Simplicity 040254-0 Manuel utilisateur

Catégorie
Groupes électrogènes
Taper
Manuel utilisateur
12000 / 15000 Watt
Residential Generator
System
Operator’s Manual
GEN12S, GEN15S, GEN20B & GEN25B
Manual No. 202114GS Rev. - (01/03/07)
Questions?
Help is just a moment away!
Call: Home Generator Helpline
(877) 369-9400 M-F 8-5 CT
Not for
Reproduction
Thank you for purchasing this quality-built Rheem / Ruud home standby generator. We are pleased that you’ve placed your
confidence in the Rheem or Ruud brand. When operated and maintained according to the instructions in this manual, your
Rheem / Ruud generator will provide many years of dependable service.
This manual contains safety information to make you aware of the hazards and risks associated with home standby
generators and how to avoid them. Because Rheem does not necessarily know all the applications this equipment could be
used for, it is important that you read and understand these instructions thoroughly before attempting to start or operate this
equipment. Save these instructions for future reference.
This home standby generator requires professional installation before use. Refer to the separate Installation manual for
instructions on safe installation procedures. Your installer should follow the instructions completely.
Where to Find Us
You never have to look far to find support and service for your home standby generator equipment. Consult your Yellow
Pages. There are many Rheem and Ruud authorized service dealers who provide quality service. You can also contact
Rheem/Ruud Customer Service by phone at (877) 369-9400.
Home Standby Generator
Model Number
Revision
Serial Number
Engine
Model Number
Type Number
Code Number
Date Purchased
Rheem Manufacturing Company
Randleman, NC 27317
(877) 369-9400
Copyright © 2007 Rheem Manufacturing Company. All rights
reserved. No part of this material may be reproduced or
transmitted in any form by any means without the express
written permission of Rheem Manufacturing Company.
Not for
Reproduction
1
Table of Contents
Important Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Owner Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Fuel Factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Generator Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Home Generator System Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Essential Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Shipment Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Before Initial Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Engine Oil. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Battery Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Gaseous Fuel System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Controls and Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
System Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Access Doors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Checking Automatic Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Servicing the System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Setting Exercise Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Fault Detection System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Changing Engine Oil. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Cleaning the Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
When Calling the Factory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Not for
Reproduction
2
Important Safety Rules
The safety alert symbol ( ) is used with a signal word
(DANGER, CAUTION, WARNING), a pictorial and/or a safety
message to alert you to hazards. DANGER indicates a hazard
which, if not avoided, will result in death or serious injury.
WARNING indicates a hazard which, if not avoided, could
result in death or serious injury. CAUTION indicates a hazard
which, if not avoided, might result in minor or moderate
injury. NOTICE indicates a situation that could result in
equipment damage. Follow safety message instructions to
avoid or reduce the risk of injury or death.
The manufacturer cannot possibly anticipate every possible
circumstance that might involve a hazard. The warnings in
this manual, and the tags and decals affixed to the unit are,
therefore, not all-inclusive. If you use a procedure, work
method or operating technique that the manufacturer does
not specifically recommend, you must satisfy yourself that it
is safe for you and others. You must also make sure that the
procedure, work method or operating technique that you
choose does not render the generator unsafe.
NOTE: Your generator is equipped with a spark arrester
muffler. The spark arrester must be maintained in effective
working order by the owner/operator. In the State of
California, a spark arrester is required by law (Section 4442
of the California Public Resources Code). Other states may
have similar laws. Federal laws apply on federal lands.
Hazard Symbols and Meanings
Save These Instructions
Explosion
Fire
Electrical Shock
Rotating Parts
Hot Surface
Toxic Fumes
Chemical BurnExplosive PressureAuto Start
Operate generator ONLY outdoors.
Install a battery operated carbon monoxide alarm near the
bedrooms.
Keep exhaust gas from entering a confined area through
windows, doors, ventilation intakes, or other openings.
WARNING
Running engine gives off carbon monoxide, an
odorless, colorless, poison gas.
Breathing carbon monoxide can cause headache,
fatigue, dizziness, vomiting, confusion, seizures,
nausea, fainting or death.
DO NOT dispose of battery in a fire.
Do not allow any open flame, spark, heat, or lit cigarette during
and for several minutes after charging a battery.
DO NOT open or mutilate the battery.
Wear protective goggles, rubber apron, and rubber gloves.
Remove watches, rings, or other metal objects.
Use tools with insulated handles.
WARNING
Storage batteries give off explosive hydrogen gas
during recharging.
Slightest spark will ignite hydrogen and cause
explosion.
Battery electrolyte fluid contains acid and is
extremely caustic.
Contact with battery contents will cause severe
chemical burns.
A battery presents a risk of electrical shock and
high short circuit current.
Not for
Reproduction
3
When using generator for backup power, notify utility company.
Do not touch bare wires or receptacles.
Do not use generator with electrical cords which are worn,
frayed, bare or otherwise damaged.
Do not handle generator or electrical cords while standing in
water, while barefoot, or while hands or feet are wet.
If you must work around a unit while it is operating, stand on an
insulated dry surface to reduce shock hazard.
Do not allow unqualified persons or children to operate or
service generator.
In case of an accident caused by electrical shock, immediately
shut down the source of electrical power and contact the local
authorities. Avoid direct contact with the victim.
Despite the safe design of the Home Generator System,
operating this equipment imprudently, neglecting its
maintenance or being careless can cause possible injury or
death.
Remain alert at all times while working on this equipment. Never
work on the equipment when you are physically or mentally
fatigued.
Before performing any maintenance on the generator, disconnect
the battery cable indicated by a NEGATIVE, NEG or (-) first.
When finished, reconnect that cable last.
After your Home Generator System is installed, the generator
may crank and start without warning any time there is a power
failure. To prevent possible injury, always set the generator’s
system switch to OFF, remove the service disconnect from the
disconnect box AND remove the 15 Amp fuse BEFORE working
on the equipment.
WARNING
Generator produces hazardous voltage.
Failure to properly ground generator can result in
electrocution.
Failure to isolate generator from power utility can
result in death or injury to electric utility workers
due to backfeed of electrical energy.
DO NOT touch hot parts and AVOID hot exhaust gases.
Allow equipment to cool before touching.
DO NOT install the generator closer than 5 feet (1.5m) from any
combustibles or structures with combustible walls having a fire
resistance rating of less than 1 hour.
Keep at least 3 ft. (91 cm) clearance on all sides of generator
including overhead.
Code of Federal Regulation (CFR) Title 36 Parks, Forests, and
Public Property require equipment powered by an internal
combustion engine to have a spark arrester, maintained in
effective working order, complying to USDA Forest service
standard 5100-1C or later revision. In the State of California a
spark arrester is required under section 4442 of the California
Public resources code. Other states may have similar laws.
WARNING
Contact with muffler area can result in serious
burns.
Exhaust heat/gases can ignite combustibles or
structures causing a fire.
Install the fuel supply system according to applicable fuel-gas
codes.
Before placing the Home Generator System into service, the fuel
system lines must be properly purged and leak tested.
After the generator is installed, you should inspect the fuel
system periodically.
NO leakage is permitted.
DO NOT operate engine if smell of fuel is present or other
explosive conditions exist.
DO NOT smoke around the generator. Wipe up any oil spills
immediately. Ensure that no combustible materials are left in the
generator compartment. Keep the area near the generator clean
and free of debris.
WARNING
Propane and Natural Gas are extremely flammable
and explosive.
Fire or explosion can cause severe burns or
death.
Not for
Reproduction
4
Use generator only for intended uses.
If you have questions about intended use, ask dealer or contact
Rheem.
Operate generator only on level surfaces.
Adequate, unobstructed flow of cooling and ventilating air is
critical to correct generator operation.
The Oil Fiil, Oil Drain and the Control Panel doors must be
installed whenever the unit is running.
DO NOT expose generator to excessive moisture, dust, dirt, or
corrosive vapors.
Despite the safe design of the Home Generator System, operating
this equipment imprudently, neglecting its maintenance or being
careless can cause possible injury or death.
Remain alert at all times while working on this equipment.
NEVER work on the equipment when you are physically or
mentally fatigued.
DO NOT start engine with air cleaner or air cleaner cover
removed.
DO NOT insert any objects through cooling slots.
DO NOT use the generator or any of its parts as a step. Stepping
on the unit can cause stress and break parts. This may result in
dangerous operating conditions from leaking exhaust gases, fuel
leakage, oil leakage, etc..
If connected devices overheat, turn them off and disconnect
them from generator.
Shut off generator if:
-electrical output is lost;
-equipment sparks, smokes, or emits flames;
-unit vibrates excessively.
NOTICE
Improper treatment of generator can damage it and shorten
its life.
See “Essential Circuits”.
Start generator and let engine stabilize before connecting
electrical loads.
NOTICE
Exceeding generators wattage/amperage capacity can
damage generator and/or electrical devices connected to it.
Observe that the 15 Amp fuse has been removed from the
control panel for shipping.
DO NOT install this fuse until all plumbing and wiring has been
completed and inspected.
CAUTION
Installing the 15A fuse could cause the engine to
start.
DO NOT tamper with governed speed. Generator supplies correct
rated frequency and voltage when running at governed speed.
DO NOT modify generator in any way.
CAUTION
Excessively high operating speeds increase risk of injury
and damage to generator.
Excessively low speeds impose a heavy load.
NEVER operate generator without protective housing or covers.
DO NOT wear loose clothing, jewelry or anything that may be
caught in the starter or other rotating parts.
Tie up long hair and remove jewelry.
WARNING
Starter and other rotating parts can entangle
hands, hair, clothing, or accessories.
Not for
Reproduction
5
Introduction
Thank you for your purchase of a Rheem / Ruud Home
Generator System (HGS). This product is intended for use as
an optional home standby system which provides an
alternate source of electric power and to serve loads such as
heating, refrigeration systems, and communication systems
that, when stopped during any power outage, could cause
discomfort, or the like. This product does not qualify for
emergency standby as defined by NFPA 70 (NEC).
Rheem has made every effort to provide for a safe,
streamlined and cost-effective installation. Because each
installation is unique, it is impossible to know of and advise
the trade of all conceivable procedures and methods by
which installation might be achieved. Neither could we know
of possible hazards and/or the results of each method or
procedure. For these reasons,
Only current licensed electrical and plumbing contractors
should attempt HGS installations. Installations must
strictly comply with all applicable codes, industry
standards and regulations.
Your Rheem / Ruud Home Generator System is supplied with
this “Operator’s Manual” and a separate “Installation
Manual”. These are important documents and should be
retained by the owner after the installation has been
completed.
For the Home Owner:
To help you make informed choices and communicate
effectively with your installation contractor(s),
Read and understand the
Owner Orientation Section of this manual
BEFORE
contracting or starting
your HGS installation.
To arrange for proper installation, contact your Rheem /
Ruud Home Generator System authorized dealer, a licensed
electrician or your utility power provider.
The HGS Warranty is VOID unless the system is installed
by licensed electrical and plumbing professionals.
The Emission Control System for this generator is warranted
for standards set by the U.S. Environmental Protection
Agency and by the California Air Resources Board (CARB).
Owner Orientation
This section provides Home Generator System owners with
the information necessary to achieve the most satisfactory
and cost effective installation possible.
Illustrations herein are for typical circumstances and are
meant to familiarize you with the installation options
available with your Home Generator System. A thorough
understanding of these options will provide fundamental
control over the cost of your installation, as well as ensure
your final satisfaction and security.
Federal and local codes, appearance, noise levels, fuel types,
and distances are the factors that must be considered when
negotiating with an installation professional. Remember that
as the distance from the existing electrical service and
gaseous fuel supply increases, equal compensations in
piping and wiring materials must be allowed for. This is
necessary to comply with local codes and overcome
electrical voltage drops and gaseous fuel pressure drops.
The factors mentioned above will have a direct affect on
the overall price of your Home Generator System
installation.
NOTE: Electrical permits for installing the Home Generator
System, building permits for installing gas lines, and permits
for noise allowances may be required. Your installer should
check your local codes AND obtain the permits before
installing the system.
Fuel Factors
An important consideration affecting the entire installation is
the type of fuel used by your Home Generator System. The
system was factory tested and adjusted using natural gas as
a fuel. Liquid propane (LP) may also be used as a fuel (see
the Installation Manual).
Although there are specific factors that are inherent to each
of these fuels, your location and the duration of possible
utility interruptions should guide your selection of fuel type.
For urban installations, Natural Gas (if available) should be
your fuel of choice. For remote installations, a Liquefied
Petroleum (LP) tank might better meet your needs.
For proper engine function, the following fuel guidelines are
recommended:
Use clean, dry fuel, free of moisture or any particulate
material. Using fuels outside the following
recommended values may cause performance
problems.
In engines set up to run on propane (LP) gas,
commercial grade HD5 propane with a minimum fuel
energy of 2500 BTUs/ft3 with maximum propylene
content of 5% and butane and heavier gas content of
2.5% and minimum propane content of 90%.
The Home Generator System is equipped with an automatic
safety gas “fuel shut-off” valve.
DO NOT operate the equipment if the “fuel shut-off” valve is
missing or inoperative.
WARNING
Propane and Natural Gas are extremely flammable
and explosive.
Fire or explosion can cause severe burns or
death.
Not for
Reproduction
6
Power Decrease at High Altitude or High Temperature
Air density is less at high altitudes, resulting in less available
engine power. Specifically, engine power will decrease 3.5%
for each 1,000 feet (300 meters) above sea level and 1% for
each 10° F (5.6°C) above 77°F (25°C). Make sure you and
your installer consider these factors when determining total
generator load.
Generator Location
The actual physical location of your HGS has a direct affect
on:
1. The amount of plumbing required to fuel your
generator.
2. The amount of wiring required to control and connect
your generator.
NOTE: Specific location guidelines are discussed in the
Installation Manual. Acquaint yourself with that information
and confer with your installer. Be sure to ask how your site
might affect installation costs and compliance with local
codes and standards.
Home Generator System Location
Before installing generator, consult with homeowner and
convey the following guidelines which may affect the desired
location.
Generator Clearances
Install generator outdoors in an area which will not
accumulate deadly exhaust gas. DO NOT install generator
where exhaust gas could accumulate and enter inside or be
drawn into a potentially occupied building. Ensure exhaust
gas is kept away from any windows, doors, ventilation
intakes or other openings that can allow exhaust gas to
collect in a confined area (Figure 1). Prevailing winds and air
currents should be taken into consideration when positioning
generator.
Figure 1 Home Generator System Location
General Location Guidelines
Install the unit outdoors ONLY.
Place the unit in a prepared location that is flat and has
provisions for water drainage.
Install the unit in a location where sump pump
discharge, rain gutter down spouts, roof run-off,
landscape irrigation, or water sprinklers will not flood
the unit or spray the enclosure and enter any air inlet
our outlet openings.
Install the unit where the location of any services such
as phone, electrical, fuel, air conditioning, irrigation,
including covered, concealed and underground services
will not be affected or obstructed.
Install the unit where air inlet and outlet openings will
not become obstructed by leaves, grass, snow, etc. If
prevailing winds will cause blowing or drifting, you may
need to construct a windbreak to protect the unit.
Install the generator as close as possible to the Transfer
Switch to reduce the length of wiring and conduit.
Install the generator as close as possible to the fuel
supply to reduce length of pipes.
Operate generator ONLY outdoors.
Install a battery operated carbon monoxide alarm near the
bedrooms.
Keep exhaust gas from entering a confined area through
windows, doors, ventilation intakes, or other openings.
WARNING
Running engine gives off carbon monoxide, an
odorless, colorless, poison gas.
Breathing carbon monoxide can cause headache,
fatigue, dizziness, vomiting, confusion, seizures,
nausea, fainting or death.
DO NOT install the generator closer than 5 feet (1.5m) from any
combustibles or structures with combustible walls having a fire
resistance rating of less than 1 hour.
Keep at least 3 ft. (91 cm) clearance on all sides of generator
including overhead.
WARNING
Exhaust heat/gases can ignite combustibles or
structures causing a fire.
Exhaust Port
Not for
Reproduction
7
IMPORTANT: Laws or local codes may regulate the distance
to the fuel supply.
The Home Generator System is shipped already attached to
its mounting pad. Unless mandated by local code, a concrete
slab is not required.
If mandated by local code, construct a concrete slab at least
3 inches thick and 6 inches longer and wider than the unit.
Attach unit to slab with 1/4” diameter (minimum) masonry
anchor bolts long enough to retain the unit.
Essential Circuits
As a Home Generator System owner, it is important that you
clearly identify the circuits in your building that are "essential"
to you.
It is important that your installer understand which circuits
you want to include as "Essential Circuits". Depending on the
power consumed by these circuits, most or all of them can
be switched to the Home Generator System for the duration
of normal power interruption.
The wattage reference guide shown in Figure 2 will assist you
with your decision-making process. It provides the wattage
used by many ordinary household devices. Use it as a guide
when selecting your essential circuits. Review this
information with your installer and ask about any technical
considerations that might affect the cost of your installation.
Figure 2 Wattage Reference Guide
*Allow three (3) times listed watts for starting device
Not for
Reproduction
8
Essential Circuit Selection
When selecting the essential circuits that will be switched to
“Standby Power,” it is important that the sum of the combined
circuit loads does not exceed the wattage/amperage capacity of
the generator. To help you with your selection of essential
circuits, please consider the following:
Add up the total wattage of all electrical devices to be
connected at one time. This total should NOT be greater
than the generator’s wattage capacity.
The rated wattage of lights can be taken from light
bulbs. The rated wattage of tools, appliances and
motors can usually be found on a data plate or decal
affixed to the device.
If the appliance, tool or motor nameplate does not list
wattage, multiply volts times the ampere rating to
determine watts (Volts x Amps = Watts).
Some electric motors (induction types) require about
three times more watts of power for starting than for
running. This surge lasts for only a few seconds. Be
sure you allow for this high starting wattage when
selecting electrical devices that will be energized by the
Home Generator System:
Figure the watts required to start the largest motor.
Add that to the total running watts of all other
connected loads.
This Rheem / Ruud Home Generator System complies with
the following “stationary standby power rating”:
The standby power rating is applicable for supplying
power for the duration of normal power interruption.
No sustained overload capability is available for this
rating.
This rating is applicable to installations served by a
reliable normal utility source. This rating is only
applicable to variable loads with an average load factor
of 80% of the standby rating. The standby rating is only
applicable for optional standby power where the
generator set serves as the backup to the normal utility
source.
Use the “Wattage Reference Guide” provided and mark those
circuits you consider “critical” or “essential”. Make sure you
and your installer consider the system’s altitude above sea
level and the ambient temperature range when determining
total generator load.
IMPORTANT: When using the 100 Amp or 200 Amp transfer
switch with the Home Generator System, you must turn off
any non essential loads. Failure to turn off non essential
loads could overload the generator causing it to shut down.
Some examples of non essential loads are:
Pool pump
Hot tub
Electric hot tub and/or pool heaters
Non-essential air conditioners
Electric hot water heaters
Electric range and/or oven
Arc welder
Non essential electric heaters
Assembly
Unpacking
Refer to the Installation Manual for detailed unpacking
instructions, if desired.
Delivery Inspection
After removing the carton, carefully inspect the Home
Generator System for any damage that may have occurred
during shipment.
IMPORTANT: If loss or damage is noted at time of delivery,
have the person(s) making delivery note all damage on the
freight bill and affix his signature under the consignor's
memo of loss or damage. If loss or damage is noted after
delivery, separate the damaged materials and contact the
carrier for claim procedures. Missing or damaged parts are
not warranted.
Not for
Reproduction
Shipment Contents
The Home Generator System is supplied with:
Home Generator System
Pre-attached mounting pad
One flexible fuel hook-up hose
Installation and start-up manual
Operator’s manual
Illustrated parts list manual
Installation checklist
Two access door keys
Four lifting hole plugs
Oil fill spout
One spare 15A fuse
2 Pole connector (for 240V from house)
10 Pole connector (for sensing and control wires)
Air intake engine cover
Alternator cover
Diagnostic LED kit (red LED/plate/screws (2))
Before Initial Start-Up
Engine Oil
This engine is shipped from the factory filled with the
recommended oil. Before starting the engine, check oil level
and ensure that engine is serviced as described in the engine
operator’s manual.
Oil Considerations
Your Home Generator System is equipped with an engine
that has been pre-run at the factory and does not require the
traditional “break-in” procedure.
The system is filled with synthetic oil (API SJ/CF 5W-30W).
This allows for system operation in the widest range of
temperature and climate conditions.
NOTE: The use of synthetic oil DOES NOT alter the required
oil change intervals described in the engine operator’s
manual.
Battery Connection
The Home Generator System is supplied with a 12 Volt DC
55 Amp-Hour, valve regulated battery. It is a sealed, lead-
acid rechargeable battery. It is installed in the unit and the
battery cables are connected at the factory. The generator’s
15 Amp fuse has been removed to prevent the unit from
starting during shipping.
NOTE: With the battery installed, all wiring to transfer switch
and Home Generator System completed, utility power
supplied to the Automatic Transfer Switch, and the unit in
AUTO mode, the battery receives a trickle charge while the
engine is not running. The trickle charger cannot be used to
recharge a battery that is completely discharged.
Gaseous Fuel System
Ensure that all fuel connections are tight, secure and
without leaks.
Ensure that all shutoff valves are OPEN and that
adequate pressure is available (see installation manual).
9
Refer to engine manual for oil fill information.
Damage to equipment resulting from failure to follow this
instruction will void warranty.
NOTICE
Any attempt to crank or start the engine before it has been
properly serviced with the recommended oil will result in
equipment failure.
DO NOT install this fuse until all plumbing and wiring has been
completed and inspected.
CAUTION
Installing the 15A fuse could cause the engine to
start.
DO NOT operate engine if smell of fuel is present or other
explosive conditions exist.
If you smell ‘raw’ gaseous fuel (natural or LP) near the unit,
immediately turn off the gas supply to the Home Generator
System.
Contact your gas utility or the system installer for assistance in
determining the source of the smell.
WARNING
Propane and Natural Gas are extremely flammable
and explosive.
Fire or explosion can cause severe burns or
death.
Not for
Reproduction
10
Controls and Features
Read this Operator’s Manual and safety rules before operating your generator.
Compare the illustrations with your generator to familiarize yourself with the locations of various controls and
adjustments. Save this manual for future reference.
15 Amp Fuse — Protects the DC control circuits.
Air Cleaner — Protects engine by filtering dust and debris
out of intake air.
Battery — 12 Volt DC, 55 Amp-Hour sealed battery provides
power to start the engine. Battery receives trickle charge
whenever generator is not running.
Control Panel — Used for various test, operation and
maintenance functions. See the next page.
Engine Label — Identifies engine model and type.
Exhaust Port — High-performance muffler lowers engine
noise to comply with most residential codes.
Oil Dip Stick — Used to check the engine oil level.
Oil Drain Hose — Provided to facilitate oil changing.
Oil Fill Cap — Remove to service the engine with
recommended oil.
Oil Filter — Filters engine oil to prolong system life.
Unit Data Decal (located on base) — Identifies unit by serial
number.
Air Cleaner
Oil Filter
Control Panel Door Opening
Oil Fill Door Opening
Unit Data Decal
Oil Drain Door Opening
Exhaust Port
Oil Dip Stick
Fuel Inlet
Control Panel
(see page 11)
Battery
Oil Drain Hose
Oil Fill Cap
15 Amp Fuse
Engine Label
Not for
Reproduction
11
15 Amp Fuse Protects the Home Generator System DC
control circuits. If the fuse has ‘blown’ (melted open) or was
removed, the engine cannot crank or start. Replace the fuse
using only an identical ATO 15A fuse.
Circuit Breaker Protects the system from shorts and
other over-current conditions. Must be ON to supply power
to the Automatic Transfer Switch.
Digital Display — Displays the total number of hours the
generator has been running and fault codes. Used to
schedule maintenance tasks and troubleshooting operational
problems with the Home Generator System. All fault
conditions are described in the section “Fault Detection
System”.
Manual Over-Ride Switch With system switch in AUTO
position, push the manual over-ride switch to start the
generator. To turn off the generator, push and hold the
manual over-ride switch again until engine stops.
Service Tool — For use by qualified service personnel ONLY.
Set Exercise Switch — Used to set the exercise cycle start
time and day-of-the-week. Exercise cycle only occurs in
AUTO mode.
System Switch — This two-position switch is the most
important control on the system and is used as follows:
•“AUTO” position is the normal operating position. If a
utility power outage is sensed, the system will start the
generator. When utility power is restored, it lets the
engine stabilize internal temperatures, shuts off the
generator, and waits for the next utility power outage.
•“OFF” position turns off running generator, prevents
unit from starting and resets any detected faults.
System Control Panel
Compare this Control Panel illustration with your generator to familiarize yourself with the location of these important controls:
Manual Over-Ride
Switch
Set Exercise
Switch
System Switch
Digital Display
15 Amp Fuse
Service Tool
Circuit
Breaker
Not for
Reproduction
12
Access Doors
The Home Generator System is equipped with an enclosure
that has three access doors (Figure 3). The doors are named
for a significant component located behind them. Starting
with the side that has the fuel connection and proceeding
clockwise, the doors are named:
Oil Fill door
Control Panel door
Oil Drain door
Each Home Generator System is equipped with two identical
keys. These keys fit the locks that secure the access doors.
To Open an Access Door:
1. Insert key into lock of access door you wish to open
and turn one quarter turn counterclockwise.
2. Grasp door’s handle and turn one quarter turn
counterclockwise to open. Remove key.
To Close an Access Door:
1. Close door and turn doors handle one quarter of a turn
clockwise.
2. Insert key into lock of access door and turn one quarter
turn clockwise. Remove key.
Oil Fill Door
Fuel Inlet
Exhaust
Port
Control Panel Door
Oil Drain Door
Exhaust Bulkhead
Figure 3 — Enclosure Access Doors
DO NOT touch hot parts and AVOID hot exhaust gases.
Allow equipment to cool before touching.
WARNING
Contact with muffler area can result in serious
burns.
Not for
Reproduction
13
Operation
To select automatic operation, do the following:
1. Set the service disconnect or main distribution panel
circuit breaker that sends utility voltage to the transfer
switch to ON.
2. Set the generator’s main circuit breaker to its ON
position.
3. Set the system switch to AUTO.
Checking Automatic Operation
To check the system for proper automatic operation, proceed
as follows:
1. Turn OFF the service disconnect or main distribution
panel circuit breaker sending power to the automatic
transfer switch.
The engine will crank and start when the utility voltage drops
out and the sensor has timed out. Let the system go through
its entire automatic operation sequence.
2. With the generator output supplying its loads, turn ON
the service disconnect or main distribution panel circuit
breaker that supplies utility power to the Automatic
Transfer Switch.
3. The automatic transfer switch will transfer loads back
to the utility power after 5 minute minimum run time
and utility is restored.
4. The generator will run for an additional one minute for
engine cool down, then shut down.
NOTE: If utility is restored and generator does not shut down
after 10 minutes, set system switch to OFF and contact your
installer or local service center.
This completes the test procedures for automatic operation.
The Home Generator System will now start automatically
when utility power is lost and will supply power to the
transfer switch.
Servicing the System
To service system:
1. Set the system switch to OFF.
2. Set the generator’s main circuit breaker to its OFF
position.
3. Utility voltage is present. Disconnect power before
servicing by removing the two 2 Amp fuses from the
transfer switch.
Setting Exercise Timer
The Home Generator System is equipped with an exercise
timer that will start and exercise the system once every
seven days. During this exercise period, the unit runs for
approximately 20 minutes and then shuts down. Electrical
load transfer DOES NOT occur during the exercise cycle
(unless an utility power outage occurs).
A switch on the control panel is labeled “Set Exercise” (see
page 11). The specific day and the specific time of day this
switch is pressed is programmed into the control board
memory. This date and time is then used to automatically
initiate the system exercise cycle. The LED on the control
panel will flash until the set exercise is set.
To perform the Set Exercise procedure:
1. Choose the day and time you want your Home
Generator System to exercise.
2. On that day and time, press and hold down the “Set
Exercise” switch for three seconds.
NOTE: The LED will flash until the switch is pressed for three
seconds, then the LED will illuminate for 5 seconds and turn
off.
For example, if you press the “Set Exercise” switch on
Sunday morning at 10:00 AM, the unit will run an exercise
cycle the following Sunday at 10:00 AM (+/- 1/2 hour).
NOTE: “Set Exercise” will only work if the unit is in the
Automatic mode and this exact procedure is followed. The
exerciser will need to be re-set if the 15 Amp fuse is
removed or changed, or if the 12 Volt DC battery is
disconnected.
If you want to change the day and time the unit exercises,
simply perform the “Set Exercise” procedure at the exact
weekday and time you want it to take place.
To prevent possible injury that might be caused by such sudden
starts, always set the system switch to OFF.
Remove the 15 Amp fuse before working on or around the
generator or transfer switch.
CAUTION
With the switch set to AUTO, the engine may
crank and start at any time without warning. Such
automatic starting normally occurs when utility
source voltage drops below a preset level or
during the normal exercise cycle.
Not for
Reproduction
Fault Detection System
The generator may have to run for long periods of time with
no operator present. For that reason, the system is equipped
with sensors that automatically shut down the generator in
the event of potentially damaging conditions, such as low oil
pressure, high oil temperature, over speed, and other
conditions.
The generator's control panel has a digital display to show
fault codes. An extra LED indicator is installed at a
convenient inside location. The LED will turn on and off in a
series of blinks if certain problems are detected in your HGS.
The blink pattern is repeated with a brief pause between each
series. The fault code as shown on the control panel, and the
number of blinks on the mounting plate, indicates the
detected fault and as follows:
Fault Codes / LED Flashes Fault Description
FC_1 / 1 Low battery voltage
FC_2 / 2 Low oil pressure
FC_3 / 3 Low voltage
FC_4 / 4 Engine fail to start
FC_5 / 5 Low frequency
FC_6 / 6 Engine overspeed
FC_7 / 7 Oil temperature high
FC_8 / 8 Transfer switch fault
Reset Fault Detection System
The operator must reset the fault detection system each time
it activates. To do so, place the system switch in the OFF
position for 5 seconds or more. Return the Home Generator
System to service after correcting the problem by placing the
system switch in the AUTO position.
A description of each fault and suggested remedies are as
follows:
No LED - Discharged Battery
This condition is caused by a completely discharged battery.
To remedy the problem, remove the 15 Amp fuse and
disconnect the battery from the generator. Take the battery to
a local battery store for analysis.
Replace the battery after it has been fully recharged,
connecting the NEGATIVE cable last. Install the 15 Amp fuse.
Low Battery Voltage
This fault is indicated by fault code FC_1 and one blink on
the LED indicator. This condition occurs if the generator
cannot start because the starting battery output power is
below that needed to crank the engine. Causes for this
problem may be a faulty battery or trickle charger circuit.
To remedy the problem, contact your local service center to
check the battery trickle charge output. Remove the 15 Amp
fuse and disconnect the battery from the generator. Take the
battery to a local battery store for analysis.
Replace the battery after it has been fully recharged,
connecting the NEGATIVE cable last. Install the 15 Amp fuse.
Low Oil Pressure
This fault is indicated by fault code FC_2 and two blinks on
the LED indicator. The unit is equipped with an oil pressure
switch (Figure 4) using normally closed contacts that are
held open by engine oil pressure during operation. Should oil
pressure drop below the 8 psi range, switch contacts close
and the engine is shut down.
To remedy the low oil pressure condition, add the
recommended oil to the FULL mark on the dipstick.
If low oil pressure condition still exists, engine will start,
then shut down after about 20 seconds and diagnostic LED
will flash. In this case, contact an authorized service facility.
14
Figure 4 Low Oil Pressure & High Temp. Switches
High
Temperature
Switch
Oil Drain
Fitting
Oil
Pressure
Switch
High
Temperature
Switch
Oil Drain
Fitting
Oil
Pressure
Switch
15kW
12kW
Not for
Reproduction
15
Low Voltage (Generator)
This fault is indicated by fault code FC_3 and three blinks on
the LED indicator. This condition is caused by a restriction in
the fuel flow, a broken or disconnected signal lead, a failed
alternator winding, the control panel circuit breaker is open,
or Home Generator System is overloaded.
To remedy the problem, contact your local service center.
Engine Fail To Start
This fault is indicated by fault code FC_4 and four blinks on
the LED indicator. This feature prevents the generator from
damaging itself if it continually attempts to start in spite of
another problem, such as no fuel supply. Each time the
system is directed to start, the unit will crank for
10 seconds, pause for 10 seconds, crank for 10 seconds,
pause for 10 seconds, and repeat. If the system does not
begin producing electricity after approximately 2 minutes,
the unit will stop cranking and the LED will blink.
Check to make sure the generator’s main circuit breaker is in
the ON (closed) position in order for the sensing leads to
verify that the unit is running.
The most likely cause of this problem is no fuel supply.
Check the inside and outside fuel shut off valves to ensure
they are fully open. Other causes could be failed spark
plug(s), failed engine ignition, or the engine air filter is
clogged. You may need to contact your installer for
assistance if you can’t remedy these problems.
Low Frequency
This fault is indicated by fault code FC_5 and five blinks on
the LED indicator. This feature protects devices connected to
the transfer switch by shutting the generator down if the
engine runs slower than the preset limit.
If the generator output frequency is below 55 Hz for
three seconds, the generator will shut down.
This condition is caused by a failed engine governor or by
excessive loads on the generator. To remedy the problem,
you may need to contact your installer or local service center
for assistance.
Engine Overspeed
This fault is indicated by fault code FC_6 and six blinks on
the LED indicator. This feature protects devices connected to
the transfer switch by shutting the generator down if the
engine happens to run faster than the preset limit. The
overspeed fault is detected as follows:
If the generator output frequency is 65-70 Hz, after
three seconds, the generator will shut down.
If the generator output frequency is greater than 70 Hz,
the generator will shut down instantly.
This condition is caused by a failed engine governor. To
remedy the problem, you should contact your installer or
local service center for assistance.
Oil Temperature High
This fault is indicated by fault code FC_7 and seven blinks on
the LED indicator. The contacts of the temperature switch
(Figure 4) are normally open. If the engine oil temperature
exceeds approximately 140°C (284°F), the fault is detected
and the engine shuts down.
Common causes for this condition include running the unit
with all access doors removed, obstructed air inlet or
exhaust port, low oil level, or debris in the engine cylinder
cooling fins.
To resolve the problem, remove any accumulated debris and
obstructions and let the engine cool down. Ensure that the
Oil Service door and/or the Control Panel door is installed
whenever the unit is running.
Transfer Switch Fault
This fault is indicated by fault code FC_8 and eight blinks on
the LED indicator (if transfer switch is equipped with fault
detection).
To remedy the problem, you should contact your installer or
local service center for assistance.
Not for
Reproduction
Maintenance
The generator warranty does not cover items that have been
subjected to operator abuse or neglect. To receive full value
from the warranty, the operator must maintain the system as
instructed in the engine operator’s manual.
All adjustments should be made at least once each season.
Follow the requirements in the engine operator’s manual.
Generator maintenance consists of keeping the unit clean.
Operate the unit in an environment where it will not be
exposed to excessive dust, dirt, moisture or any corrosive
vapors. Cooling air louvers on the enclosure must not
become clogged with snow, leaves, or any other foreign
material.
Check the cleanliness of the unit frequently and clean when
dust, dirt, oil, moisture or other foreign substances are
visible on its exterior/interior surface.
NOTE: DO NOT use direct spray from a garden hose to clean
generator. Water can enter the engine and generator and
cause problems.
Changing Engine Oil
Place the oil drain tube into an approved container.
Push in and rotate the oil drain fitting 1/4 turn
counterclockwise. Slowly pull outward until oil starts
draining (Figure 5). Do Not pull the oil drain fitting off
the engine.
When the oil has drained, push the oil drain fitting in
and rotate 1/4 turn clockwise until it locks in place.
Slide the oil drain tube up into the clamp on the
generator panel.
To fill your engine with oil:
Follow the synthetic oil grade recommendation and oil
fill instructions given in the engine operator’s manual.
Cleaning the Generator
Use a damp cloth to wipe exterior surfaces clean.
Use a soft, bristle brush to loosen caked on dirt, oil,
etc.
Use a vacuum cleaner to pick up loose dirt and debris.
Use low pressure air (not to exceed 25 psi) to blow
away dirt. Inspect cooling air slots and openings on the
generator. These openings must be kept clean and
unobstructed.
When Calling the Factory
You must have the following information at hand if it is
necessary to contact a local service center regarding service
or repair of this unit:
1. Obtain the unit Model Number and Serial Number from
the unit data decal. See Controls for location.
2. Obtain the engine Model/Type/Code numbers from the
engine label. See Controls for location. Please note that
the model number may vary slightly from that
presented herein.
Storage
The Rheem / Ruud Home Generator System is designed for
continuous backup operational duty. As such, there is no
need to take any storage precautions. However, if it becomes
necessary to take the system out of service for an extended
period, call Technical Services at (877) 369-9400, between
8:00 AM and 5:00 PM CT for specific recommendations.
16
Refer to engine manual for oil fill information.
Damage to equipment resulting from failure to follow this
instruction will void warranty.
NOTICE
Any attempt to crank or start the engine before it has been
properly serviced with the recommended oil will result in
equipment failure.
Do not expose generator to excessive moisture, dust, dirt, or
corrosive vapors.
Do not insert any objects through cooling slots.
NOTICE
Improper treatment of generator can damage it and shorten
its life.
Figure 5 — Oil Drain Fitting
Not for
Reproduction
Troubleshooting
17
Problem Cause Correction
Engine is running, but no AC output is
available.
1. Circuit breaker open or defective.
2. Fault in generator.
3. Poor wiring connections or
defective transfer switch.
1. Reset or replace circuit breaker.
2. Contact local service facility.
3. Check and repair.
Engine runs good at no-load but "bogs
down" when loads are connected.
1. Short circuit in a connected load.
2. Generator is overloaded.
3. Shorted generator circuit.
4. Fuel Pressure is incorrect.
5. Natural gas fuel mixture is
incorrect.
1. Disconnect shorted electrical load.
2. See Essential Circuits.
3. Contact local service facility.
4. See The Gaseous Fuel System in
the Installation Manual.
5. See The Gaseous Fuel System in
the Installation Manual.
Engine will not start; or starts and runs
rough.
1. 15 Amp fuse missing or blown.
2. Out of fuel.
3. Failed battery.
1. Install (new) 15 Amp fuse. See
Controls.
2. Open fuel valve(s); check propane
tank.
3. Replace battery.
Engine shuts down during operation.
1. Out of fuel.
2. Fault indicator blinking.
1. Check fuel valves, fill propane tank.
2. Count blinks and refer to Fault
Detection System.
Loss of power on essential circuits.
1. Generator circuit breaker is open.
2. Transfer switch problems.
1. Reset circuit breaker.
2. See the transfer switch manual.
Not for
Reproduction
Warranty
18
PROTECH™ Residential Standby Generators
Models: GEN12S GEN15S GEN20B GEN25B GEN30B
SCOPE of WARRANTY:
· This Limited Warranty provides that a replacement will be furnished for any part of the product which fails in normal use and service during the
Applicable Warranty Period specified, in accordance with the warranty’s terms. The replacement part is warranted for only the unexpired portion of the
original Applicable Warranty Period.
EXCEPTIONS:
· Commercial applications are not covered.
· Units installed as prime power source are not covered.
· Installations for the purpose of life support situations are not covered.
EFFECTIVE DATE of WARRANTY COVERAGE:
The Effective Date is the date of installation if properly documented; otherwise it is the date of manufacture plus six (6) months.
APPLICABLE WARRANTY PERIODS for VARIOUS PARTS:
All Residential Standby Generator Parts are warranted for an Applicable Warranty Period of Four (4) YEARS or 1500 operating hours, whichever occurs
first, after the Effective Date, except for the following specified product parts.
Transfer Switches - Transfer Switches (TS-100 and TS-200)carry a 3 year warranty for all parts.
Engine - The Briggs & Stratton engine warranty is covered by the manufacturer. Refer to Vanguard manual MS-3235
STANDARD PROVISIONS and CONDITIONS:
EXCLUSIONS - THIS WARRANTY WILL NOT APPLY: a) to damages, malfunctions or failures resulting from failure to properly install, operate or maintain the
unit in accordance with the manufacturer’s instructions provided; b) to damages, malfunctions or failures resulting from abuse, accident, fire, flood and
the like; c) to parts used in connection with normal maintenance, such as adjustments, fuel system cleaning and obstruction due to chemical, dirt,
carbon, lime and so forth; d) to units which are not installed in the United States of America or Canada; e) to units which are not installed in accordance
with applicable local codes, ordinances and good trade practices; f) to damages, malfunctions or failures caused by the use of any attachment,
accessory or component not authorized by the manufacturer; g) to wear items such as oil gauges, o-rings, filters fuses, or spark plugs etc.
SHIPPING COSTS: This Warranty does NOT cover shipping costs. You will be responsible for the cost of shipping warranty replacement parts from our factory
to our distributor and from the distributor to the location of your product. You also are responsible for any shipping cost of returning the failed part to
the distributor.
SERVICE LABOR RESPONSIBILITY: This Warranty does NOT cover any labor expenses for service, NOR for removing or reinstalling parts. All such expenses
are your responsibility, unless a service labor agreement exists between you and your contractor.
HOW TO OBTAIN WARRANTY PERFORMANCE: You must promptly report any failure covered by this warranty to the installing contractor or distributor.
Normally, the installing contractor from whom the unit was purchased will be able to take the necessary corrective action by obtaining through his
distributor any replacement parts. If the contractor is not available, simply contact any other local contractor handling RHEEM, RUUD or PROTECH air
conditioning products. The name and location of a local contractor can usually be found in your telephone directory or by contacting a RHEEM, RUUD
or PROTECH air conditioning distributor. If necessary, the following office can advise you of the nearest distributor:
4744 Island Ford Road, Randleman, NC 27317
HOWEVER, ANY REPLACEMENTS ARE MADE SUBJECT TO VALIDATION OF IN-WARRANTY COVERAGE. An item to be replaced must be made available
in exchange for the replacement.
EXCLUSIVE WARRANTY - LIMITATION OF LIABILITY:
This Limited Warranty is the ONLY warranty for the unit given by the manufacturer. No one is authorized to make any warranties on their behalf. ANY
IMPLIED WARRANTIES, INCLUDING MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE
APPLICABLE WARRANTY PERIODS SPECIFIED ABOVE. RHEEM’S SOLE LIABILITY WITH RESPECT TO DEFECTIVE PARTS OR FAILURES SHALL BE AS
SET FORTH IN THIS LIMITED WARRANTY, AND ANY CLAIMS FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXPRESSLY EXCLUDED. Some
states do not allow limitations on how long an implied warranty lasts, or for the exclusion of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This Limited Warranty gives you specific legal rights, and you may also have other rights which vary from
state to state. 202249E, Rev. -, 12/20/2006
RHEEM SALES COMPANY
Randleman NC
“In the spirit of continuous improvement, we reserve the right to make changes without notice.”
Not for
Reproduction
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60

Simplicity 040254-0 Manuel utilisateur

Catégorie
Groupes électrogènes
Taper
Manuel utilisateur