Faber Stratus 48 WH Guide d'installation

STRTIS48WHNB

STRTIS36WHNB

Installation Instructions

Use and Care Information

Instructions d'installation

Utilisez et d'entretien

Instrucciones de instalación

Información de uso y cuidado

STRATUS NB

2

3

Contents

Important Safety Instructions 4

Range hood Dimensions 7

Installation Height Requirements 7

Main Parts 8

Combinations Hoods And Motor Kits 10

Choose Your Ducting Method 11

Wiring Preparation 12

Ceiling Hood Install Preparation 13

Installation Information 14

Internal Blower Installation 15

External Blower Installation 17

Installation of Range Hood Body 19

Connect The Ducting 25

Wiring Box 2 Connection (Remote Blower Wiring Only) 27

House Wiring Box Connection 28

Use and Care Information 29

Wiring Diagram 32

4

READ AND SAVE THESE INSTRUCTIONS BEFORE YOU START INSTALLING

THIS RANGE HOOD

WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that

may ignite. Heat oils slowly on low or medium setting.

b)AlwaysturnhoodONwhencookingathighheatorwhenambeingfood(i.e.CrepesSuzette,Cherries

Jubilee,PeppercornBeefFlambé).

c)Cleanventilatingfansfrequently.Greaseshouldnotbeallowedtoaccumulateonfanorlter.

d)Useproperpansize.Alwaysusecookwareappropriateforthesizeofthesurfaceelement.

WARNING: - TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE

FIRE,OBSERVETHEFOLLOWING*:

a)SMOTHERFLAMESwithaclose-ttinglid,cookiesheet,ormetaltray,thenturnofftheburner.BECAREFULTO

PREVENTBURNS.IftheamesdonotgooutimmediatelyEVACUATEANDCALLTHEFIREDEPARTMENT.

b) NEVER PICK UP A FLAMING PAN - You may be burned.

c)DONOTUSEWATER,includingwetdishclothsortowels-aviolentsteamexplosionwillresult.

d)UseanextinguisherONLYif:

1. YouknowyouhaveaClassABCextinguisher,andyoualreadyknowhowtooperateit.

2. Thereissmallandcontainedintheareawhereitstarted.

3. Theredepartmentisbeingcalled.

4. Youcanghttherewithyourbacktoanexit.

* Based on "Kitchen Firesafety Tips" published by NFPA

WARNING-TOREDUCETHERISKOFFIREORELECTRICSHOCK,donotusethisfanwithanysolid-

state speed control device.

WARNING-TOREDUCETHERISKOFFIRE,ELECTRICALSHOCK,ORINJURYTOPERSONS,OBSERVE

THE FOLLOWING:

1. Usethisunitonlyinthemannerintendedbythemanufacturer.Ifyouhaveanyquestions,contact

the manufacturer.

2. Beforeservicingorcleaningunit,switchpoweroffatservicepanelandlocktheservicedisconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means

cannotbelocked,securelyfastenaprominentwarningdevice,suchasatag,totheservicepanel.

CAUTION:ForGeneralVentilatingUseOnly.DoNotUseToExhaustHazardousorExplosiveMaterials

and Vapors.

WARNING-TOREDUCETHERISKOFFIRE,ELECTRICALSHOCK,ORINJURYTOPERSONS,OBSERVE

THE FOLLOWING:

1. InstallationWorkAndElectricalWiringMustBeDoneByQualiedPerson(s)InAccordanceWithAll

ApplicableCodesAndStandards,IncludingFire-RatedConstruction.

2. Sufcientairisneededforpropercombustionandexhaustingofgasesthroughtheue(chimney)of

fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer's guideline

andsafetystandardssuchasthosepublishedbytheNationalFireProtectionAssociation(NFPA),and

theAmericanSocietyforHeating,RefrigerationandAirConditioningEngineers(ASHRAE),andthe

local code authorities.

3. Whencuttingordrillingintowallorceiling,donotdamageelectricalwiringandotherhiddenutilities.

4. Ducted fans must always be vented to the outdoors.

IMPORTANT SAFETY INSTRUCTIONS

5

ALL WALL AND FLOOR OPENINGS WHERE THE RANGE HOOD IS INSTALLED MUST BE SEALED.

This Range Hood requires at least 35" of clearance between the bottom of the Range Hood and the cooking

surface or countertop. This hood has been approved by UL at this distance from the cooktop.

Consult the cooktop or range installation instructions given by the manufacturer before making any cutouts.

MOBILE HOME INSTALLATION The installation of this Range Hood must conform to the Manufactured

Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD, Part 280).

Attention: This hood has been engineered to minimize electromagnetic interference (EMI) originating

from the consumer's home power source. However, in some home application, ambient EMI and

excessive EMI from other electronic sources can compromise the reliability of the remote control.

Please speak with your Faber Distributor about an optional spare part to further reduce EMI from

home sources.

• Venting system MUST terminate outside the home.

• DO NOT terminate the ductwork in an attic or other enclosed space.

• DO NOT use 4" laundry-type wall caps.

• Flexible-type ductwork is not recommended.

• DO NOT obstruct the ow of combustion and ventilation air.

• Failure to follow venting requirements may result in a re.

WARNING

!

VENTING REQUIREMENTS

Determine which venting method is best for your application. Ductwork can extend either through the wall or the roof.

The length of the ductwork and the number of elbows should be kept to a minimum to provide efcient performance. The

size of the ductwork should be uniform. Do not install two elbows together. Use duct tape to seal all joints in the ductwork

system. Use caulking to seal exterior walls and ceiling space opening around the cap.

Flexible ductwork is not recommended. Flexible ductwork creates back pressure and air turbulence

that greatly reduces performance.

Make sure there is proper clearance within the walls and ceiling space for exhaust duct before making cutouts. Do not

cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting frame must be constructed.

WARNING - To Reduce The Risk Of Fire, Use Only Metal Ductwork.

CAUTION-Toreduceriskofreandtoproperlyexhaustair,besuretoductairoutside–Donotventexhaustair

intospaceswithinwallsorceilingsorintoattics,crawlspaces,orgarages.

Cold Weather installations

An additional back draft damper should be installed to minimize backward cold air ow and a nonmetal-

lic thermal break should be installed to minimize conduction of outside temperatures as part of the vent

system. The damper should be on the cold air side of the thermal break. The break should be as close as

possible to where the vent system enters the heated portion of the house.

6

ELECTRICAL REQUIREMENTS

A 120 volt, 60 Hz AC-only electrical supply is required on a separate 15 amp fused circuit. A time-delay fuse or circuit breaker

is recommended. The fuse must be sized per local codes in accordance with the electrical rating of this unit as specied

on the serial/rating plate located inside the unit near the eld wiring compartment.

ELECTRICAL INSTALLATION WITH WIRING BOX

THIS UNIT MUST BE CONNECTED WITH COPPER WIRE ONLY. Wire sizes must conform to the requirements of the

National Electrical Code, ANSI/NFPA 70 - latest edition, and all local codes and ordinances. Wire size and connections

must conform with the rating of the appliance. Copies of the standard listed above may be obtained from:

National Fire Protection Association

Batterymarch Park

Quincy, Massachusetts 02269

This appliance should be connected directly to the fused disconnect (or circuit breaker) through exible, armored

or nonmetallic sheathed copper cable. Allow some slack in the cable so the appliance can be moved if servicing

is ever necessary. A UL Listed, 1/2" conduit connector must be provided at each end of the power supply cable

(at the appliance and at the junction box).

When making the electrical connection, cut a 1 1/4" hole. A hole cut through wood must be sanded until smooth.

A hole through metal must have a grommet.

• Electrical ground is required on this Range Hood.

• If cold water pipe is interrupted by plastic, nonmetallic gaskets or other materials, DO NOT use for

grounding.

• DO NOT ground to a gas pipe.

• DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral or grounding circuit could

result in electrical shock.

• Check with a qualied electrician if you are in doubt as to whether the Range Hood is properly

grounded.

• Failure to follow electrical requirements may result in a re.

WARNING

!

StateofCaliforniaProposition65Warning(USonly)

WARNING

This product contains chemicals known to the State of California to cause cancer and birth defects or other

reproductive harm.

For more information go to www.P65Warnings.ca.gov

7

RANGE HOOD DIMENSIONS

INSTALLATION HEIGHT REQUIREMENTS

Recommended 60" mounting height above the cooking surface for best performance, but can be mounted up

to 72" maximum away the cooking surface.

An access point to the hood from the ceiling or soft must be made for installation and future access to the

range hood.

MAX. 72" OVER ELECTRIC / GAS

MIN. 35" OVER ELECTRIC / GAS

8

MAIN PARTS

REF. PART QTY

A

Hood Body, complete with: Controls, Lights, Filters. 1

B

Upper Mounting Bracket 2

C

Lower Mounting Bracket 2

D

Damper ø 6" 1

E

Remote Control 1

H

Drilling Template 1

REF

PART

QTY

F

Torx Bolts (1/4" x 9/16")

4

G

Pozi Screws (1/8" x 3/8")

8

D

E

A

B

C

F

G

H

8

AA-725973-1

1x

C

1x

B

A

1x

3x 4x

1x

D E

1x

9

CAUTION - To Reduce The Risk Of Fire And Electric Shock, Install This Range Hood Only With

Remote Blower Models RB900 kit or RB1200 kit Manufactured by Faber Or Integral Blowers

Manufactured by Faber, Model(s) IB600 kit, IB400 kit, IB300 kit or generic remote blower rated max

2.7A suitable for use with solid state speed control.

PARTS NEEDED

PART

6" Round Metal Ductwork

Wire connectors.

Drywall plugs or other suitable wall fasteners based on your installation.

ACCESSORIES AVAILABLE

ACCESSORY SKU#

Activated Charcoal Filter Accessory Kit #FILTER1

Washable Long-Lasting Activated Charcoal Filter Kit #FILTER1LL

Internal 600 PRO Blower IB600 #IB600 kit

Internal 400 Blower IB400 #IB400 kit

Internal 300 Blower IB300 #IB300 kit

Remote Blower 900 RB900 (10” Flange Included) #RB900 kit

Remote Blower 1200 RB1200 (10” Flange Included) #RB1200 kit

10" Flange for In-Line Blower #FLANGE10

10

COMBINATIONS HOODS AND MOTOR KITS

RB900 kit and RB1200 kit

(remote blower)

FLANGE10

(In-Line Blower)

IB600 kit, IB400 kit, IB300 kit

(internal blower)

3B

4B

Discard 6" Flange

Discard 10" Flange

withWireBox

Discard Wire Cable

Version 07/11 - Page 6

INSTALLATION

COMBINATIONS HOOD AND MOTOR KITS

CHOOSE A BLOWER FOR YOUR HOOD

After choosing the hood width and depth for your cooking

needs, next choose the type of blower appropriate for

your cooking.

NOTE: no other blower is

compatible with this hood, except for the

kits below.

# IB300 - Internal Blower Kit 300 cfm

# IB600 - Internal Blower Kit 600 cfm

# IB1200 - Internal Blower Kit 1200 cfm

# RB900 - Remote Blower Kit 900 cfm

# RB1200 - Remote Blower Kit 1200 cfm

# INLBKIT - In Line Blower Kit

(supply own in-line blower)

OPTIONAL ACCESSORIES AVAILABLE

• *Charcoal Filter

* it is highly recommended that professional style cooking always be

vented to the outside; for recirculating installations only, some ductwork is

required to exhaust the unit out of the cabinet. Replace as needed with the

same model

part # FILTER1

NOTE: The charcoal ﬁlter kit for use with the 300 / 600

cfm internal blower kit ONLY

CAUTION - To reduce risk of ﬁre and electric shock, install this rangehood only with: Remote blower manufacturer by Faber

models RB900 and RB1200 or Integral blower manufactured by Faber models IB300 or IB600 or IB1200 or with INLBKIT and

generic in-line blower rated max 4.2 A suitable for use with solid state variable speed control

INLBKIT

1A

Keep

Keep 10" Flange

Blower

1B

Keep Blower

3A

2A

Keep 10" Flange

2A

11

Non Ducted - Recirculation Options

Ducted Venting Options

Activated Charcoal Filter Accessory FILTER1 or FILTER1LL required (Purchased separately).

Register cover for air duct exit is shown for design not included.

Attention: When used in recirculation mode, To Reduce the Risk of Fire and Shock use only conversion

kit Model FILTER1 or FILTER1LL.

6 "

A B

Register cover for air

duct exit is suggested.

CHOOSE YOUR DUCTING METHOD

Two men required for installation Wear work gloves for safety

Caution: If an elbow is required, do it as far away from the hood's exhaust opening as possible

6 "

Roof

Exterior

Wall

12

Open the lter cover panel. The lter cover panel

is held by a magnet catch, pull down with enough

force to release as shown below.

Remove the grease lters one at a time, pushing

them towards the back of the unit, and at the

same time pulling downward and set aside.

1

2

3

1 2

WIRING PREPARATION

WIRING BOX 1 for

connecting the Home

power supply cable

with the Hood.

WIRING BOX 2

for connecting the

External Blower with

the Hood.

1

2

HousePowerSupplyCableWiringBox1&RemoteBlowerWiringBox2

Choose wiring method based on blower type

13

3

Do not make any cutouts until you have decided whether this installation will be: ducted or non-ducted

and wiring has been prepared based on based on blower type.

CEILING HOOD INSTALL PREPARATION

Use a plumb line to mark the center of the

range on the ceiling.

Mark the centers.

4

5

DUE TO THE SIZE AND WEIGHT OF

THIS Range Hood, THE SUPPORT

MUST BE FIRMLY ATTACHED TO

THE CEILING. For plaster or sheet

rock ceiling, the support must be

attached to the joists. If this is not pos-

sible, a support structure must be built

behind the plaster or sheet rock. The

manufacturer assumes no responsibil-

ity for injury or damage caused by

improper installations.

WARNING

!

• For all installations, an access point to the hood must be created for installation and future maintenance

of the hood.

• Put a thick, protective covering over cooktop to protect from damage or dirt.

• Use the mounting template on the ceiling to determine placement of mounting screws on the ceiling.

• Mark the center of the holes in the ceiling template.

• Determine and make necessary cuts for the ductwork.

• Install ductwork before mounting the hood.

• Determine the proper location for the Power Supply Cable as indicated on the Template.

• Use a 1 1/4" Drill Bit to make this hole.

• Run the Power Supply Cable. Use caulking to seal around the hole.

• A knockout for threading through the Power Supply from the ceiling is located on the top of the Range

Hood.

• Do not connect the Power Cable to the Wiring Box or power up the hood at this time.

• Run enough power cable from the ceiling to reach the wiring box on the hood.

1 1/4"

H

14

CORRECT

NOT

CORRECT

In preparation for installation of the hood orient the hood with the control panel on the right as shown below

INSTALLATION INFORMATION

$[

 PP

[

15

1

3

Unfasten the 4 screws to dismount the

Box for the blower.

The blower can be positioned in four different venting directions as shown.

Rotate the Box with Blower in the correct position.

2

Position Internal Blower as shown into the

removed Blower Box. Secure the Internal

Blower in the Blower Box with the two screws

provided with the Internal Blower.

INTERNAL BLOWER INSTALLATION

Left

Right

Back

Front

Separate Box and Range Hood

Choose the Box position (Left-Right-Back-Front)

Attach the Internal Blower

Phillips ScrewdriverTorx Screwdriver

lfyouusetheinternalblowerkit,IB600kitorIB400kitorIB300kit,pleasethrowawaythetheange

(3B)andthecable(4B),givenwiththeinternalblowerkit,shownonpage10anduseonly10”Flange.

16

4

Attach the Box with the Blower with the same 4 screws removed previously.

After the blower is mounted

in the hood, plug the harness

with molex originating from the

control box, into the blower.

IMPORTANT: Do not use the

harness that came with your

internal blower kit (IB600 kit,

IB400 kit, IB300 kit).

IMPORTANT: Do not connect

the Control Cable to Wiring

Box 1 or Wiring Box 2 for

internal blower installation.

IMPORTANT: Do NOT use

wiring box 2 for an internal

blower installation.

5

Connect the cable to the Motor.

1

2

Connect the Electric Cable

Attach Motor Box to the Range Hood

Torx Screwdriver

17

1

2

Unfasten the 4 screws to dismount the Blower Box from the hood body and to save screws.

The Blower Box is not used for Remote Blower installation and can be discarded or saved for future

use if converted to Internal Blower.

Attach 10" FLANGE (2A) with 4 screws provided in

the hardware bag as shown.

lfyouusetheremoteblowerkit,RB900kitorRB1200kitorIn-LineBlowerOption,please

throwawaytheange(3A)givenwiththeremoteblowerkit,shownonpage10.

EXTERNAL BLOWER INSTALLATION

Separate the Box from the Range Hood

Attach optional FLANGE 10" (2A)

Torx Screwdriver

18

3

Connect the Hood body air outlet with the

Remote Blower air outlet.

4

Connect to Air Outlet

Connection to Box 2 (Remote Blower Wiring Box)

1

2

1. From inside the hood connect the cable

to the wiring box 2 as shown in the image

to the right.

2. From inside the hood, remove the cover from the

wiring box 2 by removing two screws.

3. Break the correct hole in the Wiring Box 2 for

passing the cables from the remote blower.

2

Box

19

INSTALLATION OF RANGE HOOD BODY

X = A - 5 1/16"

$

PP

; $PP

;

%[

5 1/16"

6

As shown, you have to

accommodate for the

height of the hood body

into your space overhead.

After determining bracket

height use the 8 Screws

from Component Page 8 to

assemble brackets.

$

PP

; $PP

;

%[

5

Min. 7 5/16"

Max. 12 13/16"

Option A

Steps 7a-7b-7c is an option for mounting and hood when access is available from above the ceiling/soft

(See page 20).

Option B

Steps 8a-8b-8c is an option for mounting the hood to the brackets when no access is available from above

and the soft is already completed (See page 22).

Choose the correct method of bracket installation

Assemble the Range Hood Mounting Brackets

Ref. Size Picture

G

1/8" x 3/8"

G

20

See below for a detailed image on

drilling the holes onto the fastening

surface (inside ceiling or soft) that

will then be used to mount the bracket

xtures.

The fasteners used must be compatible

with the 5/16" hole and are purchased

separately.

Ceiling Mark

7.a

OPTION A - HOOD INSTALLATION BEFORE THE SOFFIT IS COMPLETED

Use this installation if you have access from above to install the range hood

Bracket Installation on Ceiling

Use external holes created with drilling template for location of the ceiling fasteners (purchased separately).

Use wall plugs or other securing hardware in conjunction with the ceiling fasteners (purchased separately).

(1) Use a 5/16" Drill Bit to make these external hole.

(2) Use wall plugs if appropriate or other securing hardware in conjunction with the ceiling fasteners (purchased

separately).

(3) Use appropriate screws or other securing hardware in conjunction with the ceiling fasteners (purchased

separately) to attach the brackets.

7.b

 ´

[

³

´



1 2 3

La page charge ...

Faber Stratus 48 WH Guide d'installation

Ce manuel convient également à

Faber Stratus 48 WH Guide d'installation

dans d''autres langues

Documents connexes