Room Air Conditioner

Installation & Operations Manual

Manual de Instalaci6n y Funcionamiento

Manuel d'installation et d'utilisation

Room air conditioners for

double hung windows &

through-the-wall Installation

Acondicionadores de aire para

ventanas de guillotina y

ENGLISH

Operation ................................................ 6

Maintenance ........................................................... 7

Warranty ..........................................................

ESPAIXIOL

Instrucclones importantes de seguridad ................. 10

Instalacion ............................................. 11

Funcionamiento ................................................... 14

Mantenimiento ............................................ 15

Garant a ................................................................ 18

FRANI_AIS

Write down the model and serial numbers

The model and serial numbers can be found on the side of the

cabinet near the control panel. Use these numbers in any

correspondence or service calls concerning your air

conditioner.

Para referencia futura

Escriba el numero de modelo y de serie

El numero de modelo y de serie se encuentran en el costado

del gabinete cerca del panel de control, Use estos numeros en

toda la correspondencia o Ilamadas de servicio relacionadas

correspondance ou appel au service apres-vente ayant trait au

climatiseur.

Model No., No. de Modelo, N° de module

Serial No., No. de Serie, N° de s#rie

Date of Purchase, Fecha de Compra, Date d'achat

For additional questions please call

1-217-347-6459 or e-maih

customerservice@coolmate, biz

Para mayor informaci6n por favor Ilame al

PROTECTORSEE WIREGAUGE

15 AMP #14 MINIMUM

20 AMP #12 MINIMUM

30 AMP #10 MINIMUM

Electrical Shock Hazard

Important Grounding Requirements

hung windows with actual opening width of 26 7/8" to 41 5/8" and clear,

vertical opening of 15 5/8" minimum from bottom of sash to sill. Unit can

be installed in 23 7/8" wide window, if cabinet side seals are removed.

Tools Needed

Screwdrivers Ratchet or Driver with 1/4" socket

1" wood screw 1

5/8" wood screw 5

A_::_ ctual size

Decorative Front Removal

_ ake sure unit is unplugged before removing the

Removing the Chassis

1, Remove the two (2) shipping screws from the rear bottom side of the

cabinet. These shipping screws may be discarded.

2, Remove the two (2) antitheft screws from the bottom front sides of

the cabinet. RETAIN THESE SCREWS, they will be replaced later in

the installation.

3, Slide the chassis out of the cabinet by grasping the base pan handle

and pulling forward while bracing the top bar.

_ ake sure unit is unplugged before removing chassis

from cabinet.

of the cabinet and sharp coils to avoid injury or torn

(_ Anti-theft screws

Side View

Securing the Filler Panels

block airflow outside with shrubs, enclosures, or other

23-23-0355N-002

3, Close window until it touches behind air conditioner top bar.

4, Fasten top bar to window frame using 5/8" washer head screw.

5, If filler is required on sides of air conditioner, cut plastic foam seal

7, Install chassis into cabinet.

Consult your authorized dealer or importer for alternative

Through-the-wall Installation

This air conditioner is designed as a slide-out type chassis, making it

possible to install it through-the-wall in both existing and new

• It is important that you inspect the condition of the wall where the air

conditioner will be installed.

and cabinet to prevent moisture from getting to the interior of the

Fig. 3

(_ Cabinet

(_ Bottom Bar

(_ Interior wall

(E) Decorative Front

C) Minimum lx6 wood

support (nailed or

screwed to wood

frame)

(E)2" Wood frame

(_1 1/2" space

Power Control

The Power Control turns the unit on and

off.

Set Temperature/

Timer Oisplay

Shows the set temperature when the unit

is in operation and hours when the timer

is being set. THE TEMPERATURE

DISPLAY ONLY SHOWS THE SET

TEMPERATURE, NOT THE ACTUAL

ROOM TEMPERATURE,

buttons at once, the display will toggle

the timer is being set, these buttons are

used to change the hour setting in

increments of 1 from 00 to 24.

Mode Control

currently being utilized.

The unit will circulate and cool the air.

Heat Mode (Heat Models Only) -

The unit will circulate and heat the air.

Heater Safety Feature- When heater is

powered off, low fan will automatically stay

on and run for 60 seconds to ensure the

removal of residual heat, meanwhile, the

Low Fan LED blinks until the low fan stops.

Fan Mode-

The unit will only circulate the air.

Energy Saver Mode -

compressor cycles back on, the unit will

will change automatically as the

The settings are adjusted with the Fan Speed Control, each time the button is

being used.

When the Auto feature is selected while the air conditioner is in the Cool or Heat

mode, the fan speeds will change automatically as the temperature in the room

changes. In Cool Mode when the room reaches 7° or more above the set temperature

High Fan will be used, 4° or less above the set temperature will use Low fan. In Heat

Mode when the room reaches 7° or more below the set temperature High fan will be

used, 4° or less below the set temperature will use Low fan. At all other times the fan

will use Medium fan.

the Timer mode:

power is OFF. The display will read 00.

2. The display will show the amount of

4. A green light next to the Timer

using the Timer mode:

1. Push the timer button while the

power is ON. The display will read 00.

Adjust the display to show the desired

using the Temperature/Timer adjustment

return to the set temperature after 10

seconds.)

2. To display the amount of time left

until SHUT-DOWN, push the Timer

button once.

3. To exit Timer mode, push the Timer

button twice.

Air Conditioner Remote Control

• Do not attempt to recharge, short, or disassemble.

Keep batteries and other things that could be swallowed away from young

Electronic Control (Cooling Only)

Mechanical Control (Cooling Only)

minutes before restarting.

Mechanical Control Panel

Open Vent Door - When the vent door is open it allows for fresh air to circulate and

for stale air to be removed from the room, Maximum air circulation and cooling occur

when the vent door is CLOSED,

Master Control - The Master Control turns the unit off and on, It is also used to select

the desired function of the unit such as High Cool, Medium Cool, Low Cool, High

Fan, Medium Fan (on some models) or Low Fan, When one of the fan functions is

air when one of the Cool functions is selected,

Thermostat - The Thermostat Control adjusts the sensitivity of the unit thermostat,

which regulates the room temperature by automatically turning the compressor on

and off, The cooler the setting, the cooler the room temperature will be,

Cooling Operation

2, Turn the Thermostat Control to

"Cooler",

3, Turn the Master Control to

comfort, turn the Thermostat

operation),

5, When the desired comfort level is

turned to "Low Cool",

6, To turn off unit or in the event of a

power interruption, turn the Master

Control to OFF,

Heating Operation

1 Close vent door

4, If room becomes too warm for comfort,

turn the Thermostat clockwise until the

heating elements turn off (air circulating

fan will remain in operation), The

temperature will be automatically

desired comfort level,

5, When the desired comfort level is

6, To turn unit off, or in event of power

1. Turn Master Control to OFF,

2. Remove the air filter by opening the air intake panel on the decorative front and

pull it out of the unit,

3. Wash in hot soapy water, rinse and shake dry,

4. Replace the filter, with the front of the filter toward you,

5. To dry the filter thoroughly, run your unit for a few minutes, Remember, only a

clean filter works properly and delivers top efficiency at every setting,

_ ote: Failure to keep air filter clean will result in poor air circulation.

Proper use and care of your air conditioner will help ensure longer life of the

unit. It is recommended to annually inspect and clean the coils and condensate

water passages. Expense of annual inspection is the consumer's responsibility.

Service To save time and expense, check the following before calling an authorized service station.

Insufficient Cooling

remains high. If this happens, simply turn the unit off and allow

Insufficient Heating- Heating Models Only

For Models Installed in North America - If Service or Parts are Required First, make the recommended checks. If it appears that

service or parts are still required, see your room air conditioner warranty "How to Obtain Warranty Service or Parts".

For Models Installed Outside North America For room air conditioners purchased for use outside North America, the

manufacturer does not extend any warranty either expressed or implied. Consult your local dealer for any warranty terms

extended by the importer in your country.

Troubleshooting Guide

Occurrence

Air from unit does not

feel cold enough

Air conditioner cooling,

Water dripping inside • Improper installation.

Solutions

use. Ready access to the air conditioner for service is the responsibility of the owner.

In addition to the full (one year) parts and labor warranty described above, Fedders Appliances will, through its authorized servicers

Note: In the event of any required parts replacement within the period of this warranty, Fedders Appliances replacement parts shall be used and

Exceptions

failure to provide reasonable and necessary maintenance or to follow the written Installation and Operating Instructions. If the unit

is put to commercial, business, rental, or other use or application other than for consumer use, we make no warranties, express or

implied, including but not limited to, any implied warranty of merchantability or fitness for particular use or purpose.

Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion or limitation of incidental