Mopar K6862043 Installation Instructions Manual

K6862043

3/11/14

1

CALL OUT DESCRIPTION QUANTITY

A1

Radio Harness

B1

TOOLS REQUIRED

Grease Pencil

C1

Handle with Camera Provisions

D

E

1

Trim Stick

Camera/Lock Jumper Harness

Tailgate Wire Harness

Cable Tie

Phillips Screwdriver

Metric Socket Set

Crimping ToolWire Cutters RTV Sealant 82300234

Backup Camera

Splice Clip

Shrink Tube

F

G

3

Camera Body Harness

H60

www.mopar.com

AC

E

D

H

F

G

B

K6862043

3/11/14

1. Loosen one (1) 10mm bolt and disconnect

negative battery cable

2

NOTE: Vehicle with tailgate liner shown.

The tailgate liner and tailgate cover are

removed and installed as one piece.

2. Open the tailgate.

3. If equipped with tailgate liner (2), remove screws (1)

and remove the tailgate cover.

4. Using a grease pencil or equivalent, mark the

location of the actuator rods (2) at the latch control.

5. Disconnect the actuator rods from the latch control.

www.mopar.com

K6862043

3/11/14

3

6. Remove the two nuts (3) that secure the release

handle (1) and the latch control (2) to the tailgate.

7. Remove the latch control (2) and the release handle

(1) from the tailgate.

11. Position the new handle (C) and the latch control (2)

to the tailgate.

12. Install the two nuts (3) that secure the release handle

and latch control to the tailgate. Tighten the nuts

to 6 N·m (53 in. lbs.).

8. Remove the screws (1) securing the lock cylinder (2)

to the old handle.

9. Transfer the lock cylinder to the new handle (C)

with camera.

10. Install retaining screws and tighten securely.

www.mopar.com

C

K6862043

3/11/14

NOTE: If equipped with a power lock actuator, remove

and discard the lock actuator harness.

13. Connect the supplied harness (E) to the camera and

connect the supplied tailgate harness (D) to harness (E).

NOTE: Tape back the lock actuator connector if

vehicle is not equipped with a lock actuator.

14. Connect the lock actuator connector (1) (if equipped).

15. Route tailgate jumper harness (D) through the

tailgate as shown to the tailgate closeout panel (2).

4

www.mopar.com

D

E

K6862043

3/11/14

5

16. Install the actuator rods (2) to the latch control using

the reference marks made during the removal

procedure.

17. Install the tailgate cover and liner (if equipped).

NOTE: If the vehicle is equipped with the tailgate lock

actuator, you must remove and transfer the two

wires from the existing body side tailgate

connector to the supplied body harness (A)

connector. See graphic for more information.

18. If equipped with the tailgate lock actuator, remove the

wires (1, 2) from the existing tailgate connector (3),

then discard the existing tailgate connector.

19. Remove the terminal plugs from cavities 7 and 8 in

the supplied body harness connector (A).

20. Transfer the P237 DG/TN wire removed from cavity

7 of the original connector and transfer into cavity 7

of the supplied harness connector.

21. Transfer the P235 LG/TN wire removed from cavity 8

of the original connector and transfer into cavity 8 of

the supplied harness connector.

www.mopar.com

K6862043

3/11/14

6

NOTE: When routing the body harness, make sure

the harness cannot contact any moving parts

or hot exhaust.

22. Route supplied body harness (A) from the back of

the vehicle to the front as shown, following the

existing harness on the driver side. Tie straps must

be used every 150mm to secure harness (A) to

the existing vehicle harness.

23. Remove the ground bolt (2) located on the left

fender next to the Power Distribution Center (PDC).

24. Connect the black wire in the supplied body harness

(A) to the ground location on the fender.

25. Install the ground nut (2). Tighten the ground bolt to

9 N·m (80 in. lbs.).

26. Release the PDC retaining clips (1) and remove the

PDC from the mounting bracket.

www.mopar.com

A

2

1

K6862043

3/11/14

7

27. Rotate the PDC to gain access to the underside of

the PDC.

28. Locate circuit F923 (PK/YL) at cavity 13 (1) on the

underside of the PDC.

29. Splice the red wire from the supplied body harness

(C) to the PK/YL (F923) wire at cavity 13 of the PDC

(Splice and solder new wire to the original wire

using the soldering procedure in steps 30 thru 33).

30. Place the strands of the wires overlapping each

other inside of the splice clip (1).

31. Using Mopar® crimping tool (1) or equivalent, crimp

the splice clip and wires together.

www.mopar.com

K6862043

3/11/14

8

32. Solder (3) the connection (2) together using rosin

core solder (1).

33. Center the heat shrink tubing (2) over the solder joint

and heat using a heat gun. Heat the joint until the

tubing is tightly sealed and sealant (1) comes out of

both ends of the tubing.

34. Install the PDC to its original mounting location by

pressing it back into place.

35. Route the remaining supplied body harness (A) to

the body grommet on driver side bulkhead.

36. Cut the end off the dash panel grommet nipple (1)

hanging off the bottom side of the body harness

near the brake booster.

37. Route the backup camera harness through the dash

panel grommet nipple.

38. Apply MoparT RTV 82300234 around the grommet

nipple.

www.mopar.com

K6862043

3/11/14

9

39. Continue to route the supplied body harness (A) to

the driver kick panel area.

40. Insert wires into supplied connector (taped to

harness in polybag) as listed below:

 Cavity A  GRY/BLU

 Cavity B  YEL

 Cavity C - GRN

 Cavity D  GRY/ORG

 Cavity E  Bare

 Cavity F - BLU

41. Release and remove connector C5 (1) from the

Body Control Module (BCM).

42. Remove the housing (2) to gain access to the

terminal blocks (1).

www.mopar.com

K6862043

3/11/14

10

NOTE: Connector C5 front view is shown.

43. Insert the purple wire from supplied harness (A)

into connector C5 cavity 45. If the cavity is already

populated, cut the terminal off the purple wire and

splice the purple wire to the ORG/DB wire in cavity 45

(Splice and solder new wire to the original wire using

the soldering procedure in steps 30 thru 33).

NOTE: Yellow wire is not used. Tape back onto harness.

44. Assemble connector C5 and insert back into BCM.

NOTE: Be sure to keep all fasteners for later

reinstallation.

45. Remove the storage tray cover (1) from the top center

area of the dashboard. Remove fasteners (2) from the

storage tray (3). Remove the tray.

46. Remove the storage tray (1) from the front of the

center console.

2

1

3

www.mopar.com

K6862043

3/11/14

11

49. Remove fastener (1) from the storage cubby on the

right side of the center dash trim panel. Carefully

disengage all retainer clips and pry off the trim panel (2).

47. Remove the edge trim (1) from the center console

cover panel.

48. Remove fasteners (1) at the front edge of the center

console cover panel (2). Remove the cover panel.

1

www.mopar.com

2

1

2

1

K6862043

3/11/14

12

50. Disconnect all plugs from the back of panel (1).

Remove the panel from the vehicle.

51. Remove fasteners (2) from the radio assembly.

52. Remove radio assembly (1) from dash. Unlock the

the 52-way connector (2) at the back of the radio and

disconnect.

53. Route the radio harness (B) under the dashboard and

up to the center stack. Secure harness with cable

ties (H).

NOTE: Cable ties should be installed no farther

than 100mm apart.

www.mopar.com

2

1

2

1

H

B

K6862043

3/11/14

13

55. If necessary, depopulate the three existing wires

indicated from the connector and tape back onto

the harness. Insert the new wires from the

camera harness as follows:

 Cavity 31  GRY/BLU

 Cavity 32  GRY/ORA

 Cavity 33 - Bare

56. Check all wiring and trim all cable ties.

57. Reconnect the battery.

58. Reverse steps 45 through 52, 26, and 3 to reinstall all vehicle components.

59. Follow the Vehicle Configuration Instructions on the next page.

54. Feed the three-prong end of radio harness (B) up into

the center stack and out through the radio opening.

NOTE: Use Miller 6680 Depopulate Tool to remove wires.

B

www.mopar.com

B

PIN 31

PIN 32

PIN 33

K6862043

3/11/14

14

RAM CAMERA VEHICLE CONFIGURATION

Vehicle VIN must be updated with the sales code of the added accessory in order to enable system

functionality. Using the DealerCONNECT website and the scan tool, complete the procedure below:

1. Log on to https://dealerconnect.chrysler.com

2. In the service tab, inside the Warranty Administration box, locate Vehicle Option Updates.

Enter the vehicle VIN and add the sales code XAC (Park View Rear BackUp Camera) as a

Dealer Installed Option.

3. Confirm that the new sales code has been successfully added to the VIN. With the scan tool

connected to both the internet (via Ethernet port or wireless connection) and the vehicle, follow

the steps below:

4. Using the scan tool select the VEHICLE PREPARATION and then select

RESTORE VEHICLE CONFIGURATION.

5. Follow the step by step instructions on the scan tool to complete the Park View Rear BackUp

Camera vehicle configuration.

6. When the Park View Rear BackUp Camera Vehicle Configuration is complete, go to the

Validation Process to verify that the vehicle has been updated.

VALIDATION PROCESS

From the Initial Start Up screen on the scan tool follow the steps below:

1. Using the scan tool follow the menu to ECU VIEW, select TIPMCGW CENTRAL GATEWAY,

MORE OPTIONS, ECU DETAILS and then CONFIG INFO

2. Verify REAR CAMERA SET is present.

3. Clear any DTCs that may have been set. Some modules may have to be initialized after the

reconfiguration.

www.mopar.com

K6862043

3/11/14

1

A1

Harnais de radio

B1

Crayon gras

C1

Poignée avec dispositions pour caméra

D

E

1

Caméra et faisceau de cavalier de verrouillage

Faisceau de câblage du hayon

Attache-câbles

Pince à sertirRTV mastic 82300234

CAMÉRA DAIDE AU RECUL

Trousse de jonction

Tube thermorétrécissable

F

G

3

Caméra et faisceau de carrosserie

H60

RÉFÉRENCE DESCRIPTION QUANTITÉ

OUTILS REQUIS

Ensemble de douilles métriques Tournevis Phillips Outil pour garnitures

Coupe-fil

www.mopar.com

AC

E

D

H

F

G

B

K6862043

3/11/14

2

NOTA : Véhicule avec garniture de hayon illustré.

La garniture et le couvercle du hayon sont retirés

et installés en un bloc.

2. Ouvrez le hayon.

3. Si le véhicule est équipé de la garniture de hayon (2),

retirez les vis (1) et enlever le couvercle de hayon.

4. À laide dun crayon gras ou dun outil équivalent,

marquez lemplacement des tiges dactionneur (2)

au niveau de la commande de loquet.

5. Débranchez les tiges dactionneur de la commande

de loquet.

1. Déconnectez le câble négatif de laccumulateur en

desserrant un (1) boulon de 10 mm.

www.mopar.com

K6862043

3/11/14

3

6. Retirez les deux écrous (3) qui fixent la poignée de

déverrouillage (1) et la commande de loquet (2)

au hayon.

7. Retirez la commande de loquet (2) et la poignée de

déverrouillage (1) du hayon.

11. Placez la nouvelle poignée (C) et la commande

de loquet (2) sur le hayon.

12. Installez les deux écrous (3) qui fixent la poignée de

déverrouillage et la commande de loquet au hayon.

Serrez les écrous au couple de 6 N.m (53 lb-po).

8. Retirez les vis (1) qui fixent le barillet de serrure (2)

à la vieille poignée.

9. Transférez le barillet de serrure à la nouvelle poignée

avec la caméra (C).

10. Installez les vis de fixation et serrez-les solidement.

www.mopar.com

C

K6862043

3/11/14

NOTA : Si le véhicule est équipé dun actionneur de

serrure électrique, retirez le faisceau dactionneur de

serrure et mettez-le au rebut.

13. Brancher le faisceau (E) à la caméra. Connectez

harnais (D) à exploiter (E).

NOTA : Placez le connecteur dactionneur de serrure

vers larrière à laide de ruban adhésif si le véhicule

nest pas équipé dun actionneur de serrure.

14. Branchez le connecteur dactionneur de serrure (1)

(selon léquipement).

15. Acheminez le faisceau de cavalier du hayon (D) dans

le hayon, comme illustré, vers le panneau de fermeture

du hayon (2).

4

www.mopar.com

D

E

K6862043

3/11/14

5

16. Installez les tiges dactionneur (2) sur la commande

de loquet au moyen des repères de référence faits

pendant la procédure de dépose.

17. Installez le couvercle et la garniture de hayon

(selon léquipement).

NOTA : Si le véhicule est équipé de lactionneur de

serrure de hayon, vous devez retirer les deux fils du

connecteur de hayon du côté carrosserie existant

et les transférer au connecteur de faisceau de

carrosserie fourni (A). Consultez le graphique pour

obtenir de plus amples renseignements.

18. Si le véhicule est équipé de lactionneur de serrure

de hayon, déposez les câbles (1, 2) du connecteur

de hayon actuel (3), puis mettez au rebut le

connecteur de hayon actuel.

19. Retirez les fiches de borne des cavités 7 et 8 dans

le connecteur du faisceau de carrosserie fourni (A).

20. Transférez le fil du circuit P237 (DG/TN) qui a été retiré

de la cavité 7 du connecteur dorigine et transférez-le

à la cavité 7 du connecteur de faisceau fourni.

21. Transférez le fil du circuit P235 (LG/TN) qui a été retiré

de la cavité 8 du connecteur dorigine et transférez-le

à la cavité 8 du connecteur de faisceau fourni.

www.mopar.com

K6862043

3/11/14

6

NOTA : Lors de lacheminement du faisceau de

carrosserie, assurez-vous que le faisceau ne peut pas

entrer en contact avec les pièces amovibles ou le

système déchappement chaud.

22. Acheminez le faisceau de carrosserie fourni (A) à partir

de larrière du véhicule jusquà lavant, comme illustré, en

suivant le faisceau existant sur le côté conducteur.

REMARQUE : Les attache-câbles ne devraient pas

être distancés de plus de 150 mm.

23. Déposez le boulon de masse (2) situé sur laile gauche

à côté de la centrale de servitudes (PDC).

24. Connectez le fil noir dans le faisceau de carrosserie

fourni (A) à la masse située sur laile.

25. Posez le boulon de masse (2). Serrez le boulon de

masse au couple de 9 N.m (80 lb-po).

26. Libérez les agrafes de fixation de la centrale de

servitudes (1) et retirez la centrale du support

de fixation.

www.mopar.com

A

2

1

La page est en cours de chargement...

Mopar K6862043 Installation Instructions Manual

Mopar K6862043 Installation Instructions Manual

dans d''autres langues

Documents connexes

Autres documents