Indesit PWC 91271 W (EU) Mode d'emploi

Catégorie
Machines à laver
Taper
Mode d'emploi
GB
1
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Description of the washing machine
and starting a wash cycle, 4-5
Control panel
Indicator lights
Starting a wash cycle
Wash cycles, 6
Table of wash cycles
Personalisation, 7
Setting the temperature
Setting the spin speed
Functions
Detergents and laundry, 8
Detergent dispenser drawer
Bleach cycle
Preparing the laundry
Garments requiring special care
Precautions and tips, 9
General safety
Load balancing system
Disposal
Care and maintenance, 10
Cutting off the water or electricity supply
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Troubleshooting, 11
Service, 12
PWC 91271 W
Instructions for use
WASHING MACHINE
English,1
GB
Português,25
PT
DE
Deutsch,37
Español, 49
ES
Français,13
F
2
GB
! This instruction manual should be kept in a safe place for
future reference. If the washing machine is sold, transferred
or moved, make sure that the instruction manual remains
with the machine so that the new owner is able to familiari-
se himself/herself with its operation and features.
! Read these instructions carefully: they contain vital infor-
mation relating to the safe installation and operation of the
appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its packaging.
2. Make sure that the washing machine has not been
damaged during the transportation process. If it has been
damaged, contact the retailer and do not proceed any
further with the installation process.
3. Remove the 4 protective
screws (used during tran-
sportation) and the rubber
washer with the correspon-
ding spacer, located on the
rear part of the appliance
(see figure).
4. Close off the holes using the plastic plugs provided.
5. Keep all the parts in a safe place: you will need them
again if the washing machine needs to be moved to ano-
ther location.
! Packaging materials should not be used as toys for
children.
Levelling
1. Install the washing machine on a flat sturdy floor, without
resting it up against walls, furniture cabinets or anything
else.
2. If the floor is not perfectly
level, compensate for any
unevenness by tightening
or loosening the adjusta-
ble front feet (see figure);
the angle of inclination,
measured in relation to the
worktop, must not exceed
2°.
Levelling the machine correctly will provide it with stability,
help to avoid vibrations and excessive noise and prevent it
from shifting while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow a sufficient
ventilation space underneath the washing machine.
Connecting the electricity and water
supplies
Connecting the water inlet hose
1. Connect the supply pipe
by screwing it to a cold
water tap using a ¾ gas
threaded connection (see
figure).
Before performing the con-
nection, allow the water to
run freely until it is perfectly
clear.
2. Connect the inlet hose
to the washing machine by
screwing it onto the corre-
sponding water inlet of the
appliance, which is situa-
ted on the top right-hand
side of the rear part of the
appliance (see figure).
3. Make sure that the hose is not folded over or bent.
! The water pressure at the tap must fall within the values
indicated in the Technical details table (see next page).
! If the inlet hose is not long enough, contact a specialised
shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
Installation
GB
3
Connecting the drain hose
Connect the drain hose,
without bending it, to a drai-
nage duct or a wall drain
located at a height between
65 and 100 cm from the
floor;
alternatively, rest it on
the side of a washbasin
or bathtub, fastening the
duct supplied to the tap
(see figure). The free end
of the hose should not be
underwater.
! We advise against the use of hose extensions; if it is
absolutely necessary, the extension must have the same
diameter as the original hose and must not exceed 150 cm
in length.
Electrical connections
Before plugging the appliance into the electricity socket,
make sure that:
• thesocketisearthedandcomplieswithallapplicable
laws;
• thesocketisabletowithstandthemaximumpowerload
of the appliance as indicated in the Technical data table
(see opposite);
• thepowersupplyvoltagefallswithinthevaluesindicated
in the Technical data table (see opposite);
• thesocketiscompatiblewiththeplugofthewashing
machine. If this is not the case, replace the socket or the
plug.
! The washing machine must not be installed outdoors,
even in covered areas. It is extremely dangerous to leave
the appliance exposed to rain, storms and other weather
conditions.
! When the washing machine has been installed, the elec-
tricity socket must be within easy reach.
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable must only be replaced by autho-
rised technicians.
Warning! The company shall not be held responsible in the
event that these regulations are not respected.
The first wash cycle
Once the appliance has been installed, and before you use
it for the first time, run a wash cycle with detergent and no
laundry, using the wash cycle 2.
65 - 100 cm
Technical data
Model
PWC 91271 W
Dimensions
width 59.5 cm
height 85 cm
depth 60 cm
Capacity
from 1 to 9 kg
Electrical
connections
please refer to the technical data plate
fixed to the machine
Water connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 62 litres
Spin speed
up to 1200 rotations per minute
Test Program-
mes according to
2010/1061
programme 2;
temperature 60°C and 40°C.
Test Programmes
according to
EN 60456
programme 2; temperature 60°C;
using a load of 9 kg.
This appliance conforms to the following
EC Directives:
- 2004/108/EC (Electromagnetic Compa-
tibility)
- 2006/95/EC (Low Voltage)
- 2002/96/EC
TRRUCH
4
GB
Detergent dispenser drawer: used to dispense
detergents and washing additives (see “Detergents and
laundry”).
ON/OFF button: switches the washing machine on and off.
WASH CYCLE knob: programmes the wash cycles. Du-
ring the wash cycle, the knob does not move.
FUNCTION buttons with indicator light: used to select the
available functions. The indicator light corresponding to the
selected function will remain lit.
TEMPERATURE button: sets the temperature or the cold
wash cycle (see “Personalisation”).
SPIN button: sets the spin speed or exclude the spin cycle
completely (see “Personalisation”).
DELAY TIMER button: delays the start of the wash cycle
by up to 9 hours.
Press the button repeatedly until the indicator light corre-
sponding to the desired delay time turns on.
When the button is pressed for the fourth time, the option
will be deactivated.
N.B.: once the START/PAUSE button has been pressed,
the delay time can only be modified by decreasing it until
the set programme is launched.
! This option is available on all programmes.
WASH CYCLE PROGRESS
indicator light
s: used to
monitor the progress of the wash cycle.
The illuminated indicator light shows which phase is in
progress.
DOOR LOCKED indicator light: indicates whether the
door may be opened or not (see next page).
START/PAUSE button with indicator light: starts or tem-
porarily interrupts the wash cycles.
N.B. To pause the wash cycle in progress, press this
button; the corresponding indicator light will flash orange,
while the indicator light for the current wash cycle phase
will remain lit in a fixed manner. If the DOOR LOCKED
indicator light is switched off, the door may be opened
(wait approximately 3 minutes).
To start the wash cycle from the point at which it was inter-
rupted, press this button again.
Standby mode
This washing machine, in compliance with new energy sa-
ving regulations, is fitted with an automatic standby system
which is enabled after about 30 minutes if no activity is
detected. Press the ON-OFF button briefly and wait for the
machine to start up again.
Description of the washing
machine and starting a wash cycle
Control panel
WASH CYCLE PROGRESS
indicator lights
DOOR LOCKED
indicator light
START/
PAUSE
button with
indicator light
Detergent dispenser drawer
ON/OFF
button
WASH CYCLE
knob
DELAY TIMER
button
INDICATOR
LIGHTS
TEMPERATURE
button
SPIN
button
FUNCTION
buttons with
indicator lights
GB
5
Indicator lights
The indicator lights provide important information.
This is what they can tell you:
Delayed start
If the DELAY TIMER function has been activated (see “Per-
sonalisation”), after the wash cycle has been started the
indicator light corresponding to the selected delay period
will begin to flash:
As time passes, the remaining delay will be displayed and
the corresponding indicator light will flash:
The set programme will start once the selected time delay
has expired.
Wash cycle phase indicator lights
Once the desired wash cycle has been selected and has be-
gun, the indicator lights switch on one by one to indicate which
phase of the cycle is currently in progress.
Function buttons and corresponding indicator lights
When a function is selected, the corresponding indicator
light will illuminate.
If the selected function is not compatible with the program-
med wash cycle, the corresponding indicator light will flash
and the function will not be activated.
If the selected function is not compatible with another
function which has been selected previously, the indicator
light corresponding to the first function selected will
flash and only the second function will be activated; the
indicator light corresponding to the enabled option will
remain lit.
Note: if the
function is active, all other non-compatible
functions cannot be activated.
Door locked indicator light
When the indicator light is on, the porthole door is locked
to prevent it from being opened; make sure the indicator
light is off before opening the door (wait approximately 3
minutes).
To open the door during a running wash cycle, press the
START/PAUSE button; the door may be opened once the
DOOR LOCKED indicator light turns off.
! If the “functions” and START/PAUSE indicator lights flash
fast and the “current phase” and DOOR LOCKED indicator
lights turn on, there is an anomaly (see “Troubleshooting”).
Starting a wash cycle
1. Turn the washing machine on by pressing the ON/OFF button. All the indicator lights will turn on for a few seconds, then only
the indicator lights relative to the selected programme settings will remain lit and the START/PAUSE indicator light will flash.
2. Load the laundry and close the door.
3. Set the WASH CYCLE knob to the desired programme.
4. Set the washing temperature (see “Personalisation”).
5. Set the spin speed (see “Personalisation”).
6. Measure out the detergent and washing additives (see “Detergents and laundry”).
7. Select the desired functions.
8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit in a fixed
manner in blu. To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new
cycle.
9. At the end of the wash cycle the
indicator light will switch on. The door can be opened once the DOOR LOCK indi-
cator light turns off (wait approximately 3 minutes). Take out your laundry and leave the appliance door ajar to make sure the
drum dries completely. Switch the washing machine off by pressing the ON/OFF button.
Wash
Rinse
Spin
Drain
End of wash cycle
WASH CYCLE PROGRESS
indicator lights
END
6
GB
Wash cycles
Table of wash cycles
Wash cycles
Description of the wash cycle
Max.
temp.
C)
Max.
speed
(rpm)
Detergents
Max. load
(kg)
Cycle
duration
Prewash Main wash Bleach
Fabric
softener
Daily Programs
1
Cottons with Prewash: extremely soiled whites. 90° 1200
-
9 195
2
White Cottons: heavily soiled whites. 90° 1200 -
9 180
2
White Cottons (1): heavily soiled whites and resistant colours. 60° 1200 -
9 190
2
White Cottons (1-2): lightly soiled whites and delicate colours. 40° 1200 -
9 165
3
Cottons: heavily soiled whites and resistant colours. 60° 1200 -
9 140
4
Coloured Cottons (3): lightly soiled whites and delicate colours. 40° 1200 -
9 100
5
Synthetics: heavily soiled resistant colours. 60° 800 -
4 90
6 Jeans
40° 800 -
-
4 70
7 Shirts
40° 600 -
2 70
8
Mix-Cool 30’: to refresh lightly soiled garments quickly (not suitable
for wool, silk and clothes which require washing by hand).
Cold
water
800 -
-
3 30
Special cycles
9
Wool: for wool, cashmere, etc. 40° 600 -
-
2 55
10
Silk/Curtains: for garments in silk and viscose, lingerie. 30° 0 -
-
2 70
11 Duvets
30° 1000 -
-
3 120
12 Outwear
30° 600 -
- - 2,5 60
13 Sport Shoes
30° 600 -
-
Max.
2 pairs
60
Partial cycles
Rinse - 1200 - -
9 35
Spin - 1200 - - - - 9 15
Drain - 0 - - - - 9 2
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary
according to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options
selected.
For all Test Institutes:
1) Test wash cycle in compliance with regulation 2010/1061: set wash cycle 2 with a temperature of 60°C and 40°C.
2) Long wash cycle for cottons: set wash cycle 2 with a temperature of 40°C.
3) Short wash cycle for cottons: set wash cycle 4 with a temperature of 40°C.
1) Test wash cycle in compliance with regulation EN 60456: set wash cycle 2 with a temperature of 60°C.
TRRUCH
GB
7
Setting the temperature
Press the TEMPERATURE button to set the wash temperature (see Table of wash cycles).
The temperature may be lowered, or even set to a cold wash
.
The washing machine will automatically prevent you from selecting a temperature which is higher than the maximum value
set for each wash cycle.
Setting the spin speed
Press the SPIN SPEED button to set the spin speed for the selected wash cycle.
The maximum spin speeds available for each wash cycle are as follows:
Wash cycles Maximum spin speed
Cottons 1200 rpm
Synthetics 800 rpm
Wool 600 rpm
Silk drain only
The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol
.
The washing machine will automatically prevent you from selecting a spin speed which is higher than the maximum speed
set for each wash cycle.
Functions
The various wash functions available with this washing machine will help to achieve the desired results, every time.
To activate the functions:
1. Press the button corresponding to the desired function;
2. the function is enabled when the corresponding indicator light is illuminated.
Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in conjunction with the
selected wash cycle.
ThePRIMEtechnology optimises energy, water and time consumption according to the quantity of garments actually inserted in the
machine. Moreover, pressing the
button allows for selecting the following options:
- Water: allows for reducing water consumption without having to renounce impeccable results (recommended for heavily
soiled garments).
- Energy: automatically selected by “PRIME”, this option reduces energy consumption (recommended for normally soiled
garments).
- Time: allows for reducing wash cycle duration (recommended for lightly soiled garments).
! This may only be used in conjunction with wash cycles 1, 2, 3, 4, 5 (all three levels) and 6, 7, 8 (- Energy and - Time levels).
Extra Rinse
By selecting this option, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is particularly
useful for sensitive skin.
! It cannot be used in conjunction with wash cycles 8,
, .
Easy iron
By selecting this function, the wash and spin cycles will be modified in order to reduce the formation of creases. At the end
of the cycle the washing machine will perform slow rotations of the drum, while the EASY IRON and START/PAUSE indica-
tor lights will flash (blue and orange respectively) and the
led will remain lit in a fixed manner. To end the cycle, press the
START/PAUSE button or the EASY IRON button. For wash cycles number 10-12, the machine will end the cycle while the
laundry is soaking; the EASY IRON and START/PAUSE indicator lights will flash. To drain the water so that the laundry may
be removed, press the START/PAUSE button or the EASY IRON button.
! It cannot be used in conjunction with wash cycles 8, 9, 13,
, .
Stain removal
Bleaching cycle designed to remove the toughest stains. Please remember to pour the bleach into extra compartment 4 (see
“Bleach cycle”).
! This function may not be used in conjunction with wash cycles 1, 6, 8, 9, 10, 11, 12, 13,
, .
Personalisation
8
GB
Detergents and laundry
Detergent dispenser drawer
Good washing results also depend on the correct dose of
detergent: adding too much detergent will not necessa-
rily result in a more efficient wash, and may in fact cause
build up on the inside of your appliance and contribute to
environmental pollution.
! Do not use hand washing detergents because these
create too much foam.
Open the detergent dispen-
ser drawer and pour in the
detergent or washing additive,
as follows.
Compartment 1:
Pre-wash detergent
(powder)
Before pouring in the deter-
gent, make sure that extra
compartment 4 has been
removed.
Compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in immediately
prior to the start of the wash cycle.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
Extra compartment 4: Bleach
Bleach cycle
! Traditional bleach should be used on sturdy white fa-
brics, and delicate bleach for coloured fabrics, synthetics
and for wool.
This option is particularly useful for the removal of stubborn
stains. Place extra compartment 4 (supplied) into
compartment 1. When pouring in the bleach, be careful
not to exceed the “max” level marked on the central pivot
(see figure). To run the bleach cycle on its own, pour
the bleach into extra compartment 4, set the “Rinse”
programme and activate the “Stain removal”
option. To
bleach during a wash cycle, pour in the detergent and any
fabric softener you wish to use, set the desired wash cycle
and enable the “Stain removal”
option. The use of extra
compartment 4 excludes the “Prewash”.
Preparing the laundry
•Dividethelaundryaccordingto:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
•Emptyallgarmentpocketsandcheckthebuttons.
•Donotexceedthelistedvalues,whichrefertotheweight
of the laundry when dry:
Durable fabrics: max. 9 kg
Synthetic fabrics: max. 4 kg
Delicate fabrics: max. 2 kg
Wool: max. 2 kg
Silk: max. 2 kg
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
Garments requiring special care
Jeans: turn the garments inside out before washing and
use liquid detergent. Use wash cycle 6.
Shirts: use special wash cycle 7 to wash shirts in various
fabrics and colours. It guarantees maximum care is taken
of the garments and minimises the formation of creases.
Mix-Cool 30’: this wash cycle was designed to wash
lightly soiled garments quickly: it lasts just 30 minutes and
therefore saves both energy and time. By selecting wash
cycle 8, it is possible to wash different fabrics (except for
wool and silk items) using a cold cycle, up to a maximum
load of 3 kg.
Wool: wash cycle 9 can be used to wash all woollen gar-
ments in the machine, even those carrying the “hand wash
only”
label. To achieve the best results, use a special
detergent and do not exceed the maximum load of 2 kg.
Silk: use special wash cycle 10 to wash all silk garments.
We recommend the use of special detergent which has
been designed to wash delicate clothes.
Curtains: we recommend you fold the curtains and place
them in a pillow case or mesh bag. Use wash cycle 10.
Duvets: to wash double or single duvets (the weight
of which should not exceed 3 kg), cushions or clothes
padded with goose down such as puffa jackets, use the
special wash cycle number 11 “Duvets”. We recommend
that duvets are placed in the drum with their edges folded
inwards (see figure) and that no more than ¾ of the total
volume of the drum is used. To achieve the best results,
we recommend that a liquid detergent is used and placed
inside the detergent dispenser drawer.
Outwear (wash cycle 12): is studied for washing water-re-
pellent fabrics and winter jackets (e.g. Gore-Tex, polyester,
nylon); for best results, use a liquid detergent and dosage
suitable for a half-load; pre-treat necks, cuffs and stains if
necessary; do not use softeners or detergents containing
softeners. Stuffed duvets cannot be washed with this
programme.
Sport Shoes (wash cycle 13): is for washing sports
shoes; for best results, do not wash more than 2 pairs
simultaneously.
4
2
3
1
4
2
1
3
GB
9
Precautions and tips
! This washing machine was designed and constructed in
accordance with international safety regulations. The fol-
lowing information is provided for safety reasons and must
therefore be read carefully.
General safety
• Thisappliancewasdesignedfordomesticuseonly.
• Thisapplianceisnotintendedforusebypersons(inclu-
ding children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concer-
ning use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that
they do not play with the appliance.
• Thewashingmachinemustonlybeusedbyadults,inaccor-
dance with the instructions provided in this manual.
• Donottouchthemachinewhenbarefootorwithwetor
damp hands or feet.
• Donotpullonthepowersupplycablewhenunplugging
the appliance from the electricity socket. Hold the plug
and pull.
• Donotopenthedetergentdispenserdrawerwhilethe
machine is in operation.
• Donottouchthedrainedwaterasitmayreachextreme-
ly high temperatures.
• Neverforcetheportholedoor.Thiscoulddamagethe
safety lock mechanism designed to prevent accidental
opening.
• Iftheappliancebreaksdown,donotunderanycircum-
stances access the internal mechanisms in an attempt
to repair it yourself.
• Alwayskeepchildrenwellawayfromtheappliancewhile
it is operating.
• Thedoorcanbecomequitehotduringthewashcycle.
• Iftheappliancehastobemoved,workinagroupoftwo
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
• Beforeloadinglaundryintothewashingmachine,make
sure the drum is empty.
Load balancing system
Before every spin cycle, to avoid excessive vibrations and
to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the
washing rotation speed. If, after several attempts, the load is
not balanced correctly, the machine spins at a reduced spin
speed. If the load is excessively unbalanced, the washing ma-
chine performs the distribution process instead of spinning.
To encourage improved load distribution and balance, we
recommend small and large garments are mixed in the load.
Disposal
• Disposingofthepackagingmaterials:observelocal
regulations so that the packaging may be re-used.
• TheEuropeanDirective2002/96/EConWaste
Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected
separately in order to optimise the recovery and
recycling of the materials they contain and reduce
the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the
product reminds you of your obligation, that when
you dispose of the appliance it must be separately
collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
10
GB
Care and maintenance
2. Unscrew the lid by rota-
ting it anti-clockwise (see
figure): a little water may
trickle out. This is perfectly
normal.
3. Clean the inside thoroughly.
4. Screw the lid back on.
5. Reposition the panel, making sure the hooks are secu-
rely in place before you push it onto the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If there are any
cracks, it should be replaced immediately: during the wash
cycles, water pressure is very strong and a cracked hose
could easily split open.
! Never use second-hand hoses.
Cutting off the water and electricity
supplies
• Turnoffthewatertapaftereverywashcycle.Thiswill
limit wear on the hydraulic system inside the washing
machine and help to prevent leaks.
• Unplugthewashingmachinewhencleaningitanddu-
ring all maintenance work.
Cleaning the washing machine
The outer parts and rubber components of the appliance
can be cleaned using a soft cloth soaked in lukewarm
soapy water. Do not use solvents or abrasives.
Cleaning the detergent dispenser drawer
To remove the drawer, press
lever (1) and pull the drawer
outwards (2) (see figure).
Wash it under running water;
this procedure should be
repeated frequently.
Caring for the door and drum of your
appliance
• Alwaysleavetheportholedoorajarinordertoprevent
unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cleaning pump
which does not require any maintenance. Sometimes,
small items (such as coins or buttons) may fall into the
protective pre-chamber at the base of the pump.
! Make sure the wash cycle has finished and unplug the
appliance.
To access the pre-chamber:
1. Take off the cover panel
on the front of the machine
by first pressing it in the
centre and then pushing
downwards on both sides
until you can remove it (see
figures).
2
1
1
2
3
GB
11
Troubleshooting
Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure
that the problem cannot be not solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not
take in water (the indicator light for
the first wash cycle stage flashes
rapidly).
The washing machine continuously
takes in and drains water.
The washing machine does not
drain or spin.
The washing machine vibrates a lot
during the spin cycle.
The washing machine leaks.
The Functions indicator lights and the
start/pause indicator light flash, while
one of the phase in progress indicator
lights and the door locked indicator
light will remain lit in a fixed manner.
There is too much foam.
Possible causes / Solutions:
• Theapplianceisnotpluggedintothesocketfully,orisnotmakingcontact.
• Thereisnopowerinthehouse.
• Thewashingmachinedoorisnotclosedproperly.
• TheON/OFFbuttonhasnotbeenpressed.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thewatertaphasnotbeenopened.
• Adelayedstarthasbeenset(see “Personalisation”).
• Thewaterinlethoseisnotconnectedtothetap.
• Thehoseisbent.
• Thewatertaphasnotbeenopened.
• Thereisnowatersupplyinthehouse.
• Thepressureistoolow.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thedrainhoseisnotfittedataheightbetween65and100cmfromthefloor
(see “Installation”).
• Thefreeendofthehoseisunderwater(see “Installation”).
• Thewalldrainagesystemisnotfittedwithabreatherpipe.
If the problem persists even after these checks, turn off the water tap, switch
the appliance off and contact the Assistance Service. If the dwelling is on one of
the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special
anti-draining valves are available in shops and help to avoid this inconvenience.
• Thewashcycledoesnotincludedraining:somewashcyclesrequirethedrain
phase to be started manually.
• The“Easyiron”functionisenabled:tocompletethewashcycle,pressthe
START/PAUSE button (“Personalisation”).
• Thedrainhoseisbent(see “Installation”).
• Thedrainageductisclogged.
• Thedrumwasnotunlockedcorrectlyduringinstallation(see “Installation”).
• Thewashingmachineisnotlevel(see “Installation”).
Thewashingmachineistrappedbetweencabinetsandwalls(see “Installation”).
• Thewaterinlethoseisnotscrewedonproperly(see “Installation”).
• Thedetergentdispenserdrawerisblocked(forcleaninginstructions,see
“Care and maintenance”).
• Thedrainhoseisnotfixedproperly(see “Installation”).
• Switchoffthemachineandunplugit,waitforapproximately1minuteand
then switch it back on again.
If the problem persists, contact the Technical Assistance Service.
• Thedetergentisnotsuitableformachinewashing(itshoulddisplaythetext
“for washing machines” or “hand and machine wash”, or the like).
• Toomuchdetergentwasused.
12
GB
Service
Before calling for Assistance:
• Check whether you can solve the problem alone (see “Troubleshooting”);
• Restarttheprogrammetocheckwhethertheproblemhasbeensolved;
• Ifthisisnotthecase,contactanauthorisedTechnicalAssistanceCentreusingthetelephonenumberprovidedonthe
guarantee certificate.
! Always request the assistance of authorised technicians.
Have the following information to hand:
• thetypeofproblem;
• theappliancemodel(Mod.);
• theserialnumber(S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the
front of the appliance by opening the door.
FR
13
Français
Sommaire
Installation, 14-15
Déballage et mise à niveau
Raccordements eau et électricité
Premier cycle de lavage
Caractéristiques techniques
Description du lave-linge et démarrage
d’un programme, 16-17
Bandeau de commandes
Voyants
Démarrage d’un programme
Programmes, 18
Tableau des programmes
Personnalisations, 19
Sélection de la température
Sélection de l’essorage
Options
Produits lessiviels et linge, 20
Tiroir à produits lessiviels
Cycle blanchissage
Triage du linge
Linge ou vêtements particuliers
Précautions et conseils, 21
Sécurité générale
Système d’équilibrage de la charge
Mise au rebut
Entretien et soin, 22
Coupure de l’arrivée d’eau et du courant
Nettoyage du lave-linge
Nettoyage du tiroir à produits lessiviels
Entretien du hublot et du tambour
Nettoyage de la pompe
Contrôle du tuyau d’arrivée de l’eau
Anomalies et remèdes, 23
Assistance, 24
FR
PWC 91271 W
Mode d’emploi
LAVE-LINGE
14
FR
! Conserver ce mode d’emploi pour pouvoir le consulter à
tout moment. En cas de vente, de cession ou de déména-
gement, veiller à ce qu’il suive toujours le lave-linge pour
que son nouveau propriétaire soit informé sur son mode
de optionnement et puisse profiter des conseils correspon-
dants.
! Lire attentivement les instructions: elles fournissent des
conseils importants sur l’installation, l’utilisation et la sécu-
rité de l’appareil.
Déballage et mise à niveau
Déballage
1. Déballer le lave-linge.
2. Contrôler que le lave-linge n’a pas été endommagé
pendant le transport. S’il est abîmé, ne pas le raccorder et
contacter le vendeur.
3. Enlever les 4 vis de
protection servant au tran-
sport, le caoutchouc et la
cale, placés dans la partie
arrière (voir figure).
4. Boucher les trous à l’aide des bouchons plastique
fournis.
5. Conserver toutes ces pièces: il faudra les remonter en
cas de transport du lave-linge.
! Les pièces d’emballage ne sont pas des jouets pour
enfants.
Mise à niveau
1. Installer le lave-linge sur un sol plat et rigide, sans l’ap-
puyer contre des murs, des meubles ou autre.
2. Si le sol n’est pas par-
faitement horizontal, visser
ou dévisser les pieds de
réglage avant (voir figure)
pour niveler l’appareil; son
angle d’inclinaison, mesuré
sur le plan de travail, ne doit
pas dépasser 2°.
Une bonne mise à niveau garantit la stabilité de l’appareil
et évite qu’il y ait des vibrations, du bruit et des déplace-
ments en cours de optionnement. Si la machine est posée
sur de la moquette ou un tapis, régler les pieds de manière
à ce qu’il y ait suffisamment d’espace pour assurer une
bonne ventilation.
Raccordements eau et électricité
Raccordement du tuyau d’arrivée de l’eau
1. Reliez le tuyau d’alimen-
tation en le vissant à un ro-
binet d’eau froide à embout
fileté 3/4 gaz (voir figure).
Faire couler l’eau jusqu’à ce
qu’elle soit limpide et sans
impuretés avant de raccor-
der.
2. Raccorder le tuyau
d’arrivée de l’eau au lave-
linge en le vissant à la prise
d’eau prévue, dans la partie
arrière en haut à droite (voir
figure).
3. Attention à ce que le tuyau ne soit pas plié ou écrasé.
! La pression de l’eau doit être comprise entre les valeurs
indiquées dans le tableau des Caractéristiques techniques
(voir page ci-contre).
! Si la longueur du tuyau d’alimentation ne suffit pas,
s’adresser à un magasin spécialisé ou à un technicien
agréé.
! N’utiliser que des tuyaux neufs.
! Utiliser ceux qui sont fournis avec l’appareil.
Installation
FR
15
Raccordement du tuyau de vidange
Raccorder le tuyau d’éva-
cuation, sans le plier, à un
conduit d’évacuation ou
à une évacuation murale
placés à une distance du
sol comprise entre 65 et
100 cm;
ou bien l’accrocher à un
évier ou à une baignoi-
re, dans ce cas, fixer le
support en plastique fourni
avec l’appareil au robinet
(voir figure). L’extrémité
libre du tuyau d’évacuation
ne doit pas être plongée
dans l’eau.
! L’utilisation d’un tuyau de rallonge est absolument
déconseillée mais si on ne peut faire autrement, il faut
absolument qu’il ait le même diamètre que le tuyau original
et sa longueur ne doit pas dépasser 150 cm.
Branchement électrique
Avant de brancher la fiche dans la prise de courant, s’as-
surer que:
• lapriseestbienreliéeàlaterreetestconformeaux
réglementations en vigueur;
• lapriseestbienapteàsupporterlapuissancemaximale
de l’appareil indiquée dans le tableau des Caractéristi-
ques techniques (voir ci-contre);
• latensiond’alimentationestbiencompriseentreles
valeurs figurant dans le tableau des Caractéristiques
techniques (voir ci-contre);
• lapriseestbiencompatibleaveclafichedulave-linge.
Autrement, remplacer la prise ou la fiche.
! Le lave-linge ne doit pas être installé dehors, même à
l’abri, car il est très dangereux de le laisser exposé à la
pluie et aux orages.
! Après installation du lave-linge, la prise de courant doit
être facilement accessible.
! N’utiliser ni rallonges ni prises multiples.
! Le câble ne doit être ni plié ni trop écrasé.
! Le câble d’alimentation ne doit être remplacé que par
des techniciens agréés.
Attention! Nous déclinons toute responsabilité en cas de
non-respect des normes énumérées ci-dessus.
Premier cycle de lavage
Avant la première mise en service de l’appareil, effectuer
un cycle de lavage avec un produit lessiviel mais sans linge
et sélectionner le programme 2.
65 - 100 cm
Caractéristiques techniques
Modèle
PWC 91271 W
Dimensions
largeur 59,5 cm
hauteur 85 m
profondeur 60 cm
Capacité
de 1 à 9 kg
Raccordements
électriques
Voir la plaque signalétique appliquée
sur la machine
Raccordements
hydrauliques
pression maximale 1 MPa (10 bar)
pression minimale 0,05 MPa (0,5
bar) capacité du tambour 62 litres
Vitesse d’esso-
rage
jusqu’à 1200 tours minute
Programmes
d’essais selon
la directive
2010/1061
Programme 2.
Température 60°C et 40°C.
Programmes
d’essais selon la
directive
EN 60456
programme 2; température 60°C;
effectué avec une charge de 9 kg.
Cet appareil est conforme aux Di-
rectives Communautaires suivantes:
- 2004/108/CE (Compatibilité élec-
tromagnétique)
- 2006/95/CE (Basse Tension)
- 2002/96/CE
TRRUCH
16
FR
Tiroir à produits lessiviels: pour charger les produits
lessiviels et les additifs (voir “Produits lessiviels et linge”).
Touche ON/OFF: pour allumer ou éteindre le lave-linge.
Bouton PROGRAMMES: pour sélectionner les program-
mes. Pendant le programme, le bouton ne tournera pas.
Touches avec voyants OPTION: pour sélectionner les
options disponibles. Le voyant correspondant à la option
sélectionnée restera allumé.
Touche TEMPÉRATURE: pour sélectionner la températu-
re ou un lavage à froid (voir “Personnalisations”).
Touche ESSORAGE: pour sélectionner l’essorage ou le
supprimer (voir “Personnalisations”).
Touche DÉPART DIFFÉRÉ: pour différer la mise en
marche de votre machine jusqu’à 9 heures. Appuyer plu-
sieurs fois de suite sur la touche jusqu’à ce que le voyant
correspondant au retard souhaité s’allume. A la quatrième
pression sur la touche, l’option se désactive.
N.B.: Après avoir appuyé sur la touche START/PAUSE, le
retard programmé ne peut être modifié que pour le dimi-
nuer jusqu’à lancer le programme sélectionné.
! Il est activé avec tous les programmes.
Voyants DÉROULEMENT CYCLE: pour suivre le stade
d’avancement du programme de lavage.
Le voyant allumé indique la phase de lavage en cours.
Voyant HUBLOT VERROUILLÉ: indique si la porte est
verrouillée (voir page ci-contre).
Touche avec voyant START/PAUSE: pour démarrer les
programmes ou les interrompre momentanément.
N.B.: pour effectuer une pause du lavage en cours, appu-
yer sur cette touche, le voyant correspondant se mettra à
clignoter en orange tandis que celui de la phase en cours
restera allumé fixe. Si le voyant HUBLOT VERROUILLÉ
est éteint, on peut ouvrir la porte (3 minutes environ).
Pour faire redémarrer le lavage exactement de l’endroit où
il a été interrompu, appuyer une nouvelle fois sur la touche.
Stand-by
Ce lave-linge, conformément aux nouvelles normes en
vigueur dans le domaine de l’économie d’énergie, est équi-
pée d’un système d’extinction automatique (veille) acti
après 30 minutes environ d’inutilisation. Appuyez briève-
ment sur la touche ON/OFF et attendre que la machine soit
réactivée.
Description du lave-linge et
démarrage d’un programme
Voyants DÉROULEMENT
CYCLE
Voyant
HUBLOT
VERROUILLÉ
Touche
avec voyant
START/
PAUSE
Bandeau de commandes
Tiroir à produits lessiviels
Touche ON/OFF
Bouton
PROGRAMMES
Touche
DÉPART
DIFFÉRÉ
VOYANTS
Touche
TEMPÉRATURE
Touche
ESSORAGE
Touches avec voyants
OPTION
FR
17
Voyants
Les voyants fournissent des informations importantes.
Voilà ce qu’ils signalent:
Départ différé
Si la option “Départ différé” a été activée (voir “Personnali-
sations”), le voyant correspondant au temps sélectionné se
mettra à clignoter, après avoir lancé le programme:
Au fur et à mesure que le temps passe, le temps restant
est affiché avec clignotement du voyant correspondant.
Quand le retard sélectionné touche à sa fin le programme
sélectionné démarre.
Voyants phase en cours
Une fois que le cycle de lavage sélectionné a démarré,
les voyants s’allument progressivement pour indiquer son
stade d’avancement:
Touches options et voyants correspondants
La sélection d’une option entraîne l’allumage du voyant
correspondant.
Si la option sélectionnée est incompatible avec le program-
me sélectionné, le voyant correspondant se met à clignoter
et la option n’est pas activée.
Si l’option sélectionnée est incompatible avec une autre
option précédemment sélectionnée, le voyant correspon-
dant à la première option se met à clignoter et seule la
deuxième option est activée, le voyant de la touche s’allu-
me au fixe.
Remarque: si l’option
est activée, aucune autre option
non compatible ne pourra être activée.
Voyant hublot verrouillé
Le voyant allumé indique que le hublot est verrouillé pour
en empêcher l’ouverture. Attendre que le voyant cesse de
clignoter avant d’ouvrir la porte (3 minutes environ).
Pour ouvrir le hublot tandis qu’un cycle est en cours, ap-
puyer sur la touche START/PAUSE; si le voyant HUBLOT
VERROUILLÉ est éteint, on peut ouvrir le hublot.
! Le clignotement rapide des voyants des “Foncptions” et
du voyant START/PAUSE en même temps que l’alluma-
ge des voyants de la “phase de lavage en cours” et du
HUBLOT VERROUILLÉ signalent une anomalie (consulter
“Anomalies et remèdes”).
Démarrage d’un programme
1. Allumer le lave-linge en appuyant sur la touche ON/OFF. Tous les voyants s’allumeront pendant quelques secondes, ne
resteront ensuite allumés que les voyants correspondant aux sélections du programme en cours et le voyant START/PAUSE
se mettra à clignoter.
2. Charger le linge et fermer le hublot.
3. Sélectionner à l’aide du bouton PROGRAMMES le programme désiré.
4. Sélectionner la température de lavage (voir “Personnalisations”).
5. Sélectionner la vitesse d’essorage (voir “Personnalisations”).
6. Verser les produits lessiviels et les additifs (voir “Produits lessiviels et linge”).
7. Sélectionner les options désirées.
8. Appuyer sur la touche START/PAUSE pour démarrer le programme, le voyant correspondant bleu restera allumé en fixe.
Pour annuler le cycle sélectionné, appuyer sur la touche START/PAUSE pour placer l’appareil en pause et choisir un nouve-
au cycle.
9. A la fin du programme, le voyant END s’allume. Quand le voyant HUBLOT VERROUILLÉ
s’éteint, on peut ouvrir le
hublot (3 minutes environ). Sortir le linge et laisser le hublot entrouvert pour faire sécher le tambour.
Eteindre le lave-linge en appuyant sur la touche ON/OFF.
Lavage
Rinçage
Essorage
Vidange
Fin de Lavage
Voyants DÉROULEMENT
CYCLE
END
18
FR
Programmes
Description du Programme
Temp.
max.
(°C)
Vitesse
maxi
(tours
minute)
Produit lessiviel et additifs
Charge
maxi
(Kg)
Durée
cycle
Pré-
lavage
Lavage Javel
Adou-
cissant
Programmes Quotidiens
1
Coton avec prélavage: blancs extrêmement sales. 90° 1200
-
9 195
2
Coton blanc: blancs très sales. 90° 1200 -
9 180
2
Coton blanc (1): blancs et couleurs résistantes très sales. 60° 1200 -
9 190
2
Coton blanc (1-2): blancs et couleurs délicates peu sales. 40° 1200 -
9 165
3
Coton: blancs et couleurs résistantes très sales. 60° 1200 -
9 140
4
Coton couleurs (3): blancs peu sales et couleurs délicates. 40° 1200 -
9 100
5
Synthétique: couleurs résistantes très sales. 60° 800 -
4 90
6
Jeans
40° 800 -
-
4 70
7
Chemises
40° 600 -
2 70
8
Mix-Froid 30’: pour rafraîchir rapidement du linge peu sale
(ne convient pas pour la laine, la soie et le linge à laver à la main).
Eau
froid
800 -
-
3 30
Programmes Spéciaux
9
Laine: pour laine, cachemire, etc. 40° 600 -
-
2 55
10
Soie: pour linge en soie, viscose, lingerie. 30° 0 -
-
2 70
11
Duvets
30° 1000 -
-
3 120
12
Outwear
30° 600 -
- - 2,5 60
13
Baskets
30° 600 -
-
Max.2
paires
60
Fonctions
Rinçage - 1200 - -
9 35
Essorage - 1200 - - - - 9 15
Vidange - 0 - - - - 9 2
Programmes
Tableau des programmes
La durée du cycle indiquée sur l’écran ou dans la notice représente une estimation calculée dans des conditions standard. Le temps effectif peut varier en fonction de
nombreux facteurs tels que : température et pression de l’eau en entrée, température ambiante, quantité de lessive, quantité et type de charge, équilibrage de la charge,
options supplémentaires sélectionnées.
Pour tous les instituts qui effectuent ces tests :
1) Programme de contrôle selon la norme 2010/1061: sélectionner le programme 2 et une température de 60°C et 40°C.
2) Programme coton long: sélectionner le programme 2 et une température de 40°C.
3) Programme coton court: sélectionner le programme 4 et une température de 40°C.
1) Programme de contrôle selon la norme EN 60456: sélectionner le programme 2 et une température de 60°C.
TRRUCH
FR
19
Sélection de la température
Appuyer sur la touche TEMPÉRATURE pour sélectionner la température de lavage (voir Tableau des programmes).
La température peut être abaissée jusqu’au lavage à froid (
).
La machine interdira automatiquement toute sélection d’une température supérieure à la température maximale prévue pour
chaque programme.
Sélection de l’essorage
Appuyer sur la touche ESSORAGE pour sélectionner la vitesse d’essorage du programme sélectionné.
Les vitesses maximales prévues pour les programmes sont:
Programmes Vitesse maximale
Coton 1200 tours/minute
Synthétiques 800 tours/minute
Laine 600 tours/minute
Soie vidange seule
La vitesse d’essorage peut être réduite ou l’essorage supprimé en sélectionnant le symbole
.
La machine interdira automatiquement tout essorage à une vitesse supérieure à la vitesse maximale prévue pour chaque
programme.
Options
Les différentes options de lavage prévues par le lave-linge permettent d’obtenir la propreté et le blanc souhaités.
Pour activer les options:
1. appuyer sur la touche correspondant à la option désirée;
2. l’allumage du voyant correspondant signale que la option est activée.
Remarque: Le clignotement rapide du voyant signale que la option correspondante n’est pas disponible pour le programme
sélectionné.
La technologie de «PRIME» ajuste les consommations d’eau, d’électricité et la durée de lavage en fonction de la charge
effective de linge.
Une pression sur la touche
permet en outre de sélectionner l’option:
- Water (Eau): pour réduire la consommation d’eau sans pour autant renoncer à des résultats impeccables (conseillée pour
du linge très sale).
- Energy (Énergie): cette option, sélectionnée en automatique par «PRIME», réduit la consommation d’électricité (conseillée
pour du linge normalement sale).
- Time (Temps): pour réduire la durée de lavage (conseillée pour du linge peu sale).
! Il n’est activable que sur les programmes 1, 2, 3, 4, 5 (les trois niveaux) et 6, 7, 8 (niveaux - Energy et - Time).
Rinçage Plus
La sélection de cette option permet d’augmenter l’efficacité du rinçage et d’éliminer totalement toute trace de lessive. Elle est
très utile en cas de peaux particulièrement sensibles.
! Elle n’est pas activable sur les programmes 8, , .
Repassage facile
En cas de sélection de cette option, le lavage et l’essorage seront dûment modifiés pour réduire le froissement. En fin de
cycle, le lave-linge fait tourner le tambour lentement, le voyant de l’option REPASSAGE FACILE et celui de START/PAUSE se
mettent à clignoter (le premier est bleu, le deuxième est ambre). Pour compléter le cycle, il faut appuyer sur la touche START/
PAUSE ou sur la touche REPASSAGE FACILE. Pour les programmes 10-12 l’appareil arrive au bout du cycle en laissant le
linge tremper, le voyant REPASSAGE FACILE et celui de START/PAUSE se mettent à clignoter. Pour vidanger l’eau et pouvoir
sortir le linge, il faut appuyer sur la touche START/PAUSE ou sur la touche REPASSAGE FACILE.
! Elle n’est pas activable sur les programmes 8, 9, 13, , .
Anti-tâches
Cycle de anti-tâches conseillé pour l’élimination de taches très résistantes. N’oubliez pas de verser l’eau de Javel dans le bac
supplémentaire 4 (voir “Cycle blanchissage”).
! Elle n’est pas activable sur les programmes 1, 6, 8, 9, 10, 11, 12, 13, , .
Personnalisations
20
FR
Produits lessiviels et linge
Tiroir à produits lessiviels
Un bon résultat de lavage dépend aussi d’un bon dosage de
produit lessiviel: un exs de lessive ne lave pas mieux, il incru-
ste l’intérieur du lave-linge et pollue lenvironnement.
! Ne pas utiliser de lessives pour lavage à la main, elles
moussent trop.
Sortir le tiroir à produits les-
siviels et verser la lessive ou
l’additif comme suit.
Bac 1 : Lessive prélavage
(en poudre)
Avant d’introduire la lessive,
s’assurer que le bac supplé-
mentaire 4 n’est pas présent.
Bac 2 : Lessive lavage
(en poudre ou liquide)
Verser la lessive liquide juste avant la mise en marche.
Bac 3 : Additifs (assouplissant, etc.)
L’assouplissant ne doit pas déborder de la grille.
Bac supplémentaire 4 : Javel
! N’utilisez pas de lessives pour lavage à la main, elles
génèrent trop de mousse.
Cycle blanchissage
! N’utilisez de l’eau de Javel traditionelle que pour les
tissus blancs résistants et des détachants délicats pour
les couleurs, les synthétiques et la laine.
Montez le bac supplémentaire 4 fourni avec l’appareil à l’inté-
rieur du bac 1. Lorsque vous versez leau de Javel, attention à
ne pas dépasser le niveau max” indiq sur le pivot central (voir
figure). Pour blanchir uniquement, versez leau de Javel dans le
bac supplémentaire 4, lectionnez le programme «Rinçag
et activez le option «Anti-tâches»
. Pour blanchir en cours de
lavage, versez le produit lessiviel et les additifs, sélectionnez le
programme souhaité et activez le option «Anti-ches»
.
L’utilisation du bac supplémentaire 4 exclut le prélavage.
Triage du linge
• Triercorrectementlelinged’après:
- le type de textile / le symbole sur l’étiquette.
- les couleurs: séparer le linge coloré du blanc.
• Viderlespochesetcontrôlerlesboutons.
• Nepasdépasserlesvaleursindiquéescorrespondantau
poids de linge sec :
Textiles résistants: 9 kg max.
Textiles synthétiques: 4 kg max.
Textiles délicats: 2 kg max.
Laine: 2 kg max.
Soie: 2 kg max.
Combien pèse le linge ?
1 drap 400-500 g
1 taie d’oreiller 150-200 g
1 nappe 400-500 g
1 peignoir 900-1200 g
1 serviette éponge 150-250 g
Linge ou vêtements particuliers
Jeans: mettez les jeans à l’envers avant de les laver et
utilisez une lessive liquide. Sélectionnez le programme 6.
Chemises: sélectionner le programme approprié au
lavage de chemises 7 pour laver des chemises de textile et
couleur différents.
Mix Froid 30’: il est spécialement conçu pour laver des
vêtements peu sales en un rien de temps : il ne dure que
30 minutes et permet ainsi de faire des économies d’éner-
gie et de temps. La sélection de ce programme 8 permet
de laver à froid des textiles différents (sauf laine et soie) en
ne dépassant pas 3 kg de charge.
Laine: grâce au programme 9 vous pouvez laver à la
machine tous vos vêtements en laine, y compris ceux qui
portent l’étiquette “ lavage à la main uniquement “
.
Pour obtenir d’excellents résultats utilisez un produit lessi-
viel spécial et ne dépassez pas une charge de 2 kg.
Soie: sélectionner le programme de lavage spécial 10
pour vêtements en soie. Il est conseillé d’utiliser une lessi-
ve spéciale pour linge délicat.
Voilages: pliez-les bien et glissez-les dans une taie
d’oreiller ou dans un sac genre filet. Sélectionner le pro-
gramme 10.
Duvets: pour laver des articles avec garnissage en duvet
d’oie comme par exemple des couettes deux places ou
une place (poids maximal à ne pas dépasser 3 kg), oreil-
lers, anoraks, utiliser le programme spécial 11 “Duvets”.
Pour introduire les duvets dans le tambour, nous recom-
mandons de replier les bords en dedans (voir figures) et de
ne pas occuper plus de ¾ du volume du tambour. Pour un
lavage optimal, nous recommandons d’utiliser une lessive
liquide à doser dans le tiroir à produits lessiviels.
Outwear (programme 12): est spécialement conçu pour
laver des tissus hydrofuges et des anoraks (par ex.: gore-
tex, polyester, nylon); pour obtenir d’excellents résultats,
utilisez une lessive liquide avec une dose pour la demi-
charge; prétraitez poignets, cols et taches; n’utilisez ni as-
souplissants ni d’autres produits avec assouplissant. Avec
ce programme vous ne pouvez pas laver les duvets.
Baskets (programme 13): est spécialement conçu pour
laver des chaussures de sport; pour obtenir d’excellents
résultats nous recommandons de ne pas en laver plus de
2 paires à la fois.
4
2
3
1
4
2
1
3
1 / 1

Indesit PWC 91271 W (EU) Mode d'emploi

Catégorie
Machines à laver
Taper
Mode d'emploi