Chief LCM2X1U Guide d'installation

LCM2X1U
Chief
Marque
Chief
Modèle
LCM2X1U
Catégorie
Mur
Taper
Guide d'installation

Ce manuel convient également à

INSTALLATION INSTRUCTIONS
LCM2X1U
LCM2X1UP
Ceiling-Mounted Menu Boards
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
LCM2X1U / LCM2X1UP
LCM2X1U / LCM2X1UP Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located within the mounting system of the
LCM2X1U/LCM2X1UP models does not exceed maximum
weights listed in Table 1.
Table 1: Weight Capacity
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
NOTE: The LCM2X1U and
LCM2X1UP ceiling mounted menu
boards are intended to be used with the UL Listed CPA
Ceiling Plates (not included): CPA330, CPA365,
CPA395 and UL Listed extension brackets FCAX08,
FCAX14 and FCAX20.
The following UL Listed Chief ceiling plates WITHOUT
swaged collars (not included) may also be used:
CMA330, CMA345, CMA395.
--SAVE THESE INSTRUCTIONS--
MODEL Max Weight
Allowed for EACH
Display
Max Weight
Capacity of
Mounting System
LCM2X1U 125 lbs
(56.7 kg) 250 lbs
(113.4 kg)
LCM2X1UP 125 lbs
(56.7 kg) 250 lbs
(113.4 kg)
LCM2X1U LCM2X1UP
125 lbs 125 lbs 125 lbs 125 lbs
Installation Instructions LCM2X1U / LCM2X1UP
3
DIMENSIONS
1.16
29.4
COLUMN SOLD
SEPARATELY
8.58
217.8
DIMENSIONS: INCHES
[MILLIMETERS]
LCM2X1U
DIMENSIONS: INCHES
[MILLIMETERS]
LCM2X1U
1.83
46.6
LCM2X1U / LCM2X1UP Installation Instructions
4
0.13
3.2
23.62
600.0
[400mm
Mounting Pattern]
[600mm
Mounting Pattern]
LCM2X1U
LCM2X1U
DIMENSIONS: INCHES
[MILLIMETERS]
DIMENSIONS: INCHES
[MILLIMETERS]
Installation Instructions LCM2X1U / LCM2X1UP
5
DIMENSIONS (cont’d)
31.50
800.0
[800mm
Mounting Pattern]
LCM2X1U
LCM2X1UP
1.16
29.4
SEPARATELY
DIMENSIONS: INCHES
[MILLIMETERS]
DIMENSIONS: INCHES
[MILLIMETERS]
LCM2X1U / LCM2X1UP Installation Instructions
6
DIMENSIONS (cont’d)
32.50
825.5
TILT RANGE
-5° TO +20°
15.75
400.0
LCM2X1UP
[400mm
Mounting Pattern]
LCM2X1UP
DIMENSIONS: INCHES
[MILLIMETERS]
DIMENSIONS: INCHES
[MILLIMETERS]
Installation Instructions LCM2X1U / LCM2X1UP
7
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
LCM2X1U / LCM2X1UP Installation Instructions
8
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
3/32" (included)
1/8" (included)
5/32" (included)
3/16" (included)
1/2" or 13mm
M5 (included)
C (6)
E (6)
[Interface Bracket Hardware Kit]
A (8)
M4x16mm B (6)
M4x20mm M4x25mm D (6)
M5x16mm
M5x20mm F (6)
M5x25mm G (6)
M6x16mm H (6)
M6x25mm
I (6)
M8x20mm J (6)
M8x30mm K (4)
M8x50mm
L (8)
.750x.323x.250
M (8)
.750x.344x.500 N (8) P (1)
[Universal
washer]
Q (1)
3/32" S (1)
5/32"
R (3)
1/8"
T (1)
10-24 x 1/4" U (2)
5/16" x 1" V (2)
W (3)
5/16" x 3/4"
AA (1)
[In bag
M5
BB (1)
[Bottom coupling]
5/16"
[Bottom stop collar]
(Used with CPA Series
extension column system) (Used with 1-1/2"
NPT column system)
labeled "N"]
Z (4)
10-24
CC (1)
[Ceiling mount
assembly - LCM2X1UP]
OR
DD (1)
[Back cover]
EE (4)
[Interface bracket-
LCM2X1UP] OR
EE (4)
[Interface bracket-
LCM2X1U]
X (4)
10-24 x 2-1/4"
Y (4)
10-24 x 5/8"
CC (1)
[Ceiling mount
assembly - LCM2X1U]
(2 bags total - quantities listed per bag)
FF (1)
3/16"
Installation Instructions LCM2X1U / LCM2X1UP
9
INSTALLATION
IMPORTANT ! : Refer to Dimensions section to find specific
LCM2X1U/LCM2X1UP dimensions BEFORE proceeding with
installation.
NOTE: The following procedure assumes that a UL Listed CPA
or CMA ceiling plate (not included) and an extension
column (not included) has been properly installed
following instructions provided with ceiling plate and
extension column.
NOTE: Proceed to Attaching Mount to NPT Column section
or Attaching Mount to CPA Extension Column
section, as appropriate.
Attaching Mount to 1-1/2" NPT Column
CAUTION: WATCH FOR PINCH POINTS! Do not place
fingers between moveable parts.
1. Insert two 5/16 x 3/4" set screws (W) into back of ceiling
mount (CC). (See Figure 1)
Figure 1
2. Slide ceiling mount (CC) up from below onto installed
column (not included). (See Figure 2)
3. Tighten two 5/16" set screws installed in Step 1 against
column.
4. Thread bottom coupling (BB) onto installed column until tight,
with a minimum of four threads engaged. (See Figure 2)
5. Install and tighten one 10-24 x 1/4" set screw (T) into bottom
coupling (BB). (See Figure 2)
Figure 2
6. Loosen two installed set screws (W), and slide ceiling
mount down extension column until it rests on the bottom
coupling (B). (See Figure 3)
7. Retighten two 5/16" set screws (W) against column. (See
Figure 3)
Figure 3
(W) x 2
1
(CC)
2
5
(T)
(CC)
(BB)
4
7
(W) x 2
(B)
LCM2X1U / LCM2X1UP Installation Instructions
10
Attaching Mount to CPA Extension Column
CAUTION: WATCH FOR PINCH POINTS! Do not place
fingers between moveable parts.
1. Insert two 5/16 x 3/4" set screws (W) into back of ceiling
mount (CC). (See Figure 4)
Figure 4
2. Slide ceiling mount (CC) up from below onto installed
column (not included). (See Figure 5)
3. Tighten two 5/16" set screws installed in Step 1 against
column.
4. Slide bottom stop collar (AA) onto installed column, lining up
holes in collar with holes in column.
Figure 5
5. Install two 5/16" x 1" self-tapping screws (U) through two
5/16" flat washers (V), bottom stop collar (AA), and into
installed column. (See Figure 5)
6. Install and tighten 5/16" x 3/4" set screw (W) into bottom
stop collar (AA). (See Figure 5)
7. Loosen two installed set screws (W), and slide ceiling
mount down extension column until it rests on the bottom
stop collar (AA).
8. Retighten two 5/16" set screws (W) against column. (See
Figure 6)
Figure 6
Attaching Interface Brackets to Display
1. Lower the latch mechanism on each interface bracket (EE).
(See Figure 7)
Figure 7
(W) x 2
1
(CC)
2
(CC)
4
6
5
(U) x 2
(V x 2)
(AA)
(W) x 1
8
(W) x 2
(EE)
1
Latch
mechanism
Installation Instructions LCM2X1U / LCM2X1UP
11
2. Align the center of the interface bracket (EE) with center of
screen. (See Figure 8)
NOTE: The diamond-shape hole in the bracket corresponds to
the center of the mount.
Figure 8
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display. Properly sized
screws will easily and completely thread into display
mounting holes. If spacers are required, be sure to use longer
screws of the same diameter.
3. Select correct screws, spacers (if necessary) and universal
washers from the hardware bag (A-N) and attach brackets
(EE) to back of screen. (See Figure 8)
Attaching Display to Ceiling Mount
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! The displays MUST
be located equal distance from the column on each end of
the ceiling mount.
1. Ensure that the latch mechanisms on interface brackets
(EE) are already lowered. (See Figure 7)
2. While supporting both sides of display, lower display onto
one side of ceiling mount, hooking top of interface brackets
onto front of ceiling mount. (See Figure 9)
3. Raise the latch mechanism on both interface brackets to
lock bracket in place. (See Figure 9)
Figure 9
4. Fasten bracket against ceiling mount extrusion using one
10-24 x 5/8" button head cap screw (Y). (See Figure 10)
5. Repeat for other interface bracket.
Figure 10
6. While supporting both sides of second display, lower second
display onto other end of ceiling mount, hooking top of
interface brackets onto front of ceiling mount. (See Figure 9)
7. Repeat Steps 3 through 5 for second display.
Center of
bracket
(N)
(L or M)
(A-K)(EE)
3
2
2
3
3
Latch
mechanism
4
(Y) x 2
5
LCM2X1U / LCM2X1UP Installation Instructions
12
Adjustments
CAUTION: Watch for pinch points! Do not place fingers
between moveable parts.
Roll
The ceiling mounts allow up to 3° roll each direction.
1. Turn the roll adjustment bolt in the direction necessary for
the desired roll. (See Figure 11)
2. Stop adjusting when the desired setting is reached.
Figure 11
Tilt
The interface brackets allow -5° to 20° tilt, and can be locked at
0°, 10° and 20° tilt.
3. If necessary, loosen button head tilt friction bolt (located on
side of interface bracket). (See Figure 12)
4. Adjust tilt as required. (See Figure 12)
5. The tilt may be locked at 0°, 10° and 20° using one
10-24 x 2-1/4" Phillips head screw (X) and one 10-24 lock
nut (Z) per interface bracket. (See Figure 12)
6. Tighten button head tilt adjustment bolt as necessary.
Figure 12
OPTIONAL: Security
1. OPTIONAL: Add padlock (not included) to each interface
bracket to lock display to ceiling mount. (See Figure 13)
Figure 13
1
Roll
adjustment
bolt
Lock at
Lock at
Lock at
Tilt
friction
bolt
3
4
6
(Displays not shown)
5
(X)
(Z)
0° tilt
10° tilt
20° tilt
Padlock
(Optional)
Installation Instructions LCM2X1U / LCM2X1UP
13
2. Install back cover (DD) into four holes on back of ceiling
mount. (See Figure 14)
Figure 14
(DD)
LCM2X1U / LCM2X1UP Installation Instructions
14
Installation Instructions LCM2X1U / LCM2X1UP
15
LCM2X1U / LCM2X1UP Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
Chief, a products division of
Milestone AV Technologies
8800-002376 Rev03
2014 Milestone AV Technologies
www.chiefmfg.com
04/14
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Chief LCM2X1U Guide d'installation

LCM2X1U
Chief
Marque
Chief
Modèle
LCM2X1U
Catégorie
Mur
Taper
Guide d'installation
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes