Yamaha NS-515F Manuel utilisateur

Yamaha
Marque
Yamaha
Modèle
NS-515F
Catégorie
Amplificateur d'instruments de musique
Taper
Manuel utilisateur
English
E-1
Thank you for selecting this YAMAHA NS-515F speaker system.
NS-515F
Speaker System
OWNER’S MANUAL
G R
Read this before using the speaker.
●
To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
●
Install the speaker in a cool, dry, clean place – away from
windows, heat sources, sources of excessive vibration,
dust, moisture and cold. Avoid sources of humming
(transformers, motors). To prevent fire or electrical shock,
do not expose the speaker to rain or water.
● To prevent the enclosure from warping or discoloring, do
not place the speaker where it will be exposed to direct
sunlight or excessive humidity.
● Do not place the following objects on the speaker:
Glass, china, etc.
If glass etc. falls by vibrations and breaks, it may cause
personal injury.
A burning candle etc.
If the candle falls by vibrations, it may cause fire and
personal injury.
A vessel with water in it
If the vessel falls by vibrations and water spills, it may
cause damage to the speaker, and/or you may get an
electric shock.
● Do not place the speaker where foreign objects such as
water drips might fall. It might cause a fire, damage to
the speaker, and/or personal injury.
● Do not place the speaker where it is liable to be knocked
over or struck by falling objects. Stable placement will
also ensure better sound performance.
PRECAUTIONS
The speaker is constructed with the majority of the weight
located in its upper portion, and is thus susceptible to falling
over if proper care is not taken to insure its stability. If the
speaker falls over, it may damage the speaker or be the
cause of injury (or even death) to persons and/or damage to
personal property.
For safe and proper use of the speaker:
• Position the speaker in a location that is solid, level,
smooth, and low (with respect to the floor).
• Do not push or apply pressure to the side of the speaker
when moving, or lean objects against the side of the
speaker.
• Do not sit on or set objects on top of the speaker.
PRECAUTIONS WHEN POSITIONING THE SPEAKERS
Vibrations or jolts associated with earthquakes and other
phenomena or activities may cause the speaker to fall over.
For safety reasons, using commercially available products
that increase stability in the speaker is recommended
(metal fittings or chains, etc.).
Use the stands included with the speaker to increase
stability:
Be sure to use the stands regardless of where the speaker
is positioned. Attaching the stands included with the
speaker reinforces the base of the speaker not to fall over.
Please be cautioned that even though the stands are
connected, this does not guarantee that the speaker will not
fall over.
● Placing the speaker on the same shelf or rack as the
turntable can result in feedback.
● Never put a hand or a foreign object into the port located
on the rear of the speaker as this might cause personal
injury and/or damage to the speaker.
● When moving the speaker, do not hold the port as it
might cause personal injury and/or damage to the
speaker.
● Any time you note distortion, reduce the volume control
on your amplifier to a lower setting. Never allow your
amplifier to be driven into “clipping”. Otherwise the
speaker may be damaged.
●
When using an amplifier with a rated output power higher
than the nominal input power of the speaker, care should
be taken never to exceed the speaker’s maximum input.
●
Do not attempt to clean the speaker with chemical solvents
as this might damage the finish. Use a clean, dry cloth.
● Do not attempt to modify or fix the speaker. Contact
qualified YAMAHA service personnel when any service
is needed. The cabinet should never be opened for any
reasons.
● Secure placement or installation is the owner’s
responsibility.
YAMAHA shall not be liable for any accident caused
by improper placement or installation of the speaker.
NS-515F ENG(02.8.21)a 02.8.21, 8:38 PM1
E-2
ATTACHING THE STANDS
When placing the speakers, be sure to use the stands to
increase stability.
Note
The provided stands are in two types. Two stands are
for the right side and others are for the left side. Attach
each stand to the proper position on the bottom of the
speaker by following the figure below.
Use the 8 specified holes located on the base of the
speaker.
Pad x 4
Screw
(
6mm) x 4
Stand (R x 2, L x 2)
Wood screw
(
4mm) x 4
1
2
Procedure:
1
Put the 6mm screw through the large hole on the
stand, and screw it into the speaker at one of the
outside holes on the base of the speaker.
At this time, screw it untightly so that the stand can still
be moved.
2
Put the 4mm wood screw through the other hole on the
stand, and screw it into the other hole on the base of
the speaker.
3
Tighten both of the screws firmly.
4
Attach a pad to the bottom of the end portion of the
stand.
5
Attach the other stands to the other corners of the
base of the speaker in the same way and confirm that
all 4 stands have been firmly attached.
Note
Be carefull not to apply force to the side of the speaker,
otherwise the speaker may fall causing damage to the
speaker or personal injury.
View from the bottom of the speaker
(L)
(R)
(R)
(L)
Front
Back
(L) (R)
NS-515F ENG(02.8.21)a 02.8.21, 8:38 PM2
English
E-3
SPEAKERS
A
B
L
R
+
+
–
–
+
–
CONNECTIONS TO YOUR AMPLIFIER
This speaker system is capable of standard connections and bi-wired connections. Before making
connections, make sure that the amplifier is switched off.
■CONNECTIONS
• Connect the screw-type input terminals at the rear of the
speakers to the speaker output terminals of the amplifier
(or receiver) with the speaker cable.
• Connect the (+) terminals on the amplifier (or receiver)
and the speakers using one side of the cable. Connect
the (–) terminals on both components using the other
side of the cable.
• Connect one speaker to the left (marked L) terminals of
your amplifier, and another speaker to the right (marked
R) terminals, making sure not to reverse the polarity
(+, –). If one speaker is connected with reversed polarity,
the sound will be unnatural and lack bass.
How to connect:
1 Loosen the knob.
2 Remove the insulation coating at the extremity of each
speaker cable by twisting the coating off.
3 Insert the bare wire.
4 Tighten the knob and secure the cables.
Test the firmness of the connection by pulling lightly on
the cables at the terminal.
Note
Do not let the bare speaker wires touch each other as
this could damage the speaker or the amplifier, or both
of them.
<Standard connections>
NS-515F
NS-515F
Speakers output
terminals of the
amplifier
Leave the short
bars in place
when
connecting.
Short bar
Amplifier or
Receiver
Loosen
Tighten
When using a banana plug
<General model only>
1 Remove the cover by pulling it toward you.
2 Tighten the terminal knob.
3 Simply insert the banana plug into the terminal.
Banana plug
2
1
3
(L)(R)
NS-515F ENG(02.8.21)a 02.8.21, 8:38 PM3
E-4
Bi-Wired Connections
This speaker system is capable of bi-wired
connections. To connect the speaker to the output
terminals of the amplifier (or receiver), two pairs
of cables for each of mid-woofer/woofer and
tweeter used instead of standard connections.
This type of connection decreases the modulation
distortion caused by electric resistance of the
cables and driving current of the speakers.
Consequently, purer sound quality can be
expected.
To utilize bi-wired connections, remove the short
bars from the terminals first, and then connect the
mid-woofer/woofer and tweeter to the amplifier
separately using two pairs of cables.
<Bi-wired connections>
NS-515F (L)
NS-515F (R)
NS-515F (L)NS-515F (R)
Amplifier or
Receiver
Amplifier or
Receiver
Remove the short
bars before
connecting.
Mid-woofer/woofer
terminals
Tweeter
terminals
Both SPEAKERS A and B
should be selected.
++ ––
SPEAKERS
L
R
SPEAKERS
A
B
L
R
++ ––
+
–
NS-515F ENG(02.8.21)a 02.8.21, 8:38 PM4
English
E-5
The front cover is fastened to the enclosure at six points
and can be removed if desired. To remove the cover, hold
on to both sides and slowly pull straight away from the
speaker. To reattach, line up the six holes on the inner
surface of the cover with the six corresponding pegs on the
speaker and push gently.
Note
When the cover is removed, take care not to touch the
speaker units with your hands or to exert excessive
force with tools.
SPECIFICATIONS
Type ............................. 3-way bass reflex speaker system
Magnetic shielding type
Driver ......................................... 16 cm (6.5”) cone woofer
16 cm (6.5”) cone mid-woofer
3 cm (1”) dome tweeter
Impedance ................................................................... 6 Ω
Frequency Response ................................40 Hz to 50 kHz
Nominal Input Power ................................................ 100 W
Maximum Input Power.............................................. 300 W
Sensitivity ...................................................90 dB/2.83 V/m
Crossover Frequency ...................................500 Hz, 3 kHz
Dimensions (WxHxD) .......................200 x 1000 x 328 mm
(7-7/8” x 39-3/8” x 12-15/16”)
Weight ................................................. 21 kg (46 lbs. 3 oz.)
(Including the stands)
Accessories ................................... Stand x 4 (L x 2, R x 2)
Screw (6mm) x 4
Wood screw (4mm) x 4
Pad x 4
● Specifications subject to change without notice due to
product improvements.
● Care should be taken not to exceed the input power
values noted above.
REMOVING THE FRONT COVER
■ Using as 2ch stereo speakers
Better stereo images will be obtained when the speakers
are slightly angled in towards the listeners.
■ Using as main speakers in a multi channel
system
Position the speakers on both sides of the TV. The
positioning of speakers is important, because it controls the
whole sound quality of a multi channel system. Set up the
speakers on the basis of your listening position by following
the owner’s manual supplied with your amplifier.
Note
This speaker features a magnetically shielded design,
but there is still a chance that placing it too close to a
TV set might impair picture color. Should this happen,
move the speaker away from the TV set.
PLACING THE SPEAKERS
Subwoofer
Center
NS-515F
NS-515F
Rear effect
NS-515F ENG(02.8.21)a 02.8.21, 8:39 PM5
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR, 22-34, 25462 RELLINGEN, BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VASTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
V992910
Printed in Indonesia
HYOU-4 02.8.28, 11:40 AM2
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Yamaha NS-515F Manuel utilisateur

Yamaha
Marque
Yamaha
Modèle
NS-515F
Catégorie
Amplificateur d'instruments de musique
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes