Samsung NY36R9966PM/AA Manuel utilisateur

Dual Fuel Pro Range

Installation manual

NY36R9966P*

Install_NY9900R_CHEF_NY36R9966PS_AA_DG68-01106B-01_EN+MES+CFR.indb 1 2019-03-14  3:55:49

2 English

ANTITIP DEVICE

WARNING

ALL RANGES CAN TIP, RESULTING IN PERSONAL INJURY.

TIPPING RANGES CAN CAUSE BURNS FROM SPILLS,

PERSONAL INJURY, AND/OR DEATH.

INSTALL AND CHECK THE ANTI-TIP BRACKET FOLLOWING

THE INSTRUCTIONS AND TEMPLATE SUPPLIED WITH THE

BRACKET.

• To prevent accidental tipping of the range, attach an approved

anti-tip device to the oor. (See Installing the Anti-Tip Device

in the Installation Instructions.) Check for proper installation by

carefully tipping the range forward. The anti-tip device should

engage and prevent the range from tipping over.

• If the range is pulled out away from the wall for any reason,

make sure the anti-tip device is reengaged after the range has

been pushed back into place.

• Follow the installation instructions found in the Installation

Manual. Failure to follow these instructions can result in death,

serious personal injury, and / or property damage.

• DO NOT step / sit / lean on the door or drawer to prevent

accidental tipping of the range.

WARNING: If the information in this manual is not followed exactly,

a re or explosion may result causing property damage, personal

injury or death.

• DO NOT store or use gasoline or other ammable vapors and

liquids in the vicinity of this or any other appliance.

• WHAT TO DO IF YOU SMELL GAS:

- DO NOT try to light any appliance.

- DO NOT touch any electrical switch.

- DO NOT use any phone in your building.

- Immediately call your gas supplier from a neighbor’s phone.

Follow the gas supplier’s instructions.

- If you cannot reach your gas supplier, call the re

department.

• Installation and service must be performed by a qualied

installer, service agency, or the gas supplier.

Install_NY9900R_CHEF_NY36R9966PS_AA_DG68-01106B-01_EN+MES+CFR.indb 2 2019-03-14  3:55:49

English 3

Contents

Before you begin 4

About this manual 4

Important safety information 4

Read all instructions before using this appliance 4

Symbols used in this manual 4

California Proposition 65 Warning 5

Commonwealth of Massachusetts 5

General safety 5

Fire safety 6

Gas safety 6

Electrical and grounding safety 7

Installation safety 7

Location safety 8

Cooktop safety 9

Oven safety 10

Self-cleaning oven safety 10

Gas range components 11

Overview 11

Dual Fuel range specications 11

Installation requirements 13

Location requirements 13

Installation guide 14

To remove safely from the pallet 15

To avoid breakage 15

Gas requirements 16

Special gas requirements (gas models sold in Massachusetts) 17

Electrical requirements 17

Tools and materials 19

What’s in the box 19

Installation instructions 20

Installing your Dual fuel Range 20

Install_NY9900R_CHEF_NY36R9966PS_AA_DG68-01106B-01_EN+MES+CFR.indb 3 2019-03-14  3:55:49

4 English

Before you begin

Important safety information

Read all instructions before using this appliance

• All electrical and gas equipment with moving parts can be dangerous. Please

read the important safety instructions for this appliance in this manual. The

instructions must be followed to minimize the risk of injury, death, or property

damage.

• Save this manual. Please Do Not Discard.

Symbols used in this manual

WARNING

Hazards or unsafe practices that may result in severe personal injury or death.

CAUTION

Hazards or unsafe practices that may result in electric shock, personal injury or

property damage

NOTE

Useful tips and instructions

These warning icons and symbols are here to prevent injury to you and others.

Please follow them explicitly. After reading this section, keep it in a safe place for

future reference.

Before you begin

About this manual

Read these instructions completely and carefully.

Important note to the installer

• Read all instructions contained in these installation instructions before

installing the range.

• Remove all packing materials from the oven compartments before connecting

the electric and gas supply to the range.

• Observe all governing codes and ordinances.

• Be sure to leave these instructions with the consumer.

• Installation of this appliance requires basic mechanical skills.

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not covered under the Warranty.

Important note to the consumer

Keep these instructions with your user manual for future reference.

• As when using any appliance generating heat, there are certain safety

precautions you should follow.

• Be sure your range is installed and grounded properly by a qualied installer

or service technician.

• Make sure the wall coverings around the range can withstand the heat

generated by the range.

• Cabinet storage space above the surface burners should be a minimum of

30 in (76.2 cm).

Important note to the servicer

The electrical diagram is in an envelope attached to the back of the range.

Install_NY9900R_CHEF_NY36R9966PS_AA_DG68-01106B-01_EN+MES+CFR.indb 4 2019-03-14  3:55:49

English 5

Important safety information

• Remove all packaging materials from the range before operating to prevent

ignition of these materials. Keep all packaging materials out of children’s

reach. Properly dispose the packaging materials after the range is unpacked.

• Do not store any object of interest to children on the cooktop or backguard

of the range. Children climbing on the range to reach items could be killed or

seriously injured.

• Do not operate the range if the range or any part of the range is damaged,

malfunctioning, or missing parts.

• Do not use the range as a space heater. This range is to be used for cooking

purposes only.

• Do not use oven cleaners or oven liners in or around any part of the oven.

• Use only dry pot holders.

• Do not use the range to heat unopened food containers.

• Do not strike the oven glass.

• When disposing of the range, cut off the power cord and remove the door.

• Unplug or disconnect power before servicing.

• Make sure all meat and poultry is cooked thoroughly. Meat should always be

cooked to an internal temperature of 160 °F (71 °C). Poultry should always be

cooked to an internal temperature of 180 °F (82 °C).

California Proposition 65 Warning

WARNING

Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Commonwealth of Massachusetts

This product must be installed by a licensed plumber or gas tter qualied or

licensed by the State of Massachusetts. When using ball-type gas shut-off valves,

you must use the T-handle type. Multiple exible gas lines must not be connected

in series.

General safety

WARNING

To reduce the risk of re, electric shock, personal injuries, and/or death, obey the

following precautions.

• Do not touch any part of the range,

including but not limited to, oven

burners, surface burners, or interior

surfaces during or immediately after

cooking.

• Know the location of the gas shut-

off valve and how to shut it off.

• Make sure the anti-tip device is properly installed on the range. See the

installation instructions for more information.

• Do not let children near, in, or on the range. Do not let children play with the

range or any part(s) of the range. Do not leave children unattended in an area

where the range is in use. For children’s safety, we recommend utilizing the

control/door lockout feature.

Install_NY9900R_CHEF_NY36R9966PS_AA_DG68-01106B-01_EN+MES+CFR.indb 5 2019-03-14  3:55:49

6 English

Important safety information

Gas safety

WARNING

To reduce the risk of re, electric shock, personal injuries, and/or death, obey the

following precautions.

If you smell gas:

• Close the valve and do not use the range.

• Do not light a match, candle, or cigarette.

• Do not turn on any gas or electric appliances.

• Do not touch any electrical switches or plug a power cord into an outlet.

• Do not use any phone in your building.

• Evacuate the room, building, or area of all occupants.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier, call the re department.

Checking for gas leaks

• Leak testing of the appliance shall be conducted according to the

manufacturer’s instructions. Do not use a ame to check for gas leaks. Use a

brush to spread a soapy water mixture around the area you are checking. If

there is a gas leak, you will see small bubbles in the soapy water mixture at

the leak point.

Fire safety

WARNING

To reduce the risk of re, electric shock, personal injuries, and/or death, obey the

following precautions.

• Do not store, place, or use ammable

or combustible materials such

as paper, plastic, pot holders,

linens, curtains, gasoline or other

ammable vapors or liquids near the

range.

• Do not wear loose tting or hanging

garments while using the range.

• To avoid grease buildup, regularly clean the vents.

• Do not let pot holders or other ammable materials touch a heating element.

Do not use a towel or other bulky cloths in place of a pot holder.

• Do not use water on a grease re. To put out a grease re, turn off the heat

source and smother the re with a tight-tting lid or use a multipurpose dry

chemical or foam-type re extinguisher.

• If a grease re should occur in the oven, turn off the oven by rotating the

mode selector knob to the OFF position. Keep the oven door closed until the

re goes out. If necessary, use a multipurpose dry chemical or foam-type re

extinguisher.

• Do not heat unopened food containers - buildup of pressure may cause

container to burst and result in injury.

Install_NY9900R_CHEF_NY36R9966PS_AA_DG68-01106B-01_EN+MES+CFR.indb 6 2019-03-14  3:55:50

English 7

Important safety information

Installation safety

WARNING

To reduce the risk of re, electric shock, personal injuries, and/or death, obey the

following precautions.

∗

• Have your range installed and

properly grounded by a qualied

installer, in accordance with the

installation instructions. Any

adjustment and service should

be performed only by qualied

gas range installers or service

technicians.

• Do not attempt to service, modify, or replace your range or any part of your

range unless it is specically recommended in this manual. All other service

should be referred to a qualied technician.

• Always use new exible connectors when installing a gas appliance. Do not

use old exible connectors.

• Make sure the anti-tip device is properly installed on the range. See the

installation instructions for more information.

• Due to the size and weight of the range, have two or more people move the

range.

• Remove all tape and packaging materials.

• Remove all accessories from the cooktop and oven. Grates are heavy. Use

caution when handling them.

• Make sure no parts came loose during shipping.

Electrical and grounding safety

WARNING

To reduce the risk of re, electric shock, personal injuries, and/or death, obey the

following precautions.

• Plug into a grounded 3-prong outlet.

• Do not remove the ground prong.

• Do not use an adapter or an

extension cord.

• Do not use a damaged power plug,

power cord, or loose power outlet.

• Do not modify the power plug,

power cord, or power outlet in any

way.

• Do not put a fuse in a neutral or ground circuit.

• Use a dedicated 240-volt, 60-Hz, 40-amp, AC, fused electrical circuit for this

range. A time-delay fuse or circuit breaker is recommended. Do not plug more

than one appliance into this circuit.

• Do not connect the ground wire to plastic plumbing lines, gas lines, or hot

water pipes.

• This range must be Earth grounded. In the event of a malfunction or

breakdown, grounding will reduce the risk of electrical shock by providing

a path for the electric current. This range is equipped with a cord having

a grounding plug. The plug must be rmly plugged into an outlet that is

properly installed and grounded in accordance with the local codes and

ordinances. If you are unsure whether your electrical outlet is properly

grounded, have it checked by a licensed electrician.

• Electrical service to the range must conform to local codes. Barring local

codes, it should meet the latest ANSI/NFPA No. 70 – Latest Revision (for the

U.S.) or the Canadian Electrical Code CSA C22.1 – Latest Revisions.

• It is the personal responsibility of the range owner to provide the correct

electrical service for this range.

Install_NY9900R_CHEF_NY36R9966PS_AA_DG68-01106B-01_EN+MES+CFR.indb 7 2019-03-14  3:55:50

8 English

Important safety information

Location safety

WARNING

To reduce the risk of re, electric shock, personal injuries, and/or death, obey the

following precautions.

• This range is for indoor, household use

only. Do not install the range in areas

exposed to the weather and/or water.

• Do not install the range in a place

which is exposed to a strong draft.

• Select a level, well-constructed oor that can support the range’s weight.

Synthetic ooring, such as linoleum, must withstand 180 °F (82 °C)

temperatures without shrinking, warping, or discoloring. Do not install

the range directly over interior kitchen carpeting unless a sheet of ¼ inch

plywood or a similar insulator is placed between the range and carpeting.

• Select a location where a grounded, 3- prong outlet is easily accessible.

• If the range is located near a window, do not hang long curtains or paper

blinds on that window.

• For the range to ventilate properly, make sure the range’s vents are not

blocked or covered, and that there is enough clearance at the top, back, sides,

and underneath the range. The vents allow the necessary exhaust for the range

to operate properly with correct combustion and get the good cooking result.

• Make sure the wall coverings around the range can withstand heat up to

194 °F (90 °C) generated by the range.

• Cabinet storage above the surface of the range should be avoided. If cabinet

storage above the range is necessary: allow a minimum clearance of 30 inches

(76.2 cm) between the cooking surface and the bottom of cabinets. For detail

information, please refer to the Minimum dimensions section on page 14.

• Make sure your range is correctly installed and adjusted by a qualied service

technician or installer for the type of gas (natural or LP) you will use. For

your range to utilize LP gas. The installer must replace the 6 surface burner

orices with the provided LP orice set. And reverse the GPR adapter. These

adjustments must be made by a qualied service technician in accordance

with the manufacturer’s instructions and all codes and requirements of the

authority having jurisdiction. The qualied agency performing this work

assumes the gas conversion responsibility.

• Installation of this range must conform with local codes or, in the absence of

local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA.54, latest

edition. In Canada, installation must conform with the current Natural Gas

Installation Code, CAN/CGA-B149.1, or the current Propane Installation Code,

CAN/CGA-B149.2, and with local codes where applicable. This range has been

design-certied by ETL according to ANSI Z21.1, latest edition, and Canadian

Gas Association according to CAN/CGA-1.1, latest edition.

Install_NY9900R_CHEF_NY36R9966PS_AA_DG68-01106B-01_EN+MES+CFR.indb 8 2019-03-14  3:55:50

English 9

Important safety information

• To avoid cookware discoloration, deformity, and/or carbon monoxide

poisoning, do not use cookware that is exceedingly larger than the grate.

• Make sure cookware handles are turned to the side or rear of the cooktop, but

not over other surface burners.

• Stand away from the range while frying.

• Always heat frying oils slowly, and watch as they heat. If you are frying foods

at high heat, carefully watch during the cooking process. If a combination of

fats or oils is to be used during frying, mix them together before heating.

• Use a deep-fryer thermometer whenever possible. This prevents overheating

the fryer beyond the smoking point.

• Use a minimum amount of oil when shallow pan-frying or deep-frying. Avoid

cooking unthawed food or food with excessive amounts of ice.

• Before moving cookware full of fats or oils, make sure it has completely

cooled.

• To prevent delayed eruptive boiling, always allow heated liquids to stand at

least 20 seconds after you have turned off the burner so that the temperature

in the liquid can stabilize. In the event of scalding, follow these rst aid

instructions:

1. Immerse the scaled area in cool or lukewarm water for at least

10 minutes.

2. Do not apply any creams, oils, or lotions.

3. Cover with a clean, dry cloth.

Cooktop safety

WARNING

To reduce the risk of re, electric shock, personal injuries, and/or death, obey the

following precautions.

• Make sure all burners are off when not

in use.

• Do not use aluminium foil to line the

grates or any part of the cooktop.

• Do not leave burners unattended on

medium or high heat settings.

• Before igniting, make sure all burner

caps are properly in place and all

burners are level.

• Always use the Lite position when igniting the burners and make sure the

burners have ignited. If ignition fails, turn the knob to OFF and wait until the

gas has dissipated.

• When you set a burner to simmer, do not turn the knob quickly. Make sure the

ame stays on.

• Do not place any objects other than cookware on the cooktop.

• This cooktop is designed to cook with a wok or wok ring attachment. If foods

are amed, they should only be amed under a ventilation hood that is on.

• Before removing or changing cookware, turn off the burners.

• Remove food and cookware immediately after cooking.

• Before removing any parts of the burner for cleaning, make sure the range is

off and completely cool.

• After cleaning the burner spreader, make sure it is completely dry before re-

assembling.

• Make sure the spark mark on the dual burner spreader is placed beside the

electrode when it is assembled.

• To avoid carbon monoxide poisoning, do not pour water into the cooktop well

while cleaning.

• Select cookware that is designed for top-range cooking. Use cookware that is

large enough to cover the burner grates. Adjust the burner ames so that the

ames do not extend beyond the bottom of the cookware.

Install_NY9900R_CHEF_NY36R9966PS_AA_DG68-01106B-01_EN+MES+CFR.indb 9 2019-03-14  3:55:50

10 English

Important safety information

Self-cleaning oven safety

WARNING

To reduce the risk of re, electric shock, personal injuries, and/or death, obey the

following precautions.

• The self-cleaning feature operates the

oven at temperatures high enough

to burn away food soils in the oven.

The range is extremely hot during a

self-cleaning cycle. Do not touch any

surfaces of the range during a self-

cleaning cycle.

• Keep children away from the oven during a self-cleaning cycle.

• Before starting a self-cleaning cycle, remove all racks, cookware, and utensils

from the oven. Only porcelain-coated oven racks may be left in the oven.

• Before starting a self-cleaning cycle, wipe grease and food soils from the

oven.

• When opening the door after a self-cleaning cycle, stand away from the oven.

• If the self-cleaning cycle malfunctions, turn off the oven, disconnect the power

supply, and contact a qualied service technician.

Oven safety

WARNING

To reduce the risk of re, electric shock, personal injuries, and/or death, obey the

following precautions.

• Do not use the oven for non-cooking

purposes such as drying clothes or

storage. Use the oven for cooking

purposes only.

• Make sure the inner portion of the split

oven-rack is in the proper position

within the outer rack.

• Make sure the oven racks are placed on the same level on each side.

• Do not damage, move, or clean the door gasket.

• Do not spray water on the oven glass while the oven is on or just after you

have turned it off.

• Do not use aluminium foil or foil liners anywhere in the oven. Do not use

aluminium foil or like material to cover any holes or passages in the oven

bottom or to cover an oven rack.

• Stand away from the oven when opening the oven door.

• Keep the oven free from grease buildup.

• When repositioning the oven racks, make sure the oven is completely cool.

• Only use cookware that is recommended for use in gas ovens.

• To avoid damaging the burner control knobs, always bake and/or broil with

the oven door closed.

• Do not broil meat too close to the burner ame. Trim excess fat from meat

before cooking.

• When using cooking or roasting bags in the oven, follow the manufacturer’s

directions.

Install_NY9900R_CHEF_NY36R9966PS_AA_DG68-01106B-01_EN+MES+CFR.indb 10 2019-03-14  3:55:51

English 11

Gas range components

Cooktop Burner Placement Location Output Rating (Natural Gas)

LF

CF

RF

LR

CR

RR

Cooktop Burners

(under grates) Burner

Locations and Output Ratings

Left-Front (LF) 22,000 BTU

Left-Rear (LR) 16,000 BTU

Right-Front (RF) 22,000 BTU

Right-Rear (RR) 16,000 BTU

Center-Front (CF) 16,000 BTU

Center-Rear (CR) 16,000 BTU

Dual Fuel range specications

MODEL NY36R9966P*

Description Dual fuel Range

Overall dimensions 35 ⅞ in (W) × 37 ¼ in (H) × 29 ½ in (D)

911 mm (W) × 946 mm (H) × 750 mm (D)

Electrical Refer to the rating label.

Gas, NG (natural gas) 5–13 in WC

Gas, LP (liquid propane) 10–13 in WC

Surface burners (NG) (LF)–22,000 BTU / (LR)–16,000 BTU

(RF)–22,000 BTU / (RR)–16,000 BTU

(CF)–16,000 BTU / (CR)–16,000 BTU

Surface burners (LP) (LF)–16,500 BTU / (LR)–14,500 BTU

(RF)–16,500 BTU / (RR)–14,500 BTU

(CF)–14,500 BTU / (CR)–14,500 BTU

Oven heater Bake - 3000 W

Broil - 4400 W

Gas range components

Overview

MODEL NY36R9966P*

01

14

15

08

13

16

09

12

10

05

17

03

11

02

04

07

06

01 Surface burner knobs

(6 pcs)

02 Oven burner knobs

(mode, temperature)

(2 pcs)

03 Surface burners

04 Oven vent cover 05 Oven light button 06 Removable oven door

07 Kick panel 08 Broil oven heater 09 * Oven lights

(2 locations)

10 Convection fan 11 Ladder racks 12 Bake oven heater

13 Open / Close reservoir 14 Smart Control button

(beneath bullnose)

15 Display

16 Reservoir 17 LED Ambient Lighting

button (beneath

bullnose)

Install_NY9900R_CHEF_NY36R9966PS_AA_DG68-01106B-01_EN+MES+CFR.indb 11 2019-03-14  3:55:51

12 English

Gas range components

With grate

37

3

/8

" (94.9 cm) Min.

38

5

/8

" (98.1 cm) Max.

Without grate

36" (91.4 cm) Min.

37

¼

" (94.6 cm) Max.

35

⅞

"

(91.1 cm)

27

⅝

"

(70.0 cm)

49"

(124.7 cm)

28

¾

"

(73.0 cm)

29

½

" (75.0 cm)

With handle

29

7

/

8

’’ (75.8 cm)

With knobs

Install_NY9900R_CHEF_NY36R9966PS_AA_DG68-01106B-01_EN+MES+CFR.indb 12 2019-03-14  3:55:51

English 13

Installation requirements

13 in (33 cm)

Overhead

Cabinet Depth

0 in (0 cm)

22.6 in

(573.5 mm)

24 in

(61 cm) Lower

Cabinet Depth

6 in*

(15.2 cm)

6 in*

(15.2 cm)

37 ½ in

(953 mm)

36 in

(914 mm)

18 in

(45.7 cm)

30 in (76.2 cm)

0 in (0 cm)

Clearance Below

Cooking Top

and at Rear and

Sides of Range

* Side clearance above cooking surface to any objects, i.e., wall.

Installation requirements

Location requirements

Clearances and dimensions

NOTE

• For OTR over Gas Stove, please follow local GAS CODE.

• BEFORE YOU BEGIN to install this appliance, refer to the following information,

dimensions, and clearances. Do not locate the range where it may be subject

to strong drafts. Provide adequate clearances between the range and adjacent

combustible surfaces. These dimensions must be met for safe use of the range.

The location of the electrical outlet and gas piping may be adjusted to meet

the following dimensions and clearances.

• For installation in Canada, a free-standing range is not to be installed closer

than 4.7 in (12 cm) from any adjacent surface.

CAUTION

This range has been designed to comply with the maximum allowable wood

cabinet temperature of 194 °F (90 °C). Make sure the wall covering, countertops,

and cabinets around the range can withstand the heat (up to 194 °F [90 °C])

generated by the range. If not, discoloration, delamination, or melting may occur.

Install_NY9900R_CHEF_NY36R9966PS_AA_DG68-01106B-01_EN+MES+CFR.indb 13 2019-03-14  3:55:52

14 English

Installation requirements

Minimum dimensions

CAUTION

• If overhead cabinets are installed, a range hood should also be installed

and project horizontally a minimum of 5" (12.7 cm) beyond the front of the

cabinets. Hood is necessary to dissipate any heat buildup in the overhead

cabinets to prevent possibility of re, personal injury and/or death. The

ventilating hood must be constructed of sheet metal not less than 0.0122"

thick and installed above the cooktop with a clearance of not less than ¼"

between the hood and the underside of the combustible material or metal

cabinet. The hood must be at least as wide as the appliance and centered over

the appliance. Clearance between the cooking surface and the ventilation hood

surface must never be less than 24".

• Exception 1 : Installation of a listed microwave oven or cooking appliance

over the cooktop shall conform to the installation manual provided with the

appliance.

- 30" (76.2 cm) minimum clearance between the top of the cooking

surface and the bottom of an unprotected wood or metal cabinet; or If

30" (76.2 cm) clearance is not possible, minimum of 24" (61 cm) can be

used when the bottom of the wood or metal cabinet is protected by not

less than ¼" (0.64 cm) ame-retardant millboard covered with not less

than no. 28 MSG sheet steel, 0.015" (0.038 cm) stainless steel, 0.024"

(0.061 cm) aluminum, or 0.020" (0.051 cm) copper.

- 18" (45.7 cm) of minimum clearance between the countertop and the

adjacent cabinet bottom.

• Exception 2 : For island installation, maintain 2½" minimum from cutout

to back edge of countertop and 4" minimum from cutout to side edges of

countertop.

Installation guide

Recommended locations for gas piping and electrical outlets

A

B

Recommended

position for Gas stub

Recommended

position for

Electrical outlet

Model NY36R9966*

A

Electrical outlet

9 ⅞”(W) X 6 ⅞”(H) (25.1 cm x 17.5 cm)

B

Gas piping

17

15

/16" (W) X 5

3

/8''(H) (45.5 cm x 13.8 cm)

Install_NY9900R_CHEF_NY36R9966PS_AA_DG68-01106B-01_EN+MES+CFR.indb 14 2019-03-14  3:55:52

English 15

Installation requirements

To remove safely from the pallet

1. Remove the screws from the bottom

bracket on either side of the unit.

2. Press the bracket on either side to pull

out.

3. Have two persons hold both bottom

sides of the unit and lift up to remove

from the pallet. Use caution not to hold

the door handle.

To avoid breakage

CAUTION

• Please DO NOT push the unit strongly

when you install. These actions can

cause the damage to the unit.

• Hold the upper left/right area of the

door (not the door handle) with both

hands and push the unit in. Do not grab

the door handle.

Install_NY9900R_CHEF_NY36R9966PS_AA_DG68-01106B-01_EN+MES+CFR.indb 15 2019-03-14  3:55:53

16 English

Installation requirements

Fig. 1

C1

C2

C3

C4

1. The counter top around the cut-out

should be at and leveled (see hatched

area on Fig. 1).

2. Before installing the unit, measure the

heights of the two cabinet sides (C1–

C4), front and back (See Fig. 1) from the

oor to the top of the counter.

3. Level the range using the four leveling

legs so that the height from the oor

to the top of the cooktop frame is level

with a countertop.

4. Slide the unit into the cabinet (DO NOT

PUSH THE UNIT HARD). Make sure the

center of the unit aligns with the center

of the cabinet cut-out.

Gas requirements

Provide adequate gas supply

This range is designed to operate at a pressure of 5 in (13 cm) of water column on

natural gas or 10 in (25 cm) of water column on LP gas (propane or butane).

Make sure you are supplying your range with the type of gas for which it is

designed.

Do not attempt to convert the appliance from the gas specied in this manual to a

different gas without consulting the gas supplier.

This range is convertible for use on natural or propane gas. If you decide to use

this range on LP gas, conversion must be made by a qualied LP installer before

attempting to operate the range.

For proper operation, the pressure of natural gas supplied to the regulator must be

between 5 in and 13 in (13 cm and 33 cm) of water column.

For LP gas, the pressure supplied must be between 10 in and 13 in (25 cm and

33 cm) of water column.

When checking for proper operation of the regulator, the inlet pressure must be at

least 1 in (2.5 cm) greater than the operating (manifold) pressure as given.

The pressure regulator located at the inlet of the range manifold must remain in

the supply line regardless of whether natural or LP gas is being used.

A exible-metal appliance connector used to connect the range to the gas supply

line should have an I.D. of 0.5 in (1.3 cm) and be 5 ft (152 cm) in length for ease of

installation. In Canada, exible connectors must be single-wall metal connectors no

longer than 6 ft (183 cm) in length.

Do not kink or damage the exible metal tubing when moving the range.

Install_NY9900R_CHEF_NY36R9966PS_AA_DG68-01106B-01_EN+MES+CFR.indb 16 2019-03-14  3:55:53

English 17

Installation requirements

Special gas requirements (gas models sold in Massachusetts)

COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS:

WARNING

• Gas leaks may occur in your system, creating a dangerous situation.

- Gas leaks may not be detected by smell alone.

- Gas suppliers recommend you purchase and install a UL-approved

gas detector. Gas detector should be installed in accordance with the

manufacturers instructions.

• Range must be installed by a qualied plumber or gas tter by the State of

Massachusetts.

• A T-handle manual gas valve MUST be installed in the gas supply line to your

range.

• If a exible gas connector is used to install your range, multiple exible gas

lines must not be connected in series.

Electrical requirements

WARNING

To reduce the risk of re, electric shock, or personal injury:

All ranges

• Do not use an extension cord or adapter plug with this range.

• This range must be properly grounded.

• Check with a qualied electrician if you are in doubt as to whether your range

is properly grounded.

• Do not modify the plug provided with your range—if it doesn’t t the outlet,

have a proper outlet installed by a qualied electrician.

• All wiring and grounding must be done in accordance with local codes or, in

the absence of local codes, with the National Electrical Code, ANSI/NFPA No.

70 – Latest Revision (for the U.S.) or the Canadian Electrical Code CSA C22.1 –

Latest Revisions and local codes and ordinances.

• Wiring diagram is located on the back of the range. (Inside of the cover back

wire)

• This range is equipped with an electronic ignition system that will not operate

if plugged into an outlet that is not properly polarized.

Dual fuel models

• Canada models are equipped with a power cord with an equipment-grounding

conductor and a grounding plug.

(The power cord is not provided in US model.)

• A 240-Volt, 60-Hz, AC, approved electrical service with 40-amp circuit breaker

or time-delay fuse is required for all U.S. and Canadian models.

• Check for ¾-in (1.9-cm) UL-listed strain relief where the power cord comes out

of the range cabinet.

• Do not reuse a power supply cord from an old range or other appliance.

• The power cord electric supply wiring must be retained at the range cabinet

with a suitable UL-listed strain relief.

• A time-delay fuse or circuit breaker is also recommended.

Install_NY9900R_CHEF_NY36R9966PS_AA_DG68-01106B-01_EN+MES+CFR.indb 17 2019-03-14  3:55:54

18 English

Installation requirements

Usage situations where appliance power cord will be disconnected frequently

Do not use an adapter plug in these situations because disconnecting of the power

cord places under strain on the adapter and leads to eventual failure of the adapter

ground terminal. 240 V plug have 3 or 4 prongs and are not supplied with a unit.

Additional installation requirements for mobile homes

The installation of appliances designed for mobile home installation must conform

with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part

3280 (formerly the Federal Standard for Mobile Home Construction and Safety,

Title 24, HUD, Part 280) or, when such standard is not applicable, the Standard

for Manufactured Home Installations, latest edition (Manufactured Home Sites,

Communities and Set-Ups), ANSI A225.1, latest edition, or with local codes. In

Canada, mobile home installation must be in accordance with the current CAN/CSA

Z240/MH Mobile Home Installation Code.

Power cord location

The power cord for this appliance is located

on the back of the range, near the bottom

left corner.

Grounding

• All ranges must be grounded for personal safety.

• All gas models have a power cord with an equipment-grounding conductor

and a grounding plug.

• The plug must be rmly plugged into a 3-prong or 4-prong outlet that is

properly installed and grounded in accordance with all local codes and

ordinances. In the event of a malfunction or breakdown, grounding will

decrease the risk of electrical shock by providing a path for the electric

current.

• Do not use a damaged power plug or loose wall outlet.

• Do not use an extension cord or adapter with this appliance.

• Do not, under any circumstances, cut, modify, remove, or otherwise defeat the

grounding if quipped. If the plug and the outlet do not match or you have any

doubt, have a qualied electrician install the proper outlet.

The customer should have the wall receptacle and circuit checked by a

qualied electrician to make sure the receptacle is properly grounded.

Ground Fault Circuit Interrupters(GFCIs) are not required or recommended for

range receptacles.

• NEVER connect ground wire to plastic plumbing lines, gas lines, or water

pipes.

CAUTION

Failure to follow these instructions can result in death, re, or electrical shock.

Install_NY9900R_CHEF_NY36R9966PS_AA_DG68-01106B-01_EN+MES+CFR.indb 18 2019-03-14  3:55:54

English 19

Tools and materials

Parts needed

4-wire cord or

3-wire cord

Gas line

shut-off valve

Flexible metal

appliance connector

½" (ID) x 5 ft

Flare union adapter

¾" or ½" (NPT) x ½" (ID)

Flare union adapter

½" (NPT) x ½" (ID)

135-degree elbow

(optional)

Lag bolt or ½" (OD)

sleeve anchor

Tools needed

Flat-blade

screwdriver

Phillips

screwdriver

Open-end or

adjustable wrench

Pipe wrench (2)

Pencil and ruler Level

Pipe joint

compound

Nut driver

Utility knife

Soapy water

solution

Tools and materials

What’s in the box

Parts supplied

Surface burner grates (3) Surface burners and caps (6)

Flat rack (1) Anti-tip bracket kit

Wok grate (1) Gliding rack (2)

Temp. Probe (1) Front leg covers (2)

NOTE

• Make sure you have received all of the supplied parts shown above.

• If your range was damaged during shipping or you do not have all of the

supplied parts, contact your local retailer.

Install_NY9900R_CHEF_NY36R9966PS_AA_DG68-01106B-01_EN+MES+CFR.indb 19 2019-03-14  3:55:56

20 English

Installation instructions

Installation instructionsInstallation instructions

Installing your Dual fuel Range

NOTE

• IMPORTANT: Please read the following instructions, as well as the Important

Safety Instructions section at the front of this manual, completely and

carefully BEFORE installing and/or operating the gas range. Improper

installation, adjustment, service, or maintenance can cause personal injury or

property damage.

• To order parts or accessories, contact

your local retailer or refer to the last

page.

• To ensure proper installation, we

strongly recommend that you hire a

professional installer.

Step 1. Unpack the range

Remove all packaging materials. Failure to remove packaging materials could

result in damage to the appliance.

Inventory all loose parts against the 'Parts supplied' overview on page 19.

Check for shipping damage and/or missing parts. Any damage and/or missing

parts should be reported to your local retailer.

Step 2. Meeting electrical connection requirements

CAUTION

For personal safety, do not use an extension cord with this appliance. Remove

house fuse or open circuit breaker before beginning installation.

This appliance must be supplied with the proper voltage and frequency, and

connected to an individual properly grounded branch circuit, protected by a circuit

breaker or fuse having amperage as specied on the rating plate. The rating plate

is located above the drawer on the oven frame.

We recommend you have the electrical wiring and hookup of your range

connected by a qualied electrician. After installation, have the electrician show

you where your main range disconnect is located.

Check with your local utilities for electrical codes which apply in your area. Failure

to wire your oven according to governing codes could result in a hazardous

condition.

If there are no local codes, your range must be wired and fused to meet the

requirements of the National Electrical Code, ANSI/NFPA No. 70–Latest Edition.

You can get a copy by writing:

National Fire Protection Association

Batterymarch Park

Quincy, MA 02269

Effective January 1, 1996, the National Electrical Code requires that new

construction (not existing) utilize a 4-conductor connection to an electric range.

When installing an electric range in new construction, follow Steps 2 and 3 for

4-wire connection.

You must use a 3-wire or 4-wire, single-phase A.C. 208Y/120 Volt or 240/120 Volt,

60 hertz electrical system.

If the electrical service provided does not meet the above specications, have a

licensed electrician install an approved outlet.

Use only a 3-conductor or a 4-conductor UL-listed range cord. These cords may be

provided with ring terminals on wire and a strain relief device.

A range cord rated at 40 amps with 125/250 minimum volt range is required.

Install_NY9900R_CHEF_NY36R9966PS_AA_DG68-01106B-01_EN+MES+CFR.indb 20 2019-03-14  3:55:57

La page charge ...

Samsung NY36R9966PM/AA Manuel utilisateur

Ce manuel convient également à

Samsung NY36R9966PM/AA Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents