KitchenAid KDSS907SSS05 Guide d'installation

Marque: KitchenAid

Modèle: KDSS907SSS05

Taper: Guide d'installation

Ce manuel convient également à

KDRS807SSS05

Kitchen_kid _

INSTALLATION INSTRI3CTIONS

30" (76.2 CM) FREESTANDING AND SLIDE-IN

DUAL FUEL RANGES

INSTRUCTIONS D'INSTALLATION DES

CUISINIERES AUTOPORTANTES ET

ENCASTRABLES A BI-COMBUSTIBLE

DE 30"(76,2 CM)

Table of Contents/Table des matieres .................................................................................. 2

iMPORTANT:

Save for local electrical inspector's use.

Installer: Leave installation instructions with the homeowner.

Homeowner: Keep installation instructions for future reference.

iMPORTANT :

_, conserver pour consultation par I'inspecteur local des installations 61ectriques.

Installateur : Remettre les instructions d'installation au propri6taire.

Propri6taire : Conserver les instructions d'installation pour r6f&ence ult&ieure.

W10440543A

TABLEOF CONTENTS

RAN GE SAFETY ............................................................................. 2

INSTALLATION REQUIREMENTS ................................................ 4

Tools and Parts ............................................................................ 4

Location Requirements ................................................................ 4

Electrical Requirements - U.S.A. Only ......................................... 7

Electrical Requirements - Canada Only ....................................... 8

Gas Supply Requirements ........................................................... 8

Countertop Preparation ............................................................... 9

INSTALLATION INSTRUCTIONS ................................................ 10

Unpack Range ............................................................................ 10

Measure for Proper Height......................................................... 10

Adjust Leveling Legs.................................................................. 11

Install Anti-Tip Bracket ............................................................... 11

Remove Warming Drawer .......................................................... 12

Electrical Connection - U.S.A. Only ........................................... 12

Make Gas Connection ............................................................... 17

Electronic IgnitionSystem ......................................................... 18

Verify Anti-Tip Bracket Is Installed and Engaged ...................... 19

Level Range................................................................................ 19

Replace Oven Racks and Warming Drawer .............................. 19

Complete Installation ................................................................. 20

GAS CONVERSIONS .................................................................... 20

LP Gas Conversion .................................................................... 20

Natural Gas Conversion ............................................................. 22

TABLEDES MATIERES

SECURITE DE LA CUISINIERE ................................................... 25

EXIGENCES D'INSTALLATION ................................................... 27

Outillage et pieces ...................................................................... 27

Exigences d'emplacement ......................................................... 27

Specifications electriques .......................................................... 30

Specifications de I'alimentation en gaz ..................................... 30

Preparation du plan de travail.................................................... 32

INSTRUCTIONS D'INSTALLATION ............................................. 32

Deballage de la cuisiniere .......................................................... 32

Mesures pour une hauteur appropriee ...................................... 32

Reglage des pieds de nivellement ............................................. 33

Installation de la bride antibasculement .................................... 33

Retrait du tiroir-rechaud ............................................................. 34

Raccordement a la canalisation de gaz ..................................... 35

Systeme d'allumage electronique .............................................. 36

Verifier que la bride anti-basculement est

bien installee et engagee ............................................................ 37

Reglage de I'aplomb de la cuisiniere ......................................... 37

Reinstallation des grilles du four et du tiroir-rechaud ................ 38

Achever I'installation .................................................................. 38

CONVERSIONS POUR CHANGEMENT DE GAZ....................... 39

Conversion pour I'alimentation au propane ............................... 39

Conversion pour I'alimentation au gaz naturel .......................... 41

RANGE SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

WARNING: If the information in this manual is not followed exactly, a fire or explosion

may result causing property damage, personal injury or death.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or

the gas supplier,

WARNING: Gas leaks cannot always be detected by smell.

Gas suppliers recommend that you use a gas detector approved by UL or CSA.

For more information, contact your gas supplier.

If a gas leak is detected, follow the "What to do if you smell gas" instructions.

In the State of Massachusetts, the following installation instructions apply:

[] Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

[] If using a ball valve, it shall be a T-handle type.

[] A flexible gas connector, when used, must not exceed 3 feet.

Anti-Tip

Bracket

Range Foot

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation instructions.

Slide range back so rear range foot is engaged in the slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed and engaged.

Failure to follow these instructions can result in death or serious burns to children and adults.

To verify the anti-tip bracket is installed and engaged:

• Slide range forward.

• Look for the anti-tip bracket securely attached to floor or wall.

• Slide range back so rear range foot is under anti-tip bracket.

• See installation instructions for details.

INSTALLATION REQUIREMENTS

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

• Tape measure • Masking tape

• Flat-blade screwdriver • Pipe-joint compound

resistant to LP gas

• Phillips screwdriver

• Level • 3/16"(4.8 mm) carbide-tipped

masonry drill bit (for

• Hand or electric drill concrete/ceramic floors)

• Hammer • Noncorrosive leak-detection

solution

• Wrench or pliers

For LP/Natural Gas

• Pipe wrench

Conversions

• 1%e"combination wrench • 1/2"combination wrench

• 3/8"nut driver • 7 mm combination wrench

• 1/4"nut driver • 7 mm nut driver

• 1/8"(3.2 mm) drill bit (for • Size T20®TORX ®t

wood floors) screwdriver

• Marker or pencil

Parts supplied

Check that all parts are included.

A. Anti-tip bracket

B. #12 x 1%" screws

Anti-tip bracket must be securely mounted to subfloor or

wall. Thickness of flooring may require longer mounting

screws to anchor bracket to subfloor. Longer mounting

screws are available from your local hardware store.

Parts needed

Check local codes and consult gas supplier. Check existing gas

supply and electrical supply. See "Electrical Requirements" and

"Gas Supply Requirements" sections.

Rear Filler Strip (optional)

The filler strip may be used to fill a gap between the rear of the

slide-in range and the wall in a freestanding range cutout.

A. Filler strip

B. Countertop

C. Countertop cutout

To order, see the "Assistance or Service" section of the Use and

Care Guide. Order Part Number W10113902A (black),

W10113903A (white) or W10113904A (biscuit).

IMPORTANT: Observe all governing codes and ordinances. Do

not obstruct flow of combustion and ventilation air.

• It is the installer's responsibility to comply with installation

clearances specified on the model/serial rating plate. The

model/serial rating plate is located inside the oven door on

the right-hand side oven door trim.

• The range should be located for convenient use in the

kitchen.

• Recessed installations must provide complete enclosure of

the sides and rear of the range.

• To eliminate the risk of burns or fire by reaching over heated

surface units, cabinet storage space located above the

surface units should be avoided. If cabinet storage is to be

provided, the risk can be reduced by installing a range hood

or microwave hood combination that projects horizontally a

minimum of 5" (12.7 cm) beyond the bottom of the cabinets.

• All openings in the wall or floor where range is to be installed

must be sealed.

• Do not seal the range to the side cabinets.

• Cabinet opening dimensions that are shown must be used.

Given dimensions are minimum clearances.

1-®TORX and T20 are registered trademarks of Saturn Fasteners, Inc.

• The anti-tip bracket must be installed. To install the anti-tip

bracket shipped with the range, see "Install Anti-Tip Bracket"

section.

• Grounded electrical supply is required. See "Electrical

Requirements" section.

• Proper gas supply connection must be available. See "Gas

Supply Requirements" section.

• Contact a qualified floor covering installer to check that the

floor covering can withstand at least 200°F (93°C).

• Use an insulated pad or 1¼,(0.64 cm) plywood under range if

installing range over carpeting.

IMPORTANT: To avoid damage to your cabinets, check with your

builder or cabinet supplier to make sure that the materials used

will not discolor, delaminate or sustain other damage. This oven

has been designed in accordance with the requirements of UL

and CSA International and complies with the maximum allowable

wood cabinet temperatures of 194°F (90°C).

Mobile Home - Additional Installation Requirements

The installation of this range must conform to the Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280

(formerly the Federal Standard for Mobile Home Construction

and Safety, Title 24, HUD Part 280). When such standard is not

applicable, use the Standard for Manufactured Home

Installations, ANSI A225.1/NFPA 501A or with local codes.

In Canada, the installation of this range must conform with the

current standards CAN/CSA-A240-1atest edition, or with local

codes.

Mobile home installations require:

• When this range is installed in a mobile home, it must be

secured to the floor during transit. Any method of securing

the range is adequate as long as it conforms to the standards

listed above.

• Four-wire power supply cord or cable must be used in a

mobile home installation. The appliance wiring will need to be

revised. See "Electrical Connection" section.

Product Dimensions

Freestanding Range Slide-in Range

A. 53/4'' (14.6 cm)

B. 30" (76.2 cm)

C. 413/4''(106.0 cm) overall height

with leveling legs screwed all

the way in. *

D. 36" (91.4 cm) cooktop trim

height with leveling legs

screwed all the way in*

E. Model/serial number plate

(located on the right-hand

side oven door trim)

F. 27¼" (69.2 cm) max. from

handle to standoff at back

of range**

*Range can be raised approximately 1" (2.5 cm) by adjusting

the leveling legs.

**When installed in a 24" (61.0 cm) base cabinet with 25"

(63.5 cm) countertop; front of oven door protrudes 1" (2.5 cm)

beyond 24" (61.0 cm) base cabinet.

A. 309/16''(77.6 cm)

B. 35%" (90.5 cm) height to

underside of cooktop edge

with leveling legs screwed

all the way in*

C. Model/serial number plate

(located on the right-hand

side oven door trim)

D 30" (76.2 cm)

E. 27¼" (69.2 cm)

(271¼_,,[70.3 cm] on

models KDRS807XSP

and KDSS907XSP) from

handle to standoff at

back of range**

F. 23" (58.4 cm) countertop

notch to rear of cooktop

*Range can be raised approximately 1" (2.5 cm) by adjusting

the leveling legs.

**When installed in a 24" (61 cm) base cabinet with 25" (63.5 cm)

countertop; front of oven door protrudes 13/4'' (4.4 cm)

(23/le'' [5.5 cm] on models KDRS807XSP and KDSS907XSP)

beyond 24" (61.0 cm) base cabinet.

Installation Clearances

Cabinet opening dimensions shown are for 25" (64.0 cm) countertop depth, 24" (61.0 cm) base cabinet depth and 36" (91.4 cm)

countertop height.

IMPORTANT: If installing a range hood or microwave hood combination above the range, follow the range hood or microwave hood

combination installation instructions for dimensional clearances above the cooktop surface.

Freestanding Ranges

A. 18" (45. 7 cm) upper cabinet to countertop

B. 13" (33.0 cm) upper cabinet depth

C. 30" (76.2 cm) min. opening width

D. For minimum clearance to top of the cooktop, see NOTE.

E.30" (76.2 cm) min. opening width

E This shaded area recommended for installation of rigid gas pipe.

G. 8" (20.3 cm) available area for gas and electric installation

H. This shaded area recommended for installation of outlet or

junction box.

/. 7" (17.8 cm)

J. 11/2''(3.8 cm)

K. 41/2"(11.4 cm)

L. 5" (12.7 cm) min. clearance from both sides of the range to the

side wall or other combustible material.

M. Cabinet door or hinge should not extend into the cutout.

Slide-In Ranges

A. 18" (45.7 cm) upper cabinet to countertop

B. 13" (33.0 cm) max. upper cabinet depth

C. 30" (76.2 cm) min. opening width

D. For minimum clearance to top of the cooktop, see NOTE.

E. 30" (76.2 cm) min. opening width

E This shaded area recommended for installation of rigid gas pipe.

G. 6" (15.2 cm) available area for gas and electric installation

H. This shaded area recommended for installation of outlet or

junction box.

/. 7" (17.8 cm)

J. 11/2'' (3.8 cm)

K. 41/2"(11.4 cm)

L. 5" (12.7 cm) min. clearance from both sides of the range to the

side wall or other combustible material.

M. 22 15A_"(58.3 cm) opening depth

N. 3/4"(1.9 cm) radius both corners

O. Cabinet door or hinge should not extend into the cutout.

NOTE: 24" (61.0 cm) minimum when bottom of wood or metal cabinet is covered by not less than 1/4"(0.64 cm) flame retardant

millboard covered with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or

0.020" (0.5 mm) copper.

30" (76.2 cm) minimum clearance between the top of the cooking platform and the bottom of an uncovered wood or metal cabinet.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrical installer determine that

the ground path is adequate and wire gauge is in accordance

with local codes.

Do not use an extension cord.

Be sure that the electrical connection and wire size are adequate

and in conformance with the National Electrical Code, ANSI/

NFPA 70-latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

WARNING: Improper connection of the equipment-grounding

conductor can result in a risk of electric shock. Check with a

qualified electrician or service technician if you are in doubt as to

whether the appliance is properly grounded. Do not modify the

power supply cord plug. If it will not fit the outlet, have a proper

outlet installed by a qualified electrician.

If connecting to a 4-wire system:

This range is manufactured with the ground connected to the

cabinet. The ground must be revised so the green ground wire of

the 4-wire power supply cord is connected to the cabinet. See

the "Electrical Connection" section.

Grounding through the neutral conductor is prohibited for new

branch-circuit installations (1996 NEC); mobile homes; and

recreational vehicles, or an area where local codes prohibit

grounding through the neutral conductor.

When a 4-wire receptacle of NEMA Type 14-50R is used, a

matching UL listed, 4-wire, 250-volt, 40-amp, range power

supply cord (pigtail) must be used. This cord contains 4 copper

conductors with ring terminals or open-end spade terminals with

upturned ends, terminating in a NEMA Type 14-50P plug on the

supply end.

The fourth (grounding) conductor must be identified by a green or

green/yellow cover and the neutral conductor by a white cover.

Cord should be Type SRD or SRDT with a UL listed strain relief

and be at least 4 ft (1.22 m) long.

Electrical Connection

To properly install your range, you must determine the type of

electrical connection you will be using and follow the instructions

provided for it here.

• Range must be connected to the proper electrical voltage

and frequency as specified on the model/serial number rating

plate. The model/serial rating plate is located inside the oven

door on the right-hand side oven door trim. Refer to the

figures in the "Product Dimensions" section of the "Location

Requirements" section.

• This range is manufactured with the neutral terminal

connected to the cabinet. Use a 3-wire UL listed, 40- or

50-amp power supply cord (pigtail) (see following Range

Rating chart). If local codes do not permit ground through the

neutral, use a 4-wire power supply cord rated at 250 volts,

40 or 50 amps and investigated for use with ranges.

Range Rating* Specified Rating of

Power Supply Cord Kit

and Circuit Protection

120/240 Volts 120/208 Volts Amps

8.8 - 16.5 KW 7.8 - 12.5 KW 40 or 50**

16.6 - 22.5 KW 12.6 - 18.5 KW 50

4-wire receptacle (14-50R)

The minimum conductor sized for the copper 4-wire power

cord are:

40-amp circuit

2 No.-8 conductors

1 No.-10 white neutral

1 No.-8 green grounding

If connecting to a 3-wire system:

Local codes may permit the use of a UL listed, 3-wire,

250 volt, 40-amp range power supply cord (pigtail). This cord

contains 3 copper conductors with ring terminals or open-end

spade terminals with upturned ends, terminating in a NEMA Type

10-50P plug on the supply end. Connectors on the appliance end

must be provided at the point the power supply cord enters the

appliance. This uses a 3-wire receptacle of NEMA Type 10-50R.

*The NEC calculated load is less than the total connected load

listed on the model/serial rating plate.

**If connecting to a 50-amp circuit, use a50-amp rated cord with

kit. For 50-amp rated cord kits, use kits that specify use with a

nominal 13/8"(34.93 mm) diameter connection opening.

• A circuit breaker is recommended.

The range can be connected directly to the fused disconnect

(or circuit breaker box) through flexible or nonmetallic

sheathed, copper or aluminum cable. See the "Electrical

Connection" section.

• Allow 2 to 3 ft (61.0 cm to 91.4 cm) of slack in the line so that

the range can be moved if servicing is ever necessary.

• A UL listed conduit connector must be provided at each end

of the power supply cable (at the range and at the junction

box).

• Wire sizes and connections must conform with the rating of

the range (40 amps).

• The wiring diagram is located on the underside of the storage

drawer or below the warming drawer in a clear plastic bag.

3-wire receptacle (10-50R)

liii! tec/ si-icat Ii Leq i s<s.ests- .....ty

Electrical Shock Hazard

Electrically ground range.

Failure to do so can result in death, fire, or

electrical shock.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrical installer determine that

the ground path is adequate and wire gauge are in accordance

with local codes.

Be sure that the electrical connection and wire size are adequate

and in conformance with CSA Standard C22.1, Canadian

Electrical Code, Part 1 - latest edition, and all local codes and

ordinances.

A copy of the above code standards can be obtained from:

Canadian Standards Association

178 Rexdale Blvd.

Toronto, ON M9W 1R3 CANADA

Check with a qualified electrical installer if you are not sure

the range is properly grounded.

Range Rating* Specified Rating of

Power Supply Cord Kit

and Circuit Protection

120/240 Volts 120/208 Volts Amps

8.8 - 16.5 KW 7.8 - 12.5 KW 40 or 50

16.6 - 22.5 KW 12.6 - 18.5 KW 50

*The NEC calculated load is less than the total connected load

listed on the model/serial/rating plate.

**If connecting to a 50-amp circuit, use a50-amp rated cord with

kit. For 50-amp rated cord kits, use kits that specify use with a

nominal 13/8"(34.9 mm) diameter connection opening.

• A time-delay fuse or circuit breaker is recommended.

• This range is equipped with a CSA International Certified

Power Cord intended to be plugged into a standard 14-50R

wall receptacle. Be sure the wall receptacle is within reach of

range's final location.

• Do not use an extension cord.

(as Req _,,-'_?:xs.est!__

Explosion Hazard

Use a new CSA international approved gas supply line.

install a shut=off valve.

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 14" (36 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Observe all governing codes and ordinances.

IMPORTANT: This installation must conform with all local codes

and ordinances. In the absence of local codes, installation must

conform with American National Standard, National Fuel Gas

Code ANSI Z223.1 -latest edition or CAN/CGA B149 -latest

edition.

IMPORTANT: Leak testing of the range must be conducted

according to the manufacturer's instructions.

Type of Gas

Natural gas:

This range is design-certified by CSA International for use with

Natural gas or, after proper conversion, for use with LP gas.

• This range is factory set for use with Natural gas. See "Gas

Conversions" section. The model/serial rating plate located

behind the storage drawer on the right-hand side oven door

frame has information on the types of gas that can be used. If

the types of gas listed do not include the type of gas

available, check with the local gas supplier.

LP gas conversion:

Conversion must be done by a qualified service technician.

No attempt shall be made to convert the appliance from the gas

specified on the model/serial rating plate for use with a different

gas without consulting the serving gas supplier. See "Gas

Conversions" section.

Gas Supply Line

• Provide a gas supply line of 3_,,(1.9 cm) rigid pipe to the

range location. A smaller size pipe on longer runs may result

in insufficient gas supply. With LP gas, piping or tubing size

can be 1/2"(1.3 cm) minimum. Usually, LP gas suppliers

determine the size and materials used in the system.

NOTE: Pipe-joint compounds that resist the action of LP gas

must be used. Do not use TEFLON ®t tape.

1-®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

Flexible metal appliance connector:

If local codes permit, a new CSA design-certified,

4 to 5 ft (122 to 152.4 cm) long, 1/2"(1.3 cm) or

3_,,(1.9 cm) I.D., flexible metal appliance connector may

be used for connecting range to the gas supply line.

• A 1/2"(1.3 cm) male pipe thread is needed for connection

to the female pipe threads of the inlet to the appliance

pressure regulator.

• Do not kink or damage the flexible metal tubing when

moving the range.

Rigid pipe connection:

The rigid pipe connection requires a combination of pipe

fittings to obtain an in-line connection to the range. The rigid

pipe must be level with the range connection. All strains must

be removed from the supply and fuel lines so range will be

level and in line.

Must include a shutoff valve:

The supply line must be equipped with a manual shutoff

valve. This valve should be located in the same room but

external to the range opening, such as an adjacent cabinet. It

should be in a location that allows ease of opening and

closing. Do not block access to shutoff valve. The valve is for

turning on or shutting off gas to the range.

A. Gas supply line

B. Shutoff valve "open" position

C. To range

Gas Pressure Regulator

The gas pressure regulator supplied with this range must be

used. The inlet pressure to the regulator should be as follows for

proper operation:

Natural gas:

Minimum pressure: 5" WCP

Maximum pressure: 14" WCP

LP gas:

Minimum pressure: 11" WCP

Maximum pressure: 14" WCP

Contact local gas supplier if you are not sure about the inlet

pressure.

Burner Input Requirements

Input ratings shown on the model/serial rating plate are for

elevations up to 2,000 ft (609.6 m).

For elevations above 2,000 ft (609.6 m), ratings are reduced at a

rate of 4% for each 1,000 ft (304.8 m) above sea level (not

applicable for Canada).

Gas Supply Pressure Testing

Gas supply pressure for testing regulator must be at least

1" water column pressure above the manifold pressure shown on

the model/serial rating plate.

Line pressure testing above 1/2psi gauge (14" WCP)

The range and its individual shutoff valve must be disconnected

from the gas supply piping system during any pressure testing of

that system at test pressures in excess of 1/2psi (3.5 kPa).

Line pressure testing at 1/2psi gauge (14" WCP) or lower

The range must be isolated from the gas supply piping system by

closing its individual manual shutoff valve during any pressure

testing of the gas supply piping system at test pressures equal to

or less than 1/2psi (3.5 kPa).

The cooktop sides of the slide-in range fit over the cutout edge of

your countertop.

If you have a square finish (flat) countertop and the opening width

is 30" (76.2 cm), no countertop preparation is required.

Formed front-edged countertops must have molded edge

shaved flat 3/8"(1.0 cm) from each front corner of opening.

Tile countertops may need trim cut back 3/8"(1.0 cm) from each

front corner and/or rounded edge flattened.

(78.1 crn)

If countertop opening width is greater than 30" (76.2 cm), adjust

the 3/8"(1.0 cm) dimension.

Countertop must be level. Place level on countertop, first side to

side, then front to back. If countertop is not level, range will not

be level. Range must be level for satisfactory baking conditions.

INSTALLATION INSTRUCTIONS

2. Measure from the floor to the underside of the range cooktop.

Excessive Weight Hazard

Use two or more people to move and install range.

Failure to do so can result in back or other injury.

Remove shipping materials, tape and film from the range.

Keep cardboard bottom under range. Remove oven racks

and parts package from inside oven.

To place range on its back, take 4 cardboard corners from the

carton. Stack one cardboard corner on top of another.

Repeat with the other 2 corners. Place them lengthwise on

the floor behind the range to support the range when it is laid

on its back. Using 2 or more people, firmly grasp the range

and gently lay it on its back on the cardboard corners.

Slide-In Ranges:

1. Measure the distance of the countertop to the floor. Measure

at all 4 locations corresponding to the 4 corners of the

underside of the range cooktop, as shown.

A. Distance from the floor to

underside of range cooktop

B. Grate

C. Cooktop surface

D. Range side frame

3. Your leveling height will be the difference between the

2 measurements you have just taken.

Freestanding Ranges:

1. Measure the distance of the countertop to the floor.

2. Measure from the top of the range cooktop trim to the floor.

A. Distance from the top of the range

cooktop trim to the floor

Your leveling height will be the difference between the

2 measurements you have just taken.

Measure at locations marked A, B, C, D.

If range height adjustment is necessary, use a wrench or

pliers to loosen the 4 leveling legs.

This may be done with the range on its back or with the range

supported on 2 legs after the range has been placed back to

a standing position.

NOTE: To place range back up into astanding position, put a

sheet of cardboard or hardboard in front of range. Using 2 or

more people, stand range back up onto the cardboard or

hardboard.

2. Adjust the leveling legs to the correct height. Leveling legs

can be loosened to add up to a maximum of 1" (2.5 cm). A

minimum of 3/le"(5.0 mm) is needed to engage the anti-tip

bracket.

NOTE: If height adjustment is made when range is standing,

tilt the range back to adjust the front legs, then tilt forward to

adjust the rear legs.

3. When the range is at the correct height, check that there is

adequate clearance under the range for the anti-tip bracket.

Before sliding range into its final location, check that the anti-

tip bracket will slide under the range and onto the rear

leveling leg prior to anti-tip bracket installation.

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation

instructions.

Slide range back so rear range foot is engaged in the

slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed

and engaged.

Failure to follow these instructions can result in death

or serious burns to children and adults.

Remove the anti-tip bracket from where it is taped inside the

storage drawer or warming drawer.

Determine which mounting method to use: floor or wall.

If you have a stone or masonry floor, you can use the wall

mounting method. If you are installing the range in a mobile

home, you must secure the range to the floor.

Determine and mark the centerline of the cutout space. The

mounting can be installed on either the left side or right side

of the cutout. Position the mounting bracket against the wall

in the cutout so that the V-notch in the bracket is

1313/64"(33.6 cm) from the centerline as shown.

A. 1313/_,,(33.6 cm)

B. Bracket V-notch

4. Drill two V8"(3 mm) holes that correspond to the bracket

holes of the determined mounting method. See the following

illustrations.

Floor Mounting

Rearposition

Wall Mounting

Front position Diagonal (2 options)

Using a Phillips screwdriver, mount the anti-tip bracket to the

wall or floor with two #12 x 1%" screws provided.

Move the range close enough to the opening to allow for final

gas and electrical connections. Remove the shipping base,

cardboard or hardboard from under the range.

Move the range into its final location, making sure the rear

leveling leg slides into the anti-tip bracket.

Move the range forward onto shipping base, cardboard or

hardboard to continue installing the range using the following

installation instructions.

Remove the warming or storage drawer to gain access to the 3. Pull both loops forward at the same time, then pull drawer out

lower section of the range. This will be necessary for some of the another inch.

following installation steps.

To Remove Warming Drawer:

1. Open drawer to its fully open position.

2. Locate the black loops on both sides of the drawer.

4. Holding the drawer by its sides, not its front, gently pull it all

the way out.

A. Loop

Power Supply Cord

Electrical Shock Hazard

Disconnect power before servicing.

Use a new 40 amp power supply cord.

Plug into a grounded outlet.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Direct Wire

Electrical Shock Hazard

Disconnect power before servicing.

Use 8 gauge copper or 6 gauge aluminum wire.

Electrically ground range.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Disconnect power.

Remove the terminal block cover screws located on the back

of the range. Pull cover down and toward you to remove

cover.

A.Hold-down screws

B.Terminalblock cover

Remove plastic tag holding three 10-32 hex nuts from the

middle post of the terminal block.

4. Add strain relief.

Style 1: Power supply cord strain relief

• Remove the knockout at the bottom of the terminal box

for the 40-amp supply cord.

• Assemble a UL listed strain relief in the opening.

Feed the flexible conduit behind the black horizontal

cross brace and through the strain relief, allowing enough

slack to easily attach the wiring to the terminal block.

A. UL fisted strain relief

Feed the power supply cord behind the black horizontal

cross brace and through the strain relief, allowing enough

slack to easily attach the wiring to the terminal block.

A. Black horizontal cross brace

B. Power supply cord

• Tighten strain relief screw against the power supply cord.

Style 2: Direct wire strain relief

• Remove the knockout as needed for the flexible conduit

connection.

• Assemble a UL listed conduit connector in the opening.

A. Removable retaining nut

B. UL fisted strain relief

A. Black horizontal cross brace

B. Flexible conduit

• Tighten strain relief screw against the flexible conduit.

5. Complete installation following instructions for your type of

electrical connection:

4-wire (recommended)

3-wire (if 4-wire is not available)

Electrical Connection Options

If your home has: And you will be Go to Section:

connecting to:

4-wire receptacle A UL listed,

(NEMA type 14-50R) 250-volt

minimum,

40-amp, range

power supply

cord

4-wire connection:

Power supply cord

4-wire direct A fused

disconnect or

circuit breakerbox

(12.7 crn)

4-wire connection:

Direct wire

3-wire receptacle A UL listed,

(NEMA type 10-50R) 250-volt

minimum,

40-amp, range

power supply

cord

3-wire connection:

Power supply cord

3-wire direct A fused 3-wire connection:

3/8. disconnect or Direct wire

(1.0cn_)_, circuit breaker

box

',_f 3........ "

(7.6 crn)

4-wire connection: Power Supply Cord

Use this method for:

• New branch-circuit installations (1996 NEC)

• Mobile homes

• Recreational vehicles

• In an area where local codes prohibit grounding through the

neutral.

1. Cut out and remove part of the metal ground strap (B).

5. Use 3/8"nut driver to connect the neutral (white) wire to the

center terminal block 3ost with one of the 10-32 hex nuts.

A. Metal ground strap

B. Discard

C. Ground-link screw

2. Use a Phillips screwdriver to remove the ground-link screw

from the back of the range. Save the ground-link screw and

the end of the ground link under the screw.

3. Feed the power supply cord through the strain relief on the

cord/conduit plate on bottom of range. Allow enough slack to

easily attach the wiring to the terminal block.

A ......................

i,_¸_ ,

A. Terminal block

B. Ground-link screw

C. UL fisted strain relief

D. Power supply cord wires

Use a Phillips screwdriver to connect the green ground wire

from the power supply cord to the range with the ground-link

screw and ground-link section. The ground wire must be

attached first.

A. 10-32 hex nut

B. Ground-link screw

C. Line 2 (red)

D. Green ground wire

E.Neutral (center) wire

F. Line 1 (black)

6. Connect line 2 (red) and line 1 (black) wires to the outer

terminal block posts with 10-32 hex nuts.

7. Securely tighten hex nuts.

NOTE: For power supply cord replacement, use only a power

cord rated at 250 volts minimum, 40 amps or 50 amps that is

marked for use with nominal 13/8'' (3.5 cm) diameter

connection opening, with ring terminals and marked for use

with ranges.

8. Tighten strain relief screws.

9. Replace terminal block access cover.

3-wire connection: Power Supply Cord

Use this method only if local codes permit connecting chassis

ground conductor to neutral wire of power supply cord.

1. Feed the power supply cord through the strain relief on the

cord/conduit plate on bottom of range. Allow enough slack to

easily attach the wiring to the terminal block.

A ...................

A. Terminal block

B. Ground-link screw

C. UL listed strain relief

D. Power supply cord wires - large opening

2. Use 3/8"nut driver to connect the neutral (white) wire to the 1. Cut out and remove part of the metal ground strap (B).

center terminal block post with one of the 10-32 hex nuts.

A. 10-32 hex nut

B. Line 2 (red)

C. Ground-link screw

D. Neutral (white) wire

E.Line 1 (black)

3. Connect line 2 (red) and line 1 (black) wires to the outer

terminal block posts with 10-32 hex nuts.

4. Securely tighten hex nuts.

NOTE: For power supply cord replacement, use only a power

cord rated at 250 volts minimum, 40 amps or 50 amps that is

marked for use with nominal 13/8"(3.5 cm) diameter

connection opening, with ring terminals and marked for use

with ranges.

5. Tighten strain relief screws.

6. Replace terminal block access cover.

Direct Wire Installation: Copper or Aluminum Wire

This range may be connected directly to the fuse disconnect or

circuit breaker box. Depending on your electrical supply, make

the required 3-wire or 4-wire connection.

1. Strip outer covering back 3" (7.6 cm) to expose wires. Strip

the insulation back 3/8"(1.0 cm) from the end of each wire.

3/8.

(1.0crn)_.

_ ........... 3" -

(7.6 cm)

Allow enough slack in the wire to easily attach the wiring

terminal block.

3. Complete electrical connection according to your type of

electrical supply (4-wire or 3-wire connection).

4-wire Connection: Direct Wire

Use this method for:

• New branch-circuit installations (1996 NEC)

• Mobile homes

• Recreational vehicles

• In an area where local codes prohibit grounding through the

neutral

A. Metal ground strap

B. Discard

C. Ground-link screw

Use a Phillips screwdriver to remove the ground-link screw

from the back of the range. Save the ground-link screw and

the end of the ground link under the screw.

Pull the wires through the strain relief on bottom of range.

Allow enough slack to easily attach wiring to the terminal

block.

A ........................................ .......... " g

_ ........................................... , C

A. Terminal block E.Line 2 (red) wire

B. Ground-link screw E Neutral (white) wire

C. Cord/conduit plate G.Line 1 (black) wire

D.Bare (green)ground wire

Attach terminal lugs to line 1(black), neutral (white), and line 2

(red) wires. Loosen (do not remove) the setscrew on the front

of the terminal lug and insert exposed wire end through

bottom of terminal lugs. Securely tighten setscrew to torque

as shown in the following Bare Wire Torque Specifications

chart.

! !

A. Terminal lug

B. Setscrew

C. Line 2 (red) wire

D. Neutral (white) wire

E.Line 1 (black) wire

Bare Wire Torque Specifications

Attaching terminal lugs to the terminal block - 20 Ibs-in. (2.3 N-m)

Wire Awg Torque

8 gauge copper 25 Ibs-in. (2.8 N-m)

6 gauge aluminum 35 Ibs-in. (4.0 N-m)

5. Use a hex or Phillips screwdriver to connect the bare (green)

ground wire to the range with the ground-link screw and

ground-link section. The ground wire must be attached first

and must not contact any other terminal.

6. Use 3/8"nut driver to connect the neutral (white) wire to the

center terminal block post with one of the 10-32 hex nuts.

A. 10-32 hex nut

B. Line 2 (red)

C. Bare (green) ground wire

D. Ground-link screw

E. Neutral (white) wire

F. Line 1 (black)

G. Terminal lug

7. Connect line 2 (red) and line 1 (black) wires to the outer

terminal block posts with 10-32 hex nuts.

8. Securely tighten hex nuts.

9. Replace terminal block access cover.

3-wire connection: Direct Wire

Use this method only if local codes permit connecting ground

conductor to neutral supply wire.

1. Pull the wires through the conduit on cord/conduit plate on

bottom of range. Allow enough slack to easily attach the

wiring to the terminal block.

.............ii

Attach terminal lugs to line 2 (red), bare (green) ground, and

line 1 (black) wires. Loosen (do not remove) the setscrew on

the front of the terminal lug and insert exposed wire end

through bottom of terminal lugs. Securely tighten setscrew to

torque as shown in the following Bare Wire Torque

Specifications chart.

C D

A. Terminal lug

B. Setscrew

C. Line 2 (red) wire

D. Bare (green) ground wire

E. Line 1 (black) wire

Bare Wire Torque Specifications

Attaching terminal lugs to the terminal block - 20 Ibs-in. (2.3 N-m)

Wire Awg Torque

8 gauge copper 25 Ibs-in. (2.8 N-m)

6 gauge aluminum 35 Ibs-in. (4.0 N-m)

3. Use 3/8"nut driver to connect the bare (green) ground wire to

the center terminal block post with one of the 10-32 hex nuts.

A. 10-32 hex nut

B. Line 2 (red)

C. Ground-link screw

D. Bare (green) ground wire

E.Line 1 (black)

F. Terminal lug

4. Connect line 2 (red) and line 1 (black) wires to the outer

terminal block posts with 10-32 hex nuts.

5. Securely tighten hex nuts.

6. Replace terminal block access cover.

A. Terminal block

B. Ground-link screw

C. Cord/conduit plate

D. Line 2 (red) wire

E. Bare (green) ground wire

F. Line 1 (black) wire

G. Metal ground strap

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut=off valve.

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 14" (36 crn) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Typical flexible connection

1. Apply pipe-joint compound made for use with LP gas to the

smaller thread ends of the flexible connector adapters (see C

and G in the following illustration).

2. Attach one adapter to the gas pressure regulator and the

other adapter to the gas shutoff valve. Tighten both adapters.

3. Use a 1%e"combination wrench and channel lock pliers to

attach the flexible connector to the adapters. Check that

connector is not kinked.

E F

A. V2"or 3/4"gas pipe

B. Manual gas shutoff valve

C. Use pipe-joint compound.

D. Adapter

E. Flexible connector

F Adapter (must have _/2"male

pipe thread)

G. Use pipe-joint compound.

H. Gas pressure regulator

Typical rigid pipe connection

A combination of pipe fittings must be used to connect the range

to the existing gas line. Your connections may be different,

according to the supply line type, size and location.

1. Apply pipe-joint compound made for use with LP gas to all

pipe thread connections.

2. Using a pipe wrench to tighten, connect the gas supply to the

range.

Complete Connection

1. Open the manual shutoff valve in the gas supply line. The

valve is open when the handle is parallel to the gas pipe.

A. Closed valve

B. Open valve

A. _/2"or 3/4"gas pipe

B. Manual gas shutoff valve

C. Nipple

D. Union

E. 90° elbow

F Black iron pipe

G. Union

H. Nipple

I.90 ° elbow (must have

_/2"male pipe thread)

J. Gas pressure regulator

Test all connections by brushing on an approved

noncorrosive leak-detection solution. If bubbles appear, a

leak is indicated. Correct any leak found.

Remove cooktop burner caps and grates from parts

package. Align notches in burner caps with pins in burner

base. Burner caps should be level when properly positioned.

If burner caps are not properly positioned, surface burners

will not light.

A. Burner base

B. Burner cap

C. Burner grate

Place burner grates over burners and caps as shown in the

following illustration. When properly installed, the grates

should not overlap the console.

Freestanding Ranges

Opening in grate for wok insert is located over left front

burner.

i iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii:i:...............

A.Opening in grate for wokinsert

Slide-In Ranges

Large flange with rounded corner must be at the rear corner

of the cooktop.

h_ ............................ll:..............................4

=7 '

.................................

IP/ If

,,F

II '41

A.Large flange with rounded corner

Plug in range or reconnect power. "Clock-Enter Time" should

appear in the display. For further information, please refer to

the user instructions located in the Use and Care Guide.

Initial lighting and gas flame adjustments

Cooktop burners use electronic igniters in place of standing

pilots. When the cooktop control knob is turned to the "LITE"

position, the system creates a spark to light the burner. This

sparking continues as long as the control knob is turned to

"LITE."

Check Operation of Cooktop Burners

Standard Surface Burners

Push in and turn each control knob to the "LITE" position.

The flame should light within 4 seconds. The first time a burner is

lit, it may take longer than 4 seconds to light because of air in the

gas line.

TripleTier _ Flame Burner

To start simmer burner:

Push in and turn control knob to "LITE."

The flame should light within 4 seconds. The first time a burner is

lit, it may take longer than 4 seconds to light because of air in the

gas line.

To start power burner:

Push in control knob again and turn to "POWER BURNER HI"

("DUAL HI" on model KDSS907XSP) to light the outer burner.

The flame should light within 4 seconds. The first time a burner is

lit, it may take longer than 4 seconds to light because of air in the

gas line.

If burners do not light properly:

• Turn cooktop control knob to the "OFF" position.

• Check that the range is plugged in and the circuit breaker has

not tripped or the household fuse has not blown.

• Check that the gas shutoff valves are set to the "open"

position.

• Check that burner caps are properly positioned on burner

bases.

Repeat start-up. If a burner does not light at this point, turn

control knobs to "Off" and contact your dealer or authorized

service company for assistance.

Adjust Flame Height

Adjust the height of top burner flames. The cooktop "low" burner

flame should be a steady blue flame approximately W' (0.64 cm)

high.

A. Low flame

B.High flame

To adjust standard burners:

The flame can be adjusted using the adjustment screw in the

center of the valve stem. The valve stem is located directly

underneath the control knob.

A. Valvestem

If the "low" flame needs to be adjusted:

1. Remove the control knob.

2. Hold the knob stem with a pair of pliers. Use a small flat-

blade screwdriver to turn the screw located in the center of

the control knob stem until the flame is the proper size.

3. Replace the control knob.

4. Test the flame by turning the control from "LO" to "HI,"

checking the flame at each setting.

To adjust TripleTier ®Flame burner:

1. Remove the control knob.

2. Insert a flat-blade screwdriver into adjustment locations

shown in the following illustration and engage the slotted

screw. Turn the screw until the flame is the proper size.

A. Simmer burner regulation

B. Power burner regulation

3. Replace the control knob.

4. Test the flame by turning the control from "LO" to "HI,"

checking the flame at each setting.

On models with a warming drawer:

1. Place your foot against the bottom front of the warming

drawer, and grasp the control panel and range top with two

hands as shown.

2. Slowly attempt to tilt the range forward.

If you encounter immediate resistance, the range foot is

engaged in the anti-tip bracket.

3. If the rear of the range lifts more than 1/2"(1.3 cm) off the floor

without resistance, stop tilting the range and lower it gently

back to the floor. The range foot is not engaged in the anti-tip

bracket.

IMPORTANT: If there is a snapping or popping sound when lifting

the range, the range may not be fully engaged in the bracket.

Check to see if there are obstructions keeping the range from

sliding to the wall or keeping the range foot from sliding into the

bracket. Verify that the bracket is held securely in place by the

mounting screws.

4. Slide the range forward, and verify that the anti-tip bracket is

securely attached to the floor or wall.

5. Slide range back so the rear range foot is inserted into the

slot of the anti-tip bracket.

IMPORTANT: If the back of the range is more than 2" (5.1 cm)

from the mounting wall, the rear range foot may not engage the

bracket. Slide the range forward and determine if there is an

obstruction between the range and the mounting wall. Changes

to the gas supply must be performed by a qualified service

technician. If you need assistance or service, refer to the cover or

the "Warranty" section of the User Instructions, for contact

information.

6. Repeat steps 1 and 2 to ensure that the range foot is

engaged in the anti-tip bracket.

If the rear of the range lifts more than 1/2"(1.3 cm) off the floor

without resistance, the anti-tip bracket may not be installed

correctly.

Place a rack in oven.

Place level on rack and check levelness of range, first side to

side; then front to back.

If range is not level, pull range forward until rear leveling leg is

removed from the anti-tip bracket.

Use a wrench or pliers to adjust leveling legs up or down until

the range is level. Push range back into position. Check that

rear leveling leg is engaged in the anti-tip bracket.

NOTE: Range must be level for satisfactory baking

performance.

Replace oven racks in oven cavity. Replace warming drawer or

storage drawer.

To Replace Warming Drawer:

1. Align the drawer glides with the receiving guides.

2. Push drawer in all the way.

3. Gently open and close the drawer to ensure it is seated

properly on the slides.

1. Check that all parts are now installed. If there is an extra part,

go back through the steps to see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. Check that range level. See the "Level Range" section.

5. Use a mild solution of liquid household cleaner and warm

water to remove waxy residue caused by shipping material.

Dry thoroughly with a soft cloth. For more information, see

the "Range Care" section of the Use and Care Guide.

6. Read the "Range Use" section in the Use and Care Guide.

7. Plug power cord into appropriate outlet. Slide range into its

final location. Check that the flexible conduit or power supply

cord are not bent.

8. Turn on surface burners and oven. See the Use and Care

Guide for specific instruction on range operation.

If range does not operate, check the following:

• Household fuse is intact and tight, or circuit breaker has not

tripped.

• Range is plugged into an outlet.

• Electrical supply is connected.

• See the "Troubleshooting" section in the Use and Care Guide.

9. When the range has been on for 5 minutes, check for heat. If

the range is cold, turn off the range and check that the gas

supply line shutoff valve is open.

• Ifthe gas supply line shutoff valve is closed, open it, then

repeat the 5-minute test as outlined above.

• If the gas supply line shutoff valve is open, close it, and

contact a qualified technician.

If you need Assistance or Service:

Please reference the "Assistance or Service" section of the

Use and Care Guide or contact the dealer from whom you

purchased your range.

GAS CONVERSIONS

Gas conversions from Natural gas to LP gas; or from LP gas to

Natural gas must be done by a qualified installer.

Explosion Hazard

Use a new CSA (nternational approved gas supply line.

Install a shut=off valve.

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 14" (36 cm) water

column.

Examples of a qua(ified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation

instructions.

Slide range back so rear range foot is engaged in the

slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed

and engaged.

Failure to follow these instructions can result in death

or serious burns to children and adults.

To Convert Gas Pressure Regulator

1. Turn manual shutoff valve to the "closed" position.

.................S

J_ ........................C

A. Torange

B. Manualshutoff valve "closed" position

C. Gassupply line

La page charge ...

KitchenAid KDSS907SSS05 Guide d'installation

Marque: KitchenAid

Modèle: KDSS907SSS05

Taper: Guide d'installation

Ce manuel convient également à

KDRS807SSS05

Télécharger le PDF

rapport

dans d''autres langues

English: KitchenAid KDSS907SSS05 Installation guide

KitchenAid KDSS907SSS05 Guide d'installation

Ce manuel convient également à

KitchenAid KDSS907SSS05 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents