Dec. 2023
Phone (800) 526.2588
Fax (800) 526.2585
44 Harbor Park Drive
Port Washington, NY 11050
1600 Distribution Ct
Lithia Springs, GA 30122
1750 Archibald Avenue
Ontario, CA 91760
1
• Read all instructions before installing.
• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
•
• Retain installation instructions for future maintenance reference.
All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by dweLED. Substitution of parts or accessories not designated for use with this product by dweLED could
result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are
damaged or missing.
Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
• Lisez toutes les instructions avant l’installation.
• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits dweLED. Remplacer des pièces ou accessoires non conçus pour ce
produit dweLED pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez
contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
A
Wire Connector
Qty: 3 pcs +1 Extra
B
Wire Connector
Qty: 3pcs +1 Extra
Mounting Screw
Qty: 1 Extra
C
INSTALLATION INSTRUCTION
PD-59416
594-LED Pendant
Dec. 2023
Phone (800) 526.2588
Fax (800) 526.2585
44 Harbor Park Drive
Port Washington, NY 11050
1600 Distribution Ct
Lithia Springs, GA 30122
1750 Archibald Avenue
Ontario, CA 91760
2
INSTALLATION INSTRUCTION
PD-59416
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig.2 Wiring
Back Plate Dimensions
3500K
Switch
4000K2700K
3000K
Driver
Black - Hot
White - Neutral
Blue
Black
Brown
Green
White Black Output
Input
Black
Red
Canopy
Fig.3
Cable
594-LED Pendant
PREPARATION
1. Shut o-the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area.
Be careful not to lose any small parts necessary for installation.
MOUNTING THE FIFIXTURE (Fig. 1,4)
3. Loosen the mounting screw (C) from the xture, and remove the mounting plate.
4. Set color temperature at this stage. The xture can switch between four color
temperatures (2700K,3000K, 3500K,4000K), which can beadjusted to your preference
using the 4CCT switch (Fig. 4) mounted in the canopy.
Note: the switch comes with a detachable cover, remove the cover prior to
adjusting the color temperature, reattach the cover after adjustment is made.
5. Adjust the xture wire length by pushing the cable gripper on the canopy and
pulling the wire as desired.
a) Before securing the canopy in place, it is recommended to retract or extend the
wire within the canopy to a desirable length.
b) Due to limited space within the canopy, shorten the cable as necessary to make
the installation easier. Make sure to identify and label all the wiring properly before
any trimming/shortening (Fig. 3).
6. Secure the mounting back plate to the junction box using standard junction box screws
that comes with the junction box.
Note: (i) using any other non-original-manufacturer provided junction box screw may
result in safety issue;
(ii) The side of the mounting plate marked “GND” must face out.
CONNECTING THE WIRES (Fig. 2,3)
7. Connect the driver’s output wires to xture wire as shown in Fig. 3, black(cable) to
the red(driver), white(cable) to the brown(switch), green(cable) to the blue(switch),and black(switch) to
the black(driver),make sure that wire connectors (B) are secured. Then tuck them inside the canopy.
8. Connect the driver’s input wires to junction box wires as shown in Fig. 2, make sure that all wire
connectors (A) are secured. If your outlet box has a green or bare copper ground wire, connect
the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly to the
mounting plate using the screw provided. After wires are connected, tuck them carefully inside
the junction box.
COMPLETING THE INSTALLATION(Fig.1)
9. Secure the xture by mounting the canopy to the ring of the mounting plate. Turn and rotate the
canopy in the direction of the arrow until it stops. Fasten the canopy to the
mounting plate using the mounting screw (C).Finally tighten the conduti
Fig.4
4000K 3500K 3000K 2700K
Wire Connector
Mounting Screw
Lamp Body
Conduit
Junction Box
Ground Wire
A
C
Driver
Canopy
Mouting
back plate
Instruction:Adjust the xture
wire length by pushing the
cable gripper on the canopy
and pulling the wire as desired.
Push up
Cable gripper
Wire Connector
B
4CCT Switch
Junction
Box Screw
Switch Cover
Fig.1
-
1
-
2
dans d''autres langues
Documents connexes
-
WAC Lighting PD-81442 Mode d'emploi
-
-
-
-
-
-
-
-
-