Avocent SwitchView 130 Quick Installation Manual
- Taper
- Quick Installation Manual
The following instructions will help you
install your SwitchView 130 KVM switch.
Should you require further assistance,
please contact Avocent Technical Support.
The SwitchView 130 2-port switch
enables access and management of
attached DVI/USB PCs, while supporting
audio and microphone capabilities.
1
Connecting power
Plug in the power adaptor to the power
receptacle located on the back of the
SwitchView 130 switch.
2
Connecting local peripherals
Connect the keyboard, monitor, mouse,
speakers and microphone to the
appropriate console connectors on the
front of the SwitchView 130 switch
using the supplied cables.
3
Connecting your PCs
Connect one end of the included DVI
cable to the switch, then connect the
other end to a PC. Connect the included
USB cable with Type A connecting to
the PC and Type B connecting to the
switch. Repeat these steps to connect
your second PC.
4
Operating the SwitchView 130
switch
There are two ways to switch channels
(PCs) on the SwitchView 130 switch: a
front panel push-button or a configurable
hotkey sequence.
Using the front panel button
Press the front panel button to switch
PCs. The button will illuminate green for
Port 1 and blue for Port 2.
Using the hotkey sequence
To select your PC, activate the hotkey
sequence by pressing ScrLk + ScrLk.
You will automatically switch PCs.
Each keystroke must be pressed within
two seconds to validate the hotkey
sequence.
QUICK INSTALLATION GUIDE SwitchView
®
13 0 2-port DVI/USB KVM Switch
To Contact Avocent Technical Support: Visit www.avocent.com 590-872-501A
Avocent, the Avocent logo, The Power of Being There and SwitchView are registered trademarks of Avocent Corporation or its affiliates in the U.S. and other countries. ©2008 Avocent Corporation.
2
3
4
1
Back
User
PCs
Front
SwitchView 130 switch (2-port)
QUICK INSTALLATION GUIDE SwitchView
®
13 0 2-port DVI/USB KVM Switch
NOTE: Optional software for the
SwitchView 130 switch is available for
download. Visit www.avocent.com to
download this application at no cost. This
software is not required for your switch to
operate. It adds auto scanning and fixed
audio control to switching capabilities. This
application will need to be loaded on each
PC attached to your switch in order for you
to utilize these additional controls.
For additional information
Visit www.avocent.com for more
information on your SwitchView 130
switching system.
USA Notification
Warning: Changes or modifications to
this unit not expressly approved by the
party responsible for compliance could
void the user’s authority to operate the
equipment.
Note: This equipment has been tested
and found to comply with the limits for
a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits
are designed to provide reasonable
protection against harmful interference
when the equipment is operated in a
commercial environment. This equipment
generates, uses and can radiate radio
frequency energy and, if not installed
and used in accordance with the
instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a
residential area is likely to cause harmful
interference in which case the user will
be required to correct the interference at
his own expense.
Canadian Notification
This digital apparatus does not exceed
the Class B limits for radio noise
emissions from digital apparatus set out
in the Radio Interference Regulations
of the Canadian Department of
Communications.
Le présent appareil numérique n’émet
pas de bruits radioélectriques dépassant
les limites applicables aux appareils
numériques de la classe B prescrites
dans le Règlement sur le brouillage
radioélectrique édicté par le Ministère
des Communications du Canada.
European Union Declaration of
Conformity
This equipment has been tested
and found to comply with the limits
for a Class B computing device in
accordance with the specifications
in the European standard EN55022.
These limits are designed to provide
reasonable protection against harmful
interference. This equipment generates
uses and can radiate radio-frequency
energy, and if not installed and used in
accordance with the instructions, might
cause harmful interference to radio or
television reception. However, there is
no guarantee that harmful interference
will not occur in a particular installation. If
this equipment does cause interference
to radio or television reception, which
can be determined by turning the
equipment on and off, you can correct
the interference with one or more of the
following measures:
a) Reorient or relocate the receiving
antenna.
b) Increase the separation between
the equipment and the receiver.
c) Connect the equipment to an
outlet on a circuit different from that to
which the receiver is connected.
To Contact Avocent Technical Support: Visit www.avocent.com 590-872-501A
Avocent, the Avocent logo, The Power of Being There and SwitchView are registered trademarks of Avocent Corporation or its affiliates in the U.S. and other countries. ©2008 Avocent Corporation.
-
1
-
2
Avocent SwitchView 130 Quick Installation Manual
- Taper
- Quick Installation Manual
dans d''autres langues
- English: Avocent SwitchView 130
Documents connexes
-
Avocent SWITCHVIEW PC Quick Installation Manual
-
Avocent SwitchView 100 Quick Installation Manual
-
-
-
-
-
-
-
-