Samsung DV40J3000GW/A2 Manuel utilisateur

Gas and Electric Dryer

user manual

Imagine the possibilities

Thank you for purchasing this Samsung product.

DV40J3000E(G)*

This manual is made with 100% recycled paper.

English - 2

contents

INSTALLING YOUR DRYER

7

7 Unpacking your dryer

7 Basic requirments

8 Ducting requirements

9 Important to installer

9 Location considerations

9 Alcove or closet installation

10 Exhausting

11 Gas requirements

11 Commonwealth of Massachusetts

installation instructions

12 Electrical requirements

12 Grounding

13 Electrical connections

14 Installation - General procedure

17 Final installation check list

18 Dryer Exhaust Tips

19 Door Reversal

OPERATING INSTRUCTIONS, TIPS

21

21 Overview of the control panel

23 Child lock

24 Clean the lint ﬁlter

24 Load the dryer properly

24 Getting started

CARE AND CLEANING

25

25 Control Panel

25 Tumbler

25 Powder Coated Tumbler

25 Dryer Exterior

25 Dryer Exhaust System

SPECIAL LAUNDRY TIPS

26

26 Special laundry tips

TROUBLESHOOTING

27

27 Check these points if your dryer…

28 Information codes

APPENDIX

29

29 Fabric care chart

30 Protecting the environment

30 Declaration of conformity

30 Speciﬁcations

31 Cycle chart

English - 3

safety instructions

Congratulations on your new Samsung Dryer. This manual contains valuable

information on the installation, use, and care of your appliance. Please take the

time to read this manual to take full advantage of your dryer’s many beneﬁts and

features.

WHAT YOU NEED TO KNOW ABOUT SAFETY INSTRUCTIONS

Warnings and Important Safety Instructions in this manual do not cover all possible conditions and

situations that may occur. It is your responsibility to use common sense, caution, and care when installing,

maintaining, or operating your dryer.

Always contact your manufacturer about problems or conditions you do not understand.

IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS

What the icons and signs in this user manual mean:

WARNING

Hazards or unsafe practices that may result in severe personal injury

or death.

Follow the information in this manual to minimize the risk of ﬁre or

explosion or to prevent property damage, personal injury, or death.

Do not store or use gasoline or other ﬂammable vapors and liquids near

this or any other appliance.

CAUTION

Hazards or unsafe practices that may result in minor personal injury or

property damage.

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions explicitly.

Unplug the power plug from the wall socket.

Make sure the machine is grounded to prevent electric shock.

Call the service center for help.

Note

These warning icons are here to prevent injury to you and others.

Please follow them explicitly.

After reading this section, keep it in a safe place for future reference.

Read all instructions before using the appliance.

English - 4

WARNING: To reduce the risk of ﬁre, electric shock, or injury to persons when using your

appliance, follow basic precautions, including the following:

1. Read all instructions before using this appliance.

2. Do not dry articles that have been previously cleaned in, washed in, soaked in,

or spotted with gasoline, dry-cleaning solvents, or other ﬂammable or explosive

substances, as they give o vapors that could ignite or explode.

3. Do not use the dryer to dry clothes which have traces of any ﬂammable substance,

such as vegetable oil, cooking oil, machine oil, ﬂammable chemicals, thinner, etc., or

anything containing wax or chemicals, such as mops and cleaning cloths. Flammable

substances may cause the fabric to catch ﬁre by itself.

4. Do not store or use gasoline or other ﬂammable vapors and liquids near this or any

other appliance.

5. Do not allow children to play on or in the appliance. Close supervision of children is

necessary when the appliance is used near children.

6. Before the appliance is removed from service or discarded, remove the door to the

drying compartment.

7. Do not reach into the appliance if the drum is moving.

8. Do not install or store this appliance where it will be exposed to the weather.

9. Do not tamper with internal controls.

10. Do not repair or replace any part of the appliance or attempt any service unless

speciﬁcally recommended in the user-maintenance instructions or in published user-

repair instructions that you understand and have the skills to carry out.

11. Do not use fabric softeners or products to eliminate static unless recommended by the

manufacturer of the fabric softener or product.

12. Clean the lint screen before or after each load.

13. Do not use heat to dry articles containing foam rubber or similarly textured rubber-like

materials.

14. Keep area around the exhaust opening and adjacent surrounding areas free from the

accumulation of lint, dust, and dirt.

15. The interior of the appliance and exhaust duct should be cleaned periodically by

qualiﬁed service personnel.

16. Do not place items exposed to cooking oils in your dryer. Items contaminated with

cooking oils may contribute to a chemical reaction that could cause a load to catch ﬁre.

17. This appliance must be grounded. See “Electrical requirements” and ”Grounding” in

installing your dryer section.

18. Do not allow children to play on or in the appliance. Close supervision of children is

necessary when the appliance is used near children.

19. Do not insert your hand under the dryer.

- This may result in injury.

20. Take care that children’s ﬁngers are not caught in the door when closing it.

- This may result in injury.

21. Control board and inlet valve are intentionally not grounded and may present a risk of

electric shock only during servicing. Service personnel — Do not contact this part while

appliance is energize.

safety instructions

WARNING

English - 5

• Clothesdryerinstallationmustbeperformedbyaqualiedinstaller.

• Installtheclothesdryeraccordingtothemanufacturer’sinstructionsandlocalcodes.

• Donotinstallaclothesdryerwithexibleplasticventingmaterials.Ifexiblemetal

(foil type) duct is installed, it must be of a speciﬁc type identiﬁed by the appliance

manufacturer as suitable for use with clothes dryers. Flexible venting materials are

known to collapse, be easily crushed, and trap lint. These conditions will obstruct

clothes dryer airﬂow and increase the risk of ﬁre.

• Toreducetheriskofsevereinjuryordeath,followallinstallationinstructions.

WARNING - Risk of Fire

To reduce the risk of ﬁre or explosion:

• Do not dry items that have been previously cleaned, washed, soaked, or spotted with

gasoline, dry cleaning solvents, or other ﬂammable or explosive substances. They

emit vapors that could ignite or explode. Any material that has been in contact with a

cleaning solvent or ﬂammable liquids or solids should not be placed in the dryer until all

traces of these ﬂammable liquids or solids and their fumes have been removed.

There are many highly ﬂammable items used in homes, such as acetone, denatured

alcohol, gasoline, kerosene, some liquid household cleaners, some spot removers,

turpentine, waxes, and wax removers.

• Items containing foam rubber (may be labeled latex foam) or similarly textured rubber-

like materials must not be dried on a heat setting. Heated foam rubber materials can,

under certain circumstances, produce ﬁre by spontaneous combustion.

What to do if you smell gas:

• Donottrytolightanyappliance.

• Donotturnontheappliance.

• Donottouchanyelectricalswitch.

• Donotuseanyphoneinyourbuilding.

• Cleartheroom,buildingorareaofalloccupants.

• Immediatelycallyourgassupplierfromaneighbor’sphone.Followthegassupplier’s

instructions.

• Ifyoucannotreachyourgassupplier,calltheredepartment.

• Installationandservicemustbeperformedbyaqualiedinstaller,serviceagency,orthe

gas supplier.

Gas Appliances:

WARNING: This product contains chemicals known to the State of California to cause

cancer and reproductive toxicity.

Gas appliances can cause low-level exposure to Proposition 65 listed substances,

including but not limited to , benzene, carbon monoxide, formaldehyde and soot,

substances resulting from the incomplete combustion of natural gas or LP fuels.

WARNING

English - 6

Do not allow children or pets to play on, in, or in front of the appliance. Close supervision is

necessary when the appliance is used near children and pets.

Before discarding or removing your dryer from service, remove the door to the drying

compartment to prevent children or animals from becoming trapped inside.

Do not reach into the appliance when the drum is moving.

Do not install or store this appliance where it will be exposed to the weather.

Do not tamper with controls.

Do not repair, replace, or attempt to service any part of the appliance unless speciﬁcally

instructed to in the user-repair instructions and you have the understanding and skills to

carry out the procedure.

Do not use fabric softeners or products to eliminate static unless the softener or product is

recommended for dryer use by the manufacturer of the fabric softener or product.

Clean the lint screen before or after each load.

Keep the area around the exhaust opening and surrounding areas free from lint, dust, and dirt.

The interior of the dryer and exhaust duct should be cleaned periodically by qualiﬁed service

personnel.

This appliance must be properly grounded. Never plug the power cord into a receptacle

that is not grounded adequately or not in accordance with local and national codes. See

installation instructions for information about grounding this appliance.

Do not sit on top of the dryer.

Ensure pockets are free from small, irregularly shaped hard objects, foreign material, etc. ie.

coins, knives, pins, etc. These objects could damage your dryer.

Do not wash clothing with large buckles, buttons, or other heavy metal or solid objects.

Gas leaks may occur in your system, resulting in a dangerous situation.

Gas leaks may not be detected by smell alone.

Gas suppliers recommend you purchase and install a UL-approved gas detector.

Install and use in accordance with the manufacturer’s instructions.

Do not place items in your dryer that have been spotted or soaked with vegetable oil or cooking

oil. Even after being washed, these items may contain signiﬁcant amounts of these oils.

Residual oil on clothing can ignite spontaneoulsy. The potential for spontaneous

combustion increases when items containing vegetable oil or cooking oil are exposed to

heat. Heat sources such as your dryer can warm these items, allowing an oxidation reaction

in the oil to occur. Oxidation creates heat. If this heat cannot escape, the items can become

hot enough to catch ﬁre. Piling, stacking, or storing these kinds of items may prevent heat

from escaping and can create a ﬁre hazard.

All washed and unwashed fabrics that contain vegetable oil or cooking oil can be

dangerous. Washing these items in hot water with extra detergent will reduce, but not

eliminate, the hazard. Always use the Cool Down cycle for these items to reduce their

temperature. Never remove these items from the dryer hot or interrupt the drying cycle until

the items have run through the Cool Down cycle. Never pile or stack these items when they

are hot.

safety instructions

WARNING

English - 7

installing your dryer

UNPACKING YOUR DRYER

Unpack your dryer and inspect it for shipping damage. Make sure you have received all of the items

shown below. If your dryer was damaged during shipping, or you do not have all of the items, contact

1-800-SAMSUNG (726-7864).

To prevent personal injury or strain, wear protective gloves whenever lifting or carrying the dryer.

Packing materials can be dangerous to children. Keep all packing material (plastic bags, polystyrene,

etc.) well out of children’s reach.

Do not move the product while holding the front part of the top cover of the dryer.

- This may cause the cover to be separated and result in injury.

Tools needed

Pliers Cutting knife Pipe wrench (gas only) Nut drivers

Level Phillips Screwdriver Duct tape Wrench

BASIC REQUIRMENTS

Make sure you have everything necessary for proper installation

• A GROUNDED ELECTRICAL OUTLET is required. See Electrical Requirements.

• A POWER CORD for electric dryers (except in Canada).

• GAS LINES (if installing a gas dryer). The gas lines must meet national and local codes.

• EXHAUST SYSTEM - must be rigid metal or ﬂexible sti-walled metal exhaust ducting.

WARNING

CAUTION

Top Cover

Control panel

Door

Frame Front

Filter

Duct Exhaust

[ BACK ]

01 installing your dryer

English - 8

installing your dryer

DUCTING REQUIREMENTS

• Use a 4-inch (10.2 cm) diameter rigid aluminum or rigid galvanized steel duct.

• Do not use a smaller duct.

• Ducts larger than 4 inches (10.2 cm) in diameter can cause increased lint accumulation.

Lint accumulation should be cleaned regularly.

• If a ﬂexible metal duct must be used, use the type with a sti sheet metal wall. Do not use a ﬂexible duct

with a thin foil wall. Serious blockage can result if the ﬂexible metal duct is bent too sharply.

• Never install any type of ﬂexible duct in walls, ceilings, or other concealed spaces.

• Keep the exhaust duct as straight and short as possible.

• Secure joints with duct tape. Do not use screws.

• Plastic ﬂexible duct can kink, sag, be punctured, reduce airﬂow, extend drying times, and aect dryer

operation.

• Exhaust systems longer than recommended can extend drying times, aect machine operation, and

may collect lint.

• The exhaust duct should end with an exhaust hood with a swing-out damper to prevent back drafts and

the entry of wildlife. Never use an exhaust hood with a magnetic damper.

• The hood should have at least 12 inches (30.5 cm) of clearance between the bottom of the hood and

the ground or other obstruction. The hood opening should point down.

• Never install a screen over the exhaust outlet.

• To avoid lint buildup, do not exhaust the dryer directly into a window well. Do not exhaust under a house

or porch.

• If exhaust ductwork must run through an unheated area, the duct should be insulated and slope slightly

down towards the exhaust hood to reduce condensation and lint buildup.

• Inspect and clean the interior of the exhaust system at least once a year. Unplug the power cord before

cleaning.

• Check frequently to be sure the exhaust hood damper opens and closes freely.

• Check once per month, and clean at least one time per year. Note: If clothes are not getting dry, then

check ducting for obstructions.

• Do not exhaust dryer into any wall, ceiling, crawl space, or concealed space of a building, gas vent, or

any other common duct or chimney. This could create a ﬁre hazard from lint expelled by the dryer.

ELECTRIC AND GAS DRYER

Weather Hood Type

Recommended Use only for short-run installation

4” (10.2 cm) 2.5” (6.4 cm)

No. of 90° elbows Rigid Metallic Flexible* Rigid Metallic Flexible*

0 80 ft. (24.4 m) 41 ft. (12.4 m) 74 ft. (22.6 m) 33 ft. (10.1 m)

1 68 ft. (20.7 m) 37 ft. (11.2 m) 62 ft. (18.9 m) 29 ft. (8.8 m)

2 57 ft. (17.4 m) 33 ft. (10.1 m) 51 ft. (15.5 m) 25 ft. (7.6 m)

3 47 ft. (14.3 m) 29 ft. (8.8 m) 41 ft. (12.5 m) 21 ft. (6.5 m)

* Do not use non-metallic ﬂexible duct.

English - 9

If the new dryer is being installed into an existing exhaust system, you must

make sure:

• The exhaust system meets all local, state, and national codes.

• That a ﬂexible plastic duct is not used.

• To Inspect and clean all lint buildup from inside the existing duct.

• The duct is not kinked or crushed.

• The exhaust hood damper opens and closes freely.

The static pressure in any exhaust system must not exceed 0.83 inches of water column, or be

less than 0.

This can be measured with the dryer running with a manometer at the point where the exhaust

duct connects to the dryer. A no-heat setting should be used. The dryer tumbler should be

empty and the lint ﬁlter clean.

IMPORTANT TO INSTALLER

Please read the following instructions carefully before installing the dryer. These instructions should be kept

for future reference.

Remove the door from all discarded appliances to avoid the danger of a child suocating.

LOCATION CONSIDERATIONS

Locate the dryer where there is enough space at the front for loading the dryer, and enough space behind

for the exhaust system. This dryer is factory-ready for rear exhaust. To exhaust out the bottom or the right

or the left (electric model only), use the accessory exhaust kit (sold separately). Instructions are included

with the kit. It’s important to make sure the room has enough fresh air. The dryer must be located where

there is no air-ﬂow obstruction.

On gas dryers, adequate clearance as noted on the data plate must be maintained to ensure adequate air

for combustion and proper dryer operation.

Do not install or store the dryer in an area where it will be exposed to water and/or weather. Keep the dryer

area clear of combustible materials, casoline, and other ﬂammable vapors and liquids. A dryer produces

combustible lint. The area around the dryer should be kept lint free.

ALCOVE OR CLOSET INSTALLATION

You must exhaust the dryer to the outside to reduce the risk of ﬁre when you install the dryer in alcove

or closet.

• No other fuel-burning appliance should be installed in the same closet as the dryer.

• WARNING: To reduce the risk of ﬁre, you must exhaust the dryer to the outdoors.

See Exhaust information section.

• Minimum clearances between the dryer and adjacent walls or other surfaces are:

2” in front, 17” on top, 1” on either side, and 5” in the back.

• The closet front must have two unobstructed air openings for a combined minimum total area of 72 in²

with 3” minimum clearance on the top and bottom. A louvered door with equivalent space clearance is

acceptable.

01 installing your dryer

WARNING

English - 10

installing your dryer

EXHAUSTING

The dryer shall not be exhausted into a chimney, a wall, a ceiling, an attic, a crawl space, or a concealed

space of a building.

Exhausting the dryer to the outside will prevent large amount of lint and moisture from being blown into the

room.

In the United States:

• All dryers must be exhausted to the outside.

• The required exhaust duct is 4 inches (10.2 cm) in diameter.

• Use only those foil-type ﬂexible ducts, if any, speciﬁcally identiﬁed for use with the appliance

by the manufacturer and that comply with the Outline for Clothes Dryer Transition Duct,

Subject 2158A shall be used.

• See “Ducting Requirements” in installing your dryer section for the maximum duct length and

number of bends shall be used.

• The total length of ﬂexible metal duct shall not exceed 2.4 m.

• Do not assemble the duct with screws or other fastening means that extend into the duct

and catch lint.

In Canada:

• All dryer must be exhausted to the outside.

• The exhaust duct should be 4 inches(10.2 cm ) in diameter.

• Use only those foil-type ﬂexible ducts, if any, speciﬁcally indentiﬁed for use with the appliance

by the manufacturer shall be used.

• See “Ducting Requirements” in installing your dryer section for the maximum duct length and

number of bends.

• The total length of ﬂexible metal duct shall not exceed 2.4 m.

• Do not assemble the duct with screws or other fastening means that extend into the duct

and catch lint

Outside the U.S. and Canada:

• Refer to the local codes.

You must exhaust the dryer to the outside to reduce the risk of ﬁre when you install the

dryer in an alcove or closet.

NEVER USE A PLASTIC OR NON-METAL FLEXIBLE DUCT.

If your existing ductwork is plastic, non-metal, or combustible, replace it with metal.

Use only a metal exhaust duct that is non-ﬂammable to ensure containment of exhaust air,

heat, and lint.

WARNING

English - 11

GAS REQUIREMENTS

Use only natural or LP (liquid propane) gases.

THE INSTALLATION MUST CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL

CODES, WITH THE NATIONAL FUEL GAS CODE ANSI/Z223.1, LATEST REVISION (FOR THE UNITED

STATES), OR WITH THE CAN/CGA-B149 INSTALLATION CODES (FOR CANADA).

Gas dryers are equipped with a burner vent for use with natural gas. If you plan to use your dryer with LP

(liquid propane) gas, it must be converted for safe and proper performance by a qualiﬁed service technician.

A 1/2” (1.27 cm) gas supply line is recommended and must be reduced to connect to the 3/8” (1 cm) gas

line on your dryer. The National Fuel Gas Code requires that an accessible, approved manual gas shut-o

valve be installed within 6” of your dryer.

Gas dryers installed in residential garages must be raised 18 inches (46 cm) above the ﬂoor.

Additionally, a 1/8” (0.3 cm) N.P.T. (National Pipe Thread) plugged tapping, accessible for test gauge

connection, must be installed immediately upstream of your dryer’s gas supply connection.

Your dryer must be disconnected from the gas supply pipe system during any pressure testing of the

system.

DO NOT reuse old ﬂexible metal gas lines. Flexible gas lines must be design certiﬁed by the American Gas

Association (CGA in Canada).

• Any pipe joint compound used must be resistant to the action of any liqueﬁed petroleum gas.

• As a courtesy, most local gas utilities will inspect a gas appliance installation.

GAS IGNITION – Your dryer uses an automatic ignition system to ignite the burner.

There is no constant burning pilot.

COMMONWEALTH OF MASSACHUSETTS INSTALLATION

INSTRUCTIONS

Your dryer must be installed by a licensed plumber or gas ﬁtter. A “T” handle manual gas valve must be

installed in the gas supply line to your dryer. If a ﬂexible gas connector is used to install your dryer, the

connector can be no longer than 3’ (36”).

• Gas leaks may occur in your system, creating a dangerous situation.

• Gas leaks may not be detected by smell alone.

• Gas suppliers recommend you purchase and install a UL-approved gas detector.

• Install and use in accordance with the manufacturer’s instructions.

01 installing your dryer

WARNING

English - 12

installing your dryer

ELECTRICAL REQUIREMENTS

The Wiring diagram is located on the plate below the control panel or frame back.

• Improperly connecting the equipment grounding conductor can result in a risk of electric shock.

Check with a qualiﬁed electrician or serviceman if you are in doubt as to whether your dryer is

properly grounded. Do not modify the plug provided with your dryer – if it doesn’t ﬁt the outlet,

have a proper outlet installed by a qualiﬁed electrician.

• To prevent unnecessary risk of ﬁre, electrical shock, or personal injury, all wiring and grounding

must be done in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA No. 70-Latest Revision (for the U.S.) or the Canadian Electrical Code

CSA C22.1 – Latest Revisions and local codes and ordinances. It is your responsibility to provide

adequate electrical services for your dryer.

• All gas installations must be done in accordance with the national Fuel Code ANSI/Z2231 – Latest

Revision (for the U.S.) or CAN/CGA – B149 Installation Codes – Latest Revision (for Canada) and

local codes and ordinances.

GROUNDING

This dryer must be grounded. In the event of malfunction or breakdown, the ground will reduce the risk of

electrical shock by providing a path of least resistance for the electrical current.

Gas models

Your dryer has a cord with an equipment-grounding conductor and a grounding plug.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

Do not modify the plug provided with your dryer – if it doesn’t ﬁt the outlet, have a proper outlet

installed by a qualiﬁed electrician.

Never connect the ground wire to plastic plumbing lines, gas lines, or hot water pipes.

Electric models

Your dryer has an optional cord with an equipment-grounding conductor and a grounding plug,

This cord is sold separately.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

Do not modify the plug provided with your dryer – if it doesn’t ﬁt the outlet, have a proper outlet

installed by a qualiﬁed electrician.

If a power cord is not used and the electric dryer is to be permanently wired, the dryer must

be connected to a permanently grounded metal wiring system, or an equipment grounding

conductor must be run with the circuit conductors and connected to the equipment grounding

terminal or lead on the dryer.

WARNING

English - 13

ELECTRICAL CONNECTIONS

Before operating or testing, follow all grounding instructions in the Grounding section.

An individual branch (or separate) circuit serving only your dryer is recommended. DO NOT USE AN

EXTENSION CORD.

Gas models – U.S. and Canada

A 120 volt, 60 Hz AC approved electrical service, with a 15-ampere fuse or circuit breaker is

required.

Electric models – U.S. Only

Most U.S. dryers require a 120 / 240 volt, 60 Hz AC approved electrical service. Some require

120 / 208 volt, 60 Hz approved electrical service. The electric service requirements can be found

on the data label located behind the door. A 30-ampere fuse or circuit breaker on both sides of

the line is required.

• If a power cord is used, the cord should be plugged into a 30-ampere receptacle.

• The power cord is NOT provided with U.S. electric model dryers.

Risk of Electric Shock

When local codes allow, the dryer electrical supply may be connected by means of a new power

supply cord kit, marked for use with a dryer, that is U.L. listed and rated at a minimum of120/240

volts, 30-ampere with three No. 10 copper wire conductors terminated with closed loop

terminals, open-end spade lugs with turned up ends, or with tinned leads.

• Do not reuse a power supply cord from an old dryer. The power cord electric supply wiring

must be supported at the dryer cabinet by a suitable UL-listed strain relief.

• Grounding through the neutral conductor is prohibited for (1) new branch-circuit installations,

(2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit

grounding through the neutral conductor. (Use a 4-prong plug for a 4 wire receptacle, NEMA

type 14-30R.)

Electric models – Canada Only

• A 120 / 240 volt, 60 Hz AC approved electrical service fused through a 30-ampere fuse or

circuit breaker on both sides of the line is required.

• All Canadian models are shipped with the power cord attached. The power cord should be

plugged into a 30-ampere receptacle.

It is not permissible to convert a dryer in Canada to 208 volts.

01 installing your dryer

WARNING

English - 14

INSTALLATION - GENERAL PROCEDURE

For proper installation, we recommend that you hire a qualiﬁed installer.

Read these instructions completely before you begin the installation.

To install the dryer, follow these steps:

1. Move your dryer to an appropriate location for installation. Consider installing the dryer and washer side-

by-side so you have easy access to both appliances.

To move the dryer easily, lay two of the carton cushion-tops on the ﬂoor. Tip your dryer on its side so it

lies across both cushion-tops. Push the dryer so that it is near its ﬁnal location. Set your dryer upright.

Leave enough room around the dryer so you can attach the duct work, power cord, etc.

2. If you need to change the direction of the door, go to Door Reversal on page 19. When done, return to

Step 3 below.

3. Review the Exhausting section before installing the exhaust system. Install the duct work from your

dryer to the exhaust hood. The crimped end of the duct sections must point away from your dryer. DO

NOT use sheet metal screws when assembling ducting. These joints should be taped. Never use plastic

ﬂexible exhaust material.

A tip for tight installations: Attach a section of the exhaust system to your dryer before putting it in

place. Use duct tape to secure this section to your dryer, but do not cover the ventilation slots at the

back of the dryer cabinet.

4. If you have an electric model, skip to Step 6. If you have a gas model, go to the next step.

5. Review the Gas Requirements section, then follow the lettered steps below.

a. Remove the pipe thread protective cap.

b. Apply pipe joint compound or about 1 1/2 wraps of Teﬂon tape over all threaded connections.

The pipe joint compound must be resistant to the action of any liqueﬁed petroleum gas.

c. Connect the gas supply to your dryer. An additional ﬁtting is required to connect the 3/4” (1.9 cm)

female thread end of a ﬂexible connector to the 3/8” (1 cm) male threaded end on the dryer.

d. Securely tighten the gas line ﬁtting over the threads.

e. Turn on the gas supply. Check all gas connections for leaks using a soap solution. If bubbles

appear, tighten the connections and recheck. DO NOT use an open ﬂame to check for gas leaks.

f. Go to Step 6 on the next page

installing your dryer

English - 15

6. Review the Electrical Requirements section, then follow the 3 Wire system connection instructions (Step

7) or 4 Wire system instructions (Step 8) below.

7. Three Wire system instructions:

A. External ground connector

B. Neutral grounding wire (white)

C. Center silver-colored terminal block screw

D. Neutral wire (white or center wire)

E. ¾” (1.9 cm) UL-listed strain relief

1. Loosen or remove the center terminal block screw.

2. Connect the neutral wire (white or center wire) of the power

cord to the center, silver-colored terminal screw of the

terminal block. Tighten screw.

3. Connect the other wires to outer terminal block screws. Tighten screws.

4. Tighten the strain relief screws.

5. Insert the tab of the terminal block cover into your Dryer’s rear panel slot.

Secure the cover with a hold-down screw.

If converting from a 4-wire electrical system to a 3-wire, you must connect the ground strap

to the terminal block support to ground the dryer frame to the neutral conductor.

We recommend using Ring terminals. If you use Strap terminals, please ensure you install

them perfectly.

8. Four Wire System instructions:

A. External ground connector

B. Green or bare copper wire of power cord

C. ¾” (1.9 cm) UL-listed strain relief

D. Center silver-colored terminal block screw

E. Neutral Grounding wire (white)

F. Neutral wire (white or center wire)

1. Remove the External ground connector screw.

2. Connect the ground wire (green or unwrapped) of the

power cord to the external ground connector screw. If you

want to connect B (Green or bare copper wire of power

cord) to the Neutral Post without connecting it to A (cabinet

ground), call a service technician.

3. Loosen or remove the center terminal block screw.

4. Connect the neutral wire (white or center wire) of the power cord and the appliance ground

wire (white or green/yellow stripes) under the central screw of the terminal block.

5. Connect the other wires to the outer terminal block screws. Tighten screws.

6. Tighten the strain relief screws.

7. Insert the tab of the terminal block cover into your Dryer’s rear panel slot.

Secure the cover with a hold-down screw.

We recommend using Ring terminals. If you use Strap terminals, please ensure you install

them perfectly.

01 installing your dryer

WARNING

English - 16

installing your dryer

U.S. MODELS:

Risk Of Electric Shock

All U.S.models are designed for a 3-WIRE SYSTEM CONNECTION. The dryer frame is grounded to

the neutral conductor at the terminal block. A 4-WIRE SYSTEM CONNECTION is required for new or

remodeled construction, mobile homes, or if local codes do not permit grounding through neutral. If

you use the 4-wire system, you cannot ground the dryer frame to the neutral conductor at the terminal

block.

Remove the terminal block cover plate. Insert the power cord with a UL-listed strain relief through the

hole provided in the cabinet near the terminal block.

A strain relief must be used. Do not loosen the nuts already installed on the terminal block. Be sure

they are tight. Use a 3/8” (1cm) deep well socket.

9. To ensure that the dryer provides optimal drying performance, it must

be level. To level the dryer, follow the lettered steps below:

a. Using a level, check if the dryer is level side to side and then front

to back.

b. If the dryer is not level, adjust the leveling feet on the bottom of

the dryer until the dryer is level side to side and back to front.

Turning the feet clockwise retracts the feet. Turning the feet

clockwise loosens and extends them.

If you have a dryer and washer

To set the dryer to the same height as the washer, fully

retract the leveling feet by turning them counterclockwise,

then loosen the feet by turning them clockwise. Once

the dryer is the same height as the washer, follow the

directions above to level the dryer.

Adjust the leveling feet only as much as necessary to level the dryer. Extending the leveling

feet more than necessary can cause the dryer to vibrate.

10. Make sure all gas connections (on gas models) and exhaust, and electrical connections are complete.

Plug in your dryer, and then check its operation by using the checklist on the next page.

11. For GAS MODELS ONLY

The burner may not ignite initially due to air in the gas line. Allowing your dryer to operate on a heat

setting will purge the line. If the gas does not ignite within 5 minutes, turn your dryer o and wait 5

minutes. Be sure the gas supply to your dryer has been turned on. To conﬁrm gas ignition, check the

exhaust for heat.

Level

Leveling feet

Retract fully Then loosen

WARNING

English - 17

FINAL INSTALLATION CHECK LIST

 The dryer is plugged into an electrical outlet and grounded properly.

 The exhaust ductwork is hooked up and the joints are taped.

 You have used rigid or sti-walled ﬂexible metal duct material, not plastic ﬂexible duct.

 The dryer is level and is sitting ﬁrmly on the ﬂoor.

 For gas models: The gas is turned on and there are no gas leaks.

 Start your dryer to conﬁrm that it runs, heats, and shuts o.

01 installing your dryer

English - 18

installing your dryer

DRYER EXHAUST TIPS

Plastic or non-metal ﬂexible duct presents a potential ﬁre hazard.

1. Make sure your dryer is installed properly so it exhausts air

easily.

2. Use 4” diameter rigid metal duct. Tape all joints, including at

the dryer.

Never use lint-trapping screws.

3. Keep ducts as straight as possible.

4. Clean all old ducts before installing your new dryer.

Be sure the vent ﬂap opens and closes freely.

Inspect and clean the exhaust system annually.

Don’t let a poor exhaust system slow drying by:

1. Restricting your dryer with a poor exhaust system.

2. Using a plastic, thin foil, or non-metal ﬂexible duct.

3. Using unnecessarily long ducts that have many

elbows.

4. Using crushed or clogged venting or ducts.

WARNING

1 2

3 4

DUCT

TAPE

Wall

DUCT

EXHAUST

Dryer

English - 19

DOOR REVERSAL

If you want to reverse the direction of the door, it is recommended calling a

qualiﬁed service technician.

1. Unplug the power cord.

2. Remove the four hinge screws from the door

3. Remove the door by lifting it

4. Remove the two screws from the holder-lever, and then remove

the cover-holder.

5. Assemble the holder-lever on the opposite side using the screws

that were removed from the holder-lever-in Step 4.

6. Assemble the cover-holder on the opposite side.

7. Remove the two cover-hinges.

8. Assemble the two cover-hinges

on the opposite side.

Use a ﬂat head screwdriver(-)

to remove the cover-holder’s

cover-hinge.

9. Remove the 14 screws.

Two screw (L) are longer than the other screws.

01 installing your dryer

L

English - 20

installing your dryer

10. Remove the holder-glass.

11. Exchange the positions of:

: The cover-hinge and handle door

: The holder-hinge and guider-

holder glass

12. Remove the Lever-Door, and then

install it on the opposite side.

Refer to the illustrations on the

right to aid you in the assembly

process.

13. Remove the cover-hole (P).

14. Assemble the holder glass and then fasten the 14 screws

that you removed in step 9.

15. Attach the cover-hole.

16. Install the door on the frame-front and then fasten the 4screws that you removed in step 2.

Check the positions of the screws you installed in the hinge

door.

L

P

La page charge ...

Samsung DV40J3000GW/A2 Manuel utilisateur

Samsung DV40J3000GW/A2 Manuel utilisateur

dans d''autres langues

Documents connexes