Hikoki DH 40FR Manuel utilisateur

Marque: Hikoki

Modèle: DH 40FR

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Ce manuel convient également à

DH40FR

DOUBLE INSULATION

DOUBLE ISOLATION

AISLAMIENTO DOBLE

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la

mort ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce

produit. Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil

motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs et propriétaires

avant qu’ils utilisent l’outil motorisé. Ce mode d’emploi doit être conservé dans un

endroit sûr.

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily

injury!

This manual contains important information about product safety. Please read and

understand this manual BEFORE operating the power tool. Please keep this manual

available for other users and owners before they use the power tool. This manual should

be stored in safe place.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede

resultar en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y

comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual

para que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este

manual debe ser guardado en un lugar seguro.

Model Rotary Hammer

Modèle Marteau rotatif

Modelo Martillo perforador

DH 40FR

01Eng_DH40FR_US 5/25/12, 8:431

IMPORTANT SAFETY INFORMATION ................ 3

MEANINGS OF SIGNAL WORDS ........................ 3

SAFETY ...................................................................... 3

GENERAL POWER TOOL SAFETY WARNINGS .......

SPECIFIC SAFETY RULES AND SYMBOLS ......... 4

DOUBLE INSULATION FOR SAFER

OPERATION ................................................... 5

FUNCTIONAL DESCRIPTION .................................... 7

NAME OF PARTS .................................................. 7

SPECIFICATIONS .................................................. 7

ASSEMBLY AND OPERATION ................................. 8

APPLICATIONS ..................................................... 8

PRIOR TO OPERATION ......................................... 8

HOW TO USE ...................................................... 10

HOW TO USE THE CORE BIT ............................. 12

MAINTENANCE AND INSPECTION ....................... 14

ACCESSORIES ......................................................... 16

STANDARD ACCESSORIES ............................... 16

OPTIONAL ACCESSORIES ................................. 16

PARTS LIST .............................................................. 52

CONTENTS

English

Page Page

INFORMATIONS IMPORTANTES DE

SÉCURITÉ ..................................................... 19

SIGNIFICATION DES MOTS

D’AVERTISSEMENT .................................... 19

SECURITE ................................................................ 19

AVERTISSEMENTS DE SÉCURITÉ GÉNÉRAUX

CONCERNANT LES OUTILS ÉLECTRIQUES ......

REGLES DE SECURITE SPECIFIQUES ET

SYMBOLES .................................................. 21

DOUBLE ISOLATION POUR UN

FONCTIONNEMENT PLUS SUR ................. 22

DESCRIPTION FONCTIONNELLE ........................... 23

NOM DES PARTIES ............................................ 23

SPECIFICATIONS ................................................ 23

ASSEMBLAGE ET FONCTIONNEMENT ................ 24

APPLICATIONS ................................................... 24

AVANT L’UTILISATION ...................................... 24

UTILISATION ....................................................... 26

COMMENT UTILISER LA COURONNE .............. 28

ENTRETIEN ET INSPECTION .................................. 30

ACCESSOIRES ......................................................... 32

ACCESSOIRES STANDARD ............................... 32

ACCESSOIRES SUR OPTION ............................. 32

LISTA DES PIÈCES .................................................. 52

TABLE DES MATIERES

Français

Page Page

INFORMACIÓN IMPORTANTE SOBRE

SEGURIDAD ................................................. 35

SIGNIFICADO DE LAS PALABRAS DE

SEÑALIZACIÓN ............................................ 35

SEGURIDAD ............................................................. 35

ADVERTENCIAS DE SEGURIDAD GENERAL

DE LA HERRAMIENTA ELÉCTRICA ............ 35

NORMAS Y SÍMBOLOS ESPECÍFICOS DE

SEGURIDAD ................................................. 37

AISLAMIENTO DOBLE PARA OFRECER

UNA OPERACIÓN MÁS SEGURA .............. 38

DESCRIPCIÓN FUNCIONAL .................................... 39

NOMENCLATURA ............................................... 39

ESPECIFICACIONES ............................................ 39

MONTAJE Y OPERACIÓN ...................................... 40

APLICACIONES ................................................... 40

ANTES DE LA OPERACIÓN ................................ 40

MODO DE UTILIZACIÓN .................................... 42

MODO DE USAR LA BARRENA TUBULAR ....... 45

MANTENIMIENTO E INSPECCIÓN ........................ 47

ACCESORIOS ........................................................... 49

ACCESORIOS ESTÁNDAR ................................. 49

ACCESORIOS OPCIONALES .............................. 49

LISTA DE PIEZAS .................................................... 52

ÍNDICE

Español

Página Página

01Eng_DH40FR_US 5/25/12, 8:432

English

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual

before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic

safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation

before it occurs, and by observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections which

contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by WARNINGS on the

power tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been specifically recommended by HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate

injury, or may cause machine damage.

NOTE emphasizes essential information.

SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WARNING:

Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust.

Power tools create sparks which may ignite

the dust or fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools.

Unmodified plugs and matching outlets will

reduce risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators.

There is an increased risk of electric shock if

your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase the

risk of electric shock.

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts.

Damaged or entangled cords increase the risk

of electric shock.

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the influence of drugs, alcohol or

medication.

01Eng_DH40FR_US 5/25/12, 8:433

English

A moment of inattention while operating power

tools may result in serious personal injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing

protection used for appropriate conditions

will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or battery pack, picking

up or carrying the tool.

Carrying power tools with your finger on the

switch or energising power tools that have

the switch on invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left attached to a rotating part

of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of the power tool

in unexpected situations.

f) Dress properly. Do not wear loose clothing

or jewellery. Keep your hair, clothing and

gloves away from moving parts.

Loose clothes, jewellery or long hair can be

caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used.

Use of dust collection can reduce dust-related

hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application.

The correct power tool will do the job better

and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and off.

Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools.

Such preventive safety measures reduce the

risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for

misalignment or binding of moving parts,

breakage of parts and any other condition

that may affect the power tool’s operation.

If damaged, have the power tool repaired

before use.

Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are

easier to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed.

Use of the power tool for operations different

from those intended could result in a

hazardous situation.

5) Service

a) Have your power tool serviced by a qualified

repair person using only identical

replacement parts.

This will ensure that the safety of the power

tool is maintained.

SPECIFIC SAFETY RULES AND SYMBOLS

1. Wear ear protectors.

Exposure to noise can cause hearing

loss.

2. Use auxiliary handles, if supplied with the tool.

Loss of control can cause personal injury.

3. Hold power tools by insulated gripping surfaces

when performing an operation where the cutting

tool may contact hidden wiring or its own cord.

Cutting accessory contacting a “live” wire may

make exposed metal parts of the power tool “live”

and could give the operator an electric shock.

4. NEVER touch the tool bit with bare hands after

operation.

5. NEVER wear gloves made from materials likely to

roll up such as cotton, wool, cloth or string, etc.

6. ALWAYS attach the side handle and securely grip

the Demolition Hammer.

7. NEVER touch moving parts.

NEVER place your hands, fingers or other body

parts near the tool’s moving parts.

8. NEVER operate without all guards in place.

NEVER operate this tool without all guards or

safety features in place and in proper working

order. If maintenance or servicing requires the

removal of a guard or safety feature, be sure to

replace the guard or safety feature before resuming

operation of the tool.

9. Use right tool.

Don’t force small tool or attachment to do the job

of a heavy-duty tool.

01Eng_DH40FR_US 5/25/12, 8:434

English

Don’t use tool for purpose not intended —for

example— don’t use circular saw for cutting tree

limbs or logs.

10. NEVER use a power tool for applications other

than those specified.

NEVER use a power tool for applications other than

those specified in the Instruction Manual.

11. Handle tool correctly.

Operate the tool according to the instructions

provided herein. Do not drop or throw the tool.

NEVER allow the tool to be operated by children,

individuals unfamiliar with its operation or

unauthorized personnel.

12. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted.

Check their condition periodically.

13. Do not use power tools if the plastic housing or

handle is cracked.

Cracks in the tool’s housing or handle can lead to

electric shock. Such tools should not be used until

repaired.

14. Blades and accessories must be securely mounted

to the tool.

Prevent potential injuries to yourself or others.

Blades, cutting implements and accessories which

have been mounted to the tool should be secure

and tight.

15. Keep motor air vent clean.

The tool’s motor air vent must be kept clean so

that air can freely flow at all times. Check for dust

build-up frequently.

16. Operate power tools at the rated voltage.

Operate the power tool at voltages specified on its

nameplate.

If using the power tool at a higher voltage than

the rated voltage, it will result in abnormally fast

motor revolution and may damage the unit and

the motor may burn out.

17. NEVER use a tool which is defective or operating

abnormally.

If the tool appears to be operating unusually,

making strange noises, or otherwise appears

defective, stop using it immediately and arrange

for repairs by a Hitachi authorized service center.

18. NEVER leave tool running unattended. Turn power

off.

Don’t leave tool until it comes to a complete stop.

19. Carefully handle power tools.

Should a power tool be dropped or struck against

hard materials inadvertently, it may be deformed,

cracked, or damaged.

20. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon

tetrachloride, and alcohol may damage and crack

plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly

dampened with soapy water and dry thoroughly.

21. ALWAYS wear eye protection that meets the

requirement of the latest revision of

ANSI Standard Z87.1.

22. ALWAYS be careful with buried object such as an

underground wiring.

Touching live wiring or electric cable with this tool

may result in electric shock.

Confirm before use whether hidden objects are

present, such as electric cables within the wall,

floor or ceiling.

23. Definitions for symbols used on this tool

V ............... volts

Hz ............. hertz

A ............... amperes

o .............. no load speed

W .............. watt

............. Class II Construction

---/min ...... revolutions per minute

.............. Alternating current

DOUBLE INSULATION FOR SAFER

OPERATION

To ensure safer operation of this power tool, HITACHI

has adopted a double insulation design. “Double

insulation” means that two physically separated

insulation systems have been used to insulate the

electrically conductive materials connected to the power

supply from the outer frame handled by the operator.

Therefore, either the symbol “ ” or the words “Double

insulation” appear on the power tool or on the

nameplate.

Although this system has no external grounding, you

must still follow the normal electrical safety precautions

given in this Instruction Manual, including not using

the power tool in wet environments.

To keep the double insulation system effective, follow

these precautions:

䡬

Only HITACHI AUTHORIZED SERVICE CENTER

should disassemble or assemble this power tool,

and only genuine HITACHI replacement parts

should be installed.

䡬

Clean the exterior of the power tool only with a

soft cloth moistened with soapy water, and dry

thoroughly.

Never use solvents, gasoline or thinners on plastic

components; otherwise the plastic may dissolve.

01Eng_DH40FR_US 7/26/12, 11:385

English

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO OTHER USERS

AND

OWNERS OF THIS TOOL!

01Eng_DH40FR_US 5/25/12, 8:436

English

Fig. 1

Housing

Stopper

Tool Holder

Switch Trigger

Side Handle

Handle

Nameplate

Tail Cover

Set Screw

(Under the

Tail Cover)

Selector Lever

Brush Cap

(Inside the Tail Cover)

Dial

Motor Single-Phase, Series Commutator Motor.

Power Source Single-Phase, 120 V 60 Hz

Current 9.2 A

Capacity Drill Bit: 1-9/16" (40 mm)

Core Bit: 4-1/8" (105 mm)

No-Load Speed 240 – 480/min

Full-load Blow 1320 – 2650/min

Weight 14.3 lbs (6.5 kg)

Drill Bit

FUNCTIONAL DESCRIPTION

NOTE: The information contained in this Instruction Manual is designed to assist you in

the safe operation and maintenance of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have first read

and understood all safey instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that

differ from those on your own power tool.

NAME OF PARTS

SPECIFICATIONS

01Eng_DH40FR_US 5/25/12, 8:437

English

ASSEMBLY AND OPERATION

APPLICATIONS

Rotation and hammering function

䡬 Drilling anchor holes

䡬 Drilling holes in concrete

Hammering function only

䡬 Crushing concrete, chipping, digging, and squaring

(by applying optional accessories)

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms to the power source requirements

specified on the product nameplate.

2. Power switch

Ensure that the switch is in the OFF position. If the plug is connected to a receptacle

while the switch is in the ON position, the power tool will start operating immediately

and can cause serious injury.

3. Extension cord

When the work area is far away from the power source, use an extension cord of

sufficient thickness and rated capacity. The extension cord should be kept as short as

practicable.

WARNING:

Damaged cord must be replaced or repaired.

4. Check the receptacle

If the receptacle only loosely accepts the plug, the receptacle must be repaired. Contact

a licensed electrician to make appropriate repairs.

If such a faulty receptacle is used, it may cause overheating, resulting in a serious

hazard.

5. Confirming condition of the environment:

Confirm that the work site is placed under appropriate conditions conforming to

prescribed precautions.

