ENGLISH
FRANÇAIS
INSTALLATION MANUAL
GAS RANGE
Please read these instructions thoroughly before
installing and operating the range.
Models
LRG3097ST
LRG3095ST/SB/SW
LRG3093ST/SB/SW
LRG3085ST
LRG3081ST
moc.gl.www
MFL63640001 (REV.07 140616)
Owner's Manual
INSTALLATION I NSTRU C TIONS
INSTALLATION SAFETY INSTRUCTIONS
BEFORE YOU BEGIN
Remove all tape and packing materials before using the range. Dispose of all plastic bags after
unpacking the range. Never allow children to play with packing materials.
IMPORTANT SAFETY INSTRUCTIONS
Read these instructions completely and carefully. Improper installation, adjustment, alteration, service
or maintenance can cause injury or property damage. Refer to this manual. For assistance or
additional information, consult a qualified installer, service agency, manufacturer (dealer) or the gas
supplier.
This symbol will alert you to hazards or unsafe practices which could
cause serious bodily harm or death.
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or
hurt you and others. All safety messages will follow the safety alert symbol and either the
word “WARNING” or “CAUTION”.
This symbol will alert you to hazards or unsafe practices which could
cause bodily injury or property damage.
WARNING
CAUTION
READ ALL INSTRUCTIONS BEFORE INSTALLATION
WHAT TO DO IF YOU SMELL GAS
•
DO NOT
try to light any appliance.
•
DO NOT
touch any electrical switch.
•
DO NOT
use any phone in your building.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier, call the
fire department.
– DO NOT store or use combustible materials,
gasoline or other flammable vapors and liquids in
the vicinity of this or any other appliance.
Installation and service must be performed by a
qualified installer, service agency or the gas
supplier
WARNING:
If the information in
this manual is not followed exactly, a fire or
explosion may result causing property damage,
personal injury or death.
HSILGNE
ENGLISH
I NSTALLATION I NSTRUCTIONS
• NEVER reuse old flexible connectors. The use of
old flexible connectors can cause gas leaks and
personal injury. Always use NEW flexible
connectors when installing a gas appliance
.
• Your range must be installed by a qualified
installer.
• Your range should be electrically grounded in
accordance with local codes or, in the absence of
local codes, in accordance with the National
Electrical Code (ANSI/NFPA 70, latest edition). In
Canada, electrical grounding must comply with
the current CSA C22.1 Canadian Electrical Code
Part 1 and/or local codes. See “ELECTRICAL
CONNECTIONS” in this manual.
• Before installing your range on linoleum or any
other synthetic floor covering, make sure the floor
covering can resist 180°F(82°C) without shrinking,
warping or discoloring. Do not install the range
over carpeting unless a sheet of 1/4” thick
plywood or similar insulator is placed between the
range and carpeting.
• Make sure the wall coverings around the range
can resist heat generated by the range up to
180°F(93°C).
• Leak testing of the appliance shall be conducted
according to the manufacturer’s instructions.
• Avoid placing cabinets above the range. To
minimize the hazard caused by reaching over the
open flames of operating burners, install a
ventilation hood over the range that projects
forward at least 5” beyond the front of the
cabinets.
• The ventilation hood must be constructed of sheet
metal not less than 0.0122” thick. Install above
the cooktop with a clearance of not less than 1/4”
between the hood and the underside of the
combustible material or metal cabinet.
The hood must be at least as wide as the
appliance and centered over the appliance.
Clearance between the cooking surface and
the ventilation hood surface MUST NEVER BE
LESS THAN 24 INCHES.
EXCEPTION: Installation of a listed microwave
oven or cooking appliance over the cooktop shall
conform to the installation instructions packed with
that appliance.
• If cabinets are placed above the range, allow a
minimum clearance of 30
”
between the cooking
surface and the bottom of unprotected cabinets.
INSTALLATION SAFETY INSTRUCTIONS
(continued)
READ ALL INSTRUCTIONS BEFORE INSTALLATION
WARNING
• DO NOT step or sit on the door. Install the
Anti-Tip Bracket packed with the range.
- The range could be tipped and injury might result
from spilled hot liquid, food, or the range itself.
- If the range is pulled away from the wall for
cleaning, service, or any other reason, ensure that
the Anti-Tip Device is properly reengaged when
the range is pushed back against the wall.
All ranges can tip and injury could result. To prevent
accidental tipping of the range, attach an approved
Anti-Tip device to the wall. (See “INSTALLING THE
ANTI-TIP DEVICE” in this manual.) To check if the
device is installed and engaged properly, carefully
tip the range forward. The Anti-Tip device should
engage and prevent the range from tipping over.
If you pull the range out from the wall for any
reason, make sure the Anti-Tip device is engaged
when you push the range back against the wall.
WARNING!
• ALL RANGES CAN TIP
• INJURY TO PERSONS
COULD RESULT
• INSTALL ANTI-TIP DEVICES
PACKED WITH RANGE
• SEE INSTALLATION
INSTALLATION INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE INSTALLATION
PREPARING FOR INSTALLATION
TOOLS YOU WILL NEED MATERIALS YOU MAY NEED
• Gas line shut-off valve
• Pipe joint sealant that resists action of natural and
LP gases.
• Flexible metal appliance connector (3/4” or 1/2” NPT
x 1/2” I.D.)
Never use an old connector when installing a new
range.
• Flare union adapter for connection to gas supply line
(3/4” or 1/2” NPT x 1/2” I.D.)
• Flare union adapter for connection to pressure
regulator on range (1/2” NPT x 1/2” I.D.)
• Liquid leak detector or soapy water.
• Lag bolt or 1/2” O.D. sleeve anchor (for concrete
floors only).
IN THE COMMONWEALTH OF MASSACHUSETTS
• This product must be installed by a licensed
plumber or gas fitter.
• When using ball type gas shut-off valves, they shall
be the T-handle type.
• When using a flexible gas connector, it must not
exceed 3 feet in length.
Phillips screwdriver
Flat-blade screwdriver
Pencil and ruler
Pipe wrench(2)
(one for support)
Open-end or
adjustable wrench
Level
INSTALLATION SAFETY INSTRUCTIONS (continued)
• Items of interest to children should not be stored in
cabinets above a range or on the backsplash of a
range—children climbing on the range to reach
items could be seriously injured.
• DO NOT attempt to operate the oven of this range
during a power failure.
CAUTION
WARNING
• If a 30” clearance between cooking surface and
overhead combustible material or metal cabinets
cannot be maintained, protect the underside of the
cabinets above the cooktop with not less than 1/4”
insulating millboard covered with sheet metal not
less than 0.0122” thick. Clearance between the
cooking surface and protected cabinets MUST
NEVER BE LESS THAN 24 INCHES.
• The vertical distance from the plane of the cooking
surface to the bottom of adjacent overhead
cabinets extending closer than 1” to the plane of
the range sides must not be less than 18”. (See
the Dimensions and Clearances illustration in this
manual.)
ENGLISH
ENGLISH
INSTALLATION INSTRUCTIONS
ENGLISH
DIMENSIONS AND CLEARANCES
Provide proper clearances between the range and
adjacent combustible surfaces. These dimensions
must be met for safe use of your range. The location
of the electrical outlet and pipe opening (see “GAS
PIPE AND ELECTRICAL OUTLET LOCATIONS”)
may be adjusted to meet specific requirements.
The range may be placed with 0” clearance (flush) at
the back wall.
INSTALLATION
CLEARANCES
Minimum to
cabinets on
either side of
the range
18”
5”
30”
30”
5”
36”
1/4”
13”
0”
DIMENSIONS
Height
Depth with door open.
Depth with door closed (includes door handle)
Minimum
clearance
to left wall
Minimum clearance to
right wall
Front edge of
the range side
panel forward
from cabinet
To cabinets
below cooktop
and at the range
back
Maximum depth
for cabinets
above
coutertops
Minimum
30”
28
3
/
4
”
47
7
/
16
”
47
1
/
4
”
36” ± 1/4”
I N S TA L L AT ION INST RU CTION S
LOCATION
Do not locate your range where it may be subject
to strong drafts. Any openings in the floor or wall
behind the range should be sealed. Make sure the
openings around the base of the range that
supply fresh air for combustion and ventilation
are not blocked by carpeting or woodwork.
Your range, like many other household units, is heavy
and can be installed on soft floor coverings such as
cushioned vinyl or carpeting. Use care when moving
the range on this type of flooring.
It is recommended that the following simple and
inexpensive instructions be followed to protect your
floor.
When the floor covering ends at the front of the range
the area that the range will be installed on should be
built up with plywood to the same level or higher than
the floor covering. This will allow the range to be
moved for cleaning and servicing, as well as proper
air flow to the range.
Also, make sure the wall covering can resist 180°F
(82°C). See the "INSTALLATION SAFETY
INSTRUCTIONS" (included in this manual).
Make sure the wall coverings around your range can
resist the heat generated (up to 200°F/93°C) by the
range. See the "INSTALLATION SAFETY
INSTRUCTIONS" (included in this manual).
This appliance must not be installed with a ventilation
system that blows air downward toward the range.
This type of ventilation system may cause ignition and
combustion problems with the gas cooking appliance
resulting in personal injury or unintended operation.
ENGLISH
INSTALLATION INSTRUCTIONS
ENGLISH
GAS PIPE AND ELECTRICAL OUTLET LOCATIONS
1. PROVIDE ADEQUATE GAS SUPPLY
Your range is designed to operate at a pressure of
5” of water column on natural gas or 10” of water
column on LP.
Make sure you are supplying your range with the type
of gas for which it is configured.
This range is convertible for use on natural or LP gas.
When using this range on LP gas, conversion must be
made by a qualified LP installer before attempting to
operate the range.
For proper operation, the pressure of natural gas
supplied to the regulator must be between 5” and 13”
of water column.
For LP gas, the pressure supplied to the regulator
must be between 10” and 13” of water column.
When checking for correct operation of the regulator,
the inlet pressure must be at least 1” more than the
operating (manifold) pressure as given above.
The pressure regulator located at the inlet of the
range must remain in the supply line regardless of
which type of gas is being used.
A flexible metal appliance connector used to connect
the range to the gas supply line should have an I.D. of
5/8” and a max of 5ft. In Canada, flexible connectors
must be single wall metal connectors less than 6 feet
in length.
7
INSTALLATION INSTRUCTIONS
FLEXIBLE CONNECTOR HOOKUP
Pressure regulator
Installer: Inform the
consumer of the
location of the gas
shut-off valve.
Adapter
Adapter
Gas shut-off valve
1/2” or 3/4”
Gas pipe
Flex connector
(6 ft. max.)
Gas Flow into Range
2. CONNECT THE RANGE TO GAS
Shut off the range gas supply valve before
removing the old range and leave it off until the
new hook-up has been completed.
Because hard piping restricts movement of the range,
the use of a CSA International-certified flexible metal
appliance connector should be used unless local
codes require a hard-piped connection.
NEVER reuse an old connector when installing a new
range.
To protect against gas leaks, use a qualified pipe joint
sealant on all external threads.
Install male 1/2” or 3/4” flare union adapter to the
NPT internal thread of the manual shut-off valve,
taking care to back-up the shut-off valve to keep it
from turning.
Install male 1/2” flare union adapter to the 1/2”
NPT internal thread at inlet of presure regulator.
Use a backup wrench on the presure regulator
fitting to prevent damage.
Connect flexible metal appliance connector to the
adapter on the range. Position range to permit
connection at the shut-off valve.
When all connections have been made, be sure
all range controls are in the off position and turn
on the main gas supply valve. Check for gas leaks
by using a liquid leak detector at all joints and
connections.
A
C
B
D
DO NOT USE A FLAME TO CHECK FOR GAS
LEAKS.
WARNING!
WARNING!
Isolate the range from the gas supply system by
closing its individual shut-off valve during any
pressure testing of the gas supply system at test
pressures equal to or less than 1/2” psig(3.5kPa).
ENGLISH
ENGLISH
INSTALLATION INSTRUCTIONS
ENGLISH
ELECTRICAL REQUIREMENTS
120 Volt, 60 Hertz, properly grounded dedicated circuit protected by a 15 or 20 Amp circuit breaker, or slow
blow fuse.
GROUNDING
IMPORTANT: FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED.
3. ELECTRICAL CONNECTIONS
The power cord of this appliance is equipped with a
3-prong (grounding) plug which mates with a standard
3-prong grounding wall receptacle to minimize the
possibility of electric shock hazard from this
appliance.
The customer should have the wall receptacle and
circuit checked by a qualified electrician to make sure
the receptacle is properly grounded.
Where a standard two-prong wall receptacle is
encountered, it is the personal responsibility and
obligation of the customer to have it replaced with a
properly grounded three-prong wall receptacle.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR
REMOVE THE THIRD (GROUND) PRONG FROM
THE POWER CORD.
A word about GFCI’s – GFCI’s are not required or
recommended for gas range receptacles.
Ground Fault Circuit Interrupters (GFCI’s) are devices
that sense leakage of current in a circuit and
automatically switch off power when a threshold
leakage level is detected. These devices must be
manually reset by the consumer. The National
Electrical Code requires the use of GFCI’s in kitchen
receptacles installed to serve countertop surfaces.
Performance of the range will not be affected if
operated on a GFCI-protected circuit but occasional
nuisance can occur.
DO NOT use an adapter plug because disconnecting
of the power cord places undue strain on the adapter
and leads to eventual failure of the adapter ground
terminal.
The installation of appliances designed for mobile
home installation must conform with the Manufactured
Home Construction and Safety Standard, Title 24
CFR, Part 3280 (formerly the Federal Standard for
Mobile Home Construction and Safety, Title 24, HUD,
Part 280) or, when such standard is not applicable,
the Standard for Manufactured Home Installations,
latest edition (Manufactured Home Sites,
Communities and Set-Ups), ANSI A225.1, latest
edition, or with local codes. In Canada, mobile home
installation must be in accordance with the current
CAN/CSA Z240/MH Mobile Home Installation Code.
Ensure proper ground
exists before use
PREFERRED
METHOD
4. SEAL THE OPENINGS
Seal any openings in the wall and floor after electrical and gas supplies are completed.
CAUTION:
The customer should have the circuit checked by a
qualified electrician to make sure the receptacle is
properly grounded.
INSTALLATION I N S T RU C TIONS
5. ASSEMBLE THE SURFACE BURNERS
CAUTION
Place the burner caps and heads on the cooktop.
Make sure that the caps and heads are placed in the
correct locations. There is one small, one medium,
one large and one extra large burner head and cap.
Make sure the hole in the burner head is positioned
over the electrode.
6. CHECK IGNITION OF SURFACE BURNERS
ELECTRIC IGNITION
Select a top burner knob and simultaneously push in
and turn to the “LITE” position. You will hear a clicking
sound indicating proper operation of the spark
module.
Once the air has been purged from the supply lines,
the burner should ignite within 4 seconds.
After the burner ignites, rotate the knob out of the
“LITE” position. Try each burner in succession until
all burners have been checked.
QUALITY OF FLAMES
The combustion quality of burner flames needs to be
confirmed visually.
A Yellow flames—Call for service
B Yellow tips on outer cones—
It is normal for LP gas
C Soft blue flames—
It is normal for natural gas
With LP gas, some yellow tipping on outer cones is
normal.
Oval (Center) Burner
Head/Cap Assembly
Medium burner
head and cap
(on some
models)
(on some
models)
Large burner
head and cap
Front of range
Small burner
head and cap
Extra large burner
head and cap
Hole
Electrode
DO NOT operate the burners without all parts in
place.
ENGLISH
ENGLISH
INSTALLAT I ON I N S T RUCTIONS
ENGLISH
7. ADJUST THE SURFACE BURNER LOW
FLAME(SIMMER) SETTING.
1) Light all surface burners.
2) Turn the knob on the burner being adjusted to
“LO”.
3) Remove knob.
4) Insert a small, flat bladed screwdriver into the valve
shaft as shown in Fig. 1.
On right front valve for model LRG3097S there is a
secondary adjustment for the low flame for the
outer burners.
Using a small, flat bladed screwdriver insert into
the hole next to the valve stem to adjust the outer
flame as shown in Fig. 2.
Turn the adjustment screw until the flame reaches
the desired size.
5) Replace the knob.
Note: Hold the valve shaft with one hand while turning
the screw for adjustment with the other.
6) Test The Flame Stability.
Test 1: Turn the knob from “HI” to “LOW” quickly.
If the flame goes out, increase the flame size and test
again.
Test 2: With the burner on a “LOW” setting, open and
close the oven door quickly. If the flame is
extinguished by the air currents created by the door
movement, increase the flame height and test again.
7) Repeat steps 1-5 for each surface burner.
Center adjustment screw
Fig. 1
Adjustment screw next to
the valve shaft
Fig. 2
INSTALLATION INSTRUCTIONS
8. CHECK OPERATION OF BAKE/BROIL BURNERS
To check ignition of the Bake burner follow the steps
below:
1) Remove all packing from inside the oven cavity.
2) Press "Bake" (350 will be shown in the display).
3) Press Start
It may take between 30 and 90 seconds for the burner
to start heating.
To check ignition of the Broil burner follow the steps
below:
1) Press "Broil" ("Hi" will be shown in the display).
2) Make sure the door is closed.
3) Press Start
It may take between 30 and 90 seconds for the burner
to start heating.
NOTE: Do not try and light either the bake or broil
burners during a power outage. The range has an
electrical ignition system and can not be used
without power.
9. AIR SHUTTER ADJUSTMENT FOR BAKE AND BROIL
BURNERS.
The range comes from the factory with air shutters adjusted for proper air flow for natural gas.
If converted to LP follow the instructions provided in the conversion kit to properly adjust the air shutters.
LP conversion must be performed by a qualified technician.
ENGLISH
ENGLISH
ENGLISH
INSTALLAT I ON I N S T RUCTIONS
11. LEVELING THE RANGE
Install the oven shelves in the oven and locate the
range where it will be installed.
Check for levelness by placing a spirit level or a
cup, partially filled with water, on one of the oven
shelves. If using a spirit level, take two readings—
with the level placed diagonally first in one
direction –
and then the other – .
Remove the drawer. See the “CARE AND
CLEANING OF THE RANGE” section in the
User’s Guide. The front leveling legs can be
adjusted from the bottom and the rear legs can be
adjusted from the bottom.
Use an open-end or adjustable wrench to adjust
the leveling legs until the range is level.
Leg leveler
Raise
range
Lower
range
Spirit level
A
C
D
B
10. INSTALLING THE ANTI-TIP DEVICE
An Anti-tip bracket is packaged with a template.
The instructions include the necessary information to
complete the installation.
Read and follow the range installation instruction
sheet (template).
LOCATING THE BRACKET USING THE
TEMPLATE.
WARNING
• Range must be secured with an approved Anti-
Tip device.
• Unless properly installed, the range could be
tipped by you or a child standing, sitting or
leaning on an open door.
• After installing the Anti-Tip device, verify that
it is in place by carefully attempting to tilt the
range forward.
• This range has been designed to meet all
recognized industry tip standards for all
normal conditions.
• The installation of the Anti-Tip device must
meet all local codes for securing the
appliance.
• The use of this device does not preclude
tipping of the range when not properly
installed.
INSTALLATION I NSTRU C TIONS
WHEN ALL HOOKUPS ARE COMPLETE
Make sure all controls are left in the off position. Make sure the flow of air to the range for combustion
and ventilation is unblocked.
CONVERTING TO LP GAS
(OR CONVERTING BACK TO NATURAL GAS FROM LP)
This range leaves the factory set for use with
natural gas. The conversion to LP gas must be
performed by a qualified LP gas installer when
converting to LP gas.
The conversion instructions and LP orifices can be
found attached to the range next to the oven valve.
Keep these instructions and the orifices in case you
want to convert back to natural gas.
ENGLISH
ENGLISH
Memo
FRANÇAIS
P/No.: MFL63640001 www.lg.com
MANUEL D’INSTALLATION
CUISINIÈRE À GAZ
Veuillez lire ce manuel en entier avant l'installation et
l'utilisation de la cuisinière.
Modèles
LRG3097ST
LRG3095ST/SB/SW
LRG3093ST/SB/SW
LRG3085ST
LRG3081ST
2
CONSIGNES D'I NSTALLATION
CONSIGNES DE SÉCURITÉ
LISEZ TOUTES LES CONSIGNES AVANT L’INSTALLATION
AVANT TOUT
Lisez ces directives, en entier et avec
soin.
L’installation de cette cuisinière doit être conforme
aux codes municipaux ou, en l’absence de tels
codes, de la plus récente édition du Code national du
gaz, ANSI Z223.1/NFPA.54. Au Canada, l’installation
doit être conforme au Code courant d’installation
pour le gaz naturel,
CAN/CGA-B149.1, ou au Code
courant d'installation pour le gaz propane,
CAN/CGA-B149.2,
et aux codes municipaux,
le cas échéant. Le design de cette cuisinière a été
certifié par la CSA International, conformément à la
plus récente édition ANSI Z21.1, et la plus récente
édition CAN-CGA-1.1 de l’Association canadienne du gaz.
Comme avec tout appareil utilisant du gaz et
générant de la chaleur, certaines mesures de
précaution doivent être prises. Ces mesures de
précaution se trouvent dans la section sur les
Consignes de sécurité du guide de l’utilisateur. Lisez-
les soigneusement.
– Gardez ces directives à la
disposition de l’inspecteur municipal des services
électriques.
– Observez tous les codes et
tous les règlements en vigueur.
Laissez ces directives
avec l’appareil, une fois l’installation terminée.
Conservez le guide
de l’utilisateur ainsi que les directives d’installation
aux fins de référence ultérieure.
• Le schéma électrique se trouve dans une
enveloppe apposée au dos de la cuisinière.
• Aptitudes – L’installation de cette cuisinière exige
des aptitudes mécaniques de base.
• L’installation appropriée est la responsabilité de
l’installateur.
• Une défaillance de l’appareil découlant d’une
mauvaise installation n’est pas couverte par la
garantie.
• Enlevez tous les rubans et toutes les pièces
d’emballage.
• Assurez-vous que les brûleurs sont bien en place et
de niveau.
• Retirez le paquet d’accessoires du four ou du tiroir.
• Asssurez-vous qu’aucune pièce de la cuisinière
n’est devenue lâche en cours de transport.
CONSI GNES D'I NSTALLAT I O N
CONSIGNES DE SÉCURITÉ
AVANT DE COMMENCER
Retirez tous les matériaux d'emballage et les rubans adhésifs avant d'utiliser la cuisinière. Jetez tous les
sacs en plastique après avoir déballé la cuisinière. Ne laissez jamais des enfants jouer avec les matériaux
d'emballage.
CONSIGNES DE SÉCURITÉ IMPORTANTES
Lisez entièrement et attentivement ces consignes. L'installation, le réglage, la modification, la réparation
ou l'entretien effectués de manière incorrecte peuvent provoquer des blessures ou des dégâts. Reportez-
vous à ce manuel. Pour obtenir de l'aide ou des renseignements supplémentaires, consultez
un installateur agréé, un centre d'assistance, le fabricant (distributeur) ou le fournisseur de gaz.
Ce symbole attire votre attention sur des dangers ou des
pratiques dangereuses qui pourraient provoquer des blessures
graves ou le décès.
Ce symbole d'avertissement de sécurité attire votre attention sur les dangers potentiels qui
peuvent entraîner des blessures ou le décès. Tous les messages de sécurité reprennent ce
symbole d'avertissement ainsi que la mention AVERTISSEMENT ou ATTENTION.
Ce symbole attire votre attention sur des dangers ou des pratiques
dangereuses qui pourraient provoquer des blessures ou des dégâts.
AVERTISSEMENT
ATTENTION
LISEZ TOUTES LES CONSIGNES AVANT L’INSTALLATION
EN CAS D'ODEUR DE GAZ
• N'allumez aucun appareil.
• NE touchez à aucun interrupteur électrique.
• N'utilisez pas votre téléphone à l'intérieur.
• Appelez immédiatement votre fournisseur de gaz
à partir du téléphone d'un voisin.
Suivez les instructions de votre fournisseur de gaz.
• Si vous ne parvenez pas à joindre votre
fournisseur de gaz, appelez les pompiers.
NE stockez pas et n'utilisez pas de matériaux
combustibles, de l'essence ni d'autres gaz et liquides
inflammables à proximité de cette table de cuisson
ou d'autres appareils électroménagers.
L'installation et le dépannage doivent être confiés
à un installateur ou un prestataire de services
qualifié, ou au fournisseur de gaz.
AVERTISSEMENT :
Les
renseignements fournis dans ce manuel doivent être
scrupuleusement respectés afin d'éviter tout incendie
ou explosion qui provoquerait des dégâts,
des blessures ou la mort.
FRANÇAIS
C ONSIGNES D 'INSTALLAT I O N
CONSIGNES DE SÉCURITÉ
(suite)
LISEZ TOUTES LES CONSIGNES AVANT L’INSTALLATION
AVERTISSEMENT
• NE réutilisez jamais d'anciens raccords flexibles.
L'utilisation de raccords flexibles usagés peut provoquer
des fuites de gaz et des blessures. Utilisez toujours des
raccords flexibles NEUFS lors de l'installation d'un
appareil au gaz.
• Faites installer votre cuisinière par un installateur agréé.
• Votre cuisinière doit être mise à la terre conformément
aux normes locales ou, en l'absence de telles normes,
conformément au Code national de l'électricité
(ANSI/NFPA 70, dernière édition).
Au Canada, la mise à la terre doit être conforme au
Code national de l'électricité CSA C22.1, première partie,
en vigueur ou aux normes locales. Voir la section
Branchements électriques de ce manuel.
• Avant d'installer votre cuisinière sur du linoléum ou tout
autre revêtement de sol synthétique, assurez-vous que
ce revêtement peut supporter une température de
180
°F (82 °C) sans rétrécir, se déformer ou se décolorer.
N'installez pas la cuisinière sur de la moquette à moins
qu'une planche de contreplaqué de 6,4 mm (1/4 po)
d'épaisseur ou un isolant similaire n'ait été placé entre la
cuisinière et la moquette.
• Vérifiez que les revêtements des murs autour de la
cuisinière peuvent supporter la chaleur générée par la
cuisinière, qui peut atteindre les 180 °F (82 °C).
• Le test de fuite de l'appareil doit être effectué
conformément aux consignes du fabricant.
• o Évitez de placer des rangements au-dessus de la
cuisinière. Pour limiter le risque de contact avec les
flammes nues des brûleurs en cours de fonctionnement,
installez une hotte de ventilation au-dessus de la
cuisinière dépassant d'au moins 12,7 cm (5 po) à l'avant
des rangements.
• La hotte de ventilation doit
être réalisée en plaques de
métal d'au moins 0,3 mm (0,0122 po) d'épaisseur.
Installez-la au-dessus de la table de cuisson en
prévoyant un espace d'au moins 6,4 mm (1/4 po) entre la
hotte et le dessous du matériau combustible ou du
rangement métallique.
La hotte doit être au moins aussi large que l'appareil et
centrée au-dessus de l'appareil.
L'espace entre la surface de cuisson et la surface de la
hotte de ventilation NE DOIT JAMAIS ÊTRE
INFÉRIEURE À 24" 61 CM (24 PO).
EXCEPTION : l'installation d'un four à micro-ondes ou d'un
appareil de cuisson conforme au-dessus de la table de
cuisson est possible dans le respect des consignes
d'installations livrées avec cet appareil.
• Si des rangements sont placés au-dessus de la
cuisinière, prévoyez un espace d'au moins 76,2 cm (30
po) entre
la surface de cuisson et le dessous des
rangements non protégés.
• NE PAS monter ou s'asseoir sur la porte. Installez la
bride anti-basculement fournie avec la cuisinière.
- La cuisinière pourrait basculer et entraîner des blessures
causées par du liquide chaud ou des aliments chauds qui
renversent, ou par la cuisinière elle-même.
- Si vous décollez la cuisinière du mur pour la nettoyer, la
réparer ou pour toute autre raison, vérifiez que le
dispositif anti-basculement est correctement remis en
place une fois la cuisinière de nouveau poussée contre le
mur.
Toutes les cuisinières peuvent basculer et provoquer des
blessures. Pour éviter le basculement accidentel de la
cuisinière, fixez au mur un dispositif anti-basculement
approuvé. (Voir Installation du dispositif anti-basculement
dans ce manuel.) Pour vérifier si le dispositif est bien
installé et enclenché, essayez de faire basculer la
cuisinière vers l'avant. Le dispositif anti-basculement d
oit
s'enclencher et empêcher la cuisinière de basculer.
Si vous décollez la cuisinière du mur pour quelque raison
que ce soit, assurez-vous que le dispositif anti-
basculement est enclenché lorsque vous poussez la
cuisinière de nouveau contre le mur.
AVERTISSEMENT!
• TOUTES LES CUISINIÈRES
PEUVENT BASCULER
• CELA PEUT PROVOQUER DES
BLESSURES
• INSTALLEZ LES DISPOSITIFS ANTI-
BASCULEMENT FOURNIS AVEC LA
CUISINIÈRE
• VOIR L'INSTALLATION
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
dans d''autres langues
- English: LG LRG3081ST Operating instructions
Documents connexes
-
LG LRG30357ST Mode d'emploi
-
LG LRG3060ST Le manuel du propriétaire
-
LG LSG5513BD Le manuel du propriétaire
-
LG LDG5315ST Le manuel du propriétaire
-
-
LG SKSGR360GS Le manuel du propriétaire
-
LG LSG4515BM Le manuel du propriétaire
-
-
LG LSSG3019BD Le manuel du propriétaire
-