Toro Flex-Force Power System 60V Stick Edger Manuel utilisateur

Form No. 3461-1 15 Rev A

Flex-Force Power System™ 60V Stick Edger

51833 , 51833T

Cortabordes Flex-Force Power System™ 60 V

51833 , 51833T

Coupe-bordures à manche Flex-Force Power

System™ de 60 V

51833 , 51833T

www .T oro.com.

*3461-115*

Form No. 3461-1 12 Rev A

Flex-Force Power System

™

60V

Stick Edger

Model No. 51833 —Serial No. 323000001 and Up

Model No. 51833T —Serial No. 323000001 and Up

Register at www .T oro.com.

Original Instructions (EN)

*3461-112*

For assistance, please see

www .T oro.com/support

for instructional videos

or contact 1-888-384-9939

before returning this

product.

W ARNING

CALIFORNIA

Proposition 65 W arning

The power cord on this product contains

lead, a chemical known to the State

of California to cause birth defects

or other reproductive harm. W ash

hands after handling.

Use of this product may cause exposure

to chemicals known to the State of

California to cause cancer , birth defects,

or other reproductive harm.

Introduction

This edger is intended to be used by residential

homeowners to trim grass around the edge of

driveways, sidewalks, and more as needed outdoors.

It is designed to use T oro 60V lithium-ion battery

packs. These battery packs are designed to be

charged only by T oro 60V lithium-ion battery chargers.

Using this product for purposes other than its intended

use could prove dangerous to you and bystanders.

Model 51833T does not include a battery or a

charger .

Read this information carefully to learn how to operate

and maintain your product properly and to avoid

injury and product damage. Y ou are responsible for

operating the product properly and safely .

V isit www .T oro.com for product safety and operation

training materials, accessory information, help nding

a dealer , or to register your product.

Whenever you need service, genuine the

manufacturer parts, or additional information, contact

an Authorized Service Dealer or the manufacturer

Customer Service and have the model and serial

numbers of your product ready . Figure 1 identies

the location of the model and serial numbers on the

product. W rite the numbers in the space provided.

Important: W ith your mobile device, you can

scan the QR code on the serial number decal (if

equipped) to access warranty , parts, and other

product information.

g428616

Figure 1

1. Model and serial number location

Model No.

Serial No.

81 1 1 L yndale A venue South

Bloomington, MN 55420

2

Contact us at www .T oro.com.

Printed in China

Safety-Alert Symbol

The safety-alert symbol ( Figure 2 ) shown in this

manual and on the machine identies important safety

messages that you must follow to prevent accidents.

g000502

Figure 2

Safety-alert symbol

The safety-alert symbol appears above information

that alerts you to unsafe actions or situations and

is followed by the word DANGER ,W ARNING , or

CAUTION .

DANGER indicates an imminently hazardous situation

which, if not avoided, will result in death or serious

injury .

W ARNING indicates a potentially hazardous situation

which, if not avoided, could result in death or serious

injury .

CAUTION indicates a potentially hazardous situation

which, if not avoided, may result in minor or moderate

injury .

This manual uses two other words to highlight

information. Important calls attention to special

mechanical information and Note emphasizes general

information worthy of special attention.

Safety

IMPORT ANT SAFETY

INSTRUCTIONS

W ARNING

When using electric gardening tools, always

read and follow basic safety warnings and

instructions to reduce the risk of re, electric

shock, and personal injury , including the

following:

Read All Instructions

I. T raining

1. The operator of the tool is responsible for any

accidents or hazards occurring to others or their

property .

2. Do not allow children to use or play with the

tool, battery pack, or the battery charger; local

regulations may restrict the age of the operator .

3. Do not allow children or untrained people to

operate or service this device. Allow only people

who are responsible, trained, familiar with the

instructions, and physically capable to operate

or service the device.

4. Before using the tool, battery pack, and battery

charger , read all the instructions and cautionary

markings on these products.

5. Become familiar with the controls and proper use

of the tool, battery pack, and battery charger .

II. Preparation

1. Keep bystanders and children away from the

operating area.

2. Use only the battery pack specied by T oro.

Using other accessories and attachments may

increase the risk of injury and re.

3. Plugging the battery charger into an outlet that is

not 120 V can cause a re or electric shock. Do

not plug the battery charger into an outlet other

than 120 V . For a dif ferent style of connection,

use an attachment plug adapter of the proper

conguration for the power outlet if needed.

4. Do not use a damaged or modied battery

pack or battery charger , which may exhibit

unpredictable behavior that results in re,

explosion, or risk of injury .

5. If the supply cord to the battery charger is

damaged, contact an Authorized Service Dealer

to replace it.

6. Charge the battery pack with only the battery

charger specied by T oro. A charger suitable for

3

1 type of battery pack may create a risk of re

when used with another battery pack.

7. Charge the battery pack in a well-ventilated area

only .

8. Follow all charging instructions and do

not charge the battery pack outside of the

temperature range specied in the instructions.

Otherwise, you may damage the battery pack

and increase the risk of re.

9. Do not operate the tool without all guards and

other safety protective devices in place and

functioning properly on the tool.

10. Dress properly—W ear appropriate clothing,

including eye protection; long pants; substantial,

slip-resistant footwear; rubber gloves; and

hearing protection. T ie back long hair and do

not wear loose clothing or loose jewelry that can

get caught in moving parts. W ear a dust mask in

dusty operating conditions.

III. Operation

1. A void dangerous environments—Do not use the

tool in rain or in damp or wet locations.

2. Use the proper tool for your application—Using

the tool for purposes other an its intended use

could prove dangerous to you and bystanders.

3. Prevent unintentional starting—Ensure that the

switch is in the O FF position before connecting

to the battery pack and handling the tool. Do

not carry the tool with your nger on the switch

or energize the tool with the switch in the O N

position.

4. Operate the tool only in daylight or good articial

light.

5. If the tool strikes an object or starts to vibrate,

immediately shut of f the tool, wait for all moving

parts to stop, and disconnect the battery before

examining the tool for damage. Make all

necessary repairs before resuming operation

6. Remove the battery pack from the tool before

adjusting it or changing accessories.

7. Keep your hands and feet away from the cutting

area and all moving parts.

8. Shut of f the tool, remove the battery pack from

the tool, and wait for all movement to stop before

adjusting, servicing, cleaning, or storing the tool.

9. Remove the battery pack from the tool whenever

you leave it unattended.

10. Do not force the tool—Allow the tool to do the

job better and safer at the rate for which it was

designed.

1 1. Do not overreach—Keep proper footing and

balance at all times, especially on slopes. W alk,

never run with the tool.

12. Stay alert—W atch what you are doing and use

common sense when operating the tool. Do not

use the tool while ill, tired, or under the inuence

of alcohol or drugs.

13. Ensure that the ventilation openings are kept

clear of debris.

14. Under abusive conditions, the battery pack may

eject liquid; avoid contact. If you accidently

come into contact with the liquid, ush with

water . If the liquid contacts your eyes, seek

medical help. Liquid ejected from the battery

pack may cause irritation or burns.

15. Do not expose a battery pack or tool to re or

excessive temperature. Exposure to re or

temperature above 130°C (265°F) may cause

explosion.

16. CAUTION—A mistreated battery pack may

present a risk of re, explosion, or chemical

burn.

•Do not disassemble the battery pack.

•Replace the battery pack with a genuine

T oro battery pack only; using another type of

battery pack may cause a re or risk of injury .

•Keep battery packs out of the reach of

children and in the original packaging until

you are ready to use them.

IV . Maintenance and Storage

1. Maintain the tool with care—Keep it clean and

in good repair for best performance and to

reduce the risk of injury . Follow the instructions

for lubricating and changing accessories. Keep

handles dry , clean, and free from oil and grease.

2. When the battery pack is not in use, keep it

away from metal objects such as paper clips,

coins, keys, nails, and screws that can make a

connection from 1 terminal to another . Shorting

the battery terminals may cause burns or a re.

3. Keep your hands and feet away from moving

parts.

4. Shut of f the tool, remove the battery pack from

the tool, and wait for all movement to stop before

adjusting, servicing, cleaning, or storing the tool.

5. Check the tool for damaged parts—If there

are damaged guards or other parts, determine

whether it will operate properly . Check for

misaligned and binding moving parts, broken

parts, mounting, and any other condition that

may af fect its operation. Unless indicated in the

instructions, have an Authorized Service Dealer

repair or replace a damaged guard or part.

6. If the blade becomes worn, bent, or damaged,

replace it; contact an authorized T oro distributor .

4

7. Do not attempt to service or repair the tool,

battery pack, or battery charger except as

indicated in the instructions. Have an Authorized

Service Dealer perform service using identical

replacement parts to ensure that the product is

safely maintained.

8. Store an idle tool indoors in a place that is dry ,

secure, and out of the reach of children.

9. Do not dispose of the battery in a re. The

cell may explode. Check with local codes for

possible special disposal instructions.

SA VE THESE

INSTRUCTIONS

5

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area

of potential danger . Replace any decal that is damaged or missing.

decal144-3098

144-3098

decal144-3096

144-3096

decal144-3094

144-3094

1. The battery pack is

charging.

3. The battery pack is over

or under the appropriate

temperature range.

2. The battery pack is fully

charged.

4. Battery pack charging fault

decal140-8475

140-8475

1. Read the Operator ’ s

Manual .

3. Keep away from open re

or ames.

2. Call2Recycle® battery

recycling program

4. Do not expose to rain.

6

decal137-9461

137-9461

1. Battery charge status

decal139-5210

139-5210

1. W arning—read the Operator ’ s Manual ; stay away from

moving parts; keep all guards in place; wear eye protection;

do not operate in wet conditions.

decal139-5346

139-5346

7

Setup

Loose Parts

Use the chart below to verify that all parts have been shipped.

Procedure Description

Qty .

Use

1

Allen wrench 1

Unfold the handle.

Auxiliary handle assembly 12

Edger adjustment tool 1

Install the auxiliary handle.

Important: The battery pack is not fully charged when you purchase it. Before using the tool for the

rst time, refer to Charging the Battery Pack ( page 14 ) .

1

Unfolding the Handle

Parts needed for this procedure:

1 Allen wrench

Procedure

1. Unfold the handle (A of Figure 3 ).

2. Align the locking button on the lower shaft with the slotted hole on the upper shaft and slide the 2 shafts

together (B and C of Figure 3 ).

Note: The locking button clicks into the slotted hole when the shafts are secured (D of Figure 3 ).

3. Using the provided Allen wrench, tighten the screw on the shaft connector until it is secure (E of Figure 3 ).

8

g333338

Figure 3

9

2

Installing the Auxiliary Handle

Parts needed for this procedure:

1 Auxiliary handle assembly

1 Edger adjustment tool

Procedure

1. Separate the auxiliary handle from the handle plate by removing the 4 screws (A of Figure 4 ).

2. Line up the auxiliary handle with auxiliary handle plate on the edger handle (B of Figure 4 ).

3. Secure the auxiliary handle to the handle plate with the 4 screws previously removed (C of Figure 4 )

using the provided Allen wrench.

g333337

Figure 4

10

Product Overview

g429628

Figure 5

1. Battery latch

5. Guard

2. Lockout button 6. Air venting areas

3. Auxiliary handle 7. Blade

4. Run trigger

g330065

Figure 6

1. Battery charger Model

88610 (included with

Model 51833)

2. Battery pack Model 88620

(included with Model

51833)

Specications

Model 51833

Blade Length

203 mm (8 inches)

Rated V oltage

60V DC maximum, 54 VDC

nominal usage

No-load Speed

7000 rpm

W eight (without battery

pack)

4.7 kg (10.4 lbs)

Charger T ype

T oro 60V lithium-ion battery

chargers

Battery T ype T oro 60V lithium-ion battery

packs

Appropriate T emperature Ranges

Charge/store the battery pack

at

5°C (41°F) to 40°C (104°F)*

Use the battery pack at

-30°C (-22°F) to 49°C (120°F)*

Use the machine at

0°C (32°F) to 49°C (120°F)*

*Charging time will increase if you do not charge the

battery within this range.

Store the tool, battery pack, and battery charger in an

enclosed clean, dry area.

Attachments/Accessories

A selection of T oro approved attachments and

accessories is available for use with the machine

to enhance and expand its capabilities. Contact

your Authorized Service Dealer or authorized T oro

distributor or go to www .T oro.com for a list of all

approved attachments and accessories.

T o ensure optimum performance and continued safety

certication of the machine, use only genuine T oro

replacement parts and accessories. Replacement

parts and accessories made by other manufacturers

could be dangerous.

1 1

Operation

Starting the Edger

1. Align the cavity in the battery pack with the

tongue on the handle housing ( Figure 7 ).

2. Push the battery pack into the handle until the

battery locks into the latch ( Figure 7 ).

g333238

Figure 7

1. Battery latch

3. T o start the edger , pull back on the lockout

button, then squeeze the run trigger ( Figure 8 ).

Note: Once the edger is running you can

release the lockout button.

g333239

Figure 8

1. Lockout button 2. Run trigger

Shutting Off the Edger

T o shut of f the trimmer , release the trigger .

Whenever you are not using the edger or are

transporting the edger to or from the work area,

remove the battery pack.

Removing the Battery Pack

from the T rimmer

Press the battery latch on the machine to release the

battery pack and slide the battery pack out of the

machine ( Figure 9 ).

g333240

Figure 9

1. Battery latch

12

Adjusting the Depth of Cut

1. Remove the battery from the edger .

2. Loosen the wing nut on the wheel and move it

up or down in the track to increase or decrease

the depth ( Figure 10 ).

g333293

Figure 10

3. Adjust the depth so that the blade barely touches

the ground when the machine is held in a normal

working position.

4. T ighten the wing nut.

5. Standing in a normal working position, check the

depth of cut again and correct if necessary .

13

Charging the Battery Pack

Important: The battery pack is not fully charged

when you purchase it. Before using the tool for

the rst time, place the battery pack in the charger

and charge it until the LED display indicates the

battery pack is fully charged. Read all safety

precautions.

Important: Charge the battery pack only in

temperatures that are within the appropriate

range; refer to Specications ( page 1 1 ) .

Note: At any time, press the battery-charge-indicator

button on the battery pack to display the current

charge (LED indicators).

1. Ensure that the vents on the battery and charger

are clear of any dust and debris.

g330066

Figure 1 1

1. Battery pack cavity

5. LED indicators (current

charge)

2. Battery pack venting areas 6. Handle

3. Battery pack terminals

7. Charger

4. Battery-charge-indicator

button

2. Line up the charger with the cavity on the back

of the battery pack ( Figure 1 1 ).

3. Slide the charger into the battery pack until it is

fully seated ( Figure 1 1 ).

4. T o remove the charger , slide the charger

backward out of the battery .

5. Refer to the following table to interpret the LED

indicator light on the battery charger .

Indicator

light

Indicates

Of f

No battery pack inserted

Green

blinking

Battery pack is charging

Green

Battery pack is charged

Red

Battery pack and/or battery charger is over or under

the appropriate temperature range

Red

blinking

Battery pack charging fault*

*Refer to T roubleshooting ( page 18 ) for more

information.

Important: The battery can be left on the charger

for short periods between uses.

If the battery will not be used for longer periods,

remove the battery from the charger; refer to

Storage ( page 17 ) .

14

Operating T ips

•Hold the edger with your right hand on the rear

handle and your left hand on the front handle.

•Keep a rm grip with both hands while in operation.

•The edger should be held at a comfortable position

with the rear handle at about hip height.

•The edger will edge along sidewalks, driveways,

ower beds, curbs, and similar areas.

•Cut at a steady pace. If the blade begins to slow

down, you are edging too fast; slow your pace. Do

not force the blade into the ground.

•Light contact of the blade against the sidewalk

edge, curb, etc., is acceptable and will not damage

the edger .

•T o achieve the best appearance, edge when grass

is dry . Edging in wet soil or wet grass areas might

clog the blade guard and result in an uneven

edge. If the blade guard becomes clogged, stop

the edger , remove the battery and remove debris

from the blade guard.

g333294

Figure 12

1. Blade 2. Wheel

15

Maintenance

After each use of the edger , complete the following:

1. Remove the battery from the edger .

2. Wipe the edger clean with a damp cloth. Do not

hose the edger down or submerge it in water .

3. Wipe or scrape clean the cutting head area any

time there is an accumulation of debris.

4. Check and tighten all fasteners. If any part is

damaged or lost, repair or replace it.

5. Brush debris away from air intake vents and

exhaust on motor housing to prevent the motor

from overheating ( Figure 5 ).

Replacing the Blade

If the blade becomes worn, bent, or damaged, replace

it; contact your authorized T oro distributor .

1. Ensure that the battery is removed from the

machine.

2. Secure the blade so that it cannot spin by

inserting a screwdriver (not included) to the slot

in the edger head as shown in Figure 14 .

Note: Y ou may need to turn the blade to nd

the slot

3. Remove the blade nut by turning it clockwise

using the edger adjustment tool provided ( Figure

13 ).

g334038

Figure 13

1. Rotate clockwise to loosen

the blade nut

2. Rotate counterclockwise

to tighten the blade nut

4. Remove the blade washer and the old blade

(Figure 14 ).

Note: Y ou may discard the old blade.

5. Install the new blade and secure it with the

previously removed blade washer and blade nut.

g334037

Figure 14

1. Edger adjustment tool 4. Blade

2. Blade nut 5. Blade-secure slot

3. Blade washer

6. Screwdriver (not included)

6. T ighten the blade nut by turning it

counterclockwise with the wrench provided

(Figure 13 ).

Replacing the Wheel

1. Ensure that the battery is removed from the

machine.

2. Remove the wing nut, washer , bushings,

wheel, rubber washer , and wheel axle from the

depth-of-cut track on the edger ( Figure 15 ).

g334039

Figure 15

1. Depth-of-cut track

5. Bushings

2. Wheel axle 6. W asher

3. Wheel 7. Wing nut

4. Rubber washer

3. Replace any damaged or missing parts; contact

your authorized T oro distributor .

4. Insert the wheel axle through the track with the

tab facing down as shown in Figure 15 .

5. Install the rubber washer , bushings, wheel, small

washer , and wing nut to the axle ( Figure 15 ).

16

6. T ighten the wing nut to secure the wheel.

Replacing the Skid Plate

If the skid plate becomes worn or damaged, replace

it; contact your authorized T oro distributor .

1. Ensure that the battery is removed from the

machine.

2. Remove the 2 screws securing the skid plate to

the edger ( Figure 12 ).

g344651

Figure 16

1. Skid plate 2. Screws

3. Replace the skid plate and secure it using the 2

screws removed previously .

Storage

Important: Store the tool, battery pack, and

charger only in temperatures that are within the

appropriate range; refer to Specications ( page

1 1 ) .

Important: If you are storing the battery pack for

the off-season, remove the battery pack from the

tool and charge the battery pack until 2 or 3 LED

indicators turn green on the battery . Do not store

a fully charged or fully depleted battery . When you

are ready to use the tool again, charge the battery

pack until the left indicator light turns green on

the charger or all 4 LED indicators turn green on

the battery .

•Disconnect the product from the power supply

(i.e., remove the plug from the power supply or the

battery pack) and check for damage after use.

•Do not store the tool with the battery pack installed.

•Clean all foreign material from the product.

•When not in use, store the tool, battery pack, and

battery charger out of the reach of children.

•Keep the tool, battery pack, and battery charger

away from corrosive agents, such as garden

chemicals and de-icing salts.

•T o reduce the risk of serious personal injury , do

not store the battery pack outside or in vehicles.

•Store the tool, battery pack, and battery charger

in an enclosed clean, dry area.

Preparing the Battery Pack

for Recycling

Important: Upon removal, cover the terminals of

the battery pack with heavy-duty adhesive tape.

Do not attempt to destroy or disassemble the

battery pack or remove any of its components.

Lithium-ion battery packs labeled with the

Call2Recycle seal can be recycled at any

participating retailer or battery recycling

facility in the Call2Recycle program (US

and Canada only). T o locate a participating

retailer or facility closest to you, please call

1-800-822-8837 or visit www .call2recycle.org.

If you cannot locate a participating retailer or

facility nearby , or if your rechargeable battery

is not labeled with the Call2Recycle seal,

please contact your local municipality for more

information on how to responsibly recycle the

battery . If you are located outside of the US

and Canada, please contact your authorized

T oro distributor .

17

T roubleshooting

Perform only the steps described in these instructions. All further inspection, maintenance, and repair work

must be performed by an authorized service center or a similarly qualied specialist if you cannot solve the

problem yourself.

Always remove the battery from the tool when troubleshooting, inspecting, maintaining, or cleaning the tool.

Problem

Possible Cause Corrective Action

1. The battery is not fully installed in the

tool.

1. Remove and then replace the battery

into the tool, making sure that it is fully

installed and latched.

2. The battery pack is not charged.

2. Remove the battery pack from the tool

and charge it.

3. The battery pack is damaged. 3. Replace the battery pack.

The tool does not start.

4. There is another electrical problem

with the tool.

4. Contact an Authorized Service Dealer .

1. The battery pack charge capacity is

too low .

1. Remove the battery pack from the tool

and fully charge the battery pack.

The tool does not reach full power .

2. The air vents are blocked.

2. Clean the air vents.

1. There is debris on the cutting head of

the edger .

1. Clean any debris of f from the cutting

head area.

The tool is producing excessive vibration

or noise.

2. The blade is not properly tightened. 2. T ighten the blade.

1. The depth is set too low .

1. Raise the depth of cut.The edger stops during use.

2. W alking or cutting too fast. 2. Slow your pace so the machine can

work ef fectively .

The battery pack loses charge quickly . 1. The battery pack is over or under the

appropriate temperature range.

1. Move the battery pack to a place

where it is dry and the temperature is

between 5°C (41°F) and 40°C (104°F).

1. The battery charger is over or under

the appropriate temperature range.

1. Unplug the battery charger and move

it to a place where it is dry and the

temperature is between 5°C (41°F)

and 40°C (104°F).

The battery charger is not working.

2. The outlet that the battery charger is

plugged into does not have power .

2. Contact your licensed electrician to

repair the outlet.

The LED indicator light on the battery

charger is red.

1. The battery charger and/or battery

pack is over or under the appropriate

temperature range.

1. Unplug the battery charger and move

the battery charger and battery pack

to a place where it is dry and the

temperature is between 5°C (41°F)

and 40°C (104°F).

1. There is an error in the communication

between the battery pack and the

charger .

1. Remove the battery pack from the

battery charger , unplug the battery

charger from the outlet, and wait 10

seconds. Plug the battery charger into

the outlet again and place the battery

pack on the battery charger . If the LED

indicator light on the battery charger is

still blinking red, repeat this procedure

again. If the LED indicator light on

the battery charger is still blinking red

after 2 attempts, properly dispose of

the battery pack at a battery recycling

facility .

The LED indicator light on the battery

charger is blinking red.

2. The battery pack is weak.

2. Properly dispose of the battery pack at

a battery recycling facility .

18

La page charge ...

Toro Flex-Force Power System 60V Stick Edger Manuel utilisateur

Toro Flex-Force Power System 60V Stick Edger Manuel utilisateur

dans d''autres langues