01Eng_DH40FR_US 7/26/12, 11:388

English

6. How to install dust cover (Fig. 2)

Always install the dust cover on the drill bit or

the taper shank adaptor. Insert the dust cover

until it lies flush in the groove.

NOTE: For a thick drill bit, insert the dust cover

from drill rear.

7. How to install tool

CAUTION:

For tools such as a drill bit and a bull point, use only Hitachi genuine parts.

(1) Clean, then smear the tool shank with the

grease provided in the green tube.

(2) Pull the tool holder in the direction of arrow 1

and rotate it in the direction of arrow 2

(counterclockwise). Fully insert the tool shank

into the hexagonal hole of the front cover. (Fig.

(3) Return the tool holder to fix the tool.

(4) Pull the tool to make sure it is locked

completely.

NOTE: Remove in the reverse order to

installation.

8. Regulating the number of rotations and

hammering (Fig. 4)

This Rotary Hammer is equipped with a built-

in electronic control circuit that can adjust and

regulate the number of rotations and times of

hammering. This Rotary Hammer can be used

by adjusting the dial, depending upon the

contents of operation, such as boring holes into

fragile materials, chipping, centering, etc.

The scale ‘1’ of the dial is designed for a

minimum speed with the number of 240

rotations per minute and 1320 times of blow

per minute. The scale ‘6’ is designed for a

maximum speed with the number of 480

rotations per minute and 2650 times of blow

per minute.

CAUTION:

Do not adjust the dial during operation. Doing so can result in injury because the

Rotary Hammer must be held by only one hand, disabling the steady control of the

Rotary Hammer.

Fig. 3

Tool Holder

Tool Shank

Dial

Fig. 4

Fig. 2

Dust cover

Insert up to the

groove

Front Cover

01Eng_DH40FR_US 5/25/12, 8:439

English

Fig. 6

Fig. 5

Fig. 7

Selector Lever

Lever Holder

Button

HOW TO USE

1. How to drill holes (Fig. 5)

(1) Pull the switch trigger after applying the drill

bit tip to the drilling position.

(2) It is unnecessary to forcibly press the Rotary

Hammer main body. It is sufficient to slightly

press the rotary hammer to an extent that clips

are freely discharged.

CAUTION:

Although this machine is equipped with a

safety clutch, if the drill bit becomes bound in

concrete or other material, the resultant

stoppage of the drill bit could cause the

machine body to turn in reaction. Ensure that

the main handle and side handle are gripped

firmly during operation.

2. How to chisel or crush (Fig. 6)

By applying the tool tip to the chiseling or

crushing position, operate the rotary hammer

by utilizing its empty weight. Forcible pressing

or thrusting is unnecessary.

3. When drilling at “rotation + hammering”

CAUTION:

If you switch the selector lever during motor

rotation, the tool can start to rotate abruptly,

resulting in unexpected accidents. Be sure to

switch the selector lever when the motor is at

a complete stop.

(1) Switching to “rotation + hammering”

(a) Push the button, release lock and turn the

selector lever clockwise.

(b) Align

of the selector lever and of the

lever holder as illustrated in Fig. 7.

lever.

NOTE: Turn the selector lever (do not push the button) to check if it is completely locked

and make sure that it does not turn.

01Eng_DH40FR_US 5/25/12, 8:4310

English

Lever HolderSelector Lever

Fig. 8

Stopper

Side Handle

Fig. 9

Button

Fig. 10

4. When chipping and shredding at “hammering”:

CAUTION:

䡬 If the selector lever is switched during motor rotation, the tool can start to rotate

abruptly, resulting in unexpected accidents. Make sure to switch the selector lever

when the motor is at a complete stop.

(1) Switching to “hammering”

(a) Push the button, release lock and turn the

selector lever counterclockwise.

(b) Align

of the selector lever and of the

lever holder as illustrated in Fig. 8.

lever.

NOTE: Turn the selector lever (do not push

the button) to check if it is completely

locked and make sure that it does not

turn.

5. Install the stopper (Fig. 9)

(1) Loosen the side handle and insert the straight

portion of the stopper into the handle bolt hole

from the front cover.

(2) Loosen the side handle, move the stopper to

the specified position and rotate the grip of the

side handle clockwise to fix the stopper.

6. Warming up (Fig. 10)

The grease lubrication system in this unit may

require warming up in cold regions.

Position the end of the bit so makes contact

with the concrete, turn on the switch and

perform the warming up operation. Make sure

that a hitting sound is produced and then use

the unit.

CAUTION:

When the warming up operation is performed,

hold the side handle and the main body

securely with both hands to maintain a secure

grip and be careful not to twist your body by

the jammed drill bit.

01Eng_DH40FR_US 5/25/12, 8:4311

English

Fig. 11

Drill Bit

(Taper shank)

Taper Shank Adaptor

Fig. 14

Taper Shank

Adaptor

Cotter

Support

Fig. 12

Fig. 15

Center Pin

Core Bit

Core Bit Tip

Guide Plate

Fig. 13

Core Bit

Core Bit Shank

7. How to use the drill bit (taper shank) and

the taper shank adaptor.

(1) Install drill bit with taper shank in the taper

shank adaptor. (Fig. 11)

(2) Turn the power on and drill a base hole.

(3) After cleaning out dust with a syringe, attach

the plug to the anchor tip and drive in the

anchor with a manual hammer.

(4) To remove the drill bit with taper shank, insert

a cotter into the slot of the taper shank adaptor,

place supports under the Rotary Hammer and

tap the cotter with a manual hammer. (Fig. 12)

HOW TO USE THE CORE BIT

When boring penetrating large hole use the core bit. At that time use with the center pin

and the core bit shank provided as optional accessories.

1. Mounting

CAUTION:

Be sure to turn power OFF and disconnect the plug from the receptacle.

(1) Mount the core bit to the core bit shank. (Fig. 13)

Lubricate the thread of the core bit shank to facilitate disassembly.

(2) Mount the core bit shank to the Rotary Hammer. (Fig. 14)

(3) Insert the center pin into the guide plate until it stops.

(4) Engage the guide plate with the core bit, and turn the guide plate to left or right so that

it does not fall even if it faces downward. (Fig. 15)

01Eng_DH40FR_US 5/25/12, 8:4312

English

Fig. 16

Core Bit

Shank

Fig. 17

2. How to bore (Fig. 16)

(1) Connect the plug to the receptacle.

(2) A spring is installed in the center pin. Push it

lightly to the wall or the floor straight. Connect

all over the surface of the core bit tip and start

operating.

(3) When boring about 3/16" (5 mm) in depth the

position of the hole will establish. Bore after

that removing the center pin and the guide

plate from core bit.

(4) Application of excessive force will not only

expedite the work, but will deteriorate the tip

edge of the drill bit, resulting in reduced service

life of the rotary hammer.

CAUTION:

When removing the center pin and the guide

plate, turn OFF the switch and disconnect the

plug from the receptacle.

3. Dismounting (Fig. 17)

Remove the core bit shank from the rotary

hammer and strike the head of the core bit

shank strongly two or three times with a

manual hammer holding the core bit, then the

thread becomes loose and the core bit can be

removed.

01Eng_DH40FR_US 5/25/12, 8:4313

English

Wear limit

No. of carbon brush

0.28" (7 mm)

0.67" (17 mm)

MAINTENANCE AND INSPECTION

WARNING: Be sure to switch power OFF and disconnect the plug from the

receptacle during maintenance and inspection.

1. Inspecting the drill bits

Since use of a dull tool will cause motor malfunctioning and degraded efficiency, replace

the drill bit with a new one or resharpening without delay when abrasion is noted.

2. Inspecting the screws

Regularly inspect all screws and ensure that they are properly tightened. Should any of

the screws be loose, retighten them immediately.

WARNING: Using this Rotary Hammer with loosen screws is extremely dangerous.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power tool. Exercise due care to

ensure the winding does not become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes: (Fig. 18)

The motor employs carbon brushes which are consumable parts. When they become

worn to or near “wear limit”, it could result in motor trouble. When an auto-stop carbon

brush is equipped, the motor will stop automatically. At that time, replace both carbon

brushes with new ones which have the same carbon brush Nos. shown in the figure.

In addition, always keep carbon brushes clean and ensure that they slide freely within

the brush holders.

CAUTION:

Using this Rotary Hammer with a carbon brush which is worn in excess of the wear

limit will damage the motor.

Fig. 18

NOTE: Use HITACHI carbon brush No.73 indicated in Fig. 18

01Eng_DH40FR_US 5/25/12, 8:4314

English

Crank Cover

Fig. 19

䡬 Replacing carbon brushes:

(For parts name, refer to Fig. 1)

Loosen the two set screws and remove the tail cover. Remove the brush caps and

carbon brushes. After replacing the carbon brushes, tighten the brush caps securely

and to install the tail cover with securely tightening two set screws.

5. How to replase grease

This machine is full air-tight construction to protect against dust and to prevent lubricant

leakage. Therefore, the machine can be used without lubrication for long periods.

Replace the grease as described below.

䡬 Grease replacement period

After purchase, replace grease after every 6 months of usage. Ask for grease replacement

at the nearest HITACHI Authorized Service Center. Proceed for replacement of grease.

䡬 Grease replenishment

CAUTION:

Before replenishing the grease, turn the power off and pull out the power plug.

(1) Remove the crank cover and wipe off the

grease inside.

(2) Apply 1.0 oz (30 g) of HITACHI Electric Hammer

Grease A (standard accessory, contained in

tube) to the crank case.

(3) After replenishing the grease, install the crank

cover securely.

NOTE: The HITACHI Electric Hammer Grease

A is of the lower viscosity type. When

the supplied grease tube is consumed,

purchase from a HITACHI Autorized

Service Center.

6. Service and repairs

All quality power tools will eventually require servicing or replacement of parts because

of wear from normal use. To assure that only authorized replacement parts will be

used, all service and repairs must be performed by a HITACHI AUTHORIZED SERVICE

CENTER, ONLY.

01Eng_DH40FR_US 5/25/12, 8:4315

English

Overall length

16"(400 mm)

Code No.

985375

985376

External dia.

1" (25 mm)

1-1/2" (38 mm)

(1) Drill bit (Spline shank)

ACCESSORIES

WARNING: ALWAYS use Only authorized HITACHI replacement parts and

accessories. NEVER use replacement parts or accessories which are

not intended for use with this tool. Contact HITACHI if you are not sure

whether it is safe to use a particular replacement part or accessory

with your tool.

The use of any other attachment or accessory can be dangerous and

could cause injury or mechanical damage.

NOTE: Accessories are subject to change without any obligation on the part of the HITACHI.

STANDARD ACCESSORIES

(1) Case (Molded plastic) (Code No. 322152).......................................................................... 1

(2) Side Handle (Code No. 313078).......................................................................................... 1

(3) Stopper (Code No. 971786)................................................................................................. 1

(4) Hammer Grease A (Code No. 981840) ............................................................................... 1

(5) Dust Cover (Code No. 993245) ........................................................................................... 1

OPTIONAL ACCESSORIES.....sold separately

For accessories in detail please call HITACHI AT 1-800-59-TOOLS

1. Through-hole drilling (Rotation + Hammering)

01Eng_DH40FR_US 5/25/12, 8:4316

English

2. Anchor hole drilling (Rotation + Hammering)

(2) Taper shank adaptor

3. Large-dia. hole boring (Rotation + Hammering)

4. Crushing (Hammering)

5. Groove digging and edging (Hammering)

Taper shank adaptor formed

A-taper or B-taper is provided as

optional accessory, but drill bit for

it is not provided

Code No. 985377

Code No. 985378

A-taper

B-taper

(1) Drill bit

(Taper shank)

(3) Cotter (Code No. 944477)

(2) Taper shank adaptor

(Spline shank)

(Guide plate)

Code No.

985388

955169

(2) Core bit

External dia.

2" (50 mm)

4-1/8" (105 mm)

(1) Center pin

Code No.

955165

(3) Core bit shank

(Spline shank)

(1) Cold chisel

Overall length Code No.

12" (300 mm) 985381

18" (460 mm) 985382

(1) Bull point

Overall length Code No.

12" (300 mm) 985383

01Eng_DH40FR_US 5/25/12, 8:4317

English

(1) Cutter

Overall length Width Code No.

12" (300 mm)

1-1/2" (38 mm) 985384

2" (50 mm) 985385

(1) Scoop

Code No. 985386

6. Asphalt cutting (Hammering)

7. Digging

8. Syringe (for chip removal)

NOTE: Specifications are subject to change without any obligation on the part of the

HITACHI.

Code No. 985386

Code No. 320859

Code No. 318085

01Eng_DH40FR_US 5/25/12, 8:4318

Français

INFORMATIONS IMPORTANTES DE SÉCURITÉ

Lire et comprendre toutes les précautions de sécurité, les avertissements et les instructions de fonctionnement

dans ce mode d’emploi avant d’utiliser ou d’entretenir cet outil motorisé.

La plupart des accidents causés lors de l’utilisation ou de l’entretien de l’outil motorisé proviennent d’un non

respect des règles ou précautions de base de sécurité. Un accident peut la plupart du temps être évité si l’on

reconnaît une situation de danger potentiel avant qu’elle ne se produise, et en observant les procédures de sécurité

appropriées.

Les précautions de base de sécurité sont mises en évidence dans la section “SECURITE” de ce mode d’emploi et

dans les sections qui contiennent les instructions de fonctionnement et d’entretien.

Les dangers qui doivent être évités pour prévenir des blessures corporelles ou un endommagement de la machine

sont identifiés par AVERTISSEMENTS sur l’outil motorisé et dans ce mode d’emploi.

NE JAMAIS utiliser cet outil motorisé d’une manière qui n’est pas spécifiquement recommandée par HITACHI.

SIGNIFICATION DES MOTS D’AVERTISSEMENT

AVERTISSEMENT indique des situations potentiellement dangereuses qui, si elles sont ignorées, pourraient

entraîner la mort ou de sérieuses blessures.

PRECAUTION indique des situations dangereuses potentilles qui, si elles ne sont pas évitées, peuvent entraîner

de mineures et légères blessures ou endommager la machine.

REMARQUE met en relief des informations essentielles.

SECURITE

AVERTISSEMENTS DE SÉCURITÉ GÉNÉRAUX CONCERNANT LES OUTILS ÉLECTRIQUES

AVERTISSEMENT :

Lire tous les avertissements de sécurité et toutes les instructions

Tout manquement à observer ces avertissements et instructions peut engendrer des chocs électriques, des

incendies et/ou des blessures graves.

Conservez tous les avertissements et toutes les instructions pour vous y référer ultérieurement.

Le terme "outil électrique", utilisé dans les avertissements, se réfère aux outils électriques (câblé) ou aux

outils à piles (sans fil).

1) Sécurité de l’aire de travail

a) Maintenir l'aire de travail propre et bien

éclairée.

Les endroits encombrés ou sombres sont

propices aux accidents.

b) Ne pas utiliser d'outils électriques en présence

de liquides, gaz ou poussière inflammables,

au risque de provoquer une explosion.

Les outils électriques créent des étincelles

susceptibles d'enflammer la poussière.

c) Ne pas laisser les enfants et les visiteurs

s'approcher de vous lorsque vous utiliser un

outil électrique.

Les distractions peuvent faire perdre le contrôle.

2) Sécurité électrique

a) Les prises de l'outil électrique doivent

correspondre à la prise secteur.

Ne jamais modifier la prise.

Ne pas utiliser d'adaptateurs avec les outils

électriques mis à la masse.

Les prises non modifiées et les prises secteurs

correspondantes réduisent les risques de

choc électrique.

b) Eviter tout contact avec les surfaces mises à

la masse telles que les tuyaux, radiateurs,

bandes et réfrigérateurs.

Le risque de choc électrique est accru en cas

de mise à la masse du corps.

c) Ne pas exposer les outils électriques à la pluie

ou à des conditions humides.

Si l'eau pénètre dans l'outil, cela augmente

les risques de choc électrique.

d) Ne pas utiliser le cordon à tort. Ne jamais

utiliser le cordon pour transporter ou

débrancher l'outil électrique.

Maintenir le cordon loin de la chaleur, de

l'huile, des bords pointus ou des pièces

mobiles.

Les cordons endommagés ou usés

augmentent les risques de choc électrique.

02Fre_DH40FR_US 5/25/12, 8:4419

Français

e) En cas d'utilisation d'un outil électrique à

l'extérieur, utiliser un cordon de rallonge

adapté à un usage extérieur.

L'utilisation d'un cordon adapté à l'usage

extérieur réduit les risques de choc électrique.

f) Si vous devez utiliser un outil électrique dans

un endroit humide, utilisez une alimentation

protégée contre les courants résiduels.

L'utilisation d'un dispositif de protection

contre les courants résiduels réduit le risque

de choc électrique.

3) Sécurité personnelle

a) Restez alerte, regarder ce que vous faites et

usez de votre bon sens en utilisant un outil

électrique.

Ne pas utiliser d'outil électrique si vous êtes

sous l'influence de drogues, d'alcool ou de

médicaments.

Pendant l'utilisation d'outils électrique, un

instant d'inattention peut entraîner des

blessures graves.

b) Utiliser un équipement de protection

individuelle. Toujours porter des verres de

protection.

L'utilisation d'équipements de protection tels

que les masques anti-poussière, les chaussures

de sécurité anti-dérapantes, les casques ou les

protections auditives dans des conditions

appropriées réduisent les risques de blessures.

c) Empêcher les démarrages intempestifs.

Veiller à ce que l'interrupteur soit en position

d'arrêt avant de brancher à une source

d'alimentation et/ou une batterie, de

ramasser l'outil au sol ou de le transporter.

Transporter les outils électriques avec le doigt

sur l'interrupteur ou brancher les outils

électriques avec l'interrupteur en position de

marche peut entraîner des accidents.

d) Retirer toute clé de sécurité ou clé avant de

mettre l'outil électrique en marche.

Laisser une clé ou une clé de sécurité sur une

partie mobile de l'outil électrique peut

engendrer des blessures.

e) Ne pas trop se pencher. Toujours garder une

bonne assise et un bon équilibre pendant le

travail.

Cela permet un meilleur contrôle de l'outil

électrique dans des situations imprévisibles.

f) Porter des vêtements adéquats. Ne pas

porter de vêtements amples ni de bijoux.

Maintenir les cheveux, les vêtements et les

gants loin des pièces mobiles.

Les vêtements amples ou les cheveux longs

peuvent se prendre dans les pièces mobiles.

g) En cas de dispositifs destinés au

raccordement d'installations d'extraction et

de recueil de la poussière, veiller à ce qu'ils

soient correctement raccordés et utilisés.

L'utilisation d'un dispositif de collecte de la

poussière peut réduire les dangers associés

à la poussière.

4) Utilisation et entretien d'un outil électrique

a) Ne pas forcer sur l'outil électrique. Utiliser

l'outil électrique adapté à vos travaux.

Le bon outil électrique fera le travail mieux et

en toute sécurité au régime pour lequel il a

été conçu.

b) Ne pas utiliser l'outil électrique si

l'interrupteur ne le met pas en position de

marche et d'arrêt.

Tout outil ne pouvant être contrôlé par

l'interrupteur est dangereux et doit être réparé.

c) Débrancher la prise ou retirer la batterie avant

de procéder à des réglages, au remplacement

des accessoires ou au stockage des outils

électriques.

Ces mesures préventives de sécurité

réduisent les risques de démarrage accidentel

de l'outil électrique.

d) Stockez les outils électriques inutilisés hors

de la portée des enfants et ne pas laisser des

personnes non familiarisées avec l'outil ou

ces instructions utiliser l'outil électrique.

Les outils électriques sont dangereux entre

les mains d'utilisateurs non habilités.

e) Entretenir les outils électriques. Vérifier

l'absence de mauvais alignement ou d'arrêt,

d'endommagement de pièces ou toute autre

condition susceptible d'affecter l'opération de

l'outil.

Si l'outil est endommagé, le faire réparer

avant utilisation.

De nombreux accidents sont dus à des outils

mal entretenus.

f) Maintenir les outils coupants aiguisés et

propres.

Des outils coupants bien entretenus avec des

bords aiguisés sont moins susceptibles de se

coincer et plus simples à contrôler.

g) Utiliser l'outil électrique, les accessoires et

les mèches de l'outil, etc. conformément à

ces instructions en tenant compte des

conditions d'utilisation et du travail à réaliser.

L'utilisation de l'outil électrique pour des

opérations différentes de celles pour

lesquelles il a été conçu est dangereuse.

5) Service

a) Faire entretenir l'outil électrique par un

technicien habilité à l'aide de pièces de

rechange identiques exclusivement.

Cela garantira le maintien de la sécurité de

l'outil électrique. lesquelles il a été conçu est

dangereuse.

02Fre_DH40FR_US 5/25/12, 8:4420

La page charge ...

Hikoki DH 40FR Manuel utilisateur

Marque: Hikoki

Modèle: DH 40FR

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Ce manuel convient également à

DH40FR

Télécharger le PDF

rapport

dans d''autres langues

English: Hikoki DH 40FR User manual
español: Hikoki DH 40FR Manual de usuario

Hikoki DH 40FR Manuel utilisateur

Ce manuel convient également à

Hikoki DH 40FR Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents