Whirlpool 7MWTW1604DM0 Le manuel du propriétaire

Marque: Whirlpool

Modèle: 7MWTW1604DM0

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Ce manuel convient également à

Whir

TOP-LOADING

WASHER

USE AND CARE GUIDE

LAVEUSE A CHARGEMENT

PAR LE DESSUS

GUIDE D'UTILISATION ET

D'ENTRETIEN

Para una versi6n de estas instrucciones en espa_ol, visite www.whirlpool.com

Table of Contents

WASHER SAFETY ......................................................... 2

WHAT'S NEW UNDER THE LID? ................................. 3

CONTROL PANEL AND FEATURES ............................ 4

CYCLE GUIDE ............................................................... 5

USING YOUR WASHER ................................................ 6

WASHER MAINTENANCE ............................................ 8

TROUBLESHOOTING ................................................. 10

WARRANTY ................................................................. 14

ASSISTANCE OR SERVICE ........................ Back Cover

Table des matibres

Si_CURIT¢: DE LA LAVEUSE ...................................... 15

QUOI DE NEUF SOUS LE COUVERCLE? ................. 16

TABLEAU DE COMMANDE ET

CARACTC:RISTIQUES ................................................. 17

GUIDE DE PROGRAMMES ........................................ 19

UTILISATION DE LA LAVEUSE .................................. 20

ENTRETIEN DE LA LAVEUSE .................................... 23

DI_PANNAGE ............................................................... 25

GARANTIE ................................................................... 30

ASSISTANCE OU SERVICE ............ Couverture artiste

W10560163B

W10560164A=SP

WASHER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all

safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or

"WARNING." These words mean:

You can be killed or seriously injured if you don't

immediately follow instructions.

You can be killed or seriously injured if you don't

follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you

what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions,

including the following:

[] Read all instructions before using the washer.

[] Do not wash articles that have been previously cleaned

in, washed in, soaked in, or spotted with gasoline,

dry-cleaning solvents, other flammable, or explosive

substances as they give off vapors that could ignite or

explode.

[] Do not add gasoline, dry-cleaning solvents, or other

flammable, or explosive substances to the wash water.

These substances give off vapors that could ignite or

explode.

[] Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been used

for 2 weeks or more. HYDROGEN GAS IS

EXPLOSIVE. Ifthe hot water system has not been

used for such a period, before using the washing

machine, turn on all hot water faucets and let the water

flow from each for several minutes. This will release

any accumulated hydrogen gas. As the gas is

flammable, do not smoke or use an open flame during

Do not allow children to play on or in the washer. Close

supervision of children is necessary when the washer is used

near children.

Before the washer is removed from service or discarded,

remove the door or lid.

[] Do not reach into the washer if the drum, tub or agitator is

moving.

[] Do not install or store the washer where it will be exposed to

the weather.

[] Do not tamper with controls.

[] Do not repair or replace any part of the washer or attempt any

servicing unless specifically recommended in this manual or in

published user-repair instructions that you understand and

have the skills to carry out.

[] See "Electrical Requirements" located in the installation

instructions for grounding instructions.

this time.

SAVE THESE INSTRUCTIONS

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

WHAT'S NEW UNDER THE LID?

Your new washer will operate differently than your past agitator-style washer.

Lid Lock _lll Sounds

To allow for higher spin speeds, the lid will lock and

the Lid Locked light will turn on. When this light is

lit, the lid is locked and cannot be opened. When

this light is blinking, the washer is paused. When

this light is off, the lid can be opened. After a cycle

is started, water will enter washer and then lock. If

you need to open the lid to add a garment after this

point, you must press START/Pause and wait for the

lid to unlock. The lid will only unlock after washer

movement has stopped. Depending on when in the

cycle you try to pause, it may take several seconds

to several minutes for the lid to unlock. Press START/

Pause to resume the cycle.

At different stages of the wash cycle, you may

hear sounds and pauses that are different from

those of your previous washer. For example, you

may hear a clicking and hum at the beginning of

the cycle as the lid lock goes through a self-test.

There will be different kinds of humming and

whirring sounds as the agitator tests for load

balance or moves the load. And, sometimes,

you may hear nothing at all as the washer allows

time for clothes to soak.

Sensing

This washer will perform a series of spins to check

for load balance. During this time, a series of clicks

and a whirring noise signal that sensing technology

is determining if there is an off-balance load.

Spray Rinse

Select cycles default to a spray rinse. During these

cycles, you will hear water enter the washer as the

tub spins, allowing the rinse water to penetrate

clothes. Check the "Cycle Guide" for details.

iMPORTANT:

• After the washer basket fills to the selected water level, the lid must be closed before the wash cycle can start.

If filling stops with the lid open, close lid and press START button.

• Rinse option must be selected to 1 Rinse with Softener or 2 Rinses with Softener to ensure fabric softener

dispenses at the correct time.

CONTROL PANEL AND FEATURES

Not all features and options are available on all models.

Appearance may vary.

LOAD SiZE

Select the setting most suitable for your load. Small

will add a low amount of water for smaller loads and Ex

Large will add the most amount of water for large or bulky

loads. Items need to move freely. Tightly packing can lead to

poor cleaning performance and may increase wrinkling and

tangling.

O WASH TEMP

Wash Temp senses and maintains uniform water

temperatures by regulating incoming hot and cold water.

Select a wash temperature based on the type of fabric

and soils being washed. For best results and following

the garment label instructions, use the warmest wash

water safe for your fabric.

• On some models and cycles, warm and hot water may

be cooler than your previous washer.

• Even in a cold and cool water wash, some warm water

may be added to the washer to maintain a minimum

temperature.

WASH CYCLE KNOB

Use the Wash Cycle knob to select cycles on your washer.

Knob does not advance during the progress of the cycle,

see cycle status lights for each stage of the process. See

"Cycle Guide" for detailed descriptions of cycles.

RINSE OPTIONS

The following options may be added to most cycle.

See "Cycle Guide" for additional details.

1 RINSE

This option is used to limit a cycle to one rinse.

2 RINSES

This option can be used to automatically add a

second rinse to most cycles.

1 RINSE with SOFTENER

This option must be selected if using fabric softener

during a cycle. It ensures that fabric softener is added

at the correct time in the rinse for even distribution.

2 RINSES with SOFTENER

This option turns on both the Fabric Softener and

the 2 Rinses option.

START/PAUSE BUTTON

Press to start the selected cycle; press again to pause the

cycle and unlock the lid. Press and hold for 3 seconds

to cancel a cycle.

NOTE: if the washer is spinning, it may take several

minutes to unlock the lid.

CYCLE STATUS LIGHTS iNDiCATOR

Progress C_) C_) ([_) C_ Q C_

Fitl Wash Rinse Spin Done Locked

The Cycle Status Lights show the progress of a cycle.

At each stage of the process, you may notice sounds or

pauses that are different from traditional washers.

FILL

When the START/Pause button is pressed, the washer will

fill to the selected water level. Ifthe lid is closed when the

washer is done filling the lid will lock and the washer will

begin operation.

If the lid is open when the water stops entering the

washer, the cycle will not begin until the lid has been

closed and the START/Pause button is pressed. If the

cycle has not been started within 10 minutes of the water

filling the washer, the washer will pump out the water.

NOTE: Avoid opening lid during sensing phase. The

sensing process will start over when the washer is

restarted. The FILL light may also come on during the

Soak and Wash portions of the cycle. This is normal. To

restart the washer after the lid has been opened press

START.

WASH

You will hear the agitator moving the load. The motor

sounds may change at different stages in the cycle.

The wash time is determined by the selected soil level.

RINSE

You will hear sounds similar to the wash cycle as the

washer rinses and moves the load. You may hear the

motor turning on briefly (short hum) to move the basket

while filling. Fabric softener will be added if the 1 Rinse

with Softener or 2 Rinses with Softener option was

selected.

Some cycles use spray rinsing. After draining and

spinning out wash water, the washer will continue to

spin and spray in rinse water for the entire rinse time.

SPiN

The washer spins the load at increasing speeds for

proper water removal, based on the selected cycle

and spin speed.

DONE

Once the cycle is complete, this light will come on.

Remove the load promptly for best results.

CYCLE GUIDE

For best fabric care, choose the cycle that best fits the load being washed.

Not all cycles and options are available on all models.

LiD LOCKED

To allow for higher spin speeds, the

lid will lock and the Lid Locked light

will turn on. When this light is lit, the

lid is locked and cannot be opened.

When this light is blinking, the washer

is paused. When this light is off, the lid

can be opened.

If you need to open the lid, press

START/Pause. The lid will unlock once

the washer movement has stopped.

This may take several minutes if the

load was spinning at high speed.

Press START/Pause again to resume

the cycle.

CZD

Locked

Cottons, linens,

and mixed garment

loads

Cottons, linens,

and mixed garment

loads

Cottons, linens,

and mixed garment

loads

No-iron fabrics,

cottons, perm

press, linens,

synthetics

No-iron fabrics,

cottons, perm

press, linens,

synthetics

Machine-wash

silks, hand-washed

fabrics

Hand-washed

garments or

dripping wet items

Swimsuits and

items requiring

rinsing without

detergent

No clothes in

washer

Normal Light

Normal

Normal Heavy

Casual

Regular

Casual

Light

Delicate

Drain &

Spin

Rinse &

Spin

Clean Washer

with

affresh <e

Hot

Warm

Cool

Cold

Tap Cold

Hot

Warm

Cool

Cold

Tap Cold

Hot

Warm

Cool

Cold

Tap Cold

Hot

Warm

Cool

Cold

Tap Cold

Hot

Warm

Cool

Cold

Tap Cold

Hot

Warm

Cool

Cold

Tap Cold

N/A

Cold rinse only

Hot

Warm

Cool

Cold

Tab Cold

NOTE: If you are using fabric softener, be sure to select the

*All rinses are cold.

High

Low

High

Low

Rinse with

Use this cycle for lightly soiled mixed loads. This cycle

features a spray rinse.

Use this cycle for normally soiled cottons and mixed fabric

loads. This cycle features a spray rinse.

Use this cycle for heavily soiled or sturdy items. This cycle

features a spray rinse. Use this cycle for cleaning the interior

of the washer. See "Washer Care."

Use this cycle to wash loads of no-iron fabrics such as sport

shirts, blouses, casual business clothes, permanent

press, and blends.

Use this cycle to wash lightly-soiled loads of no-iron fabrics

such as sport shirts, blouses, casual business clothes,

permanent press, and blends.

Use this cycle to wash lightly soiled garments indicating

"Machine Washable Silks" or "Gentle" cycle on the care

label. Place small items in mesh garment bags before wash-

ing. This cycle features a spray rinse.

This cycle uses a spin to shorten drying times for heavy

fabrics or special-care items washed by hand. Use this

cycle to drain washer after cancelling a cycle or completing

a cycle after a power failure.

Combines a rinse and high speed spin for loads requiring

an additional rinse cycle or to complete a load after power

interruption. Also use for loads that require rinsing only.

Use this cycle every 30 washes to keep the inside of your

washer fresh and clean. This cycle uses a higher water level.

Use with affresh_*_Washer Cleaner tablet or liquid chlorine

bleach to thoroughly clean the inside of your washer. This

cycle should not be interrupted. See "Washer Care."

iMPORTANT: Do not place garments or other items in the

washer during the Clean Washer with affresh _'_)cycle. Use

this cycle with an empty wash tub.

Softener or 2 Rinses with Softener option.

USING YOUR WASHER

Fire Hazard

Never place items in the washer that are dampened

with gasoline or other flammable fluids,

No washer can completely remove oil,

Do not dry anything that has ever had any type of oil on

it (including cooking oils).

Doing so can result in death, explosion, or fire.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Sort and prepare your laundry

* Empty pockets. Loose change, buttons, or any small object

can pass under the agitator and become trapped, causing

unexpected sounds.

, Sort items by recommended cycle, water temperature,

and colorfastness.

* Separate heavily soiled items from lightly soiled.

= Separate delicate items from sturdy fabrics.

= Do not dry garments if stains remain after washing, because

heat can set stains into fabric.

* Treat stains promptly.

= Close zippers, fasten hooks, tie strings and sashes, and

remove non-washable trim and ornaments.

= Mend rips and tears to avoid further damage to items

during washing.

Helpful Tips:

* When washing water-proof or water-resistant items, load

evenly.

= Use mesh garment bags to help avoid tangling when washing

delicate or small items.

,, Turn knits inside out to avoid pilling. Separate lint-takers from

lint-givers. Synthetics, knits, and corduroy fabrics will pick up

lint from towels, rugs, and chenille fabrics.

NOTE: Always read and follow fabric care label instructions to

avoid damage to your garments.

Add laundry products

Add a measured of amount of detergent or single-dose

laundry packet into the basket.

If using Oxi-type boosters, color-safe bleach, or fabric

softener crystals, add to the bottom of the washer basket

before adding clothes.

NOTE: Follow the manufacturer's instructions to determine

the amount of laundry products to use.

3= Load laundry into washer

Load garments in loose heaps evenly

around basket wall. For best results, do

not pack the load tightly. Do not wrap

large items such as sheets around the

agitator; load them in loose piles around

the sides of the basket. Try mixing

different sized items to reduce tangling.

IMPORTANT: Do not tightly pack or

force items into washer. Items need to

move freely for best cleaning and to reduce

wrinkling and tangling.

Add liquid chlorine bleach

to dispenser

Do not overfill, dilute, or use more than 1 cup (250 mL).

Do not use color-safe bleach or Oxi products in the same

cycle with liquid chlorine bleach.

Add fabric softener to dispenser

(on some models}

Pour a measured amount of liquid fabric

softener into dispenser; always follow

manufacturer's directions for correct amount

of fabric softener based on your load size.

Dilute liquid fabric softener by filling the dispenser with warm

water until liquid reaches the underside of the rim. See max fill

line arrows.

RINSE OPTIONS

IMPORTANT: Rinse option must be selected .......

to 1 Rinse with Softener or 2 Rinses with

Softener to ensure proper distribution of the

fabric softener during the final rinse portion

of the cycle.

Adding Liquid Fabric Softener Manually

to Wash Load

During the final rinse, wait until the washer has completed

filling, press the START/Pause button to pause the washer.

Lift the lid and add the measured recommended amount of

liquid fabric softener. Do not use more than the recommended

amount. Close the lid and press the START/Pause button again

to start the washer.

_f.....

f6= Select cycle

Normal

Light o Heavy

Drain & Spin o

Regular

Casual

o Light

Rinse & Spin o o Delicate

Clean Washer

with af_r_$ll

_ =

Turn cycle knob to choose your wash cycle. For more

information, see "Cycle Guide".

7, Select LOAD SiZE

LOAD SiZE

E× Large o

Large o

Medium o

Select the load size setting most suitable for your load. Small

will add a low amount of water for smaller loads and Ex Large

will add the most amount of water for large or bulky loads.

Items need to move freely.

8, Select WASH TEMP

WASH TEMP

Hot o

Wam i!

Cool o

Cold o

Tap Cold o

Once you select a cycle, select the desired wash temperature

by turning the Wash Temp knob to the appropriate setting

based on your load. All rinses are tap cold.

NOTE: Always read and follow fabric care label instructions

to avoid damage to your garments.

Wash Temp Suggested Fabrics

Hot

Some cold water is added to save Whites and pastels

energy. This will be cooler than Durable garments

your hot water heater setting. Heaw soils

Warm

Some cold water will be added, so

this will be cooler than what your

previous washer provided.

Bright colors

Moderate to light soils

Cool

Warm water may be added to

assist in soil removal and to help

Cold

This is the temperature from your

faucet. If your tap cold water is

very cold, warm water may be

added to assist in soil removal and

help dissolve detergent.

Colors that bleed

or fade

;: Dark colors that

;;::ibleed or fade

Light soils

Wash Temp Suggested Fabrics

Tap Cold

This is the temperature from Dark colors that

your faucet, bleed or fade

Light soils

fg. Select options, if desired

RINSE OPTIONS

o 1Rinse

o 2 Rinses

ol Rinse

with

softener

o 2 Rinses

with

so_ener

Select the desired cycle options. If you are using fabric

softener, be sure to select one of the Fabric Softener options.

Press START/Pause

to begin wash cycle

Start/Pause

Ho_d3 Seconds

to Cancel

Press the START/Pause button to start the wash cycle. When

the cycle has finished, the DONE indicator will light. Promptly

remove garments after cycle has completed to avoid odor,

reduce wrinkling, and rusting of metal hooks, zippers, and

snaps.

Unlocking the lid to add garments

If you need to open the lid to add 1 or 2 missed garments:

Press START/Pause; the lid will unlock once the

washer movement has stopped. This may take several

minutes if the load was spinning at high speed. Then close

lid and press START/Pause again to restart the cycle.

If lid is left open for more than 10 minutes, the water will pump

out automatically.

WASHER MAINTENANCE

f WATER INLET HOSES

Replace inlet hoses after 5 years of use to reduce the risk of

hose failure. Periodically inspect and replace inlet hoses if

bulges, kinks, cuts, wear, or leaks are found.

When replacing your inlet hoses, mark the date of replacement

on the label with a permanent marker.

NOTE: This washer does not include inlet hoses. See the

"Installation Instructions" for more information.

WASHER CARE

Recommendations to Help Keep Your Washer Clean and

Performing at its Best

1. Always follow the detergent manufacturer's instructions

regarding the amount of detergent to use. Never use more

than the recommended amount because that may increase

the rate at which detergent and soil residue accumulate

inside your washer, which in turn may result in undesirable

odor.

2. Use warm and hot wash water settings sometimes (not

exclusively cold water washes), because they do a better

job of controlling the rate at which soils and detergent

accumulate.

3. Always leave the washer lid open between uses to help dry

out the washer and prevent the buildup of odor-causing

residue.

Cleaning Your Top Loading Washer

Read these instructions completely before beginning the

routine cleaning processes recommended below. This Washer

Maintenance Procedure should be performed, at a minimum,

once per month or every 30 wash cycles, whichever occurs

sooner, to control the rate at which soils and detergent may

otherwise accumulate in your washer.

Cleaning the Inside of the Washer

To keep your washer odor-free, follow the usage instructions

provided above, and use this recommended monthly cleaning

procedure:

Recommended Cycle for Cleaning the Washer

Refer to the "Cycle Guide" for the optimal cycle for cleaning

the inside of the washer. Use this cycle with affresh e_Washer

Cleaner or liquid chlorine bleach as described below.

Begin procedure

1. afresh_ Washer Cleaner Cycle Procedure (Recommended

for Best Performance):

a. Open the washer lid and remove any clothing or items.

boPlace an affesh ®Washer Cleaner tablet in the bottom of

the washer basket.

coDo not place an affresh e_Washer Cleaner tablet in the

detergent dispenser.

doDo not add any detergent or other chemical to the washer

when following this procedure.

eoClose the washer lid.

f. Select the cycle recommended for cleaning the inside of

the washer.

goPress the START/Pause/Unlock button to start the cycle.

NOTE: For best results, do not interrupt cycle. If cycle must

be interrupted, press START/Pause/Unlock once or twice

(depending on model). After the cycle has stopped, run a

RINSE & SPIN cycle to rinse cleaner from washer.

2. Chlorine Bleach Procedure (Alternative}:

a. Open the washer lid and remove any clothing or items.

b. Add 1 cup (236 mL) of liquid chlorine bleach to the bleach

compartment.

NOTE: Use of more liquid chlorine bleach than is

recommended above could cause washer damage over

time.

coClose the washer lid.

d. Do not add any detergent or other chemical to the washer

when following this procedure.

eoSelect the cycle recommended for cleaning the inside of

the washer.

f WASHER CARE (cont.) "_

fo Press the START/Pause/Unlock button to start the cycle.

NOTE: For best results, do not interrupt cycle. If cycle must

be interrupted, press START/Pause/Unlock once or twice

(depending on model). After the cycle has stopped, run a

RINSE & SPIN cycle to rinse cleaner from washer.

Cleaning the Dispensers

After a period of using your washer, you may find some residue

buildup in the washer's dispensers. To remove residue from

the dispensers, wipe them with a damp cloth and towel dry.

Do not attempt to remove the dispensers or trim for cleaning.

The dispensers and trim are not removable. Ifyour model has

a dispenser drawer, however, remove the drawer and clean

it before or after you run the Clean Washer cycle. Use an all-

purpose surface cleaner, if needed.

Cleaning the Outside of the Washer

Use a soft, damp cloth or sponge to wipe away any spills. Use

only mild soaps or cleaners when cleaning external washer

surfaces.

IMPORTANT: To avoid damaging the washer's finish, do not

use abrasive products.

NON=USE AND VACATION CARE

Operate your washer only when you are home. If moving, or

not using your washer for a period of time, follow these steps:

1. Unplug or disconnect power to washer.

2. Turn off water supply to washer, to avoid flooding due

to water pressure surge.

f WINTER STORAGE CARE "_

IMPORTANT: To avoid damage, install and store washer

where it will not freeze. Because some water may stay in

hoses, freezing can damage washer. If storing or moving

during freezing weather, winterize your washer.

To winterize washer:

1. Shut off both water faucets; disconnect and drain water

inlet hoses.

2. Put 1 qt. (1 L) of R._,L-type antifreeze in basket and run

washer on RINSE & SPIN cycle for about 30 seconds

to mix antifreeze and remaining water.

3. Unplug washer or disconnect power.

f TRANSPORTING YOUR WASHER

Shut off both water faucets. Disconnect and drain water

inlet hoses.

If washer will be moved during freezing weather, follow

Winter Storage Care directions before moving.

Disconnect drain hose from drain system and drain any

remaining water into a pan or bucket. Disconnect drain

hose from back of washer.

Unplug power cord.

Place inlet hoses and drain hose inside washer basket.

Drape power cord over edge and into washer basket.

Place packing tray from original shipping materials back

inside washer, if you do not have packing tray, place heavy

blankets or towels into basket opening. Close lid and place

tape over lid and down front of washer. Keep lid taped until

washer is placed in new location.

RE! NSTALLING/USI NG WASHER AGAI N

To reinstall washer after non-use, vacation, winter storage,

or moving:

1. Refer to "Installation Instructions" to locate, level, and

connect washer.

2. Before using again, run washer through the following

recommended procedure:

To use washer again:

1. Flush water pipes and hoses. Reconnect water inlet hoses.

Turn on both water faucets.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

TROUBLESHOOTING

2. Plug in washer or reconnect power.

3. Run washer through Casual Regular cycle to clean washer

and remove antifreeze, if used. Use half the manufacturer's

recommended amount of detergent for a medium-size load.

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

if you experience | Possible Causes _ Solution

J !

Check the following for Front and rear feet must be in firm contact with floor, and

proper installation or washer must be level to operate properly.

see "Using Your

Washer" section.

Clicking or metallic

noises

Gurgling or humming

Humming

Feet may not be in contact with the

floor and locked.

Washer may not be level.

Load could be unbalanced.

Objects caught inwasher drain

system.

Washer may be draining water.

Load sensing may be occurring.

Washer not level.

Fill hoses not attached tightly.

Check floor for flexing or sagging. If flooring is uneven, a 3/4"

(19 mm) piece of plywood under your washer will reduce sound.

See "Level the Washer" in installation instructions.

Load dry items in loose heaps evenly around basket wall.

Adding wet items to washer or adding more water to basket

could unbalance washer.

Wash smaller loads to reduce imbalance.

Do not tightly pack. Avoid washing single items.

Use Normal cycle and Ex Large or Large load size for oversized,

non-absorbent items such as comforters or poly-filled jackets.

See "Cycle Guide" and "Using Your Washer" in this Use and

Care Guide.

Empty pockets before washing. Loose items such as coins

could fall between basket and tub or may block pump.

It may be necessary to call for service to remove items.

It is normal to hear metal items on clothing such as metal snaps,

buckles, or zippers touch against the basket.

It is normal to hear the pump making a continuous humming

sound with periodic gurgling or surging as final amounts of

water are removed during the Drain & Spin cycles.

You may hear the hum of the sensing spins after you have

started the washer. This is normal.

Check the following for Water may splash off basket if washer is not level. Check that

proper installation: load is not unbalanced or tightly packed.

Tighten fill-hose connection.

TROUBLESHOOTING

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

Check the following for Fill hose washers. Make sure all four fill hose flat washers are properly seated.

proper installation: (cont) Drain hose connection.

Washer won't run

or fill, washer stops

working or wash light

remains on (indicating

that the washer was

unable to fill

appropriately)

Pull drain hose from washer cabinet and properly secure it to

drainpipe or laundry tub.

Do not place tape over drain opening.

Check household plumbing for leaks Water can back up out of a clogged sink or drainpipe. Check all

or clogged sink or drain, household plumbing for leaks (laundry tubs, drain pipe, water

pipes, and faucets.)

Washer not loaded as

recommended.

Check for proper water supply.

Improper loading can cause basket to be out of alignment

and cause water to splash off tub. See "Using Your Washer"

for loading instructions.

Both hoses must be attached and have water flowing to

inlet valve.

Both hot and cold water faucets must be turned on.

Check that inlet valve screens have not become clogged.

Check for any kinks in inlet hoses, which can restrict water flow.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Check proper electrical supply.

Normal washer operation.

Washer may be tightly packed.

Plug power cord into a grounded 3 prong outlet.

Do not use an extension cord.

Ensure there is power to outlet.

Reset a tripped circuit breaker. Replace any blown fuses.

NOTE: If problems continue, contact an electrician.

Lid must be closed for washer to run.

Washer will pause during certain phases of cycle. Do not

interrupt cycle.

Remove several items, rearrange load evenly in basket, and add

detergent. Close lid and press START/Pause.

Do not add more than 1 or 2 additional items after cycle has

started to avoid tightly packing or unbalancing.

TROUBLESHOOTING

Washer not draining/

spinning, loads

are still wet, or spin light

remains on

(indicating that the

washer was unable

to pump out water within

10 minutes)

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

Solution

Empty pockets and use garment bags for small items.Small items may have been caught

in pump or between basket and tub,

which can slow draining.

Use a cycle with a low spin speed.

The washer may be tightly packed or

unbalanced.

Cycles with lower spin speeds remove less water than cycles

with high spin speeds. Use the recommended cycle/spin speed

for your garment. To remove extra water in the load, select Drain

& Spin. Load may need to be rearranged to allow even

distribution of the load in the basket.

Tightly packed or unbalanced loads may not allow the washer

to spin correctly, leaving the load wetter than normal. Evenly

arrange the wet load for balanced spinning. Select the Drain &

Spin cycle to remove excess water. See "Using Your Washer" for

loading recommendations.

Check plumbing for correct drain Check drain hose for proper installation. Use drain hose form

hose installation. Drain hose and securely attach to drainpipe or tub. Do not tape over drain

extends into standpipe farther opening. Lower drain hose if the end is higher than 96" (2.4 m)

than 4.5" (114 mm). above the floor. Remove any clogs from drain hose.

Too much detergent causing suds to Always measure and follow detergent directions for your load. To

slow or stop draining and spinning, remove extra suds, select Rinse & Spin. Do not add detergent.

Dry spots on load High speed spins extract more The high spin speeds combined with air flow during the final

after cycle moisture than traditional top-load spin can cause items near the top of the load to develop dry

washers, spots during the final spin. This is normal.

Check for proper water supply. Make sure hot and cold inlet hoses are not reversed.Incorrect or wrong

wash or rinse

temperatures

Energy saving controlled

wash temperatures.

Load not rinsed Check for proper water supply.

Using too much detergent.

Washer not loaded as recommended.

Both hoses must be attached to both washer and faucet, and

have both hot and cold water flowing to inlet valve.

Check that inlet valve screens are not clogged.

Remove any kinks in hoses.

This washer uses cooler wash and rinse water temperatures than

your previous washer. This includes cooler hot and warm washes.

Make sure hot and cold inlet hoses are not reversed.

Both hoses must be attached and have water flowing to the

inlet valve.

Both hot and cold water faucets must be on.

Using too low a load size/water level

selection.

Sand, pet hair, lint, Heavy sand, pet hair, lint, and Add 2 Rinses to the selected cycle.

etc. on load after detergent or bleach residues may

washing require additional rinsing.

Load is tangling Washer not loaded as recommended.

Inlet valve screens on washer may be clogged.

Remove any kinks in the inlet hose.

The suds from too much detergent can keep washer from

operating correctly. Always measure detergent and follow

detergent directions based on load size and soil level.

The washer is less efficient at rinsing when load is tightly packed.

Load garments in loose heaps evenly around the basket wall.

Load with dry items only.

Use cycle designed for the fabrics being washed.

Add only 1 or 2 additional garments after washer has started.

Choose a load size (water level) that matches the load being

washed.

See "Using Your Washer" section.

Select a cycle with a slower wash action and spin speed; however,

items will be wetter than those using a higher speed spin. See the

"Cycle Guide" to match your load with the best cycle.

Load garments in loose heaps evenly around the basket wall.

Reduce tangling by mixing types of load items. Use the

recommended cycle for the type of garments being washed.

TROUBLESHOOTING

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

If you experience | Possible Causes _ Solution

J i

Not cleaning or

removing stains

Washer not loaded as recommended.

Adding detergent on top of load.

Using too low a load size/water

level selection.

Using too much detergent.

Not using correct cycle for fabric

type.

Not using dispensers.

Not washing like colors together.

Incorrect dispenser Clogged dispenser.

operation

Fabric damage Sharp items were in pockets during

wash cycle.

Strings and straps could have tangled.

Items may have been damaged

before washing.

Fabric damage can occur if load is

tightly packed.

Liquid chlorine bleach may have

been added incorrectly.

Garment care instructions may not

have been followed.

Odors Monthly maintenance not done as

recommended.

Using too much detergent.

Washer is less efficient at cleaning when load is tightly packed.

Load garments in loose heaps evenly around the basket wall.

Load with dry items only.

Add only 1 or 2 additional garments after washer has started.

Add detergent, oxi products, and color-safe bleach to the

bottom of the basket before adding the load items.

Choose a load size (water level) that matches the load being

washed.

The suds from too much detergent can keep washer from

operating correctly. Always measure detergent and follow

manufacturer's directions based on load size and soil level.

Use a higher soil level cycle option and warmer wash

temperature to improve cleaning.

Use Normal Heavy cycle for tough cleaning. See the "Cycle

Guide" to match your load with the best cycle.

Use dispensers to avoid chlorine bleach and fabric softener staining.

Load dispensers before starting a cycle. Select 1 Rinse with

Softener or 2 Rinses with Softener when using fabric softener.

Do not add products directly onto load.

Wash like colors together and remove promptly after the cycle

is complete to avoid dye transfer.

Use only liquid chlorine bleach in the bleach dispenser. Use only

fabric softener in the fabric softener dispenser.

Empty pockets, zip zippers, and snap or hook fasteners before

washing to avoid snags and tears.

Tie all strings and straps before starting wash load.

Mend rips and broken threads in seams before washing.

Load garments in loose heaps evenly around the basket wall.

Load with dry items only.

Use cycle designed for the fabrics being washed.

Add only 1 or 2 additional garments after washer has started.

Do not pour liquid chlorine bleach directly onto load. Wipe up

bleach spills.

Undiluted bleach will damage fabrics. Do not use more than

recommended by manufacturer.

Do not place load items on top of bleach dispenser when

loading and unloading washer.

Always read and follow garment manufacturer's care label

instructions. See the "Cycle Guide" to match your load with

the best cycle.

See "Washer Care" in Washer Maintenance.

Unload washer as soon as cycle is complete.

Be sure to measure correctly. Always follow the manufacturer's

directions.

See "Washer Care" section.

Lid locked light is The lid is not closed. Close the lid. The washer will not start or fill with the lid open.

flashing A cycle was stopped or paused The washer may still be spinning. The lid will not unlock until the

using the START/Pause button, basket has stopped spinning. This may take several minutes if

washing large loads or heavy fabrics.

Single-dose laundry Adding laundry packet incorrectly. Be sure laundry packet is added to washer basket before

packet not dissolving adding clothes. Do not add packet to dispenser. Follow the

manufacturer's instructions to avoid damage to your garments.

WHIRLPOOL CORPORATION LAUNDRY WARRANTY

LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is installed, operated, and maintained according to instructions

attached to or furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter "Whirlpool") will pay for Factory

Specified Replacement Parts and repair labor to correct defects in materials or workmanship that existed when this major appliance

was purchased.

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

Service must be provided by a Whirlpool designated service company. This limited warranty is valid only in the United States or

Canada and applies only when the major appliance is used in the country in which it was purchased. This limited warranty is effective

from the date of original consumer purchase. Proof of original purchase date is required to obtain service under this limited warranty.

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is

used in a manner that is inconsistent to published user or operator instructions and/or installation instructions.

2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or

repair house fuses, or to correct house wiring or plumbing.

3. Service calls to repair or replace appliance light bulbs, air filters, or water filters. Consumable parts are excluded from warranty

coverage.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.

5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage

results from defects in materials or workmanship and is reported to Whirlpool within 30 days from the date of purchase.

6. Pick up and delivery. This major appliance is intended to be repaired in your home.

7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized Whirlpool servicer is not available.

9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance

with Whirlpool published installation instructions.

10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered, or

cannot be easily determined.

The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABiLiTY OR IMPLIED WARRANTY OF FITNESS

FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and

provinces do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply

to you. This warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to

province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Whirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the

representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes

with this major appliance, you should ask Whirlpool or your retailer about buying an extended warranty.

LIMiTATiON OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LiMiTED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

WHIRLPOOL SHALL NOT BE LIABLE FOR iNCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow

the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This

warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

If outside the 50 United States and Canada, contact your authorized Whirlpool dealer to determine if another warranty applies.

If you think you need repair service, first see the "Troubleshooting" section of the Use & Care Guide. If you are unable to resolve

the problem after checking "Troubleshooting," additional help can be found by checking the "Assistance or Service" section or by

calling Whirlpool. In the U.S.A., call 1-800-253-1301. In Canada, call 1-800-807-6777. 10/11

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in=warranty service.

Write clown the following information about your major appliance

to better help you obtain assistance or service if you ever need

it. You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the product.

Dealer name

Address

Phone number

Model number

Serial number

Purchase date

S] CURIT] DE LA LAVEUSE

Votre s_curit_ et celle des autres est tr_s importante,

Nous donnons de nombreux messages de securit6 importants dans ce manuel et sur votre appareil menager.

Assurez=vous de toujours life tous les messages de securit6 et de vous y conformer.

Voici le symbole d'alerte de s6curit6.

Ce symbole d'alerte de securit6 vous signale les dangers potentiels de deces et de blessures graves

vous et & d'autres.

Tousles messages de securit6 suivront le symbole d'alerte de s6curit6 et le mot "DANGER" ou

"AVERTISSEMENT'. Ces mots signifient :

Risque possible de d_ces ou de blessure grave si

vous ne suivez pas imm6diaternent les instructions,

Risque possible de d_c_s ou de blessure grave

si vous ne suivez pas les instructions.

Tousles messages de s_curit6 vous diront quel est le danger potentiel et vous disent comment r6duire le risque de

blessure et ce qui peut se produire en cas de non-respect des instructions.

IMPORTANTES INSTRUCTIONS DE SECURITI _-

AVERTISSEMENT : Pour r6duire les risques d'incendie, de choc electrique ou de blessures Iorsde I'utilisation de la

laveuse, suivre les precautions fondamentales dont les suivantes :

[] Lire toutes les instructions avant d'utiliser la laveuse.

[] Ne pas laver des articles qui ont et6 nettoyes ou

laves avec de I'essence ou imbibes d'essence,

solvants de nettoyage &sec, ou autres substances

inflammables ou explosives; ces substances

peuvent emettre des vapeurs susceptibles de

s'enflammer ou d'exploser.

[] Ne pas ajouter d'essence, solvant de nettoyage &

sec ou autre produit inflammable ou explosif dans

I'eau de lavage. Ces substances peuvent 6mettre

des vapeurs susceptibles de s'enflammer ou

d'exploser.

[] Dans certaines conditions, de I'hydrogene gazeux

peut se former dans un circuit d'eau chaude qui n'a

pas et6 utilise pendant 2 semaines ou plus. LE GAZ

HYDROGENE EST EXPLOSIBLE. Si le circuit d'eau

chaude n'a pas 6t6 utilise pendant une telle p6riode,

avant d'utiliser la laveuse, ouvrir tousles robinets

d'eau chaude et laisser I'eau s'ecouler pendant

plusieurs minutes par chaque robinet. Ceci

permettra 1'6vacuation de I'hydrogene gazeux

accumul6. Comme ce gaz est inflammable, ne pas

fumer ou utiliser une flamme hue au cours de cette

periode.

[] Ne pas laisser des enfants jouer sur ou &I'interieur de la

laveuse. Bien surveiller les enfants Iorsque la laveuse est

utilisee & proximite d'enfants.

[] Avant de mettre la laveuse au rebut ou hors de service,

enlever la porte ou le couvercle.

[] Ne pas tenter d'atteindre un article & I'interieur de la cuve de

la laveuse Iorsque le tambour, la cuve ou I'agitateur est en

mouvement.

[] Ne pas installer ou remiser cette laveuse & un endroit o_ elle

serait expos6e aux intemperies.

[] Ne pas modifier les organes de commande.

[] Ne pas r6parer ou remplacer un composant quelconque de

la laveuse, ni entreprendre une op6ration de service, si ce

n'est specifiquement recommande darts ce manuel ou dans

un manuel d'instructions de r6parations destine & I'utilisateur;

il est alors essentiel que la personne concern6e comprenne

ces instructions et soit competente pour les ex6cuter.

[] Pour les instructions de liaison & la terre, voir "Specifications

electriques" dans les instructions d'installation.

CONSERVEZ CES INSTRUCTIONS

Avertissements de la proposition 65 de I'(=tat de Californie :

AVERTISSEMENT : Ce produit contient au moins un produit chimique connu par I'Etat de Californie pour 6tre & I'origine de

cancers.

AVERTISSEMENT : Ce produit contient au moins un produit chimique connu par I't'=tat de Californie pour 6tre b,I'origine de

malformations et autres d6ficiences de naissance.

QUOI DE NEUF SOUS LE COUVERCLE?

Votre nouvelle laveuse fonctionne differemment de votre prec6dente laveuse de type agitateur.

Verrouillage du couvercle _llJ Bruits

Pour un essorage h plus haute vitesse, le couvercle

se verrouille et le temoin de verrouillage du

couvercle s'allume. Lorsque ce temoin lumineux

s'allume, cela signifie que le couvercle est verrouille

et ne peut _tre ouvert. Lorsque ce temoin lumineux

clignote, cela signifie que la laveuse effectue une

pause. Lorsque ce temoin lumineux est eteint,

cela signifie qu'on peut ouvrir le couvercle. Apres

le demarrage d'un programme, de I'eau penetre

dans la laveuse et celle-ci se verrouille. Si I'on dolt

ouvrir le couvercle pour ajouter un v_tement apres

cette etape, il faut appuyer sur START/Pause (mise

en marche/pause) puis attendre que le couvercle

se deverrouille.Le couverclese deverrouille

uniquementune foisque lemouvement de la

laveusea cesse.Selon lemoment oO I'onsouhaite

suspendreleprogramme, lecouverclepeutmettre

entre plusieurs secondes et plusieurs minutes a se _::-)k

deverrouiller. Appuyer sur START/Pause (mise en

marche/pause).

D_tection

La laveuse effectue une serie d'essorages pour

contr61er I'equilibre de la charge. Durant cette

periode, une serie de cliquetis et un bruit de

frottements rythmiques indiquent que la

technologie de detection determine si la charge

est des6quilibr6e.

Au cours de differents stades du programme

de lavage, vous entendrez peut-_tre des bruits et

pauses que votre laveuse prec6dente ne produisait

pas. Differents bourdonnements et bruits de

frottements rythmiques se produiront a mesure que

I'agitateur evalue I'equilibre de la charge et qu'il la

deplace. II est aussi possible que la laveuse soit

patrols completement silencieuse, Iorsqu'elle laisse

tremper les v_tements.

Ringage par vaporisation

Certains programmes utilisent I'option Rin(;age

par vaporisation par defaut. Au cours de ces

programmes, on entend I'eau pen6trer dans la

laveuse tandis que la cuve tourne, ce qui permet

I'eau de ringage de p6netrer les v@ements.

Consulter le "Guide de programmes" pour plus

de details.

IMPORTANT :

• Apres que le panier de la laveuse se soit rempli jusqu'au niveau d'eau selectionn6, le couvercle doit _tre rabattu

pour que le programme de lavage puisse commencer. Si le remplissage s'arr_te alors que le couvercle est ouvert,

fermer le couvercle et appuyer sur le bouton START (mise en marche).

L'option de ringage doit _tre s61ectionnee sur 1 Rinse with Softener (ringage unique avec assouplissant) ou 2 Rinses

with Softener (double ringage avec assouplissant) pour que I'assouplissant pour tissu soit distribue au moment

adequat.

TABLEAU DE COMMANDE ET CARACTERISTIQUES

Certains programmes et options ne sont pas disponibles sur certains modeles.

Uapparence des appareils peut varier.

LOAD SiZE (TAILLE DE LA CHARGE)

S61ectionner le r6glage leplus adapt6 a votre charge.

Small (petite) ajoute une faible quantit6 d'eau pour les charges

plus petites et Ex Large (tr_s grande) ajoute la quantit6 d'eau

la plus importante pour les grandes charges ou les charges

volumineuses. Les articles doivent pouvoir se

d6placer librement. Trop tasser le linge peut entraTner

une mauvaise performance de lavage et augmenter le

froissement et I'emm_lement.

O WASH TEMP (temperature de

lavage)

La fonction WASH TEMP (temp6rature de lavage) d6tecte et

maintient une temp6rature uniforme de I'eau en r6gulant le

d6bit d'arriv6e d'eau chaude et d'eau froide.

S61ectionner une temp6rature de lavage en fonction du type

1 RINSE with SOFTENER (ringage unique avec

assouplissant)

Cette option dolt _tres61ectionn6esi I'onutilise de

rassouplissant pour tissu durant un programme.Ceci

garantit que I'assouplissantpour tissu est ajout6au bon

moment lots durin£:agepouretre correctement distribu&

2 RINSES with SOFTENER (double ringage avec

assouplissant)

Cette option active lesoptions FabricSoftener

(assouplissantpour tissu)et 2 Rinses(double ringage).

BOUTON START/PAUSE

(rnise en rnarche/pause)

Appuyer sur ce bouton pour d6marrer le programme

de tissu et de salet6 a laver. Pour des r6sultats optimaux,

suivre les instructions sur 1'6tiquette du v_tement et utiliser la

temp6rature d'eau de lavage la plus chaude possible qui reste

sans danger pour le tissu.

. Sur certains modeles et pour certains programmes, les

temp6ratures utilis6es pour I'eau chaude et I'eau tiede

peuvent _tre inf6rieures aux temp6ratures utilis6es par votre

pr6c6dente laveuse.

. M_me pour les lavages dont la temp6rature a 6t6 r6gl6e sur

Cool (frais) ou Cold (froid), il est possible que de I'eau tiede

soit ajout6e a la laveuse pour maintenir une temp6rature

minimale.

BOUTON DE PROGRAMME DE LAVAGE

Utiliser le bouton du programme de lavage pour s61ectionner

les programmes disponibles sur la laveuse. Le bouton reste

statique pendant la progression du programme - voir les

t6moins lumineux de programme pour suivre sa progression

6tape par 6tape. Voir "Guide de programmes" pour des

descriptions de programmes d6taill6es.

s61ectionn6, puis appuyer de nouveau pour suspendre

le programme et d6verrouiller le couvercle. Appuyer

pendant 3 secondes pour annulet un programme.

REMARQUI= : Si la laveuse tourne, le couvercle peut

mettre quelques minutes a se d6verrouiller.

CYCLE STATUS LIGHTS iNDiCATOR

(TI_MOINS LUMINEUX DES PROGRAMMES)

P_og_ess0 0 O (ZD CD CC)

Fill Wash Rinse Spin Done Locked

Les t6moins lumineux indiquent la progression du

programme. A chaque 6tape du processus, il est possible

que I'on remarque des pauses ou des sons diff6rents de

ceux des laveuses ordinaires.

FiLL (rempffssage)

Lorsqu'on appuie sur le bouton START/Pause/Unlock (mise

en marche/pause/d6verrouillage), la laveuse se remplit

jusqu'au niveau d'eau s61ectionn6. Si le couvercle est

ferm6 Iorsque la machine a fini de se remplir, le couvercle

se verrouille et la machine commence afonctionner.

RINSE OPTIONS (options de rin£age)

II est possible d'ajouter les options suivantes A la plupart

des programmes. Voir "Guide de programmes" pour plus de

d6tails.

1 RINSE (ringage unique)

Cette option permet de limiter le nombre de rin(_ages d'un

programme a un seul rin(_age.

2 RINSES (double tin,age)

On peut utiliser cette option pour ajouter automatiquement

un second ringage a la plupart des programmes.

Si le couvercle est ouvert alors que I'eau cesse d'entrer

dans la machine, le programme ne d6marre pas tant

que I'on n'a pas ferm6 le couvercle et que I'on n'a pas

appuy6 sur le bouton START/Pause/Unlock (mise en

marche/pause/d6verrouillage). Si le programme n'a pas

commenc6 dans les 10 minutes qui suivent le remplissage

de la laveuse, la laveuse commence a pomper I'eau pour

1'6vacuer.

REMARQUE : Eviter d'ouvrir le couvercle durant le

processus de d6tection. Le processus de remplissage

recommencera une fois la laveuse remise en marche. Le

t6moin de FILL (remplissage) s'allume 6galement Iors des

6tapes de trempage et de lavage du programme. Ceci

est normal. Pour remettre la laveuse en marche apr_s que

le couvercle a 6t6 ouvert, appuyer sur START (mise en

marche).

WASH(LAVAGE)

Onentend I'impulseur d6placer la charge. Les

bruits 6mis par le moteur peuvent changer lots des

diff@entes 6tapes du programme. La dur6e de lavage

est d6termin6e par le niveau de salet6 s61ectionn6.

RINSE (RIN(_AGE)

On entend des sons similaires b ceux entendu Iors

du programme de lavage b mesure que la laveuse

rince et d6place la charge. On peut entendre le

moteur se mettre en marche brievement (court

bourdonnement) pour faire bouger le panier Iors du

remplissage. Uassouplissant pour tissu sera ajout6 si

I'option 1 Rinse with Fabric Softener (ringage unique

avec assouplissant pour tissu) ou 2 Rinses with

Softener (double ringage avec assouplissant) a 6t6

s61ectionn6e.

Certains programmes utilisent un ringage avec

vaporisation. Apres avoir effectu6 la vidange et

I'extraction de I'eau, la laveuse poursuit I'essorage

et la vaporisation d'eau de ringage pendant toute

la dur6e de ringage.

SPIN (ESSORAGE)

La laveuse essore la charge b des vitesses augmentant

graduellement pour une bonne extraction de I'eau, en

fonction du programme et de la vitesse d'essorage

s61ectionn6s.

DONE (TERMINE)

Une fois le programme terrain6, ce t6moin s'allume.

Retirer la charge rapidement pour un r6sultat optimal.

LID LOCK (VERROUILLAGE

DU COUVERCLE)

Pour un essorage a plus haute

vitesse, le couvercle se verrouille et

le t6moin de verrouillage du couvercle

s'allume. Lorsque ce t6moin lumineux

s'allume, cela signifie que le couvercle

est verrouill6 et ne peut _tre ouvert.

Lorsque ce t6moin lumineux clignote,

cela signifie que la laveuse effectue

une pause. Lorsque ce t6moin lumineux

est 6teint, cela signifie qu'on peut ouvrir

le couvercle.

Si I'on doit ouvrir le couvercle, appuyer

sur START/Pause (mise en marche/

pause). Le couvercle se d6verrouille

une fois que le mouvement de la

laveuse a cess6. II se peut que cela

prenne plusieurs minutes si la laveuse

essorait la charge & grande vitesse.

Appuyer de nouveau sur START/Pause (mise en

marche/pause) pour poursuivre le programme.

CC)

Locked

GUIDE DE PROGRAMMES

Pour un meilleur soin des tissus, choisir le programme qui convient le mieux & la charge & laver.

Certains programmes et options ne sont pas disponibles sur certains modeles.

Articles en coton,

linge de maison et

charges mixtes

Articles en coton,

linge de maison et

charges mixtes

Articles en coton,

linge de maison et

charges mixtes

Articles non

repassables,

articles en coton,

de pressage

permanent, linge

de maison, tissus

synth6tiques

Articles non

repassables,

articles en coton,

de pressage

permanent,

linge de maison,

tissus

synth6tiques

Articles en soie

lavables en

machine, articles

lav6s & la main

Maillots et articles

n6cessitant un

ringage sans

d6tergent

Articles tres

humides

et articles lav6s &

la main

Pas de v_tements

dans

la laveuse

Normal (normal)

Light (16ger)

Normal (normal)

Regular

(r6gulier)

Normal (normal)

Heavy (intense)

Casual

(Tout-aller)

Regular

(r6gulier)

Casual

(Tout-aller)

Light (16ger)

Delicate

(Articles

d61icat)

Rinse & Spin

(Ringage et

essorage)

Drain & Spin

Gqdange

et essorage)

Clean Washer

with affresh®

(nettoyage de

la laveuse avec

affresh®)

Hot (Chaude)

Warm (Tiede)

Cool (Fraiche)

Cold (Froide)

Tap Cold (froide

du robinet)

Hot (Chaude)

Warm (Tiede)

Cool (Fraiche)

Cold (Froide)

Tap Cold (froide

du robinet)

Hot (Chaude)

Warm (Tiede)

Cool (Fraiche)

Cold (Froide)

Tap Cold (froide

du robinet)

Hot (Chaude)

Warm (Tiede)

Cool (Fraiche)

Cold (Froide)

Tap Cold (froide

du robinet)

Hot (Chaude)

Warm (Tiede)

Cool (Fraiche)

Cold (Froide)

Tap Cold (froide

du robinet)

Hot (Chaude)

Warm (Tiede)

Cool (Fraiche)

Cold (Froide)

Tap Cold (froide

du robinet)

Ringage h

I'eau froide

uniquement

N/A

Hot (Chaude)

Warm (Tiede)

Cool (Fraiche)

Cold (Froide)

Tap Cold (froide

du robinet)

.High

(Elev6e)

.High

(Elev6e)

.High

(Elev6e)

Low

(Basse)

Low

(Basse)

Low

(Basse)

.High

(Elev6e)

.High

(Elev6e)

Low

(faible)

Utiliser ce programme pour laver des charges mixtes

de v_tements peu sales. Ce programme comporte un

ringage par vaporisation.

Utiliser ce programme pour les articles en coton et

les charges de tissus mixtes pr6sentant un degr6 de

salet6 normal. Ce programme comporte un ringage

par vaporisation.

Utiliser ce programme pour les articles tres sales ou

robustes. Ce programme comporte un ringage par

vaporisation. Utiliser ce programme pour nettoyer

I'int@ieur de la laveuse. Voir "Entretien de la laveuse".

Utiliser ce programme pour laver des charges de

v6tements qui ne se repassent pastels que chemises

de sport, chemisiers, v_tements de travail tout-aller,

articles & pressage permanent et m61anges de tissus.

Utiliser ce programme pour laver des charges peu sales

de v6tements non repassables tels que chemises de

sport, chemisiers, v_tements de travail tout-aller, articles

& pressage permanent et m61anges de tissus.

Utiliser ce programme pour laver des v_tements

16gerement sales dont 1'6tiquette de soin indique "Soie

lavable en machine" ou "Programme d61icat". Placer les

petits articles dans des sacs en filet avant le lavage. Ce

programme comporte un ringage par vaporisation.

Combine un ringage et un essorage rapide pour

les charges n6cessitant un programme de ringage

suppl6mentaire ou pour finir de prendre soin d'une

charge apres une coupure de courant. Utiliser

6galement pour les charges n6cessitant uniquement

un ringage.

Ce programme utilise un essorage pour r6duire les

dur6es de s6chage pour les tissus Iourds et les articles

lav6s a la main n6cessitant un soin sp6cial. Utiliser ce

programme pour vidanger la laveuse apres avoir annul6

un programme ou avoir termin6 un programme apres

une coupure de courant.

Utiliser ce programme &I'issue de chaque s@iede 30

lavages pour que I'int@ieur de la laveuse reste frais et

propre. Ce programme utilise un niveau d'eau plus elev&

Avec ce programme, utiliser une tablette de nettoyant

pour laveuse affresh ®ou de I'eau de Javel pour nettoyer

soigneusement I'int@ieur de votre laveuse. Ce programme

ne dolt pas _tre interrompu. Voir "Entretien de la laveuse".

IMPORTANT : Ne pas placer de v_tements ou autres

articles dans la laveuse pendant le programme Clean

Washer with affresh®.Utiliser ce programme avec une cuve

de lavage vide.

REMARQUE • Si I'on utilise de I'assouplissant pour tissu, veiller & s61ectionner I'option 1 Rinse with Softener (ringage unique avec

assouplissant) ou 2 Rinses with Softener (double ringage avec assouplissant).

*Tous les ringages se font & I'eau froide.

UTILISATION DE LALAVEUSE

Risque d'incendie

Ne jamais mettre des articles humect_s d'essence ou

d'autres fluides inflarnrnables darts la laveuse.

Aucune laveuse ne peut compl_tement enlever I'huile.

Ne pas faire s_cher des articles qui ont _t_ sails par

tout genre d'huile (y compris les huiles de cuisson).

Le non-respect de ces instructions peut causer un

d_c_s, une e×plosion ou un incendie.

Risque de choc _lectrique

Brancher sur une prise & 3 alv_oles reli_e & la terre.

Ne pas enlever la broche de liaison _ la terre.

Ne pas utiliser un adaptateur.

Ne pas utiliser un c&ble de rallonge.

Le non=respect de ces instructions peut causer

un d_c_s, un incendie ou un choc _lectrique.

* Vider les poches. Des pieces de monnaie, des boutons

ou objets de petite taille sont susceptibles de glisser sous

I'impulseur et de s'y coincer, ce qui peut entraTne des bruits

inattendus.

= Trier les articles en fonction du programme et de

la temp6rature d'eau recommand6s, ainsi que de

la solidit6 des teintures.

= S6parer les articles tr_s sales des articles peu sales.

= S6parer les articles d61icats des tissus r6sistants.

= Ne pas s6cher les v_tements si les taches sont toujours

pr6sentes apr_s le lavage car la chaleur pourrait fixer

les taches sur le tissu.

* Traiter les taches sans d61ai.

= Fermer les fermetures & glissiere, attacher les crochets,

cordons et ceintures en tissu. Oter les garnitures et les

ornements non lavables.

= R6parer les d6chirures pour 6viter que les articles

ne s'endommagent encore davantage lots du lavage.

Conseils utiles :

* Lots du lavage d'articles imperm_ables ou r6sistants

I'eau, charger la machine de fagon uniforme.

= Utiliser des sacs en filet pour aider a emp_cher I'emm_lement

lots du lavage d'articles d61icats ou de petits articles.

,, Retourner les tricots pour 6viter le boulochage. S6parer

les articles qui forment la charpie de ceux qui la retiennent.

Les articles synth6tiques, tricots et articles en velours

retiennent la charpie provenant des serviettes, des tapis

et des tissus chenille.

REMARQUE : Toujours life et suivre les instructions des

etiquettes de soin des tissus pour 6viter d'endommager

les v_tements.

Ajouter les produits de lessive

Verser une mesure de d6tergent ou un sachet de lessive

dose unique dans le panier.

Si I'on utilise des produits activateurs de d6tergent de type

Oxi, un agent de blanchiment sans danger pour les couleurs

ou de I'assouplissant pour tissu sous forme de cristaux, les

ajouter au fond du panier de la laveuse avant d'ajouter les

v_tements.

REMARQUE : Suivre les instructions du fabricant pour

d6terminer la quantit6 de produits de lessive a utiliser.

La page charge ...

Whirlpool 7MWTW1604DM0 Le manuel du propriétaire

Marque: Whirlpool

Modèle: 7MWTW1604DM0

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool 7MWTW1604DM0 Owner's manual

Whirlpool 7MWTW1604DM0 Le manuel du propriétaire

Ce manuel convient également à

Whirlpool 7MWTW1604DM0 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents