Electrolux ESF2430W Manuel utilisateur
- Catégorie
- Lave-vaisselle
- Taper
- Manuel utilisateur
user manual
notice d'utilisation
benutzerinformation
istruzioni per l’uso
Dishwasher
Lave-vaisselle
Geschirrspüler
Lavastoviglie
ESF2430
Electrolux. Thinking of you.
Share more of our thinking at www.electrolux.com
Contents
Safety information 2
Product description 3
Control panel 4
Use of the appliance 5
Setting the water softener 5
Use of dishwasher salt 6
Use of rinse aid 6
Loading cutlery and dishes 7
Use of detergent 8
Washing programmes 9
Setting and starting a washing programme
10
Care and cleaning 10
What to do if… 11
Technical data 13
Installation 13
Water connection 14
Electrical connection 15
Environment concerns 15
Subject to change without notice
Safety information
For your safety and correct operation of
the appliance, read this manual carefully
before installation and use. Always keep
these instructions with the appliance
even if you move or sell it. Users must
fully know the operation and safety fea-
tures of the appliance.
Correct use
• The appliance is designed exclusively for
domestic use.
• Only use the appliance to clean household
utensils that are applicable for dishwash-
ers.
• Do not put solvents in the appliance. Risk
of explosion.
• Put the knives and all items with sharp
points in the cutlery basket with their
points down. If not, put in a horizontal po-
sition in the main basket.
• Use only branded products for dishwash-
ers (detergent, salt, rinse aid).
• If you open the door while the appliance is
in operation, hot steam can escape. Risk
of skin burns.
•Do not remove dishes from the dishwasher
before the end of the washing programme.
• When the washing programme is comple-
ted, disconnect the mains plug from the
mains socket and close the water tap.
• Only an authorised service engineer can
repair this appliance. Use only original
spare parts.
• Do not do repairs yourself to prevent injury
and damage to the appliance. Always con-
tact your local Service Force Centre.
General safety
• Persons (including children) with reduced
physical sensory, mental capabilities or
lack of experience and knowledge must
not use the appliance. They must have su-
pervision or instruction for the operation of
the appliance by a person responsible for
their safety.
• Obey the safety instructions from the man-
ufacturer of the dishwasher detergent to
prevent burns to eyes, mouth and throat.
• Do not drink the water from the dishwash-
er. Detergent residues can stay in your ap-
pliance.
• Always close the door when you do not
use the appliance to prevent injury and not
to stumble over the open door.
• Do not sit or stand on the open door.
Child safety
• Only adults can use this appliance. Chil-
dren must get supervision to make sure
that they do not play with the appliance.
• Keep all the packaging away from children.
There is a risk of suffocation.
• Keep all detergents in a safe area. Do not
let children touch the detergents.
• Keep children away from the appliance
when the door is open.
2 electrolux
Installation
• Make sure that the appliance is not dam-
aged because of transport. Do not con-
nect a damaged appliance. If necessary,
contact the supplier.
• Remove all packaging before first use.
• A qualified and competent person must do
the electrical installation.
• A qualified and competent person must do
the plumbing installation.
• Do not change the specifications or modify
this product. Risk of injury and damage to
the appliance.
• Do not use the appliance:
– if the mains cable or water hoses are
damaged,
– if the control panel, worktop or plinth
area are damaged, that you can get ac-
cess to the inner side of the appliance.
Contact your local Service Force Centre.
• Do not drill into the sides of the appliance
to prevent damage to hydraulic and elec-
trical components.
Warning! Carefully obey the
instructions for electrical and water
connections.
Product description
1
6
5
4
2
3
1 Spray arm
2 Microfilter
3 Detergent dispenser
4 Rinse aid dispenser
5 Flat filter
6 Salt container
electrolux 3
The rating label is on the back of appli-
ance.
Control panel
1 2 3
5 4
1 Programme knob
2 Start/cancel button
3 Delay start button
4 Indicator lights
5 On/off indicator light
Indicator lights
The indicator light comes on when the washing
phase or the rinsing phase operates.
The indicator light comes on when the drying
phase operates.
The indicator light comes on when the washing
programme is completed. Auxiliary functions:
• Level of the water softener.
• An alarm if the appliance has a malfunction.
1)
The indicator light comes on when it is necessary
to fill the salt container. Refer to the chapter 'Use
of dishwasher salt'.
The salt indicator light can stay on for some hours,
but it does not have an unwanted effect on the
operation of the appliance.
1) The indicator light is off while a washing programme operates.
Delay start button
Use the delay start button to delay the start
of the washing programme with an interval of
3 hours. Refer to the chapter 'Setting and
starting a washing programme'.
Programme knob and on/off indicator
light
• To set a washing programme, turn the
programme knob clockwise or anticlock-
wise. The programme marker on the pro-
gramme knob must agree with one of the
washing programmes on the control pan-
el.
– The on/off indicator light comes on (po-
sition ON).
• To set the appliance to the off position,
turn the programme knob until the pro-
gramme marker agrees with the on/off in-
dicator light.
– The on/off indicator light goes off (posi-
tion OFF).
4 electrolux
Use of the appliance
Refer to the following instructions for each
step of procedure:
1. Make a check if the water softener level
is correct for the water hardness in your
area. If necessary set the water softener.
2. Fill the salt container with dishwasher salt.
3. Fill the rinse aid dispenser with rinse aid.
4. Load cutlery and dishes into the dish-
washer.
5. Set the correct washing programme for
the type of load and soil.
6. Fill the detergent dispenser with the cor-
rect quantity of detergent.
7. Start the washing programme.
If you use detergent tablets, refer to the
chapter 'Use of detergent'.
Setting the water softener
The water softener removes minerals and
salts from the water supply. Minerals and
salts can have bad effect on the operation of
the appliance.
Water hardness is measured in equivalent
scales:
• German degrees (dH°).
• French degrees (°TH).
• mmol/l (millimol per litre - international unit
for the hardness of water).
•Clarke.
Adjust the water softener in to the water
hardness in your area. If necessary, contact
your local water authority.
Water hardness
Water hardness
setting
°dH mmol/l °TH Clarke
>24 >4.2 >40 > 29 10
22- 24 3,9- 4,2 39- 40 27- 29 9
20- 22 3,5- 3,9 35- 39 25- 27 8
18- 20 3,2- 3,5 32- 35 23- 25 7
16- 18 2,8- 3,2 28- 32 20- 23 6
13- 16 2,3- 2,8 23- 28 17-20 5
10- 13 1,8- 2,3 18- 23 13- 17 4
7- 10 1,2- 1,8 12- 18 9- 13 3
4- 7 0.7- 1,2 7- 12 5- 9 2
< 4 < 0.7 < 7 < 5
1
1)
1) No use of salt required.
Electronic adjustment
The water softener is set at the factory
at level 5.
1. Press and hold the start/cancel button.
Turn the programme knob clockwise until
the programme marker agrees with the
first washing programme on the control
panel.
2. Release the start/cancel button when the
on/off indicator light and the start/cancel
indicator light start to flash.
– At the same time, the end indicator
light flashes to show the level of the
water softener.
Example:
5 flashes, pause, 5 flashes, pause,
etc... = level 5
3. Press the start/cancel button one time to
increase the water softener level by one
step.
The end indicator light shows the new
level.
4. Turn the programme knob to the off po-
sition to save the operation.
electrolux 5
Use of dishwasher salt
Caution! Only use dishwashers salt.
Types of salt that are not applicable for
dishwashers cause damage to the water
softener.
Caution! Grains of salt and salty water
on the bottom of the appliance can
cause corrosion. Fill the appliance with
salt before you start a washing
programme to prevent corrosion.
Do these steps to fill the salt container:
1. Turn the cap anticlockwise to open the
salt container.
2. Fill the salt container with 1 litre of water
(only the first operation).
3. Use the funnel to fill the salt container with
salt.
4. Remove the salt around the opening of
the salt container.
5. Turn the cap clockwise to close the salt
container.
It is normal that water overflows from the
salt container when you fill it with salt
When you set the water softener to level 1,
the salt indicator light does not stay on.
Use of rinse aid
Caution! Only use branded rinse aid for
dishwashers.
Do not fill the rinse aid dispenser with
other products (e.g. dishwasher clean-
ing agent, liquid detergent). There is a
risk of damage to the appliance.
Rinse aid makes it possible to dry the
dishes without streaks and stains.
Rinse aid is automatically added during
the last rinsing phase.
Fill the rinse aid dispenser when the rinse
aid indicator (B) becomes clear.
Do these steps to fill the rinse aid dispenser:
6 electrolux
B
1. Press the release button (A) to open the
rinse aid dispenser.
2. Fill the rinse aid dispenser with rinse aid.
The mark 'max.' shows the maximum
level .
3. Remove the spilled rinse aid with an ab-
sorbent cloth to prevent too much foam
during the subsequent washing pro-
gramme.
4. Close the rinse aid dispenser.
The capacity of the rinse aid dispenser
is approximately 150 ml. The quantity of
rinse aid is sufficient for approximately
60 washing programmes.
Adjust the dosage of rinse aid
The appliance is set at the factory at level 1.
You can set the rinse aid dosage between 1
- 6 (1- 6 ml of the rinse aid).
Refer to the washing results (chapter 'What
to do if...'). Start with the lowest dosage.
1. Turn the arrow clockwise to increase the
dosage.
2. Increase the dosage if there are water
droplets or limescale on the dishes.
Loading cutlery and dishes
Helpful hints and tips
Caution! Only use the appliance for
household utensils that are applicable
for dishwashers.
Do not use the appliance to clean objects
that can absorb water (sponges, household
cloths, etc.).
• Before you load cutlery and dishes, do
these steps:
– Remove all food remainings and debris.
– Make burnt, remaining food in pans soft.
• While you load cutlery and dishes, do
these steps:
– Load hollow items (e.g. cups, glasses
and pans) with the opening down.
– Make sure that water does not collect in
the container or in a deep base.
– Make sure that cutlery and dishes do not
lie inside one another.
– Make sure that cutlery and dishes do not
cover other cutlery and dishes.
– Make sure that glasses do not touch
other glasses.
– Put small objects in the cutlery basket.
• Plastic items and pans with non-stick
coatings can keep water droplets.
• Plastic items do not dry as well as porce-
lain and steel items.
• Put light items in the main basket. Make
sure that the items do not move.
Caution! Make sure that the spray arm
can move freely before you start a
washing programme.
Primary basket
Arrange the deep dishes and large lids
around the edge of the basket. Arrange items
on and below the cup racks. The water must
come to all parts of the dishes.
You can fold the cup racks to clean high
items.
electrolux 7
Cutlery basket
Warning! Do not put long-bladed knives
in a vertical position to prevent injury.
Arrange long and/or sharp items of cutlery
horizontally in the primary basket. Be careful
with sharp items such as knives.
Use the cutlery basket for:
• Forks and spoons with the handles down.
• Knives with the handles up.
The cutlery basket has a cutlery grid that you
can remove.
Do not let the cutlery bond together.
Make sure that the spray arm can move
freely before you close the door.
Use of detergent
Only use detergents (powder, liquid or
tablet) that are applicable for dishwash-
ers.
Follow the data on the packaging:
• Dosage recommended by the manu-
facturer.
• Storage recommendations.
The instructions on the packaging usu-
ally refer to large dishwashers (12 set-
tings).
Do not use more than the correct quan-
tity of detergent to save an environment.
Fill with detergent
Do these steps to fill the detergent dispenser:
A
B
1. Open the lid of the detergent dispenser.
2. Fill the detergent dispenser (A) with de-
tergent.
3. If you use a washing programme with
prewash phase, put more detergent in
the prewash detergent compartment (B).
The detergent is removed during the pre-
wash phase.
4. Close the lid of the detergent dispenser.
Use of detergent tablets
Put the detergent tablet in the detergent dis-
penser (A).
Detergent tablets contain:
• detergent
•rinse aid
• other cleaning agents.
Do these steps to use detergent tablets:
1. Make sure that the detergent tablets are
applicable for your water hardness. Refer
to the instructions from the manufacturer.
2. Set the lowest levels of water hardness
and rinse aid dosage.
It is not necessary to fill the salt container
and the rinse aid dispenser.
Do these steps when the drying results
are not satisfactory:
1. Fill the rinse aid dispenser with rinse aid.
2. Set the rinse aid dosage to position 2.
8 electrolux
Do these steps to use the detergent
powder again:
1. Fill the salt container and the rinse aid
dispenser.
2. Set the water softener to the highest level.
3. Do a washing programme without
dishes.
4. Adjust the water softener. Refer to the
chapter 'Setting the water softener'.
5. Adjust the rinse aid dosage.
Different brands of detergent dissolve in
different times. Some detergent tablets
do not have the best cleaning results
during short washing programmes. Use
long washing programmes when you
use detergent tablets to fully remove the
detergent.
Washing programmes
Washing programmes
Programme
Pro-
gramme
knob posi-
tion
Degree of
soil
Type of load Programme description
A Heavy soil
Crockery,
cutlery, pots
and pans
Prewash
Main wash up to 70°C
2 intermediate rinses
Final rinse
Drying
B Normal soil
Crockery and
cutlery
Prewash
Main wash up to 65°C
1 intermediate rinse
Final rinse
Drying
1)
C Normal soil
Crockery and
cutlery
Prewash
Main wash up to 55°C
1 intermediate rinse
Final rinse
Drying
D
Normal or
light soil
Crockery and
cutlery
Main wash up to 50°C
1 intermediate rinse
Final rinse
E
Normal or
light soil
Delicate
crockery and
glassware
Main wash up to 40°C
1 intermediate rinse
Final rinse
1) Test programme for test institutes. Please refer to separate leaflet supplied, for test data.
Consumption values
Programme Programme duration
(in minutes)
Energy consumption
(in kWh)
Water consumption
(in litres)
117 1,15 9
94 0,80 7
157 0,63 7
36 0,40 6
31 0,35 6
The consumption values are intended as
a guide and depends on the pressure
electrolux 9
and the temperature of the water and al-
so by the variations of the power supply
and the amount of dishes.
Setting and starting a washing programme
Do these steps to set and start a washing
programme:
1. Close the door.
2. Turn the programme knob to set the
washing programme. Refer to the chap-
ter 'Washing programmes'.
– The on/off indicator light comes on.
– The phase indicator light for the wash-
ing programme starts to flash.
3. Press the start/cancel button.
– The washing programme starts auto-
matically.
– The start/cancel indicator light comes
on.
– When the programme starts, only the
phase in progress indicator light stays
on.
When the washing programme oper-
ates, you cannot change the pro-
gramme. Cancel the washing pro-
gramme.
Warning! Only interrupt or cancel a
washing programme if necessary.
Caution! Open the door carefully. Hot
steam can come free.
Cancelling a washing programme
•Press and hold the start/cancel button for
approximately 5 seconds.
– The start/cancel indicator light goes off.
– The phase indicator lights starts to flash.
The washing programme is cancelled.
At this time you can do these steps:
1. Switch off the appliance.
2. Set a new washing programme.
Fill the detergent dispenser with detergent
before you set a new washing programme.
Interrupting a washing programme
Open the door.
• The programme stops.
Close the door.
• The programme continues from the point
of interruption.
Setting and starting a washing
programme with delay start
1. Set a washing programme.
2. Press the delay start button.
– The delay start indicator light comes
on.
3. Press the start/cancel button.
– The countdown of the delay start
starts.
– The phase indicator lights go off.
When the countdown is completed, the
washing programme automatically starts.
• The delay start indicator light goes off.
• The phase indicator light comes on.
Do not open the door during the count-
down to prevent interruption of the
countdown. When you close the door
again, the countdown continues from
the point of interruption.
Cancelling a delay start:
1. Press and hold the start/cancel button for
approximately 5 seconds.
– The start/cancel indicator light and de-
lay start indicator light go off.
– The phase indicator lights start to flash.
2. Press the start/cancel button to start the
washing programme.
End of the washing programme
Switch off the appliance in these conditions:
• The appliance stops automatically.
• The end indicator light comes on.
For better drying results, keep the door ajar
for some minutes before you remove the
dishes.
Let the dishes cool down before you remove
them from the appliance. Hot dishes are
easily damaged.
Care and cleaning
Warning! Switch the appliance off
before you clean the filters.
10 electrolux
Cleaning the filters
Caution! Do not use the appliance
without filters. Make sure that the
installation of the filters is correct.
Incorrect installation will cause
unsatisfactory washing results and
damage to the appliance.
The dishwasher has 2 filters:
1. microfilter
2. flat filter
Do these steps to clean the filters:
1. Open the door.
2. Remove the basket.
3. Remove the filters in the bottom of the
appliance.
4. Clean the filters below running water.
5. Put the filters back.
6. Turn the microfilter clockwise to lock it.
7. Close the door.
Cleaning the spray arm
Regularly examine the spray arm. Remove
remaining food from the holes in the spray
arm.
Do these steps to remove the spray arm:
1. Turn the nut anticlockwise.
2. Remove the spray arm.
3. Fully clean the holes.
External cleaning
Clean the external surfaces of the appliance
and control panel with a damp soft cloth.
Only use neutral detergents. Do not use
abrasive products, scouring pads or solvents
(acetone, trichloroethylene etc...).
Frost precautions
Caution! Do not install the appliance
where the temperature is below 0 °C.
The manufacturer is not responsible for
damage because of frost.
If not possible, empty the appliance and
close the door. Disconnect the water inlet
hose and remove water from the water inlet
hose.
What to do if…
The appliance does not start or stops during
operation.
If there is a fault, first try to find a solution to
the problem yourself. If you cannot find a sol-
ution to the problem yourself, contact the
Service Force Centre.
electrolux 11
Fault code and malfunction Possible cause and solution
• continuous flash of the start/can-
cel indicator light
• 1 flash of the end indicator light
The dishwasher does not fill with wa-
ter
• The water tap is blocked or furred with limescale.
Clean the water tap.
• The water tap is closed.
Open the water tap.
• The filter in the water inlet hose is blocked.
Clean the filter.
• The connection of the water inlet hose is not correct. The
hose can be kinked or squashed.
Make sure that the connection is correct.
• continuous flash of the start/can-
cel indicator light
• 2 flashes of the end indicator light
The dishwasher will not drain
• There is a blockage in the sink spigot.
Clean the sink spigot.
• The connection of the water drain hose is not correct. The
hose can be kinked or squashed.
Make sure that the connection is correct.
• the drain pump operates continu-
ously
• all indicators lights on the control
panel go off
The anti-flood device operates
• Close the water tap and contact your local Service Force
Centre.
The programme does not start • The appliance door is not closed.
Close the door.
• Mains plug is not connected in.
Put in the mains.
• The fuse has blown out in the household fuse box.
Replace the fuse.
• Delay start is set.
Cancel the delay start to start the programme immediately.
After the check, switch on the appliance. The
programme continues from the point of in-
terruption. If the malfunction shows again,
contact your Service Force Centre.
These data are necessary to help you quickly
and correctly:
•Model (Mod.)
• Product number (PNC)
• Serial number (S.N.)
For these data, refer to the rating plate.
Write the necessary data here:
Model description : ..........
Product number : ..........
Serial number : ..........
The cleaning results are not satisfactory
The dishes are not clean • The selected washing programme is not applicable for the type of
load and soil.
• The basket is loaded incorrectly so that water cannot reach all sur-
faces.
• Spray arm does not turn freely because of incorrect arrangement of
the load.
• The filters are dirty or not correctly installed.
• The quantity of detergent is too little or missing.
Limescales particles on the
dishes
• The salt container is empty.
• The water softener is adjusted on a wrong level.
• The salt container cap is not closed correctly.
The dishes are wet and dull • No rinse aid has been used.
• The rinse aid dispenser is empty.
There are streaks, milky spots
or a bluish coating on glasses
and dishes
• Decrease the rinse aid dosage.
12 electrolux
The cleaning results are not satisfactory
Dry water drop signs on
glasses and dishes
• Increase rinse aid dosage.
• The detergent can be the cause.
Technical data
Dimensions Width
Height
Depth
54,5 cm
44,7 cm
48,0-49,0 cm
Electrical connection - Voltage -
Overall power - Fuse
Data on the electrical connection are on the rating plate on the back
of appliance.
Water supply pressure Minimum
Maximum
0,8 bar (0,08 MPa)
10 bar (1,0 MPa)
Capacity 6 place settings
Installation
Warning! Make sure that mains plug is
disconnected from the mains socket
during installation.
Fitting the appliance
Put the appliance adjacent to a water tap and
a drain.
When you put the appliance in place, make
sure that the water hoses are not kinked or
squashed.
Install the appliance on a kitchen sink, work-
top or built-in..
Positioning
Install the dishwasher into the furniture of the
kitchen.
Make sure that the dimensions of the recess
agree with the given dimensions.
Make sure that there are openings in the fur-
niture for the inlet hose, the water drain hose
and the mains cable.
Adjusting the level of the appliance
Make sure that the appliance is level to close
and seal the door correctly. If the level of the
appliance is correct, the door does not catch
on the sides of the cabinet. If the door does
not close correctly, loosen or tighten the ad-
justable feet until the appliance is level.
electrolux 13
Water connection
Inlet hose
The appliance has safety features to prevent
that the water in the appliance goes back into
the drinking water system.
Connected the appliance to a hot (max. 60°)
or cold water supply.
If the hot water comes from alternative sour-
ces of energy that are more environmentally
friendly (e.g. solar or photovoltaic panels and
aeolian), use a hot water supply to decrease
energy consumption.
It is important that a water tap or stopcock is
near the dishwasher with easy access.
Connect the inlet hose to a water tap with an
external thread of 3/4”.
If the water inlet hose is too short, replace the
water inlet hose with an applicable, longer
high-pressure hose. Do not connect an ex-
tension hose.
To suit the installation, it is possible to turn
the end of the hose that is connected to the
dishwasher. Do these steps :
1. Loosen the retaining nut.
2. Turn the hose.
3. Tighten the retaining nut.
Warning! Make sure that the retaining
nut and all other connections are tight
before you move the dishwasher into
position.
Warning! Always use a new water inlet
hose. Do not use connection hoses from
an old appliance.
Drain hose
The appliance has water safety system to
prevent water damage. If there is a malfunc-
tion, the drain pump automatically starts to
drain the remaining water out of the dish-
washer.
Warning! Only if the dishwasher is
connected to the mains socket, the
water safety system operates when the
dishwasher is off.
2 procedures are possible to install the water
drain hose :
1. Attach the plastic curve supplied at the
end of the hose.
Put the water drain hose in the sink.
2. Connect the water drain hose to the wa-
ter drain system.
The hose must be less than 75 cm above
the bottom of the dishwasher to prevent
incorrect operation of appliance.
If you connect the water drain hose to a trap
spigot under the sink, remove the plastic
membrane (A). If you do not remove the
membrane, remaining food can cause a
blockage in the drain hose spigot
14 electrolux
Electrical connection
Warning! The manufacturer is not
responsible if you do not follow these
safety precautions.
Ground the appliance according to safe-
ty precautions.
Make sure that the rated voltage and
type of power on the rating plate agree
with the voltage and the power of the lo-
cal power supply.
Always use a correctly installed shock-
proof socket.
Do not use multi-way plugs, connectors
and extension cables. There is a risk of
fire.
Do not replace the mains cable yourself.
Contact the Service Force Centre.
Make sure that the mains plug is acces-
sible after installation.
Do not pull the mains cable to discon-
nect the appliance. Always pull the
mains plug.
Environment concerns
The symbol on the product or on its
packaging indicates that this product may
not be treated as household waste. Instead
it should be taken to the appropriate
collection point for the recycling of electrical
and electronic equipment. By ensuring this
product is disposed of correctly, you will help
prevent potential negative consequences for
the environment and human health, which
could otherwise be caused by inappropriate
waste handling of this product. For more
detailed information about recycling of this
product, please contact your local council,
your household waste disposal service or the
shop where you purchased the product.
The packaging materials are environmentally
friendly and can be recycled. The plastic
components are identified by markings, e.g.
>PE<, >PS<, etc. Discard the packaging
materials in the applicable container at the
community waste disposal facilities.
Warning! To discard the appliance,
follow the procedure:
• Pull the mains plug out of the socket.
• Cut off the mains cable and mains
plug and discard them.
• Discard the door catch. This prevents
the children to close themselves in-
side the appliance and endanger their
lives.
electrolux 15
Electrolux. Thinking of you.
Partagez notre imagination sur www.electrolux.com
Sommaire
Consignes de sécurité 16
Description de l'appareil 18
Bandeau de commande 18
Utilisation de l'appareil 19
Réglage de l'adoucisseur d'eau 20
Utilisation du sel régénérant 20
Utilisation du liquide de rinçage 21
Rangement des couverts et de la vaisselle
22
Utilisation du produit de lavage 23
Programmes de lavage 24
Sélection et départ d'un programme de
lavage 25
Entretien et nettoyage 26
Que faire si… 27
Caractéristiques techniques 28
Installation 29
Raccordement à l'arrivée d'eau 29
Branchement électrique 31
En matière de protection de
l'environnement 31
Sous réserve de modifications
Consignes de sécurité
Pour votre sécurité et le bon fonctionne-
ment de l'appareil, lisez attentivement ce
manuel avant l'installation et l'utilisation.
Conservez ces instructions à proximité
de l'appareil. Les utilisateurs doivent
connaître parfaitement le fonctionne-
ment et les fonctions de sécurité de l'ap-
pareil.
Utilisation réglementaire
• Cet appareil est exclusivement destiné à
un usage domestique.
• Ce lave-vaisselle est conçu pour laver la
vaisselle et les ustensiles de cuisine pou-
vant être lavés en machine.
• N'utilisez pas de solvants dans votre ap-
pareil. Ceux-ci pourraient provoquer une
explosion !
• Les couteaux et autres ustensiles pointus
ou tranchants doivent être placés dans le
panier à couverts avec la pointe vers le
bas, ou placez-les en position horizontale
dans le panier principal.
• N'utilisez que des produits (sel, produit de
lavage, liquide de rinçage) spécifiques
pour lave-vaisselle.
• Evitez d'ouvrir la porte pendant que l'ap-
pareil fonctionne : une vapeur brûlante
peut s'en échapper. Risque de brûlures !
• Ne sortez pas la vaisselle du lave-vaisselle
avant la fin du cycle de lavage.
• Lorsque le programme est terminé, dé-
branchez l'appareil et fermez le robinet
d'arrivée d'eau.
• Cet appareil ne peut être entretenu et ré-
paré que par un technicien autorisé, ex-
clusivement avec des pièces d'origine.
• N'essayez en aucun cas de réparer le lave-
vaisselle vous-même. Les réparations ef-
fectuées par du personnel non qualifié
peuvent provoquer des blessures ou le
mauvais fonctionnement du lave-vaisselle.
Contactez votre Service Après-vente. Exi-
gez des pièces d'origine.
Sécurité générale
• Les personnes (y compris les enfants) qui
souffrent de capacités mentales, physi-
ques et sensorielles réduites ou qui ne se
sont pas familiarisées avec le mode de
fonctionnement de l'appareil, ne doivent
pas l'utiliser. Elles doivent être surveillées
ou dirigées par une personne responsable
de leur sécurité.
• Respectez les consignes de sécurité du
fabricant du détergent pour éviter les brû-
lures aux yeux, à la bouche et la gorge.
• Ne buvez pas l'eau du lave-vaisselle. Des
résidus de produit de lavage peuvent res-
ter dans l'appareil.
• Fermez toujours la porte de l'appareil lors-
qu'il n'est pas utilisé pour empêcher tout
risque de blessure ou de chute acciden-
telle.
16 electrolux
• Ne vous asseyez pas ou ne montez pas
sur la porte ouverte.
Sécurité enfants
• Seuls les adultes doivent utiliser cet appa-
reil. Veillez à ce que les enfants ne jouent
pas avec l'appareil.
• Rangez les emballages hors de la portée
des enfants. Ils présentent un risque de
suffocation.
• Rangez les détergents dans un endroit
sûr. Veillez à ce que les enfants ne tou-
chent pas les produits de lavage.
• Ne laissez pas les enfants s'approcher de
l'appareil quand la porte est ouverte.
Installation
• Vérifiez que l'appareil n'a pas été endom-
magé pendant le transport. Ne branchez
pas un appareil endommagé. Si nécessai-
re, contactez le fournisseur.
• Déballez l'appareil avant de l'utiliser pour
la première fois.
• Une personne compétente et qualifiée doit
prendre en charge l'installation électrique.
• Une personne compétente et qualifiée doit
prendre en charge le travail de plomberie.
• Ne modifiez ni les spécifications ni le pro-
duit. Risque de blessure ou d'endomma-
gement de l'appareil.
• N'utilisez pas l'appareil :
– si le câble secteur ou les tuyaux d'eau
sont endommagés,
– si le bandeau de commande, le plan de
travail ou la plinthe sont endommagés,
si vous pouvez accéder à l'intérieur de
l'appareil.
Contactez le service après-vente de votre
magasin vendeur.
• Ne percez pas dans les côtés de l'appareil
pour ne pas endommager les composants
électriques et hydrauliques.
Avertissement Respectez
scrupuleusement les consignes
données pour les branchements
électriques et le raccordement de l'eau.
electrolux 17
Description de l'appareil
1
6
5
4
2
3
1 Bras d'aspersion
2 Microfiltre
3 Distributeur de produit de lavage
4 Distributeur de liquide de rinçage
5 Filtre plat
6 Réservoir à sel régénérant
La plaque signalétique est située à l'ar-
rière de l'appareil.
Bandeau de commande
1 2 3
5 4
18 electrolux
1 Sélecteur de programme
2 Touche Départ/Annulation
3 Touche Départ différé
4 Voyants
5 Voyant Marche/Arrêt
Voyants
Le voyant s'allume quand la phase de lavage ou
de rinçage est en cours.
Le voyant s'allume quand la phase de séchage est
en cours.
Le voyant s'allume quand le programme de lavage
est terminé. Fonctions auxiliaires :
• Niveau de l'adoucisseur.
• Une alarme se déclenche en cas de défaillance
de l'appareil.
1)
Le voyant s'allume quand il faut remplir le réservoir
à sel. Consultez le chapitre " Utilisation du sel dans
le lave-vaisselle ".
Le voyant Sel reste allumé pendant plusieurs heu-
res, mais cela n'affecte pas le fonctionnement de
l'appareil.
1) Le voyant est éteint pendant qu'un programme de lavage est en cours.
Touche Départ différé
Utilisez la touche Départ différé pour différer
l'heure de départ du programme de 3 heu-
res. Reportez-vous au chapitre "Réglage et
départ d'un programme de lavage".
Sélecteur de programme et voyant
Marche/Arrêt
• Pour sélectionner un programme de lava-
ge, tournez le sélecteur de programme
vers la droite ou la gauche. L'indicateur de
programme du sélecteur doit correspon-
dre à l'un des programmes de lavage sur
le bandeau de commande.
– Le voyant Marche/Arrêt s'allume (posi-
tion MARCHE).
• Pour mettre l'appareil à l'arrêt, tournez le
sélecteur de programme jusqu'à ce que
l'indicateur de programme corresponde
au voyant Marche/Arrêt.
– Le voyant Marche/Arrêt s'éteint (posi-
tion ARRET).
Utilisation de l'appareil
Consultez les instructions suivantes pour
chaque étape de la procédure :
1. Vérifiez que le niveau de l'adoucisseur
d'eau est adapté à la dureté de l'eau de
votre région. Le cas échéant, réglez
l'adoucisseur.
2. Remplissez le réservoir à sel.
3. Remplissez le distributeur de liquide de
rinçage.
4. Placez les plats et les couverts dans le
lave-vaisselle.
5. Sélectionnez le programme de lavage qui
convient au type de vaisselle et au niveau
de salissure.
6. Remplissez le distributeur de produit de
lavage.
7. Démarrez le programme de lavage.
Si vous utilisez des pastilles, consultez le
chapitre "Utilisation du produit de lava-
ge.
electrolux 19
Réglage de l'adoucisseur d'eau
L'adoucisseur d'eau élimine les minéraux et
les sels de l'alimentation en eau. Les sels et
les minéraux peuvent affecter le fonctionne-
ment de l'appareil.
La dureté de l'eau est mesurée par échelles
équivalentes :
• °dH allemand.
• °TH français.
• mmol/l (millimole par litre – unité interna-
tionale de la dureté de l'eau).
•Clarke.
Ajustez l'adoucisseur en fonction de la dure-
té de l'eau de votre région. Le cas échéant,
contactez votre compagnie des eaux.
Dureté de l'eau
Réglage de la du-
reté de l'eau
°dH mmol/l °TH Clarke.
>24 >4.2 >40 > 29 10
22- 24 3,9- 4,2 39- 40 27- 29 9
20- 22 3,5- 3,9 35- 39 25- 27 8
18- 20 3,2- 3,5 32- 35 23- 25 7
16- 18 2,8- 3,2 28- 32 20- 23 6
13- 16 2,3- 2,8 23- 28 17-20 5
10- 13 1,8- 2,3 18- 23 13- 17 4
7- 10 1,2- 1,8 12- 18 9- 13 3
4- 7 0.7- 1,2 7- 12 5- 9 2
< 4 < 0.7 < 7 < 5
1
1)
1) Aucun sel requis.
Réglage électronique
L'adoucisseur est réglé d'usine sur le ni-
veau 5.
1. Appuyez sur la touche Départ/Annulation
et maintenez-la appuyée. Tournez le sé-
lecteur de programme vers la droite jus-
qu'à ce que l'indicateur de programme
corresponde au premier programme de
lavage sur le bandeau de commande.
2. Relâchez la touche Départ/Annulation
lorsque le voyant Marche/Arrêt et le voy-
ant Départ/Annulation clignotent.
– Le voyant de fin de cycle clignote si-
multanément pour indiquer le niveau
de l'adoucisseur.
Exemple :
5 clignotements, pause, 5 clignote-
ments, pause, etc. = niveau 5
3. Chaque pression de la touche Départ/
Annulation détermine le niveau suivant.
Le voyant Fin vous indique le nouveau ni-
veau.
4. Tournez le sélecteur de programme sur
la position Arrêt pour mémoriser l'opéra-
tion.
Utilisation du sel régénérant
Attention Utilisez uniquement du sel
spécial pour lave-vaisselle. Tout autre
type de sel non spécialement étudié
pour être utilisé dans un lave-vaisselle,
en particulier le sel de cuisine, peut
endommager l'adoucisseur d'eau.
Attention Pour éviter que des grains de
sel ou de l'eau salée qui a débordé
n'entre en contact avec le fond de la
cuve pendant un laps de temps
prolongé, approvisionnez en sel juste
avant de démarrer un programme de
lavage complet pour éviter tout risque de
corrosion.
Pour réapprovisionner, procédez com-
me suit :
20 electrolux
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
Electrolux ESF2430W Manuel utilisateur
- Catégorie
- Lave-vaisselle
- Taper
- Manuel utilisateur
dans d''autres langues
- italiano: Electrolux ESF2430W Manuale utente
- English: Electrolux ESF2430W User manual
- Deutsch: Electrolux ESF2430W Benutzerhandbuch