Simplicity 030663-01 Manuel utilisateur

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

MILWAUKEE, WISCONSIN, U.S.A.

Manual No. 80012136 Revision -

Portable Generator

Operator’s Manual

This generator is certified in accordance with CSA (Canadian Standards Association) standard C22.2 No. 100-04

(motors and generators) and rated in accordance with PGMA (Portable Generator Manufacturers’ Association)

standard PGMA G200 (Standard for Testing and Validating Performance of Portable Generators).

2 BRIGGSandSTRATTON.COM

Thank you for purchasing this quality-built Briggs & Stratton® generator. We are pleased that you’ve placed your

confidence in the Briggs & Stratton brand. When operated and maintained according to the instructions in this

manual, your Briggs & Stratton generator will provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with generator

products and how to avoid them. This generator is designed and intended only for supplying electrical power

for operating compatible electrical lighting, appliances, tools and motor loads, and is not intended for any other

purpose. It is important that you read and understand these instructions thoroughly before attempting to start or

operate this equipment. Save these original instructions for future reference.

This generator requires final assembly before use. Refer to the Assembly section of this manual for

instructions on final assembly procedures. Follow the instructions completely.

Where to Find Us

You never have to look far to find Briggs & Stratton support and service for your generator. Consult your Yellow

Pages. There are over 30,000 Briggs & Stratton authorized service dealers worldwide who provide quality service.

You can also contact Briggs & Stratton Customer Service by phone at (800) 743-4115, or on the Internet at

BRIGGSandSTRATTON.COM.

Generator Engine

Model Number ______________________ Model Number ________________________

Revision ___________________________ Type Number _________________________

Serial Number _______________________ Code Number _________________________

Date Purchased ____________________

Table of Contents

Safe Operation Checklist ............... 3

Operator Safety....................... 4

Assembly............................ 9

Features and Controls ................ 14

Operation........................... 17

Maintenance ........................ 21

Troubleshooting ..................... 26

Warranty ........................... 29

Product Specifications ................ 32

Common Service Parts ............... 32

BRIGGS & STRATTON POWER PRODUCTS is a registered

trademark of Briggs & Stratton Corporation

Milwaukee, WI, USA

3

Safe Operation Checklist

Safe operation of the portable generator requires the completion of the following tasks:

Carbon Monoxide (CO) Alarm

Carbon monoxide (CO) alarm(s) in working order.

Smoke Alarm

Smoke alarm(s) in working order.

Generator Location

Generator placed in a Carbon Monoxide (CO) safe zone. See Generator Location to reduce the Risk of

Carbon Monoxide Poisoning.

Generator placed in a fire safe zone. See Generator Location to reduce the Risk of Fire.

Generator located on flat and level surface.

Oil and Fuel

Engine has proper oil level. See Verify Engine Oil Level.

Fuel tank filled at or below baffle. See Add Fuel.

Inspect fuel lines, tank, cap and fittings each time before using generator. DO NOT use if fuel leak or damage

is found.

Electrical

When connecting to a buildings electrical system install listed transfer equipment. See Connecting to a

Building’s Electrical System.

Electrical cords are rated for intended loads. See Cord Sets and Receptacles.

Electrical cords do not run through doorways, windows, holes in ceilings, walls or floors.

Inspect electrical cords thoroughly before each use. DO NOT use if damaged.

All labeled electrical cord safeties are understood and being followed.

Operation

Start engine. See Starting the Engine.

4 BRIGGSandSTRATTON.COM

Operator Safety

Safety Labels

The generator safety labels shown below and on the next page are placed on your portable generator to draw

attention to potential safety hazards.

202997

5

6 BRIGGSandSTRATTON.COM

Equipment Description

Read this manual carefully and become

familiar with your generator. Know its

applications, its limitations and any hazards

involved.

The generator is an engine-driven, revolving field,

alternating current (AC) generator equipped with a

voltage regulator. The voltage regulator is designed to

automatically maintain a constant output voltage level.

It was designed to supply electrical power for operating

compatible electrical lighting, appliances, tools and

motor loads. The generator’s revolving field is driven at

about 3600 rpm by a single cylinder engine.

NOTICE

Exceeding generators wattage/amperage

capacity could damage generator and/or electrical

devices connected to it.

• DO NOT exceed the generator’s wattage/amperage

capacity. See Don’t Overload Generator in the Operation

section.

Every effort has been made to ensure that the

information in this manual is both accurate and current.

However, the manufacturer reserves the right to

change, alter or otherwise improve the generator and

this documentation at any time without prior notice.

The Emission Control System for this generator is

warranted for standards set by the Environmental

Protection Agency and the California Air Resources

Board.

This spark ignition system complies with the Canadian

standard ICES-002.

Important Safety Information

The manufacturer cannot possibly anticipate every

possible circumstance that might involve a hazard.

The warnings in this manual, and the tags and decals

affixed to the unit are, therefore, not all-inclusive.

If you use a procedure, work method or operating

technique that the manufacturer does not specifically

recommend, you must satisfy yourself that it is safe

for you and others. You must also make sure that the

procedure, work method or operating technique that

you choose does not render the generator unsafe.

Safety Symbols and Meanings

The safety alert symbol indicates a potential

personal injury hazard. A signal word (DANGER,

WARNING, or CAUTION) is used with the alert symbol

to designate a degree or level of hazard seriousness.

A safety symbol may be used to represent the type of

hazard. The signal word NOTICE is used to address

practices not related to personal injury.

DANGER indicates a hazard which, if not avoided,

will result in death or serious injury.

WARNING indicates a hazard which, if not

avoided, could result in death or serious injury.

CAUTION indicates a hazard which, if not

avoided, could result in minor or moderate injury.

NOTICE address practices not related to personal

injury.

Fire

Explosion

Toxic Fumes

Hot Surface

Moving Parts

Electrical Shock

Kickback

Flying Objects

Operator’s Manual

7

WARNING The engine exhaust from this

product contains chemicals known to the State of

California to cause cancer, birth defects, or other

reproductive harm.

WARNING Certain components in this product

and related accessories contain chemicals known to

the State of California to cause cancer, birth defects

or other reproductive harm. Wash hands after

handling.

WARNING

• This generator does not meet U. S. Coast Guard

Regulation 33CFR-183 and should not be used on

marine applications.

• Failure to use the appropriate U. S. Coast Guard

approved generator could result in death or serious injury.

WARNING Fuel and its vapors are extremely

flammable and explosive which

could cause burns, fire or explosion

resulting in death or serious injury.

WHEN ADDING OR DRAINING FUEL

• Turn generator engine OFF and let it cool at least 2

minutes before removing fuel cap. Loosen cap slowly to

relieve pressure in tank.

• Fill or drain fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

• Check fuel lines, tank, cap and fittings frequently for

cracks or leaks. Replace if necessary.

• DO NOT light a cigarette or smoke.

WHEN STARTING EQUIPMENT

• Ensure spark plug, muffler, fuel cap, and air cleaner are

in place.

• DO NOT crank engine with spark plug removed.

WHEN OPERATING EQUIPMENT

• DO NOT operate this product inside any building,

carport, porch, mobile equipment, marine applications, or

enclosure.

• DO NOT tip engine or equipment at angle which causes

fuel to spill.

• DO NOT stop engine by moving choke control to

CHOKE (

) position.

WHEN TRANSPORTING, MOVING OR REPAIRING

EQUIPMENT

• Transport/move/repair with fuel tank EMPTY or with fuel

shutoff valve OFF (0).

• DO NOT tip engine or equipment at angle which causes

fuel to spill.

• Disconnect spark plug wire.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN

TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers, or other appliances that have pilot light or other

ignition source because they could ignite fuel vapors.

WARNING Starter cord kickback (rapid

retraction) will pull hand and arm toward

engine faster than you can let go which

could cause broken bones, fractures,

bruises, or sprains resulting in serious injury.

• When starting engine, pull cord slowly until resistance is

felt and then pull rapidly to avoid kickback.

• NEVER start or stop engine with electrical devices

plugged in and turned on.

WARNING POISONOUS GAS HAZARD.

Engine exhaust contains carbon monoxide,

a poisonous gas that could kill you in

minutes. You CANNOT smell it, see it, or

taste it. Even if you do not smell exhaust fumes, you

could still be exposed to carbon monoxide gas.

• Operate this product ONLY outside far away from

windows, doors and vents to reduce the risk of carbon

monoxide gas from accumulating and potentially being

drawn towards occupied spaces.

• Install battery-operated carbon monoxide alarms or

plug-in carbon monoxide alarms with battery back-up

according to the manufacturer’s instructions. Smoke

alarms cannot detect carbon monoxide gas.

• DO NOT run this product inside homes, garages,

basements, crawlspaces, sheds, or other partially-

enclosed spaces even if using fans or opening doors

and windows for ventilation. Carbon monoxide can

quickly build up in these spaces and can linger for hours,

even after this product has shut off.

• ALWAYS place this product downwind and point the

engine exhaust away from occupied spaces.

If you start to feel sick, dizzy, or weak while using this

product, get to fresh air RIGHT AWAY. See a doctor. You

may have carbon monoxide poisoning.

8 BRIGGSandSTRATTON.COM

NOTICE

Exceeding generators wattage/amperage

capacity could damage generator and/or electrical

devices connected to it.

• DO NOT exceed the generator’s wattage/amperage

capacity. See Don’t Overload Generator in the Operation

section.

• Start generator and let engine stabilize before connecting

electrical loads.

• Connect electrical loads in OFF position, then turn ON for

operation.

• Turn electrical loads OFF and disconnect from generator

before stopping generator.

NOTICE

Improper treatment of generator could

damage it and shorten its life.

• Use generator only for intended uses.

• If you have questions about intended use, ask dealer or

contact local service center.

• Operate generator only on level surfaces.

• DO NOT expose generator to excessive moisture, dust,

dirt, or corrosive vapors.

• DO NOT insert any objects through cooling slots.

• If connected devices overheat, turn them off and

disconnect them from generator.

• Shut off generator if:

-electrical output is lost;

-equipment sparks, smokes, or emits flames;

-unit vibrates excessively.

WARNING Starter and other rotating parts

could entangle hands, hair, clothing, or

accessories resulting in serious injury.

• NEVER operate generator without protective housing or

covers.

• DO NOT wear loose clothing, jewelry or anything that

could be caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.

CAUTION Excessively high operating speeds

could result in minor injury.

Excessively low operating speeds impose a heavy

load.

• DO NOT tamper with governor spring, links or other parts

to increase engine speed. Generator supplies correct

rated frequency and voltage when running at governed

speed.

• DO NOT modify generator in any way.

WARNING

Generator voltage could cause

electrical shock or burn resulting in death or

serious injury.

• Use listed transfer equipment, suitable for the intended

use, to prevent backfeed by isolating generator from

electric utility workers.

• When using generator for backup power, notify utility

company.

• Use a ground fault circuit interrupter (GFCI) in any damp

or highly conductive area, such as metal decking or steel

work.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are

worn, frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain or wet weather.

• DO NOT handle generator or electrical cords while

standing in water, while barefoot, or while hands or feet

are wet.

• DO NOT allow unqualified persons or children to operate

or service generator.

WARNING Exhaust heat/gases could ignite

combustibles, structures or damage

fuel tank causing a fire, resulting in

death or serious injury.

Contact with muffler area could cause burns

resulting in serious injury.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 ft. (1.5 m) of clearance on all sides of

generator including overhead.

• It is a violation of California Public Resource Code,

Section 4442, to use or operate the engine on any forest-

covered, brush-covered, or grass-covered land unless

the exhaust system is equipped with a spark arrester, as

defined in Section 4442, maintained in effective working

order. Other states or federal jurisdictions may have

similar laws.

Contact the original equipment manufacturer, retailer,

or dealer to obtain a spark arrester designed for the

exhaust system installed on this engine.

• Replacement parts must be the same and installed in the

same position as the original parts.

WARNING Unintentional sparking could cause

fire or electric shock resulting in

death or serious injury.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

GENERATOR

• Disconnect the spark plug wire from the spark plug and

place the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

9

Assembly

Your generator requires some assembly and is ready

for use after it has been properly serviced with the

recommended fuel and oil level is verified.

If you have any problems with the assembly of

your generator, please call the generator helpline

at (800) 743-4115. If calling for assistance, please

have the model, revision, and serial number from the

identification label available.

Unpack Generator

1. Set the carton on a rigid, flat surface.

2. Remove everything from carton except generator.

3. Open carton completely by cutting each corner

from top to bottom.

4. Leave generator on carton to install wheel kit.

The generator is supplied with:

• Operator’s manual

• Battery float charger

• Wheel kit

• Keys (2)

Install Wheel Kit

NOTICE Wheel kit is not intended for over-the-road use.

You will need the following tools to install these

components:

• 13 mm and 19 mm wrench

• Socket wrench with 10 mm and 16 mm sockets

Install the wheel kit as follows:

1. Tip generator so that engine side is down.

2. Slide axle stud (A) through mounting bracket with

threaded end facing out.

3. Insert retaining pin (B) through hole on axle stud.

4. Slide a wheel (C) over axle stud.

NOTICE Be sure to install wheel with raised hub inboard.

5. Attach wheel to axle stud with a washer (D), lock

washer (E) and nut (F). Tighten with a 16 mm

socket wrench and 19 mm wrench.

6. Place hub cap (G) into center of wheel and push

until it snaps into place.

7. Repeat steps 2 through 6 to secure second wheel.

8. Line up holes in support leg (H) with holes in

generator frame.

9. Attach support leg using 4 capscrews (J) and 4

hex nuts (K). Tighten with a 10 mm socket wrench

and 13 mm wrench.

10. Return generator to normal operating position

(resting on wheels).

Attach Negative Battery Cable

Your unit is equipped with electric start capability but

can be started manually. If you choose not to use the

electric start feature, you do not need to connect the

negative battery cable.

The sealed battery on the generator pre–installed

except for the negative (black) battery cable.

To install:

1. Cut off tie wrap securing loose end of negative

(black) cable.

2. Using 8 mm or 5/16” wrenches, remove nut (L),

lock washer (M) and flat washer (N) on negative

battery terminal (—).

3. Slide negative battery cable (P) over screw (Q) on

negative terminal.

4. Reattach washer and nut and tighten.

5. Verify that connections to battery and generator

are tight and secure.

NOTICE If your battery is discharged, charge prior

to use following the instructions in the section Battery

Charger.

WARNING Battery posts, terminals and related

accessories contain lead and lead compounds -

chemicals known to the State of California to cause

cancer and reproductive harm. Wash hands after

handling.

B

G

C

D

A

E

F

K

J

H

Q

P

L

M

N

10 BRIGGSandSTRATTON.COM

Verify Engine Oil Level

The generator engine is shipped from the factory filled

with oil (API SJ or higher 10W-30). This allows for

generator operation in the widest range of temperature

and climate conditions. Before starting the engine,

check oil level and ensure that engine is serviced as

described in Maintenance.

NOTICE Any attempt to crank or start the engine

before it has been properly filled with the recommended

oil could result in equipment failure.

• Refer to Maintenance for oil fill information.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

NOTICE See Oil in the Maintenance section to review

oil recomendations. Verify provided oil in engine is the

correct viscosity for current ambient temperature.

Add Fuel

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). For

high altitude use, see High Altitude.

• Gasoline with up to 10% ethanol (gasohol) is

acceptable.

NOTICE Use of unapproved fuels could damage

generator and voids warranty.

• DO NOT use unapproved gasoline such as E15 and E85.

• DO NOT mix oil in gasoline or modify engine to run on

alternate fuels.

To protect the fuel system from gum formation, mix

in a fuel stabilizer when adding fuel. See Storage.

All fuel is not the same. If you experience starting or

performance problems after using fuel, switch to a

different fuel provider or change brands. This engine is

certified to operate on gasoline. The emission control

system for this engine is EM (Engine Modifications).

1. Clean area around fuel fill cap, remove cap.

2. Slowly add unleaded gasoline (A) to fuel tank (B).

Be careful not to fill above the baffle (C). This allows

adequate space for fuel expansion as shown.

3. Install fuel cap and let any spilled fuel evaporate

before starting engine.

High Altitude

At altitudes over 5,000 ft. (1524 m), a minimum

85 octane / 85 AKI (89 RON) gasoline is acceptable.

To remain emissions compliant, high altitude

adjustment is required. Operation without this

adjustment will cause decreased performance,

increased fuel consumption, and increased emissions.

See an authorized dealer for high altitude adjustment

information. Operation of the engine at altitudes

below 2,500 ft. (762 m) with the high altitude kit is not

recommended.

System Ground

The generator has a system ground that connects the

generator frame components to the ground terminals

on the AC output receptacles. The system ground is

connected to the AC neutral wire (the neutral is bonded

to the generator frame).

Special Requirements

There may be Federal or State Occupational Safety

and Health Administration (OSHA) regulations, local

codes, or ordinances that apply to the intended use of

the generator. Please consult a qualified electrician,

electrical inspector, or the local agency having

jurisdiction:

• In some areas, generators are required to be

registered with local utility companies.

• If the generator is used at a construction site,

there may be additional regulations which must be

observed.

Connecting to a Building’s Electrical System

Connections for standby power to a building’s electrical

system must use a listed transfer switch installed by

a current licensed electrician. The connection must

isolate the generator power from the utility power and

must comply with all applicable laws and electrical

codes.

FUEL

TANK

C

B

A

WARNING Fuel and its vapors are extremely

flammable and explosive which could

cause burns, fire or explosion

resulting in death or serious injury.

WHEN ADDING FUEL

• Turn generator engine OFF and let it cool at least 2 minutes

before removing fuel cap. Loosen cap slowly to relieve

pressure in tank.

• Fill fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

• Check fuel lines, tank, cap and fittings frequently for

cracks or leaks. Replace if necessary.

• DO NOT light a cigarette or smoke.

11

Portable Generator Location

Before starting the portable generator there are two

equally important safety concerns regarding carbon

monoxide (CO) poisoning and fire that must be

addressed.

NOTICE Satisfying the RISK OF CARBON

MONOXIDE POISONING location requirements may

not satisfy the fire location requirements. Satisfying the

RISK OF FIRE location requirements may not satisfy

the CARBON MONOXIDE POISONING location

requirements.

Operation Location of Portable Generator to

REDUCE THE RISK OF CARBON MONOXIDE

POISONING

All fossil fuel burning equipment, such as a portable

generator, contains carbon monoxide (CO) gas in the

engine exhaust, a poisonous gas that could kill you in

minutes. You CANNOT smell it, see it, or taste it. Even

if you do not smell exhaust fumes, you could still be

exposed to carbon monoxide gas. The following must

be completed prior to starting the portable generator

engine:

• By law it is required in many states to have a

Carbon Monoxide (CO) alarm (A) in operating

condition in your home. Install/maintain battery-

operated carbon monoxide alarms or plug-in

carbon monoxide alarms with battery back-up

according to the manufacturer’s instructions. A

CO alarm is an electronic device that detects

hazardous levels of CO. When there is a buildup

of CO, the alarm will alert the occupants by

flashing visual indicator light and alarm. Smoke

alarms cannot detect CO gas.

• Operate this product ONLY outside far away from

windows, doors and vents to reduce the risk of

carbon monoxide gas from accumulating and

potentially being drawn towards occupied spaces.

• DO NOT run this product inside homes, garages,

basements, crawlspaces, sheds, or other partially-

enclosed spaces even if using fans or opening

doors and windows for ventilation. Carbon

monoxide can quickly build up in these spaces

and can linger for hours, even after this product

has shut off.

• Your neighbor(s) home may be exposed to the

engine exhaust from your portable generator and

must be considered when deciding on a location

for the safe operation of your portable generator.

• ALWAYS place this product downwind and point

the engine exhaust away from occupied spaces.

If you start to feel sick, dizzy, or weak while using this

product, get to fresh air RIGHT AWAY. See a doctor.

You may have carbon monoxide poisoning.

A

WARNING

Generator voltage could cause

electrical shock or burn resulting in death or

serious injury.

• Use listed transfer equipment, suitable for the intended

use, to prevent backfeed by isolating generator from

electric utility workers.

• When using generator for backup power, notify utility

company.

• Use a ground fault circuit interrupter (GFCI) in any damp

or highly conductive area, such as metal decking or steel

work.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are

worn, frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain or wet weather.

• DO NOT handle generator or electrical cords while

standing in water, while barefoot, or while hands or feet

are wet.

• DO NOT allow unqualified persons or children to operate

or service generator.

12 BRIGGSandSTRATTON.COM

EXAMPLE OF LOCATION TO REDUCE

THE RISK OF CARBON MONOXIDE POISONING

DO NOT OPERATE IN ANY OF THE FOLLOWING LOCATIONS

Only use OUTSIDE

and FAR AWAY from

windows, doors and vents.

Direct exhaust AWAY

from windows, doors,

and vents.

KEEP

FAR AWAY

CO Alarm

in Living Areas

E

X

H

A

U

S

T

(

C

O

)

Generator too

close to home

and exhaust

directed towards

windows, doors

and vents.

Garage

Attic

Living Area

Basement

Crawlspace

Entryway,

Porch

E

X

H

A

U

S

T

(

C

O

)

13

EXAMPLE OF LOCATION TO REDUCE THE RISK OF FIRE

Operation Location of Portable Generator to

REDUCE THE RISK OF FIRE

WARNING Exhaust heat/gases could ignite

combustibles, structures or damage fuel tank

causing a fire, resulting in death or serious

injury.

• Portable generator must be at least 5 ft. (1.5 m) from

any structure, overhang, trees, windows, doors, any wall

opening, shrubs, or vegetation over 12 inches (30.5 cm)

in height.

• DO NOT place portable generator under a deck or other

type of structure that may confine airflow.

• Smoke alarm(s) MUST be installed and maintained

indoors according to the manufacturer’s instructions/

recommendations. Carbon monoxide alarms cannot

detect smoke.

• DO NOT place portable generator in manner other than

shown.

Direct exhaust AWAY from

windows, doors, and vents.

E

X

H

A

U

S

T

(

C

O

)

5 ft. (1.5 m) min.

14 BRIGGSandSTRATTON.COM

Features and Controls

Read this Operator’s Manual and safety rules before operating your generator.

Compare the illustrations with your generator, to familiarize yourself with the locations of various controls

and adjustments. Save this manual for future reference.

A - Start Switch — Turn key to START (

) position to

start the engine. Turn key to OFF (0) position to

switch off engine.

B - Hour Meter — Displays and records how many

hours your generator has run (up to 9,999.9).

C - Rocker Switch Circuit Breaker — The

120/240 Volt AC, 30A locking receptacle is

provided with a 2 pole rocker switch circuit breaker

to protect the generator against electrical overload.

D - Choke Control — Used when starting a cold

engine.

E - Battery Float Charger Jack — Use battery float

charger jack to keep the starting battery charged

and ready for use.

F - 120/240 Volt AC, 30 Amp Locking Receptacle

— May be used to supply electrical power for the

operation of 120 and/or 240 Volt AC, 30 Amp,

single phase, 60 Hz electrical, lighting, appliance,

tool and motor loads.

G - 120 Volt AC, 20 Amp, GFCI Duplex Receptacles

— May be used to supply electrical power for the

operation of 120 Volt AC, 20 Amp, single phase,

60 Hz electrical, lighting, appliance, tool and motor

loads.

H - Circuit Breakers (AC) — The 120 Volt AC, 20A

GFCI duplex receptacles are provided with “push

to reset” circuit breakers to protect the generator

against electrical overload.

J - Oil Fill Cap/Dipstick — Check and add engine oil

here.

K - Oil Drain Plug — Drain engine oil here.

L - Grounding Fastener — Consult your local agency

having jurisdiction for grounding requirements in

your area.

M - Spark Arrester Muffler — Exhaust muffler lowers

engine noise and is equipped with a spark arrester

screen.

N - Air Cleaner — Protects engine by filtering dust

and debris out of intake air.

P - Recoil Starter — Used to start the engine

manually.

Q - Fuel Valve — Used to turn fuel supply on and off to

engine.

R - Fuel Tank — Capacity of seven (7) U.S. gallons

(26.5 l).

Items Not Shown:

Engine Identification — Provides model, type and

code of engine. Please have these readily available if

calling for assistance.

Identification Label — Provides model and serial

number of generator. Please have these readily

available if calling for assistance.

A

C

R

M

B

D

E

F

G

H

J

K

L

P

Q

N

15

Cord Sets and Receptacles

Use only high quality, well-insulated, grounded

extension cords with the generator’s receptacles.

Inspect extension cords before each use.

Check the ratings of all extension cords before you use

them. Check the operator’s manuals of devices for the

manufacturer’s recommendations.

A double pole rocker switch main circuit breaker is

provided to protect the locking receptacle. If this circuit

breaker is tripped, all receptacles are disconnected.

120/240 Volt AC, 30 Amp, Locking Receptacle

Use a NEMA L14-30 plug with this receptacle.

Connect a 4-wire cord set rated for 250 Volt AC loads

at 30 Amps (or greater). You can use the same 4-wire

cord if you plan to run a 120 Volt load.

This receptacle powers 120/240 Volt AC, 60 Hz,

single phase loads requiring up to 7200 watts of power

(7.2 kW) at 30 Amps for 240 Volts or two independent

120 Volt loads at 30 Amps each. The outlet is

protected by a two pole rocker switch circuit breaker.

NOTICE

Receptacles may be marked with rating

value greater than generator output capacity.

• NEVER attempt to power a device requiring more

amperage than generator or receptacle can supply.

• DO NOT overload the generator. See Don’t Overload

Generator.

120 Volt AC, 20 Amp, GFCI Duplex Receptacles

Each GFCI duplex receptacle is protected against

overload by a push–to–reset circuit breaker.

Use each receptacle to operate 120 Volt AC, single-

phase, 60 Hz electrical loads requiring up to 2,400 watts

(2.4 kW) at 20 Amps of current. Use cord sets that are

rated for 125 Volt AC loads at 20 Amps (or greater).

Ground Fault Protection

The duplex receptacles are equipped with Ground

Fault Circuit Interrupter (GFCI) protection. This device

meets applicable federal, state and local codes. The

generator’s locking receptacle is not protected by a

Ground Fault Circuit Interrupter (GFCI).

The GFCI protects against electrical shock that may be

caused if your body becomes a path which electricity

travels to reach ground. This could happen if you touch

a “Live” appliance or wire, or are touching plumbing or

other materials that connect to the ground.

When protected by a GFCI, one may still feel a shock,

but the GFCI should cut current off quickly enough so

that a person in normal health should not suffer any

serious electrical injury.

WARNING Damaged or overloaded electrical

cords could overheat, arc, and burn

resulting in death or serious injury.

• ONLY use cords rated for your loads.

• Follow all safeties on electrical cords.

• Inspect cord sets before each use.

240V

120V

W (Neutral)

X (Hot)

Y (Hot)

NEMA L14-30

Ground (Green)

4-Wire Cord Set

WARNING

Generator voltage could cause

electrical shock or burn resulting in death or

serious injury.

• Contact with the hot and neutral conductor at the same

time can cause electrical shock or burn, even if the circuit

is GFCI protected.

• Before using the GFCI receptacle, ALWAYS push the

test button to insure it works.

16 BRIGGSandSTRATTON.COM

Testing the GFCI

Test your GFCI outlet prior to each use, as follows:

• Push the “Test” button. The “Reset” button should

pop out, which should allow no power to reach the

outlet. Use a test lamp in each outlet to test this.

• If the GFCI tests good, restore power by pressing

the “Reset” button firmly until it is fully in place

and locks in that position. If the GFCI outlet

does not reset properly, do not use the outlet.

Call or take your generator to a local service

center.

• If the GFCI trips by itself at any time, reset and

test the outlet. If the reset button does not pop

out when the test button is pressed, do not

use the outlet. Call or take your generator to

a local service center.

Battery Charger

Use battery float charger jack to keep the starting

battery charged and ready for use. Battery charging

should be done in a dry location, such as inside a

garage.

1. Plug charger into unit’s “Battery Float Charger”

jack, which is located next to the start switch. Plug

battery charger into a 120 Volt AC wall receptacle.

2. Unplug charger from unit and wall outlet when

generator is being started and while it is in operation.

3. Keep this charger plugged in when generator is

not in use to prolong battery life. The charger has

a built in float equalizer and will not overcharge

the battery, even when plugged in for an extended

period of time.

NOTICE See Battery Maintenance for additional

information.

17

Operation

Starting the Engine

Disconnect all electrical loads from the generator. Use

the following start instructions:

1. Make sure unit is on a level surface.

NOTICE Failure to start and operate the unit on a

level surface will cause the unit not to start or shut

down during operation.

2. Turn the fuel valve (A) to the ON (I) position.

3. Pull choke control out to close CHOKE ( ).

4A. For electric starting, turn and hold key in start

switch to START ( ) position until generator

starts. To prolong the life of starter components,

DO NOT hold key in START ( ) position for

more than 5 seconds, and pause for at least

30 seconds between starting attempts.

• If engine starts, proceed to step 6.

• If engine fails to start, proceed to step 5.

NOTICE If battery is discharged, use manual starting

instructions.

4B. For manual starting, turn key in start switch to

RUN (I) position, grasp recoil handle and pull

slowly until slight resistance is felt. Then pull

rapidly one time only to start engine.

• If engine starts, proceed to step 6.

• If engine fails to start, proceed to step 5.

5. Push in the choke handle half way, turn key in

start switch to RUN (I) position and pull recoil

handle twice or turn and hold key in start switch to

START (

) position as described in step 4A.

• If engine fails to start, repeat steps 3 thru 4.

6. Open the choke gradually as the engine warms up

by pushing in on the choke handle.

NOTICE If engine floods, push choke handle all the

way in and crank until engine starts.

NOTICE If engine starts after 3 pulls but fails to run,

or if unit shuts down during operation, make sure unit

is on a level surface and check for proper oil level in

crankcase. This unit may be equipped with a low oil

protection device. If so, oil must be at proper level for

engine to start.

A

WARNING Starter cord kickback (rapid

retraction) will pull hand and arm toward

engine faster than you can let go which

could cause broken bones, fractures,

bruises, or sprains resulting in serious injury.

• When starting engine, pull cord slowly until resistance is

felt and then pull rapidly to avoid kickback.

• NEVER start or stop engine with electrical devices

plugged in and turned on.

WARNING Exhaust heat/gases could ignite

combustibles, structures or damage

fuel tank causing a fire, resulting in

death or serious injury.

Contact with muffler area could cause burns

resulting in serious injury.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 ft. (1.5 m) of clearance on all sides of

generator including overhead.

• It is a violation of California Public Resource Code,

Section 4442, to use or operate the engine on any forest-

covered, brush-covered, or grass-covered land unless

the exhaust system is equipped with a spark arrester, as

defined in Section 4442, maintained in effective working

order. Other states or federal jurisdictions may have

similar laws.

Contact the original equipment manufacturer, retailer,

or dealer to obtain a spark arrester designed for the

exhaust system installed on this engine.

• Replacement parts must be the same and installed in the

same position as the original parts.

18 BRIGGSandSTRATTON.COM

Connecting Electrical Loads

1. Let engine stabilize and warm up for a few

minutes after starting.

2. Ensure circuit breaker on control panel is in ON (I)

position.

3. Plug in and turn on the desired 120 and/or

240 Volt AC, single phase, 60 Hz electrical loads.

NOTICE When plugging into the 120 Volt

receptacles, plug items to be powered in sequence as

shown below.

NOTICE

• DO NOT connect 240 Volt loads to the 120 Volt

GFCI duplex receptacles.

• DO NOT connect 3-phase loads to the generator.

• DO NOT connect 50 Hz loads to the generator.

• DO NOT OVERLOAD THE GENERATOR. See

Don’t Overload Generator.

NOTICE

Exceeding generators wattage/amperage

capacity could damage generator and/or electrical

devices connected to it.

• DO NOT exceed the generator’s wattage/amperage

capacity. See Don’t Overload Generator in the Operation

section.

• Start generator and let engine stabilize before connecting

electrical loads.

• Connect electrical loads in OFF position, then turn ON for

operation.

• Turn electrical loads OFF and disconnect from generator

before stopping generator.

Stopping the Engine

1. Turn OFF and unplug all electrical loads from

generator panel receptacles. NEVER start or stop

engine with electrical devices plugged in and

turned ON.

2. Let engine run at no-load for several minutes

to stabilize internal temperatures of engine and

generator.

3. Turn key in start switch to OFF (0) position.

4. Move fuel valve to OFF (0) position.

Low Oil Shutdown

If the engine oil drops below a preset level, an oil

switch will stop the engine. Check oil level with

dipstick.

If oil level is between ADD and FULL mark on

dipstick:

1. DO NOT try to restart the engine.

2. Contact an Authorized Briggs & Stratton Service

Dealer.

3. DO NOT operate engine until oil level is corrected.

If oil level is below ADD mark on dipstick:

1. Add oil to bring level to FULL mark.

2. Restart engine and if the engine stops again a low

oil condition may still exist. DO NOT try to restart

the engine.

3. Contact an Authorized Briggs & Stratton Service

Dealer.

4. DO NOT operate engine until oil level is corrected.

Cold Weather Operation

Under certain weather conditions (temperatures

below 40°F [4°C] combined with high humidity), your

generator may experience icing of the carburetor and/

or the crankcase breather system. To reduce this

problem, you need to perform the following:

1. Make sure generator has clean, fresh fuel.

2. Turn the fuel valve to the ON (I) position.

3. Use SAE 5W-30 oil.

4. Check oil level daily or after every eight (8) hours

of operation.

5. Maintain generator following Maintenance

Schedule in Maintenance section.

6. Shelter unit from elements.

WARNING Fuel and its vapors are extremely

flammable and explosive which could

cause burns, fire or explosion

resulting in death or serious injury.

• DO NOT stop engine by moving choke lever to

CHOKE (

) position.

1

4

2

3

19

Creating a Temporary Cold Weather Shelter

1. For temporary shelter, the original shipping carton

can be used.

2. Cut off top carton flaps and one long side of

carton to expose muffler side of unit. If required,

tape up other sides of carton to fit over generator

as shown.

NOTICE If required, remove wheel kit to fit carton

over generator as shown.

3. Cut appropriate slots to access receptacles of

unit.

4. Face exposed end away from wind and elements.

5. Locate generator as described in the section

Generator Location. Keep exhaust gas from

entering a confined area through windows, doors,

ventilation intakes or other openings.

6. Start generator as described in the section

Starting the Engine, then place carton over

generator. Keep at least 5 ft. (1.5 m) clearance

on all sides of generator including overhead with

shelter in place.

7. Remove shelter when temperatures are above

40°F [4°C].

8. Turn engine OFF and let cool two (2) minutes

before refueling. Let any spilled fuel evaporate

before starting engine.

Building a Cold Weather Shelter

1. Using non combustible material with a fire rating

of at least one hour, build a shelter that will

enclose three sides and the top of the generator.

Make sure muffler side of generator is exposed.

NOTICE Contact your local building material supplier

for non combustible materials with a fire rating of at

least one hour.

NOTICE Be sure shelter can easily be repositioned

for change in wind direction.

2. DO NOT enclose generator any more than shown.

Shelter should hold enough heat created by the

generator to prevent icing problem.

NOTICE If a wheel kit is installed on the generator,

enlarge shelter accordingly.

3. Follow steps 3 through 8 as described previously

in Creating a Temporary Cold Weather Shelter.

WARNING Exhaust heat/gases could ignite

combustibles, structures or damage

fuel tank causing a fire, resulting in

death or serious injury.

Contact with muffler area could cause burns

resulting in serious injury.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 ft. (1.5 m) of clearance on all sides of

generator including overhead.

• Remove shelter when temperatures are above 40°F [4°C].

WARNING POISONOUS GAS HAZARD.

Engine exhaust contains carbon monoxide,

a poisonous gas that could kill you in

minutes. You CANNOT smell it, see it, or

taste it. Even if you do not smell exhaust fumes, you

could still be exposed to carbon monoxide gas.

• Operate this product ONLY outside far away from

windows, doors and vents to reduce the risk of carbon

monoxide gas from accumulating and potentially being

drawn towards occupied spaces.

• Install battery-operated carbon monoxide alarms or

plug-in carbon monoxide alarms with battery back-up

according to the manufacturer’s instructions. Smoke

alarms cannot detect carbon monoxide gas.

• DO NOT run this product inside homes, garages,

basements, crawlspaces, sheds, or other partially-

enclosed spaces even if using fans or opening doors and

windows for ventilation. Carbon monoxide can quickly

build up in these spaces and can linger for hours, even

after this product has shut off.

• ALWAYS place this product downwind and point the

engine exhaust away from occupied spaces.

If you start to feel sick, dizzy, or weak while using this

product, get to fresh air RIGHT AWAY. See a doctor. You

may have carbon monoxide poisoning.

Wind

20 BRIGGSandSTRATTON.COM

Don’t Overload Generator

Capacity

You must make sure your generator can supply

enough rated (running) and surge (starting) watts for

the items you will power at the same time. Follow these

simple steps:

1. Select the items you will power at the same time.

2. Total the rated (running) watts of these items.

This is the amount of power your generator must

produce to keep your items running. See Wattage

Reference Guide.

3. Estimate how many surge (starting) watts you will

need. Surge wattage is the short burst of power

needed to start electric motor-driven tools or

appliances such as a circular saw or refrigerator.

Because not all motors start at the same time, total

surge watts can be estimated by adding only the

item(s) with the highest additional surge watts to

the total rated watts from step 2.

Example:

Total Rated (Running) Watts = 3075

Highest Additional Surge (Starting) Watts = 1800

Total Generator Output Required = 4875

Power Management

To prolong the life of your generator and attached

devices, it is important to take care when adding

electrical loads to your generator. There should be

nothing connected to the generator outlets before

starting its engine. The correct and safe way to

manage generator power is to sequentially add loads

as follows:

1. With nothing connected to the generator, start the

engine as described in this manual.

2. Plug in and turn on the first load, preferably the

largest load you have.

3. Permit the generator output to stabilize (engine

runs smoothly and attached device operates

properly).

4. Plug in and turn on the next load.

5. Again, permit the generator to stabilize.

6. Repeat steps 4 and 5 for each additional load.

NEVER add more loads than the generator capacity.

Take special care to consider surge loads in generator

capacity, as described above.

* Wattages listed are approximate only. Check tool or

appliance for actual wattage.

Tool or Appliance

Rated*

(Running)

Watts

Additional

Surge

(Starting)

Watts

Essentials

Light Bulb - 75 watt 75 -

Deep Freezer 500 500

Sump Pump 800 1200

Refrigerator/Freezer - 18 Cu. Ft. 800 1600

Water Well Pump - 1/3 HP 1000 2000

Heating/Cooling

Window AC - 10,000 BTU 1200 1800

Window Fan 300 600

Furnace Fan Blower - 1/2 HP 800 1300

Kitchen

Microwave Oven - 1000 Watt 1000 -

Coffee Maker 1500 -

Electric Stove - Single Element 1500 -

Hot Plate 2500 -

Family Room

DVD/CD Player 100 -

VCR 100 -

Stereo Receiver 450 -

Color Television - 27” 500 -

Personal Computer w/17” monitor 800 -

Other

Security System 180 -

AM/FM Clock Radio 300 -

Garage Door Opener - 1/2 HP 480 520

Electric Water Heater - 40 Gallon 4000 -

DIY

Quartz Halogen Work Light 1000 -

Airless Sprayer - 1/3 HP 600 1200

Reciprocating Saw 960 960

Electric Drill - 1/2 HP 1000 1000

Circular Saw - 7 1/4” 1500 1500

Miter Saw - 10” 1800 1800

Table Planer - 6” 1800 1800

Table Saw/Radial Arm Saw - 10” 2000 2000

Air Compressor - 1-1/2 HP 2500 2500

Tool or

Appliance

Rated (Running)

Watts

Additional Surge

(Starting) Watts

Window Air

Conditioner

1200 1800

Refrigerator 800 1600

Deep Freezer 500 500

Television 500 —

Light (75 Watts) 75 —

3075 Total

Running Watts

1800 Highest

Additional Surge

Watts

La page charge ...

Simplicity 030663-01 Manuel utilisateur

Ce manuel convient également à

Simplicity 030663-01 Manuel utilisateur

dans d''autres langues