Simplicity 040410-00 Manuel utilisateur

Marque: Simplicity

Modèle: 040410-00

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Ce manuel convient également à

Installation & Operator’s Manual

Power

Management

System

Not for

Reproduction

2 BRIGGSandSTRATTON.COM

Briggs & Stratton Power Products Group, LLC

P.O. Box 702

Milwaukee, WI 53201-0702

be reproduced or transmitted in any form without the express written

permission of Briggs & Stratton Power Products Group, LLC.

Thank you for your purchase of this Briggs & Stratton® Power Management System. This product is designed for use with

specific home standby generators and may not function with generators produced by other manufacturers. Seek a qualified

electrical professional to determine applicability of this equipment to generators manufactured by others. When operated

and maintained according to the instructions in this manual, your power management system will provide many years of

dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with this system and how to

avoid them. We have made every effort to provide for a safe, streamlined and cost-effective installation. As each installation

is unique, it is impossible to know of and advise of all conceivable procedures and methods by which installation might be

achieved. We do not know all possible hazards and/or the results of each possible method or procedure. It is important that

you read and understand these instructions thoroughly before attempting to install or operate this equipment. Save these

original instructions for future reference.

This power management system requires professional installation before use. Refer to the Installation section of this

manual for instructions on installation procedures. Only licensed electrical contractors should install power management

systems. Installations must strictly comply with all applicable federal, state and local codes, standards and regulations. The

installer should follow the instructions completely.

Where to Find Us

You never have to look far to find Briggs & Stratton support and service for your system. Consult your Yellow Pages.

There are many authorized service dealers who provide quality service. You can also contact Technical Service by phone at

(800) 743‑4115 between 8:00 AM and 5:00 PM CT, or on the Internet at BRIGGSandSTRATTON.COM.

For Future Reference

Please fill out the information below and keep with your receipt to assist in unit identification for future purchase issues.

Power Management System

Model Number

Revision

Serial Number

Date Purchased

Not for

Reproduction

Table of Contents

Important Safety Instructions........................4

Installation ....................................5

Owner Orientation ............................................5

Installing Dealer/Contractor Responsibilities .......................5

Mounting Guidelines ..........................................6

Power Wiring Interconnections ..................................7

System Setup................................................9

System Test .................................................9

Operation .................................... 10

Wiring Decal................................................11

Electrical Load Worksheet .....................................12

Maintenance .................................. 13

Troubleshooting................................ 14

Warranty..................................... 15

Product Specifications ........................... 16

Not for

Reproduction

4 BRIGGSandSTRATTON.COM

Save These Instructions

Important Safety Instructions

SAVE THESE INSTRUCTIONS - This manual contains

important instructions that should be followed during

installation and maintenance of the equipment.

Safety Symbols and Meanings

The safety alert symbol indicates a potential personal

injury hazard. A signal word (DANGER, WARNING, or

CAUTION) is used with the alert symbol to designate a

degree or level of hazard seriousness. A safety symbol

may be used to represent the type of hazard. The signal

word NOTICE is used to address practices not related to

personal injury.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE addresses practices not related to personal injury.

The manufacturer cannot possibly anticipate every possible

circumstance that might involve a hazard. The warnings in

this manual, and the tags and decals affixed to the unit are,

therefore, not all-inclusive. If you use a procedure, work

method or operating technique that the manufacturer does

not specifically recommend, you must satisfy yourself that

it is safe for you and others. You must also make sure that

the procedure, work method or operating technique that you

choose does not render the equipment unsafe.

Electrical Shock Read Manual

NOTICE Only qualified electricians should attempt

installation of this equipment, which must strictly comply

with applicable codes, standards and regulations.

WARNING Certain components in this product and

related accessories contain chemicals known to the State

of California to cause cancer, birth defects, or other

reproductive harm. Wash hands after handling.

WAR NING Low voltage wire cannot be installed in

same conduit as power voltage wiring.

Failure to follow above warning could cause personal •

injury, damage and/or malfunction of equipment.

WAR NING Failure to properly ground equipment can

result in electrocution.

Do not touch bare wires.•

Do not use equipment with worn, frayed, bare or •

otherwise damaged wiring.

Do not handle electrical cords while standing in water, •

while barefoot, or while hands or feet are wet.

If you must work around a unit while it is operating, stand •

on an insulated dry surface to reduce shock hazard.

Do not allow unqualified persons or children to operate or •

service equipment.

In case of an accident caused by electrical shock, •

immediately shut down all sources of electrical power

and contact local authorities. Avoid direct contact with

the victim.

NOTICE Improper treatment of equipment can damage it

and shorten its life.

Use equipment only for intended uses.•

If you have questions about intended use, ask dealer or •

contact Briggs & Stratton Power Products.

Do not expose equipment to excessive moisture, dust, •

dirt, or corrosive vapors.

Remain alert at all times while working on this equipment. •

Never work on the equipment when you are physically or

mentally fatigued.

If connected devices overheat, turn them off and turn off •

their circuit breaker/fuse.

WAR NING Equipment contains high voltage that can

cause personal injury or death.

Despite the safe design of the system, operating this •

equipment imprudently, neglecting its maintenance or

being careless can cause possible injury or death.

Not for

Reproduction

Installation

We sincerely appreciate your patronage. For this reason,

we have made significant effort to provide for a safe,

streamlined and cost-effective installation. Because each

installation is unique, it is impossible to know of and advise

the trade of all conceivable procedures and methods by

which installation might be achieved. Neither could we know

of possible hazards and/or the results of each method or

procedure. For these reasons,

Only current licensed electrical should attempt system

installations. Installations must strictly comply with all

applicable codes, industry standards and regulations.

Your equipment is supplied with this combined “Installation

and Operator’s Manual”. This is an important document and

should be retained by the owner after the installation has

been completed.

Every effort has been expended to make sure that the

information in this manual is both accurate and current.

However, the manufacturer reserves the right to change,

alter or otherwise improve the system at any time without

prior notice.

Home Owner Responsibilities

To help you make informed choices and communicate

effectively with your installation contractor(s),

Read and understand Owner Orientation before contracting

or starting your equipment installation.

To arrange for proper installation, contact the store at which

you purchased your equipment, your dealer, or your utility

power provider.

The equipment warranty is VOID unless the system is

installed by licensed electrical professionals.

Owner Orientation

The illustrations provided are for typical circumstances and

are meant to familiarize you with the installation options

available with your system.

Local codes, appearance, and distances are the factors that

must be considered when negotiating with an installation

professional. As the distance from the existing electrical

service increases, compensation in wiring materials must

be allowed for. This is necessary to comply with local codes

and overcome electrical voltage drops.

These factors will have a direct effect on the overall price

of your equipment installation.

NOTE: Your installer must check local codes AND obtain

permits before installing the system.

 • Readandfollowtheinstructionsgiveninthismanual.

 • Followaregularscheduleincaringforandusingyour

equipment, as specified in this manual.

Installing Dealer/Contractor Responsibilities

 • Readandobservethesafetyrules.

 • Readandfollowtheinstructionsgiveninthismanual.

 • Consultwithownertodetermineloadstobecontrolled

and their priorities.

NOTE: A worksheet for determining which loads are to be

transferred and their priorities is provided in Electrical Load

Worksheet, later in this manual.

 • Theinstallermayneedtoprovideappropriaterated

contactors based on loads to be controlled.

Equipment Description

The system is designed to control four priority loads and up

to two air conditioner loads that are being supplied by power

generated by the home standby system. This system goes

into a STANDBY mode and does not control any loads when

utility power is present.

The power management system consists of four 50 Amp,

2 HP, 2 pole relays; four control relays for central air

conditioning control wiring (maximum 1 Amp, 30VAC, two of

these relays are air conditioner lockout). The circuit boards

are housed in a NEMA 3R enclosure that is suitable for both

indoor and outdoor installations.

Relays A1 and A2 are configured with a 5 minute delay for

use with air conditioning control wiring. The 5 minute delay

will allow the air conditioner head pressure to bleed off,

thus reducing in-rush current. Connecting air conditioner

power wires directly to contactors L1, L2, L3 or L4 is not

recommended. Possible failures include tripping of branch

circuit breaker, generator shutting down and damage to air

conditioner. Please contact the air conditioner manufacturer

to make sure that their unit incorporates a 5 minute starting

delay before you connect AC power wires to contactors L1,

L2, L3 or L4.

Two current transformers monitor generator current at

the transfer switch to ensure that generator load does

not exceed a predetermined level. Should load exceed the

predetermined level, the system will shed loads to prevent

the generator from overloading. Loads are added sequentially

when sufficient power becomes available.

The control module incorporates a LED for each relay. The

LOAD1 LED is lit when relay 1 is NOT supplying power

to the load (contactor is OPEN). The same is true for the

other three relay’s. There is also a STATUS LED on the

control module that flashes when the generator is supplying

power to the system and indicates that the equipment is

functioning properly.

Not for

Reproduction

6 BRIGGSandSTRATTON.COM

Delivery Inspection

After opening the carton, carefully inspect the contents for

any damage that may have occurred during shipment.

IMPORTANT: If loss or damage is noted at time of delivery,

have the person(s) making delivery note all damage on the

freight bill and affix his signature under the consignor’s

memo of loss or damage. If loss or damage is noted after

delivery, contact the carrier for claim procedures. Missing or

damaged parts are not warranted.

Shipment Contents

 • Powermanagementsystem(1)

 • Installationandoperator’smanual(1)

 • Fuse(2)

 • Fuseholder(1)

 • Currenttransformer(2)

 • Decal(1)

 • Screw(4)

 • Compactterminalblock(4)

 • 1/4”singlefemalelug(4)

 • 1/4”singlemale,singlefemalelug(2)

To be supplied by installer:

 • Connectingwireandconduit

 • Variousspecialtytools/equipment

Mounting Guidelines

The system circuitry is enclosed in a NEMA Type 3R

enclosure suitable for indoor/outdoor use. Guidelines for

mounting the enclosure include:

 • Installenclosureonafirm,sturdysupportingstructure.

 • TheenclosuremustbeinstalledwithminimumNEMA

3R hardware for conduit connections.

 • Levelandplumbtheenclosure.Thiscanbedone

by placing washers between the enclosure and the

mounting surface.

NOTE: UL mandates that “Class 2 field wiring shall be

contained in the upper (terminal block) portion of the

enclosure. High voltage field wiring shall be routed in a

manner to maintain separation (of 6 inch) to Class 2 wiring

(including PCB board).”

 • Neverinstallthedevicewhereanycorrosivesubstance

might drip onto the enclosure.

 • Protectthedeviceatalltimesagainstexcessive

moisture, dust, dirt, lint, construction grit and

corrosive vapors.

A typical installation is depicted below. It is best if the

enclosure is mounted near the main distribution panel, either

inside or outside the building. Discuss layout suggestions/

changes with the owner before beginning system installation.

Main

distribution

panel

Transfer

switch

Hot

water

heater

Air

conditioner

Service

disconnect

Generator

Watt -

hourmeter

Branch circuits

Disconnect

switch

Power

management

system

Contactor

Not for

Reproduction

Power Wiring Interconnections

All wiring must be the proper size, properly supported

and protected by conduit. All wiring should be done

per applicable federal, state and local codes, standards

and regulations. Obey wire type and torque specifications

printed on the terminal blocks and neutral/ground connector.

Complete the following connections between the

transfer switch, the power management system and the

main distribution panel. Also see Wiring Decal, later in

this manual.

1. Set generator’s system switch to OFF position.

2. Set generator’s circuit breaker to OFF (open) position.

3. In main distribution panel, identify loads and their

priorities (using list developed with owner) that will be

‘managed’ by the system. An Electrical Load Worksheet

is provided.

4. In main distribution panel, turn selected load circuit

breakers to OFF position.

5. Connect “GND” lug to an approved ground.

NOTE: Assure grounding electrode conductor is connected

and bonded per applicable federal, state and local codes,

standards and regulations.

Existing fuse

holder

Optional

fuse holder

GROUND

To 50A MAX

general

purpose

loads

To current

transformers

To air conditioning control

wiring (A1 and A2).

A3 and A4 are lockouts

TEST

button

WAR NING Low voltage wire cannot be installed in

same conduit as power voltage wiring.

Failure to follow above warning could cause personal •

injury, damage and/or malfunction of equipment.

NOTICE Improper installation can cause damage to the

circuit boards and shorten their life. Installing circuit

boards in live circuits will damage the board and is not

covered by warranty. ALWAYS disconnect ALL sources of

power prior to servicing.

Remove all power prior to installing this equipment. •

Failure to do so could cause internal damage to the board

when making electrical connections.

Turn generator to • OFF position.

Turn off utility power to the standby generator and •

transfer switch.

WARNING Battery posts, terminals and related

accessories contain lead and lead compounds, chemicals

known to the State of California to cause cancer and

reproductive harm. Wash hands after handling.

Not for

Reproduction

8 BRIGGSandSTRATTON.COM

6. As an optional step, install supplied fuse holder in

automatic transfer switch enclosure. Shown here is a

typical install location. Clear all metal shavings!

NOTE: If not using optional fuse holder, please follow

wiring decal attached to enclosure (see Wiring Decal).

7. Attach supplied “GENERATOR 240VAC” decal in close

proximity to optional fuse holder, if used.

NOTE: To satisfy separation of circuit requirement, low

voltage (Class 2) wiring must enter the enclosure 2 inches

(5 cm) away from the top of the board transformer.

See System Setup.

8. If optional fuse holder is used, perform steps 9 and

10 and omit step 11. If optional fuse holder is NOT

used, omit steps 9 and 10 and continue with step 11.

9. Using installer supplied 300VAC or greater wire and

supplied 1/4” single male, single female lugs, connect

generator 240VAC from generator side of transfer

switch to optional fuse holder installed in step 6. The

transfer switch and fuse holders are supplied with

1/4” male spade connectors.

10. Using installer supplied 300VAC or greater wire and

supplied 1/4” single female lugs, connect opposite

end of the optional fuse holder installed in step 6 to

terminal block in power management system labeled

“240VAC GENERATOR”. Proceed to step 12.

11. Using installer supplied 300VAC or greater wire and

supplied 1/4” single male, single female lugs, connect

generator 240VAC from generator side of transfer

switch to terminal block in power management system

labeled “240VAC GENERATOR”.

12. Remove current transformers from current transformer

kit, cut two pole connector ends off of current

transformer leads and discard. Strip wires and place in

supplied compact terminal blocks.

13. Using installer supplied 300VAC or greater wire, run

wires from compact terminal blocks to control module

terminal block labeled “CT1” and “CT2”.

14. Using installer supplied 300VAC or greater wire,

connect C (Common) and NO (Normally Open)

terminals on terminal block J9 of control module

in transfer switch to control module terminal block

labeled “TS COM” (see Wiring Decal) in power

management system.

15. Wire air conditioning control wiring to control module

terminal block labeled “A1”, “A2”, “A3”, and “A4” in

power management system.

NOTE: A1 is for air conditioner 1. A2 is for air conditioner 2.

A3 and A4 are lockout’s during power outage.

16. For 120VAC selected loads, remove wire from selected

load circuit breaker.

17. Connect the selected load wire to terminal block in

enclosure labeled “LOAD1” for priority 1 load.

18. Using installer supplied 300VAC or greater wire,

connect selected load circuit breaker to terminal block

in enclosure labeled “LINE” for priority 1 load.

19. Repeat steps 16 through 18 for all other 120VAC

priorities using terminals “LOAD2” through “LOAD4”.

20. For 240VAC selected loads, remove both wires from

selected load circuit breaker.

21. Connect both wires from the selected load to terminal

block in enclosure labeled “LOAD1” for priority 1 load.

22. Using installer supplied 300VAC or greater wire,

connect selected load circuit breaker to terminal block

in enclosure labeled “LINE” for a priority 1 load.

23. Repeat steps 20 through 22 for all other 240VAC

priorities using terminals “LOAD2” through “LOAD4”.

24. Tighten all wire connections/fasteners to proper torque.

See label inside power management system for proper

torque values.

1/4” single male,

single female lug

1/4” single

female lug

Add

GENERATOR

240VAC

decal

Add

supplied

fuse holder

Interior of

automatic

transfer

switch

Not for

Reproduction

System Setup

You must perform the following before operating the system:

 • SettheSW2andSW3dipswitchesonthepower

management system control board to match the KW

rating of the home standby generator, as described in

Setting Dipswitches.

 • Inmaindistributionpanel,turnselectedloadcircuit

breakers to the ON position.

Setting Dipswitches

Dipswitches are used to adjust control board operation

based on generator capacity and fuel source. SW2 (“ONE”)

and SW3 (“TEN”) switches are set to correspond to total

system kW rating. Dipswitch SW2 has units of 1,000 watts;

Dipswitch SW3 has units of 10,000 watts.

IMPORTANT: Set only one switch to “On” position on

SW2 and SW3.

The “On” position for the dipswitches is the switch number

ON THE CONTROL BOARD, not on the switch. For example,

on a 27,000 watt generator, set SW3 dipswitch “20” to “On”

position. Set SW2 dipswitch “7” to “On” position. 20,000

plus 7000 equals 27,000 watts.

IMPORTANT: After installation of the system is complete,

turn on utility power to the home standby generator and

transfer switch. Wait one minute before turning generator

system switch to AUTO.

System Test

With the generator system switch in AUTO, turn the service

disconnect feeding the transfer switch contactor to the OFF

position. After a few minutes the generator will start and the

transfer switch will transfer to generator power.

Press the test button on the control module (labeled

“SW1 TEST”) in the power management system. As the

button is pressed, a relay will energize. Each time the

button is pressed, the previous relay that was energized will

de-energize and the next relay will energize. This sequence

continues until all relays have been tested. If the test

button has not been pressed for a period of 30 seconds,

the test sequence will halt and the system will revert to

automatic control.

To return to utility power, turn the service disconnect feeding

the transfer switch to the ON position.

NOTICE Use extreme caution when setting dipswitches or

damage to control board will result.

Use a pencil or small piece of plastic to set the dipswitch.•

NEVER use a screwdriver or any type of metal object to •

set dipswitches.

Air Conditioning

control wiring

TS COM

connections

CT1 & CT2

connections

SW3

dipswitch

STATUS

LED

LOAD

LED’s

TEST

SW1

Control

board

transformer

SW2

dipswitch

Not for

Reproduction

10 BRIGGSandSTRATTON.COM

Operation

When the home standby generator is providing power to the

transfer switch, the power management system is constantly

monitoring generator output power. The system monitors

both incoming generator lines and keeps the home standby

generator loaded to a predetermined SET POINT. When the

current transformers on any line start to see current reach

SET POINT, the system will start shedding loads based on

the lowest priority and work its way to the highest priority.

When monitored current drops below SET POINT, the

system will start to add loads based on the highest priority

first, followed by the second highest until the generator

reaches SET POINT or all priorities are back on line. The

equipment will operate this way (shedding or adding loads)

until the transfer switch transfers back to utility power.

The system waits 10 seconds between adding or shedding

each load to permit the system to stabilize. When relays

A1 and A2 are opened, the relays will stay opened for

a minimum of 5 minutes or until the load can be added

without putting the generator over SET POINT load. When

contactors Load1, Load2, Load3 and Load4 are opened, the

relays will stay opened for a minimum of 30 seconds or until

the load can be added without putting the generator over

SET POINT.

If a large load demand is seen, the system will shed all

loads in less than 1 second to prevent the generator from

overloading. Once the demand has stabilized, the system will

re-load the generator, as described above.

In descending order, the priorities for load management

are A1, Load 1, Load 2, Load 3, Load 4, A2 (A1 is highest

priority and A2 the lowest). A3 and A4 are lockout’s in

generator mode.

Enclosure Door Mechanism

 • Toopendoor,pressthespring-loaddoorlocktothe

right and pull down on the door.

 • Tocloseandlatchdoor,pushdoorclosedagainst

enclosure. While in this position, push door upwards.

This will cause spring-load door lock to engage and

latch door in place.

NOTE: Enclosure door MUST be closed and latched at all

times except when system is being serviced.

Not for

Reproduction

Wiring Decal

Not for

Reproduction

12 BRIGGSandSTRATTON.COM

Priority 120VAC Electrical Appliances Priority 240VAC Electrical Appliances

Window Air Conditioner 1 Central Air Conditioner 1

Window Air Conditioner 2 Central Air Conditioner 2

Window Air Conditioner 3 Range/Stove

Refrigerator 1 Dryer

Refrigerator 2 Well Pump

Freezer 1 Hot Tub

Freezer 2 Pool Heater

Microwave Water Heater

Bathroom Other:________________________

Auxiliary Heater Other:________________________

Home Theater System Other:________________________

Garage Heater

Sink Water Heater

Other:________________________

IMPORTANT: DO NOT connect furnace, sewage pump or sump pump to the power management system.

Electrical Load Worksheet

Not for

Reproduction

Maintenance

The equipment is designed to be maintenance free under

normal usage. However, inspection and maintenance checks

should be made on a regular basis. Maintenance will consist

mainly of keeping the enclosure clean.

Visual inspections should be done at least once a month.

Access to the enclosure must not be obstructed. Keep

3 feet (92 cm) clearance around the device. Check for

an accumulation of dirt, moisture and/or corrosion on

and around the enclosure, loose parts/hardware, cracks

and/or discoloration to insulation, and damaged or

discolored components.

Perform the system test at least once every three months (as

described in System Test) unless a power outage occurs and

the generator system has gone through automatic sequence

in those three months. Allow the system to run for at least

30 minutes.

Contact a licensed electrical professional to inspect and clean

the inside of the enclosure and other components of your

home generator system at least once a year.

When Calling for Assistance

You must have the Model Number and Serial Number from

the unit ID label at hand if it is necessary to contact a local

service center regarding service or repair of this unit. Obtain

this information from the unit ID label located on or inside

the enclosure.

To contact Briggs & Stratton call (800) 743‑4115, between

8:00 AM and 5:00 PM CT.

Not for

Reproduction

14 BRIGGSandSTRATTON.COM

Troubleshooting

Problem Cause Correction

Su pervised loads (air conditioner,

etc.) are not operating when

generator is supplying power

1. Load1 – Load4 contactors not

operating correctly.

2. Too much load on generator.

3. Current transformer not connected.

4. Broken current transformer.

5. Status LED stays lit constantly.

1. Contact an authorized service center.

2. Decrease load to generator.

3. Contact an authorized service center.

4. Contact an authorized service center.

5. Contact an authorized service center

No power to power management

system when generator is

running.

Blown fuse in transfer switch. Contact an authorized service center.

Not for

Reproduction

Warranty

ABOUT YOUR WARRANTY

We welcome warranty repair and apologize to you for being inconvenienced. Any Authorized Service Dealer may perform warranty repairs. Most warranty

repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. For example, warranty service would not apply if

equipment damage occurred because of misuse, lack of routine maintenance, shipping, handling, warehousing or improper installation. Similarly, the

warranty is void if the manufacturing date or the serial number on the equipment has been removed or the equipment has been altered or modified. During

the warranty period, the Authorized Service Dealer, at its option, will repair or replace any part that, upon examination, is found to be defective under normal

use and service. This warranty will not cover the following repairs and equipment:

• Normal Wear: Outdoor Power Equipment, like all mechanical devices, needs periodic parts and service to perform well. This warranty does not cover

repair when normal use has exhausted the life of a part or the equipment.

• Installation and Maintenance: This warranty does not apply to equipment or parts that have been subjected to improper or unauthorized

installation or alteration and modification, misuse, negligence, accident, overloading, improper maintenance, repair or storage so as, in our judgment,

to adversely affect its performance and reliability. This warranty also does not cover normal maintenance such as adjustments, cleaning and

fuse replacement.

• Other Exclusions: This warranty excludes wear items or damage or malfunctions resulting from accidents, abuse, modifications, alterations, or

improper servicing. Accessory parts are excluded from the product warranty. This warranty excludes failures due to acts of God and other force

majeure events beyond the manufacturers control. Also excluded is used, reconditioned, and demonstration equipment. 198180E, Rev. D, 12/1/2009

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

MILWAUKEE, WI, USA

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC POWER MANAGEMENT SYSTEM

OWNER WARRANTY POLICY

LIMITED WARRANTY

Briggs & Stratton Power Products Group, LLC will repair or replace, free of charge, any part(s) of the equipment that is defective in material or

workmanship or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This

warranty is effective for the time periods and subject to the conditions stated below. For warranty service, find the nearest Authorized Service Dealer in

our dealer locator map at BRIGGSandSTRATTON.COM.

THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW. ANY AND ALL IMPLIED WARRANTIES ARE

EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED TO THE EXTENT EXCLUSION IS PERMITTED BY LAW. Some

states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion or limitation

of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and you

may also have other rights which vary from state to state or country to country.

Effective November 1, 2009 replaces all undated Warranties and all Warranties dated before November 1, 2009

The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time stated in the

table above. “Consumer use” means personal residential household use by a retail consumer. “Commercial use” means all other uses, including use for

commercial, income producing or rental purposes. Once equipment has experienced commercial use, it shall thereafter be considered as commercial use for

purposes of this warranty. Equipment used for prime power in place of utility are not applicable to this warranty.

NO WARRANTY REGISTRATION IS NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON PRODUCTS. SAVE YOUR PROOF OF PURCHASE

RECEIPT. IF YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY SERVICE IS REQUESTED, THE MANUFACTURING

DATE OF THE PRODUCT WILL BE USED TO DETERMINE THE WARRANTY PERIOD.

3 years

None

Consumer Use

Commercial Use

WARRANTY PERIOD

Not for

Reproduction

16 BRIGGSandSTRATTON.COM

* This power management system is listed per UL (Underwriters Laboratories) 916 (energy management equipment).

Product Specifications

Rated* AC Voltage .........................240 Volts

Frequency ...................................60 Hz

Contactor Rating

(L1, L2, L3, L4) ................. 240 VAC, 50A, 2 HP

Relay Contacts Rating

(A1, A2, A3, A4) ..................30 VAC, 1A, Class 2

Dimensions.....Approximately 24” H X 14” W X 6.5” Deep

Weight ..............................33 lbs (15 kg).

Not for

Reproduction

Manual de instalación

y del operario

Gestor de

alimentación

Not for

Reproduction

2 BRIGGSandSTRATTON.COM

Briggs & Stratton Power Products Group, LLC.

P.O. Box 702

Milwaukee, WI 53201-0702

o transmisión de este material, sea cual sea la forma empleada para ello, sin el

permiso previo y por escrito de Briggs & Stratton Power Products Group, LLC.

Gracias por comprar este gestor de alimentación de Briggs & Stratton Power Products®. Este producto está diseñado para

utilizarse con generadores de reserva domésticos específicos y puede no funcionar con generadores producidos por otros

fabricantes. Recurra a un electricista profesional cualificado para determinar la aplicabilidad de este equipo en generadores

fabricados por terceros. Si se utiliza y mantiene de acuerdo con las instrucciones de este manual, su sistema de gestión de

energía le proporcionará muchos años de funcionamiento fiable.

Este manual contiene información de seguridad para que usted conozca los peligros y riesgos propios de este sistema y

cómo evitarlos. Se ha realizado el máximo esfuerzo para que la instalación resulte segura, sencilla y económica. Debido a que

cada instalación es única, es imposible conocer y recomendar todos los procedimientos y métodos posibles para efectuarla.

No conocemos todos los riesgos y/o resultados posibles de cada método o procedimiento existente. Es importante que lea

y comprenda perfectamente estas instrucciones antes de intentar instalar o utilizar este equipo. Guarde estas instrucciones

para futuras consultas.

Este sistema de gestión de energía requiere instalación profesional antes de utilizarse. Consulte las instrucciones sobre

los procedimientos de instalación en la sección Instalación del presente manual. Los sistemas de gestión de energía sólo

deben ser instalados por electricistas con licencia. Las instalaciones deben cumplir estrictamente la totalidad de los códigos,

estándares y regulaciones federales, estatales y locales vigentes. El instalador debe seguir las instrucciones detalladamente.

Ubicación

Nunca debe ir demasiado lejos para encontrar el soporte y servicio de Briggs & Stratton para su sistema. Consulte las

Páginas Amarillas. Existen múltiples distribuidores de servicio autorizados que ofrecen un servicio de calidad. También puede

comunicarse con el Servicio técnico por teléfono al (800) 743 4115 de 8:00 a. m. a 5:00 p. m. Hora del Centro, o a través de

Internet en BRIGGSandSTRATTON.COM.

Para futuras consultas

Llene la siguiente información y conserve su factura para facilitar la identificación de la unidad en caso de que surjan

problemas relacionados con la compra en el futuro.

Número de modelo

Revisión

Número de serie

Fecha de compra

Not for

Reproduction

Tabla de contenido

Instrucciones importantes de seguridad ................4

Instalación ....................................5

Orientación al propietario.......................................5

Responsabilidades del distribuidor/técnico instalador ................5

Directrices de montaje .........................................6

Interconexión de los cables de alimentación ........................7

Configuración del sistema ......................................9

Prueba del sistema............................................9

Funcionamiento................................ 10

Calcomanía del cableado ......................................11

Hoja de trabajo de cargas eléctricas .............................12

Mantenimiento ................................ 13

Resolución de problemas ......................... 14

Garantía . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Especificaciones del producto ...................... 16

Not for

Reproduction

4 BRIGGSandSTRATTON.COM

Conserve estas instrucciones

Instrucciones importantes

de seguridad

GUARDE ESTAS INSTRUCCIONES - Este manual contiene

instrucciones importantes que se deben seguir durante la

instalación y el mantenimiento del equipo.

Símbolos sobre la seguridad y significados

El símbolo de alerta de seguridad indica un posible

riesgo para su integridad física. Se utiliza una palabra de

señalización (PELIGRO, ADVERTENCIA o ATENCIÓN) junto

con el símbolo de alerta para designar un grado o nivel

de gravedad de riesgo. Se puede utilizar un símbolo de

seguridad para representar el tipo de riesgo. La palabra de

señalización AVISO se utiliza para hacer referencia a una

práctica no relacionada con una lesión física.

PELIGRO indica un riesgo que, de no evitarse, provocará

la muerte o lesiones de gravedad.

ADVERTENCIA indica un riesgo que, de no evitarse,

podría provocar la muerte o lesiones de gravedad.

ATENCIÓN indica un riesgo que, de no evitarse, podría

provocar lesiones leves o moderadas.

AVISO hace referencia a una práctica no relacionada con una

lesión física.

El fabricante no puede prever todas las posibles

circunstancias que pueden implicar riesgos. Por lo tanto, las

advertencias que aparecen en este manual y las etiquetas

y calcomanías adheridas a la unidad no incluyen todas las

posibilidades. Si aplica un procedimiento, método de trabajo

o técnica de operación no recomendada específicamente

por el fabricante, debe estar seguro de que se trata de una

práctica segura para usted y para otras personas. También

debe asegurarse de que el procedimiento, método de trabajo

o técnica de operación que elija, no haga que el sistema de

gestión de energía eléctrica se torne inseguro.

Descarga eléctrica Lea el manual

AVISO La instalación de este equipo debe cumplir

estrictamente la totalidad de los códigos, estándares y

regulaciones vigentes, por lo que sólo debe ser llevada a

cabo por un electricista cualificado.

ADVERTENCIA Determinados componentes en

este producto y los accesorios relacionados contienen

sustancias químicas declaradas cancerígenas, causantes

de malformaciones, y otros defectos congénitos por

el Estado de California. Lávese las manos después de

manipular estos elementos.

ADV ERTENCIA Los cables de baja tensión no se

pueden instalar en el mismo conducto que los

cables de suministro de energía.

Si no se respeta esta indicación pueden producirse •

lesiones, daños y/o fallos de funcionamiento del equipo.

ADV ERTENCIA Una conexión a tierra defectuosa del

equipo puede provocar la electrocución.

No toque los cables pelados.•

No utilice el equipo con cables desgastados, •

deshilachados o deteriorados de cualquier otra forma.

No manipule los cables eléctricos si se encuentra en •

una zona húmeda, está descalzo o tiene las manos o los

pies mojados.

Si tiene que trabajar junto a una unidad en •

funcionamiento, manténgase en una superficie aislada y

seca para reducir el riesgo de descarga eléctrica.

No permita que personas no cualificadas o niños utilicen •

o reparen el equipo.

En caso de accidente provocado por una descarga •

eléctrica, desconecte inmediatamente todos los

suministros de energía eléctrica y póngase en contacto

con las autoridades locales. Evite el contacto directo con

la víctima.

ADV ERTENCIA El equipo contiene alta tensión que

puede provocar lesiones o la muerte.

A pesar de la seguridad del diseño del sistema, si éste se •

utiliza con imprudencia, ignorando su mantenimiento o

sin las debidas precauciones, se pueden producir lesiones

o incluso la muerte.

AVISO Un tratamiento inadecuado del equipo puede

estropearlo y acortar su vida útil.

Utilice el equipo sólo para los usos previstos.•

En caso de dudas sobre su uso, diríjase al distribuidor o a •

Briggs & Stratton Power Products.

No exponga el equipo a un exceso de humedad, polvo, •

suciedad o vapores corrosivos.

Manténgase alerta en todo momento cuando utilice este •

equipo. Nunca lo utilice ni manipule en condiciones de

fatiga física o mental.

Si se calientan excesivamente los dispositivos conectados, •

apáguelos y abra sus interruptores o quite sus fusibles.

Not for

Reproduction

La page charge ...

Simplicity 040410-00 Manuel utilisateur

Marque: Simplicity

Modèle: 040410-00

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Simplicity 040410-00 User manual
español: Simplicity 040410-00 Manual de usuario

Documents connexes

Autres documents

Briggs & Stratton 071013 Manuel utilisateur