WARN Works 4700 Manuel utilisateur

WINCH USER GUIDE

WARN Works® 4700 Utility Winch

Part Number: 604700, 64009

Your safety, and the safety of others, is very important. To help you make informed decisions about safety, we have provided

installation and operating instructions and other information on labels and in this guide. This information alerts you to potential hazards

that could hurt you or others. It is not possible to warn you about all potential hazards associated with this product, you must use your

own good judgment.

CARELESS WINCH INSTALLATION AND OPERATION CAN RESULT IN SERIOUS INJURY OR EQUIPMENT DAMAGE. READ

AND UNDERSTAND ALL SAFETY PRECAUTIONS AND OPERATING INSTRUCTIONS BEFORE INSTALLING AND OPERATING

THIS PRODUCT.

This guide identifies potential hazards and has important safety messages that help you and others avoid personal injury or death.

WARNING and CAUTION are signal words that identify the level of hazard. These signal words mean:

WARNING signals a hazard that

could

cause serious injury or death, if you do not follow recommendations.

CAUTION signals a hazard that

may

cause minor to moderate injury, if you do not follow recommendations.

This guide uses

NOTICE

to call attention to important mechanical information, and Note: to emphasize general information worthy of

special attention

PAGE 1 63998 Rev. C1

Product Description: WARN Works® 4700 Utiltiy Winch

The WARN Works® 4700 Utility Winch is a powerful; pulling tool. Powered by a 12 volt DC power source

this compact winch has a pulling capacity of 4700 pound / 2130 kilos.

The units has a 12’ remote control for power in and power out operation, 60’ of 1/4” wire rope and clasp

hook. A freespooliong clutch is a standard option.

Introduction

Thank you for choosing WARN Works® for your utility winch needs. All WARN Works® products have been

designed and manufactured for many years of problem-free operation. For future reference please record the

following information:

Model/Part Number: Date of Purchase:

Before you begin

 Read the instructions completely to familiarize yourself with the installation process.

PAGE 2 63998 Rev. C1

 Review all the notices, cautions and warnings to make sure the kit will be installed correctly and safely.

Saftey Precautions

The following are general safety precautions that evey winch operator should know. Taking precedence over

any specific rule listed here, however, is the most important rule of all—USE COMMON SENSE.

A few minutes spent reading these rules can make an operator aware of dangerous practices to avoid and

precautions to take for his own safety and the safety of others. Frequent examinations and periodic

inspections of the equipment as well as conscientious observance of safety rules may save lives as well as

time and money.

WARNING

MOVING PARTS ENTANGLEMENT HAZARD

Failure to observe these instructions could lead to severe injury or death.

To avoid injury to hands or fingers.

• Always keep hands clear of wire rope, hook loop, hook and fairlead opening during installation, operation and when

spooling in or out.

• Always use extreme caution when handling

hook and wire rope during spooling operations.

• Always use supplied hook strap whenever

spooling wire rope in or out, during installation or operation to avoid injury to hands or fingers.

WARNING

FALLING OR CRUSHING HAZARD

Failure to observe these instructions could lead to severe injury or death.

• Never use as an overhead hoist, or to suspend a load.

• Never use to lift or move persons.

PAGE 3 63998 Rev. C1

Saftey Precautions - continued

CAUTION

MOVING PARTS ENTANGLEMENT HAZARD

Failure to observe these instructions could lead to minor to moderate injury.

General Safety:

•Always Know Your Winch: Take time to fully read and understand the included Installation and Operations guide,

and Basic Guide to Winching Techniques, in order to understand your winch and the winching operation.

• Never operate this winch if you are under 16 years of age.

• Never operate this winch when under the

influence of drugs, alcohol or medication.

• Never exceed winch or wire rope rated capacity. Double line using a snatch block to reduce winch load.

Installation Safety:

• Always choose a mounting location that is

sufficiently strong to withstand the maximum

pulling capacity of your winch.

• Always use factory approved switches, remote controls, accessories and installation components.

• Always use grade 5 or better hardware, never weld bolts and never use longer bolts than those supplied from

factory.

• Always complete winch mounting and attachment of hook to hook loop before wiring winch during installation.

• Always position fairlead with WARNING label on top.

• Always spool the wire rope onto the drum as

indicated by the drum rotation label on the winch. Required for automatic brake to work (if winch is so equipped) and

for correct installation orientation.

• Always prestretch wire rope and respool under load before use. Tightly wound wire rope reduces chances of

"binding", which is wire rope working it's way down into a loosely wound wire rope layer, and catching or damaging

itself.

Winching Safety:

•Always inspect winch installation and wire rope and hook condition before operating winch. Frayed, kinked or

damaged wire rope must be replaced immediately. Loose or damaged winch installation must be corrected

immediately.

• Never hook wire rope back onto itself. This damages the wire rope. Always use a choker chain, wire choker rope or

tree trunk protector on the anchor.

• Always prior to winching, remove any element

that may interfere with safe winch operation.

• Always take your time when rigging for a winch pull.

• Always be certain the anchor you select will withstand the load, and the strap or chain will not slip.

• Never engage or disengage clutch if winch is under load, wire rope is in tension or wire rope drum is moving

• Always unspool as much wire rope as possible when rigging. Double line or pick distant anchor point.

• Never winch with less than 5 wraps of wire rope around the drum, the wire rope could come loose from the drum.

• Always stand clear of wire rope and load during operation.

• Never touch wire rope or hook while in tension or under load.

• Never touch wire rope or hook while someone else is at the control switch or during winching operation.

• Never touch wire rope or hook while remote control is plugged into winch.

• Always stand clear of wire rope and load and keep others away while winching.

Always require operator and bystanders to be aware of stability during winching of vehicle and/or load.

• Always keep remote control lead clear of the drum, wire rope and rigging. Inspect for cracks, pinches, frayed wires

or loose connections. Replace if damaged.

PAGE 4 63998 Rev. C1

Saftey Precautions - continued

CAUTION

CUT AND BURN HAZARD

Failure to observe these instructions could lead to minor to moderate injury.

To avoid injury to hands and fingers:

• Always wear heavy leather gloves when handling a wire rope.

• Never let wire rope slip through your hands.

• Always be aware of possible hot surface at winch motor, drum or wire rope during or after winch use.

CAUTION

Moving Parts Entanglement Hazard

Failure to observe these instructions could lead to minor to moderate injury.

• Never apply load to hook tip or latch. Apply load only to the center of hook.

• Never use a hook whose throat opening has increased, or whose tip is bent or twisted.

NOTICE

AVOID WINCH AND EQUIPMENT DAMAGE

• Always avoid continuous side pulls, which can pile up wire rope at one end of the drum. This can damage your wire

rope or winch.

• Always ensure the clutch is fully engaged or Disengaged.

• Never use winch to tow other vehicles. Shock loads can momentarily exceed capacity of wire rope & winch

• Always use care to not damage your frame when anchoring your vehicle during a winching operation.

• Never "jog" wire rope under load. Shock loads can momentarily exceed capacity of wire rope and winch.

• Never use winch to secure a load during transport.

• Never submerge winch in water.

• Always store the winch in a protected, clean, dry area.

Partnumber & Cord ends for the Works 4700

PAGE 5 63998 Rev. C1

PART NUMBERS

604700 12v DC 4700# Utility Winch - US

64009 12v DC 4700# Utility Winch - International

Parts List

The WARN Works® 4700 Utility Winch consists of the following main components.

1. Works 4700 Winch Unit 2. Remote with 12’(3.7 m) Lead

3. Fairlead 4. 2 – 6’ (1.8 m) x 6 gauge cable

5. Latch Hook and Hook Strap 6. Mounting Hardware

PAGE 6 63998 Rev. C1

1

2

3

4

5

6

Specification Data for the Works 4700

FEATURES

Pulling Capacity 4700lbs. (2130 kg) Brake Dynamic and mechanical braking

Switch Type Remote with 12’(3.7 m)

Lead Warranty 1 year limited

Motor Permanent Magnet Wire Rope ¼”" X 60' (18.3 m)

HP 1.9 HP 3.0" Diameter Drum Diameter 2.5" (6.35 cm)

Power 12 volt DC Fairlead Roller

Gear Train 3-Stage planetary Hole Pattern 4 holes

Gear Ratio 216:1 Electrical Leads 2 – 6’ (1.8 m) x 6 gauge cable

Clutch Lever- Multi-directional Weight 42 lbs. (19.1 kg.)

Performance Data for the Works 4700

PERFORMANCE DATA: 4700

Load Current Speed Pulling Power by Wire Rope

Layer

Lbs. Kg Amps Ft/min M/min Layer lbs. kg

0 0 47 17.9 5.5 1 4700 2130

1000 453.6 82 12.8 3.9 2 3980 1800

2000 907.2 150 10.8 3.3 3 3450 1560

3000 1360.8 212 8.1 2.5 4 3041 1380

4000 1814.4 277 5.8 1.8 5 2720 1230

4700 2132 322 4.3 1.3

Dimensional Data for the Works 4700

PAGE 7 63998 Rev. C1

Winch Installation to fixed location

Caution

Winch Failure Hazard

Failure to observe these instructions could lead to minor or moderate injury.

 Always choose a mounting location that is sufficiently strong to withstand the loads you

intend to winch

The 4700 can be mounted to a fixed location by untilizing the mounting hole pattern for the winch

unit. First, choose a mounting location that is sufficiently strong enough to withstand the loads you

intend to winch.

Next, drill four holes to the dimesions specified in the drawing below.

Mounting Plate Hole Pattern

3/8" [9.52 mm] DIA (4 plcs)

4.5"

[114mm]

4.12"

[105mm]

PAGE 8 63998 Rev. C1

Winch Installation to a fixed location- continued

To secure the winch, always use:

▫ A flat, secure mounting location at least 3/16 in. (4.8 mm) thick steel.

▫ 3/8 in. lockwasher x 4.

▫ 3/8-16 x 1in. long, hex head capscrew, Grade 5 or better x 4.

▫ Torque mounting bolts to 30-35 ft-lbs (41-47 Nm).

Bolt length may need to be longer that specified above depending upon the thickness of the material the

winch is mounted to.

Wiring Instructions

 Install battery cables with red lead connected to the positive terminal of battery, and black lead to

the negative terminal of battery.

 Verify that all wiring connections are clean and tight.

Warning

Shock & Fire Hazard

Failure to observe these instructions could lead to severe injury or death.

 Never route electrical cables across sharp edges

 Never route electrical cables through or near moving parts.

 Always read and follow all wiring instructions included in operators guide.

 Always insulate and protect all exposed wiring and electrical terminals

 Before using the winch, verify the following:

 Wiring to all components is correct.

 There are no exposed wiring or terminals, cover any existing exposures with insulator plate,

terminal boots, heat shrink tubing or electrician’s tape.

PAGE 9 63998 Rev. C1

Operating Instructions

USING THE REMOTE CONTROL

The remote pendant control is hard waired to the winch and can be operated in the remote position aaway

from the winch unit or with the pendant docked in the carrier plate.

Press the black power-out button to spool wirerope off of the drum, or press the white power-in button to

spool wire rope onto the drum.

POWER-OUT POWER-IN

PAGE 10 63998 Rev. C1

Operating Instructions - continued

CLUTCH OPERATION

Warning

Winch Function Hazard

Failure to observe these instructions could lead to injury or property damage

 Never engage or disengage the clutch if the winch is underload or wire rope is under tension.

When the clutch is engaged the gear train is coupled to the wire rope drum and power may be transferred

from the winch motor. When the clutch is in freespool the gear train and wire rope drum are uncoupled

allowing the drum to rotate freely. The clutch lever, located on top of the motor, controls the clutch position.

To prevent damage, always fully engage or fully disengage the clutch lever.

Engaged Disengage - Freespool

PAGE 11 63998 Rev. C1

Operating Instructions - continued

SPOOLING OUT

Freespooling is generally the quickest and easiest way to spool out wire rope. Before freespooling wire rope

out from the winch, power out enough rope to remove any tension the wire rope may be under before

disengaging the clutch. Now freespool by manually spooling out enough wire rope for the winching

operation.

CAUTION

Personal Injury Hazard

Failure to observe these instructions could lead to minor or moderate injury.

 Always wear leather gloves when handling wire rope

 Never winch with less than 5 wraps of wire rope around the drum.

STRETCHING THE WIRE ROPE

The life of a wire rope is directly related to the care and use it receives. During its first use, a new wire rope

must be spooled onto its drum under a load of at least 500 lb. (227kg). Spool out the entire wire rope length

leaving 5 wraps on the drum, then power in the wire rope under a load of 500 lb. (227kg) or more. This will

stretch new wire rope and create a good wire wrap around the drum. Failure to do so may result in the

outer wire wraps drawing into the inner wraps, binding, and damaging the wire rope.

Warning

Moving Parts Entanglement Hazard

Failure to observe these instructions could lead to severe injury or death.

 ALWAYS keep hands clear of the wire rope, hook loop, hook and fairlead opening

during installation, operation and when spooling in or out.

 ALWAYS use supplied hook strap whenever spooling the wire rope in or out, during

installation, or operation to avoid injury to hands or fingers.

PAGE 12 63998 Rev. C1

Operating Instructions - continued

SPOOLING IN UNDER LOAD

 The wire rope must always spool onto the bottom of the drum as indicated by decal on the winch.

 Power in the wire rope evenly and tightly on the drum. This prevents the outer wire wraps from

drawing into the inner wraps, binding and damaging the wire rope.

 Avoid shock loads when spooling, by using the control switch intermittently to take up wire rope

slack. Shock loads can momentarily far exceed the winch and wire rope ratings.

SPOOLING IN UNDER NO LOAD

 Assisted: Have your assistant hold the hook with the hook strap putting as much constant tension

on the wire rope as possible. While keeping tension, the assistant should walk toward the winch

while you operate the control switch spooling in the wire rope. Release the switch when the hook is

a minimum of 4 ft (1.2m) from the fairlead opening. Spool in the remainder for storage.

 Unassisted: Arrange the wire rope to be spooled so it will not kink or tangle when spooled. Be sure

any wire rope on the drum is tightly and evenly layered. Spool enough wire rope to complete the

next full layer on the drum. Tighten and straighten the layer. Repeat process until the hook is a

minimum of 4ft (1.2m) from the fairlead. Spool in the remainder for storage.

SPOOLING REMAINDER FOR STORAGE

Keep hands clear of the wire rope, hook and fairlead opening. Always use the hook strap to hold hook when

spooling under no load. Carefully power in the remaining wire rope, jogging the control switch to take up the

last of the slack. Secure the hook to a suiteable anchor point near the winch. Be careful not to overtighten

or damage may occur to the wire rope or anchor point.

RIGGING

 Always spool out as much wire rope as possible when preparing rigging. Pick an anchor as far away

as is practical; this provides the winch with its greatest pulling power.

 Rigging a double line with a snatch block will reduce the load on the winch to half without significant

loss of spooling speed.

 Natural anchors such as trees, stumps and rocks are the handiest when available. Attach the choker

chain, wire choker rope or tree trunk protector on the anchor as low as possible to avoid pulling the

anchor down. If several possible anchors are available but they are not strong enough individually, it

may be practical to attach a wire or chain choker around several anchors to form a strong collective

anchor point.

PAGE 13 63998 Rev. C1

Operating Instructions - continued

OVERLOADING/OVERHEATING

This winch is rated for intermittent duty. It should not be operated with the motor slowed down to a low

RPM. When the motor approaches stall speed, a very rapid heat build-up occurs which may cause motor

damage. Double line rigging will reduce the amperage draw from the motor allowing longer continual use

(see rigging section).

Maintenance & Warranty

MAINTENANCE

 No lubrication is required for the life of the winch.

 Inspect the wire rope before and after each winching operation. Replace when damaged.

WARRANTY

see separate sheet packed with winch

-or-

If warranty sheet is lost or misplaced contact:

Warn Industries, Inc.

Customer Service Dept.

12900 SE Capps Rd

Clackamas, OR 97015-8903.

United States:

Phone: 503.722.1200 or (800) 543-9276 (US only)

Fax: 503.722-3000

International:

Phone: 503.722.3008

Fax: 503.722.3005

PAGE 14 63998 Rev. C1

GUÍA DEL CABRESTANTE PARA EL USUARIO

Cabrestante de uso general WARN Works® 4700

Nº DE REFERENCIA: 604700, 64009

Su seguridad y la seguridad de los demás es muy importante. Para ayudarle a tomar decisiones informadas sobre seguridad, se

proporcionan instrucciones de instalación y operación, y otra información en etiquetas Esta información le alerta sobre posibles peligros

que puedan afectarle a usted y a otros. No es posible advertirle sobre todos los posibles peligros que puedan estar relacionados con el

uso de este producto, por lo que deberá utilizarlo usando el sentido común.

LA INSTALACIÓN Y OPERACIÓN INCORRECTAS DEL CABRESTANTE PUEDEN RESULTAR EN LESIONES GRAVES O DAÑOS

AL EQUIPO. LEA TODAS LAS PRECAUCIONES DE SEGURIDAD E INSTRUCCIONES DE OPERACIÓN ANTES DE INSTALAR Y

PONER EN FUNCIONAMIENTO ESTE PRODUCTO.

Esta guía identifica posibles peligros y brinda importantes mensajes de seguridad que le ayudarán a usted y a otros a evitar daños

personales o la muerte. Las palabras ADVERTENCIA y PRECAUCIÓN indican el grado de peligro. He aquí su significado:

ADVERTENCIA indica un peligro que

puede

ocasionar daños personales de gravedad o la muerte si no se siguen las

recomendaciones.

PRECAUCIÓN indica un peligro que

puede

ocasionar daños personales leves o moderados si no se siguen las

recomendaciones.

Esta guía emplea la palabra

AVISO

para llamar la atención sobre importante información de carácter mecánico, y la palabra Nota: para

poner énfasis sobre información general digna de especial atención.

PAGE 15 63998 Rev. C1

Descripción del producto: Cabrestante de uso general WARN Works® 4700

El cabrestante de uso general Works® 4700 de WARN es una poderosa herramienta de arrastre. Accionado

por una fuente de energía de 12 voltios de CC, este compacto cabrestante tiene una capacidad de tiro de

2130 kilos (4700 libras).

Introducción

Gracias por su adquisición del modelo Works® de WARN para sus necesidades generales de arrastre e izado.

Todos los productos Works® de WARN se han diseñado y manufacturado para una operación sin problemas

durante muchos años. Para referencia futura, guarde la siguiente información en un lugar seguro:

Modelo/Nº de referencia: Fecha de compra:

Antes de comenzar

 Lea las instrucciones en su totalidad para familiarizarse con el proceso de instalación.

PAGE 16 63998 Rev. C1

 Revise todos los avisos, precauciones y advertencias para asegurarse de que el conjunto se instala

correcta y seguramente.

Precauciones de seguridad

A continuación se indican algunas precauciones generales de seguridad que toda persona que vaya a usar el

cabrestante debe conocer. La norma más importante, por encima de todas las demás: USE EL SENTIDO

COMÚN.

Unos pocos minutos empleados en leer estas normas pueden hacer que el operario tome conciencia de

acciones peligrosas que deben evitarse y de las precauciones a tomar para su propia seguridad y la

seguridad de los demás. Las revisiones frecuentes y las inspecciones periódicas del equipo, así como un

seguimiento consciente de las reglas de seguridad pueden salvar vidas, y también ahorrar tiempo y dinero.

ADVERTENCIA

PELIGRO DE ENREDO EN LAS PIEZAS MÓVILES

De no seguirse estas instrucciones podrían producirse lesiones graves o la muerte.

Para evitar daños en las manos.

--Mantenga siempre las manos alejadas del cable, del bucle del gancho, del gancho y de la abertura de la guía durante la

instalación, la operación, y en el enrollado y desenrollado.

• Use siempre precaución extrema en el manejo del

gancho y el cable durante las operaciones de enrollado y desenrollado.

• Use siempre la correa del gancho suministrada cuando vaya a

enrollar o desenrollar el cable durante la instalación o la operación para evitar lesiones en las manos.

ADVERTENCIA

PELIGRO DE CAÍDA O APLASTAMIENTO

De no seguirse estas instrucciones podrían producirse lesiones graves o la muerte.

• No utilice nunca el cabrestante como grúa vertical, ni para suspender una carga.

• No utilice nunca el cabrestante para levantar o desplazar personas.

PAGE 17 63998 Rev. C1

Precauciones de seguridad – Continuación

PRECAUCIÓN

PELIGRO DE ENREDO EN LAS PIEZAS MÓVILES

De no seguirse estas instrucciones podrían producirse lesiones menores o de poca gravedad.

Seguridad general:

• Sea siempre consciente del funcionamiento del cabrestante: Tómese su tiempo para leer y comprender completamente la guía de

Instalación y operaciones, y la Guía básica de técnicas del cabrestante, que vienen con el mismo, para poder comprender el

funcionamiento del cabrestante.

• No haga funcionar este cabrestante si usted es menor de 16 años de edad.

• No haga funcionar nunca el cabrestante si se encuentra bajo la

influencia de drogas, alcohol o medicamentos.

• No exceda nunca la capacidad nominal del cabrestante ni del cable de tiro. Emplee un cable doble utilizando una polea pasteca para

reducir la carga del cabrestante.

Seguridad para la instalación:

• Elija siempre una ubicación de montaje que sea lo suficientemente sólida para soportar la capacidad de carga máxima del

cabrestante.

• Utilice siempre interruptores, controles remotos, accesorios y componentes de instalación que estén aprobados de fábrica.

• Utilice siempre tornillería de grado 5 o superior, pernos que nunca hayan sido soldados y no utilice nunca pernos que sean más

largos que los suministrados por la fábrica.

• Complete siempre el montaje y acoplamiento del gancho del cabrestante al bucle del gancho antes de cablear el cabrestante durante

la instalación.

• Ponga siempre la guía del cable con la etiqueta de ADVERTENCIA en su parte superior.

• Enrolle y desenrolle el cable en el tambor siempre según lo

indicado por la etiqueta de rotación del tambor del cabrestante. Es necesario para que funcione el freno automático (si viene con el

cabrestante) y para una orientación correcta de la instalación.

• Realice siempre un estiramiento previo del cable y vuelva a enrollarlo con carga antes de usarlo. Un cable bien enrollado reduce el

riesgo de “agarrotamiento”, que consiste en el cable enrollándose en una capa de cable que está enrollada flojamente, y

enganchándose o dañándose a sí mismo.

Seguridad en el enrollado y desenrollado:

Revise siempre la instalación del cabrestante y el estado del cable antes de su uso. Si el cable está deshilachado, retorcido o dañado,

deberá reemplazarse de inmediato. Cualquier pieza instalada que esté suelta o dañada deberá corregirse de inmediato.

• No enganche nunca el cable sobre sí mismo. Esto deterioraría el cable. Utilice una cadena o un cable de estrangulación, o un

protector de tronco de árbol en el anclaje.

• Antes del enrollado, no olvide nunca retirar cualquier elemento que pueda interferir con una operación del cabrestante segura.

• Tómese su tiempo siempre cuando utilice un cabrestante.

• Verifique siempre que el anclaje seleccionado soportará la carga y que la correa o la cadena no se deslizará.

• Nunca embrague ni desembrague si el cabrestante está soportando una carga, si el cable está en tensión o si el tambor del cable

está en movimiento.

• Siempre desenrolle tanto cable como sea posible al prepararse para el maniobrado. Emplee un cable doble o elija un punto de

anclaje distante.

• No utilice nunca el cabrestante con menos de 5 vueltas de cable enrollado en el tambor; de no hacerse así el cable podría soltarse

del tambor.

• Manténgase siempre alejado del cable y de la carga durante el accionamiento del cabrestante.

• No toque nunca el cable ni el gancho mientras éstos estén en tensión o con carga.

• No toque nunca el cable ni el gancho si hay alguien cerca del interruptor de control, o si el cabrestante está en funcionamiento.

• No toque nunca el cable ni el gancho si el control remoto está enchufado al cabrestante.

• Manténgase siempre alejado del cable y de la carga, y no deje que otros se acerquen mientras el cabrestante esté en

funcionamiento.

• Haga que el operario y otras personas presentes sean conscientes de la estabilidad durante la operación del cabrestante en el

manejo del vehículo o la carga.

• Mantenga siempre el cable del control remoto alejado del tambor, del cable y del maniobrado. Inspeccione la posible existencia de

grietas, pellizcos, cables deshilachados o conexiones sueltas. Reemplácelo si está dañado.

PAGE 18 63998 Rev. C1

Precauciones de seguridad - Continuación

PRECAUCIÓN

PELIGRO DE CORTES Y QUEMADURAS

De no seguirse estas instrucciones podrían producirse lesiones menores o de poca gravedad.

Para evitar daños en las manos:

• Lleve puestos siempre guantes gruesos de cuero para manejar el cable.

• Nunca deje que el cable se deslice por sus manos.

• Tenga siempre en cuenta que las superficies del motor, del tambor o del cable del cabrestante pueden estar

calientes durante o después del uso del mismo.

PRECAUCIÓN

Peligro de enredo en las piezas móviles

De no seguirse estas instrucciones podrían producirse lesiones menores o de poca gravedad.

• No aplique nunca la carga a la punta del gancho o al seguro del mismo. Aplique la carga únicamente en el centro

del gancho.

• No utilice nunca un gancho cuya abertura haya aumentado, o cuya punta esté doblada o retorcida

AVISO

EVITE DAÑOS AL EQUIPO Y AL CABRESTANTE

Evite siempre los tirones laterales continuos ya que pueden apilar el cable en un extremo del tambor. Esto puede dañar

el cable o el cabrestante.

• Compruebe siempre que se ha embragado o desembragado completamente.

• No utilice nunca el cabrestante para remolcar otros vehículos. Las cargas repentinas pueden exceder

momentáneamente la capacidad del cable y el cabrestante.

• Sea precavido siempre para no dañar la estructura cuando vaya a anclar su vehículo en una operación con el

cabrestante.

• No desplace nunca el cable en pequeñas sacudidas cuando esté con carga. Las cargas repentinas pueden exceder

momentáneamente la capacidad del cable y el cabrestante.

• Nunca utilice el cabrestante para amarrar una carga durante el transporte.

• No sumerja nunca el cabrestante en agua.

• Guarde siempre el cabrestante en un área protegida, limpia y seca.

Número de referencia y terminales del cable para el modelo Works 4700

PAGE 19 63998 Rev. C1

NÚMEROS DE REFERENCIA

604700 Cabrestante de uso general 4700 12 V CC

64008 Cabrestan

t

e de uso

g

eneral 4700 12 V CC - Internacional

Lista de piezas

El cabrestante de uso general Works® 4700 de WARN consta de los siguientes componentes

principales.

1. Unidad de cabrestante Works 4700 2 Remoto con guía de 3,7 m (12 pies)

3 Guía: Escoben 4. 2 cables de 1,8 m (6 pies) y calibre 6

5. Gancho de retención, con correa 6. Accesorios de montaje

PAGE 20 63998 Rev. C1

1

2

3

4

5

6

La page charge ...

WARN Works 4700 Manuel utilisateur

WARN Works 4700 Manuel utilisateur

dans d''autres langues

Autres documents