Ryobi RY401014 Manuel utilisateur

Catégorie
Tondeuses à gazon
Taper
Manuel utilisateur

Ce manuel convient également à

OPERATOR’S MANUAL
MANUEL D’UTILISATION
MANUAL DEL OPERADOR
21 in. 40 VOLT LAWN MOWER
21 po, TONDEUSE 40 V
21 pulg., PODADORA 40 V
RY401014
Important Safety Instructions ......... 2-4
Symbols ......................................... 4-5
Features .............................................6
Assembly ....................................... 7-8
Operation ..................................... 8-11
Maintenance .............................. 11-12
Troubleshooting ...............................13
Parts Ordering and
Service ............................... Back Page
Instructions importantes
concernant la securite ..................... 2-4
Symboles ....................................... 4-5
Caractéristiques .................................6
Assemblage ................................... 7-8
Utilisation ..................................... 8-11
Entretien ..................................... 11-12
Dépannage ....................................... 13
Commande de pièces
et réparation ..................... Page arrière
Instrucciones de seguidad
importantes .................................... 2-4
Símbolos ........................................ 4-5
Características ...................................6
Armado .......................................... 7-8
Funcionamiento ........................... 8-11
Mantenimiento ........................... 11-12
Corrección de problemas ................13
Pedidos de piezas
y servicio ....................... Pág. posterior
WARNING: To reduce the
risk of injury, the user must read and
understand the operator’s manual
before using this product.
AVERTISSEMENT : Pour
réduire les risques de blessures,
l’utilisateur doit lire et veiller à bien
comprendre le manuel d’utilisation
avant d’employer ce produit.
ADVERTENCIA: Para reducir
el riesgo de lesiones, el usuario debe
leer y comprender el manual del
operador antes de usar este producto.
SAVE THIS MANUAL FOR
FUTURE REFERENCE
CONSERVER CE MANUEL
POUR FUTURE RÉFÉRENCE
GUARDE ESTE MANUAL
PARA FUTURAS CONSULTAS
ii
See this fold-out section for all of the figures
referenced in the operator’s manual.
Consulter l’encart à volets afin d’examiner toutes
les figures mentionnées dans le manuel d’utilisation.
Consulte esta sección desplegable para ver todas
las figuras a las que se hace referencia en el manual del operador.
Fig. 1
A - Carrying/lifting handle (poignée de transport/soulèvement, mango de
transporte/elevación)
B - LED headlights (phares DEL, luces delanteras LED)
C - Battery cover (couvercle des piles, tapa de las baterías)
D - Height adjustment handle (poignée de réglage de hauteur, mango de
ajuste de altura)
E - 2-position handle (poignée à deux positions, mango de 2 posiciones)
F - Handle lock lever (levier de verrou de la poignée, palanca de seguro del
mango)
D
G - Self-propel levers (leviers de fonction automotrice, palancas
autopropulsadas)
H - Bail (anse, asa)
I - Start button (bouton de démarrage, botón de arranque)J -
J - Cruise control (régulateur de vitesse, control de crucero)
K - Grass catcher (collecteur d’herbe, receptor de hierba)
L - Mulching plug (insert broyeur, tapón para trituración)
M - Start key (clé de démarrage, llave del arranque)
N - Side discharge chute (chute de décharge latérale, vertedor de descarga
lateral)
A
B
C
I
K
E
F
G
E
L
M
J
N
H
iii
Fig. 2
Fig. 3
A - 2-position handle (poignée à deux positions, mango de 2 posiciones)
B - Handle adjustment lever (levier de réglage de la poignée, palanca de
ajuste del mango)
C - To unlock (pour déverrouiller, para desbloquear)
D - To lock (pour verrouiller, para asegurar)
B
1
Fig. 4
Fig. 5
A - Clips (attaches, clips)
B - Hooks (crochets, ganchos)
E
A - Frame (support, armazón)
B - Bag (sac, bolsa)
C - Handle (poignée, mango)
D - Vinyl floor (plancher en vinyle, piso de vinilo)
E - Clip (attache, clip)
D
A
C
B
A
B
B
A
A
A
A - 2-position handle (poignée à deux positions, mango de 2 posiciones)
B - Handle adjustment lever (levier de réglage de la poignée, palanca de
ajuste del mango)
C - Upper notch (encoche supérieure, muesca superior)
D - Lower notch (encoche inférieur, muesca inferior)
A
C
D
B
C
D
A
C
2
iv
Fig. 11
A - Start key (clé de démarrage, llave del
arranque)
B - Battery cover (couvercle des piles, tapa de
las baterías)
C - Start key slot (fente de la clé de démarrage,
ranura de la llave del arranque)
A - Battery packs (bloc-piles, paquetes de
baterías)
B - Battery cover (couvercle des piles, tapa de
las baterías)
C - Dual battery port (deux ports de pile, puertos
de baterías dobles)
D - Latch (loquet, pestillo)
Fig. 9
BA
B
C
C
Fig. 10
Fig. 12
D
A
A - Height adjustment handle (poignée de
réglage de hauteur, mango de ajuste de
altura)
B - Lowest blade setting (le plus bas réglage de
la lame, ajuste más bajo de la hoja)
C - Highest blade setting (le plus haut réglage
de la lame, ajustes de cuchilla más alto)
A
B C
1
2
D
A
C
B
EF G
A - Bail (anse, asa)
B - Start button (bouton de démarrage, botón
de arranque)
C - Self-propel levers (leviers de fonction
automotrice, palancas autopropulsadas)
D - Upper handle (poignée supérieure, mango
superior)
E - Cruise control (régulateur de vitesse,
control de crucero)
F - Minimum self propelled speed (vitesse
autopropulsée minimum, velocidad de
autopropulsión mínima)
G - Maximum self propelled speed (vitesse
autopropulsée maximum, velocidad de
autopropulsión máxima)
Fig. 7
Fig. 8
B
C
D
A
A - Rear discharge opening (ouverture d’éjection
arrière, abertura de descarga posterio)
B - Mulching plug (insert broyeur, tapón para
trituración)
C - Tab (languette, lengüeta)
D - Slot (fente, ranura)
A - Grass catcher handle (poignée de collecteur
d’herbe, mango del receptor de hierba)
B - Rear discharge opening (ouverture d’éjection
latérale, abertura de descarga lateral)
C - Rear discharge door (couvercle d’éjection
arrière, puerta de descarga posterior)
D - Hooks (crochets, ganchos)
B
A C
Fig. 6
1
2
D
A - Mulch cover (couvercle broyeur, tapa para
trituración)
B - Side discharge chute (chute de décharge
latérale, vertedor de descarga lateral)
C - Tab (languette, lengüeta)
D - Notch (encoche, muesca)
B
A
C
D
v
Fig. 17
Fig. 16
TO STORE THE MACHINE
IN THE HORIZONTAL POSITION
POUR REMISER L’ÉQUIPEMENT
EN POSITION HORIZONTALE
PARA GUARDAR LA MÁQUINA
EN POSICIÓN HORIZONTAL
TO STORE THE MACHINE
IN THE VERTICAL POSITION
POUR REMISER L’ÉQUIPEMENT
EN POSITION VERTICALE
PARA GUARDAR LA MÁQUINA
EN POSICIÓN VERTICALE
Fig. 15 A
BC
Fig. 16
A - Adaptor (adaptateur, adaptador)
B - Hub (arbre, eje)
C - Blade post (half circle) [tige pour
lame (demi-cercle), puerto de la hoja
(semicircular)]
D - Blade post (round) [tiges pour lame
(ronde), montantes de cuchilla (Redondo)]
E - Blade (lame, hoja)
F - Blade hole (half circle) [trou pour
lame (demi-cercle), orificio de la hoja
(semicircular)]
G - Blade hole (round) [trou pour lame (ronde),
orificio de la hoja (redondo)]
H - Blade insulator (isolant de lame, aislante de
hoja)
I - Spacer (entretoise, separador)
J - Blade nut (écrou de lame, tuerca de la hoja)
K - Shaft (arbre, eje)
K
C
G
E
D
B
A
J
I
F
H
A - Blade (lame, hoja)
B - Wrench (clé, llave)
C - Block of wood (pièce de bois, bloque de
madera)
15° MAXIMUM
15° MAXIMAL
15° MÁXIMA
Fig. 14
Fig. 13
2 — English
WARNING:
READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below and on the
machine may result in electric shock, fire, and/or serious
personal injury.
READ ALL INSTRUCTIONS
This cutting machine is capable of amputating hands and
feet and throwing objects. Failure to observe all safety
instructions could result in serious injury or death.
Avoid dangerous environment – Do not use the lawn
mower in damp or wet conditions or operate in the rain.
Keep children away – Keep all bystanders, children, and
pets at least 100 ft. away. Stop machine if anyone enters
the area.
Tragic accidents can occur if the operator is not alert to
the presence of children. Children are often attracted to
the machine and the mowing activity. Never assume that
children will remain where you last saw them.
Keep children out of the mowing area and under the
watchful care of a responsible adult other than the
operator.
Be alert and turn mower off if a child enters the area.
Never allow children to operate the machine.
Use extra care when approaching blind corners, shrubs,
trees, or other objects that may block your view of a
child.
Dress properly – Wear heavy, long pants, long sleeves,
gloves, and protective footwear that will protect your
feet and improve your footing on slippery surfaces. Do
not wear loose fitting clothing, short pants, sandals, or
go barefoot. Do not wear jewelry of any kind. They can
be caught in moving parts.
Don’t overreach – Keep proper footing and balance at all
times. Overreaching can result in loss of balance.
Do not leave the mower unattended while running or with
the start key installed.
Keep hands and feet away from cutting area. Keep clear
of the discharge opening at all times.
Operate the lawn mower only in daylight or good artificial
light.
Use safety glasses – Always wear eye protection with
side shields marked to comply with ANSI Z87.1. Use face
mask if operation is dusty.
Use the right appliance – Do not use the lawn mower for
any job except that for which it is intended.
Do not force the lawn mower – It will do the job better
and safer at the rate for which it was designed.
Do not charge batteries in rain, or in wet locations.
Stay alert – Watch what you are doing and use common
sense when operating the lawn mower. Do not operate
the mower while tired, upset, or under the influence of
drugs, alcohol, or medication. A moment of inattention
while operating the lawn mower may result in serious
personal injury.
Maintain lawn mower with care – Keep machine in good
working condition. Keep blades sharp and guards in place
and in working order. Replace damaged or unevenly worn
blades before using mower for best performance.
Check all nuts, bolts, and screws at frequent intervals for
proper tightness to be sure the equipment is in safe work-
ing condition. Mower blades are sharp. Wrap the blade or
wear gloves, and use extra caution when servicing them.
Do not dispose of the battery in a fire. The cell may
explode. Check with local codes for possible special
disposal instructions.
Stop the motor, wait until the blade comes to a complete
stop, and remove the start key and battery pack before
performing any maintenance, cleaning the lawn mower,
removing the grass catcher, or removing the mulching
plug.
Never use a hose, water, or any liquids to clean or
rinse off the lawn mower. Corrosive liquids, water, fer-
tilizers, and chemicals used to treat lawns can enter the
lawn mower and/or battery compartment and damage
electronic components and/or the battery pack, which can
result in a short circuit, increased risk of fire, and serious
personal injury. Remove any buildup of grass and leaves
on or around the mower housing and/or underneath the
mower deck. Wipe the mower clean with a dry cloth oc-
casionally.
Replace blade if it is bent or cracked. An unbalanced
blade causes vibration that could damage the motor drive
unit or cause personal injury. Sharpen a dull blade equally
at each end to maintain the balance. Mount a nail that
is perfectly horizontal and level, allowing enough room
above and below the nail for the blade to rotate freely
without striking any surface. Clean the blade thoroughly
and check its balance by supporting it horizontally on
the nail through its center hole. If either end of the blade
rotates downward, remove some metal by sharpening it
more on the heavier side until the blade is balanced. It is
balanced when neither end drops.
Always use safety protective devices. Do not operate the
mower without the entire grass catcher or mulching plug
and rear discharge door in place and working properly.
Do not open or mutilate the battery. Released electrolyte
is corrosive and may cause damage to the eyes or skin.
It may be toxic if swallowed.
Follow manufacturer’s instructions for proper operation
and installation of accessories. Only use accessories
approved by the manufacturer.
Exercise care in handling batteries in order not to short the
battery with conducting materials such as rings, bracelets,
IMPORTANT SAFETY INSTRUCTIONS
3 — English
IMPORTANT SAFETY INSTRUCTIONS
and keys. The battery or conductor may overheat and
cause burns.
Clear the work area before each use. Remove all objects
such as rocks, tree nuts, sticks, metal, wire, bones, toys,
or other objects which can be thrown by the blade.Stay
behind the handle when the motor is running.
Prevent unintentional starting. Ensure the switch is in the
off-position before connecting to battery pack, picking
up or carrying the appliance. Carrying the appliance with
your finger on the switch or energizing appliance that have
the switch on invites accidents.
When battery pack is not in use, keep it away from other
metal objects, like paper clips, coins, keys, nails, screws
or other small metal objects, that can make a connec-
tion from one terminal to another. Shorting the battery
terminals together may cause burns or a fire.
Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally occurs,
flush with water. If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may cause
irritation or burns.
Do not use a battery pack or appliance that is damaged
or modified. Damaged or modified batteries may exhibit
unpredictable behavior resulting in fire, explosion or risk
of injury.
Do not expose a battery pack or appliance to fire or
excessive temperature. Exposure to fire or temperature
above 265°F may cause explosion.
Follow all charging instructions and do not charge the
battery pack or appliance outside of the temperature
range specified in the instructions. Charging improperly
or at temperatures outside of the specified range may
damage the battery and increase the risk of fire.
Do not modify or attempt to repair the appliance or the
battery pack (as applicable) except as indicated in the
instructions for use and care.
Avoid holes, ruts, bumps, rocks, property stakes, or other
hidden objects. Uneven terrain could cause a slip and fall
accident.
Do not mow near drop-offs, ditches, or embankments.
Mow across the face of slopes, never up and down.
Exercise extreme caution when changing direction on
slopes.
Plan your mowing pattern to avoid discharge of material
toward roads, sidewalks, bystanders and the like. Also,
avoid discharging material against a wall or obstruction,
which may cause the material to ricochet back toward
the operator.
Do not mow on wet grass or excessively steep slopes.
Poor footing could cause a slip and fall accident. Walk,
never run.
Use extra care when approaching blind corners, shrubs,
trees, or other objects that may block your view.
Do not pull the mower backward unless absolutely nec-
essary. If you must back the mower away from a wall or
obstruction, first look down and behind to avoid tripping
or pulling the mower over your feet.
Never direct discharged material toward anyone. Avoid
discharging material against a wall or obstruction. Material
may ricochet back toward the operator. Stop the blade
when crossing gravel surfaces.
Objects struck by the lawn mower blade can cause severe
injuries to persons. The lawn should always be carefully
examined and cleared of all objects prior to each mowing.
If the lawn mower strikes a foreign object, follow these
steps:
Stop the lawn mower by releasing the blade control
lever, wait until the blade comes to a complete stop,
and then remove start key.
Thoroughly inspect the mower for any damage.
Replace the blade if it is damaged in any way. Repair
any damage before restarting and continuing to operate
the mower.
Stop the motor, wait until the blade comes to a complete
stop, and remove start key before unclogging the chute.
The cutting blade continues to rotate for a few seconds
after the motor is shut off. Never place any part of the
body in the blade area until you are sure the blade has
stopped rotating.
If the mower should start to vibrate abnormally, stop the
motor, remove the start key, and check immediately for
the cause. Replace the blade if it is unevenly worn or
damaged in any way. Vibration is generally a warning of
trouble.
Service on the product must be performed by qualified
repair personnel only. Service or maintenance performed
by unqualified personnel could result in injury to the user
or damage to the product.
The grass catcher assembly is subject to deterioration
and wear and should be checked each time the mower is
used. If replacement is needed, make sure the new grass
catcher meets original manufacturer’s recommendations
and specifications.
Use only authorized replacement parts when servicing
the product. Use identical replacement blades only. Use
of unauthorized parts may create a risk of serious injury
to the user, or damage to the product.

Maintain or replace safety instructions labels, as necessary.
Disconnect battery and remove start key. Disconnect
battery pack and remove start key from the appliance
before storing, servicing, or changing accessories such
as blades. Such preventive safety measures reduce the
risk of starting the tool accidentally.
Stop the unit and disconnect battery pack and start key
when not in use. Carry or push the unit with the motor
stopped and the start key removed from the mower.
4 — English
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL MEANING
DANGER: Indicates a hazardous situation, which, if not avoided, will result in death or
serious injury.
WARNING: Indicates a hazardous situation, which, if not avoided, could result in death or
serious injury.
CAUTION: Indicates a hazardous situation, that, if not avoided, may result in minor or
moderate injury.
NOTICE: (Without Safety Alert Symbol) Indicates information considered important, but
not related to a potential injury (e.g. messages relating to property damage).
IMPORTANT SAFETY INSTRUCTIONS
Battery tools do not have to be plugged into an electrical
outlet; therefore, they are always in operating condition.
Be aware of possible hazards when not using your bat-
tery tool or when changing accessories. Following this
rule will reduce the risk of electric shock, fire, or serious
personal injury.
Do not use battery-operated appliance in rain.
Remove or disconnect battery before servicing, cleaning
or removing material from the gardening appliance.
Use this product only with batteries and chargers listed in
tool/appliance/battery pack/charger correlation supple-
ment 988000-842.
Store idle lawn mower indoors – When not in use, mower
should be stored indoors in a dry, locked place out of the
reach of children. The start key and battery packs should
also be removed and stored in a separate location out of
the reach of children.
Follow instructions for lubricating and changing
accessories.
Only allow responsible adults, who are familiar with the
instructions, to operate this machine.
Never operate machine in a closed area.
Never tamper with safety devices. Check for proper op-
eration regularly.
Do not store battery packs or lawn mower in locations
where the temperature is less than 50°F or more than
100°F. Do not store outside or in vehicles.
Do not use lawn mower in locations where the temperature
is less than 40°F or more than 104°F.
Save these instructions. Refer to them frequently and
use them to instruct others who may use this product. If
you loan someone this tool, loan them these instructions
also.
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
Safety Alert Indicates a potential personal injury hazard.
Read Operator’s Manual To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Eye Protection Always wear eye protection with side shields marked to comply
with ANSI Z87.1.
Wet Conditions Alert
Risk of fire and burns. Do not expose battery, battery compartment,
or electronic components to rain, water, or liquids. Close cover
during use. Do not operate on wet ground.
5 — English
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
Electric Shock Failure to use in dry conditions and to observe safe practices can
result in electric shock.
Keep Hands and Feet Away Keep hands and feet away from blade and cutting area.
No Reach Do not reach hands or feet under mower deck.
Max 15°
No Slope Do not operate on inclines greater than 15º. Mow across the face
of slopes, never up and down.
Keep Children and
Bystanders Away Keep all children and bystanders at least 100 ft. away.
Ricochet Thrown objects can ricochet and result in personal injury or
property damage.
Recycle Symbol
This product uses lithium-ion (Li-ion) batteries. Local, state, or
federal laws may prohibit disposal of batteries in ordinary trash.
Consult your local waste authority for information regarding
available recycling and/or disposal options.
Direct Current Type or a characteristic of current
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
W Watt Power
hrs Hours Time
SYMBOLS
6 — English
PRODUCT SPECIFICATIONS
Motor ...................................................................................................................................................................... 40 Volt DC
Deck Size ....................................................................................................................................................................... 21 in.
Height Adjustments ........................................................................................................................................... 1.5 in. to 4 in.
Wheel Size ..............................................................................................................................................8 in. front, 10 in. rear
FEATURES
KNOW YOUR LAWN MOWER
See Figure 1.
The safe use of this product requires an understanding of
the information on the product and in this operator’s manual
as well as a knowledge of the project you are attempting.
Before use of this product, familiarize yourself with all op-
erating features and safety rules.
2-POSITION HANDLE
The handle can be adjusted to two heights for mowing.
BATTERY COVER
The battery cover protects the battery port from moisture
and debris.
CRUISE CONTROL
The cruise control button allows you to set the speed of the
mower to accommodate your pace when the self-propelled
feature is engaged.
DUAL BATTERY PORTS
This product features dual battery ports to maximize runtime
and minimize down time during operation. This enables the
user to easily switch batteries during a mowing session.
GRASS CATCHER
The grass catcher collects grass clippings and prevents
them from being discharged across your lawn as you mow.
NOTE: Mower will not start without the grass catcher or
mulch plug attached.
HEIGHT ADJUSTMENT HANDLE
The height adjustment handle provides cutting height
adjustments.
LED HEADLIGHTS
LED headlights are located on the front of the unit to illumi-
nate your path in low light conditions. The lights will operate
continuously whenever the motor is running.
NOTE: If the start button is pressed and released, the head-
lights will illuminate for 20 seconds.
MULCHING PLUG
When installed, the mulching plug covers the rear discharge
opening and allows the mower blade to cut and recut for
finer clippings.
ONE TOUCH HANDLE FOLDING
Pull the lever on the handle crossbar in either direction to
unlock the handles for folding.
SELF-PROPELLED FEATURE
Pulling the levers upward to meet the handle turns on the
self-propelled feature of your mower.
SIDE DISCHARGE CHUTE
The side discharge chute directs the clippings out of the
mower deck when the grass is too tall for mulching.
START BUTTON AND BAIL
The start button and bail are located on the upper handle of
the mower. Engage the bail then depress the start button to
start the motor and blade. Release the bail to stop the motor.
NOTE: The motor and blade will also start if the bail is en-
gaged first and the start button is pressed afterwards.
START KEY
The start key must be inserted before the mower can be
started.
TILT SENSOR
The tilt sensor prevents the unit from starting if it is in a verti-
cal position or tilted at an angle greater than 45º.
VERTICAL STORAGE CAPABILITY
The folding handles allow for compact, upright storage in
your garage.
7 — English
ASSEMBLY
UNPACKING
This product requires assembly.
Carefully remove the product and any accessories from
the box. Make sure that all items listed in the Packing
List are included.
WARNING:
Do not use this product if any parts on the Packing List
are already assembled to your product when you unpack
it. Parts on this list are not assembled to the product by
the manufacturer and require customer installation. Use
of a product that may have been improperly assembled
could result in serious personal injury.
Inspect the product carefully to make sure no breakage
or damage occurred during shipping.
Do not discard the packing material until you have care-
fully inspected and satisfactorily operated the product.
If any parts are damaged or missing, please call
1-800-525-2579 for assistance.
PACKING LIST
Lawn Mower
Start Key
Grass Catcher Bag and Frame
Mulching Plug
Side Discharge Chute
Operator’s Manual
WARNING:
If any parts are damaged or missing, do not operate this
product until the parts are replaced. Use of this product
with damaged or missing parts could result in serious
personal injury.
WARNING:
Do not attempt to modify this product or create acces-
sories not recommended for use with this product. Any
such alteration or modification is misuse and could result
in a hazardous condition leading to possible serious
personal injury.
WARNING:
Do not insert start key or battery packs until assembly is
complete and you are ready to mow. Failure to comply
could result in accidental starting and possible serious
personal injury.
WARNING:
To prevent accidental starting, do not make any adjust-
ments or installations with the start key or battery packs
inserted. Accidental starting of the mower during assem-
bly could result in serious personal injury.
WARNING:
Never operate the mower without the proper safety de-
vices in place and working. Never operate the mower with
damaged safety devices. Operating the mower with miss-
ing or damaged parts can result in serious personal injury.
UNFOLDING AND ADJUSTING THE HANDLE
ASSEMBLY
See Figures 2 - 3.
NOTICE:
Do not allow the starter cable to become pinched or
trapped when raising the handle.
To raise the handle:
Pull the lever on the handle crossbar to unlock the handle.
Moving the lever in either direction will unlock the handle.
Raise the handle to desired position.
Lock handle into place in either of the two notches on
the handle brackets.
NOTE: Handle can be adjusted to two heights for mow-
ing.
To lower the handle:

Lift the lever located on the crossbar in either direction
to fold the handle.
ASSEMBLING THE GRASS CATCHER
See Figures 4 - 5.
Place the grass catcher frame on a flat surface with the
handle facing down.
Orient the grass catcher bag so the vinyl floor is facing
up, then slide the bag onto the frame. When installing,
allow the frame handle to remain outside the bag and
make sure the bag seams are located at the frame edges.
Pull the clip over the frame rail to secure in place.
Lift the bag’s vinyl floor to the top of the frame rail and
secure in place.
Using the same method, attach the remaining clips on
each side of the bag to the frame rail to secure.
8 — English
ASSEMBLY
WARNING:
Do not allow familiarity with products to make you care-
less. Remember that a careless fraction of a second is
sufficient to inflict serious injury.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes resulting in possible
serious injury.
WARNING:
Do not use any attachments or accessories not recom-
mended by the manufacturer of this product. The use of
attachments or accessories not recommended can result
in serious personal injury.
WARNING:
Always inspect mower for missing or damaged parts and
blades for damage, uneven, or excessive wear prior to
use. Use of the mower with damaged or missing parts
can result in serious personal injury.
OPERATION
INSTALLING THE GRASS CATCHER (FOR
REAR BAGGING OPERATION)
See Figures 6.
NOTE: When using the grass catcher, do not install the
mulching plug.
Remove start key and battery packs.
Lift the rear discharge door.
Lift the grass catcher by its handle and place under the
rear discharge door so that the hooks on the grass catcher
are seated onto the slots on the mower housing.
Release the rear discharge door.
Reinstall start key and battery packs when you are ready
to mow.
INSTALLING THE MULCHING PLUG
(FOR MULCHING OPERATION)
See Figure 7.
NOTE: When using the mulching plug, do not install the
grass catcher.
Remove start key and battery packs.
Lift and hold the rear discharge door.
Grasp the mulching plug by its handle and insert it at a
slight angle, as shown.
Push the mulching plug securely into place. The tabs on
the mulching plug should be seated in the slots at the
bottom of the rear discharge opening, and the slot on the
mulching plug should go over the tab in the center of the
discharge opening.
Lower the rear discharge door.
Reinstall start key and battery packs when you are ready
to mow.
INSTALLING THE SIDE DISCHARGE CHUTE
See Figure 8.
The mower comes prepared for mulching with the spring-
loaded mulching cover already in place. If side discharge is
desired, install the side discharge chute.
Remove start key and battery pack.
Lift and hold the mulching cover.
Insert the side discharge chute as shown, aligning the
two notches with the tabs on each side of the mulching
cover.
Lower the mulching cover until the tabs are seated into
the notches on the side discharge chute.
Reinstall start key and battery pack when you are ready
to mow.
SETTING BLADE HEIGHT
See Figure 9.
When shipped, the blade on the mower is set to a low- cutting
position. Before using the mower for the first time, raise the
cutting position to the height best suited for your lawn. The
average lawn should be between 1-1/2 in. to 2 in. during cool
months and between 2 in. and 3-1/4 in. during hot months.
To adjust the blade height:
Remove the start key and battery packs.
To raise the blade height, grasp the height adjustment
handle and move it toward the back of the mower.
NOTE: Use the scale on top of the mower deck to select
the appropriate blade height.
To lower the blade height, grasp the height adjustment
handle and move it toward the front of the mower.
Reinstall the start key and battery packs when you are
ready to mow.
9 — English
WARNING:
Always remove battery packs and start key from your tool
when you are assembling parts, making adjustments,
cleaning, or when not in use. Following these instructions
will prevent accidental starting that could cause serious
personal injury.
NOTICE:
Before each use, inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts, caps,
etc. Tighten securely all fasteners and caps and do not
operate this product until all missing or damaged parts
are replaced. Please contact customer service or an
authorized service center for assistance.
APPLICATIONS
You may use this product for the purpose listed below:
Mowing your lawn
WARNING:
With the exception of using the self-propelled feature to
relocate the mower to the mowing site, always remove
battery packs and start key when moving or transporting
the mower to avoid accidental starting that could result
in serious personal injury.
INSTALLING/REMOVING BATTERY PACKS
See Figure 10.
Raise the battery cover.
Align raised ribs on battery packs with grooves in the
battery port and install the battery packs into the mower.
Repeat steps for second battery.
WARNING:
Make sure the latch on the bottom of the battery packs
snaps in place and the battery packs is fully seated and
secure in the mower’s battery port before beginning op-
eration. Failure to securely seat the battery packs could
cause the battery packs to fall out, resulting in serious
personal injury.
Lower the battery cover and make sure it is securely
closed.
To remove battery packs:
Raise the battery cover.
Press and hold the battery latch button at the bottom of
the battery pack.
Remove battery pack from the mower.
Repeat steps for second battery.
Lower the battery cover and make sure it is securely
closed.
For complete charging instructions, refer to the Operator’s
Manuals for your battery packs and charger models.
WARNING:
To avoid accidental starting that could result in serious
personal injury, always remove the start key when moving
or transporting the mower.
DUAL BATTERY PORTS
See Figures 10 - 11.
The mower is equipped with dual battery ports which enables
the user to easily switch batteries during a mowing session.
Raise the battery cover.
Remove the key and rotate it 180°.
Reinsert the key.
The arrow on the key points to the battery in use.
STARTING/STOPPING THE MOWER
See Figures 10 - 12.
NOTE: Mower will not start without the start key installed,
and the battery in the unit.
Unfold the handle assembly by lifting the lever on the
handle crossbar.
NOTE: The mower will not start if the handle assembly
is not in the operating position.
Raise the battery cover.
Install the battery packs into the battery port.
Insert the start key into the slot between the batteries in
the battery port.
NOTE: Arrow should be pointed toward the battery to be
used.
Lower the battery cover and make sure it is securely
closed.
Pull the bail toward the handle. Press and release the
start button to start the motor and blade.
  NOTE: The blade will also start if the start button is pressed
first and the bail is pulled after.
To stop the mower, release the bail.
NOTE: The blade is disengaged each time the bail is
released.
OPERATION
10 — English
OPERATION
SELF-PROPELLED MOWING
See Figure 12.
WARNING:
Never engage the blade when transporting the mower
from one location to another. Only engage the blade by
pressing the start button when you are ready to mow.
Failure to follow these instructions can result in serious
personal injury.
Once the mower has been started, the self-propelled fea-
ture is engaged by pulling one or both of the self-propel
levers upward to meet the handle.
To disengage the self-propelled feature, release the self-
propel levers.
NOTE: The self-propelled levers can be used without
engaging the blade to power the mower from one location
to another. You must pull the bail and then one or both
self-propel levers to move the mower without engaging
the blade.
CRUISE CONTROL
See Figure 12.
WARNING:
Always adjust the cruise control before you engage the
blade. Adjusting the cruise control while mowing may
cause you to lose control and could result in serious injury
while the blade is operating.
WARNING:
When using the self-propelled feature, ensure that the
cruise control is set at a speed that you can comfort-
ably follow when walking behind the mower. You may
lose control of the mower if the cruise control is set at
a speed that is too fast for your walking pace. Release
the self-propel levers and bail if you cannot keep up
with the mower and adjust the cruise control as needed.
Failure to follow these instructions can result in serious
personal injury.
By sliding the cruise control button on the handle, you can
adjust the speed of the mower to accommodate your pace
when the self-propelled feature is engaged. When viewed
from the normal operating position, the cruise control button
is at minimum self propelled speed at the far left side and
is at the maximum self propelled speed at the far right side.
MOWING TIPS
WARNING:
Do not mow on wet grass, which can cause you to slip
and fall and result in possible serious personal injury.
NOTE: Fully charge battery before each use for optimal
runtime.
Make sure the lawn is clear of stones, tree nuts, sticks,
wires, and other objects that could damage the lawn mower
blade or motor. Do not mow over property stakes or other
metal posts. Such objects could damage the blade or be
accidentally thrown by the mower in any direction and
cause serious personal injury to the operator and others.
For a healthy lawn, always cut off one-third or less of the
total length of the grass.
When cutting heavy grass, reduce walking speed to allow
for more effective cutting and a proper discharge of the
clippings.
Do not cut wet grass. It will stick to the underside of the
deck and prevent proper bagging or mulching of grass
clippings.
New or thick grass may require a narrower cut or a higher
cutting height.
Clean the underside of the mower deck after each use
to remove grass clippings, leaves, dirt, and any other
accumulated debris.
NOTE: Always stop mower, allow blade to completely stop,
remove the start key and remove the battery packs from
the battery port before cleaning underneath the mower.
SLOPE OPERATION
See Figure 13.
WARNING:
Slopes are a major factor related to slip and fall accidents
that can result in severe injury. Operation on slopes re-
quires extra caution. If you feel uneasy on a slope, do not
mow it. For your safety, do not attempt to mow slopes
greater than 15 degrees and mow across the face of
slopes, not up and down.
Mow across the face of slopes, not up and down. Exercise
extreme caution when changing direction on slopes.
Watch for holes, ruts, rocks, hidden objects, or bumps
which can cause you to slip or trip. Tall grass can hide
obstacles. Remove all objects such as rocks, tree limbs,
etc., which could be tripped over or thrown by the blade.
Always be sure of your footing. A slip and fall can cause
serious personal injury. If you feel you are losing your bal-
ance, release the upper blade control lever immediately.
Do not mow near drop-offs, ditches, or embankments;
you could lose your footing or balance.
11 — English
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken, or
destroy plastic which can result in serious personal injury.
LUBRICATION
All of the bearings in this product are lubricated with a suf-
ficient amount of high grade lubricant for the life of the unit
under normal operating conditions. Therefore, no further
bearing lubrication is required.
WARNING:
Always protect hands by wearing heavy gloves and/or
wrapping the cutting edges of the blade with rags and
other material when performing blade maintenance. Con-
tact with the blade could result in serious personal injury.
REPLACING THE CUTTING BLADE
See Figures 15 - 16.
NOTE: Only use authorized replacement blade.
Stop the motor and remove the start key. Allow the blade
to come to a complete stop.
Remove the battery packs from the battery port.
Turn the mower on its side.
Wedge a block of wood between the blade and mower
deck to prevent the blade from turning.
Loosen the blade nut by turning it counterclockwise (as
viewed from bottom of mower) using a 15 mm wrench
or socket (not provided).
Remove the blade nut, spacer, blade insulator, and blade.
Do not remove the hub or the adaptor.
WARNING:
Before performing any maintenance or cleaning the lawn
mower, make sure the mower blade comes to a complete
stop and the batteries and start key are removed to avoid
accidental starting and possible serious personal injury.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes resulting in possible
serious injury.
WARNING:
When servicing, use only identical replacement parts.
Use of any other parts can create a hazard or cause
product damage.
WARNING:
Never use a hose, water, or any liquids to clean or
rinse off the lawn mower. Corrosive liquids, water, fer-
tilizers, and chemicals used to treat lawns can enter the
lawn mower and/or battery compartment and damage
electronic components and/or the battery packs, which
can result in a short circuit, increased risk of fire, and
serious personal injury. Remove any buildup of grass
and leaves on or around the mower housing and/or un-
derneath the mower deck. Wipe the mower clean with a
dry cloth occasionally.
NOTICE:
Periodically inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts, caps,
etc. Tighten securely all fasteners and caps and do not
operate this product until all missing or damaged parts
are replaced. Please contact customer service or an
authorized service center for assistance.
MAINTENANCE
EMPTYING THE GRASS CATCHER
See Figure 14.
Stop the mower and allow the blade to completely stop.
Open the battery cover.
Remove the start key and battery packs from the battery
port.
Lift the rear discharge door.
OPERATION
Lift the grass catcher by its handle to remove from mower.
Empty grass clippings.
Reinstall the grass catcher as described earlier in this
manual.
Release the rear discharge door.
Reinstall the start key and battery packs when you are
ready to mow.
12 — English
MAINTENANCE
STORING THE MOWER
See Figures 17 - 18.
WARNING:
Remove all battery packs from the battery ports and start
key and store indoors in a secure and dry location out of
the reach of children to prevent unauthorized use of the
lawn mower and possible serious personal injury.
Before storage, wipe any dirt or debris from the battery
area.
Raise the mower into the vertical storage position and
clean grass clippings that have accumulated on the un-
derside of the mower deck.
Wipe the mower clean with a dry cloth.
Check all nuts, bolts, knobs, screws, fasteners, etc., for
tightness.
Inspect moving parts for damage, breakage, and wear.
Have repairs made on any damaged or missing parts.
Check blade for damage, uneven, or excessive wear and
replace blade if these conditions exist.
Store mower indoors in a clean, dry place out of the reach
of children.
To store the mower in a horizontal position, lower the
handle assembly. Avoid pinching or trapping any cables.
To store the mower in a vertical position, remove the
grass bag, then lower the handle assembly. Avoid
pinching or trapping any cables. Raise the mower 90°
to rest on its rear support.
NOTICE:
Do not allow the starter cable to become pinched or
trapped when lowering the handle.
Do not store near corrosive materials such as fertilizer or
rock salt.
WARNING:
If the hub and/or the adaptor have been removed, replace
them before placing blade on the shaft. Failure to do so
could cause the blade to detach or become unbalanced
since blade will not tighten properly, which can result in
serious personal injury.
Place the new blade on the shaft against the blade posts
on the hub. Ensure blade is properly seated with shaft go-
ing through center blade hole and the two blade posts on
the hub inserted into their respective holes on the blade.
Make sure it is installed with the curved ends pointing up
toward the mower deck and not down toward the ground.
When seated properly, the blade should be flat.
Replace the blade insulator and spacer, then thread the
blade nut on the shaft and finger tighten.
NOTE: Make certain all parts are replaced in the exact
order in which they were removed.
Torque the blade nut down clockwise using a torque
wrench (not provided) to ensure the bolt is properly
tightened. The recommended torque for the blade nut is
325 – 400 in.lbs.
WARNING:
Ensure blade is properly seated and the blade nut is
tightened to the torque specifications above. Failure to
properly attach the blade could cause it to come loose
and result in possible serious personal injury.
13 — English
TROUBLESHOOTING
IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTACT YOUR AUTHORIZED SERVICE DEALER.
PROBLEM POSSIBLE CAUSE SOLUTION
Handle not in position. Handle adjustment pins are not in place. Pull up handle adjustment lever, release,
and make sure handle adjustment pins
lock into place.
Mower not starting. Battery is low in charge.
Start key not installed.
Handle assembly is not in operating
position.
Charge the battery.
Install start key.
Raise lower and upper handle.
Mower cutting grass unevenly. Lawn is rough or cutting height not set
properly.
Adjust the cutting height.
Mower not mulching properly. Wet grass clippings sticking to the un-
derside of the deck.
Wait until the grass dries before mowing.
Mower hard to push. High grass, rear of mower housing and
blade dragging in heavy grass, or cut-
ting height too low.
Raise cutting height.
Mower not bagging properly. Cutting height set too low.
Grass blocking rear chute of mower.
Raise cutting height.
Stop the motor, remove start key, and
battery. Remove grass catcher bag and
remove the blockage.
Mower vibrating at higher speed. Blade is unbalanced, excessively or
unevenly worn.
Bent motor shaft.
Replace the blade.
Stop the motor, remove start key, and
battery. Inspect for damage. Have re-
paired by an authorized service center
before restarting.
Motor stops while cutting. Cutting height set too low. Raise the cutting height.
This product has a Five-year Limited Warranty for personal,
family, or household use (90 days for business or commercial use).
For warranty details, visit www.ryobitools.com
or call (toll free) 1-800-525-2579.
MAKE THE MOST OF YOUR PURCHASE!
Go to http://register.ryobitools.com and register your new tool on-line.
Your product has been fully tested prior to shipment
to ensure your complete satisfaction.
For any questions about operating or maintaining
your product, call the RYOBI Help Line!
1-800-525-2579
2 — Français
AVERTISSEMENT :
LISEZ ET VEILLEZ À COMPRENDRE TOUTES LES
INSTRUCTIONS. Le non respect des instructions
énumérées ci-dessous et sur la machine pourrait résulter
en un choc électrique, un incendie, et/ou des blessures
sérieuses.
LIRE TOUTES LES INSTRUCTIONS
Cet outil coupant est capable d’amputer des mains et des
pieds et projeter des objets. Le non respect de toutes les
instructions de sécurité pourrait résulter en des blessures
graves ou la mort.
Éviter les environnements dangereux – N’utilisez pas la
tondeuse dans un environnement mouillé ou humide et
ne l’utilisez pas durant la pluie.
Garder les enfants à l’écart – Garder les badauds, enfants
et animaux domestiques à une distance minimum de 30,5
m (100 pi). Arrêter la machine si quelqu’un entre dans la
zone.
Des accidents tragiques peuvent survenir si l’opérateur n’est
pas conscient de la présence des enfants. Les enfants sont
souvent attirés pas la machine et l’activité de tondaison.
Ne prenez jamais pour acquis que les enfants resteront à
l’endroit où vous les avez vus la dernière fois.
Assurez-vous que les enfants soient éloignés de la zone
de coupe et qu’ils soient supervisés par un adulte autre
que l’opérateur.
Soyez vigilant et éteignez la tondeuse si un enfant
s’approche.
Ne permettez jamais à des enfants d’utiliser la machine.
Redoublez la prudence quand vous vous approchez des
coins, des arbustes, des arbres ou d’autres objets qui
peuvent masquer la présence d’un enfant.
Porter une tenue appropriée – Porter des pantalons
longs, manches longues, des gants épais et des souliers
de protection qui protègeront vos pieds et amélioreront
votre équilibre sur des surfaces glissantes. Ne pas porter
de vêtements amples, bijoux, shorts, sandales et ne pas
travailler pieds nus. Ne porter aucun bijou. Ils peuvent être
pris dans les parties en mouvement.
Ne pas travailler hors de portée – Toujours se tenir bien
campé et en équilibre. Le travail hors de portée risque de
faire perdre l’équilibre.
Ne laissez pas la tondeuse sans surveillance quand elle
est allumée ou une fois la clé de démarrage fixée.
Éloignez les mains et les pieds de la zone de coupe. Tenez
vous éloigné de l’ouverture de décharge en tout temps.
Utilisez la tondeuse seulement à la lumière du jour ou avec
une bonne lumière artificielle.
Porter des lunettes de sécurité – Toujours porter une
protection oculaire munie d’écrans latéraux certifiée
conforme à la norme ANSI Z87.1. Utilisez une masque
faciale si l’utilisation produit de la poussière.
Utilisez l’outil approprié – N’utilisez pas la tondeuse pour
aucune tâche sauf celle pour laquelle elle est conçue.
Ne forcez pas la tondeuse – Elle exécutera le travail mieux
et de façon plus sécuritaire à la vitesse pour laquelle elle
fut conçue.
Ne pas charger le bloc-pile sous la pluie ou dans un endroit
mouillé.
Restez vigilant – Regardez ce que vous faites et utilisez
votre meilleur jugement lorsque vous utilisez la tondeuse.
N’utilisez pas la tondeuse si vous êtes fatigué, contrarié ou
sous influence de drogues, d’alcool ou de médicaments. Un
moment d’inattention pendant l’utilisation de la tondeuse
peut résulter en une blessure grave.
Faire l’entretien de la tondeuse avec soins – Gardez l’outil
en bon état. Assurez-vous que les lames soient affûtées et
que les dispositifs de protections soient en place et en état
de fonctionnement. Remplacer les lames endommagées
ou usées de façon inégale avant d’utiliser la tondeuse
d’obtenir un rendement optimal.
Vérifiez fréquemment si tous les écrous, boulons et vis sont
serrés pour s’assurer que l’équipement est sécuritaire. Les
lames de tondeuse sont tranchantes. Envelopper la lame
ou porter des gants et prendre beaucoup de précautions
lors de l’entretien.
Ne pas jeter le pile au feu. La cellule peut exploser. Vérifier
les codes locaux pour connaître toute instruction spéciale
relative à l’élimination des piles.
Arrêter le moteur, attendre que la lame s’arrête complètement
et retirer la clé de démarrage et bloc-piles avant de réparation
du produit, de nettoyer la tondeuse, d’enlever le collecteur
d’herbe ou retrait du capuchon du broyeur.
Ne jamais utiliser un boyau, de l’eau ou une autre liquide
pour nettoyer ou rincer la tondeuse. Les liquides corrosifs,
l’eau, l’engrais et les produits chimiques utilisés pour traiter
les pelouses peuvent s’infiltrer dans la tondeuse et/ou le
compartiment de la pile et endommager les composants
électroniques et/ou le bloc-pile, ce qui peut entraîner
un court-circuit, augmenter le risque d’incendie ou des
blessures corporelles graves. Enlever toute accumulation
d’herbes ou de feuilles sur ou autour du corp de la tondeuse
et/ou en dessous de la plateforme de la tondeuse. Essuyer
la tondeuse de temps en temps avec un linge sec.
Remplacer la lame si elle est pliée ou fissurée. Une
lame déséquilibrée provoque des vibrations qui peuvent
endommager le moteur de l’appareil et provoquer des
blessures. Affûter également les extrémités de la lame
émoussée afin de maintenir l’équilibre. Placer un clou,
parfaitement à une position parfaitement horizontale et au
niveau, en laissant suffisamment d’espace au-dessus et en
dessous du clou afin que la lame puisse tourner librement
sans heurter de surface. Nettoyer complètement la lame
et vérifier son équilibre en la déposant à l’horizontale
et en plaçant l’orifice du centre sur le clou. Si l’une des
extrémistes de la lame tourne vers le bas, retirer certains
métaux en l’aiguisant davantage sur le côté le plus lourd
INSTRUCTIONS IMPORTANTES CONCERNANT LA SÉCURITÉ
3 — Français
INSTRUCTIONS IMPORTANTES CONCERNANT LA SÉCURITÉ
jusqu’à ce que la lame soit équilibrée. Une lame équilibrée
lorsqu’aucune extrémité n’est inclinée.
Toujours, utiliser des dispositifs de protection. N’utilisez pas
la tondeuse sans le collecteur d’herbe ou le capuchon du
broyeur et porte arrière de décharge en place et fonctionne
correctement.
Ne pas ouvrir ou altérer le bloc-piles. L’électrolyte est un
produit corrosif pouvant causer des lésions cutanées ou
oculaires. Il peut être toxique en cas d’ingestion.
Suivez les instructions du fabricant relatives à l’installation
et l’utilisation des accessoires. Utilisez seulement des
accessoires approuvés par le fabricant.
Manipuler les batteries avec soin pour éviter des courts-
circuits avec des objets conducteurs comme des anneaux,
des bracelets et des clés. La batterie ou l’objet conducteur
peuvent surchauffer et causer des brûlures.
Nettoyez la zone de travail avant chaque utilisation.
Enlevez tous les objets tels que les roches, noix d’arbres,
les branches, métal, les fils, les os, les jouets et d’autres
objets qui peuvent être projetés par la lame. Restez en
arrière de la poignée quand le moteur est en marche.
Empêcher les démarrages accidentels. S’assurer que la
gâchette est en position d’arrêt avant d’insérer la bloc piles,
de le ramasser ou de le transporter. Le fait de transporter
un appareil en gardant le doigt sur la gâchette ou de mettre
sous tension un appareil lorsque la gâchette est en position
de marche favorise les accidents.
Lorsque le bloc de batteries n’est pas en usage, le garder
à l’écart d’articles tels qu’attaches trombones, pièces de
monnaie, clous, vis et autres petits objets métalliques
risquant d’établir le contact entre les deux bornes. Le
court-circuitage des bornes peut causer des brûlures ou
un incendie.
En cas d’usage abusif, du liquide peut s’échapper des
batteries. Éviter tout contact avec ce liquide. En cas de
contact accidentel, rincer immédiatement les parties
atteintes avec de l’eau. Si le liquide pénètre dans vos yeux,
il faut aussi consulter un médecin. Le liquide s’échappant
des batteries peut causer des irritations ou des brûlures.
Ne pas utiliser un bloc-piles ou un appareil endommagé ou
modifié. Le bris ou la modification du bloc-piles peut causer
un comportement imprévisible et causer un incendie, une
explosion ou des blessures.
Ne pas exposer le bloc-piles ou l’outil à un feu ou à des
températures excessives. Une exposition à un incendie
ou à une température supérieure à 130 °C (265 °F) peut
provoquer une explosion.
Suivre toutes les instructions afférentes à la recharge
et ne pas recharger le bloc-piles ou l’appareil hors des
températures spécifiées dans les instructions. Une recharge
incorrecte ou hors des températures spécifiées peut
endommager la pile et augmenter les risques de feu.
Ne modifiez pas ou n’essayez jamais de réparer l’appareil
ou le bloc de batterie (selon le cas), sauf comme indiqué
dans les instructions d’utilisation et d’entretien.
Évitez les trous, les ornières, les roches, bornes de propriété
ou d’autres objets cachés. Un terrain accidenté pourrait
provoquer un glissement et vous faire tomber par accident.

Ne tondez pas près des dépressions, fossés ou des berges.
Tondez les pentes dans le sens transversal, jamais en
montant ou en descendant. Soyez particulièrement prudent
lors des changements de direction sur les terrains en pente.
Planifiez le parcours de la tondeuse pour éviter d’éjecter
les matériaux sur les routes, les trottoirs, les passants, etc.
Évitez également d’éjecter les matériaux sur un mur ou
une obstruction ce qui pourrait causer un matériau d’être
projeté par ricochet en direction de l’opérateur.
Ne tondez pas l’herbe mouillée ou sur des pentes
excessivement raides. Une mauvaise position peut vous
faire glisser et tomber par accident. Marchez, ne courez
jamais.
Redoublez la prudence si vous vous approchez des coins,
des arbustes, des arbres ou d’autres objets qui vous cachent
la vue.
Ne tirez jamais la tondeuse vers l’arrière à moins que cela
soit absolument nécessaire. Si vous devez tirer la tondeuse
pour éviter un mur ou une obstruction, commencez par
regarder en bas et en arrière pour ne pas trébucher o
tirando la podadora hacia los pies.
N’éjectez jamais du matériel en direction de quelqu’un.
Évitez d’éjecter le matériel sur un mur ou une obstruction.
Le matériel pourrait être projeté par ricochet en direction
de l’opérateur. Arrêtez la lame quand vous traversez des
surfaces recouvertes de gravier.
Des objets frappés par la lame de la tondeuse peuvent
causer des sérieuses blessures. La pelouse devrait toujours
être examinée attentivement et nettoyée de tout objet avant
la tondaison.
Si la tondeuse frappe un objet étranger, suivez ces étapes:
Arrêter la tondeuse en relachant l’levier de commande
de la lame, attendre que la lame s’arrête complètement,
puis retirer la clé de démarrage.
Inspectez attentivement la tondeuse pour desceller les
dommages.
Remplacer la lame si elle est endommagée de quelque
façon que ce soit Réparez tout dommage avant de
démarrer et de continuer à utiliser la tondeuse.
Arrêter le moteur, attendre que la lame s’arrête complètement
et retirer la clé de démarrage avant de déboucher la goulotte.
La lame continue de tourner pendant quelques secondes
après que le moteur soit arrêté. Ne mettez jamais aucune
partie du corps dans la proximité de la lame avant d’être
certain que la lame a cessé de tourner.
Si la tondeuse commence à vibrer de façon anormale,
arrêtez le moteur, retirer la clé de démarrage et vérifiez
immédiatement la cause. Remplacer la lame si elle est
4 — Français
Les termes de mise en garde suivants et leur signification ont pour but d’expliquer le degré de risques associé à
l’utilisation de ce produit.
SYMBOLE SIGNAL SIGNIFICATION
DANGER : Indique une situation dangereuse qui, si elle n’est pas évitée, aura pour
conséquences des blessures graves ou mortelles.
AVERTISSEMENT : Indique une situation dangereuse qui, si elle n’est pas évitée, pourrait entraîner
des blessures graves ou mortelles.
ATTENTION : Indique une situation dangereuse qui, si elle n’est pas évitée, pourraît entraîner
des blessures légères ou de gravité modérée.
AVIS :
(Sans symbole d’alerte de sécurité) Indique les informations jugées importantes
sans toutefois représenter un risque de blessure (ex. : messages concernant
les dommages matériels).
usée de façon inégale ou endommagée de quelque façon
que ce soit. La vibration est généralement un signe d’un
problème.
Le produit doit être réparé par un personnel qualifié
seulement. Des réparations ou l’entretien effectués par un
personnel non qualifié pourrait résulter en des blessures
pour l’utilisateur ou endommager le produit.
L’assemblage du collecteur d’herbe peut se détériorer et
s’user et doit être vérifier chaque fois avant d’utiliser la
tondeuse à gazon. S’il doit être remplacé, s’assurer que le
nouveau collecteur d’herbe répond aux exigences et aux
spécifications du fabricant d’origine.
Lors de réparation du produit, utilisez pièces de
remplacement autorisées. Utiliser uniquement des lames de
rechange identiques. L’utilisation des pièces non autorisées
peut créer un risque d’une blessure sérieuse à l’utilisateur
ou endommager le produit.
Conserver ou remplacer les étiquettes d’instructions de
sécurité, si nécessaire.
Débrancher la pile et retirer la clé de démarrage – Débrancher
le bloc-piles et retirer la clé de démarrage de l’appareil
avant de le ranger, le réparer ou changer les accessoires
tels que des lames. Ces mesures de sécurité réduisent les
risques de démarrage accidentel de l’outil.
Arrêter l’produit et retirer le bloc de piles et clé de démarrage
lorsqu’il n’est pas utilisé. Transporter ou pousser l’appareil
lorsque le moteur est arrêté et d’avoir retirer la clé de
démarrage de la tondeuse.
Les outils fonctionnant piles n’ayant pas besoin d’être
branchés sur une prise secteur, ils sont toujours en état
de fonctionnement. Tenir compte des dangers possibles
lorsque l’outil n’est pas en usage et lors du remplacement
des piles. Le respect de cette règle réduira les risques
d’incendie, de choc électrique et de blessures graves.
Ne pas utiliser un appareil alimenté par pile sous la pluie.
Retirer ou débrancher la pile avant l’entretien ou le nettoyage
de l’outil de jardin ou avant d’en retirer des matériaux.
Utiliser ce produit seulement avec la piles et le chargeurs
indiqués dans le supplément de raccordement pour
chargeur/outils/piles/appareil n˚ 988000-842.
Ranger les appareils qui ne sont pas utilisés à l’intérieur –
lorsque la tondeuse n’est pas utilisé, le ranger à l’intérieur
dans un endroit sec et verrouillé hors de la portée des
enfants. La clé de démarrage et les blocs-piles doivent
être retirés et rangés dans un autre endroit et hors de la
portée des enfants.
Suivre les instructions de lubrification et de changement
d’accessoires.
Faire fonctionner cet appareil ne doit être permis qu’aux
adultes responsables et familiers avec les instructions.
Ne jamais faire fonctionner l’appareil dans un endroit clos.
Ne jamais modifier les dispositifs de sécurité. Vérifier
périodiquement l’état de fonctionnement.
Ne pas ranger les blocs-piles ou la tondeuse dans des
endroits où la température est inférieure à 10 °C (50 °F) ou
supérieure à 38 °C (100 °F). Ne pas remiser à l’extérieur
ou dans un véhicule.
Ne pas utiliser la tondeuse dans des endroits où la
température est inférieure à 4 °C (40 °F) ou supérieure à
40 °C (104 °F).
Conserver ces instructions. Les consulter fréquemment et
les utiliser pour instruire les autres utilisateurs éventuels.
Si cet outil est prêté, il doit être accompagné de ces
instructions.
INSTRUCTIONS IMPORTANTES CONCERNANT LA SÉCURITÉ
SYMBOLES
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70

Ryobi RY401014 Manuel utilisateur

Catégorie
Tondeuses à gazon
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues