Digital Monitoring Products 1106 Universal Transmitter Guide d'installation

Marque: Digital Monitoring Products

Modèle: 1106 Universal Transmitter

Catégorie: Lecteurs de contrôle d'accès

Taper: Guide d'installation

Ce manuel convient également à

1106

1106 SERIES WIRELESS

UNIVERSAL TRANSMITTERS

Installation Guide

The 1106 Series Wireless Universal

Transmitters oer two-inputs

typically used for door and window

applications. The 1106 features built-

in optional 128-bit AES encryption.

The 1106 Series provides a cover

tamper, magnetic reed switch, and

an on-board terminal block to allow

for external contact wiring.

Both contacts, internal and external,

can be programmed to operate

at the same time. This allows two

independent zones to operate from

one 1106.

The 1106 Series also features

Disarm/Disable functionality. When

this option is set to YES, Zone

Tripped messages are disabled

when the system is disarmed to

allow for extended transmitter

battery life. Supervision, Tamper,

and Low Battery are the only

messages that are sent to the panel

when the system is disarmed.

Compatibility

What is Included?

• One 1106 Wireless Universal

Transmitter

• One magnet with standard and

commercial housing and base

• One 3.0V lithium CR123A battery

• Hardware pack

• Double-sided tape

1PROGRAM THE PANEL

Refer to the panel programming guide as needed.

1. At a keypad, enter 6653 (PROG) to access the Programmer

Menu.

2. To enable encryption, use the two steps below and then

continue to step 3. Otherwise, go to step 3.

• Navigate to System Options. At the 1100 ENCRYPTION

prompt, select ALL to only add encrypted wireless

devices to the system. Select BOTH to allow both

encyrpted and non-encrypted wireless devices to be

programmed.

• The default passphrase appears at the

ENTER PASSPHRASE prompt. Press CMD to keep the

default. Press any select key or area to change the

passphrase and enter an 8-character hexidecimal string

(0-9, A-F).

3. In ZONE INFORMATION, enter the wireless ZONE NO: and

press CMD.

4. Enter the ZONE NAME and press CMD.

5. Select the ZONE TYPE and press CMD.

6. At the NEXT ZN? prompt, select NO.

7. Select YES when WIRELESS? displays.

8. Enter the eight-digit SERIAL# and press CMD.

9. At CONTACT, select either INTERNAL or EXTERNAL.

Note: Use consecutive zone numbers if using both internal

and external contacts.

10. If EXTERNAL was chosen in Step 9, choose NO or YES at

the NORM OPEN prompt.

11. Enter the SUPRVSN TIME and press CMD.

12. At DISARM DISABLE, select NO or YES.

13. At the NEXT ZN? prompt, select YES to ﬁnish programming

or select NO for additional programming options.

Figure 1: 1106 Housing

INSTALL THE BATTERY

Use a 3.0V lithium battery, a DMP Model CR123 battery, or an

equivalent model from Sony or Murata. For listed installations, use

either an Energizer® 123 battery or a CR123A battery manufactured

by Panasonic or Tekcell. Keep in mind, when setting up a wireless

system, program zones and connect the wireless receiver before

installing the battery.

1. Open the 1106 by inserting a 1/4” ﬂat head screwdriver in

the tab. See Figure 1.

2. Gently pull upwards on the screwdriver handle until the

housing completely opens.

3. Observe polarity and place the battery in the holder and

press it into place.

Tab

DESCRIPTION

All DMP XT Series and XR Series and

all 1100 Series Wireless Receivers.

To enable wireless encryption, the

following are required:

• Transmitters must have

ﬁrmware Version 201 or higher

• Panels must have ﬁrmware

Version 183 or higher

• Wireless receivers must have

ﬁrmware Version 300 or higher

2 1106 INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS

Mount the Transmitter

1. If mounting with screws, remove the battery. If mounting

with double-sided tape, place the tape on the back of the

transmitter.

2. Hold the transmitter in place with the magnetic reed

switch closest to where the magnet will be mounted. See

Figure 2. Ensure the transmitter and the magnet will be no

more than 1/2” (1.3cm) apart.

3. If using screws, place the supplied #4 screws into the two

mounting holes and secure the transmitter to the surface.

If using double-sided tape, place the transmitter on the

surface.

4. Snap the transmitter cover back onto the base.

Mount the Magnet

Standard Installation

1. Push the supplied magnet into the magnet cover.

2. Hold the magnet base on the door closest to the

magnetic reed switch, no more than 1/2” (1.3cm) from the

transmitter.

3. If using screws, use the provided #4 screws to mount the

base. See Figure 3. If using double-sided tape, place the

tape on the back of the base and place on the surface.

4. Snap the cover onto the base.

Commercial Installation

1. Push the supplied magnet into the magnet cover.

2. Place and hold the magnet cover directly on the door

closest to the magnetic reed switch, no more than 1/2”

(1.3cm) from the transmitter.

3. Use the provided #4 screws to mount the cover.

See Figure 4.

Note: Do not use double-sided tape for listed installations.

MOUNT THE 1106

For listed and commercial installations, use the supplied screws

when mounting the transmitter and the magnet.

Figure 3: Standard Installation

Figure 4: Commercial Installation

Wall Mount

Screw Holes

Magnetic Reed

Switch

Figure 2: Transmitter Components

3The 1106 provides a Survey LED capability to allow one person to conﬁrm communication with the

wireless receiver or panel while the cover is removed.

1. Hold the 1106 in the exact desired location.

2. Press the tamper switch to send data to the panel and determine if communication is conﬁrmed or

faulty.

Conﬁrmed: If communication is conﬁrmed, for each press or release of the tamper switch the LED

blinks immediately on and immediately o. Repeat this test to conﬁrm ﬁve separate consecutive

LED blinks. Any indication otherwise means proper communication has not been established.

Faulty: If communication is faulty, the LED remains on for about 8 seconds or ﬂashes multiple

times in quick succession. Relocate the 1106 or wireless receiver until the LED conﬁrms clear

communication.

SELECT A LOCATION

1106 INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS 3

Connect External Contacts

Refer to Contacts and Zone Information in the appropriate panel programming guide for more information. DMP

recommends using 18 or 22 AWG un-shielded wire. If you use both the magnet reed switch in the 1106 transmitter

and an external contact, use consecutive zone numbers when connecting them to the panel.

1. Remove the cover of the 1106.

2. Use a ﬂat head screwdriver to loosen the two screws on the 1106 terminal block. See Figure 5.

3. Insert the external contact wiring into the 1106 terminal block and tighten the screws.

4. Depending on how the contact was programmed in the Program the Panel section, connect the other ends

of the wires to the external contact as either normally open (N/O) or normally closed (N/C) without an end-

of-line resistor.

Figure 5: Connect External Contact

MODEL 1106

CR123

External Contact

Terminal Block

1106

Door

ADDITIONAL INFORMATION

1. Open the transmitter housing to expose the inside of the 1106. See Figure 1.

2. Remove the old battery, observe polarity, and place the new battery in the holder.

3. Snap the cover back on the 1106.

Replace the Battery

Once the battery is replaced, a sensor reset is required at the keypad to clear the LOBAT message.

1. On an LCD Keypad, press and hold 2 for two seconds. On a Graphic Touchscreen Keypad,

press RESET.

2. Enter your user code, if required. The keypad displays SENSORS OFF followed by SENSORS

ON.

Sensor Reset to Clear LOBAT

Program one

zone as an

internal contact.

EXTERNAL CONTACTS

5TEST THE 1106

After installing the 1106, perform a Wireless Check-in Test to conﬁrm the 1106 is communicating with the

panel.

At the keypad, enter 8144 (WALK) and select WLS. If the 1106 fails to check in at the keypad, relocate the

wireless device, receiver, or panel.

When this test is initiated, the panel automatically tests the communication between itself and each wireless

zone. Wireless zones should not be manually tripped during this test. Manually tripping zones during this test

could lead to a false failure.

Designed, engineered, and

manufactured in Springﬁeld, MO

using U.S. and global components.

LT-1377 1.01 23142

1106 SERIES WIRELESS

UNIVERSAL TRANSMITTER

Speciﬁcations

Battery

Life Expectancy 5 years

Type 3.0V lithium CR123A

Frequency Range 905-924 MHz

Color White

Housing Material Flame retardant ABS

Dimensions

Transmitter Case 1.79”L x 1.69”W x 0.84”H

Standard Magnet Housing 1.35”L x 0.38”W x 0.43”H

Commercial Magnet Housing 2.25”L x 0.38”W x 0.34”H

Patents

U.S. Patent No. 7,239,236

Ordering Information

1106-W Standard Wireless Universal Transmitter

Certiﬁcations

FCC Part 15 Registration ID: CCKPC0124

Industry Canada: 5251A-PC0124

ETL Listed

• ANSI/UL 1023 Household Burglar Alarm System

• ANSI/UL 634 Connections and Switches for use with

Burglar Alarm Systems Accessory

FCC Part 15 Registration ID: CCKPC0237

Industry Canada: 5251A-PC0237

Underwriters Laboratories

• ANSI/UL 1023 Household Burglar Alarm System

• ANSI/UL 634 Connections and Switches for use with

Burglar Alarm Systems Accessory

Note: For ANSI/UL 1023, install only on non-conductive

surfaces.

INTRUSION • FIRE • ACCESS • NETWORKS

2500 North Partnership Boulevard

Springﬁeld, Missouri 65803-8877

800.641.4282 | DMP.com

FCC INFORMATION

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. this device must accept any interference received, including interference that may cause undesired operation.

The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm (7.874 in.) from all

persons. It must not be located or operated in conjunction with any other antenna or transmitter.

Changes or modifications made by the user and not expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4. Consult the dealer or an experienced radio/TV technician for help.

INDUSTRY CANADA INFORMATION

This device complies with Industry Canada Licence-exempt RSS standards. Operation is subject to the following two

conditions:

1. This device may not cause interference, and

2. this device must accept any interference, including interference that may cause undesired operation of the device.

This system has been evaluated for RF Exposure per RSS-102 and is in compliance with the limits specified by Health Canada

Safety Code 6. The system must be installed at a minimum separation distance from the antenna to a general bystander of 7.87

inches (20 cm) to maintain compliance with the General Population limits.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation

est autorisée aux deux conditions suivantes:

1. l’appareil ne doit pas produire de brouillage, et

2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en

compromettre le fonctionnement.

L’exposition aux radiofréquences de ce système a été évaluée selon la norme RSS-102 et est jugée conforme aux limites établies

par le Code de sécurité 6 de Santé Canada. Le système doit être installé à une distance minimale de 7.87 pouces (20 cm)

séparant l’antenne d’une personne présente en conformité avec les limites permises d’exposition du grand public.

Digital Monitoring Products 1106 Universal Transmitter Guide d'installation

Marque: Digital Monitoring Products

Modèle: 1106 Universal Transmitter

Catégorie: Lecteurs de contrôle d'accès

Taper: Guide d'installation

Ce manuel convient également à

1106

Télécharger le PDF

rapport

dans d''autres langues

English: Digital Monitoring Products 1106 Universal Transmitter Installation guide

Digital Monitoring Products 1106 Universal Transmitter Guide d'installation

Ce manuel convient également à

Digital Monitoring Products 1106 Universal Transmitter Guide d'installation

dans d''autres langues

Documents connexes

Autres documents