Simplicity BRUTE SNOW THROWER, 14.5TP 29 IN Manuel utilisateur

Manual Part No. 1738088

Revision A

Rev. Date 04/2009

Walk-Behind Snow Thrower

Mfg. No. Description

1695730 Dual Stage Snow Thrower, 14.5 TP, 29 Inch

Operator’s Manual

Not for

Reproduction

2

Thank you for purchasing this quality-built BRUTE snow thrower. We’re pleased that you’ve placed your confidence in the BRUTE brand.

When operated and maintained according to the instructions in this manual, your BRUTE product will provide many years of dependable

service.

This manual contains safety information to make you aware of the hazards and risks associated with snow throwers and how to avoid

them. This snow thrower is designed and intended only for snow throwing and is not intended for any other purpose. It is important that

you read and understand these instructions throroughly before attempting to start or operate this equipment. This snow thrower

requires final assembly before use. Refer to the Quck Start Guide for instructions on final assembly procedures. Follow the instructions

completely. Save these instructions for future reference.

Where to Find Us

You never have to look far to find Briggs & Stratton support and service for your snow thrower. Consult your Yellow Pages. There are

over 30,000 Briggs & Stratton authorized service dealers worldwide who provide quality service. You can also contact Briggs and Strat-

ton Customer Service by phone at (800) 528-5087, or on the Internet at www.brutepower.com.

Snow Thrower

Model Number

Revision

Serial Number

Engine

Model Number

Revision

Serial Number

Date Purchased

The Illustrated Parts List for this machine can be downloaded from www.brutepower.com. Please provide model and serial number

when ordering replacement parts.

Briggs & Stratton Power Products Group, LLC

P.O. Box 702

Milwaukee, WI 53201-0702

1-800-528-5087

brutepower.com

BRUTE is a trademark of Briggs & Stratton Power Products

Group, LLC Milwaukee, WI USA.

Not for

Reproduction

OPERATOR SAFETY.................................................................................... 4

FEATURES AND CONTROLS .......................................................................... 10

OPERATION ............................................................................................. 12

BEFORE OPERATING SNOW THROWER................................................................................. 12

CHECK THE TIRES .................................................................................................................. 12

OPERATE THE SNOW THROWER.............................................................................................................. 13

STOP THE SNOW THROWER.................................................................................................................... 13

EASY-TURNTM TRACTION CONTROL........................................................................................................ 14

TRACTION LOCK PINS ............................................................................................................................. 14

CHECK THE OIL (BEFORE STARTING ENGINE) ........................................................................................ 15

FILL THE FUEL TANK................................................................................................................................ 16

START THE ENGINE.................................................................................................................................. 16

STOP THE ENGINE.................................................................................................................................... 17

CLEAR A CLOGGED DISCHARGE CHUTE.................................................................................................18

OPERATING TIPS...................................................................................................................................... 18

MAINTENANCE ......................................................................................... 19

SERVICE RECOMMENDATIONS ............................................................................................................... 19

AFTER EACH USE..................................................................................................................................... 19

LUBRICATE AUGER GEAR BOX................................................................................................................. 20

LUBRICATE AUGER SHAFT FITTINGS ...................................................................................................... 20

CHECK/LUBRICATE FREE-HAND LINKAGE.............................................................................................. 20

LUBRICATE CHUTE ROTATION GEAR....................................................................................................... 20

ADUST THE DRAG ON THE CHUTE ROTATION......................................................................................... 20

ENGINE MAINTENANCE ........................................................................................................................... 21

CHANGE THE SPARK PLUG...................................................................................................................... 22

ADJUST SKID HEIGHT.............................................................................................................................. 23

BELT ADJUSTMENT.................................................................................................................................. 24

BELT GUIDE ADJUSTMENT ...................................................................................................................... 25

CHECK AND ADJUST THE CABLES.......................................................................................................... 25

EASY-TURNTM CABLE ADJUSTMENT ....................................................................................................... 27

AUGER SHEAR PIN REPLACEMENT......................................................................................................... 27

STORAGE................................................................................................ 28

OFF SEASON STORAGE............................................................................................................................ 28

LUBRICATE HEX SHAFT AND CHAINS..................................................................................................... 28

REMOVE FROM STORAGE........................................................................................................................ 28

TROUBLESHOOTING CHART.......................................................................... 29

WARRANTIES........................................................................................... 30

SPECIFICATIONS ....................................................................................... 31

3

TABLE OF CONTENTS

Not for

Reproduction

4

OPERATOR SAFETY

The safety alert symbol and signal word (DANGER,

WARNING, CAUTION, or NOTICE) is used to indicate the likeli-

hood and potential severity of personal injury and/or damage to

the product. In addition, a hazard symbol may be used to

represent the type of hazard.

Safety Alert Symbol and Signal Words

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE indicates a situation that could result in damage

to the

product

.

DANGER - Amputation Hazard

The discharge chute contains a rotating

impeller to throw snow. Never clear or unclog

the discharge chute with your hands. Fingers

can quickly become caught and traumatic

amputation or severe laceration will result.

Always use a clean-out tool to clear or unclog

the discharge chute.

Safety Alert – Identifies safety information about

hazards that can result in personal injury.

Operator’s Manual – Read and understand before

performing any activity or running snow thrower.

Rotating Impeller Keep a Safe

Distance from

Snow Thrower

Rotating Auger Rotating Gears

Never Reach into

Rotating Parts Thrown Objects

Fire Explosion

Shock Toxic Fumes

Hot Surface Recommended

Ear Protection for

Extended Use

Shut off engine and remove spark plug connector

before performing maintenance or repair work.

Hazard Symbols and Meanings

DANGER

• Hand contact with the rotating impeller inside the discharge

chute is the most common cause of injury associated with

snow throwers.

• This snow thrower is capable of amputating hands and feet,

and throwing objects. Read and observe all the safety

instructions in this manual. Failure to do so will result in

death or serious injury.

WARNING

U.S.A. Models: Certain components in this product and its

related accessories contain chemicals known to the state of

of California to cause cancer, birth defects, or other repro-

ductive harm. Wash hands after handling.

WARNING

U.S.A. Models: The engine exhaust from this product con-

tains chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

Not for

Reproduction

5

OPERATOR SAFETY

Oil

Fuel Forward

On Off Neutral

Choke Off Reverse

Choke On

Stop Electric Start -

Engage (Down) &

Disengage (Up)

Slow Engine - Run

Fast STOP Engine - Stop

Traction Control -

Engage (Down) Auger Control -

Engage (Down)

Auger Clutch Chute Deflector

(Up and Down)

Discharge Chute

(Left and Right) Heated Hand Grips

(High and Low)

Control Symbols on Equipment

12

F

Free-HandTM Control

Easy-TurnTM Traction Control

• Be thoroughly familiar with the controls and the proper use of the snow

thrower.

• Make sure you are properly trained before operating the snow thrower.

•Know how to stop the unit and disengage the controls quickly.

• Never allow anyone to operate the snow thrower without proper instruction.

• Always follow the instructions in the operator’s manual, if the snow thrower

will be stored for an extende d period.

• Maintain or replace safety and instruction labels as necessary.

• Never attempt to make major repairs on the snow thrower unless you have

been properly trained. Improper servicing of the snow thrower can result

in hazardous operation, equipment damage, and voiding of the product

warranty.

DANGER

Read, understand, and follow all the instructions on the

snow thrower and in the operator’s manual before operating

this unit.

Failure to observe the safet y instructions in this manual will

result in death or serious injury.

Read the Manual

TO SAFELY CLEAR A CLOGGED DISCHARGE CHUTE

DANGER: Hand contact with the rotating impeller inside the discharge

chute is the most common cause of injury associated with snow

throwers. Never use your hands to clean out the discharge chute.

FOLLOW THESE INSTRUCTIONS:

1. Shut OFF the engine.

2. Wait 10 seconds to be sure the impeller blades have stopped rotating.

3. Always use a clean-out tool, not your hands.

DANGER

Discharge chute contains rotating impeller to throw snow.

Never clear or unclog the discharge chute with your hands.

Fingers can quickly become caught in the impeller. Always

use a clean-out tool.

Failure to observe these safety instructions will result in

traumatic amputation or severe laceration.

Discharge Chute

NOTE: Not all control symbols shown on this page will appear

on your snow thrower. See FEATURES AND CONTROLS section

for the applicable symbols.

Not for

Reproduction

6

WHEN ADDING FUEL

• Turn off engine and let cool at least 2 minutes before removing the fuel

cap and adding fuel.

• Fill fuel tank outdoors or in a well ventilated area.

• Do not overfill the fuel tank. To allow for the expansion of gasoline, do not fill

above the bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights, heat, and other

ignition sources.

• Check fuel lines, cap, and fittings frequently for cracks or leaks. Replace if

necessary.

• Use an approved fuel container.

• If fuel spills, wait until it evaporates before starting engine.

WHEN STARTING ENGINE

• Ensure that spark plug, muffler, fuel cap, and air cleaner (if equipped) are in

place and secured.

• Do not crank the engine with the spark plug removed.

• If fuel is spilled, do not attempt to start the engine, but move the snow

thrower away from the area of the spill, and avoid creating any source of

ignition, until the fuel vapors have dissipated.

• Do not over-prime the engine. Follow the engine starting instructions in this

manual.

• If the engine floods, set choke (if equipped) to OPEN/RUN position, move

throttle (if equipped) to FAST position and crank until engine starts.

WHEN OPERATING EQUIPMENT

• Do not tip the snow thrower at an angle which causes the fuel to spill.

• Do not choke the carburetor to stop the engine.

• Never run the engine with the air cleaner assembly (if equipped) or the air

filter (if equipped) removed.

WHEN CHANGING OIL

• If you drain the oil from the top oil fill tube, the fuel tank must be empty or

fuel can leak out and result in a fire or explosion.

WHEN TRANSPORTING EQUIPMENT

• Transport with fuel tank EMPTY, or with fuel shut-off valve OFF.

WHEN STORING GASOLINE OR EQUIPMENT WITH FUEL IN TANK

• Store away from furnaces, stoves, water heaters, or other appliances that have

pilot light or other ignition source because they can ignite fuel vapors.

DANGER

Fuel and its vapors are extremely flammable and explosive.

Always handle fuel with extreme care.

Failure to observe these safety instructions can cause a fire

or explosion which will result in severe burns or death.

Fuel Handling

• Keep the area of operation clear of all persons, particularly small children

and pets.

• Thoroughly inspect the area where the snow thrower will be used and remove

all doormats, sleds, boards, wires, and other foreign objects.

• Do not operate the snow thrower without wearing adequate winter clothing.

• Wear footwear that will improve footing on slippery surfaces.

• Use caution to avoid slipping or falling especially when operating the

snow thrower in reverse.

• Never operate the snow thrower without good visibility or light. Always be

sure of your footing, and keep a firm hold on the handles.

• Do not clear snow across the face of slopes. Use extreme caution when

changing direction on slopes. Do not attempt to clear steep slopes.

• Do not overload the machine capacity by attempting to clear snow too

quickly.

• Never operate the snow thrower at high transport speeds on slippery

surfaces. Look behind the snow thrower and use care when operating in

reverse.

• Do not use the snow thrower on surfaces above ground level such as roofs of

residences, garages, porches, or other such structures or buildings.

• Operators should evaluate their ability to operate the snow thrower safely

enough to protect themselves and others from injury.

• The snow thrower is intended to remove snow only. Do not use the snow

thrower for any other purpose.

• Do not carry passengers.

• After striking a foreign object, shut OFF the engine, disconnect the cord on

electric motors, thoroughly inspect the snow thrower for any damage, and

repair the damage before restarting and operating the snow thrower.

• If the snow thrower vibrates abnormally, shut OFF the engine. Vibration is

generally a warning of trouble. See an authorized dealer if necessary for

repairs.

• For models equipped with electric starting motors, disconnect the power

cord after the engine starts.

DANGER

This snow thrower is only as safe as the operator. If it is

misused, or not properly maintained, it can be dangerous.

Remember you are responsible for your safety and that of

those around you.

Operation and Equipment Safety

OPERATOR SAFETY

Not for

Reproduction

7

• Keep children out of the area during operation. Children are often attracted to

the equipment. Be mindful of all persons present.

• Be alert and turn unit off if children enter the area.

• Never allow children to operate the unit.

• Use extra care when approaching blind corners, shrubs, trees, or other

objects that may obscure vision. Children may be present.

DANGER

Tragic accidents can occur if the operator is not alert to the

presence of children. Children are often attracted to the unit

and the operating activity. Never assume that children will

remain where you last saw them.

Children

• Start and run engine outdoors.

• Do not run the engine in an enclosed area, even if doors or windows are

open.

DANGER

Engines give off carbon monoxide, an odorless, colorless,

poison gas.

Breathing carbon monoxide can cause nausea, fainting,

or death.

Engine Safety

• Disengage all clutches and shift into neutral before starting the engine.

• Let the engine adjust to outdoor temperatures before starting to clear snow.

• Use a grounded three-wire plug-in for all snow throwers equipped with

electric drive motors or electric starting motors.

DANGER

Safe operation of the snow thrower requires the proper care

and maintenance of the engine. Failure to observe the safety

instructions in this manual will result in death or serious

injury.

• Always wear safety glasses or eye shields while during operation, and while

performing an adjustment or repair.

• Always be aware of the direction the snow is being thrown. Nearby

pedestrians, pets, or property may be harmed by objects being thrown.

• Be aware of your environment while operating the snow thrower. Running

over items such as, gravel, doormats, newspapers, toys, and rocks hidden

under snow, can all be thrown from the chute or jam in the auger.

• Use extreme caution when operating on or crossing gravel drives, walks, or

roads.

• Adjust the collector housing height to clear gravel or crushed rock surface.

• Never operate the snow thrower near glass enclosures, automobiles, window

wells, drop-offs, and the like without proper adjustment of the discharge

chute angle.

• Familiarize yourself with the area in which you plan to operate the snow

thrower. Mark off boundaries of walkways and driveways.

DANGER

Objects can be picked up by auger and thrown from chute.

Never discharge snow toward bystanders or allow anyone in

front of the snow thrower. Failure to observe these safety

instructions will result in death or serious injury.

Thrown Objects

• Whenever cleaning, repairing, or inspecting the snow thrower, make sure the

engine is OFF, spark plug wire is disconnected, and all moving parts have

stopped.

• Do not put hands or feet near or under rotating parts. Keep clear of the

discharge opening at all times.

• Never operate the snow thrower without proper guards, and other safety

devices in place and working.

• Never leave the snow thrower unattended while engine is running. Always

disengage the auger and traction controls, stop engine, and remove keys.

• Keep all loose clothing away from the front of the snow thrower and auger.

Scarves, mittens, dangling drawstrings, loose clothes, and pants can quickly

become caught in the rotating device and amputation will occur. Tie up

long hair and remove jewelry.

• Run the machine a few minutes after discharging snow to prevent freeze-up

of the collector/impeller.

• Disengage power to the collector/impeller when snow thrower is transported

or not in use.

DANGER

Keep hands, feet, and clothing away from rotating parts.

Rotating parts can contact or entangle hands, feet, hair,

clothing, or accessories.

Failure to observe these safety instructions will result in

traumatic amputation or severe laceration.

Moving Parts

OPERATOR SAFETY

Not for

Reproduction

8

• When performing any maintenance or repairs on the snow thrower, shut OFF

the engine, disconnect spark plug wire, and keep the wire away from the

plug to prevent someone from accidently starting the engine.

• Check shear bolts and other hardware at frequent intervals for proper

tightness to be sure the snow thrower is in safe working condition.

• Keep nuts and bolts tight and keep snow thrower in good condition.

• Never tamper with safety devices. Check their proper operation regularly and

make necessary repairs if they are not functioning properly.

• Components are subject to wear, damage, and deterioration. Frequently

check components and replace with recommended parts, when necessary.

• Check control operation frequently. Adjust and service as required.

• Use only factory authorized replacement parts when making repairs.

• Always comply with factory specifications on all settings and adjustments.

• Only authorized service locations should be utilized for major service and

repair requirements.

• Use only attachments and accessories approved by the factory (such as

wheel weights, counterweights, or cabs).

• Never attempt to make any adjustments while the engine is running (except

when specifically recommended by the factory).

WARNING

This snow thrower must be properly maintained to ensure safe

operation and performance. Failure to observe the safety

instructions in this manual could result in death or serious

injury.

Maintenance and Storage

-

• If there is natural or LP gas leakage in area, do not start engine.

• Do not use pressurized starting fluids because vapors are flammable.

WARNING

Starting engine creates sparking.

Sparking can ignite nearby flammable gases.

Explosion and fire could result.

• Never touch a hot engine or muffler. Allow muffler, engine cylinder, and fins

to cool before touching.

• Remove debris from muffler area and cylinder area.

• Install and maintain in working order a spark arrester before using equipment

on forest-covered, grass-covered, or brush-covered unimproved land.

•U

U.S.A. Models:

It is a violation of California Public Resource Code

Section 4442 to use or operate the engine on or near any forest-covered,

brush-covered, or grass-covered land unless the exhaust system is equipped

with a spark arrester meeting any applicable local or state laws. Other states

or federal areas may have similar laws.

WARNING

Running the engine produces heat. Engine parts, especially

muffler, become extremely hot.

Failure to observe these safety instructions could result in

severe thermal burns on contact.

Engine Safety (Continued)

OPERATOR SAFETY

Not for

Reproduction

9

Safety Decals Figure 1

Part No. 1737865

Chute Danger Decal

Part No. 1736616

Shift Decal

Part No. 1737866

Auger Danger Decal

Product ID Number &

Serial Number Decal

(Rear of Motor Box)

Engine Decals

Part No. 1737874

Main Dash Decal

THIS ENGINE MEETS 2008 CA EXH AND EPA

PHASE 2 EMISSION REGULATIONS FOR SMALL

OFF-ROAD ENGINES. REFER TO OWNER'S

MANUAL FOR MAINTENANCE SPECIFICATIONS,

ADJUSTMENTS, AND EMISSIONS

DURABILITY INFORMATION.

EPA EMISSIONS COMPLIANCE PERIOD: CATEGORY: X

CA COMPLIANCE PERIOD: X

DISP: XXXcc e11*97/68SA*XXXX/XX*XXXX*XX

FAMILY XXXXX.XXXXXX XXXXXX

IMPORTANT ENGINE INFORMATION

BRIGGS & STRATTON CORPORATION

Part No. 278297

Part No. 277953

Part No. 1737869

Auger Control Decal

Part No. 1737870

Traction Control Decal

122

Part No. 1738153

Easy-TurnTM Traction

Control Decal

Look for this symbol to indicate important safety

pre cautions. This symbol indicates: “Attention!

Become Alert! Your Safety Is At Risk.”

WARNING: I

If any safety decals become worn or damaged and

cannot be read, order replacement decals from your local dealer.

OPERATOR SAFETY

Before operating your snow thrower, read the safety decals

as shown on your snow thrower. The cautions and warnings

are for your safety. To avoid a personal injury or damage to

your snow thrower, understand and follow all the safety decals.

Not for

Reproduction

10

ENGINE CONTROLS

A. Choke Control — Used to start a cold engine (see Figure 2).

B. Electric Start Button — Used to start the engine using the electric

starter.

C. Primer Button — Used to inject fuel directly into the carburetor

manifold to ensure fast starts in cool weather.

D. Safety Key — Must be inserted to start engine. Pull out to stop. Do

not turn safety key.

E. Starter Handle — Starts the engine manually.

F. ON/OFF Switch

Engine Controls Figure 2

G. Fuel Tank and Cap

H. Oil Fill Cap

I. Engine Run/Stop (symbol location)

SNOW THROWER CONTROLS

A. Speed Select Lever — Allows the operator to use one of six (6)

forward and two (2) reverse speeds (see Figure 3). To shift, move

speed select lever to desired position.

NOTICE: Do not move speed select lever while Traction

Drive Clutch is engaged. This may result in severe damage

to drive system.

ENGINE AND SNOW THROWER CONTROLS

NOTICE: Read this OPERATOR’S MANUAL and OPERATOR SAFETY before operating your snow thrower. Compare the illustrations with your

SNOW THROWER to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference.

FEATURES AND CONTROLS

C

H

A

D

F

E

B

G

STOP

I

Not for

Reproduction

11

FEATURES AND CONTROLS

B. Auger Drive Clutch Lever — Used to engage and disengage the

auger and impeller. To engage push down, to disengage release.

C. Traction Drive Clutch Lever — Used to propel snow thrower for-

ward or reverse. Push down to engage, release to disengage.

D. Snow Chute Deflector — Used to change the direction the snow

is thrown.

E. Crank — Used to change direction of the snow discharge. Turn han-

dle clockwise to turn chute to right. Turn handle counterclockwise to

turn chute to left.

F. Skid Shoe — Used to adjust ground clearance of auger housing.

Snow Thrower Controls Figure 3

G. Clean-Out Tool — Used to remove snow and debris from the dis-

charge chute and the auger housing.

H. Free-HandTM Control — After engaging the traction control (left

hand) and auger control (right hand), allows the operator to

release the auger control lever to use the other controls.

I. Remote Chute Control — Push forward to discharge snow high

and far. Pull back to discharge snow down.

J. Easy-TurnTM Traction Control — When engaged, allows the oper-

ator to release the left traction wheel, but allows the right wheel to

continue driving for easy turning.

B

A

EC

12

F

G

D

H

J

I

Not for

Reproduction

12

Checking Tire Air Pressure Figure 4

BEFORE OPERATING SNOW THROWER

■

■Check the fasteners. Make sure all fasteners are tight.

■

■On electric start models, the unit was shipped with the starter cord

plugged into the engine. Before operating, unplug the starter cord from the

engine.

NOTE: This snow thrower was shipped WITH OIL in the

engine. See “Before Starting Engine” instructions in the

OPERATION section of this manual before starting engine.

CHECK THE TIRES

Check tires for damage. Check the air pressure in the tires with an

accurate gauge (see Figure 4).

CAUTION: Avoid Injury! Explosive separation of tire

and rim parts is possible when they are serviced

incorrectly.

• Do not attempt to mount a tire without the proper

equipment and experience to perform the job.

• Do not inflate the tires above the recommended pressure.

• Do not weld or heat a wheel and tire assembly. Heat can

cause an increase in air pressure resulting in an

explosion. Welding can structurally weaken or deform the

wheel.

• Do not stand in front or over the tire assembly when

inflating. Use appropriate tool that allows you to stand to

one side.

NOTICE: Check side of tire for maximum tire pressure. DO

NOT exceed maximum.

OPERATION

Not for

Reproduction

13

OPERATE THE SNOW THROWER

CAUTION: Operation with a Snow Cab. Wind may blow

exhaust gasses back towards the operator. If you notice

the smell of exhaust, change direction of operation.

The most effective use of the snow thrower will be established by experi-

ence, taking into consideration the terrain, wind conditions, and building

location which will determine the direction of the discharge chute.

NOTICE: Do not throw snow toward a building as hidden objects

could be thrown with sufficient force to cause damage.

1. Start the engine. See “To Start Engine” in this section.

2. Rotate the crank (C

C

, Figure 5) to set the direction (left or right) of the

discharge chute.

3. Pull the remote chute lever (D

D

) back to discharge the snow down.

Push the remote chute lever forward to discharge the snow high and

far.

CAUTION: Before operating, make sure the area in front

of the snow thrower is clear of bystanders or obstacles.

4. Fully press and hold the auger engage control (A

A

) on the right-hand

grip to begin auger rotation. Releasing the auger engage control will

disengage the auger - unless the Free-Hand™ Control has been acti-

vated.

WARNING: Read Operator’s Manual before operating

machine. This machine can be dangerous if used

carelessly.

• Never operate the snow thrower without all guards, covers,

shields in place.

• Never direct discharge towards windows or allow

bystanders near machine while engine is running.

• Stop the engine whenever leaving the operating position.

• Disconnect spark plug before unclogging the impeller

housing or the discharge chute and before making repairs

or adjustments.

• When leaving the machine, remove the safety key. To reduce

the risk of fire, keep the machine clean and free from spilled

gas, oil, and debris.

WARNING: Never run engine indoors or in an enclosed,

poor ventilated area. Engine exhaust contains CARBON

MONOXIDE, an ODORLESS and DEADLY GAS.

• Keep hands, feet, hair, and loose clothing away from any

moving parts on engine and snow thrower.

• Temperature of muffler and nearby areas can exceed

150°F (66°C). Avoid these areas.

• DO NOT allow children or young teenagers to operate or

be near snow thrower while it is operating.

7. Use the speed select lever (E

E

) to select the forward drive speed. Set the

speed select lever to one of the following positions as determined by

snow conditions:

1-2 Wet, Heavy, Slushy, Extra Deep

3 Moderate

4-5 Very Light

6 Transport

NOTE: When clearing wet, heavy, snow, it is recommended

that the ground speed of the unit be reduced, maintained full

throttle and do not attempt to clear the full width of the unit.

8. To stop moving forward, release the traction control lever (B

B

).

9. To move the snow thrower backwards, move the speed select lever into

either first or second reverse position and engage the traction control

lever.

STOP THE SNOW THROWER

1. Release the auger engage control (A

A

, Figure 5).

2. Release the traction control lever (B

B

).

3. Push the ON/OFF switch (A

A

, Figure 14) to the OFF position and pull

out the safety key (B

B

).

NOTE: Always release the traction control lever before moving

the speed select lever.

Control Levers Figure 5

12

F

Free-HandTM Control

5. Fully press and hold the traction and Free-Hand™ Control lever (B

B

) on

the left-hand grip to engage the traction drive and begin moving the

snowthrower. To disengage the traction drive, completely release the

lever.

6. When BOTH levers are depressed, the Free-Hand™ Control is acti-

vated. This allows auger engage control to be released - YET AUGER

ROTATION WILL CONTINUE - until the Free-Hand™ Control is re-

leased.

B

E

D

A

C

OPERATION

WARNING: The operation of any snow thrower can result in foreign objects being thrown into the eyes, which can result in

severe eye damage. Always wear safety glasses or eye shields before beginning snow thrower operation. We recommend

standard safety glasses or Wide Vision Safety Mask over spectacles.

Not for

Reproduction

14

EASY-TURNTM TRACTION CONTROL

For easy turning when using the snow thrower, squeeze the Easy-TurnTM

lever (see Figure 6).

Engaging the Easy-TurnTM lever releases the left traction wheel but allows

the right wheel to continue driving. Releasing the Easy-TurnTM lever auto-

matically engages both drive wheels for full traction (see Figure 7).

NOTE: The Easy-TurnTM will be more difficult to activate under a

heavy load. Activate the lever before beginning a turn.

Easy-TurnTM Control Figure 6

Full Traction Figure 7

Traction Lock Pins Figure 8

A

TRACTION LOCK PINS

The right traction wheel can be completely released using the locking pin

(A

A

, Figure 8). This allows the unit to be easily moved with the engine off.

OPERATION

Not for

Reproduction

15

OPERATION

CHECK THE OIL (BEFORE STARTING ENGINE)

NOTE: The engine was shipped from the factory filled with oil.

Check the level of the oil. Add oil as needed.

1. Make sure the unit is level. Use a high quality detergent oil classified

“For Service SG, SH, SJ, SL, or higher”.

2. Remove the oil fill cap/dipstick (A

A

, Figure 9) and wipe with a clean cloth.

3. Insert the oil fill cap/dipstick and turn clockwise to tighten.

4. Remove the oil fill cap/dipstick and check the oil.

NOTE: Do not check the level of the oil while the engine runs.

5. If necessary, add oil until the oil reaches the FULL mark on the oil fill

cap/dipstick. Do not add too much oil.

6. Tighten the oil fill cap/dipstick securely each time you check the oil

level.

NOTE: For extreme cold operating conditions of 0°F (-18°C) and

below, use a synthetic 5W30 motor oil for easier starting.

NOTE: S.A.E. 5W30 motor oil may be used to make starting

easier in areas where the temperature is 20°F (-7°C) to 0°F

(-18°C). Synthetic 5W30 is acceptable for all temperatures.

DO NOT mix oil with gasoline. See Chart for oil

recommendations.

F −20 0 20 32 40

C −30 −20 −10 0 10

5W30

Synthetic 5W30

SAE VISCOSITY GRADES

TEMPERATURE TYPE OF OIL

0°F (-18°C) and above S.A.E. 5W30

0°F (-18°C) and below Synthetic 5W30

FULL

Checking the Oil

Figure 9

A

Not for

Reproduction

16

Start the engine as follows:

1. Check the oil level. See the “Check/Add Oil” section in the ENGINE

MANUAL.

2. Make sure equipment drive controls are disengaged.

3. Push the ON /OFF switch (A

A

, Figure 10) to the ON position.

Starting Engine Figure 10

4. Insert the safety key (A

A

, Figure 11) into the safety key slot and push

fully in to the RUN position.

5. Turn the choke knob (B

B

) fully clockwise if engine is cold.

NOTE: Do not use the choke to start a warm engine.

6. Push the primer button (C

C)

two times.

NOTE: Do not use the primer to start a warm engine.

NOTE: Ensure that electric extension cord is removed from the

power receptacle.

FILL THE FUEL TANK

This engine is certified to operate on gasoline. Exhaust Emission Control

System: EM (Engine Modifications).

Fill the fuel tank with fresh, clean, unleaded regular, unleaded premium, or re-

formulated automotive gasoline with a minimum of 85 octane along with a

fuel stabilizer (follow instructions on fuel stabilizer package). D

DO NOT

use

leaded gasoline. We recommend that fuel stabilizer be added to the fuel

each time that gasoline is added to the fuel tank.

NOTE: Winter grade gasoline has higher volatility to improve

starting. Be certain container is clean and free from rust or

other foreign particles. Never use gasoline that may be stale

from long periods of storage in the container.

CAUTION: DO NOT use gasoline containing any

amount of alcohol as it can cause serious damage to

the engine or significantly reduce the performance.

START THE ENGINE

Be sure that engine oil is at FULL mark on the oil fill cap/dipstick. The snow

thrower engine is equipped with an A.C. electric starter and recoil starter. Before

starting the engine, be certain that you have read the following information.

If engine floods, set the choke to the OPEN/RUN position and crank until the en-

gine starts.

WARNING: The electric starter is equipped with a

three−wire power cord and plug designed to operate on AC

house hold current. The power cord must be properly

grounded at all times to avoid the possibility of electric shock

which can cause injury to the operator. Follow all instructions

carefully as set forth:

Make sure your house has a three−wire grounded system.

If you are not sure, ask a licensed electrician. If your house does

not have a three−wire grounded system, do not use this electric

starter under any condition.

If your house has a three−wire grounded system but a three-hole

receptacle is not available to connect the electric starter, have a

three−hole receptacle installed by a licensed electrician.

WARNING: To connect power cord, always connect the

power cord first to the switch box located on the

engine and then plug the other end into a three−hole

grounded receptacle.

WARNING: To disconnect the power cord, always

unplug the end connected to the three−hole grounded

receptacle first.

WARNING: Gasoline is flammable. Always use

caution when handling or storing gasoline. Turn

engine off and let engine cool at least two minutes before

removing the gas cap. Do not add gasoline to the fuel tank

while snow thrower is running, hot, or when snow thrower

is in an enclosed area. Keep away from open flame,

electrical sparks and DO NOT SMOKE while filling the fuel

tank. Never fill the fuel tank completely; but fill the fuel

tank to within 1-1/2 inches (3.8 mm) from the top to

provide space for the expansion of the fuel. Always fill fuel

tank outdoors and use a funnel or spout to prevent spilling.

Make sure to wipe up any spilled fuel before starting the

engine.

Store gasoline in a clean, approved container, and keep

the cap in place on the container. Keep gasoline in a cool

well ventilated place; never in the house. Never buy more

than a 30 day supply of gasoline to assure volatility.

Gasoline is intended to be used as a fuel for internal

combustion engines; therefore, do not use gasoline for any

other purpose. Since many children like the smell of

gasoline, keep it out of their reach because the fumes are

dangerous to inhale, as well as being explosive.

A

OPERATION

Not for

Reproduction

17

OPERATION

Inserting Safety Key Figure 11

7. Rewind Start: Firmly hold the starter cord handle (A

A

, Figure 12). Pull

the starter cord handle slowly until resistance is felt, then pull rapidly.

WARNING: Rapid retraction of the starter cord (kickback)

will pull your hand and arm toward the engine faster

than you can let go. Broken bones, fractures, bruises,

or sprains could result. When starting engine, pull the

starter cord slowly until resistance is felt and then pull

rapidly to avoid kickback.

NOTE: If the engine does not start after three attempts, see the

Engine Manual Troubleshooting section.

8. Electric Start: First connect the extension cord to the power cord

receptacle and then into a wall receptacle. If additional extension cord is

required, make sure it is three-wire.

WARNING: If the extension cord is damaged, it must

be replaced by the manufacturer (or its service agent)

or a similarly qualified person to avoid a hazard.

Starting with Electric Start Figure 13

IMPORTANT: To extend the life of the starter, use short

starting cycles (five seconds maximum). Wait one minute

between starting cycles.

NOTE: If the engine does not start after three attempts, see the

Engine Manual Troubleshooting section.

Starting with Cord Handle Figure 12

A

B

C

A

B

STOP THE ENGINE

Before stopping the engine for a few minutes to help dry off any moisture

on the engine.

WARNING: Gasoline and vapors are extremely

flammable and explosive. Fire or explosion can

cause severe burns or death. DO NOT choke the

carburetor to stop the engine.

1. Push the ON/OFF switch (A

A

, Figure 14) to the OFF position.

2. Remove the safety key (B

B

). Keep the safety key out of the reach of

children.

Stopping Engine Figure 14

NOTE: Do not lose the safety key. Keep the safety key in a safe

place. The engine will not start without the safety/ignition key.

A

B

9. Electric Start: Depress the starter push button (A

A

, Figure 13). After you

start the engine, first disconnect the extension cord from the wall receptacle

and then from the power cord receptacle (B

B

).

A

Not for

Reproduction

1818

CLEAR A CLOGGED DISCHARGE CHUTE

DANGER: Hand contact with the rotating impeller inside

the discharge chute is the most common cause of injury

associated with snow throwers. Never clear or unclog

discharge chute with your hands, or while engine is

running. Fingers can quickly become caught and

traumatic amputation or severe laceration can result.

OPERATING TIPS

1. Most efficient snowthrowing is accomplished when snow is removed

immediately after it falls.

2. For complete snow removal, slightly overlap each swath previously taken.

3. Snow should be discharged downwind whenever possible.

4. For normal usage, set the skids 1/8 inch (3 mm) below the scraper

bar. For extremely hard-packed snow surfaces, the skids may be ad-

justed upward to ensure cleaning efficiency.

5. On gravel or crushed rock surfaces, the skids should be set at 1-1/4

inch (32 mm) below the scraper bar (see “Adjust Skid Height” in the

MAINTENANCE section of this manual). Rocks and gravel must not

be picked up and thrown by the machine.

6. After the snowthrowing job has been completed, allow the engine to

idle for a few minutes, to melt snow and ice accumulated on the

engine.

7. Clean the snow thrower thoroughly after each use.

8. Remove ice and snow accumulation and all debris from the entire

snow thrower, and flush with water (if possible) to remove all salt or

other chemicals. Wipe snow thrower dry.

9. Before starting snow thrower, always inspect augers and impeller for

ice accumulation and/or debris, which could result in snow thrower

damage.

10. Check oil level before every start. Make sure the oil is at the FULL

mark on the oil fill cap/dipstick.

Clean-Out Tool Figure 15

A

• SHUT OFF THE ENGINE!

• Wait 10 seconds to be sure that the impeller blades have stopped

rotating.

• Always use a clean-out tool, not your hands.

A clean-out tool (A

A

, Figure 15) is attached to either the handle or the top of the

auger housing. Use the clean-out tool to remove snow from the auger housing.

OPERATION

Not for

Reproduction

19

MAINTENANCE

SERVICE RECOMMENDATIONS

PROCEDURE

FIRST

2

HOURS

BEFORE

EACH

USE

OFTEN

EVERY

5

HOURS

EVERY

10

HOURS

EVERY

25

HOURS

BEGINNING

EACH

SEASON

BEFORE

STORAGE

SNOW THROWER

Tighten all Screws and

Nuts ✓ ✓ ✓

Check Traction Clutch

Cable Adjustment (See

Cable Adjustment)

✓ ✓

Check Auger Clutch

Cable Adjustment (See

Cable Adjustment)

✓ ✓ ✓

Adjust Drive Belts ✓ ✓ ✓

Lubricate Chains and Hex

Shaft ✓ ✓

Lubricate Auger Shaft

(See Shear Pin Replace-

ment)

✓ ✓

Lubricate Free-Hand

Linkage ✓ ✓ ✓

ENGINE Oil, Check ✓ ✓ ✓

Oil, Change ✓ ✓ ✓

NOTE: The warranty on this snow thrower does not cover items

that have been subjected to operator abuse or negligence. To

receive full value from the warranty, operator must maintain

snow thrower as instructed in this manual.

The above Service Recom mendations are supplied to assist the opera-

tor to properly maintain the snow thrower. This is a check list only. Adjust-

ment referred to will be found in the MAINTENANCE section of this

manual.

AFTER EACH USE

1. Check for any loose or damaged parts.

2. Tighten any loose fasteners.

3. Check and maintain the auger.

4. After each use, remove all snow and slush off the snow thrower to

prevent freezing of auger or controls.

5. Check controls to make sure they are functioning properly.

6. If any parts are worn or damaged, replace immediately.

Not for

Reproduction

20

LUBRICATE AUGER GEAR BOX

The auger gear box is lubricated at the factory and should not require

additional lubrication. If for some reason the lubricant should leak out,

or if the auger gear box has been serviced, add Lubriplate GR132 Grease or

equivalent. Maximum 3- 1/4 ounces, (92 grams) should be used.

Remove filler plug (A

A

, Figure 16), once a year. If grease is visible, do not

add. If grease is not visible, use a piece of fine wire, like a dipstick to check

if there is grease in the gear box. Mobilux EP1 and Shell Alvania EP1 are

suitable equivalents.

Lubricating Auger Gear Box Figure 16

LUBRICATE AUGER SHAFT FITTINGS

1. Using a hand grease gun, lubricate the auger shaft fittings (B

B

, Figure

16) every ten (10) operating hours. Each time a shear pin is replaced,

the auger shaft (C

C

) MUST be greased. (See “Auger Shear Pin Replace-

ment” section.)

2. For storage or when replacing shear pins, remove shear pins and

lubricate auger shaft fittings (B

B

). Rotate augers several times on the

shaft and reinstall the shear pins.

CHECK/LUBRICATE FREE-HAND LINKAGE

Check the function of the Free-Hand controls. The controls should function

as described in the OPERATION section.

WARNING: It is critical for the safe operation of the

unit that the controls disengage when released.

If the controls do not function properly, l

lubricate the controls

(see

Figure 17).

NOTICE: Under no circumstances should the unit be used if the

controls do not function properly.

C

A

B

Lubricating Controls Figure 17

LUBRICATE CHUTE ROTATION GEAR

Lubricate the chute rotation gear (A

A

, Figure 18) and shaft (B

B

) with automo-

tive type oil every twenty-five (25) operating hours .

ADJUST THE DRAG ON THE CHUTE ROTATION

NOTE: After repeated use, the chute rotation gear may loosen,

causing the chute to move back to the center position.

Adjust the drag by tightening the nut (C

C

, Figure 18). Tightening the nut will

limit the chute from moving without the operator turning the chute rotation

crank.

Chute Rotation Gear Figure 18

C

A

B

MAINTENANCE

Not for

Reproduction

La page charge ...

Simplicity BRUTE SNOW THROWER, 14.5TP 29 IN Manuel utilisateur

Simplicity BRUTE SNOW THROWER, 14.5TP 29 IN Manuel utilisateur

dans d''autres langues