Breville the Bambino Manuel utilisateur

EN

INSTRUCTION BOOK

FR-CA

MANUEL D'INSTRUCTIONS

ES-MX

MANUAL DE INSTRUCCIONES

the Bambino

™

2

BREVILLE

RECOMMENDS

SAFETY FIRST

At Breville we are very safety

conscious. We design and

manufacture consumer

products with the safety of you,

our valued customer, foremost

in mind. In addition, we ask

that you exercise a degree of

care when using any electrical

appliance and adhere to the

following precautions.

IMPORTANT

SAFEGUARDS

READ ALL INSTRUCTIONS

BEFORE USE AND SAVE

FOR FUTURE REFERENCE

• Carefully read all

instructions before

operating and save for

future reference.

• Do not touch hot

surfaces. Use handles or

knobs as advised in this

instruction book.

• To protect against ﬁre,

electric shock and injury to

persons do not immerse the

power cord, plug, or

appliance itself in water or

other liquids.

• Close supervision is

necessary when any

appliance is used by or

near children.

• Unplug from outlet when

not in use and before

cleaning. Allow to cool

before putting on or taking

off parts and before cleaning

the appliance.

2 Breville Recommends

Safety First

7 Components

9 Features

9 Assembly

10 Functions

15 Care & Cleaning

18 Troubleshooting

Contents

3

• It is recommended to

regularly inspect the

appliance and power cord.

Do not use the appliance if

there is damage to the

power cord or plug, or after

the appliance malfunctions

or has been damaged in

any way. Immediately stop

use and call Breville

Consumer Support.

• The use of accessory

attachments not

recommended by Breville

may result in ﬁre, electric

shock or injury to persons.

• Do not let the power cord

hang over the edge of a

table or counter-top or

touch hot surfaces.

• Do not place the appliance

near the edge of a table or

counter-top. Ensure the

surface is level, clean and

free of water and

other substances.

• Do not place the appliance

on or near a hot gas or

electric burner.

• Do not place it in or allow it

to come in contact with a

heated oven.

• This appliance is

recommended for

household use only. Do not

use this appliance for

anything other than its

intended use. Do not use

outdoors. Do not use in

moving vehicles or boats.

NOTICE TO CUSTOMERS

REGARDING MEMORY

STORAGE

• Please note that in order to

better serve our customers,

internal memory storage

has been imbedded into

your appliance. This

memory storage consists of

a small chip to collect

certain information about

your appliance including

the frequency of use of the

appliance and the manner

in which your appliance is

being used. In the event

your appliance is returned

for service, the information

collected from the chip

enables us to quickly and

efﬁciently service your

appliance. The information

collected also serves as a

4

valuable resource in

developing future

appliances to better serve

the needs of our

consumers. The chip does

not collect any information

regarding the individuals

who use the product or the

household where the

product is used. If you have

any questions regarding

the memory storage chip,

please contact us at

privacy@breville.com

SPECIFIC

INSTRUCTIONS FOR

BES450

• This appliance is

recommended for

household use only. Do not

use this appliance for other

than its intended use. Do

not use in moving vehicles

or boats. Do not use

outdoors. Misuse may

cause injury.

• If the appliance is to be:

−left unattended

−cleaned

−moved

−assembled; or

−stored,

always switch Off the

espresso machine by

simultaneously pressing

the 1 CUP and HOT

WATER buttons. Unplug

from the power outlet.

• Ensure the product is

properly assembled

before ﬁrst use.

• Do not use any other liquid

apart from cold mains/tap

water. We do not

recommend the use of

highly ﬁltered, de-

mineralized or distilled

water as this may affect the

taste of the coffee and how

the espresso machine is

designed to function.

• Do not leave the product

unattended when in use.

• Do not touch hot surfaces.

Allow the product to cool

down before moving or

cleaning any parts.

5

• Use caution when

operating the machine, as

metal surfaces are liable to

get hot during use.

WARNING

To avoid the risk of injury,

use caution when descaling,

as hot steam may be

released. Before descaling,

ensure drip tray is inserted.

Refer to ‘Care & Cleaning’

for further instructions.

Ensure the portaﬁlter is

ﬁrmly inserted and secured

into the group head before

starting the extraction.

Never remove the

portaﬁlter during the

brewing process.

WARNING

To avoid the risk of injury,

do not open the brew

chamber during the

brew process.

WARNING

Do not place portaﬁlter, the

tamper or any parts of the

appliance in the dishwasher.

WARNING

Do not immerse power

cord, power plug or any

parts of the appliance or

the appliance in water or

any other liquid.

WARNING

Misuse may cause injury.

SHORT CORD

INSTRUCTIONS

• Your Breville appliance is

ﬁtted with a short power

cord to reduce personal

injury or property damage

resulting from pulling,

tripping or becoming

entangled with a longer

cord. Longer detachable

power cords or extension

cords are available and

may be used if care is

exercised. If an extension

cord is used,

1. the marked electrical

rating of the cord set, or

extension cord should be

at least as great as the

electrical rating of

the appliance,

6

2. the cord should be

arranged so that it will

not drape over the

counter-top or table

where it can be pulled on

by children or tripped

over unintentionally and

3. the extension cord must

include a 3-prong

grounding plug.

BREVILLE ASSIST™

PLUG

• Your Breville appliance

comes with a unique

Assist™ Plug, conveniently

designed with a ﬁnger

hole to ease removal from

the power outlet.

FOR HOUSEHOLD USE ONLY

SAVE THESE INSTRUCTIONS

CSA DUTY CYCLE

MARKING

• The Canadian Standards

Authority requires any

appliances capable of

drawing over 1500W to

be marked with a ‘duty

cycle’ in minutes. For the

BES450, this ‘duty cycle’

represents the maximum

time for which the

appliance will draw over

1500W during any 2-hour

period of use. It does not

indicate the appliance is

unsafe for continuous use

or is required to be

switched off at certain

intervals

during normal use.

7

Components

A. 47 ﬂ.oz (1.4L) removable water tank

B. Control panel

1 CUP, 2 CUP, hot water, steam buttons

C. Group head

D. 54mm aluminum portaﬁlter

(WARNING: NOT dishwasher safe)

E. Steam wand grip

F. Steam wand

G. Removable drip tray grid

H. Removable drip with full indicator

A

B

C

H

D

F

E

G

8

ACCESSORIES

A. Stainless steel milk jug

B. 54mm tamper (Note: Do not submerge in

water or any liquid)

C. Steam wand tip cleaning tool

(Located under the water tank)

D. Dual wall ﬁlter baskets (1 cup & 2 cup)

E. Descaling powder

C

D

E

B

A

9

COMPACT FOOTPRINT

Cafe quality coffee in a compact machine.

MANUAL MILK TEXTURING

Manually textures milk from silky smooth latté

to creamy cappuccino.

THERMOJET ™ TECHNOLOGY

Innovative heating system achieves ideal

extraction temperature in 3 seconds.

PID TEMPERATURE CONTROL

Electronic PID temperature control for

increased temperature stability.

LOW PRESSURE PRE-INFUSION

Applies low water pressure at the start of the

extraction to gently expand grinds for an

even extraction.

VOLUMETRIC CONTROL

Preset 1 & 2 cup volumes, manual over-ride or

programmable shot volumes.

INSTANT HOT WATER

Hot water outlet via the steam wand for

making Americanos and pre-heating cups.

Bambino™

Features

Assembly

BEFORE FIRST USE

Machine Preparation

Remove and discard all labels and packaging

materials attached to your machine. Ensure

you have removed all parts and accessories

before discarding the packaging.

Clean the drip tray, drip tray grid, portaﬁlter,

ﬁlter baskets using warm water and a gentle

dish washing liquid. Rinse well and dry

thoroughly before use.

10

Functions

FIRST USE

1. Remove the water tank and ﬁll it with

potable water to the indicated MAX line.

Place the water tank back ﬁrmly onto

the machine.

2. Ensure that the drip tray is ﬁrmly placed on

the machine.

3. Place a 17 ﬂ. oz (500ml) container under

the portaﬁlter and steam wand for the water

drips for this ﬁrst cycle.

4. Plug the power cord in the power outlet, and

the 1 Cup button illuminates.

5. Press the 1 Cup button to begin the ﬁrst

use cycle.

NOTE

The ﬁrst use cycle is to rinse the machine and

prime the heating system.

STANDBY MODE

To turn off the operation and enter standby

mode, press the 1 Cup and Hot Water buttons

for 0.5 second simultaneously.

+

0.5s

NOTE

Unit will enter ‘standby mode’ when idle or no

interaction from user after 10 minutes.

FILLLING THE WATER TANK

Lift the water tank from the machine.

Remove the water tank lid and add potable

water to the water tank, ﬁlling to the MAX

marking indicated.

Replace the water tank onto the machine, press

down ensuring it is properly attached and

sitting ﬂush against the back of the machine.

NOTE

Machine LED lights will ﬂash 6 times for

3 seconds when no water is detected in

the water tank.

FILTER BASKETS

This machine includes dual wall 1 Cup

and 2 Cup ﬁlter baskets.

1 CUP 2 CUP

Use the 1 cup ﬁlter basket when brewing

a single cup and the 2 cup ﬁlter baskets

when brewing 2 cups or a stronger

single cup or mug.

You will need to adjust the grind amount and

size if switching from a single basket to a

double basket, or vice versa.

The provided ﬁlter baskets are designed for:

1 Cup ﬁlter basket = 8-11g

2 Cup ﬁlter basket = 16-19g

11

THE GRIND

When grinding coffee beans, the grind size

should be ﬁne but not too ﬁne. The grind size

will affect the rate at which the water ﬂows

through the ground coffee in the ﬁlter basket

and the taste of the espresso.

If the grind is too ﬁne (looks like powder and

feels like ﬂour when rubbed between the

ﬁngers), the water will not ﬂow through the

coffee even when under pressure. The resulting

espresso will be OVER EXTRACTED, dark in

color and bitter in ﬂavor.

If the grind is too coarse, the water will ﬂow

through the ground coffee in the ﬁlter basket too

quickly. The resulting espresso will be UNDER

EXTRACTED and lacking in color and ﬂavor.

COFFEE DOSE AND TAMPING

• Insert the ﬁlter basket into the portaﬁlter.

• Grind enough coffee to ﬁll the ﬁlter basket.

• Tap the portaﬁlter several times to collapse

and distribute the coffee evenly in the

ﬁlter basket.

• Using the tamper, tamp down ﬁrmly (approx.

30-40 lbs. (15-20kgs) of pressure). The

amount of pressure is not as important as the

consistent pressure every time.

As a guide, the top edge of the cap on the

tamper should be level with the top of the ﬁlter

basket AFTER the coffee has been tamped.

NOTE

We recommend quality 100% Arabica beans

with a ‘Roasted On’ date stamped on the bag,

not a ‘Best Before’ or ‘Use By’ date. Coffee

beans are best consumed between 5–20 days

after the ‘Roasted On’ date. Stale coffee may

pour too quickly from the portaﬁlter spouts

and taste bitter and watery.

PURGING THE GROUP HEAD

Before placing the portaﬁlter into the group

head, run a short ﬂow of water through the

group head by pressing the 1 Cup or 2 Cup

button. This will stabilize the temperature prior

to extraction.

INSERTING THE PORTAFILTER

Place the portaﬁlter underneath the group head

so that the handle is aligned with the INSERT

position. Insert the portaﬁlter into the group

head and rotate the handle towards the center

until resistance is felt.

LOCK

INSERT

Place your cup/s under the portaﬁlter on

the drip tray.

EXTRACTING ESPRESSO

As a guide the espresso will start to ﬂow after

8–10 seconds (infusion time) and should be the

consistency of dripping honey.

If the espresso starts to ﬂow after less than 6

seconds, either under dose the ﬁlter basket

or the grind is too coarse. This is an UNDER

EXTRACTED shot.

If the espresso starts to drip but doesn't ﬂow

after 15 seconds, the grind is too ﬁne. This is

an OVER EXTRACTED shot.

12

To set the 1 Cup volume:

• Press the 1 Cup button for about 3 seconds to

start the extraction.

• Press the 1 Cup button again to stop the

extraction. The modiﬁed volume will be saved.

To set the 2 Cup volume, follow the above steps

and select the 2 Cup button to start and stop

the extraction.

NOTES

• If no user input after 30 seconds. Machine

returns to ‘ready mode’

• The modiﬁed coffee volume will be saved into

memory for the next use or when the machine

is re-started.

• Pressing the steam or hot water button at

any stage will cancel the operation and the

machine will return to ready mode without

saving any coffee volume program.

MANUAL PRE-INFUSION AND SHOT

VOLUME

Press and hold the 1 Cup or 2 Cup button for

more than a second. After one second the pump

will start at pre-infusion pressure and continue

while button is pressed. Release the button to

start the extraction. Press any button again to

stop the extraction.

MANUAL MILK TEXTURING

• Lift the steam wand and insert into the milk

jug with the steam wand tip 3/4 inch (1-2cm)

below the surface of the milk, close to the right-

hand side of the jug at a 3 o’clock position.

PRE-PROGRAMMED SHOT VOLUME

- 1 CUP

Press the 1 Cup button for less than 1 second,

the button will ﬂash indicating that it has been

selected. A preset single espresso volume of

approximately 30ml will be extracted. The

machine will automatically stop once the

pre-set volume has been extracted.

PRE-PROGRAMMED SHOT VOLUME

- 2 CUP

Press the 2 Cup button for less than a second,

the button will ﬂash indicating that it has been

selected. A preset double espresso volume of

approximately 60ml will be extracted. The

machine will automatically stop once the

pre-set volume has been extracted.

NOTE

Pressing the corresponding 1 Cup or 2 Cup

button during the programmed espresso

extraction will immediately stop the extraction.

PROGRAMMING COFFEE VOLUME

Press and hold the 1 Cup and 2 Cup buttons for

2 seconds, the buttons will illuminate and ﬂash.

2s

+

OFF

13

• Press the STEAM button to begin texturing

• Keep the steam wand tip just under

the surface of the milk until the milk is

spinning clockwise, producing a vortex

(whirlpool effect).

• With the milk spinning, slowly lower the jug.

This will bring the steam wand tip to the

surface of the milk and start to introduce air

into the milk.

• Gently break the surface of the milk with the

tip to get the milk spinning fast enough.

• Keep the steam wand tip at or slightly below

the surface, continuing to maintain the vortex.

Texture the milk until sufﬁcient volume

is obtained.

• Lift the jug to lower the tip beneath the surface

but keep the vortex spinning. The milk is at

the correct temperature 140-149 F (60-65°C)

when the jug is hot to touch.

• When texturing is close to acceptable desired

result, press any button to stop texturing.

• After the steam is released completely, remove

the steam wand from the milk jug.

• Wipe the wand and tip with a

clean damp cloth.

STEAM WAND MANUAL PURGE

To reduce steam wand blockages, we

recommend running steam through the steam

wand after milk texturing. Lower and point

steam wand directly on drip tray and away from

users and press the steam button to run steam

to rinse steam wand, or press and hold steam

button for 3 seconds, to activate the steam wand

purge. This will run short water pulses through

the steam wand.

NOTE

Both 1 Cup and 2 Cup buttons will blink during

the steam purge function.

WARNING

After pressing steam button, the steam can’t

stop immediately, it needs a few seconds to

completely stop steam.

STEAM WAND BLOCKED

Regularly check steam performance. If the

steam wand is blocked, it will immediately stop

operating. See ‘Cleaning the Steam Wand’ for

further instructions.

HOT WATER OPERATON

Hot water through the steam wand

When machine is on ‘ready mode’, press hot

water button, and hot water ﬂow will start

through the steam wand. Press any button to

stop hot water ﬂow.

WARNING

Cup temperature is at 194°F (90°C). Be careful

in handling hot beverages.

14

EXTRACTION TIPS

A great espresso is about achieving the perfect balance between sweetness, acidity, and bitterness.

The ﬂavor of your coffee will depend on many factors, such as the type of coffee beans, degree of

roast freshness, coarseness or ﬁneness of the grind, dose of ground coffee and tamping pressure.

Experiment by adjusting these factors just one at a time to achieve the taste of your preference.

• Flow starts after 8–12 secs

• Flow slow like warm honey

• Crema is golden brown with a ﬁne

mousse texture

• Espresso is dark brown

SOLUTIONS SOLUTIONS

Tamp using 30-40 lbs

(15–20kg) of pressure.

The top edge of cap on

the tamper should be

level with the top of the

ﬁlter basket AFTER

tamping.

• Flow starts after 1–7 secs

• Flow fast like water

• Crema is thin and pale

• Espresso is pale brown

• Tastes bitter/sharp, weak and watery

• Flow starts after 13 secs

• Flow drips or not at all

• Crema is dark and spotty

• Espresso is very dark brown

• Tastes bitter and burnt

REMOVE USED

GRINDS

Used grinds will form

a coffee 'puck'. If the

puck is wet, refer to

the 'Under Extraction'

section.

RINSE FILTER

BASKET

Keep the ﬁlter basket

clean to prevent

blockages. Without

ground coffee in the ﬁlter

basket, lock the

portaﬁlter into the

machine and run hot

water through.

AFTER EXTRACTION

CORRECT EXTRACTION UNDER EXTRACTION OVER EXTRACTION

Tamp using 30-40 lbs

(15–20kg) of pressure.

The top edge of cap on

the tamper should be

level with the top of the

ﬁlter basket AFTER

tamping.

ALWAYS TAMP TO LINE

Adjust & re-test

ALWAYS TAMP TO LINE

Adjust & re-test

EXPERIMENT WITH GRIND:

• Grind needs to be ﬁner

for a slower extraction.

• Ensure you are controlling the dose.

Adjust & re-test

EXPERIMENT WITH GRIND:

• Grind needs to be coarser

for a faster extraction.

• Ensure you are controlling the dose.

Adjust & re-test

LOCK TIGHT

GRIND GRIND DOSE TAMP

OVER EXTRACTED

BITTER • ASTRINGENT

Too ﬁne Too much

Decrease dose

Too heavy

BALANCED

Optimum 8-11g (1 Cup)

16-19g (2 Cup)

30-40 lbs.

(15-20kgs)

UNDER EXTRACTED

UNDERDEVELOPED • SOUR

Too coarse Too little

Increase dose

Too light

15

Care & Cleaning

CLEAN & DESCALE CYCLE

The Bambino Espresso machine requires

regular cleaning and descaling and the

machine will ﬂag when it is expected for a

clean. The 2 Cup button will continuously

ﬂash; indicating machine will need cleaning

and descaling.

NOTE

Pressing any of buttons will cancel the alert

and return the machine to ready mode.

WARNING

It is NOT recommended to ignore the clean

cycle warning because after regular use, hard

water can cause mineral build-up in and on

many of the inner functioning components,

reducing the brewing ﬂow, brewing

temperature, power of the machine, and the

taste of the espresso.

WARNING

Do not immerse the power cord, power plug

or appliance in water or any other liquid.

The water tank should never be removed or

completely emptied during descaling.

TO PERFORM A CLEAN &

DESCALE CYCLE

1. Empty the drip tray and re-insert ﬁrmly into

position on the machine.

2. Fill the water tank to the DESCALE line

indicated and add the descaling agent

to the water.

DESCALE

1000

2L

68oz

3. Place a 2L / 68 ﬂ.oz container under the

group head and steam wand.

2L

68oz

DESCALE

1000

+

0.5s

5s

OR

&

2

L

68oz

MAX

4. Press the 2 Cup and Steam buttons

simultaneously for 5 seconds to

start descaling.

2L

68oz

DESCALE

1000

+

0.5s

5s

OR

&

2

L

68oz

MAX

NOTE

The 2-Cup button will ﬂash

throughout the cycle.

16

5. Once the descale solution has been used up,

the descale mode will pause.

6. Rinse and reﬁll the water tank to the MAX

line and empty the waste water container,

then replace both parts on to the machine to

proceed onto the rinse cycle.

7. Press the 2 Cup button to proceed

rinse cycle.

8. When the rinse cycle is complete, the

machine will then go into ready mode.

2L

68oz

DESCALE

1000

+

0.5s

5s

OR

&

2

L

68oz

MAX

9. Remove and empty the waste water

container. Rinse the drip tray and water tank

and dry thoroughly before replacing them

back onto the machine.

CLEANING THE STEAM WAND

• The steam wand should always be cleaned

after texturing milk. Wipe the steam wand

with a damp cloth.

• If any of the holes in the tip of the steam

wand become blocked, it may reduce frothing

performance. Manually purge the steam wand

to try and clear the holes.

• If the steam ﬂow is very small and steam wand

is still blocked, unscrew the steam wand tip

using the steam tip cleaning tool, then use

the tool to unblock the holes; cleaning tool

is located in the back of the machine, under

the water tank.

1

5

3 42

6 !

Rinse the steam tip and wipe with a clean, dry

cloth. Reassemble the steam wand by screwing

the steam tip back on to the steam wand. Purge

the steam wand after cleaning.

1

5

3 42

6 !

GROUP HEAD RINSE

• Press ‘2 Cup’ button to ﬂow freshwater

ﬂush cycle.

CLEANING THE FILTER BASKETS

AND PORTAFILTER

• The ﬁlter baskets and portaﬁlter should be

rinsed under hot water directly after use to

remove all residual coffee oils.

• If the holes in the ﬁlter baskets become

blocked, use the steam wand cleaning tool to

unblock the holes.

WARNING

Do not put portaﬁlter in dishwasher.

CLEANING THE SHOWER SCREEN

• The group head interior and shower screen

should be wiped with a damp cloth to remove

any ground coffee particles.

• Periodically run hot water through the

machine with the ﬁlter basket and portaﬁlter

in place, without any ground coffee, to rinse

out any residual coffee.

17

CLEANING THE DRIP TRAY

The drip tray should be removed, emptied and

cleaned after each use or when the drip tray

indicator rises through the drip tray grid.

Remove the drip tray grid and wash both parts

in warm soapy water.

CLEANING THE OUTER HOUSING

• Wipe the outer housing with a soft, damp

cloth and then polish with a soft, dry cloth.

NOTE

Do not use any abrasive cleaners, pads or

cloths which can scratch the surfaces of

the machine.

NOTE

Do not clean any of the parts or accessories in

the dishwasher.

WARNING

Do not immerse the power cord, power plug,

plastic tamp or machine in water or any

other liquid.

STORING YOUR MACHINE

Before storing, turn the machine off, switch off

and remove the power plug from the power

outlet. Empty the water tank and drip tray and

ensure the machine is cool, clean and dry. Store

in an upright position.

Do not place anything on top of machine.

RESET FACTORY ESPRESSO VOLUME

SETTINGS

1. When machine is on standby mode

2. Press and hold the 1 Cup and 2 Cup buttons

for 10 seconds to enter Factory reset mode.

3. The lights will ﬂash 3 times to indicate that

all volumes have been reset.

4. Machine will then return to ready mode.

NOTE

When machine is turned on after reset, it

enters directly to ready mode.

18

Troubleshooting

PROBLEM POSSIBLE CAUSES EASY SOLUTION

Water does not ﬂow from

the group head.

No hot water.

•

Water tank is empty.

•

Fill tank.

•

Water tank is not fully inserted and

locked into position.

•

Push water tank down completely to lock

into place.

•

Machine needs to be cleaned &

descaled.

•

Perform clean & descale cycle.

•

Coffee is ground too ﬁnely and/or too

much coffee in ﬁlter basket and/or over

tamping and/or ﬁlter basket is blocked.

•

See below, ‘Espresso only drips from the

•

portaﬁlter spouts or not at all’.

Espresso only drips

from the portaﬁlter

spouts or not at all.

•

Coffee is ground too ﬁnely.

•

Use slightly coarser grind. Refer to ‘Coffee

Dose and Tamping’ on page 11 and

‘Extraction Tips’ on page 14.

•

Too much coffee in the ﬁlter basket.

•

Lower dose of coffee.

•

Coffee tamped too ﬁrmly.

•

Tamp between 30-40 lbs (15-20kgs) of

pressure.

•

Water tank is empty. Fill tank.

•

Fill tank.

•

Water tank is not fully inserted and

locked into position.

•

Push water tank down completely to lock

into place.

•

The ﬁlter basket may be blocked.

•

Use the pin on the end of the provided

cleaning tool to unblock the hole(s).

•

Machine needs to be cleaned &

descaled.

•

Perform clean & descale cycle

Water doesn’t come

through (the machine

makes a loud noise).

•

Water tank is empty

•

Fill tank

Espresso runs out

too quickly

•

Coffee is ground too coarsely.

•

Use slightly ﬁner grind.

•

Refer to ‘Coffee Dose and Tamping’ on

page 11 and ‘Extraction Tips’ on page 14.

•

Not enough coffee in the ﬁlter basket.

•

Increase dose of coffee and tamp. Refer to

‘Coffee Dose and Tamping’ on page 11 and

‘Extraction Tips’ on page 14.

•

Coffee tamped too lightly.

•

Tamp between 30-40 lbs (15-20kgs) of

pressure.

Espresso runs out around

the edge of the portaﬁlter.

•

Portaﬁlter not inserted in the group

head correctly.

•

Ensure portaﬁlter is completely inserted

and rotated until resistance is felt.

•

There are coffee grounds around the

ﬁlter basket rim.

•

Clean excess coffee from the rim of the

ﬁlter basket to ensure a proper seal in group

head.

•

Too much coffee in the ﬁlter basket.

•

Lower dose of coffee. Refer to ‘Coffee Dose

and Tamping’, page 11

19

PROBLEM POSSIBLE CAUSES EASY SOLUTION

Small steam.

•

Machine has not reached operating

temperature.

•

Allow time for the machine to reach

operating temperature.

•

Water tank is empty.

•

Fill tank.

•

Water tank is not fully inserted and

locked into position.

•

Push water tank down completely to lock

into place.

•

Machine needs to be cleaned &

descaled.

•

Perform clean & descale cycle.

•

Steam wand is blocked or almost

blocked.

•

Refer to ‘Cleaning the Steam Wand’,

page 16.

Pulsing/pumping sound

while extracting espresso

or steaming milk.

•

The machine is carrying out the

normal operation of the pump.

•

No action required as this is the normal

operation of the machine.

•

Water tank is empty.

•

Fill tank.

Coffee not hot enough.

•

Portaﬁlter not pre-heated.

•

Rinse portaﬁlter under hot water outlet.

Dry thoroughly.

•

Run hot water through your cup to preheat

the cup.

No crema.

•

Coffee tamped too lightly.

•

Tamp between or 30-40 lbs. (15-20kgs) of

pressure.

•

Coffee is ground too coarsely.

•

Use slightly ﬁner grind. Refer to ‘Coffee

Dose and Tamping’ on page 11 and

‘Extraction Tips’ on page 14.

•

Coffee beans or pre-ground coffee are

not fresh.

•

If grinding fresh whole coffee beans,

use freshly roasted coffee beans with a

‘Roasted On’ date and consume between

5–20 days after that date. If using

pre-ground coffee, use within a week of

grinding.

•

The ﬁlter basket may be blocked.

•

Use the pin on the end of the provided

cleaning tool to unblock the hole(s).

Water leaking

•

Manual purge

•

Water tank is not fully inserted and

locked into position.

•

Turn the steam wand directly on the drip

tray or jug before manual purge.

•

Push water tank down completely to lock

into place.

Machine is on but

ceases to operate.

•

The safety thermal-cut out may

have activated due to the pump

overheating.

•

Press the 1 CUP and HOT WATER

buttons simultaneously for 0.5 seconds to

switch the machine off and unplug from

the power outlet. Allow to cool for about

30–60 minutes. If problem persists, call

Breville Support.

Too much/too little

espresso is being

delivered to the cup.

•

Grind amount and/or grind size

settings and/or shot volumes require

adjustment.

•

Adjust the grind amount and/or grind

size settings. Refer to ‘Coffee Dose and

Tamping’, page 11, ‘The Grind’, page 11 and

‘Extraction Tips’, page 14.

20

Notes

La page charge ...

Breville the Bambino Manuel utilisateur

Breville the Bambino Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents