DATA ROBOTICS DROBOPRO FS Le manuel du propriétaire

User Guide

Drobo FS and DroboPro FS

User Guide

Note

EN Please check the following website for the most up to date

Drobo User Guide.

www.drobo.com/support

DE Bitte sehen Sie auf der unten aufgeführte webseite nach für

die Drobo Gebrauchsanweisung in Ihrer Sprache.

www.drobo.com/support/intl

ES Por favor consulte el siguiente sitio de web para localizar el

Drobo guia de usuario en su idioma.

www.drobo.com/support/intl

FR Veuillez voir le site Web ci-dessous pour le manuel d’utilisateur

de Drobo dans votre langue.

www.drobo.com/support/intl

IT Si prega di consultare il sito web sotto per la Drobo Guida

utente nella vostre lingua.

www.drobo.com/support/intl

日本語次のウェブサイトで、Drobo ユーザーガイドの最新更新

最新更新日付をチェックしてください。

www.drobo.com/support/intl

Contents

I. Introduction ........................................................................................ 1

II. Getting started ................................................................................... 3

Three easy steps ........................................................................................ 3

Selecting hard drives .................................................................................. 3

Choosing capacity ................................................................................... 4

Keeping your product up-to-date .............................................................. 4

Safe Shutdown of your FS array ................................................................. 4

Saving Power .............................................................................................. 5

What to do when not using your FS storage array .................................... 5

Online Resources and Assistance ............................................................... 6

Best Practices ............................................................................................. 6

III. Drobo FS Setup ................................................................................... 7

Install Drobo Dashboard ............................................................................ 7

Inserting drives into Drobo FS .................................................................... 7

Connect Drobo FS to your network ........................................................... 8

Ethernet .................................................................................................. 8

Connect power ........................................................................................... 8

Initialize your Drobo FS .............................................................................. 9

Drobo FS Lights ........................................................................................ 10

IV. DroboPro FS Setup ........................................................................... 11

Install Drobo Dashboard .......................................................................... 11

Inserting drives into your DroboPro FS .................................................... 11

Connect DroboPro FS to your network .................................................... 12

Ethernet ................................................................................................ 12

Connect power ......................................................................................... 12

Initialize your DroboPro FS ...................................................................... 13

DroboPro FS Lights ................................................................................... 14

V. Using Drobo Dashboard with your FS array ..................................... 15

Drobo Dashboard basics .......................................................................... 15

The main page ....................................................................................... 15

Advanced Controls: Data tab ................................................................ 17

Advanced Controls: Tools tab ............................................................... 18

Drobo FS and DroboPro FS Settings ......................................................... 19

General Tab ........................................................................................... 19

Drobo FS ................................................................................................ 19

DroboPro FS .......................................................................................... 20

Dual disk redundancy ............................................................................ 20

Disk drive spin down ............................................................................. 21

Dimming the Indicator lights (Drobo FS only) ....................................... 21

Network Tab .......................................................................................... 21

Network Mode (DroboPro FS only) ....................................................... 22

Admin Tab ............................................................................................. 24

Shares Tab ............................................................................................. 24

Time Machine – Mac OS X .................................................................... 27

Alerts Tab .............................................................................................. 29

Additional features .................................................................................. 29

DroboCopy ............................................................................................ 30

DroboApps ............................................................................................ 30

Keeping Drobo Dashboard up-to-date .................................................. 30

Accessing files on your FS storage array .................................................. 31

VI. Tips and Troubleshooting ................................................................. 34

VII. Index ................................................................................................. 40

1

I. Introduction

Thank you for giving another Drobo® storage device a good home! We

at Data Robotics, Inc.™ have been working since 2004 to make

protecting, storing and managing your digital content truly effortless.

Why Drobo?

The Drobo family of products provides effortless, safe and expandable

storage. There are many different ways to store and protect digital

content, but Drobo is the only fully automatic storage device that

performs many data management tasks without user effort. Here’s

what you can expect:

Fully automated data protection and management

• Drobo automatically configures itself for data protection so you

don’t have to.

• When a drive fails, your data is still safe (and all drives do

eventually fail).

• Drobo senses any corrupted data and ensures that you only

access non-corrupt data.

• No downtime to add capacity. Just add a drive to an empty Data

Bay, or replace a smaller drive with a larger one regardless of

capacity, speed, or manufacturer.

• After a drive is installed into an empty bay, the new drive

capacity is immediately available and protected.

• Drobo can act as one large drive, making it easier to find what

you’ve stored on it.

• Drobo’s Data Bay indicator lights tell you everything you need to

know!

Infinite expansion

• Upgrading capacity is as simple as adding ink to a printer.

• Mix ’n match any 3.5” (SATA) hard drives; no worrying about

matching make, model or capacity of Drobo’s existing drives.

• Upgrade forever—just replace Drobo’s smallest drive with a

larger capacity drive. No data migration or reconfiguration is

required.

2

BeyondRAID™ storage technology

What does it mean to go BeyondRAID? Going beyond traditional RAID

means leaving choices between striping and mirroring, limitations on

expandability, drive sizing, and drive ordering behind. BeyondRAID™

technology is the next generation of storage that brings together safety,

reliability, expandability, efficiency and of course ease-of-use.

BeyondRAID can be adopted without any change in infrastructure,

allowing you to maintain your current file system and operating system–

eliminating the friction costs typically associated with moving to a new

technology platform.

Standard RAID levels are full of compromises. Do you want striping or

mirroring? A two-disk or four-disk RAID set? BeyondRAID is able to solve

these issues because it is built on an advanced virtualization platform. If

you already understand how RAID 0, 1, 5 or 6 operate(s), you

understand the fundamentals of BeyondRAID since BeyondRAID relies

on the same underlying algorithms.

Welcome to the world’s best storage experience.

Who is Data Robotics, Inc.?

Data Robotics, Inc. was formed in 2004 in California’s Silicon Valley with

a vision to take the pain out of storage management. Data Robotics, Inc.

developed the technology inside Drobo for people who “have to”

protect their valuable digital assets, but “hate to” – because it’s

complex and time consuming. For those people, we created Drobo, the

world’s first storage robot. It is a fully automated data storage system

that provides the only truly effortless, safe and expandable storage

solution. Unlike outdated technologies that emerged twenty plus years

ago and the frustrating products on the market today, Drobo is an

industry-changing product line that combines the advanced concepts of

storage virtualization and cybernetics, to take the pain out of storage

management.

3

II. Getting started

Your Drobo file sharing product (FS storage array) is designed to share

data over a network. This eliminates the problems of physically moving

your storage device between computers and having to take into account

different file system formats in order to share your data.

Three easy steps

To set up your FS array, you will need to do the following:

1. Install Drobo Dashboard – After installation, launch Drobo

Dashboard and leave it running while you complete the setup.

2. Insert drives – Use any 3.5” SATA drives. Start with at least two

drives to protect your valuable data. If you plan to use Dual Disk

Redundancy, start with at least three drives. All data on the

drives will be erased.

3. Connect cables – Connect the FS array to your network and

then connect power.

Drobo Dashboard will automatically discover your FS storage array. It

will take a few minutes for your device to finish its initial setup. After

the unit is ready, you should set the administrative username and

password. Then you can create new shares, add users, and change other

settings.

You will find more details on the setup in the “Drobo FS Setup” section

on page 7 or the “DroboPro FS Setup” on page 11.

Selecting hard drives

Drobo devices are unlike typical storage devices. They make it extremely

easy to increase storage capacity in the future by simply inserting

additional drives or replacing smaller drives with larger ones. This

means you can buy the storage you need today and then easily expand

later. You can save hundreds of dollars over time.

Drobo storage devices don’t care what manufacturer, capacity or speed

of hard drive you install. They accept all standard 3.5-inch internal SATA

hard drives. SSD, SCSI and older IDE or ATA-type drives will not work.

Warning! Please note that when adding hard drives to your Drobo storage

device, any pre-existing data on those drives will be erased.

4

Choosing capacity

The number and capacity of drives determine how much usable

protected storage your FS array provides. Take the guesswork out by

using our Capacity Calculator at

www.drobo.com/calculator, a web-

based tool which determines the actual usable protected capacity,

based on any combination of drives. To calculate the approximate

capacity yourself, omit the largest drive and then add-up the capacity of

the remaining drives. If you plan to use dual disk redundancy, omit the

largest two drives. For example (largest drives are crossed out):

Single Disk (Default) Redundancy

# Drives Drive Capacities Usable Protected Capacity*

3 250GB + 250GB + 250GB = 500GB

4 250GB + 250GB + 250GB + 500GB = 750GB

4 750GB + 250GB + 250GB + 500GB = 1000GB

Dual Disk Redundancy

# Drives

Drive Capacities

Usable Protected Capacity*

4 250GB + 250GB + 250GB + 500GB = 500GB

5

750GB + 500GB + 500GB + 500GB + 250GB

=

1250GB

5 750GB + 1000GB + 500GB + 500GB + 500GB = 1500GB

* Actual capacity will typically be less than these numbers due to different

systems used for rating capacity. These discrepancies have nothing to do with

Drobo storage devices.

Keeping your product up-to-date

During your initial setup, Drobo Dashboard asks if you want to check for

updates automatically. We highly recommend you select the “Yes”

option to assure optimal performance of your FS array. This feature

enables you to keep both Drobo Dashboard and your product’s

firmware current. Subsequently, you will receive a notice when a newer

version is available. You can check for the most current versions at

www.drobo.com/support/updates.

Safe Shutdown of your FS array

In the event that you need to shut your FS array down for any reason, it

is very important that you shut it down in a safe manner in order to

protect your valuable data. Improper shutdown can result in lost data.

5

It is always advisable to shut your FS array before disconnecting the

Ethernet cable(s) or power cord. In most cases, you can do the

following:

1. Check the activity light on your FS array to make sure no user or

application is accessing the FS array. (The activity light should be

off.)

2. In Drobo Dashboard, go to Advanced Settings -> Tools.

3. Click the “Shutdown” button.

4. After the power light has turned off, it is safe to disconnect

power, Ethernet cable(s) and remove the disk pack as required.

For more detail, including different situations or lack of access to Drobo

Dashboard, please see our knowledgebase article,

How do I safely shut

down my Drobo FS, DroboPro FS, Drobo S, DroboPro or DroboElite?

Saving Power

If you are concerned about saving power, you don’t need to worry

about turning off your FS array when not using it. The device

automatically goes into a power saving mode (spins down the hard

drives) when it has not been accessed for 15 minutes (default) or the

time you selected in the General tab. Note that when the drives have

spun down, it will take your FS array a few moments to spin the drives

back up again when you try to access it.

Note: Both Drobo FS and DroboPro FS allow you to modify the time intervals for

disk drive spin down. See page 21 for details.

What to do when not using your FS storage array

If you are not going to be using your FS array for an extended period of

time, then it is a good idea to shut it down. Make sure that no

applications on your computer are using the device by checking the

activity light. If applications are using your FS array, they may prevent it

from properly disconnecting.

Open Drobo Dashboard and click Advanced Controls -> Tools. Then click

the “Shutdown” button. Make sure the power light is off before

disconnecting the data cable or power cord.

6

If you do not have access to Drobo Dashboard for any reason, then:

1. Check the activity indicator to assure there is no data being

transferred to or from your FS array.

2. Toggle the power switch on the back of your FS array.

3. When the power indicator goes off, it is safe to remove the

power cord and data cable(s) from the back of the unit.

Best Practices

There are a number of things you can do to protect your valuable data.

Using a Drobo storage product is obviously a major step. However,

there are additional actions you can take to provide even greater safety

for your data. To learn more about this important topic, please visit our

Best Practices site at

www.drobo.com/support/best_practices.

Online Resources and Assistance

Data Robotics, Inc. provides an extensive online knowledgebase to help

you resolve issues, check for product updates, access electronic

documentation, request technical support, etc. Please visit this valuable

resource at:

http://support.datarobotics.com/.

7

III. Drobo FS Setup

Install Drobo Dashboard

If you have not already installed Drobo Dashboard, insert the Drobo

Resource CD that came with your Drobo FS into your computer. (Make

sure it is connected to your network.) You can also download the latest

version of Drobo Dashboard at:

www.drobo.com/support/updates.

From the on-screen menu, select “Install.” After Drobo Dashboard is

installed, it will start automatically. Drobo Dashboard assigns “Drobo-

FS” as the default name for your Drobo FS and automatically formats

the volume when it first discovers your Drobo FS. To change the name

of your Drobo FS, see page 21.

Note: To install Drobo Dashboard, you will need to have administrative rights

on your computer.

Inserting drives into Drobo FS

Once you’ve chosen the number and capacities of drives to install, all

you have to do is remove the face plate of your Drobo FS by simply

pulling it off and then sliding the drives into the Data Bays. It doesn’t

matter which drive goes into which Data Bay. You should note that any

pre-existing data on the drives will be erased. Be sure not to touch any

exposed hard drive circuit boards after unpacking.

First orient the drive connectors so that they are pointed towards the

Drobo FS and are at the bottom of the drive (as shown). Open the Drive

Lock by pressing it towards the left and slide the drive into the Data Bay

until you feel the connector “mate” at the rear of the Drobo FS. If the

connectors seat properly, the Drive Lock will snap behind the drive,

securing it into place.

8

Tip: Insert the drive with top silver plate facing up (circuit board down).

Connect Drobo FS to your network

Ethernet

Your Drobo FS connects to a network using an Ethernet port. Use the

Ethernet connection on the back of the Drobo FS to connect to a router

or switch. Use the Ethernet cable included with the original Drobo FS.

Note: Drobo FS supports a gigabit (1000 Mbit/s) connection. It will auto-

negotiate the highest connection speed available to the router or switch. You

will not get optimal performance if you are using a slower connection (10/100

Mbit/s).

Connect power

Once you have connected Drobo FS to your network, the next step is to

connect it to an AC power source. Simply connect the power cord to the

back of the Drobo FS and to your power source. Then press the toggle

power button on the back of the unit to turn your Drobo FS on.

9

Note: As with all electronic equipment, we recommend connecting your

Drobo FS to a surge protector or uninterruptible power supply (UPS), designed

for electronics.

Initialize your Drobo FS

Your Drobo FS is set to automatically obtain an IP address (DHCP) on

your network. When you connect Drobo FS to the network, Drobo

Dashboard will automatically discover it. After Drobo Dashboard

discovers your Drobo FS, you can set a static IP address if desired. If you

don’t have DCHP and need to use a static IP address, you should directly

connect the Drobo FS to your computer’s Ethernet connection for the

initial setup. See the section, “Tips and Troubleshooting” on page 34 for

further information on direct-connect and setting the IP address of your

Drobo FS.

After you do the initial setup of your Drobo FS, you should set the

administrative username and password. You are required to do this

before you can set up shares, users, etc. Drobo Dashboard will prompt

you for share names, usernames, etc. Please see page 24 for further

information on managing shares.

10

Drobo FS Lights

One of the many benefits of your Drobo FS is a series of lights that tell

you everything you need to know, without your having to launch any

application software on your computer. Remember, Drobo FS is

designed to actively monitor and protect your data at all times.

Drobo FS will automatically take any necessary actions and display them

using the following lights:

Drive Lights

Green: No action is required. All drives are healthy.

Solid Yellow: Add a drive or replace the current drive with a

larger drive soon. Drobo FS is running out of disk space.

Blinking Yellow and Green: Do not remove these drives or

power down. Drobo FS is working to protect your data.

Solid Red: Add a drive or replace the current drive with a

larger drive immediately. Drobo FS is critically low on space.

Blinking Red: Replace this drive immediately. This drive has

failed and needs to be replaced.

Power Light

Green: The power is on and Drobo FS is ready.

Yellow: Drobo FS is in standby mode.

Red: Drobo FS has overheated. Disconnect the data cable

and then the power cable. Let it cool down for at least 30

minutes and then restart.

Activity Light

Blinking Green: Data is actively being transferred between

your computer and Drobo FS.

Capacity Gauge

Blue: Displays the percentage of your Drobo FS that is full, in

10% increments.

Note: You can find information about the lights on the inside of the face plate.

11

IV. DroboPro FS Setup

Install Drobo Dashboard

If you have not already installed Drobo Dashboard, insert the Drobo

Resource CD that came with your DroboPro FS into your computer.

(Make sure it is connected to your network.) You can also download the

latest version of Drobo Dashboard at:

www.drobo.com/support/updates. (DroboPro FS requires version 1.8.0

or higher.) From the on-screen menu, select “Install.” After Drobo

Dashboard is installed, it will start automatically. Drobo Dashboard

assigns “DroboPro-FS” as the default name for your DroboPro FS device

and automatically formats Volume 1 and Volume 2 (16 TB each) when it

first discovers your DroboPro FS. To change the name of your

DroboPro FS, see page 21.

Note: To install Drobo Dashboard, you will need to have administrative rights

on your computer.

Inserting drives into your DroboPro FS

Once you’ve chosen the number and capacities of drives to install, all

you have to do is remove the face plate of your DroboPro FS by simply

pulling it off and then sliding the drives into the Data Bays. It doesn’t

matter which drive goes into which Data Bay. You should note that any

pre-existing data on the drives will be erased. Be sure not to touch any

exposed hard drive circuit boards after unpacking.

First orient the drive

connectors so that the

connectors are pointed

towards the DroboPro FS and

they are facing the left side of the

device. The top silver colored plate of

the drive should be facing to the right. Open the Drive Lock by pressing

it down and slide the drive into the Data Bay until you feel the

connector “mate” at the rear of the unit. If the connectors seat

properly, the Drive Lock will snap behind the drive, securing it into

place.

Warning! Do not place your DroboPro FS on its side during normal operation.

There is a chance the drives will disconnect if you do this. For optimal

performance and protection of your data we recommend that the DroboPro FS

remain in its normal horizontal position.

La page est en cours de chargement...

DATA ROBOTICS DROBOPRO FS Le manuel du propriétaire

Ce manuel convient également à

DATA ROBOTICS DROBOPRO FS Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents