Electrolux EGT6242NOK Manuel utilisateur

Catégorie
Plaques de cuisson
Taper
Manuel utilisateur
EGT6242
................................................ .............................................
EN HOB USER MANUAL 2
FR TABLE DE CUISSON NOTICE D'UTILISATION 17
CONTENTS
1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. PRODUCT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4. DAILY USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5. HELPFUL HINTS AND TIPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6. CARE AND CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
7. TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
8.
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
9. TECHNICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
WE’RE THINKING OF YOU
Thank you for purchasing an Electrolux appliance. You’ve chosen a product that brings with it
decades of professional experience and innovation. Ingenious and stylish, it has been designed
with you in mind. So whenever you use it, you can be safe in the knowledge that you’ll get great
results every time.
Welcome to Electrolux.
Visit our website for:
Get usage advice, brochures, trouble shooter, service information:
www.electrolux.com
Register your product for better service:
www.electrolux.com/productregistration
Buy Accessories, Consumables and Original spare parts for your appliance:
www.electrolux.com/shop
CUSTOMER CARE AND SERVICE
We recommend the use of original spare parts.
When contacting Service, ensure that you have the following data available.
The information can be found on the rating plate. Model, PNC, Serial Number.
Warning / Caution-Safety information
General information and tips
Environmental information
Subject to change without notice.
2
www.electrolux.com
1. SAFETY INFORMATION
Before the installation and use of the appliance, carefully
read the supplied instructions. The manufacturer is not
responsible if an incorrect installation and use causes in-
juries and damages. Always keep the instructions with
the appliance for future reference.
1.1 Children and vulnerable people safety
WARNING!
Risk of suffocation, injury or permanent disability.
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge if they are supervised by an adult or a per-
son who is responsible for their safety.
Do not let children play with the appliance.
Keep all packaging away from children.
Keep children and pets away from the appliance when
it operates or when it cools down. Accessible parts are
hot.
If the appliance has a child safety device, we recom-
mend that you activate it.
Cleaning and user maintenance shall not be made by
children without supervision.
1.2 General Safety
The appliance and its accessible parts become hot
during use. Do not touch the heating elements.
Do not operate the appliance by means of an external
timer or separate remote-control system.
Unattended cooking on a hob with fat or oil can be
dangerous and may result in fire.
ENGLISH 3
Never try to extinguish a fire with water, but switch off
the appliance and then cover flame e.g. with a lid or a
fire blanket.
Do not store items on the cooking surfaces.
Do not use a steam cleaner to clean the appliance.
Metallic objects such as knives, forks, spoons and lids
should not be placed on the hob surface since they
can get hot.
If the glass ceramic surface is cracked, switch off the
appliance to avoid the possibility of electric shock.
2.
SAFETY INSTRUCTIONS
This appliance is suitable for the following
markets: MA
GB
2.1 Installation
WARNING!
Only a qualified person must in-
stall this appliance.
Remove all the packaging.
Do not install or use a damaged appli-
ance.
Obey the installation instruction sup-
plied with the appliance.
Keep the minimum distance from the
other appliances and units.
Always be careful when you move the
appliance because it is heavy. Always
wear safety gloves.
Seal the cut surfaces with a sealant to
prevent moisture to cause swelling.
Protect the bottom of the appliance
from steam and moisture.
Do not install the appliance adjacent to
a door or under a window. This pre-
vents hot cookware to fall from the ap-
pliance when the door or the window is
opened.
If the appliance is installed above draw-
ers make sure that the space, between
the bottom of the appliance and the up-
per drawer, is sufficient for air circula-
tion.
The bottom of the appliance can get
hot. We recommend to install a non-
combustile separation panel under the
appliance to prevent access to the bot-
tom.
Electrical connection
WARNING!
Risk of fire and electrical shock.
All electrical connections must be made
by a qualified electrician.
The appliance must be earthed.
Before carrying out any operation make
sure that the appliance is disconnected
from the power supply.
Use the correct electricity mains cable.
Do not let the electricity mains cable
tangle.
Make sure the mains cable or plug (if
applicable) does not touch the hot ap-
pliance or hot cookware, when you
connect the appliance to the near sock-
ets
Make sure the appliance is installed
correctly. Loose and incorrect electricity
mains cable or plug (if applicable) can
make the terminal become too hot.
Make sure that a shock protection is in-
stalled.
Use the strain relief clamp on cable.
4
www.electrolux.com
Make sure not to cause damage to the
mains plug (if applicable) or to the
mains cable. Contact the Service or an
electrician to change a damaged mains
cable.
The electrical installation must have an
isolation device which lets you discon-
nect the appliance from the mains at all
poles. The isolation device must have a
contact opening width of minimum 3
mm.
Use only correct isolation devices: line
protecting cut-outs, fuses (screw type
fuses removed from the holder), earth
leakage trips and contactors.
Gas connection
All gas connections should be made by
a qualified person.
Before installation, make sure that the
local distribution conditions (nature of
the gas and gas pressure) and the ad-
justment of the appliance are compati-
ble.
Make sure that there is air circulation
around the appliance.
The information about the gas supply is
on the rating plate.
This appliance is not connected to a
device, which evacuates the products
of combustion. Make sure to connect
the appliance according to current in-
stallation regulations. Pay attention to
requirements regarding adequate venti-
lation.
2.2 Use
WARNING!
Risk of injury, burns or electric
shock.
Remove all the packaging, labelling and
protective film (if applicable) before first
use.
Use this appliance in a household envi-
ronment.
Do not change the specification of this
appliance.
Do not let the appliance stay unatten-
ded during operation.
Do not operate the appliance with wet
hands or when it has contact with wa-
ter.
Do not put cutlery or saucepan lids on
the cooking zones. They become hot.
Set the cooking zone to “off” after use.
Do not use the appliance as a work
surface or as a storage surface.
If the surface of the appliance is
cracked, disconnect immediately the
appliance from the power supply. This
to prevent an electrical shock.
When you place food into hot oil, it may
splash.
WARNING!
Risk of fire or explosion.
Fats and oil when heated can release
flammable vapours. Keep flames or
heated objects away from fats and oils
when you cook with them.
The vapours that very hot oil releases
can cause spontaneous combustion.
Used oil, that can contain food rem-
nants, can cause fire at a lower temper-
ature than oil used for the first time.
Do not put flammable products or items
that are wet with flammable products
in, near or on the appliance.
WARNING!
Risk of damage to the appliance.
Do not keep hot cookware on the con-
trol panel.
Do not let cookware to boil dry.
Be careful not to let objects or cook-
ware fall on the appliance. The surface
can be damaged.
Do not activate the cooking zones with
empty cookware or without cookware.
Do not put aluminium foil on the appli-
ance.
Cookware made of cast iron, aluminium
or with a damaged bottom can cause
scratches on the glass or glass ceram-
ic. Always lift these objects up when
you have to move them on the cooking
surface.
This appliance is for cooking purposes
only. Do not use the appliance for other
purposes, as for example room heating.
The use of a gas cooking appliance re-
sults in the production of heat and
moisture. Provide good ventilation in
the room where the appliance is instal-
led.
ENGLISH 5
Make sure that the ventilation openings
are not blocked.
Prolonged intensive use of the appli-
ance may call for additional ventilation,
for example opening of a window, or
more effective ventilation, for example
increasing the level of mechanical venti-
lation where present.
Use only stable cookware with the cor-
rect shape and diameter larger than the
dimensions of the burners. There is a
risk of overheating and rupture of the
glass plate (if applicable).
Make sure the flame does not go out
when you quickly turn the knob from
the maximum to the minimum position.
Make sure pots are centrally positioned
on the rings and do not stick out over
edges of the cooking surface.
Use only the accessories supplied with
the appliance.
Do not install a flame diffuser on the
burner.
2.3 Care and Cleaning
WARNING!
Risk of damage to the appliance.
Clean regularly the appliance to prevent
the deterioration of the surface material.
Do not use water spray and steam to
clean the appliance.
Do not clean the burners in the dish-
washer.
Clean the appliance with a moist soft
cloth. Only use neutral detergents. Do
not use abrasive products, abrasive
cleaning pads, solvents or metal ob-
jects.
2.4 Disposal
WARNING!
Risk of injury or suffocation.
Contact your municipal authority for in-
formation on how to discard the appli-
ance correctly.
Disconnect the appliance from the
mains supply.
Cut off the mains cable and discard it.
Flat the external gas pipes.
3. PRODUCT DESCRIPTION
3.1 Cooking surface layout
2
5
1 3
4
1
Cooktop
2
Rapid burner
3
Auxiliary burner
4
Semi-rapid burner
5
Control knobs
3.2 Control knobs
Symbol Description
no gas supply /
off position
Symbol Description
ignition position /
maximum gas
supply
6
www.electrolux.com
Symbol Description
minimum gas
supply
4. DAILY USE
WARNING!
Refer to the Safety chapters.
4.1 Ignition of the burner
WARNING!
Be very careful when you use
open fire in kitchen environment.
Manufacturer decline any respon-
sibility in case of misuse of the
flame
Always light the burner before you
put cookware.
Lightning the burner:
1.
Push the control knob down and turn
it counterclockwise to the maximum
position (
).
2.
Keep the control knob pushed for
equal or less than 10 seconds to let
the thermocouple warm up. If not, the
gas supply will be interrupted.
3.
Adjust the flame after it is regular.
If the burner does not light after
some tries, check if the crown and
its cap are in correct positions.
A
B
C
D
A)
Burner cap
B)
Burner crown
C)
Ignition candle
D)
Thermocouple
WARNING!
Do not keep the control knob
pushed for more than 15 sec-
onds.
If the burner does not light after
15 seconds, release the control
knob, turn it into off position and
try to light the burner again after
minimum 1 minute.
In the absence of electricity you
can ignite the burner without elec-
trical device; in this case approach
the burner with a flame, push the
relevant knob down and turn it
counter-clockwise to maximum
gas release position.
If the burner accidentally goes out,
turn the control knob to the off
position and try to light the burner
again after minimum 1 minute.
The spark generator can start au-
tomatically when you switch on
the mains, after installation or a
power cut. It is normal.
4.2 Turning the burner off
To put the flame out, turn the knob to the
symbol
.
WARNING!
Always turn the flame down or
switch it off before you remove the
pans from the burner.
ENGLISH 7
5. HELPFUL HINTS AND TIPS
WARNING!
Refer to the Safety chapters.
5.1 Energy savings
If possible, always put the lids on the
pans.
When the liquid starts to boil, turn down
the flame to barely simmer the liquid.
WARNING!
Use cookware with diameters ap-
plicable to the size of burners.
Burner Diameters of cook-
ware
Rapid 180 - 260 mm
Front Semi-
rapid
120 - 220 mm
Rear Semi-
rapid
120 - 220 mm
Auxiliary 80 - 180 mm
WARNING!
Do not use cast iron pans, pot-
stones, grill or toaster plates on
gas burners.
WARNING!
Make sure that the bottoms of
pots do not stand above the con-
trol knobs. If the control knobs are
under the bottoms of pots, the
flame heats them up.
Do not put the same pan on two
burners.
WARNING!
Make sure that pot handles is not
above the front edge of the cook-
top. Make sure that pots are cen-
trally put on the rings in order to
get maximum stability and to get
lower gas consumption.
Do not put unstable or damaged pots on
the rings to prevent from spill and injury.
WARNING!
Do not use a flame diffuser.
WARNING!
Liquids spilt during cooking can
cause the glass to break
6. CARE AND CLEANING
WARNING!
Refer to the Safety chapters.
WARNING!
Deactivate the appliance and let it
cool down before you clean it.
Disconnect the appliance from the
electrical supply before you do
cleaning or maintenance work.
Scratches or dark stains on the
surface have no effect on how the
appliance operates.
You can remove the pan supports to
easily clean the hob.
To clean the enamelled parts, cap and
crown, wash them with warm soapy
water and dry them carefully before you
put them back.
8
www.electrolux.com
Wash stainless steel parts with water,
and then dry them with a soft cloth.
The pan supports are not dishwasher
proof. They must be washed by hand.
When you wash the pan supports by
hand, take care when you dry them as
the enamelling process occasionally
leaves rough edges. If necessary, re-
move stubborn stains using a paste
cleaner.
Make sure you position the pan sup-
ports correctly after cleaning.
To make the burners work correctly,
make sure that the arms of the pan
supports are in the centre of the burner.
Be very careful when you replace
the pan supports to prevent the hob
top from damage.
After cleaning, dry the appliance with a
soft cloth.
Removing the dirt:
1.
Remove immediately: melting
plastic, plastic foil, and food con-
taining sugar.
Stop the appliance and let it
cool down before you clean: lime-
scale rings, water rings, fat stains,
shiny metallic discolorations. Use a
special cleaner applicable for sur-
face of hob.
2.
Clean the appliance with a damp
cloth and some detergent.
3.
At the end rub the appliance dry
with a clean cloth.
WARNING!
Do not use knives, scrapers or
similar instruments to clean the
surface of the glass or between
the rims of the burners and the
frame (if applicable).
WARNING!
Do not slide cookware over the
glass because it could scratch the
surface. Also, do not let hard or
sharp objects fall onto the glass or
hit the edge of the hob.
6.1 Cleaning of the spark plug
This feature is obtained through a ceramic
ignition candle with a metal electrode.
Keep these components well clean to
prevent difficult lighting and check that the
burner crown holes are not obstructed.
6.2 Periodic maintenance
Periodically speak your local Service
Force Centre to check the conditions of
the gas supply pipe and the pressure ad-
juster, if fitted.
7. TROUBLESHOOTING
Problem Possible cause Remedy
There is no spark when
lighting the gas
There is no electrical
supply
Make sure that the unit
is connected and the
electrical supply is
switched on.
Control the fuse. If the
fuse is released more
than one time, refer to
a qualified electrician.
Burner cap and crown
are placed uneven
Make sure that the
burner cap and crown
are in correct positions.
ENGLISH 9
Problem Possible cause Remedy
The flame is blow out im-
mediately after ignition
Thermocouple is not
heated sufficient
After lightning the
flame, keep the knob
pushed for equal or
less than 10 seconds.
The gas ring burns un-
evenly
Burner crown is
blocked with food resi-
dues
Make sure that the in-
jector is not blocked
and the burner crown
is clear of food parti-
cles.
If there is a fault, first try to find a solution
to the problem yourself. If you cannot find
a solution to the problem yourself, speak
your dealer or the local Service Force
Centre.
If you operated the appliance in-
correctly, or the installation was
not carried out by a registered en-
gineer, the visit from the customer
service technician or dealer may
not take place free of charge,
even during the warranty period.
These data are necessary to help you
quickly and correctly. These data are
available on the supplied rating plate.
Model description .................
Product number (PNC) .................
Serial Number (S.N.) .................
Use the original spare parts only. They are
available at Service Force Centre and ap-
proved spare parts shops.
7.1 Labels supplied with the
accessories bag
Stick the adhesive labels as indicated be-
low:
MOD.
PROD.NO.
SER.NO
DATA
MOD.
PROD.NO.
SER.NO
DATA
MODELMODEL
MOD.
PROD.NO.
SER.NO.
03 IT
MADE IN ITALY
TYPE
230V-50Hz
IP20
0049
A B C
A)
Stick it on Guarantee Card and send
this part (if applicable)
B)
Stick it on Guarantee Card and keep
this part (if applicable)
C)
Stick it on instruction booklet
10
www.electrolux.com
8. INSTALLATION
WARNING!
Refer to the Safety chapters.
WARNING!
The following instructions about
installation, connection and main-
tenance must be carried out by
qualified personnel in compliance
with standards and local regula-
tions in force.
8.1 Important safety
requirements
This hob must be installed in accordance
with the Gas Safety (Installation and Use)
Regulations (Current Edition) and the IEE
Wiring Regulations (Current Edition).
For appliances installed in the Republic of
Ireland please refer to NSAI- Domestic
Gas Installation I.S. 813 Current Editions
and the ETCI Rules for Electrical Installa-
tions.
Provision for ventilation
Detailed recommendations are contained
in the following British Standards Codes
Of Practice: B.S. 6172/ B.S. 5440, Par. 2
and B.S. 6891 Current Editions.
The hob should not be installed in a bed
sitting room with a volume of less than 20
m³. If it is installed in a room of volume
less than 5 m³ an air vent of effective area
of 100 cm² is required. If it is installed in a
room of volume between 5 m³ and 10 m³
an air vent of effective area of 50 cm² is
required, while if the volume exceeds 11
m³ no air vent is required.
However, if the room has a door which
opens directly to the outside no air vent is
required even if the volume is between 5
m³ and 11 m³.
If there are other fuel burning appliances
in the same room, B.S. 5440 Part 2 Cur-
rent Edition, should be consulted to deter-
mine the requisite air vent requirements.
For appliances installed in the Republic of
Ireland please refer to the NSAI- Domestic
Gas Installation I.S. 813 Current Editions
Table Four.
Location
The hob may be located in a kitchen, a
kitchen/diner or bed sitting room (with a
volume greater than 20 m³), but not in a
bathroom or shower room.
The minimum distance combustible mate-
rial can be fitted above the hob in line with
the edges of the hob is 400 mm. If it is fit-
ted below 400 mm a space of 50 mm
must be allowed from the edges of the
hob.
For appliances installed in the Republic of
Ireland please refer to NSAI- Domestic
Gas Installation I.S 813 Current Edition
Section 7- Permitted Locations of Appli-
ance.
8.2 Gas Connection
WARNING!
Any gas installation must be car-
ried out by a GAS SAFE REGIS-
TER installer.
Make sure that, once the hob is installed,
it is easily accessible for the engineer in
the event of a breakdown.
The manufacturer will not accept liability,
should the above instructions or any of
the other safety instructions incorporated
in this instruction booklet be ignored.
On the end of the shaft, which includes
the G 1/2" threaded elbow, adjustment is
fixed so that the washer is fitted between
the components as shown in the diagram.
Screw the parts together without using
excessive force.
ABC
A)
End of shaft with nut
B)
Washer
C)
Elbow
Connection to the gas supply should be
with either rigid or semi-rigid pipe, i.e.
steel or copper.
ENGLISH 11
The connection should be suitable for
connecting to R 1/2 (1/2 BSP male
thread).
When the final connection has been
made, it is essential that a thorough leak
test is carried out on the hob and installa-
tion.
Make sure that the main connection pipe
does not exert any strain on the hob.
If you use flexible metal pipes make sure
that they agree to ISO 10380 and ISO
10807 standards. Be careful they do not
come in touch with mobile parts or they
are not squeezed. Also be careful when
the hob is put together with an oven.
It is important to install the elbow
correctly, with the shoulder on the
end of the thread, fitted to the hob
connecting pipe.
Failure to ensure the correct as-
sembly will cause leakage of gas.
Make sure that the gas supply
pressure of the appliance obeys
the recommended values.
Rigid connection:
Carry out connection by using metal rigid
pipes (copper with mechanical end).
8.3 Injectors replacement
1.
Remove the pan supports.
2.
Remove the caps and crowns of the
burner.
3.
With a socket spanner 7 remove the
injectors and replace them with the
ones which are necessary for the type
of gas you use (see table in "Techni-
cal Information" chapter).
4.
Assemble the parts, follow the same
procedure backwards.
5.
Replace the rating plate (it is near the
gas supply pipe) with the one for the
new type of gas supply. You can find
this plate in the package supplied
with the appliance.
If the supply gas pressure is changeable
or different from the necessary pressure,
you must fit an applicable pressure ad-
juster on the gas supply pipe.
8.4 Adjustment of minimum level
To adjust the minimum level of the burn-
ers:
1.
Light the burner.
2.
Turn the knob on the minimum posi-
tion.
3.
Remove the knob.
4.
With a thin screwdriver, adjust the by-
pass screw position.
A
A)
The by-pass screw
If you change from natural gas G20 20
mbar to liquid gas, fully tighten the ad-
justment screw in.
If you change from liquid gas to natural
gas G20 20 mbar, undo the by-pass
screw approximately 1/4 of a turn.
WARNING!
Make sure the flame does not go
out when you quickly turn the
knob from the maximum position
to the minimum position.
8.5 Electrical connection
Do not pull the mains cable to discon-
nect the appliance. Always pull the
mains plug.
The appliance must not be connected
with an extension cable, an adapter or
a multiple socket. There is a risk of fire.
Do not let the power cable to heat up
to a temperature of more than 90° C.
The cable should be guided by means
of clamps fixed to the side of the cabi-
net, in order to avoid any contact with
the equipment beneath the cooktop.
Make sure that there is access to the
mains plug after the installation.
Electrical Requirements
Permanent electrical installation must
agree with the latest I.E.E. Regulations
12
www.electrolux.com
and local Electricity Board regulations. For
your own safety the installation must be
done by a qualified electrician (e.g. your
local Electricity Board, or a contractor
who is on the roll of the National Inspec-
tion Council for Electrical Installation Con-
tracting [NICEIC]).
The manufacturer refuses to
be held responsible, if these
safety measures are not abi-
ded by.
Supply connections:
This hob has to be connected to 230 —
240 V ( 50 Hz) electricity supply.
The hob has a terminal block which is
marked as follows:
L — Live terminal
N — Neutral terminal
or E — Earth terminal
Before carrying out the connection, make
sure:
1.
The limiter valve and the electrical
system can take the appliance load
(see the rating plate)
2.
The supply system is equipped with
an efficient earth connection in com-
pliance with the current standards
and regulations
3.
The outlet or omnipolar switch used
for connection is easily accessible
with the appliance installed.
The appliance is supplied with a 3 core
flexible powercable with a 3 amp plug. If it
is necessary to change the fuse, use a 3
amp ASTA-approved (BS 1362) fuse.
AB
C
D
E
A)
Green and Yellow
B)
3 amp fuse
C)
Brown
D)
Cord clamp
E)
Blue
The wires in the cord are coloured as fol-
lows:
Green and yellow - Earth
Blue - Neutral
Brown - Live
Replacement of the connection cable
1.
Connect the green and yellow (earth)
wire to the terminal which is marked
with the letter 'E', or the earth symbol
, or coloured green and yellow.
2.
Connect the blue (neutral) wire to the
terminal which is marked with the let-
ter 'N' or coloured blue.
3.
Connect the brown (live) wire to the
terminal which is marked with the let-
ter 'L'. It must always be connected
to the network phase.
There must be no cut or stray strands of
wire present. The cord clamp must be
correctly attached to the outer sheath.
ENGLISH 13
To replace the connection cable
use only H05V2V2-F T90 or
equivalent type. Make sure that
the cable section is applicable to
the voltage load and the working
temperature. The yellow/green
earth wire (B) must be approxi-
mately 2 cm longer than the live
and neutral wire (A).
AB
WARNING!
A cut off plug inserted into a 13
amp socket is a serious safety
(shock) hazard. Ensure that the
cut off plug is disposed of safely.
The replacement of electric cable
must be carried out exclusively by
the service force centre or by per-
sonnel with similar competencies,
in accordance with the current
regulations.
8.6 Building In
min. 600 mm
min. 55 mm
min. 650 mm
560 mm
480 mm
min. 450 mm
30 mm
B
A
A)
supplied seal
B)
supplied brackets
CAUTION!
Install the appliance only on a
worktop with flat surface.
8.7 Possibilities for insertion
Kitchen unit with door
The panel installed below the hob must
be easy to remove and let an easy access
in case a technical assistance intervention
is necessary.
min 20 mm
(max 150 mm)
30 mm
60 mm
B
A
A)
Removable panel
B)
Space for connections
Kitchen unit with oven
The electrical connection of the hob and
the oven must be installed separately for
safety reasons and to let easy remove
oven from the unit.
14
www.electrolux.com
9. TECHNICAL INFORMATION
Hob dimensions
Width: 590 mm
Length: 520 mm
Hob recess dimensions
Width: 560 mm
Length: 480 mm
Heat input
Rapid burner: 2.9 kW
Semi-rapid burner: 1.9 kW
Auxiliary burner: 1.0 kW
TOTAL POWER: G20 (2H) 20 mbar = 7.7 kW
G30 (3+) 28-30 mbar = 545 g/h
G31 (3+) 37 mbar = 536 g/h
Electric supply: 230 V ~ 50 Hz
3 core flexible cable with non rewireable
plug fitted with a 3 amp cartridge fuse
Category: II2H3+
Gas connection: G 1/2"
Gas supply: G20 (2H) 20 mbar
Appliance class: 3
By-pass diameters
Burner Ø By-pass in
1/100 mm
Auxiliary 28
Burner Ø By-pass in
1/100 mm
Semi-rapid 32
Rapid 42
Gas burners for NATURAL GAS G20 20 mbar
BURNER NORMAL POWER kW inj. 1/100 mm
Auxiliary 1.0 70
Semi-rapid 1.9 96
Rapid 2.9 119
Gas burners for LPG G30/G31 28-30/37 mbar
BURNER
NORMAL
POWER
kW
inj.
1/100 mm
G30
28-30 mbar
G31
37 mbar
g/h g/h
Auxiliary 1.0 50 73 71
Semi-rapid 1.9 71 138 136
Rapid 2.7 86 196 193
ENGLISH 15
10. ENVIRONMENT CONCERNS
Recycle the materials with the symbol
. Put the packaging in applicable
containers to recycle it.
Help protect the environment and human
health and to recycle waste of electrical
and electronic appliances. Do not dispose
appliances marked with the symbol
with the household waste. Return the
product to your local recycling facility or
contact your municipal office.
16
www.electrolux.com
SOMMAIRE
1. CONSIGNES DE SÉCURITÉ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2. INSTRUCTIONS DE SÉCURITÉ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3. DESCRIPTION DE L'APPAREIL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4. UTILISATION QUOTIDIENNE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
5. CONSEILS UTILES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
6. ENTRETIEN ET NETTOYAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7. EN CAS D'ANOMALIE DE FONCTIONNEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
8.
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
9. CARACTERISTIQUES TECHNIQUES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
NOUS PENSONS À VOUS
Merci d'avoir choisi ce produit Electrolux. Avec ce produit, vous bénéficiez de dizaines d'années
d'expérience professionnelle et d'innovation. Ingénieux et élégant, il a été conçu sur mesure pour
vous. Grâce à cet appareil, vous savez que chaque utilisation vous apportera satisfaction.
Bienvenue chez Electrolux.
Visitez notre site Internet pour :
Obtenir des conseils d'utilisation, des brochures, de l'aide, des informations :
www.electrolux.com
Enregistrer votre produit pour obtenir un meilleur service :
www.electrolux.com/productregistration
Acheter des accessoires, consommables et pièces de rechange d'origine pour votre
appareil :
www.electrolux.com/shop
SERVICE APRÈS-VENTE
N'utilisez que des pièces de rechange d'origine.
Avant de contacter le service, assurez-vous de disposer des informations suivantes :
Vous trouverez ces informations sur la plaque signalétique. Modèle, PNC, numéro de série.
Avertissement/Attention : consignes de sécurité.
Informations générales et conseils
Informations écologiques
Sous réserve de modifications.
FRANÇAIS 17
1. CONSIGNES DE SÉCURITÉ
Avant d'installer et d'utiliser cet appareil, lisez soigneuse-
ment les instructions fournies. Le fabricant ne peut être
tenu pour responsable des dommages et blessures liés à
une mauvaise installation ou utilisation. Conservez tou-
jours cette notice avec votre appareil pour vous y référer
ultérieurement.
1.1 Sécurité des enfants et des personnes
vulnérables
AVERTISSEMENT
Risque d'asphyxie, de blessure ou d'invalidité per-
manente.
Cet appareil peut être utilisé par des enfants de plus de
8 ans, ainsi que des personnes dont les capacités phy-
siques, sensorielles et mentales sont réduites ou dont
les connaissances et l'expérience sont insuffisantes, à
condition d'être surveillés par une personne responsa-
ble de leur sécurité.
Ne laissez pas les enfants jouer avec l'appareil.
Ne laissez pas les emballages à la portée des enfants.
Tenez les enfants et les animaux éloignés de l'appareil
lorsqu'il est en cours de fonctionnement ou lorsqu'il re-
froidit. Les parties accessibles sont chaudes.
Si l'appareil est équipé d'un dispositif de sécurité en-
fants, nous vous recommandons de l'activer.
Les enfants ne doivent pas nettoyer ni entreprendre
une opération de maintenance sur l'appareil sans sur-
veillance.
1.2 Sécurité générale
L'appareil et ses parties accessibles deviennent
chauds pendant son fonctionnement. Ne touchez pas
les éléments chauffants.
18
www.electrolux.com
Ne faites pas fonctionner l'appareil avec un minuteur
externe ou un système de commande à distance.
Il peut être dangereux de laisser chauffer de la graisse
ou de l'huile sans surveillance sur une table de cuisson
car cela pourrait provoquer un incendie.
N'essayez jamais d'éteindre un feu avec de l'eau. Met-
tez à l'arrêt l'appareil puis couvrez les flammes, par
exemple avec un couvercle ou une couverture ignifuge.
N'entreposez rien sur les surfaces de cuisson.
N’utilisez pas de nettoyeur vapeur pour nettoyer l'ap-
pareil.
Ne posez pas d'objets métalliques tels que couteaux,
fourchettes, cuillères ou couvercles sur la table de cuis-
son car ils pourraient chauffer.
Si la surface vitrocéramique est fissurée, mettez à l'ar-
rêt l'appareil pour éviter tout risque d'électrocution.
2.
INSTRUCTIONS DE SÉCURITÉ
Cet appareil est adapté aux marchés
suivants : MA
GB
2.1 Installation
AVERTISSEMENT
L'appareil doit être installé unique-
ment par un professionnel qualifié.
Retirez l'intégralité de l'emballage.
N'installez pas et ne branchez pas un
appareil endommagé.
Suivez scrupuleusement les instructions
d'installation fournies avec l'appareil.
Respectez la distance minimale requise
avec les autres appareils et éléments.
Soyez toujours vigilants lorsque vous
déplacez l'appareil car il est lourd. Por-
tez toujours des gants de sécurité.
Isolez les surfaces découpées à l'aide
d'un matériau d'étanchéité pour éviter
que la moisissure ne provoque de gon-
flements.
Protégez la partie inférieure de l'appa-
reil de la vapeur et de l'humidité.
N'installez pas l'appareil près d'une
porte ou sous une fenêtre. Les réci-
pients chauds risqueraient de tomber
de l'appareil lors de l'ouverture de cel-
les-ci.
Si l'appareil est installé au-dessus de ti-
roirs, assurez-vous qu'il y a suffisam-
ment d'espace entre le fond de l'appa-
reil et le tiroir supérieur pour que l'air
puisse circuler.
Le dessous de l'appareil peut devenir
très chaud. Nous vous recommandons
d'installer un panneau de séparation
ignifuge sous l'appareil pour en bloquer
l'accès.
Branchement électrique
AVERTISSEMENT
Risque d'incendie ou d'électrocu-
tion.
FRANÇAIS 19
L'ensemble des branchements électri-
ques doit être effectué par un techni-
cien qualifié.
L'appareil doit être relié à la terre.
Avant toute intervention, assurez-vous
que l'appareil est débranché.
Utilisez le câble d'alimentation électri-
que approprié.
Ne laissez pas le câble d'alimentation
s'emmêler.
Assurez-vous que le câble d'alimenta-
tion ou la fiche (si présente) n'entrent
pas en contact avec les surfaces brû-
lantes de l'appareil ou les récipients
brûlants lorsque vous branchez l'appa-
reil à des prises électriques situées à
proximité.
Assurez-vous que l'appareil est bien in-
stallé. Un câble d'alimentation lâche et
inapproprié ou une fiche (si présente)
non serrée peuvent être à l'origine
d'une surchauffe des bornes.
Assurez-vous qu'une protection anti-
électrocution est installée.
Utilisez un collier anti-traction sur le câ-
ble.
Veillez à ne pas endommager la fiche
secteur (si présente) ni le câble d'ali-
mentation. Contactez le service après-
vente ou un électricien pour remplacer
le câble d'alimentation s'il est endom-
magé.
L'installation électrique doit être équi-
pée d'un dispositif d'isolement à cou-
pure omnipolaire. Le dispositif d'isole-
ment doit présenter une distance d'ou-
verture des contacts d'au moins 3 mm.
N'utilisez que des systèmes d'isolation
appropriés : des coupe-circuits, des fu-
sibles (les fusibles à visser doivent être
retirés du support), un disjoncteur diffé-
rentiel et des contacteurs.
Raccordement au gaz
Tout raccordement au gaz doit être ef-
fectué par une personne qualifiée.
Avant l'installation, vérifiez que les con-
ditions de distribution locales (nature et
pression du gaz) sont compatibles avec
le réglage de l'appareil.
Assurez-vous que l'air circule autour de
l'appareil.
Les informations relatives à l'alimenta-
tion en gaz se trouvent sur la plaque si-
gnalétique.
Cet appareil n'est pas raccordé à un
dispositif d'évacuation des produits de
combustion. Veillez à brancher l'appa-
reil en conformité avec les réglementa-
tions d'installation en vigueur. Veillez à
respecter les exigences en matière
d'aération.
2.2 Utilisation
AVERTISSEMENT
Risque de blessures, de brûlures
ou d'électrocution.
Avant la première utilisation, retirez les
emballages, les étiquettes et les films
de protection (si présents).
Utilisez cet appareil dans un environne-
ment domestique.
Ne modifiez pas les caractéristiques de
cet appareil.
Ne laissez jamais l'appareil sans surveil-
lance pendant son fonctionnement.
N'utilisez jamais cet appareil avec les
mains mouillées ou lorsqu'il est en con-
tact avec de l'eau.
Ne posez pas de couverts ou de cou-
vercles sur les zones de cuisson. Elles
sont chaudes.
Éteignez les zones de cuisson après
chaque utilisation.
N'utilisez jamais l'appareil comme plan
de travail ou comme plan de stockage.
Si la surface de l'appareil présente des
fêlures, débranchez immédiatement
l'appareil pour éviter tout risque d'élec-
trocution.
Lorsque vous versez un aliment dans
de l'huile chaude, elle peut éclabous-
ser.
AVERTISSEMENT
Risque d'explosion ou d'incendie.
Les graisses et l'huile chaudes peuvent
dégager des vapeurs inflammables. Te-
nez les flammes ou les objets chauds
éloignés des graisses et de l'huile lors-
que vous vous en servez pour cuisiner.
Les vapeurs dégagées par l'huile très
chaude peuvent provoquer une com-
bustion spontanée.
20
www.electrolux.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

Electrolux EGT6242NOK Manuel utilisateur

Catégorie
Plaques de cuisson
Taper
Manuel utilisateur

dans d''autres langues