Modern Forms PD-30156 Luzerne Mode d'emploi
- Taper
- Mode d'emploi
1
INSTALLATION INSTRUCTIONS
301 - LED Pendant
PD-30156
HARDWARE
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
AA A A A
Oct. 2022
Wire Connector
Qty: 2pcs+1 Extra
Wire Connector
Qty:2pcs+1 Extra
Cover
Qty: 1pcs
Fixed Screw
Qty: 2 Extra
Mounting Screw
Qty:1 Extra
• Read all instructions before installing.
• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
•
• Retain installation instructions for future maintenance reference.
: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product by Modern
Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any
parts are damaged or missing.
: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
• Lisez toutes les instructions avant l’installation.
• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou accessoires non conçus
pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la
garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
INSTALLATION INSTRUCTIONS
PD-30156
301 – LED Pendant
2
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
Fig.1
Oct. 2022
Junction Box Screw
Wire Connectors
Wire Connectors
Driver
Junction Box
Canopy
Mounting Screw
2x6"Rods
6x12"Rods
Extra Long Replacement Glass
(RPL-GLA-30156-04)
Long Replacement Glass
(RPL-GLA-30156-03)
Medium Replacement Glass
(RPL-GLA-30156-02)
Short Replacement Glass
(RPL-GLA-30156-01)
Cover
Fixed Plate
Fixed Screw
Magnet
A
A
A
A
A
Mounting plate
Quick Connect Fast Male Terminal
Quick Connect Fast Female Terminal
Frosted Acrylic Lampshade
Extrusion Body
INSTALLATION INSTRUCTIONS
PD-30156
301 – LED Pendant
3
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
PREPARATION
INSTALLATION
1. Shut off the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
3. Remove the mounting screw (C) from the xture, then remove the mounting plate.
5. From one side of the body only, remove the xed screw (E), then remove the xed plate.
MOUNTING THE FIXTURE (Fig. 1)
Oct. 2022
CONNECTING THE WIRES (Fig. 2 / Fig. 3)
10. Secure the xture to the mounting plate using the mounting screw (C).
11. For slope ceiling application, rotate swivel at the top of the stem to ensure
luminaire is aiming down (Fig. 5).
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring Fig. 3 Driver Wiring
White - Neutral
Black - Hot
Red +
Black -
Red +
Black -
Driver
Input
Output
Canopy
Fig. 4 Mounting plate
4 3/8”
1 3/8”
4 3/8”
1 3/4”
6. Insert the frosted acrylic shade into the center of the body, and connect the male and female terminal, as shown in Fig.1, Insert the reeded
glass according to the conguration in Fig.1. Align the mounting holes in the xed plate with the mounting holes in the body; align the rings in
4. Secure the mounting plate to the junction box using standard junction box screws that comes with the junction box .
Note (i) using any other non-original-manufacturer provided junction box screw may result in safety issue;
(ii) The side of the mounting plate marked “GND” must face out.
Fig. 5
are secured. Then tuck them inside the canopy.
9. Connect the driver’s input wires to junction box wires as shown in Fig. 2, making sure that all wire connectors (A) are secured. If your outlet box
has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly to the
mounting plate using the GND screw provided. After wires are connected, tuck them carefully inside the junction box.
COMPLETING THE INSTALLATION
Turn to down
8. Connect the driver’s output wires to xture wire as shown in Fig.3, red to the red,and black to the black, make sure that wire connectors(B)
the xed plate with the reeded glass. Secure the xed plate to the body using xed screw (E), top off by inserting the cover (D) over the xed plate.
7. Choose the number of the rods suitable for your application.Thread the xture wire through the rods, swivel and canopy. Connect the xture,
rods and swivel. Make sure all are tightened. .
-
1
-
2
-
3
Modern Forms PD-30156 Luzerne Mode d'emploi
- Taper
- Mode d'emploi
dans d''autres langues
Documents connexes
-
Modern Forms WS-30118 Luzerne Mode d'emploi
-
-
-
-
-
-
-
-
-