain hose are within the

shaded area shown in the "Product and Cabinet

Opening Dimensions" section.

Product and Cabinet Opening Dimensions

*Insulation may be compressed

(not used on al models:_

NOTE: Shaded areas of cabinet walls show where

utility connections may be installed.

*Measured from the lowest pointon the

underside of countertop. May be reduced to

33 7/8" (86 cm) by removing wheels from

dishwasher.

**Minimum, measured from narrowest point of /

opening.

Check that all surfaces have no protrusions

that would prohibit dishwasher installation.

cco

_0. /

Drain Requirements

. A new drain hose is supplied with your dishwasher.

If drain hose is not long enough, use a new drain hose

with a maximum length of 12' (3.7 m) (Part Number

3385556) that meets all current AHAM/IAPMO test

standards, is resistant to heat and detergent, and fits the

1" (2.5 cm) drain connector of the dishwasher.

Make sure to connect drain hose to waste tee or disposer

inlet above drain trap in house plumbing and 20"

(50.8 cm) minimum above the floor. It is recommended

that the drain hose either be looped up and securely

fastened to the underside of the counter, or be connected

to an air gap.

Make sure to use an air gap if the drain hose is connected

to house plumbing lower than 20" (50.8 cm) above

subfloor or floor.

Use 1/2" minimum I.D. drain line fittings.

If required, the air gap should be installed in accordance

with the air gap installation instructions. When you are

connecting the air gap a rubber hose (not provided) will

be needed to connect to the waste tee or disposer inlet.

Water Supply Requiremenfs

* A hot water line with 20-120 psi (138-862 kPa) water

pressure can be verified by a licensed plumber.

* 120°F (49°C) water at dishwasher.

* 3/8" O.D. copper tubing with compression fitting or

flexible braided water supply line (Part Number

4396897RP)

NOTE: 1/2" minimum plastic tubing is not recommended.

* A 90° elbow with 3/8" N.P.T. external pipe threads on one

end.

* Do not solder within 6" (15.2 cm) from water inlet valve.

Eiecfrical Requiremenfs

Be sure that the electrical connection and wire size are

adequate and in conformance with the National Electrical

Code, ANSl/NFPA 70 - latest edition and all local codes and

ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

You must have:

120-volt, 60 Hz, AC-only, 15 or 20 amp, fused electrical

supply.

copper wire only.

We recommend:

a time-delay fuse or circuit breaker.

a separate circuit.

if connecting dishwasher

with a power supply cord:

Use UL listed power supply cord kit (Part Number

4317824) marked for use with dishwasher.

Power supply cord must plug into

a grounded 3 prong outlet, located in

the cabinet next to the dishwasher

opening. Outlet must meet all local

codes and ordinances.

if connecting dishwasher with direct wiring:

* Use flexible, armored

or nonmetallic

sheathed, copper wire

with grounding wire

that meets the wiring requirements for your home and

local codes and ordinances.

* Use a UL Listed!CSA Certified strain relief.

iNSTALLATiON iNSTRUCTiONS

Electrical Shock Hazard

Disconnect electrical power at the fuse box or circuit

breaker box before installing dishwasher.

Failure to do so can result in death or electrical shock.

I Dis_ebo_orci_Jt I

_al!ing dishwasher.

Yes'FollOw instructi0ns in the "PrePare cab!net

Opening_Existing Utilities!! section_

NO_FollowinstruetionS n the-prepare Cabinet

Opening_New Uti!ities sectionl

_: E :isting hookups g t ity hookups

Water line

Prepare Cabinet OpeningmExisfing

Utilities

If the water line and the cable extend to the locations

shown, proceed to the "Install Drain Hose" section. If they

do not reach far enough, follow the instructions in the

"Prepare Cabinet Opening--New Utilities" section.

Prepare Cabinet OpeningmNew

Utilities

Prepare and route the electrical supply

i i i_i

Option A, Power Supply Cord:

NOTE: A grounded 3 prong outlet is required inside a

cabinet next to the dishwasher cabinet opening.

Drill a 1 1/2" (3.8 cm) hole in cabinet side or rear.

See product and cabinet opening dimensions.

Woodcabinet:Sandtheholeuntilsmooth.

Metalcabinet:Coverholewithgrommetincludedwith

powersupplycordkit.

OptionB, Direct Wire:

Helpful Tip: Wiring the dishwasher will be easier if you

route the cable into the cabinet opening from the right-hand

side.

Drill a 3/4" (1.9 cm) hole in right-hand cabinet side or rear.

See product and cabinet opening dimensions.

Wood cabinet: Sand the hole until smooth.

Metal cabinet: Cover hole with grommet (Part Number

302797 - not provided).

Route cable from power supply through cabinet hole (cable

must extend to the right front side of cabinet opening).

Tape cable to the floor in area shown. This will prohibit

cable from moving when dishwasher is moved into

cabinet opening.

Prepare and Route Wafer Line

Helpful Tip: Routing the water line through the left side

of cabinet opening will make water connection easier.

Drill a 1/2" (1.3 cm) hole in the cabinet side or rear.

Measure overall length of copper tubing or flexible

braided water supply line. Attach to the hot water line

using a connection configuration that is in compliance

with local codes and ordinances. The water line to the

dishwasher should have a manual shutoff valve.

Slowlyroutewatersupplylinethroughholeincabinet.

(Ifusingcoppertubing,itwillbendandkinkeasily,sobe

gentle.)Itshouldbefarenoughintothecabinetopening

toconnectittothedishwasherinletonthefrontleft

sideofthedishwasher.

Slowlyturnwatershutoffvalveto "ON"position.Flush

waterintoashallowpanuntilcleartogetridofparticles

thatcouldclogtheinletvalve.Turnshutoffvalveto

"OFF"position.

InstallDrain Hose

IMPORTANT: Always use a new drain hose. Check local

codes to determine if an air gap is required.

If needed, drill a 1 1/2" (3.8 cm) diameter hole in cabinet

wall or side of the opening closest to the sink.

Route drain hose as shown through hole in cabinet to the

front center of opening where drain connection will be

made. Tape drain hose to the floor in area shown. This will

prohibit it from moving when dishwasher is moved into

cabinet opening.

' option C, Waste dispose r _ with air gap

_Opt on D' No Waste d sposer-with a r gap

IMPORTANT: The drain hose connection of the disposer or

a waste tee must be made before the drain trap and at

least 20" (50.8 cm) above the floor where the dishwasher

will be installed.

Helpful Tip: To reduce vibration of the hose, keep the hose

away from the floor.

Option A, Waste disposer - no air gap

1. Using a hammer and screwdriver,

knock plug into disposer.

2. Use needle-nose pliers to remove

plug.

3. Attach drain hose to disposer inlet

with large silver drain hose clamp

(provided). Use pliers to squeeze

clamp open and move into position.

1.Connectblackendofofdrainhoseto

wasteteeandcutifneeded.

(Donotcutribbedsection.)

2.Attachblackendofdrainhosetowaste

teewithalargesilverdrainhoseclamp

(provided).Useplierstosqueezeclamp

openandmoveintoposition.Ifthedrain

hosewascut,usea11/2"to2"(3.8to

5cm)screw-typeclamp(notprovided).

OptionC,Wastedisposer- withairgap

Drain trap

1. Using a hammer and screwdriver,

knock plug into disposer.

2. Use needle-nose pliers to remove

plug.

3. Connect black end of drain hose to air

gap and cut if needed. (Do not cut

ribbed section.)

Attach drain hose to air gap with large

silver drain hose clamp (provided).

Use pliers to squeeze clamp open and

move into position. If the drain hose

was cut, use a 1 1/2" to 2" (3.8 to

5 cm) screw-type clamp (not

provided).

Use a rubber hose (not provided) with

screw-type clamps (not provided) to

connect from air gap to disposer inlet.

Option D, No waste disposer - with air gap

hose

D r

Connect black end of drain hose to air

gap and cut if needed. (Do not cut

ribbed section.)

Attach drain hose to air gap with large

silver drain hose clamp (provided).

Use pliers to squeeze clamp open and

move into position. If the drain hose

was cut, use a 1 1/2" to 2"(3.8 to 5 cm)

screw-type clamp (not provided).

Use a rubber hose (not provided) with

screw-type clamps (not provided) to

connect from waste tee to air gap.

Install Moisture Barrier

(on some models)

Moisture

barrier

1. Make sure the area under the cabinet is clean and dry

for installation of the moisture barrier.

2. Remove the backing of the moisture barrier and apply

to underside of the countertop along the front edge of

the counter.

iiii;ii_il;ii_il;iiiiii........................................................................................................;i_iiiiii_;,,,,,,,,_,i_;ii,i_;ii,i_;ii,i_;ii,i_;ii,i_;ii,i_;i_;;ii;i_;;ii;i;i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,:,i:_i;i_;;ii;_;i_;;ii;_;_;i_:_:_:_i;_;_;i_:_i;_;i_:ii,:,i:_i:i_;i;i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_ii,:,i:_:i,il

Prepare Dishwasher

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

Helpful Tip: Place cardboard under dishwasher until installed

in cabinet opemng to avoid damaging floor covering, Do not

use door panel as a work table without first covering with a

towel to avoid scratching the door panel.

Using two or more people, grasp sides of dishwasher door

frame and place dishwasher on its back.

Using a 1/4" hex head socket, nut driver or Phillips

screwdriver, remove two screws attaching access panel

and lower panel to dishwasher. Do not remove tech

sheet from access panel.

Apply Teflon ® tape or pipe joint compound to 90 °elbow

fitting (not provided). Wrap tape around coarse threads

two to four times to prohibit leaks.

Connect 90 ° elbow fitting to water inlet valve. Using a

wrench, tighten elbow until snug, and be sure that it

faces to the rear.

Using a 1/4" hex head socket, nut driver or Phillips

screwdriver, remove terminal box cover. Retain for

later use.

InstallaULListed/CSACertifiedstrainrelief.Makesure

screwheadsarefacingtotheleftwhentighteningconduit

nut.Strainreliefisprovidedwiththepowersupplycordkit.

connection will you use? |

Power Supply Cord:

Follow Option A instructions

Direct Wire'

- Follow Ophon B instructions

.................................................................................

Make Power Supply Cord Connection

Option A, Power Supply Cord:

Route cord so that it does not touch dishwasher motor

to lower part of dishwasher tub. Pull cord through strain

relief in terminal bow. Take notice when installing or

removing the dishwasher in order to reduce the chance

of damaging the power supply cord.

Select UL Listed/CSA Certified twist-on wire connectors

(included with power supply cord kit) rated to connect

your household wiring to 16-gauge dishwasher wiring.

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector

in terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in

death, fire, or electrical shock.

Remove the green grounding screw and place through

the ring terminal of the green ground wire. Reattach and

tighten the green screw.

Power Cord--Connect

remaining wires

NOTE: Twist on wire connector. Gently tug on wires to

be sure both are secured.

Connect wires black to black and white to white, using

UL Listed!CSA Certified twist-on wire connectors

(included with power supply cord kit).

L::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::LJ

Ifneeded,seewebsiteforanimatedrepresentationof

thisstep.Visitwww.jenn-air.eomunderFAQtab.

Tightenstrainreliefscrewstosecurecord.

Placewiresinsideterminalbox.Inserttabsonleftside

ofcover.Makesurewiresaretuckedinsidebox.Close

coverensuring wires are not pinched. Use 1/4" nut

driver and previously removed screw to secure cover.

NOTE: Do not plug into outlet until instructed to do so.

Defermine Cabinet Opening

Measure height of cabinet opening from underside of

countertop to floor where dishwasher will be installed

(you will need to measure the lowest point on the

underside of the countertop and the highest point on the

floor). Refer to "Dishwasher Height Adjustment Chart"

for wheel position and the number of turns needed.

Cabinetopeningheight positionWhee!" on front leg

33 7/8,(86:0cm)' I All the way up

34" 10

34 1i2;, (87:6 cm)

NOTE: If the minimum cabinet opening height is less than

34"(86.4 cm), the rear wheels can be removed for

additional clearance. This will allow the dishwasher to fit

into a 33 7/8" (86 cm) high cabinet opening, but the

dishwasher will be more difficult to move. (Measurements

are approximate. Wheels and legs are preset at the

factory for 34 1/2" [87.6 cm].)

..........Adjust wheels and legs

Turn both leveler legs to the same height. Put wheels in

the required position determined from "Dishwasher

Height Adjustment Chart."

Built-upfloors(Kitchenfloorheightishigherthan

cabinetopening.)Example:Kitchenfloortiledoesnot

extendintocabinetopening.Addshimsasneededinthe

areashowntobringthedishwasherupto34"(86.4cm)

belowthecountertop.

NOTE:Shimsmustbesecurelyattachedtofloortoavoid

movementwhenthedishwasherisinuse.

Install the Door Handle

(on some models)

Mounting

stud

, Setscrew

(in bottom

of handle)

Allen wrench

IMPORTANT: Do not scratch the front panel during this

procedure.

Remove the door handle and hardware bag containing

the setscrews and Allen wrench from the cardboard box.

Setscrews are already installed in the handle. Place

handle on mounting studs with the setscrews facing

down. Push the door handle tightly against the door.

Insert the short end of the Allen wrench into the

setscrews. Tighten the setscrews 1/4 turn past snug.

Retain Allen wrench with Installation Instructions.

Install Custom Panel

(Model JDB3600AWX)

NOTE: The handle for the custom panel is not included.

IMPORTANT: If the handle is attached from the back of

the custom panel, the screw holes should be countersunk

for the screws heads to be flush with the panel. If the

handle is attached to the front of the custom panel, the

screw lengths cannot exceed the panel thickness. For

more information on Jenn-Air custom handle selection,

refer to the Jenn-Air Catalog, visit www.jenn-air.com, or

call 1-800-688-1100.

NOTE: A customer-supplied full front panel must weigh

no more than 16 Ibs (7.3 kg) and must be made to

specific dimensions. It is recommended that a

cabinetmaker cut the custom panel because of the

precise dimensions needed.

NOTE: All mounting hardware supplied is for a 3/4"

(19.1 mm) thick wood panel. If a thinner wood panel, or

materials other than wood are used, it is the customer's

responsibility to obtain the proper length screws and

adjust the pilot holes accordingly.

IMPORTANT: Use a moisture-resistant sealer on both

sides and all edges of the panel to avoid damage from

humidity.

........1-1........

-:J Dishwashers with control |

panel on the top |

3/4" (19.1 mm)

*This dimension is for 4" (10.2 cm) toe kick. If the

installation needs a higher toe kick, adjust the height

of the wood panel accordingly. Not recommended for

toe kicks greater than 6" (15.2 cm).

With a TORX _)screwdriver, remove three screws from both

sides, as shown; hold the outer panel up while removing

the screws. Save screws for reinstallation.

Dishwashers with control panel on

P P

....j

3 screws

per side

outer [

Gently set outer panel aside. Lay the customer-supplied

custom panel face down on a covered, non-scratching

surface.

Mark line

9 29/32"

(25.2 cm)

p edge

Measure 9 29/32" (25.2 cm) from top edge and mark a line

on the back of customer-supplied custom panel. Position the

outer panel on the back of the customer-supplied custom

panel as shown, so that the top holes in the outer panel are

on the line, and both panels are centered side to side.

Mark pilot

holes

Mark all four hole locations; remove outer panel. Drill 3/32"

pilot holes 1/2" (13 mm) deep in customer-supplied custom

panel. Place the outer panel on the back of the customer-

supplied custom panel; align holes.

Attach outer panel to back of customer-supplied custom

panel with the four #10-16 x 3/8" hex head screws supplied

in the literature package. Attach the handle. The handle

should be centered on the front of the customer-supplied

custom panel in the area shown.

IMPORTANT: Screw heads must be flush with back of

customer-supplied custom panel.

3 screws

each side

top

edges

Customer-supplied

panel

Attach the panel assembly to the door by reinstalling the

three screws on each side; do not tighten completely. This

reinstallation of the three screws will hold the panel

assembly in place on the door frame,

Customer-supplied

panel

edges

i Drillthrough

these holes

Align the top edge of the customer-supplied custom

panel with the top of the console.

Drill two 3/32" pilot holes 1/2" (13 mm) deep, into the

customer-supplied custom panel, through the holes in the

top corners on the inner panel, as shown.

edges

:)rill through

these holes

Customer-supplied

panel

Install the two #8-18 x 1 3/8" screws from

the literature package in the top corners of the inner

panel. Tighten the six side screws reinstalled in Step 6.

Choose Affechmenf Option

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

Using two or more people, stand the dishwasher up.

Option 1, Countertop attachment:

IMPORTANT: The dishwasher must be secured to the

cabinet. There are two brackets on top of the dishwasher

that can be attached to the countertop if it is wood,

laminate or other similar surfaces. If your countertop is

marble, granite or other hard surface, the brackets may

be moved to the sides of the dishwasher.

NOTE: Do not attach the dishwasher. This will be done

later.

Option 2, Dishwasher side attachment:

tabs

To remove the brackets from the top, flatten tab at back

of brackets with pliers, and pull the brackets out of the

slots.

Break off the end of the bracket along the scored line.

With another person holding the rear of the dishwasher

to keep it from tipping, open dishwasher door and place

towel over pump assembly and spray arm of dishwasher.

This will keep screws from falling into pump area when

you are securing dishwasher to cabinet.

plastic

button

Push the plastic buttons out of the side of the tub.

NOTE: Save the buttons to cover the holes after

dishwasher is installed.

Pushbracketintoslotonthesideofdishwasher,and

bendtabintowardthesideofthedishwashersothatit

keepsthebracketinplace.Repeatthisstepfortheother

sideofthedishwasher.

NOTE:Donotattachthedishwasher.Thiswill bedone

later.

Move Dishwasher into Cabinet

Opening

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

Using two or more people, stand dishwasher upright.

NOTE: Do not install kickplate until instructed to do so.

iMPORTANT: Double-check correct placement of utilities.

Grasp the sides of the dishwasher at the edges of the

door panel. Tilt dishwasher backward on wheels and

move dishwasher close to cabinet opening.

NOTE: Do not push on the front of the panel or on the

console. Panel or console may dent.

Helpful Tip: Temporarily tape utilities to the floor in the

locations shown to prohibit them from moving when

dishwasher is moved into the cabinet opening.

Check that water line is on the left side of opemng and

drain hose is near the center of the cabinet opening.

With another person holding the dishwasher to avoid it

from tipping, open and close the door a few times. If the

door closes or falls open under its own weight, the door

tension will need to be adjusted.

ssdng

.nsioner _ o

To adjust the door spring tension, unhook the spring

from the rear leg of dishwasher.

Using a 5/16" nut driver or hex socket, remove the screw

from the tensioner.

The screw can be put into one of three holes Inl,[],_31

in the front leg of dishwasher. If the door closes by itself,

move the tensioner to a higher number hole and replace

screw. Reattach door spring to rear leg.

NOTE: Tensioners on both sides of dishwasher should be

secured at same holes.

When door is unlatched, and door opens by itself, move

the tensioner to a lower numbered hole and replace the

screw. Reattach door spring to rear leg.

NOTE: Tensioners on both sides of dishwasher should

be secured at same holes.

Insulation

blanket

IMPORTANT: If wheels were removed, avoid damage to

the floor when moving the dishwasher. Slowly move

dishwasher completely into cabinet opening. Do not kink

or pinch water line, drain hose, power supply cord or

direct wire between dishwasher and cabinet. Remove

cardboard from under dishwasher.

NOTE: It is all right if dishwasher fits tightly into cabinet

opening. Do not remove insulation blanket-the blanket

reduces the sound level.

NOTE: If using power cord, make sure to route end

through hole in cutout before sliding dishwasher into

cabinet opening.

Align front of dishwasher door panel with front of

cabinet doors. You may need to adjust alignment to be

even with your cabinets.

Check that leveling legs are firmly against the floor.

Close and latch the door, and place level against the

front panel. Check that dishwasher is centered from front

to back in the opening. If needed, adjust leveling leg until

dishwasher is plumb. Repeat for other side of dishwasher.

Helpful Tip: Push up on front of dishwasher to raise

dishwasher offthe ground to adjust front legs. With

some installations, it may be easier to adjust the front leg

using the 3/16" hex head socket or adjustable wrench.

Place level against top front opening of tub. Check that

dishwasher is level from side to side. If dishwasher is not

level, adjust front legs up or down until dishwasher is

level.

ii iiii

Connect to Water Supply

Copper tubing only: Slide nut then ferrule onto copper

tubing about 1" (2.5 cm).

NOTE: To avoid vibration during operation, route the

water supply line so that it does not touch the

dishwasher base, frame or motor.

Copper tubing only: Put the tubing into the 90° elbow

fitting as far as it will go (the copper tubing bends and

kinks easily). Slide the nut and ferrule forward and start

the nut onto the elbow threads.

Flexible braided connection: Secure nut to elbow using

5/8" open ended wrench or adjustable wrench.

NOTE: Do not use Teflon ®tape with compression fittings.

Hold the 90° elbow fitting still with one adjustable wrench

and tighten the nut with second adjustable wrench.

Helpful Tip: For easier access, use a 5/8" open ended

wrench to tighten connection.

Place paper towel under 90° elbow fitting. Turn on water

supply and check for leaks. If leak occurs, repeat

previous step.

If needed, see website for animated representation

of this step. Visit www.jenn-air.com/watersuppl¥ under

FAQ tab.

_1__i_iiiiiiiiii_i_ ¸il¸ii_ii_i_iiiii_i_ii_ii'ii¸I¸ii'ii¸I¸ii'ii¸I¸ii'ii¸I¸ii'ii_iii'i'ii_i_i_ii_iiiiiiiiiiiiiii/i/iiiiiiii_ii}iiii_i_ii}iiii_i_ii}iiii_i_ii}iiii_i_ii}iiii_i_ii}iiii_i_ii}iiii_i_ii}iiii_i_ii}iiii_i_ii}iiii_i_ii}iiii_i_ii}iiii_i_ii}iiii_i_ii}iiii_i_ii}iiii_i_ii}iiii_i_ii}iiii_i_ii}iiii_i_ii}iiii_i_ii}iiiiiiiiiiiiiiii:_ii_iiiiiiiiiiiiiiiiiiiii

Connect to Drain

1_ Connect drain hose

Green clamp

Black drain hose

connector--

Place towel under drain hose to catch any water in drain

hose. Place the small green drain hose clamp onto the

small end of the drain hose. Push the new drain hose

into the black drain hose connector up to the drain hose

stop.

Using pliers, squeeze open the small green drain hose

clamp and slide onto connector between stops.