Grandstream GRP260X RingCentral IP Phone Guide d'installation

Catégorie
Téléphones IP
Taper
Guide d'installation
Grandstream Networks, Inc.
Configuration Guide:
GRP260X For RingCentral MVP
2
Table of Contents
!
Revision History 3!
GRP260X and RingCentral Software Versions 3!
Overview 4!
Features Supported by GRP260X Series 4!
Configuration RingCentral Web Portal 5!
Add a RingCentral MVP User 5!
Add a GRP260X Device 5!
Get SIP Settings for Manual Provisioning 5!
Manual Provison GRP260X via Web Interface 6!
Unlock and Reset GRP260X 7!
Perform a Factory Reset via LCD 7!
Log in GRP260X Web UI 7!
Firmware Upgrade 11!
3
Revision History
Version
Date
Author
Change
1.0
02/17/2023
Cindy Li
Created document
GRP260X and RingCentral Software Versions
Equipment
Software Version
Grandstream (Device
Under Test)
GRP260X
1.0.3.70 and any maintenance
releases
RingCentral
MVP
4
Overview
This document outlines the configuration best practices for Grandstream GRP260X as a BYOD generic SIP
phone on RingCentral MVP platform. tekVizion has validated SIP interoperbility of Grandstream GRP260X
with RingCentral. Customers are advised to check Grandstream website for GRP260X documentation. Here is
the link to GRP260X Administration Guide.
Features Supported by GRP260X Series
Below are telephony features on Grandstream GRP260X that have been validated on RingCentral MVP.
Registration and Provision
Make and Receive Calls
Inbound and Outbound Call Identification
Call Hold and Retrieval
DND
Call Waiting
Call Forward Always
Call Forward No Answer
Call Forward Busy
Blind/Cold Transfer
Consultative/Warm Transfer
3-party Conference
Voicemail
Call History
Company Directory
Speed dial
Call Flip
Call Return
Caller ID Block
Calling Ring Groups
Directed Call Pickup
Call Recording
Auto Receptionist IVR
Call Park/Retrieve
Secure Voice (TLS and SRTP)
5
Configuration RingCentral Web Portal
This section describes the configuration needed on RingCentral MVP portal for Granstream GRP260X manual
provision. A valid RingCentral administrator account is required to accomplish these tasks.
Add a RingCentral MVP User
RingCentral MVP users are created in order to log in RingCentral clients on desktop or mobile, it can also be
assigned to SIP devices. Please follow the instructions of RingCentral document below to add a new user with
extension:
Add MVP User with Extensions in Admin Portal
Add a GRP260X Device
Once a user and extension has been added in the system, please follow the instructions below to add your
GRP260X phone.
Add Your GRP260X Device
Get SIP Settings for Manual Provisioning
Get SIP Settings for Manual Configuration
1. Go to the Admin Portal and sign in.
2. Go to Phone System
à
Phones & Devices
à
User Phones
3. Select Existing Phone
If you don’t have this under your User Phones list, you can add one by clicking Add Device
4. Click Set Up and Provision
5. Click Set up manually using SIP
Select the Yes The device must support Transport Protocol version TLS 1.2 radio button.
Note: It is recommended to use TLS 1.2 for enhanced network security.
From Outbound Proxy drop down list, select a proxy according to the location of your device (ex:
sip10.ringcentral.com:5096)
6
Figure 1 : SIP Settings in RingCentral Portal
Note on Paging: Currently GRP260X is not supported by RingCentral to receive paging as a user phone. In
order for GRP260X to receive paging, users need to create a paging device on RingCentral admin portal under
Phone System à Phones & Devices à Paging Devices. Then use the provided SIP information to register
GRP260x.
Manual Provison GRP260X via Web Interface
This section describes manual configuration steps on Grandstream GRP260X using SIP settings populated on
RingCentral portal (shown in Figure 1).
By default, GRP260X has DHCP enabled. If the router that the phone is connected to does not support DHCP,
you can configure static IP manually. Please find GRP260X’s IP address by navigating on phone’s LCD using
keypad: Menu à Status à Network Status à Ethernet.
7
Unlock and Reset GRP260X
1. Please ensure that your GRP260X device is unlocked: If your phone / device was purchased from a
previous service provider, please ensure that it is unlocked before it can be registered / provisioned. If you
need help, please contact your previous service provider.
2. Factory reset the phone: By doing a factory reset, any previous settings / configurations that could
possibly conflict with the manual provisioning settings will be removed.
Perform a Factory Reset via LCD
1. Press the round MENU button to bring up the keypad configuration menu.
2. Navigate to Menu option 8 - Factory Reset.
3. Press the round MENU button.
4. A warning window will pop out to make sure a reset is requested and confirmed.
5. Press the “Yes” Softkey to confirm and the phone will reboot, or “No” Softkey to cancel the Reset.
Log in GRP260X Web UI
Once the GRP260X boots up, enter the phone’s IP address in the browser’s address bar (https://ip-address)
and input phone’s username and password displayed in the phone’s LCD screen and click Login.
Figure 2 : Login details
Phone prompts to update with New Password. Enter a New Password and Confirm Password. Click Modify.
8
Figure 3 : Login details - (Cont.)
Navigate to Accounts à Accounts à Account 1
Under Account 1 à General Settings, ensure below parameters are set.
1. Account Active: Check
2. Account Name: Enter Account Name of your choice. Here, Grandstream Two is used
3. SIP Server: sip.ringcentral.com:5060
4. Outbound Proxy: sip10.ringcentral.com:5096
5. SIP User ID: RingCentral Phone Number
6. SIP Authentication ID: Provide the SIP Authentication ID
7. SIP Authentication Password: Provide the SIP Authentication Password
8. NAT Traversal: No
9. Click Save and Apply
9
Figure 4 : General Settings
Figure 5 : General Settings (Cont.)
Under Account 1 à SIP Settings, ensure below parameters are set.
1. SIP Registration: Checked
2. SIP Transport: TLS/TCP
3. SIP URI Scheme When Using TLS: sip
4. Click Save and Apply
10
Figure 6 : SIP Settings (Cont.)
Under Account 1 à Codec Settings, ensure below parameters are set.
1. SRTP Mode: Enabled and Forced
2. SRTP Key Length: AES 128&256 bit
3. Click Save and Apply
Figure 7 : Codec Settings
Under Account 1 à Feature Codes, ensure below parameters are set.
1. Enable Local Call Features: Unchecked
2. Click Save and Apply
11
Figure 8 : Feature Codes
After the above configuration steps, navigate to Status -> Account Status to check the account registration status.
Figure 9 : Account Status
Firmware Upgrade
This section describes the GRP260X firmware upgrade process. The firmware version passed
RingCentral/tekVizion certification is 1.0.3.70. But any maintenance releases should work with RingCentral
MVP. Users are recommended to upgrade to the latest firmware. Grandstream firmware is available for
download from the company website at https://www.grandstream.com/support/firmware.
From the phone’s home page, navigate to: Maintenance à Upgrade and Provisioning
Select Firmware tab
Under Upgrade via Manually Upload: Upload Firmware File to Update - Click Upload to upload the
firmware file from the PC
Selected firmware file will be upgraded to the phone
From Phone’s LCD screen, Select Yes to Reboot and switch to (1.0.3.70) (Phone may restart to apply
the changes)
12
Figure 10 : Firmware Upgrade
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Grandstream GRP260X RingCentral IP Phone Guide d'installation

Catégorie
Téléphones IP
Taper
Guide d'installation