Delta Faucet T14278-LHP Guide d'installation

48312 48312 48312 48312

IMPORTANT DOCUMENTS ENCLOSED

CAUTION:

To reduce the risk of injury due to hot water

burns, make sure the enclosed labels are

applied where specified on the label.

DOCUMENTOS IMPORTANTES INCLUIDOS

AVISO:

Para reducir el riesgo de lesión por

quemaduras de agua caliente, asegúrese que

las etiquetas incluidas se han aplicado donde

se ha especificado en la etiqueta.

DOCUMENTS IMPORTANTS À L’INTÉRIEUR

MISE EN GARDE :

P

our réduire le risque d’ébouillantage, veuillez

apposer les étiquettes fournies aux endroits

indiqués sur celles-ci.

48312 48312 48312 48312

3/7/07 48312 Rev C

NOTICE TO INSTALLER: Place this label on the water heater next

to the temperature adjustment knob.

WARNING:

These series of tub/shower valves do not adjust automatically

for changes in temperature at the hot water heater or inlet. If the

temperature setting of the hot water heater or inlet is changed, the setting

on these valves must be adjusted manually! Failure to re-adjust the valve

may result in hot water burns or extreme cold resulting from variations in

line pressure (such as when a dishwasher or washing machine is in use

while you are taking a shower). After installation, verify that the rotational

limit stop (13/14/17 series) or temperature knob (17T series) on the valve

is set so that changes in line pressure or temperature do not result in

uncomfortable water temperature changes. If the temperature setting of

the hot water heater or inlet is changed after installation of the valve,

the setting of the rotational limit stop or temperature knob also must

be changed! Consult the installation instruction sheet for instructions on

how to make this setting, or call us at 1-800-345-DELTA.

AVISO AL INSTALADOR: Coloque esta etiqueta en el calentador

de agua al lado de la perilla para el ajuste de temperatura.

AVISO:

Esta serie de válvulas para bañeras/regaderas no se ajustan automáti-

camente a los cambios de temperatura en el calentador de agua o en

el agua de entrada. Si el ajuste de la temperatura del calentador de agua

o la temperatura del agua que entra cambia ¡El ajuste de estas válvulas

se debe hacer manualmente! El no reajustar la válvula puede resultar en

quemaduras por agua caliente o temperaturas de agua extremadamente

frías resultando en variaciones de presión y temperatura (como cuando el

fregador de platos o la lavadora están funcionando mientras que se baña).

Después de la instalación, verifique que el control o tope del límite rotacional

(series 13/14/17) o la perilla del control de temperatura (series 17T ) en la

válvula está ajustada para que los cambios de presión y de temperatura

en la línea no resulten en cambios incómodos de temperatura del agua. Si

el ajuste de la temperatura del calentador de agua o de la entrada de

agua se cambia después de la instalación de la válvula, el ajuste del

tope del límite rotacional o la perilla de ajuste ¡también se debe cam-

biar! Consulte con su hoja de instrucciones de instalación para saber como

se ajusta o cambia el ajuste, o llámenos al 1-800-345-DELTA.

AVIS À L’INSTALLATEUR: Fixez cette étiquette sur le chauffe-eau

près du bouton de réglage de température.

ATTENTION :

La soupape de robinet de baignoire ou de douche de cette série ne se

règle pas automatiquement en fonction des changements de température

de l’eau chaude au chauffe-eau ou de l’eau d’alimentation. En cas de

modification du réglage de température du chauffe-eau ou de la température

de l’eau d’alimentation, le réglage de cette soupape doit être modifié

manuellement! Si le réglage de la soupape n’est pas modifié, le robinet pourra

permettre l’écoulement d’eau très chaude susceptible de causer l’ébouillantage

ou d’eau très froide, sous l’effet des variations de pression et de température

dans la tuyauterie d’alimentation (lorsque la douche est utilisée en même temps

que le lave-vaisselle ou la machine à laver, par exemple). Après l’installation,

assurez-vous que la butée de température maximale (séries 13/14/17) ou le

bouton de température (séries 17T) sur la soupape est réglé de manière que

les fluctuations de pression et de température dans la tuyauterie d’alimentation

n’entraînent pas de changements de température de l’eau inconfortables. En

cas de modification du réglage de température du chauffe-eau ou de la

température de l’eau d’alimentation après l’installation de la soupape, le

réglage de la butée de température maximale ou du bouton de température

doit être modifié! Pour régler le bouton de température, consultez la feuille

d’instructions d’installation ou appelez-nous au 1-800-345-DELTA.

3/7/07 48312 Rev C

BY/POR/PAR _______________ COMPANY/COMPANIA/COMPAGNIE ________________

DATE/FECHA/LE ___________ PHONE/TELÉFONO/TELÉPHONE _______________

_____

NOTICE TO INSTALLER: Place this label close to the valve where the owner

will see it, such as inside the door of a cabinet or vanity.

WARNING:

Water temperature changes due to seasonal or other inlet variations, such as changing the setting

on the hot water heater may require adjustment of the rotational limit stop (13/14/17 Series) or

temperature knob (17T Series) on your tub/shower valve to ensure a safe maximum temperature.

These valve series do not automatically adjust for inlet temperature changes. If changes occur and

you are not sure how to make the necessary rotational limit stop or temperature knob adjustments,

please consult the installation instruction sheet provided with this valve or call 1-800-345-DELTA.

These valve series are designed to minimize the effects of outlet water temperature changes

due to inlet pressure changes, commonly caused by dishwashers, washing machines, toilets and

the like. They may not provide protection from hot water burns when there is a failure of

other temperature controlling devices elsewhere in the plumbing system. After making the

necessary adjustments please fill in the information below. This valve/system has been set by the

person listed below to ensure a safe maximum temperature. Any change in the setting may raise

the discharge temperature above the limit considered safe and could lead to hot water burns. If

this label has not been completed, you should verify that the rotational limit stop or temperature

knob has been properly adjusted to suit your individual installation. The installation instruction sheet

supplied with the valve provides information on how to make this setting.

AVISO AL INSTALADOR: Coloque esta etiqueta cerca de la válvula donde el

propietario la pueda ver, tal como dentro de la puerta del gabinete o el tocador.

AVISO:

Los cambios de temperatura del agua por variaciones estacionales u otras variaciones en el agua

de entrada, como el cambio por el ajuste en el calentador de agua, puede requerir el ajuste del

tope del límite rotacional (Series 13/14/17) o ajuste de la perilla para el control de la temperatura

(Series 17T) de la válvula de su unidad bañera/regadera para asegurar una temperatura máxima

segura. Esta serie de válvulas no se ajusta automáticamente para los cambios de temperatura del

agua de entrada. Si cambios ocurren y usted no está seguro como hacer los ajustes necesarios

con la perilla para controlar la temperatura, por favor consulte la hoja de instrucciones de

instalación proporcionada con esta válvula o llámenos al 1-800-345-DELTA. Las válvulas de esta

serie están diseñadas para minimizar los efectos por cambios de temperatura en el agua de

entrada por cambios en la presión del agua, comúnmente causados por el uso simultáneo de

fregadoras de platos, lavadoras, inodoros y aparatos similares. Estas pueden no proporcionar

protección de quemaduras por el agua caliente cuando hay una falla de otros mecanismos

que controlan la temperatura del agua en otro sitio del sistema de plomería. Después de

hacer los ajustes necesarios, por favor escriba la información suministrada a continuación. Esta

válvula/sistema ha sido ajustada por la persona indicada a continuación para ayudar a asegurar

una temperatura máxima segura. Cualquier cambio al ajuste puede aumentar la temperatura del

agua de descarga sobre el límite considerado seguro y puede resultar en quemaduras por agua

caliente. Si esta etiqueta no se ha llenado, debe verificar si el control o tope del límite rotacional o

la perilla que controla la temperatura han sido correctamente ajustadas al gusto de su instalación

individual. La hoja de instrucciones de instalación proporcionada con las válvulas le suministra

información sobre como hacer este ajuste.

AVIS À L’INSTALLATEUR: Fixez cette étiquette près du robinet, à la vue du

propriétaire, à l’intérieur de la porte du meuble ou de la coiffeuse, par exemple.

ATTENTION :

Les modifications de la température de l’eau attribuables au changement de saison ou à d’autres

facteurs, comme la modification du réglage du chauffe-eau, peuvent nécessiter un réglage de la

butée de température maximale (séries 13/14/17) ou du bouton de température (séries 17T) de la

soupape de votre robinet pour baignoire et de douche. La soupape de robinet de ces séries ne se

règle pas automatiquement en fonction des changements de température de l’eau chaude de l’eau

d’alimentation. En cas de modification de la température de l’eau d’alimentation, si vous ne savez

pas comment régler la butée de température maximale ou le bouton de température, veuillez con-

sulter le feuillet d’instructions d’installation fourni avec la soupape ou appeler au 1-800-345-DELTA.

La soupape de cette série est conçue pour limiter la variation de la température de l’eau pouvant

résulter des fluctuations de température et de pression dans la tuyauterie d’alimentation. Ces fluc-

tuations sont habituellement causées par une utilisation simultanée du lave-vaisselle, de la machine

à laver, d’un cabinet d’aisances ou d’un autre appareil qui consomme de l’eau. La soupape peut

ne pas protéger l’utilisateur contre l’ébouillantage en cas de défectuosité d’un autre dis-

positif de régulation de la température de l’eau situé ailleurs dans la tuyauterie. Après avoir

effectué les réglages nécessaires, veuillez inscrire l’information requise ci-dessous. Cet appareil

de robinetterie a été réglé par la personne dont le nom figure ci-dessous pour que la température

maximale de l’eau soit sans danger. Toute modification du réglage peut occasionner une élévation

de la température de l’eau à la sortie du robinet et l’eau qui s’écoulera pourra être suffisamment

chaude pour causer l’ébouillantage. Si la présente étiquette n’a pas été remplie, assurez-vous

que la butée de température maximale ou le bouton de température a bien été réglé en fonction

des caractéristiques de votre installation. La marche à suivre pour faire le réglage figure dans les

instructions d’installation fournies avec la soupape.

TO BE FILLED OUT BY THE INSTALLER / PARA SER LLENADO POR EL INSTALADOR /

A REMPLIR PAR L’INSTALLATEUR:

Rotational Limit Stop is

located behind the disc.

13 / 14 Series

17 Series

Hotter

Más

Caliente

Plus

Chaud

1st Position

Primera Posición

1ère Position

17T Series

Hotter

Más

Caliente

Plus

Chaud

Colder

Más

F

ría

Plus

F

roid

13 / 14 Series

17 Series

Hotter

Más

Caliente

Plus

Chaud

Hotter

Más

Caliente

Plus

Chaud

Colder

Más

F

ría

Plus

F

roid

1st Position

Primera Posición

1ère Position

Temperature Knob

Po

mo para el ajuste

d

e temperatura

Bouton de Température

17T Series

Temperature Knob

Po

mo para el ajuste

d

e temperatura

Bouton de Température

Rotational Limit Stop is

located behind the disc.

MultiChoice™ Valve Trim

Installation Instructions

Ow

ners Manual

13/14, 17 & 17T

Series

Write purchased model number here.

U.S. Patents: 4,043,359, 3,786,995, 4,562,960,

4,593,430, 4,089,347, 4,218,785, 4,696,322,

4,765,365. More patents are pending.

ASME A112.18.1 / CSA B125.1

ASSE 1016

®

U

P

C

Table of Contents:

Warranties .......................................................................... Page 2

13/14 Series Installation Instructions .................................. Pages 3 - 6

17 Series Installation Instructions ....................................... Pages 7 - 10

17T Series Installation Instructions ......................................Pages 11-14

Maintenance ....................................................................... Pages 14-15

Cartridge Summary Reference Sheet ................................. Page 16

Replacement Parts ............................................................. Pages 17 - 33

1

You May Need

T

E

F

L

O

N

3/7/07

48312 Rev. C

THIS VALVE MEETS OR EXCEEDS THE

FOLLOWING STANDARDS:

ASME A112.18.1/CSA B125.1 and ASSE 1016.

CAUTION: This system/device must be set by the

installer to ensure safe, maximum temperature.

Any change in the setting may raise the discharge

temperature above the limit considered safe and

may lead to hot water burns.

NOTICE TO INSTALLER: CAUTION!–As the

installer of this valve, it is your responsibility

to properly INSTALL and ADJUST this valve

per the instructions given. This valve does

not automatically adjust for inlet temperature

changes, therefore, someone must make the

necessary Rotational Limit Stop or temperature

knob adjustments at the time of installation and

further adjustments may be necessary due to

seasonal water temperature change. YOU MUST

inform the owner/user of this requirement by

following the instructions. If you or the owner/

user are unsure how to properly make

these adjustments, please refer to

page 5 (13 / 14 series), page 10 (17 series) or

page 14 (17T series) and if still uncertain, call us

at 1-800-345-DELTA.

After installation and adjustment, you must afﬁx

your name, company name and the date you

adjusted the Rotational Limit Stop or temperature

knob to the caution label provided and apply or

attach the label to the back side of the closest

cabinet door and the warning label to the water

heater. Leave this Instruction Sheet for the

owner’s/user’s reference.

WARNING: This pressure balanced or

thermostatic bath valve is designed

to minimize the effects of outlet water

temperature changes due to inlet pressure

changes, commonly caused by dishwashers,

washing machines, toilets and the like. It may

not provide protection from hot water burns

when there is a failure of other temperature

controlling devices elsewhere in the

plumbing system, if the rotational limit stop

or temperature knob is not properly set or if

the hot water temperature is changed after the

settings are made or if the water inlet changes

due to seasonal changes.

WARNING: Do not install a shut-off device on

either outlet of this valve. When this type of

device shuts off the water ﬂow, it can defeat

the ability of the valve to balance the hot and

cold water pressures.

All parts and ﬁnishes of the Delta® faucet are

warranted to the original consumer purchaser to

be free from defects in material & workmanship

for as long as the original consumer purchaser

owns their home. Delta Faucet Company

recommends using a professional plumber for all

installation & repair.

Delta will replace, FREE OF CHARGE, during

the warranty period, any part or ﬁnish that proves

defective in material and/or workmanship under

normal installation, use & service. Replacement

parts may be obtained by calling 1-800-345-

DELTA (in the U.S. and Canada) or by writing to:

In the United States:

Delta Faucet Company

Product Ser

vice

55 E. 111th Street

Indianapolis, IN 46280

In Canada:

Delta F

aucet Canada

Technical Service Centre

420 Burbrook Place

London, ON N6A 4L6

This warranty is extensive in that it covers

replacement of all defective parts and even

ﬁnish, but these are the only two things that

are covered. LABOR CHARGES AND/OR

DAMAGE INCURRED IN INSTALLATION,

Lifetime Faucet and Finish Limited Warranty

REPAIR, OR REPLACEMENT AS WELL AS ANY

OTHER KIND OF LOSS OR DAMAGES ARE

EXCLUDED. Proof of purchase (original sales

receipt) from the original consumer purchaser

must be made available to Delta for all warranty

claims. THIS IS THE EXCLUSIVE WARRANTY

BY DELTA FAUCET COMPANY, WHICH DOES

NOT MAKE ANY OTHER WARRANTY OF ANY

KIND, INCLUDING THE IMPLIED WARRANTY

OF MERCHANTABILITY.

This warranty excludes all industrial, commercial

& business usage, whose purchasers are

hereby extended a ﬁve year limited warranty

from the date of purchase, with all other terms of

this warranty applying except the duration of the

warranty. This warranty is applicable to Delta®

faucets manufactured after January 1, 1995.

Some states/provinces do not allow the exclusion

or limitation of incidental or consequential

damages

, so the above limitation or exclusion

may not apply to you. Any damage to this faucet

as a result of misuse, abuse, or neglect, or any

use of other than genuine Delta® replacement

parts WILL VOID THE WARRANTY.

This warranty gives you speciﬁc legal rights, and

you may also have other rights which vary from

state/province to state/province. It applies only for

Delta® faucets installed in the United States of

America, Canada, and Mexico.

All parts of the Delta HDF faucet are warranted to

the original consumer purchaser to be free

from defects in material and workmanship for a

period of ﬁve (5) years. This warranty is made

to the original consumer purchaser and shall be

effective from date of purchase as shown on

purchaser’s receipt.

Delta will replace, FREE OF CHARGE, during

the warranty period, any part which proves

defective in material and/or workmanship

under normal installation, use and service.

Replacement parts can be obtained from your

local dealer or distributor listed in the tele-

phone directory or by returning the part along

with the purchaser’s receipt to our factory,

TRANSPORTATION CHARGES PREPAID,

at the address listed.

THIS WARRANTY IS THE

ONLY EXPRESS WARRANTY MADE BY DELTA.

ANY CLAIMS MADE UNDER THIS WARRANTY

MUST BE MADE DURING THE FIVE YEAR

PERIOD REFERRED TO ABOVE. ANY IMPLIED

WARRANTIES, INCLUDING THE IMPLIED

WARRANTY OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE, ARE

LIMITED IN DURATION TO THE DURATION OF

THIS WARRANTY. LABOR CHARGES AND/OR

DAMAGE INCURRED IN INSTALLATION,

REPAIR OR REPLACEMENT AS WELL AS

INCIDENTAL AND CONSEQUENTIAL

DAMAGES CONNECTED THEREWITH ARE

EXCLUDED AND WILL NOT BE PAID BY DELTA.

Some states do not allow limitations on how long

an implied warranty lasts, or the exclusion or

limitation of incidental or consequential damages,

so the above limitations or exclusions may not

apply to you.

This warranty gives you speciﬁc legal rights, and

you may also have other rights which vary from

state to state.

This warranty is void for any damage to this faucet

due to misuse, abuse, neglect, accident, improper

installation, any use violative of instructions

furnished by us or any use of replacement parts

other than genuine Delta parts.

Delta HDF Limited Warranty

2

13 / 14 Series Installation

1

Cartridge Installation

A.

C.

Turn off water supplies. Remove

cover (1), bonnet nut (2) and test cap (3)

from the body. If this is not a thin wall

mounting, the entire plasterguard (4)

may be removed. If screen (5) is in place,

remove before installing cartridge.

For back to back or reverse installations

(hot on r

ight and cold on left) insert the

cartridge with the “hot side” on the right.

If you are not making a reverse or back

to back installation skip this step and

continue with step 1C.

Slide bonnet nut (1) over the cartridge

and thread onto the body. Hand tighten

securely.

B.

Rotate the cartridge (1) so the words

“hot side” (2) appear on the left. Insert

cartridge into valve body as shown. Make

sure the cartridge tubes and O-rings (3)

are properly seated in holes at the base of

the body. Ensure the keys on the body are

fully engaged with the slots in the body (4).

Back to back Installation

Normal Installation (changes not required)

Reverse

Installation

Cold

Hot

1

2

3

1

4

2

3

1

3

5

4

13 / 14 Series Installation

2

Showerhead and Tub Spout Installation

FOR SHOWERHEAD INSTALLATION:

Connect top outlet (1) to shower arm (2)

with proper ﬁttings. To prevent damage

to ﬁnish on shower arm, insert wall end

of shower arm into shower ﬂange (3)

before screwing arm into riser connection.

Thread showerhead (4) onto shower

arm. Apply Teﬂon

®

tape to pipe threads on

both ends. Do not overtighten

showerhead.

A.

3

2

1

Slip-On Installation

The copper tube (1) must be 1/2” nominal

copper. Important: If it is necessary to cut

the copper tube, the end must be cham-

fered free of burrs to prevent cutting or

nicking O-ring inside the spout. Slide spout

over copper tube ﬂush with the ﬁnished tub

or wall surface. Tighten set screw (2), but

do not overtighten.

4

1

4

FOR TUB SPOUT INSTALLATION:

Refer to the installation instructions supplied with your spout. Do not connect deck mount

spouts to in-wall valves. Do not use hand showers connected in lieu of a tub spout to a

tub/shower valve. Do not use PEX tubing for tub spout drop.

B-1

B-2

B-3

Iron Pipe Installation

Install threaded pipe nipple (1) to extend

past ﬁnished wall. Apply Teﬂon

®

tape to

threads on pipe nipple and screw on

tub spout.

Copper Sweat Installation

Remo

ve O-ring (1) from adapter (2). Solder

adapter to tube taking care to keep solder

away from O-ring groove. CAUTION: NO

SOLDER PERMITTED ON OUTSIDE

DIAMETER OF AD

APTER ADJACENT

TO O-RING GROOVE. Cut off tube (3) and

replace O-ring on groove of brass adapter.

Thread tub/spout onto adapter, taking care

not to damage O-ring, and hand tighten until

spout is ﬁrmly against ﬁnished wall and all

slack is taken up behind wall.

2

1

2

3

5

13 / 14 Series Installation

3

Adjusting the Rotational Limit Stop

IMPORTANT:

The Rotational Limit Stop is used to limit the

amount of hot water a

vailable such that, if set

properly, the user will not be scalded if the han-

dle accidentally is rotated all the w

a

y to “hot”

when a person is showering or ﬁlling a tub. The

ﬁrst position allows the LEAST amount of hot

w

ater to mix with the cold water in the system.

In the ﬁrst position the water will be the coldest

possible when the handle is turned all the way

to hot. As you move the Rotational Limit Stop

counterclockwise, you progressively add more

and more hot water in the mix. The last position

to the left will result in the greatest amount of

hot water to the mix, and the greatest risk of

scald injury if someone accidentally turns the

valve handle all the way to the hot side while

showering or ﬁlling a tub.

WARNING: In some instances, setting the

Rotational Limit Stop in the hottest position

(full counter

clockwise) could result in scald

injury. It is necessary to adjust the Rotation-

al Limit Stop so that the water coming out

of the v

alve will not scald the user when the

handle of the valve is rotated to the hot side.

• According to the majority of industry stan-

dards

, the maxim

um allowable temperature of

the water exiting the valve is 120°F (Your local

plumbing codes may require a water tempera-

ture less than 120°F).

•

The Rotational Limit Stop ma

y need to be re-

adjusted seasonally if the inlet water tempera-

ture changes.

For example, during the winter,

the cold water temperature is colder than it is

during the summer which could result in vary-

ing outlet temper

atures. A water temperature

for a comfortable bath or shower is typically

between 90°F - 110°F.

• Run the water so that the cold water is as

cold as it will get and hot water is as hot as

it will get. Place the handle on the stem (see

page 6, step 4D) and rotate the handle coun-

tercloc

kwise until the handle stops

.

• Place a thermometer in a plastic tumbler

and hold in the water stream. If the water

temperature is above 120°F, the Rotational

Limit Stop must be repositioned clockwise to

decrease valve outlet water temperature to

be less than 120°F or to meet the require-

ments of y

our local plumbing codes.

• To adjust the temperature of the water

coming out of the valve, pull the disc back to

a position where it is possible to remove the

Rotational Limit Stop and readjust the teeth

engagement position to the desired tem-

per

ature

. Clockwise will decrease the outlet

temperature, counterclockwise will increase

the outlet temperature. Temperature change

per tooth (notch) could be 4° - 16°F based on

inlet w

ater conditions

. Repeat as necessary.

Push disc until fully seated.

W

ARNING:

Failure to re-install Disc after

setting Rotational Limit Stop could result

in scald injur

y

.

• MAKE SURE COLD WATER FLOWS

FROM THE VALVE FIRST. MAKE SURE

WATER FLOWING FROM THE VALVE

A

T THE HOTTEST FLOW POSSIBLE

DO

ES NOT EXCEED 120°F OR THE

MAXIMUM ALLOWED BY YOUR LOCAL

PLUMBING CODE.

1st Position

Hotter

Rotational Limit Stop

Stem

Disc

13 / 14 Series Installation

4

Trim Installation

C.

D.

A.

B.

Slide O-ring (1) over cartridge and the

bonnet nut (2). The O-ring, which acts as

a spacer to steady the sleeve, should rest

behind the bonnet nut.

If your model requires a spacer (1), insert

it into the sleeve (2) and push it to the

front. Slide the sleeve over the cartridge,

body and O-ring.

Secure the escutcheon (1) and backplate

(2) (if your model has one) to the bracket

(3) using the 2 screws provided (4). Do not

overtighten escutcheon screws.

Using an Allen wrench to secure the set

scre

w, install the handle onto the stem.

1

2

1

2

1

2

3

4

6

1

Cartridge Installation

A.

17 Series Installation

C.

Turn off water supplies. Remove

cover (1), bonnet nut (2) and test cap (3)

from the body. If this is not a thin wall

mounting, the entire plasterguard (4)

may be removed. If screen (5) is in place,

remove before installing cartridge.

B.

Rotate cartridge (1) so the words

“HOT SIDE” (2) appear on the left. Insert

cartridge assembly into valve body.

Make sure the key (3) on the cartridge is

fully engaged with the slot in the brass

body (4). Slide bonnet nut (5) over the

cartridge and thread onto the body.

Hand tighten securely.

1

2

3

1

2

1

3

4

7

5

2

3

Insert adapter assembly (1) into valve

body. Make sure the adapter assembly

is correctly positioned and is pressed all

the way down inside body. Secure adapter

with the screw (2) provided in the adapter

assembly. Remove the retainer (3) from

the adapter.

For back to back or reverse installations

(

hot on right and cold on left): Rotate

cartridge (1) so the words “HOT SIDE” (2)

appear on the right. Install the cartridge

making sure that the key is fully engaged

with the slot in the brass body (See step C).

Slide bonnet nut (3) over the cartridge and

thread onto the body. Hand tighten securely.

Back to back Installation

Reverse

Installation

Cold

Hot

1

3

Normal Installation

(changes not required)

2

5

4

17 Series Installation

8

2

Showerhead and Tub Spout Installation

FOR SHOWERHEAD INSTALLATION:

Connect top outlet (1) to shower arm (2)

with proper ﬁttings. To prevent damage

to ﬁnish on shower arm, insert wall end

of shower arm into shower ﬂange (3)

before screwing arm into riser connection.

Thread showerhead (4) onto shower

arm. Apply Teﬂon

®

tape to pipe threads on

both ends. Do not overtighten

showerhead.

A.

3

2

1

Slip-On Installation

The copper tube (1) must be 1/2” nominal

copper. Important: If it is necessary to

cut the copper tube, the end must be

chamfered free of burrs to prevent cutting

or nicking O-ring inside the spout. Slide

spout over copper tube ﬂush with the

ﬁnished tub or wall surface. Tighten set

screw (2), but do not overtighten.

4

1

FOR TUB SPOUT INSTALLATION:

Refer to the installation instructions supplied with your spout. Do not connect deck mount

spouts to in-wall valves. Do not use hand showers connected in lieu of a tub spout to a

tub/shower valve. Do not use PEX tubing for tub spout drop.

B-1

B-2

B-3

Iron Pipe Installation

Install threaded pipe nipple (1) to extend

past ﬁnished wall. Apply Teﬂon

®

tape to

threads on pipe nipple and screw on

tub spout.

Copper Sweat Installation

Remo

ve O-ring (1) from adapter (2). Solder

adapter to tube taking care to keep solder

away from O-ring groove. CAUTION: NO

SOLDER PERMITTED ON OUTSIDE

DIAMETER OF AD

APTER ADJACENT

TO O-RING GROOVE. Cut off tube (3) and

replace O-ring on groove of brass adapter.

Thread tub/spout onto adapter, taking care

not to damage O-ring, and hand tighten until

spout is ﬁrmly against ﬁnished wall and all

slack is taken up behind wall.

2

1

2

3

C.

D.

A.

B.

Slide O-ring (1) over cartridge and the

bonnet nut (2). The O-ring, which acts as

a spacer to steady the sleeve, should rest

behind the bonnet nut.

Slide the sleeve (1) over the cartridge,

body and O-ring. Ensure sleeve is properly

positioned over the front of cartridge.

Secure the escutcheon (1) and

bac

kplate (2) (if your model has one) to the

bracket (3) with the 2 screws provided (4).

Do not overtighten escutcheon screws.

Install volume control handle (1) with lever

to the right, then turn to the on position.

DO NOT SECURE WITH SCREW.

17 Series Installation

3

Trim Installation

1

2

1

2

3

4

1

9

4

Installation and Adjustment of the Rotational Limit Stop

C.

A.

B.

Place the temperature control knob (1)

on volume handle and rotate to the mixed

position (if required). DO NOT SECURE

WITH SCREW. Turn on water supplies;

let the water run until both hot and cold

w

ater is as hot/cold as possible. Place

thermometer in a plastic tumbler, and hold

the tumbler in the water stream. Record the

temperature reading.

If the water temperature is above 120°F,

remo

ve the temperature control knob (1)

and rotate the limit stop (2) clockwise one

tooth for every 4°F - 6°F (approximate)

change in temperature. If water temperature

is cooler than desired, rotate the limit stop

counterclockwise.

IMPORTANT: The ﬁrst position of the

Rotational Limit Stop (the Limiter) is that

position that restricts the rotation of the

stem the most and is at the maximum

clockwise setting. According to industry

standards, the maximum allowable

temperature of the water exiting from the

valve is 120

o

F. This temperature may vary

in your local area. The Rotational Limit Stop

may need to be readjusted if the inlet water

temperature changes. For instance, during

the winter, the cold water temperature is

colder than it is during the summer which

could result in varying outlet temperatures.

Typical temperature for a comfortable bath

or shower is between 90

o

–110

o

F.

Secure temperature control knob (1) with

screw (2) and snap control cover (3) onto

knob. NOTE: Secure screw until handle

w

obble is reduced, DO NOT FULLY

TIGHTEN. Overtightening will result in

difﬁculty to operate temperature control

knob. Screw is self locking.

17 Series Installation

1

2

1

3

10

Hotter

Colder

B.

1

4

2

3

17T Series Installation

1

Cartridge Installation

A.

Turn off water supplies. Remove

cover (1), bonnet nut (2) and test cap (3)

from the body

. If this is not a thin wall

mounting, the entire plasterguard (4)

may be removed. If screen (5) is in place,

remove before installing cartridge.

1

2

3

11

4

Rotate the cartridge (1) so the word

“UP” (2) appears on the top. Insert

car

tridge into valve body as shown. Make

sure the cartridge tubes and O-rings (3)

are properly seated in holes at the base of

the body. Ensure the keys on the body are

fully engaged with the slots in the body (4).

For back to back or reverse installations

(hot on right and cold on left): Rotate

cartridge (1) so the word “UP” (2) appears

o

n the bottom. Install the cartridge making

sure that the keys are fully engaged with the

s

lot in the brass body (see step B). Slide

bonnet nut (3) over the cartridge and thread

onto the body. Hand tighten securely.

Back to back Installation

Normal Installation

(changes not required)

Reverse

Installation

Cold

Hot

1

3

2

C.

Slide bonnet nut (1) over the cartridge

and thread onto the body. Hand tighten

securely.

1

5

17T Series Installation

12

2

3

2

1

4

FOR SHOWERHEAD INSTALLATION:

Connect top outlet (1) to shower arm (2)

with proper ﬁttings. To prevent damage

to ﬁnish on shower arm, insert wall end

of shower arm into shower ﬂange (3)

before screwing arm into riser connection.

Thread showerhead (4) onto shower

arm. Apply Teﬂon

®

tape to pipe threads on

both ends. Do not overtighten

showerhead.

Slip-On Installation

The copper tube (1) m

ust be 1/2” nominal

copper. Important: If it is necessary to cut

the copper tube, the end must be cham-

fered free of burrs to prevent cutting or

nicking O-ring inside the spout. Slide spout

over copper tube ﬂush with the ﬁnished tub

or wall surface. Tighten set screw (2), but

do not overtighten.

1

FOR TUB SPOUT INSTALLATION:

Refer to the installation instructions supplied with your spout. Do not connect deck mount

spouts to in-wall valves. Do not use hand showers connected in lieu of a tub spout to a

tub/shower valve. Do not use PEX tubing for tub spout drop.

B-1

B-2

B-3

Iron Pipe Installation

Install threaded pipe nipple (1) to extend

past ﬁnished wall. Apply Teﬂon

®

tape to

threads on pipe nipple and screw on

tub spout.

Copper Sweat Installation

Remo

ve O-ring (1) from adapter (2). Solder

adapter to tube taking care to keep solder

away from O-ring groove. CAUTION: NO

SOLDER PERMITTED ON OUTSIDE

DIAMETER OF AD

APTER ADJACENT

TO O-RING GROOVE. Cut off tube (3) and

replace O-ring on groove of brass adapter.

Thread tub/spout onto adapter, taking care

not to damage O-ring, and hand tighten

until spout is ﬁr

mly against ﬁnished wall

and all slac

k is taken up behind wall.

2

1

2

3

Showerhead and Tub Spout Installation

A.

C.

D.

A.

B.

Slide O-ring (1) over cartridge and the

bonnet nut (2). The O-ring, which acts as

a spacer to steady the sleeve, should rest

behind the bonnet nut.

Slide the sleeve (1) over the cartridge,

body and O-ring. Ensure sleeve is properly

positioned over the front of cartridge.

Secure the escutcheon (1) to the bracket

(2) with the 2 screws provided (3).

Do not overtighten escutcheon screws.

Install volume control handle (1) with

le

ver to the right. DO NOT SECURE

WITH SCREW.

3

Valve Trim Installation

1

2

1

2

1

3

17T Series Installation

13

Cleaning and Care

4

Installation and Adjustment of the Temperature Knob

Failure to do so may cause injury.

17T Series Installation

14

Adjust temperature limit stop! Turn on

water supplies; let the water run at both

full hot and full cold to ensure the water is

running as hot/cold as possible. Place a

thermometer in a plastic tumbler, and hold

the tumbler in the water stream. Place the

temperature knob (1) onto the splines (2),

then rotate the temperature knob until

you achieve your maximum desired

temperature from the outlet (not more

than 120° or the lower temperature

mandated by your local plumbing code).

Remove the temperature knob and replace

onto the splines (2), making sure that the

temper

ature knob limit stop (3) hits against

the volume handle limit stop (4) as shown.

Secure volume handle with set screw (5).

Secure the temperature knob using screw

(6) and place cap (7) on knob.

1

3

2

1

4

3

6

5

7

4

Care should be given to the cleaning

of this product. Although its ﬁnish is

extremely durable, it can be damaged by

harsh abrasives or polish. To clean, simply

wipe gently with a damp cloth and blot dry

with a soft towel.

Warning: Scrubbing Bubbles

®

Bathroom

Cleaner and Lysol

®

Basin Tub and Tile

Cleaner must not be used on the clear knob

handles and le

vers. Use of these cleaners

can result in cracked or severely damaged

handles. If overspray gets onto the handles,

immediately wipe them dry with a soft

cotton cloth

Cannot receive more than a trickle of water:

Both hot and cold supply lines must be pressurized.

If only one side is pressurized, the pressure balance

system will not allow adequate ﬂow of water.

Volume control handle rotates 360

degrees or is not positioned correctly per

escutcheon, (sleeve is also loose). The keys of

the cartridge have not been properly placed in the

keyways in the brass body or keys on cartridge

have been sheared off due to improper installation.

BE SURE TO CORRECT THIS

SITU

ATION IMMEDIATELY.

Cannot receive enough hot water:

See step 3 and/or chec

k water heater temperature.

Faucet leaks from tub spout/showerhead:

SHUT OFF WATER SUPPLIES. Replace Adapter

Assembly –Repair Kit RP46073.

If leak persists–

SHUT OFF

WATER SUPPLIES

Replace cartridge assembly–RP46463.

Unable to maintain constant water temperature:

SHUT OFF WATER SUPPLIES. Remove cartridge

assembly, shake cartridge side to side. Spool

should rattle in sleeve. If rattle cannot be heard,

spool may be stuck. Spool may be freed up by

rapping cartridge briskly sideways into the palm

of your hand. If spool cannot be freed, replace

cartridge assembly–RP46463.

NOTE: If the water in your area has lime, rust,

sand, or other contaminants in it, your pressure

balance valve will require periodic inspection.

The frequency of the inspection will depend on

the amount of contaminants in the w

ater. To

inspect cartridge, remove it from the body and

shake it rigorously. If there is a rattling sound,

the unit is functional and can be reinstalled in its

pre

vious position. If there is no rattle, replace the

cartridge with RP46463.

17 Series Maintenance

Faucet leaks from tub spout/showerhead:

SHUT OFF WATER SUPPLIES.

Replace seats and springs–Repair

Kit RP4993. Check condition of lower O-rings and

replace if necessary RP14414. See Helpful Hints 1,

2, & 3.

If leak per

sists:

SHUT OFF WATER SUPPLIES.

Replace cap assembly RP46070 or valve cartridge

RP46074.

See Helpful Hints 1, 2, 3 & 5.

Unab

le to maintain constant

water temperature:

Replace housing assemb

ly with RP46071 or follow

instructions in Helpful Hints 1, 2, 4 & 5.

Helpful Hints:

1.

Before removing valve cartridge assembly for any

maintenance, be sure to note the position of the

rotational limit stop on the cap. The valve cartridge

assembly must always be put back in the same

position. BE SAFE! After you have ﬁnished the

installation, turn on valve to make sure COLD

WATER FLOWS FIRST.

2. To remove valve cartridge from body, shut off

water supplies and remove handle and bonnet nut.

Do not pry the valve cartridge out of the body with

a screwdriver. Place handle on stem and rotate

counterclockwise approximately 1/4 turn after the

stop has been contacted. Lift valve cartridge out

of body.

3. To remove seats and springs, remove valve

cartridge. Separate cap assembly from the

housing assembly by rotating the cap assembly

counterclockwise 90

o

(degrees). Separate cap

and housing assemblies. Remove seats and

springs and replace. Place the largest diameter

of the spring into the seat pocket ﬁrst and then

press the tapered end of the seal over the spring.

Reassemble valve cartridge and replace in body

following instructions given in 1 above.

4. If the water in your area has lime, rust, sand

or other contaminants in it, your pressure

balance valve will require periodic inspection.

The frequency of the inspection will depend

on the amount of contaminants in the w

ater. To

inspect valve cartridge remove it and follow the

steps in note 1 above. Turn the valve to the full

mix position and shake the cartridge vigorously.

If there is a rattling sound, the unit is functional

and can be reinstalled following instructions given

in note 1 above. If there is no rattle, replace the

housing assembly (RP46071).

5.

Push disc until fully seated. See page 5 for

more details.

13/14 Series Maintenance

15

17T Series Maintenance

Faucet leaks from showerhead or tub spout:

SHUT OFF WATER SUPPLIES. Replace Cartridge

Assembly –Repair Kit RP47201.

16

MultiChoice™ 13/14

Grey

Off White

Longer

Lo

wer Housing

Order RP46074 to

Replace Cartridge.

Old

Monitor

®

1300/1400

White

Blue

or

Off

White

Shorter Lower Housing

Order RP19804 to

Replace Cartridge.

White

Blue

Shorter Lower Housing

Order RP19804 to

Replace Cartridge.

New

Monitor

®

1300/1400

17

Grey Upper Cap

Shorter Tab

V Notch

Adapter

Order RP46463 to

Replace Car

tridge.

1700

White Upper Cap

Longer Tab

Square Notch

Order RP32104 to

Replace Car

tridge.

17T

Brass

Black

NA

Will Not Fit

Order RP47201 to

Replace Car

tridge.

Cartridge Summary Reference Sheet

Units shipped in March

2006 and after.

Replacement cartridges

shipped in July 2006

and after.

Units shipped before

Mar

ch 2006.

NA

Instrucciones para la

Instalación del Accesorio

para Válvulas MultiChoice

™

Manual para los

Propietarios

13, 14, 17 y 17T

Series

Escriba aquí el número del modelo comprado.

U.S. Patents: 4,043,359, 3,786,995, 4,562,960,

4,593,430, 4,089,347, 4,218,785, 4,696,322,

4,765,365. More patents are pending.

ASME A112.18.1 / CSA B125.1

ASSE 1016

®

U

P

C

ESTA VÁLVULA CUMPLE O EXCEDE LAS

SIGUIENTES NORMAS:

ASME A112.18 1 / CSA B125.1 y ASSE 1016.

ADVERTENCIA: El instalador debe apostar

este systema/divisa para garantizar temperatura

maximo y seguro. Cualqueir cambio en el ajuste

puede subir la temperatura del agua de descarga

sobre el límite considerado seguro y puede

resultar en quemaduras de agua caliente.

AVISO PARA EL INSTALADOR: PRECAUCIÓN

– Como instalador de esta válvula, es su

responsabilidad de INSTALAR Y AJUSTAR

apropiadamente esta válvula como se describe

en las instrucciones, por lo tanto, debe haber

una persona para hacer los ajustes necesarios

del Tope del Límite Rotacional y del pomo

para la temperatura en el momento que se

haga la instalación y pueda necesitar ajustes

adicionales por los cambios estacionales

de la temperatura del agua. USTED DEBE

informarle al dueño/usuario sobre este

requisito siguiendo las instrucciones. Si usted

o el dueño/usuario no están seguros como

hacer estos ajustes apropiadamente, por favor

reﬁérase al Página 5 (series 13 / 14), Página 10

(serie 17) o Página 14 (serie 17T) y si todavía no

está seguro, llámenos al 1-800-345-DELTA.

Después de hacer la instalación y el ajuste,

usted puede agregarle a la etiqueta de aviso

proporcionada, su nombre, el nombre de la

compañía y la fecha cuando ajustó el Tope del

Límite Rotacional y el pomo para la temperatura y

aplicar o ﬁjar la etiqueta al dorso de la puerta del

gabinete más cercano y la etiqueta de aviso al

calentador de agua. Deje la Hoja de Instrucciones

para referencia del dueño/usuario.

ADVERTENCIA: Esta válvula de presión

balanceada y termostática está diseñada

para minimizar los ef

ectos de los cambios

de temperatura de agua por causa de los

cambios de presión en el agua de entrada,

comúnmente causados por lavadoras de

platos, lavadoras de ropa, inodoros, y otros

aparatos por el estilo. Puede no proporcionar

protección de quemaduras de agua caliente

cuando hay alguna falla de otros aparatos

para el control de temperatura en otro

sitio en el sistema de plomería. También

no proporcionará protección si el tope del

límite rotacional y el pomo para el ajuste de

la temperatura no está apropiadamente ﬁjo

o si cambia la temperatura del agua caliente

después de hacer los ajustes o si los cambios

del agua de entrada son por los cambios

estacionales.

ADVERTENCIA: No instale un aparato de corte

o cierre en cualquiera de las tomas de esta

válvula. Cuando este tipo de aparato cierra el

ﬂujo de agua, puede hacer fallar la habilidad

de la válvula de balancear las presiones del

agua caliente y fría.

Contenido:

Garantías ........................................................................... Página 2

Instrucciones de Instalación para la Series 13 / 14............. Páginas 3 -6

Instrucciones de Instalación para la Serie 17...................... Páginas 7-10

Instrucciones de Instalación para la Serie 17T ................... Páginas 11-14

Mantenimiento .................................................................... Páginas 14-15

Hoja resumen de referencia para el cartucho .................... Página 16

Piezas de Repuesto ............................................................Páginas 17-33

1

Usted puede necesitar

T

E

F

L

O

N

3/7/0748312 Rev. C

Todas las piezas y acabados de la llave Delta

®

están garantizados al consumidor comprador

original, de estar libres de defectos de material

y fabricación, por el tiempo que el consumidor

comprador original sea dueño de su casa. Delta

Faucet Company recomienda que use un

plomero profesional para todas las instalaciones

y zreparaciones.

Delta

reemplazará, LIBRE DE CARGO, durante

el período de garantía, cualquier pieza o

acabado que pruebe tener defectos de material

y/o fabricación bajo instalación normal, uso y

servicio. Piezas de repuesto pueden ser

obtenidas llamando al 1-800-345-DELTA (en los

Estados Unidos y Canada) o escribiendo a:

En los Estados Unidos:

Delta

Faucet Company

Product Service

55 E. 111th Street

Indianapolis, IN 46280

En Canada:

Delta

Faucet Canada

Technical Service Centre

420 Burbrook Place

London, ON N6A 4L6

Esta garantía es extensiva en lo que cubre el

reemplazamiento de todas las piezas

def

ectuosas y hasta el acabado, pero éstas

son las únicas dos cosas que están cubiertas.

CARGOS DE LABOR Y/O DAÑOS INCURRIDOS

EN LA INSTALACIÓN, REPARACIÓN, O

REEMPLAZAMIENTO COMO TAMBIÉN

GarantÍa Limitada De Por Vida de la Llave y su Acabado

CUALQUIER OTRO TIPO DE PÉRDIDA O

DAÑOS ESTÁN EXCLUÍDOS. Prueba de

compra (recibo original de venta) del comprador

consumidor original debe de ser disponible a

Delta para todos los reclamos. ESTA ES LA

GARANTÍA EXCLUSIVA DE DELTA FAUCET

COMPANY, QUE NO HACE CUALQUIER

OTRA GARANTÍA DE CUALQUIER TIPO,

INCLUYENDO LA GARANTÍA IMPLÍCITA DE

COMERCIALIZACIÓN.

Esta garantía excluye todo uso industrial,

comercial

y de negocio, a cuyos compradores

se les da una garantía limitada extendida de

cinco años desde la fecha de compra, con todos

los otros términos de esta garantía aplicados,

excepto el de duración de ésta. Esta garantía

es aplicable a las llaves de Delta

®

fabricadas

después de Enero 1, 1995.

Algunos estados/provincias no permiten la

e

xclusión o limitación de daños incidentales o

consecuentes, de manera que la limitación o

exclusión arriba escrita puede no aplicarle a

usted. Cualquier daño a esta llave, resultado del

mal uso, abuso, o descuido, o cualquier otro uso

de piezas de repuesto que no sean genuinas de

Delta

®

ANULARÁN LA GARANTÍA.

Esta garantía le da derechos legales específicos,

y usted puede, también tener otros derechos que

varían de estado/provincia a estado/provincia.

Es

aplicable sólo a las llaves Delta

®

instaladas

en los Estados Unidos de America, Canada

y Mexico.

Todas las piezas de la llave Delta HDF están

garantizadas al dueño original de estar libres de

defectos en materiales y en la mano de obra por

un período de cinco (5) años. Esta garantía se

hace al dueño original y será efectiva el día de la

compra como se ve en el recibo de compra.

Delta reemplazará, LIBRE DE CARGO, durante

el período de la garantía, cualquier pieza que

resulte defectuosa en materiales y/o en la mano

de obra bajo instalación, uso y servicio

normal. Las piezas de repuesto pueden ser

obtenidas de su comerciante o distribuidor local

que se encuentran en la guía telefónica o si

usted devuelve la pieza con el recibo de compra

a nuestra fabrica, Y LOS CARGOS DE

TRANSPORTE PAGADOS CON ANTELACION,

a la dirección dada. ESTA GARANTIA ES LA

UNICA GARANTIA EXPRESA DE DELTA.

CUALQUIER RECLAMO HECHO BAJO ESTA

GARANTIA TIENE QUE SER HECHO

DURANTE EL PERIODO DE CINCO AÑOS A

Q

UE SE REFIERE ARRIBA. CUALQUIER

GARANTIA IMPLICITA, INCLUYENDO LA

GARANTIA IMPLICITA DE

COMERCIALIZACION O CONVENIENCIA

PARA UN PROPOSITO PARTICULAR, SON

LIMITADOS EN DURACION A LA DURACION

DE ESTA GARANTIA. LOS CARGOS PARA LA

MANO DE OBRA Y/O DAÑOS INCURRIDOS EN

LA INSTALACION, REPARACION O

REEMPLAZO, ASI COMO LOS DAÑOS

INCIDENTALES O CONSECUENTES

CONECTADOS CON ELLOS SON EXCLUIDOS

Y NO SERAN PAGADOS POR DELTA.

Algunos estados no permiten limitaciones al

tiempo que dura la garantía implícita, o la

exclusión o limitación de los daños incidentales o

consecuentes, así que la limitación o exclusión

expresada arriba puede no ser aplicable a usted.

Esta garantía le da a usted derechos legales

especíﬁcos y usted puede también tener otros

derechos que varían de estado a estado.

Esta garantía es nula por cualquier daño a esta

llave que sea el resultado del mal uso, abuso,

negligencia, accidente, instalación impropia,

cualquier uso en violación de las instrucciones

suministradas por nosotros o cualquier uso de

piezas de repuesto que no sean piezas

gen

uinas Delta.

Garantia Limitada de Delta HDF

2

La page est en cours de chargement...

Delta Faucet T14278-LHP Guide d'installation

Delta Faucet T14278-LHP Guide d'installation

dans d''autres langues

Documents connexes

Autres documents