Chief PAC392B Guide d'installation

Chief
Marque
Chief
Modèle
PAC392B
Catégorie
Kits de montage
Taper
Guide d'installation
INSTALLATION INSTRUCTIONS
Universal Wall Mounting Bracket
PAC392
PAC392 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies, and its affiliated corporations and
subsidiaries (collectively, "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to this bracket does not exceed the
weight rating of the rail mount attached to this bracket.
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
Installation Instructions PAC392
3
1/2"
(Provided)
1/8"
D (1)
A (2)
1/8"
C (4)
5/16"
B (4)
5/16"
REQUIRED TOOLS AND INCLUDED PARTS
DIMENSIONS
6.000
152.40
8.000
203.20
4.000
101.60
3.000
76.20
5.154
130.91
1.000
25.40
2.750
69.85
.492
12.49
.520
13.22
1.345
34.16
5.635
143.12
PAC392 Installation Instructions
4
INSTALLATION
WARNING: FAILURE TO PROVIDE ADEQUATE
STRUCTURAL STRENGTH FOR THIS COMPONENT CAN
RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE
TO EQUIPMENT! It is the installer’s responsibility to make
sure the structure to which this component is attached can
support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
NOTE: The PAC392 is compatible with the following wall
mounts: RMF2, RMT2, RLF2, RLT2.
1. Verify mounting brackets on wall bracket (A) can move
freely. (See Figure 1)
Figure 1
2. Locate desired installation location and slide upper
mounting plate into wall making sure bracket is seated in
channel bottom. (See Figure 2)
3. Let lower mounting plate rest against wall.
4. Using 1/2" socket, tighten tension screw until lower
mounting plate slides into channel in wall and continue
tightening until resistance is felt. (See Figure 2)
Figure 2
5. Tighten two upper and lower button head cap screws to
secure wall bracket (A) to wall. (See Figure 3)
6. Repeat for second wall bracket (A).
Figure 3
x 4
(A)
1
(A)
2
3
4
(A)
4
x4
A
5
5
Installation Instructions PAC392
5
IMPORTANT ! : If the display being installed has a recessed
mounting surface, the display must be assembled to the mount
prior to mount installation. See the installation instructions
included with the mount.
7. Install mount to PAC-392 using four 5/16" flat washers (B)
and four 5/16" lock nuts (C). (See Figure 4)
Figure 4
8. Attach display to mount.
(C) x 4
(B) x 4
(A)
Slat wall
Mount
PAC392 Installation Instructions
6
Installation Instructions PAC392
7
PAC392 Installation Instructions
Chief Manufacturing, a products division
of Milestone AV Technologies
8834-002001 Rev00
©2010 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
07/10
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P 800.582.6480 / 952.894.6280
F 877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P +31 (0)40 2668620
F +31 (0)40 2668615
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099
F 852 2145 4477
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Chief PAC392B Guide d'installation

Chief
Marque
Chief
Modèle
PAC392B
Catégorie
Kits de montage
Taper
Guide d'installation
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents