City Theatrical Legacy 7030 QolorStrip Wireless LED Strips Manuel utilisateur
- Catégorie
- Stroboscopes
- Taper
- Manuel utilisateur
QolorStrip™
Wireless LED Strips
User’s Manual
© 2019 City Theatrical, Inc.
QolorStrip battery powered LED uplighter is covered by U.S. Patent # 7,432,803
and other patents pending.
Page 2 of 22
Contents
Disclaimer ...................................................................................................................................................... 2
Product Modification ....................................................................................................................................... 3
Radio Compliance Information ....................................................................................................................... 3
5792M SHoW DMX Neo Radio CE Declaration of Conformity .................................................................................... 4
System Compliance Information .................................................................................................................... 6
Safety Notices ................................................................................................................................................ 6
Introduction .................................................................................................................................................... 7
QolorPoint Wireless Uplighter features ........................................................................................................................ 7
Product Contents .......................................................................................................................................................... 8
Charging......................................................................................................................................................... 8
User Interface................................................................................................................................................. 9
Power ............................................................................................................................................................................ 9
External Power (Optional Accessory) ........................................................................................................................... 9
Function Modes............................................................................................................................................ 10
Cust Col Mode Operation ........................................................................................................................................... 10
Static Mode Operation ................................................................................................................................................ 11
DMX Mode Operation ................................................................................................................................................. 12
Built-In Effects ............................................................................................................................................................. 13
SHoW DMX SHoW ID Settings .................................................................................................................... 14
SHoW DMX ID LED .................................................................................................................................................... 14
Lamp Profile.................................................................................................................................................. 15
Power Mode ................................................................................................................................................................ 15
Brightness Control ...................................................................................................................................................... 15
PWM Frequency Control ............................................................................................................................................ 15
Keypad Lock ............................................................................................................................................................... 16
Mechanical ................................................................................................................................................... 18
Dimensions ................................................................................................................................................................. 19
Antenna....................................................................................................................................................................... .20
Warranty .........................................................................................................................................................................22
Appendix 1- DMX Maping Table ......................................................................................................................................21
City Theatrical Inc. believes the information in this manual is accurate and complete however assumes no
responsibility for any error or omissions within this document or any other documentation accompanying the product.
We reserve the right to revise this document at any time.
Please see http://www.citytheatrical.com to download latest
version.
Product Modification
This City Theatrical product has been designed and manufactured to meet the strict requirements of U.S., EU and
International safety regulations. Any unauthorized modifications to the product including replacement of parts with
non-standard parts could compromise safety and result in the product being non-compliant with relevant standards.
There are no user serviceable parts within this product.
Radio Compliance Information
5792M SHoW DMX Neo® Radio Module
FCC ID: VU65792M
IC: 7480A-5792M
FCC Part 15
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
Radio Frequency Notifications
FCC Notifications
RF Radiation
The Product is an intentional radiator of Radio Frequency (RF) energy. In order to limit RF exposure to personnel in
the immediate area, the Product should be located and installed such that a separation of at least 8’’ (20 cm) is
maintained between the Product’s antenna and personnel in the vicinity of the device.
Modification Warning
Caution: changes or modifications to this equipment, not expressly approved by City Theatrical Inc. could void the
user’s authority to operate the equipment.
Industry Canada Notifications
This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Product Installation and Configuration Guide © City Theatrical Inc. 2007
CE Mark Conformity
Page 3 of 22
Disclaimer
Page 4 of 22
City Theatrical Inc. declares that this product conforms to the specifications listed in this manual, following the
provisions of the European R&TTE directive 1999/5/EC:
City Theatrical Inc. vakuuttaa täten että dieses produkt tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten
ja sitä koskevien näiden direktiivien muiden ehtojen mukainen.
City Theatrical Inc. déclare que le produit est conforme aux conditions essentielles et aux dispositions relatives à la
directive 1999/5/EC.
• EN 301 489-1, 301 489-17 General EMC requirements for Radio equipment.
• EN 60950 Safety
• EN 300 328 Technical requirements for Radio equipment.
CAUTION—this equipment is intended to be used in all EU and EFTA countries.
Outdoor use may be restricted to certain frequencies and/or may require a license for operation. Contact local
Authority for procedure to follow.
Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.
Product Installation and Configuration Guide © City Theatrical, Inc. 2015
Q52 Regulatory information
Radio Frequency Notifications
Belgique Dans le cas d'une utilisation privée, à l'extérieur d'un bâtiment, au-dessus d'un espace public, aucun
enregistrement n'est nécessaire pour une distance de moins de 300m. Pour une distance supérieure à 300m un
enregistrement auprès de l'IBPT est requise. Pour une utilisation publique à l'extérieur de bâtiments, une licence de
l'IBPT est requise. Pour les enregistrements et licences, veuillez contacter l'IBPT.
France 2.4 GHz Bande : les canaux 10, 11, 12, 13 (2457, 2462, 2467, et 2472 MHz respectivement) sont
complétement libres d'utilisation en France (en utilisation intérieur). Pour ce qui est des autres canaux, ils peuvent
être soumis à autorisation selon le départment. L'utilisation en extérieur est soumis à autorisation préalable et très
restreint. Vous pouvez contacter l'Autorité de Régulation des Télécommunications
(http://www.art-telecom.fr) pour de plus amples renseignements.
5792M SHoW DMX Neo Radio CE Declaration of Conformity
Page 5 of 22
System Compliance Information
The QolorStrip Wireless LED Batten
City Theatrical Incorporated declares that this product conforms to the specifications listed in this manual, following
the provisions of the European R&TTE directive 1999/5/EC:
Restrictions on Hazardous Substances (RoHS) (2002/95/CE)
Electromagnetic Compatibility (2004/108/EC).
Safety (EN 60950)
Technical requirements for radio equipment. (EN 300 328)
CAUTION—This equipment is intended to be used in all EU and EFTA countries.
Outdoor use may be restricted to certain frequencies and/or may require a license for operation. Contact local
Authority for procedure to follow.
WEEE & RoHS Statement
The European Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE), requires that products
must not be disposed of the normal unsorted municipal waste stream. Appliances must be collected separately in
order to optimize the recovery and recycling of the materials they contain and reduce the impact on human health and
the environment.
The consumer must contact their local authority or retailer for information concerning disposal of their products.
City Theatrical provides a take-back facility for batteries used within City Theatrical products, although the expense for
transport remains the liability of the consumer. Please contact City Theatrical directly if this service is required.
Safety Notices
Please read this entire manual before using your new equipment. Please keep the manual in a safe place so you can
refer to it in the future as required.
The QolorPoint battery powered LED uplighter is intended for use only by qualified professionals. Connection,
installation and hanging of this equipment must be performed in accordance with all pertinent local, regional and
national safety codes and regulations.
Be sure installation provides adequate ventilation. Some system components can produce significant heat and must
be properly installed to allow proper cooling and assure user safety. All sides of the equipment must be clear of
obstruction and allow free airflow.
There are no user-serviceable parts inside! Refer to qualified service personnel!
Page 6 of 22
Page 7 of 22
•AVOID direct eye exposure to the light source when illuminated
•DO NOT submerge this product in water
•DO NOT hang this product other than by the means indicated in this manual
•DO NOT leave any flammable material near product while operating or charging
•ALWAYS use the supplied charger or charging case
•ALWAYS ensure the charger is connected to the specified voltage
•ALWAYS ensure the charging case lid is open whilst plugged into mains supply
•NEVER connect this product or charger to a dimmer pack
•DO NOT operate this fixture if it appears damaged in any way
•DO NOT operate this fixture where the ambient temperature exceeds 115ºF (45ºC )
In the unlikely event that your product develops a fault, please contact your local dealer or authorized distributor.
Do not attempt to repair yourself unless specifically instructed by City Theatrical Inc.
Note: Restrictions apply to transporting this equipment on aircraft due to the lithium polymer
batteries having capacity greater than 100Wh. Please consult IATA Packing Instructions 967 and
City Theatrical Inc. for further information.
Introduction
The QolorStrip is a battery-powered wireless LED strip capable of providing portable and instant architectural and
feature lighting anywhere. With high-powered red, green, blue and white LEDs the fixture is capable of producing
any color or shade of white using combinations of those LEDs. Ideal for illuminating buildings in color, both indoors
and outdoors, the fixture is powerful enough to light buildings of 3 or 4 stories. Lighting effects may be created by
connecting to effects generators such as lighting desks or other CORE Master units using the in-built City Theatrical
Show DMX Neo Max Wireless DMX receiver. Simply connect wirelessly to the transmitter of the generator.
.
-
QolorStrip Battery Powered Wireless LED Strip features
•High powered 4,000 lumen RGBW LEDs equivalent to 9700 Lux @ 2m
•18 x Cree high-powered RGBW LED arrays
•Lithium Ion battery reducing unit weight to just 6.5kg with battery life of up to 8 hours
•Mains input allowing unit to run in a permanent installation plus mains out to other units
•LEE Filter Color library or separate RGBW control.
•City Theatrical Show DMX Neo Max wireless DMX as Master or Slave control
•4 or 5 or 8 or 72 Channel DMX operation and variable PWM frequency for TV work
•Cable DMX input plus DMX Output to other fixtures (incl ShowDMX to DMX conversion)
•Mounting options to allow unit to be floor mounted or fixed to truss or other mounting.
•IP65 outdoor rated case
•Operating temperature range -0 to +35 degree C or 32 to +95 degree F
Safety
Page 8 of 22
Product Contents
Please contact your dealer immediately if there are any signs of product damage or parts missing.
Single unit Charging case of four units
•1x QolorStrip wireless LED
fixture
•1x Power cable
•1x Quick Start Guide
• 4x QolorStrip Wireless LED
fixtures
• 1x Charging case
• 1x Powercon Cable
• 1x Manual
Getting Started
QolorStrip key Elements
Display
Charging Status LED
Power On/ Off
Show ID Screen
and LED indicator
Operation
Turning On and Off
•Push and hold this power button for >1 second to switch the unit ON or OFF
•The display will show “City Theatrical” and software version for a few seconds before starting
•The display backlight will extinguish after a short time to reduce power use
Battery Charging
•The fixture has a built-in charger optimized for the battery and will charge while attached to the
mains supply whether the unit is active or not
•Only use the supplied mains cable or charging case
•For best results recharge battery fully before storage
•When charging in the charging case, it is best to ensure the case
lid remains open to disperse heat, although the lid may be closed in cooler climates.
•Switch off the charger unit and unplug once fully charged
•While charging the LED indicator will illuminate in RED or AMBER
•(Red indicates an empty battery moving to Amber when significantly charged)
•Once fully charged the LED indicator will show GREEN Charging Charged
DO NOT use any charger other than the unit supplied with the QolorStrip
When using a charging flight case, ensure the unit is pushed fully down on the charging
connector. The charge light on side of the unit should illuminate to signify this has been done.
Page 9 of 22
Mains Power
•The fixture can be run from mains power attached to the “PowerCON” connector (PowerCON True1) on the side
•While running from mains the mains symbol is shown in the top right hand corner of the display.
•It will recharge the battery when mains is applied to the Powercon input connector but note that the rate of
charging is reduced if the fixture is on
•A Powercon mains output connector on the left side of the fixure allows mains to be daisy-chained from one
fixture to another.
Note that no more than 4 units can be daisy chained
Control Panels
Enables changes to FUNCTION or SETTINGS menus
Exits from the current option or menu
Navigates backward through the menu list
or increments a numeric value
or navigates forward through available values
Navigates forward through the menu list
or increments a numeric value
or navigates forward through available values
Enters the currently displayed menu option
or saves the currently displayed value
Page 10 of 22
Function Modes
There are four modes of Operation, accessed through the FUNCTION menu;
To change Function press . Use the buttons to select “CHANGE Function” and press to accept.
Then use the buttons to select the required function as above and press .
The four modes of operation are discussed in more detail below.
All of these adjust the brightness settings for each color.
Custom Color Mode Operation
Custom Colors
When in Custom Color mode, the display indicates the current selected color
Simply press to step through the colors or accept a color value.
Use keys to change the value.
Value range 0 to 255.
Tip: Mix red & blue for purple/pink
Tip: Mix red & green for orange/yellow
Custom
Color This mode allows the fixture to output a static Red, Green, Blue or White color, or any
combination thereof; each color may be set to any value 0 to 255.
Any SHoW DMX signal, if present, is ignored.
Static In this mode the fixture outputs a static LEE or preset ‘cc’ color as selected.
The selection is remembered if the unit is switched off then back on or put into another
mode.
Any SHoW DMX signal, if present, is ignored.
DMX In this mode the fixture is under control of SHoW DMX so may be controlled by a SHoW
DMX compatible device or DMX compatible device with a SHoW DMX transmitter
attached.
The options available within DMX mode are described in more detail below.
Effects In this mode the fixture generates a number of special effects. The speed of effect types
can be adjusted from 1 to 10.
Page 11 of 22
Tip: Mix red & green with White for warm shades of white.
Static Mode Operation
Static operation
When in STATIC mode the display indicates the current selected color.
To change the current selected color press .
The last character of the currently selected color is underlined.
Use the keys to select a color from the built-in library of 70 pre-programmed colors, including 60 popular LEE
Filter Colors
The color changes when cycling through the available options. The selected color is only saved when <ENTER> is
pressed. If <ENTER> is not pressed, the color reverts to the previously selected color after 8 seconds.
Available colors
cc001 White Lee075 Evening Blue Lee157 Pink
cc002 Half Flesh Tone Lee089 Moss Green Lee159 No Color Straw
cc003 Full Flesh Tone Lee100 Spring Yellow Lee162 Bastard Amber
cc004 Half Mint Green Lee101 Yellow Lee170 Deep Lavender
cc005 Mint Green Lee102 Light Amber Lee174 Dark Steel Blue
cc006 Half Ice Blue Lee103 Straw Lee181 Congo Blue
cc007 Full Ice Blue Lee104 Deep Amber Lee192 Flesh Pink
cc008 Soft Red Lee106 Primary Red Lee199 Regal Blue
cc009 Soft Green Lee107 Light Rose Lee323 Jade
cc010 Soft Blue Lee108 English Rose Lee341 Plum
Lee113 Magenta Lee345 Fuchsia
Lee002 Rose Pink Lee115 Peacock Blue Lee353 Lighter Blue
Lee009 Pale Amber Gold Lee117 Steel Blue Lee652 Urban Sodium
Lee010 Medium Yellow Lee118 Light Blue Lee722 Bray Blue
Lee013 Straw Tint Lee119 Dark Blue Lee724 Ocean Blue
Lee015 Deep Straw Lee121 Lee Green Lee738 Jazz Green
Lee017 Surprise Peach Lee126 Mauve Lee765 Lee Yellow
Lee019 Fire Lee127 Smoky Pink Lee776 Nectarine
Lee020 Medium Amber Lee135 Deep Amber Gold Lee777 Rust
Page 12 of 22
Lee024 Scarlet Lee136 Pale Lavender Lee779 Bastard Pink
Lee026 Bright Red Lee138 Pale Green Lee789 Blood Red
Lee046 Dark Magenta Lee139 Primary Green Lee793 Vanity Fair
Lee058 Lavender Lee147 Apricot Lee795 Magical Magenta
Lee068 Sky Blue Lee153 Pale Salmon
DMX Mode Operation
DMX Operation
City Theatrical QolorPoint is equipped with a SHoW DMX Neo wireless radio
transmitter and receiver. This allows the fixture color to be set up by or
synchronized with sequences produced by a DMX lighting controller or other
QolorPoint unit when in Receive, or SLAVE mode.
Alternatively when in MASTER mode the unit can be linked to many Slave units which will then duplicate everything
output from the Master.
If not using a QolorPoint as a Master unit then a compatible SHoW DMX transmitter attached to a DMX controller is
necessary, available separately.
When the ‘Function DMX’ screen is shown, after a few seconds the screen
automatically reverts to the last mode used, either Master or Slave. By pressing
the button the ‘DMX Type’ screen is shown, which allows the user to select
the opposite mode using button.
DMX Master Operation
Once Master mode is set, the Master may transmit to any number of slaves by
selecting a matching SHoW ID using the SHoW DMX ID button.
DMX Slave Operation
When in DMX Slave mode the display will show the current active DMX Start
Address so the unit can be controlled from elsewhere.
The number of channels occupied is dependent on the “DMX MODE” setting
(4 or 5 channels may be used by the fixture).
In this mode the entire universe is output on a side connector pin, for which a
connector cable is available from City Theatrical Inc. for connection to other non-wireless fixtures.
Page 13 of 22
DMX Start Address
To set the DMX start address press button when the display shows the current address. Use the buttons
to select the new start address then to confirm.
Built-In Effects
The QolorPoint is now equipped to generate a number of special effects as a
stand-alone unit when DMX is placed in Slave Mode or will output these to a
number of connected slave units when DMX is in Master Mode.
By pressing the button the last used effect type is brought up, which
can then be changed using the buttons.
By pressing the button to confirm the effect type, the speed can be
adjusted from a range 1 to 10 using the buttons.
When confirmed with the button the screen reverts to show the effect
and speed.
Page 14 of 22
SHoW DMX SHoW ID Settings
The QolorPoint uplighter uses the 5792M SHoW DMX Neo with Max Technology Radio Module. It is permanently
configured with six SHoW ID options for Adaptive Spread Spectrum Frequency Hopping and Neo Low Latency
broadcast mode. The SHoW ID can be changed by pressing the SHoW DMX ID button on the control panel of the
QolorPoint uplighter.
Color SHoW ID Description
Green 201 Neo Adaptive
Cyan 102 Neo Full Bandwidth
Magenta 117 Neo Low Limited Bandwidth
White 133 Neo Mid Limited Bandwidth
Red 149 Neo High Limited Bandwidth
Yellow 165 MAX Technology™
For QolorPoint Slave units to communicate with Master QolorPoint units or a lighting control desk, equipped with a
SHoW DMX transmitter connected to its DMX output, the SHoW ID LED color has to be the same.
This allows a group of QolorPoint fixtures to be controlled from the lighting desk or Master unit using the built-in color
cycles or set up individually selected colors across many units at once from just one Master unit.
SHoW DMX ID LED
The SHoW DMX LED color signifies the SHoW ID it is set to and indicates presence of DMX data.
Description for operation in Slave mode:
If the LED is FLASHING, the QolorPoint is not receiving DMX from a SHoW DMX transmitter.
If the LED is STEADILY ILLUMINATED the QolorPoint is connected with, and receiving DMX from a SHoW DMX
transmitter. This is a fully connected and fully functioning system.
Configuring with SHoW DMX Transmitter unit or QolorPoint Master unit
•Switch on the QolorPoint
•Set one unit to Master Mode and other units to Slave Mode
•Set the SHoW IDs on both Slave and Master to the same ID.
•Units will automatically connect when set to the same ID
For successful connection the receiver must fulfill the following conditions:
Page 15 of 22
Distance to transmitter (outdoors, and depending on conditions)
•Less than 1,500ft. for SHoW Baby or SHoW DMX Neo Transceiver
Distance between Master unit and Slave unit
• Less than 300ft
Position above obstacles (e.g. crowds and trees)
•Minimum 3ft
SHoW ID configuration between Slave and Master is remembered after power off or the battery is depleted.
This allows the system configuration to be set up in a warehouse and the whole system simply switched on at the site,
which makes deployment very simple.
Additional Settings
A number of additional settings may be accessed within the menu system:
Power Mode
Under the “CHANGE Settings” menu QolorPoint has two power modes that can be selected:
Power LongLife 50% Power
Power Normal Full Power
The “Normal” option provides maximum light output at the cost of reduced battery life.
“LongLife” reduces the LED output by 50%, therefore enables 2 x running period for ALL FUNCTIONS, whether
stand-alone or DMX.
To change the power mode press and use the buttons to select “CHANGE Settings” then press .
Use the buttons to select “POWER MODE” and press to select.
Use buttons to toggle between “Norm” and “LongLife” then press to save changes. This setting affects
all Static, Custom Color and DMX modes so that the battery life of each unit can be individually set, irrespective of
what’s controlling it.
Brightness Control
Under the “CHANGE Settings” menu QolorPoint has a separate brightness control that can control the output of the
unit in stand-alone mode:
The value may be changed from 0 to 100% in 1% increments:
Press and use the buttons to select “CHANGE Settings” then press to accept.
Use the buttons to select “BRIGHTNS CONTROL” and press to select.
Use buttons to toggle between “0%” and “100%” then press to save changes. This setting adjusts Static
and Custom Color modes only. DMX mode remains unchanged as the unit remains under external control.
PWM Frequency Control
For HD TV work QolorPoint is equipped with an option to adjust the PWM frequency of the LEDs to prevent ‘beating’
with the TV scan frequency.
To enable soft dimming press and use the buttons to select “CHANGE Settings” then press to
select.
Then use the buttons to select “PWM Freq” and press to select from value 244 Hz to 1.9kHz.
Page 16 of 22
Press to save changes and the screen will revert to showing the ‘Function’ mode.
Keypad Lock
The keypad may be locked to prevent tampering or inadvertent adjustment of the unit.
To Lock: Hold down the while switching ON the unit to Lock.
To Unlock: First switch OFF the unit. Hold down the while switching ON the unit to Unlock.
Mechanical
Locking
The unit may be locked to a nearby object by passing a locking wire or padlock through the locking holes in the top or
bottom plates.
Use keys to toggle between “0%” and “100%” then press to save changes. This setting adjusts Static, Cost
Col and Effect modes only.
In DMX slave mode the Brightness control will have no effect if the DMX mode includes dimmer data. Ie the Brightness
control will be inactive when set to 5 channel and 9 channel mode but active when 4 channel, 8 channel and 72 channel is
selected.
DMX Mode
The DMX channel mapping for each LED output on the fixture can be selected. A pixel consists of 4 LEDs: Red, Green.
Blue, White. Pixel 1 is the right-hand end LED cluster on the batten, pixel 18 is the left-hand end LED cluster.
DMX form
4 channel
5 channel
8 channel
9 channel
72 channel
All 18 pixels are controlled by 4 DMX channels for Red, Green Blue, White.
No dimmer channel
All 18 pixels are controlled by 4 DMX channels for Red, Green Blue, White and the 5th
channel controls the brightness (Dimmer channel)
Pixels 1 to 8 on RHS of fixture are controlled by channels 1 to 4
Pixels 9 to 18 on LHS of fixture are controlled by channels 5 to 8. No dimmer channel
Pixels 1 to 8 on RHS of fixture are controlled by channels 1 to 4
Pixels 9 to 18 on LHS of fixture are controlled by channels 5 to 8
Channel 9 controls the overall brightness (Dimmer channel)
Full pixel mapping such that each led in each pixel is controlled. No dimmer channel
A full mapping table is shown in Appendix 1 of this document.
Press and use the keys to select “CHANGE Settings” then press . to accept.
Use the keys to select “DMX Format” and press to select.
Use keys to toggle between 4, 5, 8, 9 or 72 Chan mode then press to save changes.
PWM Frequency Control
For HD TV work StripPoint is equipped with an option to adjust the PWM frequency of the LEDs to prevent ‘beating’
with the TV scan frequency.
Page 17 of 22
Press and use the keys to select “CHANGE Settings” then press . to
accept.
Use the keys to select “PWM Freq” and press to select.
Use keys to toggle between 4, 5, 8, 9 or 72 Channel mode then press to save changes.
Beware that when using the higher frequencies the resolution of the color intensity steps is reduced, so the
effect of color changing can become less smooth and more ‘steppy’.
Lamp Profile
The dimming curve can be selected to optimize for different applications
Press and use the keys to select “CHANGE Settings” then press . to accept.
Use the keys to select “Lamp Profile” and press to select.
Then use the keys to select “Sq. Law” or “Linear” curve. Press to save changes and the screen will revert
to showing the ‘Function’ mode.
W-DMX Power
The Wireless DMX can be turned off so the unit will only respond to, and transmit from, the physical DMX connectors
Press and use the keys to select “CHANGE Settings” then press . to
accept.
Use the keys to select “DMX Power” and press to select.
Then use the keys to select “On” or “Off”. Press to save changes and the screen will revert to showing the
‘Function’ mode.
Keypad Lock
The keypad may be locked to prevent tampering or inadvertent adjustment of the unit.
To Lock: Hold down the whilst switching ON the unit to Lock.
To Unlock: First switch OFF the unit. Hold down the whilst switching ON the unit to
Unlock.
Master Reset
All settings can be reset to the default factory set up by pressing the
keys while turning the unit on with the button.
Page 18 of 22
Page 19 of 22
Dimensions
31.50"
5.00"
6.2"
3.00"
32.88"
39.38"
1000 mm
76.2mm
157 mm
1000.25 mm
1.58 mm
835.15 mm
Mechanical
Dimensions
Length : 1000mm
Height: 157mm (with feet attached)
Width: 74mm
Weight: 6.0Kg
Floor mounting: the unit can be pivoted through 90 degrees providing vertical and horizontal beams
Truss mounting options: The unit is supplied with Adjustable feet designed to be attached to standard 10mm mountings.
Alternatively the QolorStrip can be attached to a baseplate using quick-release, ¼ turn fixings available from City
Theatrical Inc. This baseplate has 10mm fixings to be attached to trussing walls or other structures.
Safety Fixings: the QolorStrip has 10mm eyes in the back of the chassis and M10 blind mountings allowing a range of
safely clips to be attached
Antenna
The antenna is a high-gain type similar in performance to the Wireless Solutions W-DMX 2dB standard antenna
according to testing. This antenna is now fitted to all City Theatrical Inc. units.
Page 20 of 22
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
City Theatrical Legacy 7030 QolorStrip Wireless LED Strips Manuel utilisateur
- Catégorie
- Stroboscopes
- Taper
- Manuel utilisateur