Porter-Cable Air Compressor CPFAC2600P Manuel utilisateur

Pancake Compressor

Instruction

manual

The Model and Serial No. plate is located on the main

housing of the tool. Record these numbers in the

spaces below and retain for future reference.

Model No. ______________________________________

Type ___________________________________________

Serial No. _______________________________________

IMPORTANT

Please make certain that the person who is

to use this equipment carefully reads and

understands these instructions before

starting operations.

Part No. D27856-0210-0

ESPAÑOL: PÁGINA 19

FRANÇAISE : PAGE 37

To learn more about Porter-Cable

visit our website at:

http://www.porter-cable.com

MODEL

CPFAC2600P

PROFESSIONAL POWER TOOLS

2 - ENG

D27856

SAFETY GUIDELINES - DEFINITIONS

Indicates an

imminently hazardous

situation which, if not avoided, will

result in death or serious injury.

Indicates a potentially

hazardous situation

which, if not avoided, could

result in

death or serious injury.

Indicates a potentially

hazardous situation

which, if not avoided, may

result in

minor or moderate injury.

Used without the

safety alert symbol

indicates a potentially hazardous

situation which, if not avoided, may

result in property damage

.

This manual contains information that is important for you to know and understand. This information

relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you

recognize this information, we use the symbols below. Please read the manual and pay attention to

these sections.

IMPORTANT SAFETY INSTRUCTIONS

Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known (to the State of California) to

cause cancer, birth defects or other reproductive harm. Some example of these chemicals are:

●

lead from lead-based paints

●

crystalline silica from bricks and cement and other masonry products

●

arsenic and chromium from chemically-treated lumber

Your risk from these exposures varies, depending on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well ventilated area, and work with approved safety

equipment, always wear MSHA/NIOSH approved, properly fitting face mask or respirator when using

such tools.

When using air tools, basic safety precautions should always be followed to reduce the risk of of

personal injury.

READ AND FOLLOW ALL INSTRUCTIONS.

This tool was designed for certain applications. Porter-Cable strongly recommends that this tool NOT

be modified and/or used for any application other than for which it was designed. If you have any

questions relative to its application DO NOT use the tool until you have written Porter-Cable and we

have advised you.

Technical Service Manager

Porter-Cable Corporation

4825 Highway 45 North

P.O. Box 2468

Jackson, TN 38302-2468

3 - ENG

D27856

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

IMPROPER OPERATION OR MAINTENANCE OF THIS PRODUCT COULD RESULT IN

SERIOUS INJURY AND PROPERTY DAMAGE. READ AND UNDERSTAND ALL

WARNINGS AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT.

RISK OF EXPLOSION OR FIRE

ALWAYS OPERATE THE COMPRESSOR IN A

WELL VENTILATED AREA FREE OF

COMBUSTIBLE MATERIALS, GASOLINE OR

SOLVENT VAPORS.

IF SPRAYING FLAMMABLE MATERIALS,

LOCATE COMPRESSOR AT LEAST 20 FEET

AWAY FROM SPRAY AREA. AN ADDITIONAL

LENGTH OF HOSE MAY BE REQUIRED.

STORE FLAMMABLE MATERIALS IN A

SECURE LOCATION AWAY FROM

COMPRESSOR.

NEVER PLACE OBJECTS AGAINST OR ON

TOP OF COMPRESSOR. OPERATE

COMPRESSOR IN AN OPEN AREA AT LEAST

12 INCHES AWAY FROM ANY WALL OR

OBSTRUCTION THAT WOULD RESTRICT THE

FLOW OF FRESH AIR TO THE VENTILATION

OPENINGS.

OPERATE COMPRESSOR IN A CLEAN, DRY,

WELL VENTILATED AREA. DO NOT OPERATE

UNIT INDOORS OR IN ANY CONFINED AREA.

ALWAYS REMAIN IN ATTENDANCE WITH THE

PRODUCT WHEN IT IS OPERATING.

ALWAYS DISCONNECT ELECTRICAL POWER

BY MOVING PRESSURE SWITCH LEVER TO

THE OFF POSITION AND DRAIN TANK DAILY

OR AFTER EACH USE.

HOW TO PREVENT IT

IT IS NORMAL FOR ELECTRICAL CONTACTS

WITHIN THE MOTOR AND PRESSURE SWITCH

TO SPARK.

IF ELECTRICAL SPARKS FROM

COMPRESSOR COME INTO CONTACT WITH

FLAMMABLE VAPORS, THEY MAY IGNITE,

CAUSING FIRE OR EXPLOSION.

RESTRICTING ANY OF THE COMPRESSOR

VENTILATION OPENINGS WILL CAUSE

SERIOUS OVERHEATING AND COULD CAUSE

FIRE.

UNATTENDED OPERATION OF THIS

PRODUCT COULD RESULT IN PERSONAL

INJURY OR PROPERTY DAMAGE. TO

REDUCE THE RISK OF FIRE, DO NOT ALLOW

THE COMPRESSOR TO OPERATE

UNATTENDED.

WHAT CAN HAPPEN

HAZARD

4 - ENG

D27856

HAZARD

RISK OF BURSTING

AIR TANK: THE FOLLOWING CONDITIONS COULD LEAD TO A WEAKENING OF

THE TANK, AND RESULT IN A VIOLENT TANK EXPLOSION AND COULD CAUSE

PROPERTY DAMAGE OR SERIOUS INJURY.

HOW TO PREVENT IT

WHAT CAN HAPPEN

DRAIN TANK DAILY OR AFTER EACH USE. IF

TANK DEVELOPS A LEAK, REPLACE IT

IMMEDIATELY WITH A NEW TANK OR REPLACE

THE ENTIRE COMPRESSOR.

NEVER DRILL INTO, WELD, OR MAKE ANY

MODIFICATIONS TO THE TANK OR ITS

ATTACHMENTS.

THE TANK IS DESIGNED TO WITHSTAND

SPECIFIC OPERATING PRESSURES. NEVER

MAKE ADJUSTMENTS OR PARTS

SUBSTITUTIONS TO ALTER THE FACTORY

SET OPERATING PRESSURES.

FOR ESSENTIAL CONTROL OF AIR

PRESSURE,YOU MUST INSTALL A PRESSURE

REGULATOR AND PRESSURE GAUGE TO THE

AIR OUTLET (IF NOT EQUIPPED) OF YOUR

COMPRESSOR. FOLLOW THE EQUIPMENT

MANUFACTURERS RECOMMENDATION AND

NEVER EXCEED THE MAXIMUM ALLOWABLE

PRESSURE RATING OF ATTACHMENTS.

NEVER USE COMPRESSOR TO INFLATE

SMALL LOW-PRESSURE OBJECTS SUCH AS

CHILDREN’S TOYS, FOOTBALLS,

BASKETBALLS, ETC.

1. FAILURE TO PROPERLY DRAIN

CONDENSED WATER FROM THE

TANK, CAUSING RUST AND THINNING

OF THE STEEL TANK.

2. MODIFICATIONS OR ATTEMPTED

REPAIRS TO THE TANK.

3. UNAUTHORIZED MODIFICATIONS TO

THE UNLOADER VALVE, SAFETY

VALVE, OR ANY OTHER COMPONENTS

WHICH CONTROL TANK PRESSURE.

4. EXCESSIVE VIBRATION CAN WEAKEN

THE AIR TANK AND CAUSE RUPTURE

OR EXPLOSION.

ATTACHMENTS & ACCESSORIES:

EXCEEDING THE PRESSURE RATING OF AIR

TOOLS, SPRAY GUNS, AIR OPERATED

ACCESSORIES, TIRES AND OTHER

INFLATABLES CAN CAUSE THEM TO

EXPLODE OR FLY APART, AND COULD

RESULT IN SERIOUS INJURY.

HAZARD

RISK FROM FLYING OBJECTS

HOW TO PREVENT IT

WHAT CAN HAPPEN

THE COMPRESSED AIR STREAM CAN

CAUSE SOFT TISSUE DAMAGE TO EXPOSED

SKIN AND CAN PROPEL DIRT, CHIPS, LOOSE

PARTICLES AND SMALL OBJECTS AT HIGH

SPEED, RESULTING IN PROPERTY DAMAGE

OR PERSONAL INJURY.

ALWAYS WEAR ANSI Z87.1 APPROVED

SAFETY GLASSES WITH SIDE SHIELDS WHEN

USING THE COMPRESSOR.

NEVER POINT ANY NOZZLE OR SPRAYER

TOWARD ANY PART OF THE BODY OR AT

OTHER PEOPLE OR ANIMALS.

ALWAYS TURN THE COMPRESSOR OFF AND

BLEED PRESSURE FROM THE AIR HOSE AND

TANK BEFORE ATTEMPTING MAINTENANCE,

ATTACHING TOOLS OR ACCESSORIES.

5 - ENG

D27856

HAZARD

HOW TO PREVENT IT

WHAT CAN HAPPEN

RISK TO BREATHING

AIR OBTAINED DIRECTLY FROM THE

COMPRESSOR SHOULD NEVER BE USED TO

SUPPLY AIR FOR HUMAN CONSUMPTION. IN

ORDER TO USE AIR PRODUCED BY THIS

COMPRESSOR FOR BREATHING, SUITABLE

FILTERS AND IN-LINE SAFETY EQUIPMENT

MUST BE PROPERLY INSTALLED. IN-LINE

FILTERS AND SAFETY EQUIPMENT USED IN

CONJUNCTION WITH THE COMPRESSOR

MUST BE CAPABLE OF TREATING AIR TO

ALL APPLICABLE LOCAL AND FEDERAL

CODES PRIOR TO HUMAN CONSUMPTION.

WORK IN AN AREA WITH GOOD CROSS-

VENTILATION. READ AND FOLLOW THE

SAFETY INSTRUCTIONS PROVIDED ON THE

LABEL OR SAFETY DATA SHEETS FOR THE

MATERIAL YOU ARE SPRAYING. USE A

NIOSH/MSHA APPROVED RESPIRATOR

DESIGNED FOR USE WITH YOUR SPECIFIC

APPLICATION.

THE COMPRESSED AIR DIRECTLY FROM

YOUR COMPRESSOR IS NOT SAFE FOR

BREATHING. THE AIR STREAM MAY

CONTAIN CARBON MONOXIDE, TOXIC

VAPORS, OR SOLID PARTICLES FROM THE

TANK. BREATHING THESE CONTAMINANTS

CAN CAUSE SERIOUS INJURY OR DEATH.

SPRAYED MATERIALS SUCH AS PAINT,

PAINT SOLVENTS, PAINT REMOVER,

INSECTICIDES, WEED KILLERS, MAY

CONTAIN HARMFUL VAPORS AND POISONS.

RISK OF ELECTRICAL SHOCK

HOW TO PREVENT IT

WHAT CAN HAPPEN

YOUR AIR COMPRESSOR IS POWERED BY

ELECTRICITY. LIKE ANY OTHER

ELECTRICALLY POWERED DEVICE, IF IT IS

NOT USED PROPERLY IT MAY CAUSE

ELECTRIC SHOCK.

REPAIRS ATTEMPTED BY UNQUALIFIED

PERSONNEL CAN RESULT IN SERIOUS

INJURY OR DEATH BY ELECTROCUTION.

ELECTRICAL GROUNDING: FAILURE TO

PROVIDE ADEQUATE GROUNDING TO THIS

PRODUCT COULD RESULT IN SERIOUS

INJURY OR DEATH FROM ELECTROCUTION.

SEE GROUNDING INSTRUCTIONS.

NEVER OPERATE THE COMPRESSOR

OUTDOORS WHEN IT IS RAINING OR IN WET

CONDITIONS.

NEVER OPERATE COMPRESSOR WITH

PROTECTIVE COVERS REMOVED OR

DAMAGED.

ANY ELECTRICAL WIRING OR REPAIRS

REQUIRED ON THIS PRODUCT SHOULD BE

PERFORMED BY AUTHORIZED SERVICE

CENTER PERSONNEL IN ACCORDANCE WITH

NATIONAL AND LOCAL ELECTRICAL CODES.

MAKE CERTAIN THAT THE ELECTRICAL

CIRCUIT TO WHICH THE COMPRESSOR IS

CONNECTED PROVIDES PROPER

ELECTRICAL GROUNDING, CORRECT

VOLTAGE AND ADEQUATE FUSE

PROTECTION.

6 - ENG

D27856

HAZARD

HOW TO PREVENT IT

WHAT CAN HAPPEN

RISK OF BURNS

TOUCHING EXPOSED METAL SUCH AS THE

COMPRESSOR HEAD OR OUTLET TUBES,

CAN RESULT IN SERIOUS BURNS.

NEVER TOUCH ANY EXPOSED METAL

PARTS ON COMPRESSOR DURING OR

IMMEDIATELY AFTER OPERATION.

COMPRESSOR WILL REMAIN HOT FOR

SEVERAL MINUTES AFTER OPERATION.

DO NOT REACH AROUND PROTECTIVE

SHROUDS OR ATTEMPT MAINTENANCE

UNTIL UNIT HAS BEEN ALLOWED TO COOL.

HAZARD

HOW TO PREVENT IT

WHAT CAN HAPPEN

RISK FROM MOVING PARTS

NEVER OPERATE THE COMPRESSOR WITH

GUARDS OR COVERS WHICH ARE DAMAGED

OR REMOVED.

ANY REPAIRS REQUIRED ON THIS PRODUCT

SHOULD BE PERFORMED BY AUTHORIZED

SERVICE CENTER PERSONNEL.

MOVING PARTS SUCH AS THE PULLEY,

FLYWHEEL AND BELT CAN CAUSE SERIOUS

INJURY IF THEY COME INTO CONTACT WITH

YOU OR YOUR CLOTHING.

ATTEMPTING TO OPERATE COMPRESSOR

WITH DAMAGED OR MISSING PARTS OR

ATTEMPTING TO REPAIR COMPRESSOR

WITH PROTECTIVE SHROUDS REMOVED CAN

EXPOSE YOU TO MOVING PARTS AND CAN

RESULT IN SERIOUS INJURY.

HAZARD

HOW TO PREVENT IT

WHAT CAN HAPPEN

HAZARD

HOW TO PREVENT IT

WHAT CAN HAPPEN

RISK OF FALLING

A PORTABLE COMPRESSOR CAN FALL

FROM A TABLE, WORKBENCH OR ROOF

CAUSING DAMAGE TO THE COMPRESSOR

AND COULD RESULT IN SERIOUS INJURY

OR DEATH TO THE OPERATOR.

ALWAYS OPERATE COMPRESSOR IN A

STABLE SECURE POSITION TO PREVENT

ACCIDENTAL MOVEMENT OF THE UNIT.

NEVER OPERATE COMPRESSOR ON A ROOF

OR OTHER ELEVATED POSITION. USE

ADDITIONAL AIR HOSE TO REACH HIGH

LOCATIONS.

RISK OF PROPERTY DAMAGE WHEN TRANSPORTING COMPRESSOR

OIL CAN LEAK OR SPILL AND COULD

RESULT IN FIRE OR BREATHING HAZARD,

SERIOUS INJURY OR DEATH CAN RESULT.

OIL LEAKS WILL DAMAGE CARPET, PAINT OR

OTHER SURFACES IN VEHICLES OR

TRAILERS.

ALWAYS PLACE COMPRESSOR ON A

PROTECTIVE MAT WHEN TRANSPORTING TO

PROTECT AGAINST DAMAGE TO VEHICLE

FROM LEAKS. REMOVE COMPRESSOR FROM

VEHICLE IMMEDIATELY UPON ARRIVAL AT

YOUR DESTINATION.

(Fire, Inhalation, Damage to Vehicle Surfaces)

7 - ENG

D27856

HAZARD

HOW TO PREVENT IT

WHAT CAN HAPPEN

RISK OF UNSAFE OPERATION

REVIEW AND UNDERSTAND ALL

INSTRUCTIONS AND WARNINGS IN THIS

MANUAL.

BECOME FAMILIAR WITH THE OPERATION

AND CONTROLS OF THE AIR COMPRESSOR.

KEEP OPERATING AREA CLEAR OF ALL

PERSONS, PETS, AND OBSTACLES.

KEEP CHILDREN AWAY FROM THE AIR

COMPRESSOR AT ALL TIMES.

DO NOT OPERATE THE PRODUCT WHEN

FATIGUED OR UNDER THE INFLUENCE OF

ALCOHOL OR DRUGS. STAY ALERT AT ALL

TIMES.

NEVER DEFEAT THE SAFETY FEATURES OF

THIS PRODUCT.

EQUIP AREA OF OPERATION WITH A FIRE

EXTINGUISHER.

DO NOT OPERATE MACHINE WITH MISSING,

BROKEN, OR UNAUTHORIZED PARTS.

UNSAFE OPERATION OF YOUR AIR

COMPRESSOR COULD LEAD TO SERIOUS IN-

JURY OR DEATH TO YOU OR OTHERS.

8 - ENG

D27856

GLOSSARY

SCFM or CFM: Standard Cubic Feet per Minute; a unit of measurement of air

delivery.

PSIG or PSI: Pounds per square inch gauge.

CUT-IN PRESSURE: While the motor is off, air tank pressure drops as you

continue to use your accessory or air tool. When the tank pressure drops to a

certain low level the motor will restart automatically. The low pressure at which

the motor automatically restarts is called “cut-in pressure.”

CUT-OUT PRESSURE: When you turn on your air compressor and it begins to

run, air pressure in the air tank begins to build. It builds to a certain high pressure

before the motor automatically shuts off - protecting your air tank from pressure

higher than its capacity. The high pressure at which the motor shuts off is called

“cut-out pressure.”

CODE CERTIFICATION: Products that bear one or more of the following marks:

UL, CUL, ETL, CETL, have been evaluated by OSHA certified indepenent safety

laboratories and meet the applicable Underwriters Laboratories Standards for

Safety.

DUTY CYCLE

Porter-Cable air compressors should be operated on not more than a 50% duty

cycle. This means an air compressor that pumps air more than 50% of one hour

is considered misused, because the air compressor is undersized for the required

air demand. Maximum compressor pumping time per hour is 30 minutes.

SPECIFICATIONS

MODEL NO. CPFAC2600P

Horsepower-Peak 2.0

SCFM @ 40 psig 3.7

SCFM @ 90 psig 2.6

Cut-In 120 PSI

Cut-Out 150 PSI

Bore 1.875"

Stroke 1.250"

Voltage/Hertz/Phase 120/60/1

Minimum Branch Circuit 15 Amp

* Fuse Type Time Delay

Amperage at Max. Load 10 Amps

Tank Size 6 Gallon

* A circuit breaker is preferred. Use only a fuse or circuit breaker that is the same

rating as the branch circuit on which the air compressor is operated. If

compressor is connected to a circuit protected by fuses, use only time delay

fuses. Time delay fuses should be marked “D” in Canada and “T” in the US.

9 - ENG

D27856

HOW TO SET UP YOUR UNIT

Location of the Air Compressor

Locate the air compressor in a clean, dry and well ventilated area. The air

compressor should be located at least 12" away from the wall or other

obstructions that will interfere with the flow of air. The air compressor pump and

shroud are designed to allow for proper cooling. The ventilation openings on the

compressor are necessary to maintain proper operating temperature. Do not

place rags or other containers on or near these openings.

GROUNDING INSTRUCTIONS

RISK OF ELECTRICAL SHOCK. In the event of a short

circuit, grounding reduces the risk of shock by providing an

escape wire for the electric current. This air compressor must be properly

grounded.

The portable air compressor is equipped with a cord having a grounding wire

with an appropriate grounding plug (see following illustrations). The plug must

be used with an outlet that has been installed and grounded in accordance with

all local codes and ordinances.

1. The cord set and plug with this unit contains a grounding pin. This plug

MUST be used with a grounded outlet.

IMPORTANT: The outlet being used must

be installed and grounded in accordance

with all local codes and ordinances.

2. Make sure the outlet being used has

the same configuration as the

grounded plug. DO NOT USE AN

ADAPTER. See illustration.

3. Inspect the plug and cord before each use. Do not use if there are signs of

damage.

4. If these grounding instructions are not completely understood, or if in doubt

as to whether the compressor is properly grounded, have the installation

checked by a qualified electrician.

IMPROPER GROUNDING CAN RESULT IN ELECTRICAL

SHOCK. Do not modify the plug provided. If it does not fit

the available outlet, a correct outlet should be installed by a qualified

electrician. Repairs to the cord set or plug MUST be made by a qualified

electrician.

Grounding Pin

Grounded

Outlets

Plug

INSTALLATION

10 - ENG

D27856

Extension Cords

Using extension cords is not recommended. The use of extension cords will

cause voltage to drop resulting in power loss to the motor and overheating.

Attach extra air hoses at the air outlet instead of using extension cords.

If an extension cord must be used, be sure it is:

• a 3-wire extension cord that has a 3-blade grounding plug, and a 3-slot

receptacle that will accept the plug on the product

• in good condition

• no longer than 50 feet

• 12 gauge (AWG) or larger. (Wire size increases as gauge number

decreases. 10 AWG and 8 AWG may also be used. DO NOT USE 14 OR

16 AWG.)

Voltage and Circuit Protection

Refer to the Specification Chart for the voltage and minimum branch circuit

requirements.

Certain air compressors can be operated on a 15 amp circuit if the following

conditions are met.

1. Voltage supply through branch circuit is 15 amps.

2. Circuit is not used to supply any other electrical needs (lights, appliances,

etc.).

3. Extension cords comply with specifications.

4. Circuit is equipped with a 15 amp circuit breaker or 15 amp time delay

fuse. NOTE: If compressor is connected to a circuit protected by fuses,

use only time delay fuses. Time delay fuses should be marked "D" in

Canada and "T" in the US.

If any of the above conditions cannot be met, or if operation of the compressor

repeatedly causes interruption of the power, it may be necessary to operate it

from a 20 amp circuit. It is not necessary to change the cord set.

11 - ENG

D27856

DESCRIPTION OF OPERATION

Description of Operation

Become familiar with these controls before operating the unit.

On/Auto/Off Switch: Turn this switch ON to provide automatic power to the

pressure switch and OFF to remove power at the end of each use.

Pressure Switch: The pressure switch automatically starts the motor when the

air tank pressure drops below the factory set "cut-in” pressure. It stops the

motor when the air tank pressure reaches the factory set "cut-out” pressure.

Safety Valve: If the pressure switch does not shut off the air compressor at its

"cut-out” pressure setting, the safety valve will protect against high pressure by

"popping out” at its factory set pressure (slightly higher than the pressure

switch "cut-out” setting).

Outlet Pressure Gauge: The outlet pressure gauge indicates the air pressure

available at the outlet side of the regulator. This pressure is controlled by the

regulator and is always less than or equal to the tank pressure.

Tank Pressure Gauge: The tank pressure gauge indicates the reserve air

pressure in the tank.

Regulator: Controls the air pressure shown on the outlet pressure gauge. Pull

the knob out and turn clockwise to increase pressure and counter-clockwise to

decrease pressure. When the desired pressure is reached push knob in to lock

in place.

Drain Valve: The drain valve is located at the

base of the air tank and is used to drain

condensation at the end of each use.

Cooling System (not shown): This compressor

contains an advanced design cooling system. At

the heart of this cooling system is an engineered

fan. It is perfectly normal for this fan to blow air

through the vent holes in large amounts. You know that the cooling system is

working when air is being expelled.

Know Your Air Compressor

READ THIS OWNER’S MANUAL AND SAFETY RULES BEFORE OPERATING

YOUR UNIT. Compare the illustrations with your unit to familiarize yourself with

the location of various controls and adjustments. Save this manual for future

reference.

Drain

Valve

Outlet

Pressure

Gauge

Safety Valve

Pressure

Switch

Regulator

Tank

Pressure Gauge

On/Auto/Off

Switch

Quick

Connect

Air Compressor Pump (not shown): Compresses air into the air tank.

Working air is not available until the compressor has raised the air tank pressure

above that required at the air outlet.

Check Valve: When the air compressor is

operating, the check valve is "open”, allowing

compressed air to enter the air tank. When the

air compressor reaches "cut-out” pressure, the

check valve "closes”, allowing air pressure to

remain inside the air tank.

How to Use Your Unit

How to Stop:

1. Set the On/Auto/Off lever to "OFF".

Before First Start-up

Break-in Procedure

Serious damage may result if the following break-in

instructions are not closely followed.

This procedure is required before the air compressor is put into service and

when the check valve or a complete compressor pump has been replaced.

1. Make sure the On/Auto/Off lever is in the "OFF" position.

NOTE: Pull coupler back until it clicks to

prevent air from escaping through the

quick connect.

2.

Plug the power cord into the correct

branch circuit receptacle.

(Refer to

Voltage and Circuit Protection

paragraph in the Installation section

of this manual.)

3. Open the drain valve fully

(counterclockwise) to permit air to

escape and prevent air pressure

build up in the air tank during the break-in period.

4. Move the On/Auto/Off lever to "ON/AUTO" position. The compressor will

start.

5. Run the compressor for 15 minutes. Make sure the drain valve is open and

there is minimal air pressure build-up in tank.

6. After 15 minutes, close the drain valve (clockwise). The air receiver will fill to

"cut-out" pressure and the motor will stop.

The compressor is now ready for use.

12 - ENG

D27856

Regulator

On/Auto/

Off Lever

Quick

Connect

Check Valve

13 - ENG

D27856

Before Each Start-Up:

1. Place On/Auto/Off lever to "OFF" and close air regulator.

2. Pull regulator knob out, turn counterclockwise until it stops. Push knob in

to lock in place.

3. Attach hose and accessories. NOTE: The hose or accessory will require a

quick connect plug if the air outlet is equipped with a quick connect

socket.

Too much air pressure causes a hazardous risk of bursting.

Check the manufacturer’s maximum pressure rating for air

tools and accessories. The regulator outlet pressure must never exceed

the maximum pressure rating.

How to Start:

1. Turn the On/Auto/Off lever to "AUTO" and allow tank pressure to build.

Motor will stop when tank pressure reaches "cut-out" pressure.

2. Pull the regulator knob out and turn clockwise to increase pressure. When

the desired pressure is reached push knob in to lock in place. The

compressor is ready for use.

NOTE: Always operate the air compressor in well-ventilated areas free of

gasoline or other combustible vapors. If the compressor is being used to

operate a sprayer DO NOT place near the spray area.

14 - ENG

D27856

Customer Responsibilities

Daily or

after

each

use

Before

each

use

●

Check Safety Valve

Drain Tank

NOTE: See "Operation" section for the location of controls.

Unit cycles automatically when power is on. When

performing maintenance, you may be exposed to voltage

sources, compressed air, or moving parts. Personal injuries can occur.

Before performing any maintenance or repair, disconnect power source

from the compressor and bleed off all air pressure.

To Check Safety Valve

If the safety valve does not work properly, over-

pressurization may occur, causing air tank rupture or an

explosion.

1. Before starting compressor, pull the ring on the safety valve to make sure

that the safety valve operates freely. If the valve is stuck or does not

operate smoothly, it must be replaced with the same type of valve.

To Drain Tank

1. Set the On/Auto/Off lever to "OFF".

2. Pull the regulator knob out and turn counterclockwise to set the outlet

pressure to zero.

3. Remove the air tool or accessory.

4. Pull ring on safety valve allowing air to bleed from the tank until tank

pressure is approximately 20 psi. Release safety valve ring.

5. Drain water from air tank by opening drain valve (counter-clockwise) on

bottom of tank.

Water will condense in the air tank. If not drained, water

will corrode and weaken the air tank causing a risk of air

tank rupture.

6. After the water has been drained, close the drain valve (clockwise). The air

compressor can now be stored.

NOTE: If drain valve is plugged, release all air pressure. The valve can then be

removed, cleaned, the reinstalled.

MAINTENANCE

15 - ENG

D27856

Unit cycles automatically when power is on. When doing

Maintenance, you may be exposed to voltage sources,

compressed air or moving parts. Personal injuries can occur. Before

performing any Maintenance or repair, unplug the compressor and bleed

off all air pressure.

ALL MAINTENANCE AND REPAIR OPERATIONS NOT LISTED MUST BE

PERFORMED BY A TRAINED SERVICE TECHNICIAN.

Before servicing:

Unplug or disconnect electrical supply to the air compressor.

Bleed tank of pressure

Allow the air compressor to cool

To Replace or Clean Check Valve

1. Release all air pressure from air tank. See “To Drain Tank" in the

Maintenance section.

2. Unplug unit.

3. Remove the hose by removing the

hose clamp.

NOTE: The hose clamp is not reusable.

You must purchase a new hose clamp,

see the Parts List Manual or purchase a

standard hose clamp at a local hardware

store.

4. Unscrew the check valve (turn

counter-clockwise) using a socket wrench.

5. Make sure the valve disc moves freely inside the check valve and the

spring holds the disc in the upper, closed position. The check valve may be

cleaned with a solvent, such as paint and varnish remover.

6. Apply sealant to the check valve threads. Reinstall the check valve (turn

clockwise).

7. Replace hose and new hose clamp.

8. Perform the Break-in Procedure. See "Break-in Procedure" in the

Operation section.

Check

Valve

Hose Clamp

SERVICE AND ADJUSTMENTS

To Replace Regulator

1. Release all air pressure from air tank. See "To Drain Tank" in the

Maintenance section.

2. Unplug unit.

3. Using an adjustable wrench remove the

outlet pressure gauge and quick connect

from the regulator.

4. Remove the regulator.

5. Apply pipe sealant tape to the nipple on the

standpipe.

6. Assemble the regulator and orient as shown.

NOTE: Arrow indicates flow of air. Make sure it is

pointing in the direction of air flow.

7. Reapply pipe sealant to outlet pressure gauge

and quick connect.

8. Reassemble outlet pressure gauge and quick

connect. Orient outlet pressure gauge to read

correctly. Tighten connect with wrench.

Nipple

Outlet

Pressure

Gauge

Quick

Connect

Regulator

Arrow

16 - ENG

D27856

17 - ENG

D27856

Before you store the air compressor, make sure you do the following:

1. Review the "Maintenance" section on the preceding pages and perform

scheduled maintenance as necessary.

2. Set the On/Auto/Off lever to “OFF”.

3. Turn the regulator counterclockwise and set the outlet pressure to zero.

4. Remove the air tool or accessory.

5. Pull ring on safety valve allowing air to bleed from the tank until tank

pressure is approximately 20 psi. Release safety valve ring.

6. Drain water from air tank by opening drain valve on bottom of tank.

Water will condense in the air tank. If not drained, water

will corrode and weaken the air tank causing a risk of air

tank rupture.

7. After the water has been drained, close the drain or drain valve.

NOTE: If drain valve is plugged, release all air pressure. The valve can then be

removed, cleaned, then reinstalled.

8. Protect the electrical cord and air hose from damage (such as being

stepped on or run over). Wind them loosely around the compressor

handle. (If so equipped)

Store the air compressor in a clean and dry location.

STORAGE

LIMITED WARRANTY

Porter-Cable Corporation

Jackson, TN USA

1-888-559-8550

PORTER-CABLE CORPORATION warrants to the original purchaser that all products covered under this

warranty are free from defects in material and workmanship. Products covered under this warranty include air

compressors, air tools, service parts, pressure washers, and generators, which have the following warranty

periods:

3 YEARS - Limited warranty on 2-stage oil-free air compressor pumps that operate at 1725 RPM.

2 YEARS - Limited warranty on oil-lubricated air compressor pumps.

1 YEAR - Limited warranty on all other air compressor components.

2 YEARS - Limited warranty on electric generator alternators.

1 YEAR - Limited warranty on other generator components.

2 YEARS - Limited warranty on pneumatic air tools as described in Porter-Cable general catalog.

1 YEAR - Limited warranty on pressure washers used in consumer applications (i.e. personal residential

household usage only).

90 DAY - Pressure washers used for commercial applications (income producing) and service parts.

1 YEAR - Limited warranty on all accessories.

Porter-Cable will repair or replace, at Porter-Cable's option, products or components which have failed

within the warranty period.

Service will be scheduled according to the normal work flow and business

hours at the service center location, and the availability of replacement parts.

All decisions of Porter-

Cable Corporation with regard to this limited warranty shall be final.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

RESPONSIBILITY OF ORIGINAL PURCHASER (initial User):

• To process a warranty claim on this product, DO NOT return it to the retailer. The product must be

evaluated by an Porter-Cable Authorized Warranty Service Center. For the location of the nearest Porter-

Cable Authorized Warranty Service Center call 1-888-559-8550, 24 hours a day, 7 days a week.

• Retain original cash register sales receipt as proof of purchase for warranty work.

• Use reasonable care in the operation and maintenance of the product as described in the Owners

Manual(s).

• Deliver or ship the product to the nearest Porter-Cable Authorized Warranty Service Center. Freight costs,

if any, must be paid by the purchaser.

• Air compressors with 60 and 80 gallon tanks will be inspected at the site of installation. Contact the nearest

Porter-Cable Authorized Warranty Service Center that provides on-site service calls, for service call

arrangements.

• If the purchaser does not receive satisfactory results from the Porter-Cable Authorized Warranty Service

Center, the purchaser should contact Porter-Cable.

THIS WARRANTY DOES NOT COVER:

• Merchandise sold as reconditioned, used as rental equipment, and floor or display models.

• Merchandise that has become damaged or inoperative because of ordinary wear, misuse*, cold, heat, rain,

excessive humidity, freeze damage, use of improper chemicals, negligence, accident, failure to operate the

product in accordance with the instructions provided in the Owners Manual(s) supplied with the product,

improper maintenance, the use of accessories or attachments not recommended by Porter-Cable, or

unauthorized repair or alterations.

* An air compressor that pumps air more than 50% during a one hour period is considered misuse

because the air compressor is undersized for the required air demand.

• Repair and transportation costs of merchandise determined not to be defective.

• Costs associated with assembly, required oil, adjustments or other installation and start-up costs.

• Expendable parts or accessories supplied with the product which are expected to become inoperative or

unuseable after a reasonable period of use, including but not limited to sanding disks or pads, saw and

shear blades, grinding stones, springs, chisels, nozzles, o-rings, air jets, washers and similar accessories.

• Merchandise sold by Porter-Cable which has been manufactured by and identified as the product of

another company, such as gasoline engines. The product manufacturer's warranty, if any, will apply.

• ANY INCIDENTAL, INDIRECT OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY

RESULT FROM ANY DEFECT, FAILURE OR MALFUNCTION OF THE PRODUCT IS NOT COVERED BY

THIS WARRANTY. Some states do not allow the exclusion or limitation of incidental or consequential

damages, so the above limitation or exclusion may not apply to you.

• IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may

not apply to you.

Compresores

de tipo plano

Manual de

Instrucciones

La placa de Modelo y de Número de Serie está

localizada en la caja principal de la herramienta. Anote

estos números en las líneas de abajo y guárdelos para

su referencia en el futuro.

Número de modelo _______________________________

Tipo ____________________________________________

Número de serie _________________________________

IMPORTANTE

Asegúrese de que la persona que va a usar

esta herramienta lea cuidadosamente y

comprenda estas instrucciones antes de

empezar a operarla.

Número de parte D27856-0210-0

ENGLISH: PAGE 1

FRANÇAISE : PAGE 37

Para obtener más información

sobre Porter-Cable,

visite nuestro sitio web en:

http://www.porter-cable.com

MODELO

CPFAC2600P

PROFESSIONAL POWER TOOLS

20 - SP

D27856

DEFINICIONES DE NORMAS DE SEGURIDAD

Indica una situación de

inminente riesgo, la

cual, si no es evitada, causará la

muerte o lesiones serias.

Indica una

situación

potencialmente riesgosa, que si no es

evitada, podría resultar en la muerte o

lesiones serias.

Indica una situación

potencialmente

peligrosa, la cual, si no es evitada, podría

resultar en lesiones menores o

moderadas.

Usado sin el

símbolo de

seguridad de alerta indica una situación

potencialmente riesgosa la que, si no es

evitada, podría causar daños en la

propiedad.a

SEGURIDAD Y PREVENCIÓN DE PROBLEMAS DEL EQUIPO: Para ayudar al

reconocimiento de esta información, hemos utilizado los símbolos mostrados abajo.

Sírvase leer el manual y prestar atención a dichas secciones.

IMPORTANTES INSTRUCCIONES DE SEGURIDAD

Algunos tipos de aserrín creados por máquinas eléctricas de lijado, aserrado,

amolado, perforado u otras actividades de la construcción, contienen materiales

químicos conocidos (en el Estado de California) como causantes de cáncer, defectos de nacimiento u otros

daños del aparato reproductivo. Algunos ejemplos de dichos productos químicos son:

●

El plomo contenido en algunas pinturas con base de plomo

●

Sílice cristalizado proveniente de los ladrillos, el cemento y otros productos de albañilería

●

Arsénico y cromo provenientes del tratamiento químico dado a la madera

Su riesgo a dichas exposiciones variará dependiendo de la frecuencia con la que usted realice

diferentes tipos de trabajo. Para reducir su exposición a la acción de dichos agentes químicos:

trabaje en zonas bien ventiladas, y hágalo con equipo de seguridad aprobado,

use siempre protección

facial o respirador MSHA / NIOSH aprobados cuando deba utilizar dichas herramientas.

Al utilizar herramientas neumáticas también deben tomarse precauciones básicas de seguridad, a fin

de reducir la posibilidad de riesgo de lesiones personales.

LEA Y SIGA TODAS LAS INSTRUCCIONES

Esta herramienta ha sido diseñada para ciertos usos. Porter-Cable recomienda enfáticamente que la

misma NO sea modificada y/o utilizada para cualquier otra aplicación más que para la que fuera

diseñada. En caso de tener dudas relacionadas con su aplicación, NO utilice la herramienta hasta

haber escrito a Porter-Cable y recibir nuestra respuesta aconsejándolo.

Gerente de Servicio Técnico

Porter-Cable Corporation

4825 Highway 45 North

P.O. Box 2468

Jackson, TN 38302-2468

La page est en cours de chargement...

Porter-Cable Air Compressor CPFAC2600P Manuel utilisateur

Ce manuel convient également à

Porter-Cable Air Compressor CPFAC2600P Manuel utilisateur

dans d''autres langues