GSL SOLUTIONS USB IntelliPad Prescription Storage System Manuel utilisateur

Marque
GSL SOLUTIONS
Modèle
USB IntelliPad Prescription Storage System
Taper
Manuel utilisateur
USB IntelliPad
©2020 GSL Solutions Inc. – Not to be disclosed to third parties without express written consent. Page 1 of 3
LED Indicators
Light #4 Color
Behavior
Multiple tags on pad
Red
On solid
Basket placed on the pad
Green
On solid
Basket requiring verification or reverification on the pad
Red
Blinking
ID Badge on pad
Blue
On solid
Basket in error
Red
On solid
Unknown RFID tag on the pad
Green
On solid
RFID tags removed from pad
Off
None
Light 3: Diagnostic
1 tag being read: Green
2 or more tags being read: Yellow
Light 0: Power
Power on: Green
Power off: Off
Light 2: External USB
Always solid Green
Light 4: Reflects
WCC behavior
USB IntelliPad
©2020 GSL Solutions Inc. – Not to be disclosed to third parties without express written consent. Page 2 of 3
Troubleshooting Communication to Will Call Client (WCC)
1. Check that there are not multiple RFID tags (SmartBaskets or Badges) near the IntelliPad,
including underneath the counter. Also check that there is no metal underneath.
2. Verify IntelliPad LED status
a. If Light #1 is
i. On Solid = Normal Operation
ii. Blinking Green = Attached to Windows but not attached to WCC
1. Ask if WCC is currently open
2. If already open, close and re-open WCC, wait 30-60 seconds
iii. Blinking Yellow = Powering up, not attached to Windows
1. If new workstation and OS older than Windows 10, call Local IT to install WINUSB drivers
2. Unplug USB cable at IntelliPad and plug back in
3. Lights should cycle
iv. Still blinking yellow
1. Move USB cable to another port on back of workstation
v. Still blinking yellow
1. Swap just the IntelliPad with a known working IntelliPad from another workstation
2. Wait 30-60 seconds
3. If problem stays at original workstation, it is either a cable issue or workstation issue
a. Swap cables to verify if the issue stays with the USB Cable or the workstation
i. If it stays will the cable, call GSL Support for replacement cable
ii. If it stays with the workstation, call Local IT to uninstall and re-install WINUSB
drivers
4. If problem follows the IntelliPad
a. Unplug USB cable and plug back in, wait 30-60 seconds.
b. If it is still not working, call GSL Support for replacement IntelliPad
b. If no lights:
i. Check connections at both ends of USB cable
1. Move USB cable to another port on back of workstation
ii. Still no lights
1. Swap just the IntelliPad with a known working IntelliPad from another workstation
2. Wait 30-60 seconds
3. If the original IntelliPad starts working but the one moved to the original workstation does
not
a. Call GSL Support for a replacement USB cable
4. If the original IntelliPad does not work on moved to workstation
a. Call GSL Support for a replacement IntelliPad
GSL Support (866) 477-2682
USB IntelliPad
©2020 GSL Solutions Inc. – Not to be disclosed to third parties without express written consent. Page 3 of 3
English
Per FCC 15.19(a)(3) and (a)(4) This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Per FCC 15.21 Any change or modification to this device not expressly approved by
GSL Solutions, Inc. voids your authority to operate this device.
This device complies with Industry Canada license-exempt RSS standard(s). Operation
is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
French
Selon FCC 15.19 (a ) ( 3) et (a) (4) Cet appareil est conforme à la partie 15 des règles
de la FCC. Son fonctionnement est soumis aux deux conditions suivantes: (1) Cet
appareil ne doit pas causer d'interférences nuisibles, et (2) cet appareil doit accepter
toute interférence reçue, y compris les interférences pouvant entraîner un
fonctionnement indésirable.
Conformément à la FCC 15.21 Tout changement ou modification de cet appareil non
expressément approuvé par GSL Solutions, Inc. annule votre droit d'utiliser cet appareil.
Cet appareil est conforme aux normes RSS exemptes de licence d'Industrie
Canada. Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil
ne doit pas provoquer d'interférences, et (2) cet appareil doit accepter toute
interférence, y compris les interférences susceptibles d'entraîner un fonctionnement
indésirable de l'appareil.
  • Page 1 1
  • Page 2 2
  • Page 3 3

GSL SOLUTIONS USB IntelliPad Prescription Storage System Manuel utilisateur

Marque
GSL SOLUTIONS
Modèle
USB IntelliPad Prescription Storage System
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Autres documents