Sub Zero PRO4850G Guide d'installation

PRO REFRIGERATION

INSTALLATION GUIDE

SPECIFICATIONS, INSTALLATION, AND MORE

2 | Sub-Zero Customer Care 800.222.7820

PRO REFRIGERATION

Contents

3 PRO Refrigeration

4 Opening Dimensions

6 Electrical

6 Plumbing

7 Preparation

8 Anti-Tip Bracket

10 Placement

10 Water Line

11 Alignment

13 Completion

Features and specications are subject to change at any

time without notice. Visit subzero.com/specs for the most

up-to-date information.

Important Note

To ensure this product is installed and operated as safely

and efciently as possible, take note of the following types

of highlighted information throughout this guide:

IMPORTANT NOTE highlights information that is especially

important.

CAUTION indicates a situation where minor injury or product

damage may occur if instructions are not followed.

WARNING states a hazard that may cause serious injury or

death if precautions are not followed.

IMPORTANT NOTE: Throughout this guide, dimensions in

parentheses are millimeters unless otherwise specied.

IMPORTANT NOTE: Save these instructions for the local

electrical inspector.

subzero.com | 3

Product Information

Important product information, including the model and

serial number, are listed on the product rating plate. The

rating plate is located inside the cabinet, attached to the left

interior wall of the bottom drawer. Refer to the illustration

below.

If service is necessary, contact Sub-Zero Factory Certied

Service with the model and serial number. For the name

of the nearest Sub-Zero Factory Certied Service or for

questions regarding the installation, visit the contact

and support section of our website, subzero.com, or call

Sub-Zero Customer Care at 800-222-7820.

PRO REFRIGERATION

Tools and Materials

• Screwdrivers—standard, Phillips, Torx, and hex.

• Power drill.

• Drill bits (masonry bits required for concrete installation).

• Standard Allen wrench set.

• Standard socket and wrench set.

• 2' and 4' levels.

• Tubing cutter.

• 3' of

1

/4" OD copper, braided stainless steel, or PEX

tubing.

• Saddle valve.

• Material to protect home, ooring, and cabinetry during

installation.

RATING

PLATE

Rating plate location

4 | Sub-Zero Customer Care 800.222.7820

SITE PREPARATION

Opening Dimensions

STANDARD | FLUSH INSTALLATION

NOTE:

3

1

/2" (89) finished returns will be visible and should be finished to match cabinetry.

H

OPENING

HEIGHT

D

OPENING

DEPTH

FRONT VIEW

SIDE

VIEW

TOP VIEW

W

OPENING WIDTH

3

/4" (19)

TYPICAL

FRAMED

CABINETRY

W

FILLER

3

1

/2" (89)

FINISHED

RETURN

FRAMELESS

CABINETRY

W

3

/4" (19)

TYPICAL

3

1

/2" (89)

FINISHED

RETURN

STANDARD OPENING W

H D

36" Model 35

1

/2" (902) 83

3

/4" (2127) 24" (610)

48" Model 47

1

/2" (1206) 83

3

/4" (2127) 24" (610)

For standard installations, the face frame will extend 2" (51)

beyond cabinetry.

FLUSH OPENING

W H D

36" Model 36" (914) 84

1

/8" (2137) 26" (660)

48" Model 48" (1219) 84

1

/8" (2137) 26" (660)

For ush installations, the face frame will be ush with sur-

rounding cabinetry.

subzero.com | 5

Opening Dimensions

DUAL STANDARD | FLUSH INSTALLATION

NOTE:

3

1

/2" (89) finished returns will be visible and should be finished to match cabinetry.

H

OPENING

HEIGHT

D

OPENING

DEPTH

FRONT VIEW

SIDE

VIEW

TOP VIEW

W

OPENING WIDTH

3

/4" (19)

TYPICAL

FRAMED

CABINETRY

W

FILLER

3

1

/2" (89)

FINISHED

RETURN

FRAMELESS

CABINETRY

W

3

/4" (19)

TYPICAL

3

1

/2" (89)

FINISHED

RETURN

DUAL STANDARD OPENING W

H D

Two 36" Models 71

1

/2" (1816) 83

3

/4" (2127) 24" (610)

For standard installations, the face frame will extend 2" (51)

beyond cabinetry. A dual installation kit is required for this

installation.

DUAL FLUSH OPENING

W H D

Two 36" Models 72" (1829) 84

1

/8" (2137) 26" (660)

For ush installations, the face frame will be ush with sur-

rounding cabinetry. A dual installation kit is required for this

installation.

SITE PREPARATION

6 | Sub-Zero Customer Care 800.222.7820

SITE PREPARATION

Electrical Requirements

Installation must comply with all applicable electrical codes.

Locate the electrical supply within the shaded area shown

in the illustration below. A separate circuit servicing only

this appliance is required. A ground fault circuit interrupter

(GFCI) is not recommended and may cause interruption of

operation.

ELECTRICAL REQUIREMENTS

Electrical Supply 115 VAC, 60 Hz

Service 15 amp dedicated circuit

Receptacle 3-prong grounding-type

CAUTION

The outlet must be checked by a qualied electrician

to be sure it is wired with the correct polarity. Verify the

outlet is properly grounded.

WARNING

Do not locate multiple portable socket-outlets, power

strip, or portable power supplies at the rear of the

appliance.

WARNING

Do not use an extension cord, two-prong adapter, or

remove the power cord ground prong.

Plumbing Requirements

Installation must comply with all applicable plumbing codes.

Locate the water supply line within the shaded area shown

in the illustration below. Connect the water supply line to the

house supply with an easily accessible shut-off valve. Do

not use self-piercing valves. The water supply line must not

interfere with the installation of the anti-tip bracket.

A reverse osmosis system can be used provided there is

constant water pressure of 35–120 psi

(2.4–8.3 bar) supplied

to the unit at all times. In this application, the water ltration

system must be bypassed by removing the lter. A copper

line is not recommended for this application.

PLUMBING REQUIREMENTS

Water Supply

1

/4" OD copper, braided

stainless steel, or PEX tubing

Pressure 35–120 psi

(2.4–8.3 bar)

Excess Line for Connection 36" (914)

75

1

/2" (1918)

FROM FLOOR

7"

(178)

E

6"

(152)

RIGHT SIDE

OF OPENING

Electrical supply location

3" (76)

6"

(152)

5

3

/16"

(132)

RIGHT SIDE

OF OPENING

AREA EXTENDS

1

/2" (13)

FORWARD ON FLOOR

Water supply location

subzero.com | 7

Preparation

Uncrate the unit, and inspect for damage. Remove the wood

base, and discard the shipping bolts and brackets. Remove

and recycle packing materials. Do not discard the kickplate,

anti-tip bracket, and hardware.

Completely retract the front leveling legs to allow the unit to

be moved into position. The front and rear leveling legs can

be adjusted from the front once the unit is in position.

Remove the drain pan from the base of the unit to avoid

damage and to allow for proper placement of the appliance

dolly.

The grille assembly should be removed prior to moving

the unit. To remove, rotate the bottom of the grille upward.

Disconnect the network cable, then remove the center

mounting screw. Loosen the three grille bolts from the grille,

then pull the grille forward. Refer to the illustrations below.

Lift grille

Grille removal

BOLT

CONNECTOR

SCREW

SITE PREPARATION

Doors and drawers can be removed for ease of installation.

Door and drawer removal is not required. To remove a door,

refer to the illustration below. To remove a drawer, pull the

drawer out to full-extension. Apply forward pressure to

the front of the drawer slide, and pull up and back on the

drawer handle. Refer to the illustration below.

DRAWER

SLIDE

Door removal

Drawer removal

8 | Sub-Zero Customer Care 800.222.7820

Anti-Tip Bracket

WARNING

To prevent the unit from tipping forward, the anti-tip

bracket must be installed.

Use the centerline locating holes to position the anti-tip

bracket in the center of the opening. The bracket must be

positioned 24"

(610) from the front of the opening to the

back of the bracket. This depth will increase to 26"

(660) for

a ush installation. Failure to properly position the anti-tip

bracket will prevent proper engagement.

Use all anti-tip bracket hardware as instructed for wood or

concrete oors.

IMPORTANT NOTE: For wood or concrete oor applications,

if the #12 screws do not hit a wall stud or wall plate, use the

#8 screws and #12 washers with the wall anchors.

IMPORTANT NOTE: In some installations the subooring or

nished oor may necessitate angling the screws used to

fasten the anti-tip bracket to the back wall.

ANTI-TIP HARDWARE

1 Anti-tip bracket

12 #12 x 2

1

/2" pan head screws

3

/8"–16 x 3

3

/4" wedge anchors

12 #12 at washers

3 #8–18 x 1

1

/4" truss head screws

3 Nylon Zip-it

®

wall anchors

CENTERLINE

LOCATING HOLES

Anti-tip bracket

INSTALLATION

WOOD FLOOR APPLICATION

After properly locating the anti-tip bracket in the opening,

drill pilot holes

3

/16" (5) diameter maximum in the wall studs

or wall plate. Use the #12 screws and washers to secure

the bracket. Verify the screws penetrate through the ooring

material and into the wall studs or wall plate a minimum of

3

/4" (19). Refer to the chart and illustration below.

CONCRETE FLOOR APPLICATION

After properly locating the anti-tip bracket in the opening,

drill pilot holes

3

/16" (5) diameter maximum in the wall studs

or wall plate. Drill

3

/8" (10) diameter holes into the concrete

a minimum of 1

1

/2" (38) deep. Use the #12 screws and

washers to secure the bracket to the wall, and use the

3

/8"

wedge anchors to secure the bracket to the oor. Verify the

screws penetrate the wall studs or wall plate a minimum of

3

/4" (19). Refer to the chart and illustration below.

ANTI-TIP BRACKET PLACEMENT

A

36" Model 17

3

/4" (451)

48" Model 23

3

/4" (603)

A

SUBFLOORING

WOOD FLOOR

WALL PLATE

FINISHED

FLOORING

A

SUBFLOORING

CONCRETE

FLOOR

WALL PLATE

FINISHED

FLOORING

1

/2"(38)

min

Wood oor

Concrete oor

subzero.com | 9

Anti-Tip Bracket

CONCRETE WEDGE ANCHOR INSTALLATION

1 Drill a

3

/8" (10) diameter hole any depth exceeding the

minimum embedment. Clean the hole or drill additional

depth to accommodate the drill nes.

2 Assemble the washer and nut ush with the end of

anchor to protect threads. Drive the anchor through the

material to be fastened until the washer is ush with the

surface material.

3 Expand the anchor by tightening the nut 3–5 turns past

hand-tight position or to 25 foot-pounds of torque.

WARNING

Verify there are no electrical wires or plumbing in the

area which the screws could penetrate.

CAUTION

Always wear safety glasses and use other necessary

protective devices or apparel when installing or working

with anchors.

Anchors are not recommended for use in lightweight

masonry material such as block or brick, or for use in

new concrete which has not had sufcient time to cure.

The use of core drills is not recommended to drill holes

for the anchors.

INSTALLATION

10 | Sub-Zero Customer Care 800.222.7820

Water Line

Approximately 3' (.9 m) of

1

/4" plastic tubing is connected to

the unit with a preassembled

1

/4" compression connection

under the unit. The water line tting connection kit, provided

with the unit, contains a

1

/4" compression union tting for

connection to the household water line.

Purge the water line prior to nal connection to the unit. This

will remove any debris that may be present in the tubing

from installing the new water line.

Place the sleeve and nut on the water line, and fasten to the

connection at the end of the tubing. Do not over tighten.

Check all water line ttings for leaks. Verify the drain pan

can be installed and removed without interference with the

water line.

IMPORTANT NOTE: If a reverse osmosis system is used, it

is recommended the water ltration system be bypassed by

removing the lter.

IMPORTANT NOTE: Water lines cannot be exposed to

freezing temperatures.

WARNING

Connect to potable water supply only.

INSTALLATION

Placement

CAUTION

Before moving the unit into position, secure doors and

drawers closed, and protect any nished ooring.

WARNING

When positioning the appliance, ensure the supply

cord is not trapped or damaged.

Use an appliance dolly to move the unit near the opening.

If the unit has been on its back or side, it must stand upright

for a minimum of 24 hours before connecting power.

Plug the power cord into the grounded outlet, and roll the

unit into position. Verify the anti-tip bracket is properly

engaged.

subzero.com | 11

Alignment

LEVELING

Once the unit is in position, turn the front leveling legs

clockwise to adjust the height. The rear height adjustment

can be made from the front of the roller base. Using a

3

/8"

socket, turn the

3

/8" hex bolt clockwise to raise the unit or

counterclockwise to lower. Use the lowest torque setting

when using a power drill. Do not turn the rear leveling legs

by hand. Refer to the illustration below.

When the unit is properly leveled, door and drawer adjust-

ments are less likely to be necessary.

IMPORTANT NOTE: Level the unit to the oor, not the sur-

rounding cabinetry. This could affect the operation of the

unit, such as door closing.

INSTALLATION

FRONT

LEVELING LEG

REAR

ADJUSTMENT

Leveling

WARNING

To reduce the possibility of the unit tipping forward, the

front leveling legs must be in contact with the oor.

12 | Sub-Zero Customer Care 800.222.7820

INSTALLATION

Side-to-Side Adjustment:

1 Loosen the two mounting screws on the upper and/or

lower cabinet hinge. Refer to the illustration below.

2 Use the Allen wrench provided to rotate the adjustment

screw.

3 Verify the hinge is parallel to the side of the unit, then

tighten the mounting screws.

4 Install the hinge pins and door, then verify the door

alignment.

Alignment

DOOR ADJUSTMENT

The doors are adjustable in and out, up and down, and side

to side. In-and-out and up-and-down adjustments are made

on the door. Side-to-side adjustments are made on the

cabinet hinges. To make any adjustments, remove the door

and hinge pins. Refer to the illustration below.

In-and-Out and Up-and-Down Adjustment:

1 Place the door on a protected work surface, then loosen

the two upper hinge mounting screws.

2 Remove the two lower hinge mounting screws, then

remove the lower hinge.

3 Remove the positioning screw from the bottom of the

door, then use the adjustment pin to make up-and-down

and in-and-out adjustments. Refer to the illustration

below. Each vertical hole location adjusts the door

1

/32"

(1)

. The slotted holes allow for in-and-out adjustment.

4 Once the adjustments are made, install and tighten the

positioning screw.

HINGE

ADJUSTMENT

DOOR HINGE

POSITIONING

SCREW

Door removal

Door adjustment

HINGE

SCREW

ADJUSTMENT

SCREW

Cabinet hinge adjustment

subzero.com | 13

Alignment

DRAWER ADJUSTMENT

Up-and-Down Adjustment:

1 Use a hex wrench to turn the up-and-down adjustment

screw counterclockwise to raise and clockwise to lower.

Refer to the illustration below.

Side-to-Side Adjustment:

1 Use a hex wrench to turn the adjustment screw. Refer to

the illustration below.

2 Both drawer slides must be adjusted equally to achieve

movement. For example, if the right slide adjustment

screw rotated clockwise, rotate the left slide screw

equally counterclockwise.

Tilt Adjustment:

1 Loosen the side and the bottom, center screws. Refer to

the illustration below.

2 Remove the screw from the corner of the drawer that is

out of adjustment.

3 Move the drawer front in or out by hand.

4 Install the screw into the bottom of the drawer. Each hole

location adjusts the door in or out by

1

/32" (1).

5 Tighten the side and bottom, center screws.

Completion

ANCHORING

After the unit has been leveled and door and drawer adjust-

ment completed, anchor the unit to the opening to ensure a

proper t and secure installation.

To Anchor the Unit:

1 Loosen the mounting bracket screws at the top of the

unit, then slide the mounting brackets to the side until

they contact the sides of the opening. Install additional

blocking if necessary. Refer to the illustration below.

2 Secure the brackets with the anchoring screws provided,

then tighten the mounting bracket screws.

SIDE-TO-SIDE

ADJUSTMENT

UP-AND-DOWN

ADJUSTMENT

LOOSEN

REMOVE

Drawer adjustment

Drawer tilt adjustment

INSTALLATION

ANCHORING

SCREWS

BRACKET SCREWS

Anchoring

14 | Sub-Zero Customer Care 800.222.7820

INSTALLATION

WATER FILTER BYPASS

If the water ltration system will not be used, it can be

bypassed by removing the water lter.

To Remove the Water Filter:

1 To access the water lter, rotate the bottom of the grille

upward.

2 To remove the lter, rotate counterclockwise one-quarter

turn, then pull out. Refer to the illustration below.

Water lter removal

WATER FILTER

Completion

Install the grille assembly and check for proper t. Recon-

nect the network cable. Refer to page 6. Attach the network

cable to the grille using the cable ties provided.

Reinstall the drain pan and verify it is in the proper position.

Install the kickplate using the screws to attach it to the

brackets on the inside of each roller base. Refer to the illus-

tration below. The kickplate must be removable for service.

The oor cannot interfere with removal.

Install the leg covers.

For initial start up, touch and hold

POWER on either

external touch display, located on the grille.

Kickplate installation

subzero.com | 15

Sub-Zero, Sub-Zero & Design, Sub-Zero & Snowake Design, Dual Refrigeration, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, Wolf, Wolf &

Design, Wolf Gourmet, W & Design, red colored knobs, Cove, and Cove & Design are registered trademarks and service marks of Sub-Zero Group, Inc. and its subsidiaries.

All other trademarks are property of their respective owners in the United States and other countries.

Completion

90° DOOR STOP

The door(s) of all models open to 135°. For installations

where the door opening must be limited, an optional 90°

door stop kit is available through an authorized Sub-Zero

dealer. For local dealer information, visit the nd a show-

room section of our website, subzero.com.

INSTALLATION

WARNING

Follow all city and state laws when storing, recycling,

or discarding unused refrigerators and freezers.

2 | Sub-Zero Customer Care 800.222.7820

REFRIGERACIÓN PRO

Contenido

3 Refrigeración PRO

4 Dimensiones de la apertura

6 Instalación eléctrica

6 Plomería

7 Preparación

8 Soporte antivuelco

10 Colocación

10 Línea de agua

11 Alineación

13 Finalización

Las características y especicaciones están sujetas a

cambios sin previo aviso. Visite subzero.com/specs para

obtener la información más actualizada.

Aviso importante

Para garantizar que este producto se instale y opere de

la forma más segura y eciente posible, tome nota de los

siguientes tipos de información resaltada en esta guía:

AVISO IMPORTANTE señala la información que es

especialmente importante.

PRECAUCIÓN indica una situación en la que se pueden

sufrir heridas leves o provocar daños al producto si no se

siguen las instrucciones.

ADVERTENCIA indica peligro de que se produzcan heridas

graves o incluso la muerte si no se siguen las precauciones.

AVISO IMPORTANTE: En toda esta guía, las dimensiones

entre paréntesis son milímetros, a menos que se especique

lo contrario.

AVISO IMPORTANTE: guarde estas instrucciones para el

inspector eléctrico local.

subzero.com | 3

Información del producto

La información importante del producto, incluidos el modelo

y el número de serie de la unidad, se encuentra en la placa

de datos del producto. La placa de datos está situada

dentro del gabinete, unida a la pared interior izquierda de la

parte inferior del cajón. Consulte la siguiente ilustración.

Si necesita servicio, póngase en contacto con el centro

de servicio autorizado de Sub-Zero y tenga a la mano el

modelo y número de serie de la máquina. Para obtener los

datos del centro de servicio autorizado de Sub-Zero más

cercano o si tiene preguntas acerca de la instalación, visite

la sección de contacto y soporte técnico en nuestra página

de Internet subzero.com o llame a la línea de atención al

cliente de Sub-Zero al 800-222-7820.

REFRIGERACIÓN PRO

Herramientas y materiales

• Destornilladores: estándar, Phillips, Torx y hexagonales.

• Taladro eléctrico.

• Brocas (se requieren brocas de mampostería para

instalación en concreto).

• Juego de llaves Allen estándar.

• Juego de llaves y vaso estándar.

• Niveles 2' y 4'.

• Cortador de tubos.

• 3' de tubería de cobre, trenzada de acero inoxidable o

PEX de

1

/4" de diámetro exterior.

• Válvula de asiento.

• Material para proteger la casa, el piso y los gabinetes

durante la instalación.

PLACA DE

DATOS

Ubicación de la placa de datos

4 | Sub-Zero Customer Care 800.222.7820

PREPARACIÓN DEL SITIO

Dimensiones de abertura

INSTALACIÓN EMPOTRABLE | ESTÁNDAR

NOTA: Los tubos de retorno de

3

1

/2" (89) con acabados se podrán ver y se deben terminar para que se ajusten a los gabinetes.

H

ALTURA DE

LA ABERTURA

D

PROFUNDIDAD DE

LA ABERTURA

VISTA FRONTAL

VIST

A LATERAL

VISTA SUPERIOR

W

ANCHO DE LA ABERTURA

TÍPICO DE

3

/4" (19)

GABINETE

CON MARCO

W

RELLENO

TUBO DE

RETORNO DE

3

1

/2" (89) CON

ACABADOS

GABINETES

SIN MARCO

W

TÍPICO DE

3

/4" (19)

TUBO DE

RETORNO DE

3

1

/2" (89) CON

ACABADOS

ABERTURA

ESTÁNDAR

W H D

Modelo de 36" 35

1

/2" (902) 83

3

/4" (2127) 24" (610)

Modelo de 48" 47

1

/2" (1206) 83

3

/4" (2127) 24" (610)

En las instalaciones estándar, el marco frontal se extenderá

2"

(51) más allá de los gabinetes.

ABERTURA

EMPOTRABLE

W H D

Modelo de 36" 36" (914) 84

1

/8" (2137) 26" (660)

Modelo de 48" 48" (1219) 84

1

/8" (2137) 26" (660)

Para las instalaciones empotrables, el marco frontal se

instalará con los gabinetes que lo rodean.

subzero.com | 5

Dimensiones de abertura

INSTALACIÓN EMPOTRABLE | ESTÁNDAR DOBLE

NOTA: Los tubos de retorno de

3

1

/2" (89) con acabados se podrán ver y se deben terminar para que se ajusten a los gabinetes.

H

ALTURA DE

LA ABERTURA

D

PROFUNDIDAD DE

LA ABERTURA

VISTA FRONTAL

VIST

A LATERAL

VISTA SUPERIOR

W

ANCHO DE LA ABERTURA

TÍPICO DE

3

/4" (19)

GABINETE

CON MARCO

W

FILLER

TUBO DE

RETORNO DE

3

1

/2" (89) CON

ACABADOS

GABINETES

SIN MARCO

W

TÍPICO DE

3

/4" (19)

TUBO DE

RETORNO DE

3

1

/2" (89) CON

ACABADOS

ABERTURA

ESTÁNDAR DOBLE

W H D

Dos modelos de 36" 71

1

/2" (1816) 83

3

/4" (2127) 24" (610)

En las instalaciones estándar, el marco frontal se extenderá

2"

(51) más allá de los gabinetes. Para esta instalación se

requiere un kit de instalación doble.

ABERTURA

EMPOTRABLE DOBLE

W H D

Dos modelos de 36" 72" (1829) 84

1

/8" (2137) 26" (660)

Para las instalaciones empotrables, el marco frontal se

instalará con los gabinetes que lo rodean. Para esta

instalación se requiere un kit de instalación doble.

PREPARACIÓN DEL SITIO

6 | Sub-Zero Customer Care 800.222.7820

PREPARACIÓN DEL SITIO

Requisitos eléctricos

La instalación debe cumplir con todos los códigos

eléctricos vigentes. El suministro eléctrico debe colocarse

dentro del área sombreada que se muestra en la siguiente

ilustración. Se necesita un circuito independiente que le

suministre electricidad únicamente a este electrodoméstico.

No es recomendable utilizar un circuito de fallos de

conexión a tierra (GFCI, por sus siglas en inglés) ya que

puede interrumpir el funcionamiento de la unidad.

REQUISITOS ELÉCTRICOS

Suministro eléctrico 115 V CA, 60 Hz

Servicio Circuito dedicado de 15 amperes

Receptáculo Conexión a tierra de 3 clavijas

PRECAUCIÓN

Un electricista calicado debe revisar el tomacorriente

para asegurarse de que la conexión del cableado se

haya realizado con la polaridad correcta. Verique que

el tomacorriente esté debidamente conectado a tierra.

ADVERTENCIA

No ubique múltiples tomacorrientes, tomas de cor-

riente o fuentes de alimentación portátiles en la parte

posterior del dispositivo. No use un cable de exten-

sión, adaptador de dos clavijas ni retire la clavija con

conexión a tierra del cable de corriente.

Requisitos de plomería

La instalación debe cumplir con todos los códigos de

plomería vigentes.

La línea del suministro de agua debe colocarse dentro del

área sombreada que se muestra en la siguiente ilustración.

La tubería del suministro de agua debe conectarse al

suministro doméstico con una válvula de cierre de fácil

acceso. No use válvulas autoperforantes. La línea del

suministro de agua no debe interferir en la instalación del

soporte antivuelco.

Se puede utilizar un sistema de ósmosis inversa siempre

y cuando la presión del agua que llegue a la unidad se

mantenga de forma constante entre 35 y 120 psi

(de 2.4a

8.3bares)

en todo momento. En esta aplicación, se debe

desviar el sistema de ltrado de agua mediante la extracción

del ltro. No es recomendable usar tuberías de cobre para

esta aplicación.

REQUISITOS DE PLOMERÍA

Suministro de agua: Tubería de cobre, trenzada de

acero inoxidable o PEX de

1

/4" de diámetro exterior

Presión De 35 a 120 psi

(de 2.4 a 8.3bares)

Tubería de exceso para la conexión 36" (914)

75

1

/2" (1918)

DESDE EL SUELO

7"

(178)

E

6"

(152)

LADO DERECHO

DE LA ABERTURA

Ubicación del suministro

eléctrico

3" (76)

6"

(152)

5

3

/16"

(132)

LADO DERECHO

DE LA ABERTURA

EL ÁREA SE EXTIENDE

1

/2" (13) EN EL SUELO

Ubicación del suministro de agua

La page charge ...

Sub Zero PRO4850G Guide d'installation

Sub Zero PRO4850G Guide d'installation

dans d''autres langues

Documents connexes

Autres documents