GE ZICS360NVLH Guide d'installation

INSTALLATION

INSTRUCTIONS

with Design Guide

36” Built-In Bottom-Freezer Refrigerators

Pour obtenir une version française de ce manuel d’instructions,

visitez notre site monogram.com.

Para consultar una version en español de este manual de instrucciones,

visite nuestro sitio de internet monogram.com.

MONOGRAM.COM

2

Safety Information

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT – Save these instructions for

local inspector’s use. Observe all governing codes and

ordinances.

•

Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions with

your Owner’s Manual for future reference.

If you received a damaged unit, you should immediately

contact your dealer or builder.

Skill Level – Installation of this unit requires basic

mechanical, carpentry and plumbing skills. Proper

installation is the responsibility of the installer. Product

failure due to improper installation is not covered under

the Monogram Warranty. See the Owner’s Manual for

warranty information.

For Monogram local service in your area, visit monogram.com

For Monogram service in Canada, visit monogram.ca

For Monogram Parts and Accessories, visit monogram.com/use-and-care/parts

WARNING

Tip Over Hazard.

These appliances are top heavy, especially with any doors open, and must be secured to prevent tipping

forward which could result in death or serious injury. Read and follow the entire installation instructions for

securing the appliance with the anti-tip system.

WARNING

Fire or Explosion Hazard.

Keep flammable materials and vapors away from appliance. Failure to do so can result in fire, explosion,

or death.

WARNING

To reduce the risk associated with choking, do not allow children under 3 years of age to

have access to small parts during the installation of this product.

CAUTION

Lifting Hazard

This unit is very heavy. To reduce the risk of person injury during maneuvering and installing this appliance,

3 people are required for proper installation.

CAUTION

Keep fingers out of the “pinch point” areas; clearances between the doors and between the

doors and cabinet are necessarily small. Be careful closing doors when children are in the area.

WARNING

Electrical Shock Hazard.

Plug into a grounded 3-prong outlet.

Do not remove the ground prong.

Do not use an adapter.

Immediately discontinue use of a damaged supply cord.

If the supply cord is damaged it must be replaced by a

qualified service professional with an authorized service

part from the manufacturer.

Do not use an extension cord with this appliance.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Follow the instructions in the section Grounding the unit.

This appliance must be installed with a means in the

fixed house wiring or circuit breaker for disconnecting the

appliance from the electrical supply after installation.

31-1000452 Rev. 1

3

Consignes de sécurité

AVANT DE COMMENCER

Veuillez lire toutes ces instructions attentivement.

• IMPORTANT – Conservez ces instructions à

l’usage de l’inspecteur local. Observez tous les codes et

décrets en vigueur.

•

Note à l’installateur – Assurez-vous de laisser ces

instructions au consommateur.

•

Note au consommateur - Conservez ces instructions

avec votre manuel d’utilisation pour

consultation ultérieure.

Si vous avez reçu un appareil endommagé, veuillez

communiquer immédiatement avec votre revendeur ou votre

entrepreneur.

Niveau de compétence – L’installation de cet appareil

exige des compétences de base en mécanique, menuiserie

et plomberie. La responsabilité d’une installation adéquate

relève de l’installateur. La garantie Monogram ne couvre

pas les défectuosités du produit causées par une installation

inadéquate. Consultez le manuel d’utilisation pour des

renseignements sur la garantie.

AVERTISSEMENT

Risque de basculement.

Ces électroménagers sont lourds du haut, notamment lorsqu’une porte est ouverte, de sorte qu’ils doivent être fixés pour

prévenir un basculement vers l’avant susceptible d’occasionner des blessures graves ou la mort. Lisez et observez la totalité des

instructions d’installation pour connaître la façon de fixer l’électroménager sur le dispositif antibasculement.

AVERTISSEMENT

Risque d’incendie ou d’explosion.

Gardez les matériaux et les vapeurs inflammables à l’écart de l’appareil. L’omission de prendre cette précaution peut entraîner un

incendie, une explosion ou la mort.

AVERTISSEMENT

Pour réduire le risque d’étouffement pendant l’installation de ce produit, ne pas laisser les petites pièces

à la portée des enfants âgés de moins de 3 ans.

AVERTISSEMENT

Risque lié à la manipulation d’un objet lourd

Cet appareil est très lourd. Afin de réduire le risque de blessure pendant la manipulation et l’installation de cet électroménager, la

participation de 3 personnes est nécessaire à l’exécution d’une installation correcte.

AVERTISSEMENT

Gardez vos doigts éloignés des points de pincement. Les espaces entre les portes et ceux entre les

portes et l’armoire sont particulièrement restreints. Soyez prudent lorsque vous fermez les portes en présence d’enfants.

AVERTISSEMENT

Risque d’électrocution.

Branchez l’appareil dans une prise à 3 broches mise à la terre.

N’enlevez pas la broche de mise à la terre.

N’utilisez pas un adaptateur.

Cessez immédiatement l’utilisation d’un cordon électrique

endommagé. Si le cordon électrique est endommagé, son

remplacement doit être exécuté par un technicien en réparation

qualifié au moyen d’un cordon de rechange autorisé par le

fabricant.

N’utilisez pas un cordon de rallonge avec cet électroménager.

Le non-respect de ces instructions peut occasionner un décès,

un incendie ou un choc électrique

Suivez les instructions de la section Mise à la terre de l’appareil.

Le circuit électrique auquel cet électroménager sera raccordé

doit comporter un disjoncteur ou un autre dispositif permettant

de couper l’alimentation électrique à l’appareil après l’installation.

Pour joindre le service Monogram de votre région, visitez monogram.com

Pour le service Monogram au Canada, visitez monogram.ca

Pour le service des Pièces et accessoires Monogram, visitez monogram.com/use-and-care/parts.

31-1000452 Rev. 1

4

Información sobre Seguridad

ANTES DE COMENZAR

Lea estas instrucciones en su totalidad y atentamente.

•

IMPORTANTE – Conserve estas

instrucciones para uso del inspector local. Cumpla con

todos los códigos y ordenanzas gubernamentales.

•

Nota para el Instalador – Asegúrese de entregarle

estas instrucciones al Comprador.

• Nota para el Consumidor – Guarde estas

instrucciones con su Manual del Propietario para

referencia futura.

Si la unidad que recibió está dañada, se deberá

comunicar de inmediato con su vendedor o fabricante.

Nivel de habilidad – La instalación de esta unidad

requiere un nivel básico de habilidades mecánicas,

de carpintería y plomería. La correcta instalación

del producto es responsabilidad del instalador. Si se

producen fallas en el producto debido a una instalación

inadecuada, la Garantía de Monogram no cubrirá las

mismas. Para obtener información sobre la garantía,

consulte el Manual del Propietario.

ADVERTENCIA

Riesgo de Caídas

Estos electrodomésticos son inestables, especialmente cuando una puerta se encuentre abierta, y deben estar

asegurados a fin de evitar caídas hacia adelante que podrían resultar en la muerte o en lesiones graves. Lea y siga

las instrucciones de instalación en su totalidad para asegurar el electrodoméstico con el sistema anti volcaduras.

ADVERTENCIA

Peligro de Incendio o Explosión

Mantenga cualquier material y vapores inflamables alejados del electrodoméstico. Si no se cumple con esto, se podrá

producir una explosión, un incendio o la muerte.

ADVERTENCIA

A fin de reducir el riesgo asociado con descargas, no permita que los niños menores de 3

años de edad tengan acceso a las partes pequeñas durante la instalación de este producto.

PRECAUCIÓN

Riesgo al levantar la puerta

Este refrigerador es muy pesado. A fin de reducir el riesgo de lesiones personales durante la maniobra e instalación

de este refrigerador, se requiere contar con 3 personas para una correcta instalación del modelo de 36” de ancho y

con 4 personas para una correcta instalación del modelo de 42” o 48”.

PRECAUCIÓN

Mantenga los dedos fuera de los espacios de “riesgo de lastimaduras”; los espacios entre

las puertas y entre las puertas y el gabinete son necesariamente pequeños. Tenga el cuidado de cerrar las puertas

cuando se encuentren niños en el área.

ADVERTENCIA

Riesgo de Descarga Eléctrica

Enchufe en un tomacorriente con conexión a tierra de 3

cables.

No elimine el cable de conexión a tierra.

No use un adaptador.

Inmediatamente interrumpa el uso de un cable de

suministro de corriente dañado. Si el cable de corriente se

encuentra dañado, su reemplazo deberá ser realizado por

un profesional calificado del servicio técnico, utilizando una

pieza del servicio técnico autorizada por el fabricante.

No use prolongadores con este electrodoméstico.

Si no se siguen estas instrucciones, se podrá producir la

muerte, incendios o descargas eléctricas.

Siga las instrucciones que figuran en la sección de

Conexión de Tierra de la unidad.

Este electrodoméstico deberá ser instalado por algún

medio en el cableado fijo del hogar o en un disyuntor para

desconectar el electrodoméstico del suministro eléctrico

luego de la instalación.

Para acceder al servicio local de Monogram en su área, visite monogram.com

Para acceder al servicio de Monogram en Canadá, visite monogram.ca

Para acceder a Piezas y Accesorios de Monogram, visite monogram.com/use-and-care/parts

31-1000452 Rev. 1

5

Contents

Safety 2

Instructions for Standard Installation 6

Planning Guide

The Installation Space 7

Dimensions and Clearances 7

Dual Installation 7

Customization Basics 8

Refrigerator Location 8

Optional Accessory Kits 8

1/4” Framed Panel Dimensions 9

3/4” Overlay Panel Dimensions 9

Side Panels 10

ZKBFN720NII Grille Panel Dimensions 10

130° Door Swing 11

Installation Instructions

Tools, Hardware, Materials 12

Grounding the Unit 12

Step 1. Remove Packaging 13

Step 2. Install Water Line 14

Step 2A. Water Line with Reverse Osmosis System

or other household filtration system 15

Step 3. Install Side Panels 15

Step 4. Anti-Tip Procedures 15

Step 5. Level Unit 17

Step 6. Secure Unit to Wall 17

Step 7. Alternate Anti-Tip Procedure 18

Step 8. Adjust Door Swing 18

Step 9. Install Grille Panel 19

Step 10. Install 1/4” Framed Panels 19

Step 10A. Install Overlay Panels 20

Step 11. Connect Water Supply 21

Step 12. Connect Power 21

Step 13. Start Icemaker 22

Step 14. Install Toekick 22

Instructions for Flush Installation 23

Instructions for Stainless Steel Installation 24

Planning Guide

The Installation Space 25

Dimensions and Clearances 25

Customization Basics 26

Side Panels 26

Optional Accessory Kits 26

Refrigerator Location 26

130° Door Swing 27

Installation Instructions

Tools, Hardware, Materials 28

Grounding the Refrigerator 28

Step 1. Remove Packaging 29

Step 2. Install Water Line 30

Step 2A. Water Line with Reverse

Osmosis System or other household

filtration system 31

Step 3. Install Side Panels 31

Step 4. Anti-Tip Procedure 31

Step 5. Level Refrigerator 33

Step 6, Secure Unit to Wall 33

Step 7. Alternate Anti-Tip Procedure 34

Step 8. Adjust Door Swing 34

Step 9. Connect Water Supply 35

Step 10. Connect Power 35

Step 11. Start Icemaker 36

Step 12. Install Toekick 36

31-1000452 Rev. 1

6

Instructions for Standard Installation

31-1000452 Rev. 1

7

THE INSTALLATION SPACE

Water And Electrical Locations

Electrical and water supply must be located as shown.

The Cutout Depth Must Be 24” (60.96 cm)

The refrigerator will project forward, slightly beyond

adjacent cabinetry, depending on your installation.

Allow minimum 1/8” (0.32 cm) air gap between case

back & wall.

Cutout depth beneath a soffit:

When installed beneath a soffit, the soffit cannot

exceed the 24” (60.96 cm) installation depth shown.

The top case trim overlaps the bottom of the soffit.

Additional Specifications

• A 115 volt 60Hz., 15 or 20 amp power supply is

required. An individual properly grounded branch

circuit or circuit breaker is recommended. Install

a properly grounded 3-prong electrical receptacle

recessed into the back wall. Electrical must be located

on rear wall as shown.

• Water line can enter the opening through the floor

or back wall. Route SmartConnect

™

kit or 1/4” O.D.

copper tubing between the cold water line and the

water connection location. The tubing should be

long enough to extend to the front of the refrigerator.

Installation of an easily accessible shut-off valve in

the water line is required.

DIMENSIONS AND CLEARANCES

Product Clearances

These refrigerators are equipped with a 3-position door

stop. The factory set 115° door swing can be adjusted

to 90° if clearance to adjacent cabinets or walls is

restricted.

Allow 23 7/8” (60.64 cm)

minimum clearance for a full

130° door swing. Allow 15” (38.1

cm) for pan removal.

For a 90° door swing, allow

4 9/16” min. (11.59 cm)

clearance to a wall. If the 90°

door stop position is used, pan

access is maintained, but pan

removal is restricted.

See illustration on page 11 to determine door swing

interaction with adjacent cabinets or countertops.

For Dual Installation

• If you are installing two refrigerators, side by side,

the installation space must be 71-1/2” (181.61 cm) wide.

NOTE: Additional cutout width may be required when

side panels are used. Add side panel thickness to the

finished cutout to calculate rough-in width.

• The water and electrical locations for each product

must be located as shown.

• A separate 115V, 60Hz., 15 or 20 amp power supply is

recommended for each product.

36" Frame to

Frame Width

*84" From

Floor to

Top Frame

35"

Case Width

*83 1/2"

at

Rear

25-3/8"

Case Depth

Depth Including

3/4” Panel - Handles: 25-15/16"

* Shipping height. The

refrigerator can be

adjusted to fit into a

cutout that is 84-1/2

”

(214.63 cm) max.

height. Note that the top

case trim at the front is

1/2

” (1.27 cm) higher

and will overlap upper

cabinetry or soffit. Use

leveling legs and wheels

for a maximum 1” (2.54

cm) height adjustment.

Design Guide - Standard Installation

115° Door Swing

16-7/8” Min.

to Wall

115°

130° Door Swing

130°

23-7/8”

Minimum

to Wall

36-1/2”

90º Door Swing

23-5/8”

Behind

Frame

4-9/16” Min. Distance to Wall

90°

6"

Wall View

Electrical

Area

84-1/2" max

Finished

Opening

75" From

Floor to

Bottom

of Electrical Area

10"

24" Cutout Depth

35-1/2"

Finished Width

2-5/16"

5"

10"

3-1/2" 3-1/2"

5"

3-1/2"

Water Supply

31-1000452 Rev. 1

8

CUSTOMIZATION BASICS:

Framed Or Overlay Panels, Custom

Handles and Accessory Kits

These refrigerators are designed to be customized with

decorative panels. Field installed custom door and grille

panels are required.

Side Panels

Side panels must be used whenever the sides of the

refrigerator will be exposed.

OPTIONAL ACCESSORY KITS

• ZKBSN720SS: Unification kit for an integrated

appearance on 2 stainless steel models installed

side-by-side.

• ZKBFN720NII: Unification kit for an intergraded

appearance on 2 custom panel models installed side-

by-side.

• ZKLN: Visor handle kit for use on custom panel

models in a standard installation.

Kit includes two handles.

• ZKFN: Flush inset installation kit required for all flush

installations. Includes modified toe kicks, case trim,

and other required components.

Design Guide - Standard Installation

REFRIGERATOR LOCATION

• Do not install the refrigerator where the temperature

will go below 55°F (13°C). It will not run often

enough to maintain proper temperatures.

• Do not install the refrigerator where temperatures will

go above 100°F (37°C). It will not perform properly.

• Do not install the refrigerator in a location exposed to

water (rain, etc.) or direct sunlight.

• Install it on a floor strong enough to support it fully

loaded.

31-1000452 Rev. 1

9

1/4” (0.63 cm) FRAMED PANEL DIMENSIONS

If you choose to install framed panels, they must be cut to the

dimensions shown. The panels will slide into the frame on the door,

drawer and grille.

If the custom panel is less than 1/4” thick and if it fits loosely in the

door frame, it can be backed up with a piece of filler material or foam

tape to improve the fit.

Spacer Panel

Backer Panel

Overlay Panel

Framed Panel Dimensions

1/4” (0.63 cm)

Framed Panel

A (Width) B (Grille Height) C (FF Height) D (FZ Height)

33-7/8”

(86.04 cm)

8-7/8”

(22.54 cm)

46-1/16”

(101.76 cm)

21-7/8”

(55.56 cm)

Overlay Panel Dimensions

1/4” (0.63 cm) Backer

Panel

A (Width) B (Grille Height) C (FF Height) D (FZ Height)

33-7/8”

(86.04 cm)

8-7/8”

(22.54 cm)

46-1/16”

(116.99 cm)

21-7/8”

(55.56 cm)

0.10” (0.25 cm) Spacer

Panel

32-1/2”

(82.55 cm)

7-5/8” (

20 cm)

44-11/16”

(113.51 cm)

20-1/2”

(52.07 cm)

3/4” (1.9 cm) Overlay

Panel

34-1/8”

(96.67 cm)

9” (22.86 cm) 46-5/16”

(117.63 cm)

22”

(55.88 cm)

NOTE: Left-to-right offset is not always equal to top-to-bottom offset.

1/4"

Panel

Door

5/16"

Trim

Reveal

IMPORTANT NOTE: Maximum total panel

weight:

• Fresh food door panel – 58 lbs. (26.31 kg)

• Freezer drawer panel – 28 lbs. (12.70 kg)

• Grille Panel – 11 lbs. (4.99 kg)

IMPORTANT NOTE: Maximum

total weight for the assembled

panels:

• Fresh food door panel – 58 lbs.

(26 kg)

• Freezer drawer panel – 28 lbs.

(13 kg)

• Grille Panel – 11 lbs. (5 kg)

Design Guide - Standard Installation

3/4” OVERLAY PANEL DIMENSIONS

For a more custom appearance, overlay panels may be

installed on trimmed models. The overlay panel must

be secured to a 1/4” (0.63 cm) thick backer panel which

slides into the trim. A spacer panel 0.10” (0.25 cm) thick

must be placed between the overlay and backer panel.

Assemble the panels with glue and screws.

• Center the spacer panel on the backer panel, left to

right and top to bottom. Secure the panels with glue.

• Center the spacer and backer panel on the overlay

panel and secure with glue and screws. Screws must

be countersunk into the backer panel.

31-1000452 Rev. 1

10

ZKBFN720NII GRILLE PANEL

DIMENSIONS

The ZKBFN720NII unification kit provides for the

installation of a framed or overlay grille panel.

Assemble the overlay panels in the same manner as

the door and drawer panels.

Design Guide - Standard Installation

SIDE PANELS

Side panels must be used whenever the sides of the

refrigerator will be exposed. The 1/4” (0.63 cm) side

panels will slip into the side case trim. Secure the

panels to the refrigerator with stick-on hook and loop

fastener strips. Order the side panels from the cabinet

manufacturer.

• Cut a notch in the top front corner as shown to allow

clearance for corner keys in the front side trim.

*84"

2-9/16"

24"

*3" to 4"

3/16"

1-7/8"

* Depending on

installation height.

Framed Panel Dimensions

1/4” (0.63 cm)

Framed Panel

A (Width) B (Height)

69-7/8” (177.48 cm) 8-7/8” (22.54 cm)

Overlay Panel Dimensions

1/4” (0.63 cm)

Backer Panel

A (Width) B (Height)

69-7/8” (177.48 cm) 8-7/8” (22.54 cm)

0.10” (0.25 cm)

Spacer Panel

68-1/2” (97.79 cm) 7-5/8” (20 cm)

3/4” (1.9 cm)

Overlay Panel

70-1/8” (178.12 cm) 9” (22.86 cm)

31-1000452 Rev. 1

11

1/4"

1/2"

3/4"

1"

1-1/4"

1"

3/4" Overlay

Panel

(Nominal Size)

Stainless Steel

1/4"

1/2"

3/4"

2"

1-1/4"

1-1/2"

1-3/4"

3"

2-1/4"

2-1/2"

2-3/4"

1/4"

1/2"

3/4"

Door

23-7/8" From

Rear of

Refrigerator

1"

Refrigerator

Case

Trim

Top View

130° DOOR SWING

Scale 1:1

Frameless Cabinets: The case trim

overlaps cabinets at the top and sides.

Therefore, frameless cabinets

may require filler strips to prevent

interference with cabinet door swing.

The opening must allow for filler strips.

Design Guide - Standard Installation

31-1000452 Rev. 1

12

TOOLS REQUIRED

• Tinsnips to cut banding

• Stepladder

• Bucket

• Level

• Appliance Hand Truck

• Tubing cutter

• 7/16” open-end wrench

• #2 Phillips screwdriver

• Drill and appropriate bits

• 5/16”, 7/16” socket

• Safety glasses

• 1-1/4” open end wrench

• Pliers

• 1/4” ratchet

HARDWARE SUPPLIED

• Water filter bypass plug

• Anti-Tip brackets

• 1/4” nut and ferrule

MATERIALS REQUIRED

• 35” long 2x4 for Anti-Tip support

• 1/4” copper water line tubing or SmartConnect

™

Refrigerator Tubing kits

• Water shut-off valve

• Custom panels for fresh food door, freezer drawer and

grille panel

• Screws to secure refrigerator to cabinetry.

• Stick-on hook and loop fastener strips for

1/4” (0.63 cm) side panels

FLOORING

For proper installation, this refrigerator must be placed

on a level surface of hard material that is at the same

height as the rest of the flooring. This surface should be

strong enough to support a fully loaded refrigerator, or

approximately 1,200 lbs. (544.31 kg).

NOTE: Protect the finish of the flooring. Cut a large

section of the cardboard carton and place under the

refrigerator where you are working.

Installation Instructions - Standard Installation

GROUNDING THE REFRIGERATOR

WARNING

Electrical Shock Hazard.

Failure to follow these instructions can result in death,

fire, or electrical shock.

The power cord of this appliance is equipped with a

3-prong (grounding) plug which mates with a standard

3-prong (grounding) wall receptacle to minimize the

possibility of electric shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly grounded.

Where a standard 2-prong wall outlet is encountered, it

is your personal responsibility and obligation to have it

replaced with a properly grounded 3-prong wall outlet.

DO NOT, UNDER ANY

CIRCUMSTANCES, CUT OR

REMOVE THE THIRD

(GROUND) PRONG FROM THE

POWER CORD.

DO NOT USE AN ADAPTER

PLUG TO CONNECT THE

REFRIGERATOR TO A

2-PRONG OUTLET.

DO NOT USE AN EXTENSION CORD

WITH THIS APPLIANCE.

MISE À LA TERRE DU

RÉFRIGÉRATEUR

AVERTISSEMENT

Risque de choc

électrique.

Le non-respect de ces instructions peut entraîner des

risques d’incendies, des chocs électriques ou la mort.

Le cordon d’alimentation de cet appareil est équipé

d’une fiche à trois broches (pour une mise à la terre)

qui s’adapte à la prise de courant standard à 3

broches (pour une mise à la terre) pour minimiser les

risques de chocs électriques par cet appareil.

Faites vérifier la prise murale et le circuit électrique par

un électricien qualifié pour s’assurer que le système

est correctement mis à la terre.

Dans le cas d’une prise biphasée, l’installateur a la

responsabilité et l’obligation de la remplacer par une

prise triphasée correctement mise à la terre.

NE COUPEZ PAS OU N’ENLEVEZ

PAS, SOUS AUCUN PRÉTEXTE,

LA TROISIÈME BROCHE DE

MISE À LA TERRE DU CORDON

D’ALIMENTATION.

N’UTILISEZ PAS D’ADAPTATEUR

POUR BRANCHER LE

RÉFRIGÉRATEUR À UNE PRISE

BIPHASÉE.

N’UTILISEZ PAS DE RALLONGE AVEC CET

APPAREIL.

31-1000452 Rev. 1

13

Installation Instructions - Standard Installation

STEP 1 REMOVE PACKAGING

WARNING

Tip Over Hazard.

The refrigerator is much heavier at the top than at the

bottom—be careful when moving. When using a hand

truck, handle from the side only.

AVERTISSEMENT

Risque de

basculement Le réfrigérateur est beaucoup plus lourd en

haut qu’en bas. Il faut être prudent lors des déplacements. Si

un diable est utilisé, il faut soulever le réfrigérateur sur le côté

seulement.

ADVERTENCIA

Riesgo de Caídas

El refrigerador es mucho más pesado en su parte superior

que en su parte inferior – tenga cuidado al moverlo. Al usar

un carro manual, sosténgalo de costado únicamente.

• Carefully cut banding at the top and bottom, remove

the outer carton.

• Slide out the back corner posts (2).

• Slide the carton off the top of the cabinet.

NOTE: IT IS NOT NECESSARY TO LAY THE

CABINET DOWN IN ORDER TO REMOVE THE SKID!

• The unit is secured to the

skid with 4 slotted tie-down

straps. Remove the six

7/16” bolts from the base

channels in the tie-downs.

• Remove the six 7/16” bolts

securing the straps to the

skid.

NOTE: DO NOT ATTEMPT

TO ROLL UNIT OFF SKID.

• The support blocks on the

bottom of the refrigeration

case must be removed

before the refrigerator is

taken off the skid or damage will occur. Carefully tilt

the refrigerator and slide the blocks out from beneath.

• Remove the toekick and set aside for final installation.

• Lift the refrigerator off the skid with an appliance dolly.

Handle from the sides.

STEP 1 REMOVE PACKAGING (Cont.)

Remove 2 strap

bolts on each side

Remove 5

base channel

bolts on each

side

CONEXIÓN A TIERRA DEL

REFRIGERADOR

ADVERTENCIA

Riesgo de Descarga

Eléctrica

Si no se siguen estas instrucciones, se podrá producir la

muerte, incendios o descargas eléctricas.

El cable de corriente de este electrodoméstico cuenta con

un enchufe de 3 cables (conexión a tierra) que se conecta a

un tomacorriente de pared estándar de 3 cables (conexión

a tierra) para minimizar el riesgo de posibles descargas

eléctricas por parte del mismo.

Contrate a un electricista calificado para que controle el

tomacorriente y el circuito eléctrico, a fin de asegurar que el

enchufe esté correctamente conectado a tierra.

En caso de contar con un tomacorriente de pared de 2

cables, es su responsabilidad y obligación reemplazarlo

por un tomacorriente de pared de 3 cables correctamente

conectado a tierra.

NUNCA, BAJO NINGUNA CIRCUNSTANCIA, CORTE NI

ELIMINE EL TERCER CABLE (TIERRA)

DEL CABLE DE CORRIENTE.

NO USE UN ENCHUFE ADAPTADOR

PARA CONECTAR EL REFRIGERADOR A

UN TOMACORRIENTE DE 2 PATAS.

NO USE UN PROLONGADOR CON ESTE

ELECTRODOMÉSTICO.

31-1000452 Rev. 1

14

STEP 2 INSTALL WATER LINE

(Cont.)

NOTE: The only Monogram-approved plastic tubing is

supplied in the SmartConnect

™

Refrigerator Tubing kits.

Do not use any other plastic water supply line because

the line is under pressure at all times. Other types of

plastic may crack or rupture with age and cause water

damage to your home.

SmartConnect

™

Refrigerator Tubing Kits are available

in the following lengths:

2’ (.6 m) - WX08X10002 8’ (2.4 m) - WX08X10006

15’ (4.6 m) - WX08X1 0015 25’ (7.6 m) - WX08X10025

Shut off the main water supply.

Turn on the nearest faucet long enough to clear the

line of water.

• Install a shut-off valve between the icemaker water

valve and cold water pipe in a basement or cabinet.

The shut-off valve should be located where it will be

easily accessible.

• Turn on the main water supply and flush debris.

Run about a quart of water through the tubing into a

bucket. Shut off water supply at the shut-off valve.

NOTE: Saddle type shut-off valves are included in

many water supply kits, but are not recommended for

this application.

NOTE: Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle

valves are illegal and use is not permitted in

Massachusetts. Consult with your licensed plumber.

STEP 2 INSTALL WATER LINE

• A cold water supply is required for automatic

icemaker operation. The water pressure must be

between 40 and 120 p.s.i. (275-827 kPa).

• Route 1/4” OD copper or SmartConnect

™

plastic

tubing between house cold water line and the water

connection location.

• Tubing should be

long enough to

extend to the front

of the refrigerator.

Allow enough tubing

to accommodate bend leading into the water line

connection.

Floor

Waterline Tubing

Installation Instructions - Standard Installation

WARNING

Connect to potable water supply only.

A cold water supply is required for automatic icemaker

operation. The water pressure must be between 40 and

120 psi (275-827 kilopascals).

WARNING

ELECTRIC SHOCK HAZARD

Attach tubing clamp using existing hole only. DO NOT drill

into the refrigerator.

AVERTISSEMENT

Raccordez l’appareil à une

alimentation d’eau potable seulement. Une alimentation

d’eau froide est requise pour faire fonctionner

la machine à glaçons et le pichet à remplissage

automatique. La pression d’eau doit se situer entre 40

et 120 psi. (275 à 827 kPa).

AVERTISSEMENT

RISQUE DE DÉCHARGE

ÉLECTRIQUE

Fixez le collier de serrage dans le trou présent seulement.

NE PERCEZ PAS dans le réfrigérateur.

ADVERTENCIA

Realice la conexión a un

suministro de agua potable únicamente. Se requiere

un suministro de agua fría para el funcionamiento de la

máquina de hielos automática y de la jarra de llenado

automático. La presión del agua deberá estar entre 40

y 120 p.s.i. (275 – 827 kPa).

ADVERTENCIA

PELIGRO DE DESCARGA

ELÉCTRICA

Adhiera la abrazadera de la tubería usando el agujero

existente únicamente. NO perfore el refrigerador.

31-1000452 Rev. 1

15

STEP 4 ANTI-TIP PROCEDURE

WARNING

Tip Over Hazard.

These refrigerators are top heavy, especially with

any doors open, and must be secured to prevent

tipping forward which could result in death or

serious injury. Read and follow the entire installation

instructions for securing the refrigerator with the

anti-tip system.

AVERTISSEMENT

Risque de

basculement Ces réfrigérateurs présentent une partie

supérieure lourde, en particulier avec une porte ouverte;

ils doivent donc être fixés pour prévenirle basculement

vers l’avant et le risque concomitant de blessure grave

ou fatale. Lisez et suivez les instructions d’installation

complètes pour l’installation du système anti-basculement.

ADVERTENCIA

Riesgo de Caídas

Estos refrigeradores son inestables, especialmente

cuando una puerta se encuentre abierta, y deberán estar

asegurados a fin de evitar caídas hacia adelante que

podrían resultar en la muerte o en lesiones graves. Lea y

siga las instrucciones de instalación en su totalidad para

asegurar el refrigerador con el sistema anti volcaduras.

• The kit supplied with the unit contains 2 lag bolts and

4 toggles with bolts. The wall bracket will be attached

to the wall in 4 places.

• Measure the opening where the unit is to be installed.

Mark the center with a vertical line.

Installation Instructions - Standard Installation

STEP 3 INSTALL SIDE PANELS

Skip this step when not using side panels.

If you are using 1/4” (0.63 cm) side panels, they should

be inserted into the case trim. Fasten the panels to the

refrigerator with stick-on hook and loop fastener strips

before setting refrigerator in place.

STEP 2A WATER LINE

INSTALLATION WITH A REVERSE

OSMOSIS SYSTEM OR OTHER

HOUSEHOLD FILTRATION SYSTEM

Skip this step when not using an RO System or

other household filtration system

If the water supply to the refrigerator is from a

household filtration system, use the refrigerator’s filter

bypass plug. Using the refrigerator’s water filtration

cartridge with the RO filter can result in hollow ice

cubes.

Filter Bypass Plug

31-1000452 Rev. 1

16

Installation Instructions - Standard Installation

STEP 4 ANTI-TIP PROCEDURE (CONT)

• Measure up 81 1/2” (207.01 cm) from the floor. Mark

this point on the wall.

• Using a level, draw a horizontal line on the wall at this

height.

• Locate at least 2 studs on the back wall. Mark these

points on the horizontal line.

• Place the bottom of the wall bracket with tabs on the

horizontal line. Align the center notch on the bracket

with the center line on the wall.

• The anti-tip wall bracket has a series of holes. Select 2

holes that match with the located studs. Make sure the

holes selected are on the center of the studs. Mark the

wall at these points.

• Mark an additional hole at each end of the bracket.

If one of the studs is closer to the end of the bracket,

mark an additional hole towards the center of the

bracket.

• Drill 1/2” (1.27 cm) holes into the wall board at the

locations marked for the toggles to be mounted (not the

stud markings).

• Drill 3/16” (0.47 cm)holes into wooden studs where

marked. If steel stud construction, drill 1/2” holes into

the studs where marked. You will use 2 toggles with

the metal studs.

Install Wall Toggles:

The wall toggles and bolts can be ordered as Service Kit

#WR49X10193. Wall toggles are installed in the drywall

and metal studs for stability. Install the wall toggles as

follows:

• Drill 1/2” (1.27 cm) holes at the wall markings made in

the holes at the ends of the wall bracket.

• Hold the metal channel flat against the plastic straps

and slide the channel through the hole.

• Gently pull back at the

ends of the plastic straps to

make the channel rest flush

behind the wall.

• Hold the ends of the straps

in one hand and slide the

plastic cap along the straps

until the flange of the cap is

flush with the wall.

• Place your thumb between the

plastic straps and bend up and

down to snap the straps off at

the wall.

Install Screws and Bolts:

• Have someone hold the wall bracket centered in place

with each of the holes aligned with the correct opening

in the bracket and level with the horizontal line.

• Insert the lag screws through the bracket and into the

stud. Tighten with a wrench.

• Insert the bolts into the toggle by hand until snug.

Tighten with a

wrench.

Line on Wall

Center

Two Additional

Hole Locations at

Ends of Brackets

Center

Wall Bracket

Line On Wall

Wall Studs

Plastic Straps

Metal Channel

Cap

Wood Stud

Lag Screw

Anti-Tip Wall Bracket

Bolt

Wall To

ggle

Drywall or

Steel Stud

31-1000452 Rev. 1

17

STEP 5 LEVEL REFRIGERATOR

All models have 4-point leveling. The front is supported

by leveling legs, the rear is supported by adjustable

wheels. Both are accessible from the front of the

refrigerator.

• To level the back of the refrigerator, turn the 7/16” hex

nut located above the front wheels. Turn clockwise to

raise or counterclockwise to lower the refrigerator.

• For front leveling, use a 1-1/4” (3.175 cm) open-end

wrench.

• Adjust height of

refrigerator to match

installation cutout

opening 83-1/2”

(212.09 cm) to

84-1/2” (214.63 cm).

The refrigerator

should be level and

plumb with cabinetry.

The rear leveling wheels and front leveling legs are

limited to a maximum height adjustment of 1”. If the

installation requires more than 84-1/2” (214.63 cm)

height, the installer should elevate the refrigerator on a

sheet of plywood or runners. Cabinetry trim could also

be added across the top of the opening to shorten the

opening. If you attempt to raise the refrigerator more

than 1” (2.54 cm), you will damage the front leveling

legs and the rear leveling wheels.

Installation Instructions - Standard Installation

STEP 4 ANTI-TIP PROCEDURE

(Cont)

CONNECT POWER CORD:

• Before pushing the refrigerator into the opening, plug

the power cord into the receptacle. Open the grille

panel on the left and reach into the opening at the

back to grasp the power cord. Pull the power cord

into the opening as you push the refrigerator back.

• Gently push refrigerator into the opening with hands

against front corners.

IMPORTANT: When the refrigerator is installed under

a soffit or if there is not enough height for this method

of security, brackets cannot be used. Proceed to step

6 to level the refrigerator and then to step 8 to secure

refrigerator to cabinets. See step 9 if you have metal

wall studs. The refrigerator must be secured to prevent

tipping.

STEP 6 SECURE UNIT TO WALL

• The “L” rod can be found in the upper left corner of

the unit in the access compartment. Look through the

access compartment to make sure the rod lines up

with the anti-tip bracket.

• There are 2 washers and a hair pin cotter with the rod.

Remove the washers and hair pin cotter from the end

of the rod.

• Rotate and move the “L” rod

into the slot in the anti-tip

bracket tab. Once it is in the

slot, rotate the “L” rod so

the hook portion is pointing

down. The holes at the front

end of the rod should be in a

vertical position.

• Pull out on the end of the rod

to make sure it is secure in the bracket.

• Locate the hole on the rod that is closest to the unit.

A hair pin cotter will be put through this hole to secure

the rod. If this hole appears to be too far away for a

snug fit against the unit, add the washers one at a

time until the pin will fit tightly into the hole.

• Align the straight section of the pin with the hole from

the underside of the rod. Push the pin up until it snaps

into position. Pliers may be used.

NOTE: The hair pin cotter

must be vertical when

this step is completed

to ensure the “L” rod is

engaged in the bracket.

• Check the rod for tightness

by pulling forward. If the

rod moves, remove the

hair pin cotter and place

another washer on the rod.

Reinsert the pin.

31-1000452 Rev. 1

18

Installation Instructions - Standard Installation

STEP 7 ALTERNATE ANTI-TIP

PROCEDURE

The refrigerator must be secured to prevent

tipping.

If the anti-tip bracket cannot be used, this alternate

procedure may be used to secure the refrigerator

against tip-over

• Raise the grille panel to access case trim.

• Use a 3/16” bit to drill four evenly spaced clearance

holes through the metal top case trim.

• Use a 1/16” bit to drill to pilot holes through the metal

clearance holes and into the wood soffit. The holes

should be centered in the soffit or a 3/4” min. wood

brace. The brace spanning the enclosure must be

securely fastened to cabinets on both sides.

• Install four, 1-1/2” (3.81 cm) drywall screws into the

pilot holes.

• If no soffit above the unit, drill screws into adjacent

cabinets through the side case trim.

STEP 8 ADJUST DOOR SWING

NOTE: This refrigerator has a 3-position door stop.

When space does not allow the door to swing open

fully to 115°, you may change the door swing to

a 90° opening. A 130° door swing is available for

standard installation only. If used for flush installation,

damage will occur to wood panels. Skip this step if

door opening is satisfactory for your installation

situation.

• Lift the grille panel to access the wire cover trim.

• Remove screws on both sides of the wire cover trim

and rotate off.

• Use pliers to unscrew door stop and reinstall into the

90° or 130° position.

• Reinstall the wire cover trim.

Top Case Trim

Install four 1-1/2” drywall screws through

trim and into soffit or 3/4” min. wood brace

3/4” Min.

Side View Top

Case Trim

Raise grille panel to

stop position

Drive screws through case

trim into adjacent cabinets

Pin Location

for 90°

Door Swing

Pin Location for

130° Door Swing

Pin Location as

Shipped for 115°

Door Swing

Remove wire cover trim

screws

31-1000452 Rev. 1

19

Installation Instructions - Standard Installation

STEP 10 INSTALL 1/4” (0.63 cm)FRAMED PANELS

Right hand models shown. Use the same instructions for left hand models.

IF YOU ARE INSTALLING OVERLAY PANELS, GO TO STEP 10A.

Install door and drawer panels:

• Open door to 90°.

• Remove 4 screws holding trim, lift off trim. Retain

screws.

• Slide framed panel into the door trim.

• There are two sets of holes in the handle side trim.

Replace handle side trim by installing the original

screws in the FRONT screw holes.

• Follow the same procedures to install the drawer

panel.

Optional visor handle shown from

kit ZKLN

STEP 9 INSTALL GRILLE PANEL

• Raise the access panel to the stop position.

• Loosen the screws on the side trim behind the frame.

Remove the bottom trim.

• Slide the panel over the metal baker panel and into the

trim.

• If necessary, tap with a wood block until the panel slips

under the top trim piece.

• Reassemble the bottom trim. Tighten the screws.

• Adjust the hinge spring to accommodate the panel

weight, if necessary.

Use rear holes to secure optional

ZKLN kit handle (not shown)

Use front holes

to secure trim

31-1000452 Rev. 1

20

Installation Instructions - Standard Installation

STEP 10A INSTALL OVERLAY PANELS

Custom handles

If you are using custom handles, the handle must be

properly secured to the panel before sliding the panel

into the trim.

• The cabinet manufacturer will supply the custom

handle and hardware.

• Secure the door/drawer trim using both the FRONT

and REAR screw holes.

Right hand models shown. Use the same

instructions for left hand models.

Install door and drawer panels:

• Open door to 90°.

• Remove 4 screws holding trim, lift off trim.

Retain screws.

• Slide overlay panel into the door trim.

• There are two sets of holes in the handle side trim.

Replace handle side trim by installing the original

screws in the REAR screw holes.

• Follow the same procedures to install the drawer

panel.

Use rear holes

to secure trim

Use front holes to secure optional

ZKLN kit handle (not shown)

Refrigerator Door

Door Trim

31-1000452 Rev. 1

La page charge ...

GE ZICS360NVLH Guide d'installation

GE ZICS360NVLH Guide d'installation

dans d''autres langues

Documents connexes

Autres documents