Briggs & Stratton 030547-01 Manuel utilisateur

Not for

Reproduction

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

MILWAUKEE, WISCONSIN, U.S.A.

Portable Generator

Operator’s Manual

Manual No. 80008171 Revision B

This generator is certified in accordance with CSA (Canadian Standards Association) standard C22.2 No.

100-04 (motors and generators) and rated in accordance with PGMA (Portable Generator Manufacturers’

Association) standard PGMA G200 (Standard for Testing and Validating Performance of Portable Generators).

Not for

Reproduction

2 BRIGGSandSTRATTON.COM

BRIGGS & STRATTON POWER PRODUCTS is a registered

trademark of Briggs & Stratton Corporation

Milwaukee, WI, USA

Thank you for purchasing this quality-built Briggs & Stratton® generator. We are pleased that you’ve placed your

confidence in the Briggs & Stratton brand. When operated and maintained according to the instructions in this

manual, your Briggs & Stratton generator will provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with generator

products and how to avoid them. This generator is designed and intended only for supplying electrical power

for operating compatible electrical lighting, appliances, tools and motor loads, and is not intended for any other

purpose. It is important that you read and understand these instructions thoroughly before attempting to start or

operate this equipment. Save this original manual for future reference.

This generator requires final assembly before use. Refer to the Assembly section of this manual for

instructions on final assembly procedures. Follow the instructions completely.

Where to Find Us

You never have to look far to find Briggs & Stratton support and service for your generator. Consult your Yellow

Pages. There are over 30,000 Briggs & Stratton authorized service dealers worldwide who provide quality service.

You can also contact Briggs & Stratton Customer Service by phone at (800) 743-4115, or on the Internet at

BRIGGSandSTRATTON.COM.

Generator Engine

Model Number _____________________ Model Number ______________________

Revision __________________________ Type Number _______________________

Serial Number ______________________ Code Number _______________________

Date Purchased ___________________

Table of Contents

Safe Operation Checklist ............... 3

Operator Safety....................... 4

Assembly............................ 9

Features and Controls ................ 15

Operation........................... 17

Maintenance ........................ 20

Troubleshooting ..................... 25

Warranty ........................... 27

Product Specifications ................ 28

Common Service Parts ............... 28

Not for

Reproduction

3

Safe Operation Checklist

Safe operation of the portable generator requires the completion of the following tasks:

Carbon Monoxide (CO) Alarm

Carbon monoxide (CO) alarm(s) in working order.

Smoke Alarm

Smoke alarm(s) in working order.

Generator Location

Generator placed in a Carbon Monoxide (CO) safe zone. See Generator Location to reduce the Risk of

Carbon Monoxide Poisoning.

Generator placed in a fire safe zone. See Generator Location to reduce the Risk of Fire.

Generator located on flat and level surface.

Oil and Fuel

Engine filled to proper oil level. See Add Engine Oil.

Fuel tank filled at or below baffle. See Add Fuel.

Inspect fuel lines, tank, cap and fittings each time before using generator. DO NOT use if fuel leak or damage

is found.

Electrical

When connecting to a buildings electrical system install listed transfer equipment. See Connecting to a

Building’s Electrical System.

Electrical cords are rated for intended loads. See Cord Sets and Receptacles.

Electrical cords do not run through doorways, windows, holes in ceilings, walls or floors.

Inspect electrical cords thoroughly before each use. DO NOT use if damaged.

All labeled electrical cord safeties are understood and being followed.

Operation

Start engine. See Starting the Engine.

Not for

Reproduction

4 BRIGGSandSTRATTON.COM

Operator Safety

Safety Labels

The generator safety labels shown below and on the next page are placed on your portable generator to draw

attention to potential safety hazards.

202997

Not for

Reproduction

5

WARNING

AVERTISSEMENT

312728

Not for

Reproduction

Equipment Description

Read this manual carefully and become

familiar with your generator. Know its

applications, its limitations and any hazards

involved.

The generator is an engine–driven, revolving field,

alternating current (AC) generator. It was designed

to supply electrical power for operating compatible

electrical lighting, appliances, tools and motor loads.

The generator’s revolving field is driven at about

3,600 rpm by a single-cylinder engine.

NOTICE

Exceeding generators wattage/amperage

capacity could damage generator and/or electrical

devices connected to it.

• DO NOT exceed the generator’s wattage/amperage

capacity. See Don’t Overload Generator in the Operation

section.

Every effort has been made to ensure that the

information in this manual is both accurate and current.

However, the manufacturer reserves the right to

change, alter or otherwise improve the generator and

this documentation at any time without prior notice.

The Emission Control System for this generator is

warranted for standards set by the Environmental

Protection Agency and the California Air Resources

Board.

This spark ignition system complies with the Canadian

standard ICES-002.

Important Safety Information

The manufacturer cannot possibly anticipate every

possible circumstance that might involve a hazard.

The warnings in this manual, and the tags and decals

affixed to the unit are, therefore, not all-inclusive.

If you use a procedure, work method or operating

technique that the manufacturer does not specifically

recommend, you must satisfy yourself that it is safe

for you and others. You must also make sure that the

procedure, work method or operating technique that

you choose does not render the generator unsafe.

Safety Symbols and Meanings

The safety alert symbol indicates a potential

personal injury hazard. A signal word (DANGER,

WARNING, or CAUTION) is used with the alert symbol

to designate a degree or level of hazard seriousness.

A safety symbol may be used to represent the type of

hazard. The signal word NOTICE is used to address

practices not related to personal injury.

DANGER indicates a hazard which, if not avoided,

will result in death or serious injury.

WARNING indicates a hazard which, if not

avoided, could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided,

could result in minor or moderate injury.

NOTICE address practices not related to personal

injury.

6 BRIGGSandSTRATTON.COM

Fire

Explosion

Toxic Fumes

Hot Surface

Moving Parts

Electrical Shock

Kickback

Flying Objects

Operator’s Manual

WARNING The engine exhaust from this

product contains chemicals known to the State of

California to cause cancer, birth defects, or other

reproductive harm.

WARNING Certain components in this product

and related accessories contain chemicals known to

the State of California to cause cancer, birth defects

or other reproductive harm. Wash hands after

handling.

Not for

Reproduction

7

WARNING

• This generator does not meet U. S. Coast Guard

Regulation 33CFR-183 and should not be used on

marine applications.

• Failure to use the appropriate U. S. Coast Guard

approved generator could result in death or serious injury.

WARNING Fuel and its vapors are extremely

flammable and explosive which

could cause burns, fire or explosion

resulting in death or serious injury.

WHEN ADDING OR DRAINING FUEL

• Turn generator engine OFF and let it cool at least 2

minutes before removing fuel cap. Loosen cap slowly to

relieve pressure in tank.

• Fill or drain fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

• Check fuel lines, tank, cap and fittings frequently for

cracks or leaks. Replace if necessary.

• DO NOT light a cigarette or smoke.

WHEN STARTING EQUIPMENT

• Ensure spark plug, muffler, fuel cap, and air cleaner are

in place.

• DO NOT crank engine with spark plug removed.

WHEN OPERATING EQUIPMENT

• DO NOT operate this product inside any building,

carport, porch, mobile equipment, marine applications, or

enclosure.

• DO NOT tip engine or equipment at angle which causes

fuel to spill.

• DO NOT stop engine by moving choke control to

CHOKE (

) position.

WHEN TRANSPORTING, MOVING OR REPAIRING

EQUIPMENT

• Transport/move/repair with fuel tank EMPTY or with fuel

shutoff valve OFF (0).

• DO NOT tip engine or equipment at angle which causes

fuel to spill.

• Disconnect spark plug wire.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN

TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers, or other appliances that have pilot light or other

ignition source because they could ignite fuel vapors.

WARNING Starter cord kickback (rapid

retraction) will pull hand and arm toward

engine faster than you can let go which

could cause broken bones, fractures,

bruises, or sprains resulting in serious injury.

• When starting engine, pull cord slowly until resistance is

felt and then pull rapidly to avoid kickback.

• NEVER start or stop engine with electrical devices

plugged in and turned on.

WARNING POISONOUS GAS HAZARD.

Engine exhaust contains carbon monoxide,

a poisonous gas that could kill you in

minutes. You CANNOT smell it, see it, or

taste it. Even if you do not smell exhaust fumes, you

could still be exposed to carbon monoxide gas.

• Operate this product ONLY outside far away from

windows, doors and vents to reduce the risk of carbon

monoxide gas from accumulating and potentially being

drawn towards occupied spaces.

• Install battery-operated carbon monoxide alarms or

plug-in carbon monoxide alarms with battery back-up

according to the manufacturer’s instructions. Smoke

alarms cannot detect carbon monoxide gas.

• DO NOT run this product inside homes, garages,

basements, crawlspaces, sheds, or other partially-

enclosed spaces even if using fans or opening doors

and windows for ventilation. Carbon monoxide can

quickly build up in these spaces and can linger for hours,

even after this product has shut off.

• ALWAYS place this product downwind and point the

engine exhaust away from occupied spaces.

If you start to feel sick, dizzy, or weak while using this

product, get to fresh air RIGHT AWAY. See a doctor. You

may have carbon monoxide poisoning.

Not for

Reproduction

NOTICE

Exceeding generators wattage/amperage

capacity could damage generator and/or electrical

devices connected to it.

• DO NOT exceed the generator’s wattage/amperage

capacity. See Don’t Overload Generator in the Operation

section.

• Start generator and let engine stabilize before connecting

electrical loads.

• Connect electrical loads in OFF position, then turn ON for

operation.

• Turn electrical loads OFF and disconnect from generator

before stopping generator.

NOTICE

Improper treatment of generator could

damage it and shorten its life.

• Use generator only for intended uses.

• If you have questions about intended use, ask dealer or

contact local service center.

• Operate generator only on level surfaces.

• DO NOT expose generator to excessive moisture, dust,

dirt, or corrosive vapors.

• DO NOT insert any objects through cooling slots.

• If connected devices overheat, turn them off and

disconnect them from generator.

• Shut off generator if:

-electrical output is lost;

-equipment sparks, smokes, or emits flames;

-unit vibrates excessively.

8 BRIGGSandSTRATTON.COM

CAUTION Excessively high operating speeds

could result in minor injury.

Excessively low operating speeds impose a heavy

load.

• DO NOT tamper with governor spring, links or other parts

to increase engine speed. Generator supplies correct

rated frequency and voltage when running at governed

speed.

• DO NOT modify generator in any way.

WARNING Starter and other rotating parts

could entangle hands, hair, clothing, or

accessories resulting in serious injury.

• NEVER operate generator without protective housing or

covers.

• DO NOT wear loose clothing, jewelry or anything that

could be caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.

WARNING

Generator voltage could cause

electrical shock or burn resulting in death or

serious injury.

• Use listed transfer equipment, suitable for the intended

use, to prevent backfeed by isolating generator from

electric utility workers.

• When using generator for backup power, notify utility

company.

• Use a ground fault circuit interrupter (GFCI) in any damp

or highly conductive area, such as metal decking or steel

work.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are

worn, frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain or wet weather.

• DO NOT handle generator or electrical cords while

standing in water, while barefoot, or while hands or feet

are wet.

• DO NOT allow unqualified persons or children to operate

or service generator.

WARNING Exhaust heat/gases could ignite

combustibles, structures or damage

fuel tank causing a fire, resulting in

death or serious injury.

Contact with muffler area could cause burns

resulting in serious injury.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 ft. (1.5 m) of clearance on all sides of

generator including overhead.

• It is a violation of California Public Resource Code,

Section 4442, to use or operate the engine on any forest-

covered, brush-covered, or grass-covered land unless

the exhaust system is equipped with a spark arrester, as

defined in Section 4442, maintained in effective working

order. Other states or federal jurisdictions may have

similar laws.

Contact the original equipment manufacturer, retailer,

or dealer to obtain a spark arrester designed for the

exhaust system installed on this engine.

• Replacement parts must be the same and installed in the

same position as the original parts.

WARNING Unintentional sparking could cause

fire or electric shock resulting in

death or serious injury.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

GENERATOR

• Disconnect the spark plug wire from the spark plug and

place the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

Not for

Reproduction

Assembly

Your generator requires some assembly and is ready

for use after it has been properly serviced with the

recommended oil and fuel.

If you have any problems with the assembly of your

generator, please call the generator helpline at

1-800-743-4115. If calling for assistance, please

have the model, revision, and serial number from the

identification label available. See Features and Controls

for identification label location.

Unpack Generator

1. Set the carton on a rigid, flat surface.

2. Remove everything from carton except generator.

3. Open carton completely by cutting each corner

from top to bottom.

4. Leave generator on carton to install wheel kit.

Shipment Contents

The generator is supplied with:

• Engine oil bottle

• Operator’s manual

• Wheel kit

Install Wheel Kit

NOTICE Wheel kit is not intended for over-the-road

use.

You will need the following tools to install these

components:

• 13 mm wrench

• Socket wrench with 13 mm socket

Install the wheel kit as follows:

1. Tip generator so that engine side is down.

2. Slide axle stud (A) through wheel (B).

NOTICE Be sure to install wheel with raised hub

inboard.

3. Slide a spacer (C) over axle stud on back side of

wheel.

4. Slide axle stud through mounting bracket.

5. Insert retaining pin (D) through hole on axle stud.

6. Repeat steps 2 through 5 to secure second wheel.

7. Line up holes in support leg (E) with holes in

generator frame.

8. Attach support leg using two 16 mm capscrews

(F) and two M8 hex nuts (G). Tighten with a

13 mm socket wrench and 13 mm wrench.

9. Return generator to normal operating position

(resting on wheels).

10. Slide handle bracket over generator frame and

attach handle (H) using two 50 mm capscrews (J)

and two M8 hex nuts (K). Tighten with a 13 mm

socket wrench and 13 mm wrench.

9

D

B

C

A

F

G

E

J

K

H

Not for

Reproduction

Add Engine Oil

1. Place generator on a flat, level surface.

2. Clean area around oil fill and remove yellow oil fill

cap.

3. Using oil funnel (optional), slowly pour contents of

provided oil bottle into oil fill opening.

NOTICE

Improper treatment of generator could

damage it and shorten its life.

• DO NOT attempt to crank or start the engine before it has

been properly serviced with the recommended oil. This

could result in an engine failure.

4. Replace oil fill cap and fully tighten.

Add Fuel

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). For

high altitude use, see High Altitude.

• Gasoline with up to 10% ethanol (gasohol) is

acceptable.

NOTICE Use of unapproved fuels could damage

generator and voids warranty.

• DO NOT use unapproved gasoline such as E15 and E85.

• DO NOT mix oil in gasoline or modify engine to run on

alternate fuels.

To protect the fuel system from gum formation, mix

in a fuel stabilizer when adding fuel. See Storage.

All fuel is not the same. If you experience starting or

performance problems after using fuel, switch to a

different fuel provider or change brands. This engine is

certified to operate on gasoline. The emission control

system for this engine is EM (Engine Modifications).

1. Clean area around fuel fill cap, remove cap.

2. Slowly add unleaded gasoline (A) to fuel tank

(B). Be careful not to fill above the baffle (C).

This allows adequate space for fuel expansion as

shown.

3. Install fuel cap and let any spilled fuel evaporate

before starting engine.

High Altitude

At altitudes over 5,000 ft. (1524 m), a minimum

85 octane / 85 AKI (89 RON) gasoline is acceptable.

To remain emissions compliant, high altitude

adjustment is required. Operation without this

adjustment will cause decreased performance,

increased fuel consumption, and increased emissions.

See an authorized dealer for high altitude adjustment

information. Operation of the engine at altitudes

below 2,500 ft. (762 m) with the high altitude kit is not

recommended.

10 BRIGGSandSTRATTON.COM

FUEL

TANK

C

B

A

WARNING Fuel and its vapors are extremely

flammable and explosive which could

cause burns, fire or explosion

resulting in death or serious injury.

WHEN ADDING FUEL

• Turn generator engine OFF and let it cool at least 2

minutes before removing fuel cap. Loosen cap slowly to

relieve pressure in tank.

• Fill fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

• Check fuel lines, tank, cap and fittings frequently for

cracks or leaks. Replace if necessary.

• DO NOT light a cigarette or smoke.

Not for

Reproduction

11

System Ground

The generator has a system ground that connects the

generator frame components to the ground terminals

on the AC output receptacles. The system ground is

connected to the AC neutral wire (the neutral is bonded

to the generator frame).

Special Requirements

There may be Federal or State Occupational Safety

and Health Administration (OSHA) regulations, local

codes, or ordinances that apply to the intended use of

the generator. Please consult a qualified electrician,

electrical inspector, or the local agency having

jurisdiction:

• In some areas, generators are required to be

registered with local utility companies.

• If the generator is used at a construction site,

there may be additional regulations which must

be observed.

Connecting to a Building’s Electrical

System

Connections for standby power to a building’s

electrical system must use a listed transfer switch

installed by a current licensed electrician. The

connection must isolate the generator power from the

utility power and must comply with all applicable laws

and electrical codes.

WARNING

Generator voltage could cause

electrical shock or burn resulting in death or

serious injury.

• Use listed transfer equipment, suitable for the intended

use, to prevent backfeed by isolating generator from

electric utility workers.

• When using generator for backup power, notify utility

company.

• Use a ground fault circuit interrupter (GFCI) in any damp

or highly conductive area, such as metal decking or steel

work.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are

worn, frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain or wet weather.

• DO NOT handle generator or electrical cords while

standing in water, while barefoot, or while hands or feet

are wet.

• DO NOT allow unqualified persons or children to operate

or service generator.

Not for

Reproduction

Portable Generator Location

Before starting the portable generator there are two

equally important safety concerns regarding carbon

monoxide (CO) poisoning and fire that must be

addressed.

NOTICE Satisfying the RISK OF CARBON

MONOXIDE POISONING location requirements may

not satisfy the fire location requirements. Satisfying the

RISK OF FIRE location requirements may not satisfy

the CARBON MONOXIDE POISONING location

requirements.

Operation Location of Portable Generator to

REDUCE THE RISK OF CARBON MONOXIDE

POISONING

All fossil fuel burning equipment, such as a portable

generator, contains carbon monoxide (CO) gas in the

engine exhaust, a poisonous gas that could kill you in

minutes. You CANNOT smell it, see it, or taste it. Even

if you do not smell exhaust fumes, you could still be

exposed to carbon monoxide gas. The following must

be completed prior to starting the portable generator

engine:

• By law it is required in many states to have a

Carbon Monoxide (CO) alarm (A) in operating

condition in your home. Install/maintain battery-

operated carbon monoxide alarms or plug-in

carbon monoxide alarms with battery back-up

according to the manufacturer’s instructions. A

CO alarm is an electronic device that detects

hazardous levels of CO. When there is a buildup

of CO, the alarm will alert the occupants by

flashing visual indicator light and alarm. Smoke

alarms cannot detect CO gas.

• Operate this product ONLY outside far away from

windows, doors and vents to reduce the risk of

carbon monoxide gas from accumulating and

potentially being drawn towards occupied spaces.

• DO NOT run this product inside homes, garages,

basements, crawlspaces, sheds, or other partially-

enclosed spaces even if using fans or opening

doors and windows for ventilation. Carbon

monoxide can quickly build up in these spaces

and can linger for hours, even after this product

has shut off.

• Your neighbor(s) home may be exposed to the

engine exhaust from your portable generator and

must be considered when deciding on a location

for the safe operation of your portable generator.

• ALWAYS place this product downwind and point

the engine exhaust away from occupied spaces.

If you start to feel sick, dizzy, or weak while using this

product, get to fresh air RIGHT AWAY. See a doctor.

You may have carbon monoxide poisoning.

A

12 BRIGGSandSTRATTON.COM

Not for

Reproduction

13

EXAMPLE OF LOCATION TO REDUCE THE RISK OF CARBON MONOXIDE

POISONING

DO NOT OPERATE IN ANY OF THE FOLLOWING LOCATIONS

Only use OUTSIDE

and FAR AWAY from

windows, doors and vents.

Direct exhaust AWAY

from windows, doors,

and vents.

KEEP

FAR AWAY

CO Alarm

in Living Areas

E

X

H

A

U

S

T

(

C

O

)

Generator too

close to home

and exhaust

directed towards

windows, doors

and vents.

Garage

Attic

Living Area

Basement

Crawlspace

E

X

H

A

U

S

T

(

C

O

)

Entryway,

Porch

Not for

Reproduction

Operation Location of Portable Generator to

REDUCE THE RISK OF FIRE

EXAMPLE OF LOCATION TO REDUCE THE RISK OF FIRE

WARNING Exhaust heat/gases could ignite

combustibles, structures or damage fuel

tank causing a fire, resulting in death or

serious injury.

• Portable generator must be at least 5 ft. (1.5 m) from

any structure, overhang, trees, windows, doors, any wall

opening, shrubs, or vegetation over 12 inches (30.5 cm)

in height.

• DO NOT place portable generator under a deck or other

type of structure that may confine airflow.

• Smoke alarm(s) MUST be installed and maintained

indoors according to the manufacturer’s instructions/

recommendations. Carbon monoxide alarms cannot

detect smoke.

• DO NOT place portable generator in manner other than

shown.

Direct exhaust AWAY from

windows, doors, and vents.

E

X

H

A

U

S

T

(

C

O

)

5 ft. (1.5 m) min.

14 BRIGGSandSTRATTON.COM

Not for

Reproduction

Features and Controls

Read this Operator’s Manual and safety rules before operating your generator.

Compare the illustrations with your generator, to familiarize yourself with the locations of various controls

and adjustments. Save this manual for future reference.

A - Rocker Switch — Set this switch to ON (I) before

using recoil starter. Set switch to OFF (0) to switch

off engine.

B - 120 Volt AC, 30 Amp Travel Trailer Receptacle

— May be used to supply electrical power for the

operation of 120 Volt AC, 30 Amp, single phase,

60 Hz electrical, travel trailer loads.

C - Circuit Breakers — Push-to-reset circuit breakers

are provided to protect the generator against

electrical overload.

D - 120 Volt AC, 20 Amp, Duplex Receptacle —

May be used to supply electrical power for the

operation of 120 Volt AC, 20 Amp, single phase,

60 Hz electrical, lighting, appliance, tool and motor

loads.

E - Oil Fill Cap — Check and add engine oil here.

F - Oil Drain Plug — Drain engine oil here.

G - Grounding Fastener — Consult your local agency

having jurisdiction for grounding requirements in

your area.

H - Spark Arrester Muffler — Exhaust muffler lowers

engine noise and is equipped with a spark arrester

screen.

J - Recoil Starter — Used to start the engine

manually.

K - Air Cleaner — Protects engine by filtering dust

and debris out of intake air.

L - Choke Lever — Used when starting a cold engine.

M - Fuel Valve — Used to turn fuel supply on and off to

engine.

N - Fuel Tank — Capacity of four (4) U.S. gallons

(15.14 l).

Items Not Shown:

Engine Identification — Provides model, type and

code of engine. Please have these readily available if

calling for assistance.

Identification Label — Provides model and serial

number of generator. Please have these readily

available if calling for assistance.

N

A

B

C

F

K

M

J

L

H

D

E

G

15

Not for

Reproduction

Cord Sets and Receptacles

Use only high quality, well-insulated, grounded

extension cords with the generator’s receptacles.

Inspect extension cords before each use.

Check the ratings of all extension cords before you

use them. Check operator’s manuals of devices to be

powered for the manufacturer’s recommendations.

120 Volt AC, 30 Amp Travel Trailer Receptacle

Use a NEMA TT–30 plug with this receptacle. Connect

a 3–wire travel trailer cord set rated for 125 Volt AC

loads at 30 Amps to the plug.

Use this receptacle to operate 120 Volt AC, 60 Hz,

single phase travel trailer loads requiring up to

3,500 watts (3.5 kW) of power at 29.16 Amps. The

outlet is protected by a push-to-reset circuit breaker.

NOTICE

Receptacles may be marked with rating

value greater than generator output capacity.

• NEVER attempt to power a device requiring more

amperage than generator or receptacle can supply.

• DO NOT overload the generator. See Don’t Overload

Generator.

120 Volt AC, 20 Amp, Duplex Receptacle

The duplex receptacle is protected against overload by

a push-to-reset circuit breaker.

Use receptacle to operate 120 Volt AC, single-phase,

60 Hz electrical loads requiring up to 2,400 watts

(2.4 kW) at 20 Amps of current. Use cord sets that are

rated for 125 Volt AC loads at 20 Amps (or greater).

WARNING Damaged or overloaded electrical

cords could overheat, arc, and burn

resulting in death or serious injury.

• ONLY use cords rated for your loads.

• Follow all safeties on electrical cords.

• Inspect cord sets before each use.

Hot

120V

Ground (Green)

NEMA TT-30

Neutral

16 BRIGGSandSTRATTON.COM

Not for

Reproduction

Operation

Starting the Engine

Disconnect all electrical loads from the generator. Use

the following start instructions:

1. Make sure unit is on a level surface.

NOTICE Failure to start and operate the unit on a

level surface could cause the unit not to start or shut

down during operation.

2. Turn the fuel valve (A) to the ON (I) position.

3. Push choke lever (B) to CHOKE ( ) position.

4. Push rocker switch (C) to ON (I) position.

5. Grasp recoil handle and pull slowly until slight

resistance is felt. Then pull rapidly one time only

to start engine.

• If engine starts, proceed to step 7.

• If engine fails to start, proceed to step 6.

6. Move choke lever to HALF choke position, and

pull recoil handle twice.

• If engine fails to start, repeat steps 5 thru 7.

7. Slowly move choke lever to RUN (

) position. If

engine falters, move choke lever to HALF choke

position until engine runs smoothly, and then to

RUN ( ) position.

NOTICE If engine floods, place choke lever in

RUN ( ) position and crank until engine starts.

NOTICE If engine starts after 3 pulls but fails to run,

or if unit shuts down during operation, make sure unit

is on a level surface and check for proper oil level in

crankcase. This unit may be equipped with a low oil

protection device. If so, oil must be at proper level for

engine to start.

A

B

C

WARNING Starter cord kickback (rapid

retraction) will pull hand and arm toward

engine faster than you can let go which

could cause broken bones, fractures,

bruises, or sprains resulting in serious injury.

• When starting engine, pull cord slowly until resistance is

felt and then pull rapidly to avoid kickback.

• NEVER start or stop engine with electrical devices

plugged in and turned on.

WARNING Exhaust heat/gases could ignite

combustibles, structures or damage

fuel tank causing a fire, resulting in

death or serious injury.

Contact with muffler area could cause burns

resulting in serious injury.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 ft. (1.5 m) of clearance on all sides of

generator including overhead.

• It is a violation of California Public Resource Code,

Section 4442, to use or operate the engine on any forest-

covered, brush-covered, or grass-covered land unless

the exhaust system is equipped with a spark arrester, as

defined in Section 4442, maintained in effective working

order. Other states or federal jurisdictions may have

similar laws.

Contact the original equipment manufacturer, retailer,

or dealer to obtain a spark arrester designed for the

exhaust system installed on this engine.

• Replacement parts must be the same and installed in the

same position as the original parts.

17

Not for

Reproduction

Connecting Electrical Loads

1. Let engine stabilize and warm up for a few

minutes after starting.

2. Plug in and turn on the desired 120 Volt AC,

single phase, 60 Hz electrical loads.

NOTICE

• DO NOT connect 240 Volt loads to the 120 Volt

receptacles.

• DO NOT connect 3-phase loads to the generator.

• DO NOT connect 50 Hz loads to the generator.

• DO NOT OVERLOAD THE GENERATOR. See

Don’t Overload Generator.

NOTICE Exceeding generators wattage/amperage

capacity could damage generator and/or electrical

devices connected to it.

• DO NOT exceed the generator’s wattage/amperage

capacity. See Don’t Overload Generator in the Operation

section.

• Start generator and let engine stabilize before connecting

electrical loads.

• Connect electrical loads in OFF position, then turn ON for

operation.

• Turn electrical loads OFF and disconnect from generator

before stopping generator.

Stopping the Engine

1. Turn OFF and unplug all electrical loads from

generator panel receptacles. NEVER start or stop

engine with electrical devices plugged in and

turned ON.

2. Let engine run at no-load for several minutes

to stabilize internal temperatures of engine and

generator.

3. Push rocker switch to OFF (0) position.

4. Move fuel valve to OFF (0) position.

WARNING Fuel and its vapors are extremely

flammable and explosive which

could cause burns, fire or explosion

resulting in death or serious injury.

• DO NOT stop engine by moving choke control to

CHOKE (

) position.

18 BRIGGSandSTRATTON.COM

Not for

Reproduction

Don’t Overload Generator

Capacity

You must make sure your generator can supply

enough rated (running) and surge (starting) watts for

the items you will power at the same time. Follow these

simple steps:

1. Select the items you will power at the same time.

2. Total the rated (running) watts of these items.

This is the amount of power your generator must

produce to keep your items running. See the table

on the right.

3. Estimate how many surge (starting) watts you will

need. Surge wattage is the short burst of power

needed to start electric motor-driven tools or

appliances such as a circular saw or refrigerator.

Because not all motors start at the same time, total

surge watts can be estimated by adding only the

item(s) with the highest additional surge watts to

the total rated watts from step 2.

Example:

Total Rated (Running) Watts = 3275

Highest Additional Surge Watts = 2350

Total Generator Output Required = 5625

Power Management

To prolong the life of your generator and attached

devices, it is important to take care when adding

electrical loads to your generator. There should be

nothing connected to the generator outlets before

starting its engine. The correct and safe way to

manage generator power is to sequentially add loads

as follows:

1. With nothing connected to the generator, start the

engine as described in this manual.

2. Plug in and turn on the first load, preferably the

largest load you have.

3. Permit the generator output to stabilize (engine

runs smoothly and attached device operates

properly).

4. Plug in and turn on the next load.

5. Again, permit the generator to stabilize.

6. Repeat steps 4 and 5 for each additional load.

NEVER add more loads than the generator capacity.

Take special care to consider surge loads in generator

capacity, as described above.

* Wattages listed are approximate only. Check tool or

appliance for actual wattage.

Tool or

Appliance

Running

(Rated) Watts

Additional

Starting (Surge)

Watts

Water Well

Pump

1200 2100

Refrigerator 700 2200

Furnace Fan 800 2350

Television 500 —

Light (75 Watts) 75 —

3275 Total

Running Watts

2350 Highest

Starting Watts

Wattage Reference Guide

Tool or Appliance

Running*

(Rated)

Watts

Additional

Starting

(Surge)

Watts

Essentials

Light Bulb - 75 watt 75 —

Furnace Fan Blower - 1/2 HP 800 2350

Sump Pump - 1/3 HP 800 1300

Refrigerator/Freezer 700 2200

Water Well Pump - 1/2 HP 1000 2100

Heating/Cooling

Window AC - 10,000 BTU 1200 3600

Humidifier - 13 Gal 175 —

Central AC - 24,000 BTU 3800 11400

Kitchen

Microwave Oven - 1000 Watt 1000 —

Coffee Maker 1000 —

Electric Stove - 8” Element 2100 —

Toaster 850 —

Family Room

DVD/CD Player 100 —

VCR 100 —

Stereo Receiver 450 —

Color Television - 27 in 500 —

Personal Computer w/17 in

monitor

800 —

Other

Security System 500 —

AM/FM Clock Radio 100 —

Garage Door Opener - 1/2 HP 875 2350

Electric Water Heater 4700 11700

DIY/Job Site

Quartz Halogen Work Light 1000 —

Airless Sprayer - 1/3 HP 600 1200

Reciprocating Saw 960 —

Electric Drill - 1/2 HP, 5.4

Amps

600 900

Circular Saw - 7-1/4 in 1400 2300

Miter Saw - 10 in 1800 1800

Table Planer - 6 in 1800 1800

Table Saw/Radial Arm Saw -

10 in

2000 2000

Air Compressor - 1 HP 1600 4500

19

Not for

Reproduction

Maintenance

Maintenance Schedule

Follow the hourly or calendar intervals, whichever

occurs first. More frequent service is required when

operating in adverse conditions noted below.

1

Service more often under dirty or dusty conditions.

General Recommendations

Regular maintenance will improve the performance

and extend the life of the generator. See any

authorized dealer for service.

The generator’s warranty does not cover items that

have been subjected to operator abuse or negligence.

To receive full value from the warranty, the operator

must maintain the generator as instructed in this

manual.

Some adjustments will need to be made periodically to

properly maintain your generator.

All service and adjustments should be made at least

once each season. New spark plugs and clean air filter

assure proper fuel-air mixture and help your engine run

better and last longer. Follow the requirements in the

Maintenance Schedule chart above.

Emissions Control

Maintenance, replacement, or repair of the

emissions control devices and systems may

be performed by any non-road engine repair

establishment or individual. However, to obtain

”no charge” emissions control service, the work must

be performed by a factory authorized dealer. See the

Emissions Warranty.

Generator Maintenance

Generator maintenance consists of keeping the unit

clean and dry. Operate and store the unit in a clean dry

environment where it will not be exposed to excessive

dust, dirt, moisture, or any corrosive vapors. Cooling

air slots in the generator must not become clogged

with snow, leaves, or any other foreign material.

NOTICE DO NOT use water or other liquids to clean

generator. Liquids can enter engine fuel system,

causing poor performance and/or failure to occur. In

addition, if liquid enters generator through cooling air

slots, some of the liquid will be retained in voids and

cracks of the rotor and stator winding insulation. Liquid

and dirt buildup on the generator internal windings will

eventually decrease the insulation resistance of these

windings.

Cleaning

Daily or before use, look around and underneath

the generator for signs of oil or fuel leaks. Clean

accumulated debris from inside and outside the

generator. Keep the linkage, spring and other engine

controls clean. Keep the area around and behind

the muffler free from any combustible debris. Inspect

cooling air slots and openings on generator. These

openings must be kept clean and unobstructed.

Engine parts should be kept clean to reduce the risk of

overheating and ignition of accumulated debris:

• Use a damp cloth to wipe exterior surfaces clean.

NOTICE

Improper treatment of generator could

damage it and shorten its life.

• DO NOT expose generator to excessive moisture, dust,

dirt, or corrosive vapors.

• DO NOT insert any objects through cooling slots.

• Use a soft bristle brush to loosen caked on dirt or

oil.

• Use a vacuum cleaner to pick up loose dirt and

debris.

First 5 Hours

• Change engine oil

Every 8 Hours or Daily

• Clean debris

• Check engine oil level

Every 25 Hours or Yearly

• Service engine air cleaner

1

Every 50 Hours or Yearly

• Change engine oil

1

Every 100 Hours or Yearly

• Service fuel valve

• Service spark plug

• Inspect muffler and spark arrester

• Clean cooling system

1

20 BRIGGSandSTRATTON.COM

La page charge ...

Briggs & Stratton 030547-01 Manuel utilisateur

Ce manuel convient également à

Briggs & Stratton 030547-01 Manuel utilisateur

dans d''autres langues

Autres documents