3M 5908555 Lad-Saf X2 Vertical Cable Manuel utilisateur

1

A

C

B

E

D

F

USER INSTRUCTIONS

5908555 Rev. H

LAD-SAF X2

VERTICAL CABLE SAFETY SLEEVE

AND SYSTEM

EN 353-1:2014+A1:2017

PPE Regulation (EU) 2016/425

Regulation 2016/425 on personal protective equipment,

as amended to apply in GB

CE Type Test

No. 2777

Satra Technology Europe Ltd

Bracetown Business Park

Clonee,

Dublin

D15 YN2P

Ireland

CE Product Quality Control

No. 2797

BSI

The Netherlands B.V.

Say Building

John M. Keynesplein 9

1066 EP

Amsterdam

Netherlands

UKCA Type Test

No. 0321

SATRA Technology

Centre Limited, Wyndham

Way, Telford Way, Kettering,

Northamptonshire, NN16 8SD,

United Kingdom

UKCA Product Quality Control

UKCA Production Quality

Control

No. 0086

BSI

Kitemark Court

Davy Avenue

Knowlhill

Milton Keynes

MK5 8PP

United Kingdom

ANSI Z359.16 OSHA 1926.1053

OSHA 1910.29

CSA Z259.2.5

2

A

B

C

G

E

F

D

E

H

B

CG

3

B

A

4 5

A B C

A. B. C. D.

E. F. G.

6

2

A

3

7

™

I

™

E

™

B

E

H

C

™

C

E

J

B

1 2

3 4

5

4

8

A

9

BA C

D

E

10

9513846 Rev. G

3M.com/FallProtection

1-800-328-6146

Red Wing, MN 55066, USA

LAD-SAF™

2797 3/8” (9.5mm) CABLE

EN353-1:2014+A1:2017

ANSI Z359.16

OSHA 1926.1053

OSHA 1910.29

CSA Z259.2.5

6160030

6160054

6160052

6160065

6160047

EN353-1:2014+A1:2017

ANSI Z359.16

OSHA 1926.1053

OSHA 1910.29

CSA Z259.2.5

EN353-1:2014+A1:2017

AS/NZS 1891.3

TYPE 1

EN353-1:2014+A1:2017

ANSI Z359.16

OSHA 1926.1053

OSHA 1910.29

WARNING Failure to heed warnings may result in serious injury or death. Manufacturer's instructions

supplied with this product at time of shipment must be followed for proper installation, use, inspection and

maintenance. Unauthorized alteration or substitution of system elements or components is prohibited. Use

only with compatible personnel protective equipment as per manufacturer’s instructions. Before each use

inspect system visually for defects. Formally inspect system in accordance with instructions at least annually,

or in accordance with specied inspection criteria for the structure the system is secured to. Refer to

instructions for information on periodic formal inspections. Minimum spacing of users of this system is 20ft.

Do not remove this label.

Installation Date / Fecha de instalación

Date d’installation/ Date d’installation

Installed By / Instalado por

Installé par / Installé par

Max. Users Per System: 310 lbs (141kg) x

Peso máx. de usuarios por sistema: 141 kg (310 lb) x

Nombre max. d’utilisateurs par système: 141kg (310livres) x

Épaisseur Utilisateurs par système: 141kg (310lb) x

System Length / Longitud del sistema

Longueur du système / Longueur du système

Date of Manufacture / Fecha de fabricación

Date de fabrication / Date de fabrication

Date Inspected

Fecha de la inspección

Date d’inspection

System Serial No. / Número de serie del sistema

Numéro de série du système / Nº de série du système

STANDARDS SLEEVE

Anchorage requirements / Requisitos de anclaje

Exigences d’ancrage / Conditions exigées pour l’ancrage

x 1 = 2700lbs (12kN)

x 2 = 3320lbs (14.8kN)

x 3 = 3940lbs (17.5kN)

x 4 = 4560lbs (20.3kN)

ADVERTENCIA El incumplimiento de las instrucciones puede ocasionar lesiones graves o la muerte. Las

instrucciones del fabricante suministradas con este producto en el momento del envío deben respetarse para

una instalación, uso, mantenimiento e inspección correctos. Está prohibida la alteración o sustitución de los

elementos o componentes del sistema sin autorización. Úselo sólo con equipo de protección personal

compatible según las instrucciones del fabricante. Antes de cada uso, realice una inspección visual del

sistema en busca de defectos. Realice una inspección formal del sistema de acuerdo con las instrucciones, al

menos, una vez al año o según los criterios de inspección especicados para la estructura a la que está jado.

Consulte las instrucciones para obtener información sobre las inspecciones formales periódicas. El espacio

mínimo entre usuarios de este sistema es de 6 m (20 pies). No quite esta etiqueta.

AVERTISSEMENT Le non-respect des mises en garde peut entraîner des blessures graves, voire mortelles.

Le dispositif doit être installé, utilisé, inspecté et entretenu conformément aux instructions du fabricant

jointes au produit au moment de son expédition. Toute modication ou tout remplacement non autorisé(e)

des éléments ou des composants du système est interdit(e). N’utiliser que des équipements de protection

individuelle compatibles conformément aux instructions du fabricant. Avant chaque utilisation, inspecter le

système visuellement pour déceler les défauts. Inspecter formellement le système conformément aux

instructions au minimum une fois par an, ou selon les critères d’inspection spéciés pour la structure sur

laquelle le système est xé. Consulter les instructions pour plus d’information sur les inspections formelles

périodiques. L’espacement minimal entre les utilisateurs de ce système est de 6,1m (20pi). Ne pas enlever

cette étiquette.

AVERTISSEMENT Le non-respect des avertissements peut entraîner des blessures graves, voire mortelles.

Les instructions du fabricant fournies avec ce produit au moment de la livraison doivent être respectées an

d’assurer une installation, une utilisation, une inspection et un entretien adéquats. Toute modication ou tout

remplacement non autorisé des pièces ou des éléments du système est interdit. N’utilisez qu’avec un

équipement de protection individuelle compatible conformément aux instructions du fabricant. Avant chaque

utilisation, inspectez visuellement le système pour détecter tout défaut. Au moins une fois par année,

inspectez ociellement le système conformément aux instructions ou aux critères d’inspection spéciés pour

la structure à laquelle est xé le système. Consultez les instructions pour plus de détails sur les inspections

formelles périodiques. L'espacement minimum entre les utilisateurs de ce système est de 6,10m (20pi). Ne

retirez pas cette étiquette.

NORMAS MANGUITO

NORMES MANCHON

0086

12

3

4

56

7

8

9

11

9

10

F

E

Z359.16

SERIAL NO.

XXXXXXX

MODEL NO. 6160030

WARNING

L'omission de tenir compte des avertissements peut entraîner

Failure to heed warnings may result in serious injury or

death. Read and follow manufacturer's instructions supplied

with this product. Use only with

DBI-SALA approved system and

harness. Inspect before each use.

Attach sleeve to frontal d-ring on

harness with supplied connector.

Do not grasp the sleeve or cable

while actively climbing

.

des blessures graves ou la mort. Lisez et suivez les

instructions du fabricant fournies avec ce produit. Utiliser

uniquement avec le système et le harnais agréés

DBI-SALA. Inspecter avant chaque utilisation.

Attachez la douille à l'anneau en

d frontal sur le harnais avec le

connecteur fourni. Ne

saisissez pas le manchon

ou le câble tout en

grimpant activement.

9514021 Rev. D

140 KG

EN353-1:2014+A1:2017

AVERTISSEMENT

40-

ANSI

automatic, sternal

X 1

MAXI.

CSA

Z259.2.5

0086

2797

A

B

C

D

E

F

G

H

Z359.16

SERIAL NO. XXXXXXX

MODEL NO. 6160047

WARNING

L'omission de tenir compte des avertissements peut entraîner

Failure to heed warnings may result in serious injury or

death. Read and follow manufacturer's instructions supplied

with this product. Use only with

DBI-SALA approved system and

harness. Inspect before each use.

Attach sleeve to frontal d-ring on

harness with supplied connector.

Do not grasp the sleeve or cable

while actively climbing

.

des blessures graves ou la mort. Lisez et suivez les

instructions du fabricant fournies avec ce produit. Utiliser

uniquement avec le système et le harnais agréés

DBI-SALA. Inspecter avant chaque utilisation.

Attachez la douille à l'anneau en

d frontal sur le harnais avec le

connecteur fourni. Ne

saisissez pas le manchon

ou le câble tout en

grimpant activement.

9514022 Rev. D

X 1

MAXI.

140 KG

EN353-1:2014+A1:2017

AVERTISSEMENT

40-

ANSI

0086

2797

B

AB

C

D

E

H

G

F

C

A

(23cm)

9" MAX

DAB

5

11

C

ü

û

A

D

F

B

E

A

B

D

C

A ≥ 0.20 in

(5mm)

B

A

1 2

3

FORM NO: 5908247 REV: A 6

SAFETY INFORMATION

Please read, understand, and follow all safety information contained in these instructions prior to the use of this Vertical

System. FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY OR DEATH.

These instructions must be provided to the user of this equipment. Retain these instructions for future reference.

Intended Use:

This Vertical System is intended for use as part of a complete personal fall protection system.

Use in any other application including, but not limited to, material handling, recreational or sports related activities, or other activities not

described in the Product Instructions, is not approved by 3M and could result in serious injury or death.

This device is only to be used by trained users in workplace applications.

!WARNING

This Flexible Cable/Rigid Rail System is part of a personal fall protection system. It is expected that all users be fully trained in the

safe installation and operation of their personal fall protection system. Misuse of this device could result in serious injury or

death. For proper selection, operation, installation, maintenance, and service, refer to these Product Instructions and all manufacturer

recommendations, see a supervisor, or contact 3M Technical Service.

• To reduce the risks associated with working with a Flexible Cable/Rigid Rail System which, if not avoided, could result

in serious injury or death:

- Inspect all components of the system before each use, at least annually, and after any fall event. Inspect in accordance with the

Product Instructions.

- If inspection reveals an unsafe or defective condition in a component of the system, remove the component from service and

destroy it.

- Any Flexible Cable/Rigid Rail System that has been subject to fall arrest or impact force must be immediately removed from

service and all components must be inspected by a Competent Person prior to being used again.

- Do not connect to the system while it is being installed.

- Ensure the system is appropriately rated for the number of simultaneous users.

- When unpacking the cable it may rapidly uncoil. Use proper safety procedures and appropriate personal protective equipment

when unpacking cable.

- Only use approved connectors to attach body harness to the system. Do not use any additional connecting devices.

- Use only cable specied and approved in the Product Instructions.

- Do not interfere with the locking action of the shuttle/sleeve device. Only manipulate the device to attach and detach from the

system.

- Always maintain three points of contact while climbing. Refer to the Product Instructions for further information on proper

climbing technique.

- Ensure that fall protection systems/subsystems assembled from components made by dierent manufacturers are compatible

and meet the requirements of applicable standards, including the ANSI Z359 or other applicable fall protection codes, standards,

or requirements. Always consult a Competent and/or Qualied Person before using these systems.

• To reduce the risks associated with working at height which, if not avoided, could result in serious injury or death:

- Ensure your health and physical condition allow you to safely withstand all of the forces associated with working at height.

Consult with your doctor if you have any questions regarding your ability to use this equipment.

- Never exceed allowable capacity of your fall protection equipment.

- Never exceed maximum free fall distance of your fall protection equipment.

- Do not use any fall protection equipment that fails pre-use or other scheduled inspections, or if you have concerns about the use

or suitability of the equipment for your application. Contact 3M Technical Services with any questions.

- Some subsystem and component combinations may interfere with the operation of this equipment. Only use compatible

connections. Consult 3M prior to using this equipment in combination with components or subsystems other than those described

in the User Instructions.

- Use extra precautions when working around moving machinery (e.g. top drive of oil rigs), electrical hazards, extreme

temperatures, chemical hazards, explosive or toxic gases, sharp edges, or below overhead materials that could fall onto you or

your fall protection equipment.

- Use Arc Flash or Hot Works devices when working in high heat environments.

- Avoid surfaces and objects that can damage the user or equipment.

- Ensure there is adequate fall clearance when working at height.

- Never modify or alter your fall protection equipment. Only 3M or parties authorized in writing by 3M may make repairs to the

equipment.

- Prior to use of fall protection equipment, ensure a rescue plan is in place which allows for prompt rescue if a fall incident occurs.

- If a fall event occurs, immediately seek medical attention for the worker who has fallen.

- Do not use a body belt for fall arrest applications. Use only a Full Body Harness.

- Minimize swing falls by working as directly below the anchorage point as possible.

- If training with this device, a secondary fall protection system must be utilized in a manner that does not expose the trainee to

an unintended fall hazard.

- Always wear appropriate personal protective equipment when installing, using, or inspecting the device/system.

EN

7

;Prior to installation and use of this equipment, record the product identication information from the ID label in the

Inspection and Maintenance Log (Table 2) at the back of this manual.

;Always ensure you are using the latest revision of your 3M instruction manual. Visit the 3M website or contact 3M

Technical Services for updated instruction manuals.

PRODUCT DESCRIPTION:

Figure 1 illustrates the 3M™ DBI-SALA® Lad-Saf™ Ladder Safety System. The Lad-Saf Ladder Safety System is designed

to protect a worker in the event of a fall while climbing a xed ladder or similar climbing structure. The Lad-Saf System is

comprised of the Top Bracket, a wire cable, the Cable Sleeve, the Cable Guide, the System Tag, and the Bottom Bracket. The

Top Bracket (A) is secured at the top of the ladder and anchors the Cable (B) in coordination with the Bottom Bracket (F), which

is secured at the bottom of the ladder. The Cable Sleeve (C) moves up and down the Cable with the user and attaches to the

frontal D-Ring of the user’s harness. The Cable Guide (D) ensures that the Cable remains in place. The System Tag (E) displays

important safety information and should be placed at a point on or near the system. The System Tag is visible as Label “F” in

Figure 10.

Figure 2 illustrates components of the Lad-Saf X2 Cable Sleeve. The Cable Sleeve is comprised of the Upper Roller, the Rotating

Side Plate, the Handle, the Sleeve Body, the Locking Lever, the Lower Roller, the Carabiner, and the Locking Cam. The Upper

Roller (A) secures the Cable Sleeve to the Cable in coordination with the Lower Roller (F). The Rotating Side Plate (B) and

Handle (C) open to allow placement of the Cable Sleeve on the Cable. The Sleeve Body (D) makes up the main structure of the

Cable Sleeve. The Locking Lever (E) locks the Cable Sleeve and prevents unintentional opening of the device. The Locking Cam

(H) holds the Cable Sleeve in place when locked. The Carabiner (G) attaches to the front D-Ring of the user’s harness.

See Table 1 for Component Specications of the Lad-Saf X2 Vertical Cable Safety Sleeve and System.

Table 1 – Specications

System Specications:

System Installation: Installation Instructions System Type System Description

5908282 Vertical Lad-Saf Flexible Cable Safety

System

5903435 Vertical Lad-Saf Flexible Cable Safety

System with Swivel D-Ring

Lad-Saf Cable Sleeve:

Item Number Activation Force Max Deployment

Length Minimum Breaking

Strength Weight

6160030 450 lbf (2.0 kN) 4.0 in. (102 mm) 3,600 lbf (16 kN) 2.1 lb.

(1.0 kg)

6160047 450 lbf (2.0 kN) 4.0 in. (102 mm) 3,600 lbf (16 kN) 2.1 lb.

(1.0 kg)

Capacity: Each user must have a combined weight (clothing, tools, etc.) of 88 lb. to 310 lb. (40 kg to 140

kg). The Lad-Saf System may have up to four simultaneous users, but each Lad-Saf X2 Vertical

Cable Safety Sleeve may have only one user attached. For additional users, additional Cable

Sleeves must be used.

Anchorage

Requirements: Number of Users Anchorage Strength Number of Users Anchorage Strength

1 2,700 lbf (12 kN) 3 3,940 lbf (17.5 kN)

2 3,320 lbf (14.8 kN) 4 4,560 lbf (20.3 kN)

Service Temperature: -40°F to 140°F (-40°C to 60°C)

Standards: The Lad-Saf X2 Vertical Cable Safety Sleeve and System have been tested in accordance with the

standards identied on the front cover of these User Instructions.

Cable Specications: The Lad-Saf X2 Cable Sleeve may only be used with a 5/16 in. (8 mm) or 3/8 in. (9.5 mm)

diameter solid core cable. Use with any other cable is prohibited and could result in serious injury

or death.

Item Number Description Material Minimum

Breaking Strength Weight

6104XXX /

6134XXX 3/8 in. (9.5 mm),

1 x 7 Galvanized Steel 15,400 lbf

(68.4 kN) 0.27 lb. / ft.

(0.41 kg / m)

6105XXX /

6135XXX 3/8 in. (9.5 mm),

1 x 7 Stainless Steel 18,000 lbf

(80 kN) 0.27 lb. / ft.

(0.41 kg / m)

6106XXX /

6136XXX 3/8 in. (9.5 mm),

7 x 19 Galvanized Steel 14,400 lbf

(64 kN) 0.27 lb. / ft.

(0.41 kg / m)

6107XXX /

6137XXX 3/8 in. (9.5 mm),

7 x 19 Stainless Steel 12,000 lbf

(53.3 kN) 0.27 lb. / ft.

(0.41 kg / m)

8

Table 1 – Specications

Component Specications:

Lad-Saf Ladder Safety System:

Figure 1

Reference Component Materials

A Top Bracket Galvanized Steel or Stainless Steel

B Cable Galvanized Steel or Stainless Steel

C Cable Sleeve Stainless Steel

D Cable Guide Urethane

E System Tag Stainless Steel

F Bottom Bracket Galvanized Steel or Stainless Steel

Lad-Saf Cable Sleeve:

Figure 2

Reference Component Materials

AUpper Roller Nylon

BRotating Side Plate Stainless Steel

CHandle Stainless Steel

D Sleeve Body Stainless Steel

E Locking Lever Stainless Steel

F Lower Roller Nylon

G Carabiner 6160030: Zinc-Plated Steel

6160047: Stainless Steel

H Locking Cam Stainless Steel

9

1.0 PRODUCT APPLICATION

1.1 PURPOSE: The Lad-Saf™ Ladder Safety System is part of a personal fall protection system. When used in combination

with the Lad-Saf™ Detachable Cable Sleeve, the Lad-Saf Ladder Safety System is designed to protect a worker in the

event of a fall while climbing a xed ladder or similar climbing structure.

; Fall Arrest Only: Do not use the Lad-Saf Ladder Safety System for any purpose other than Fall Arrest.

1.2 STANDARDS: Your Ladder Safety System conforms to the national or regional standard(s) identied on the front cover

of these instructions. If this product is resold outside the original country of destination, the re-seller must provide these

instructions in the language of the country in which the product will be used.

1.3 SUPERVISION: Use of the Lad-Saf Ladder Safety System must be supervised by a Competent Person1. Installation of

the Lad-Saf Ladder Safety System must be supervised by a Qualied Person2.

1.4 TRAINING: The Lad-Saf Ladder Safety System must be installed and used by persons trained in its correct application.

This manual is to be used as part of an employee training program as required by national, regional, or local standards.

It is the responsibility of the installers of this equipment to ensure they are familiar with these instructions, trained in

the correct care and use of this equipment, and are aware of the operating characteristics, application limitations, and

consequences of improper use of this equipment.

1.5 RESCUE PLAN: When using this equipment and connecting subsystem(s), the employer must have a rescue plan and

the means at hand to implement and communicate that plan to users, authorized persons3, and rescuers4. A trained, on-

site rescue team is recommended. Team members should be provided with the equipment and techniques to perform a

successful rescue. Training should be provided on a periodic basis to ensure rescuer prociency.

1.6 INSPECTION FREQUENCY:

The Ladder Safety System shall be inspected by the user before each use and, additionally,

by a competent person other than the user at intervals of no longer than one year.

5

Inspection procedures are described in

the “Inspection and Maintenance Log”. Results of each Competent Person inspection should be recorded on copies of the

“Inspection and Maintenance Log”.

1.7 AFTER A FALL: If the Lad-Saf System is subjected to the forces of arresting a fall, it must be removed from service

immediately and clearly marked “DO NOT USE”. The Lad-Saf Cable Safety Sleeve and System must then be destroyed or

forwarded to 3M for replacement.

2.0 SYSTEM REQUIREMENTS

2.1 ANCHORAGE: Anchorage requirements vary with the fall protection application. Structure on which the

Ladder Safety System is placed or mounted must meet the Anchorage specications dened in Table 1.

2.2 HAZARDS: Use of this equipment in areas with environmental hazards may require additional precautions to prevent

injury to the user or damage to the equipment. Hazards may include, but are not limited to: heat, chemicals, corrosive

environments, high voltage power lines, explosive or toxic gases, moving machinery, sharp edges, or overhead materials

that may fall and contact the user or Personal Fall Arrest System.

2.3 CLIMB ASSIST COMPATIBILITY: Do not use a Powered Climb Assist (PCA) with a 3M Climbing Ladder Fall Arrest System

(CLFAS), including the Lad-Saf Vertical Lifeline System and Lad-Saf X2, X3 or X3+ Detachable Cable Sleeves, unless the PCA has

been veried by 3M as being compatible with 3M’s CLFAS. Failure to comply with this warning could result in a user’s fall not being

safely arrested in the event of a fall from height while using incompatible PCA and CLFAS systems. Contact 3M Technical Service at

3MFallProtectionT[email protected] with any questions.

; Use of Climb Assist Systems that are not compatible with 3M Vertical Systems could result in serious injury or death.

2.4 COMPONENT COMPATIBILITY: 3M equipment is designed for use with 3M approved components and subsystems only.

Substitutions or replacements made with non-approved components or subsystems may jeopardize compatibility of

equipment and may aect the safety and reliability of the complete system.

2.5 CONNECTOR COMPATIBILITY: Connectors are considered to be compatible with connecting elements when they

have been designed to work together in such a way that their sizes and shapes do not cause their gate mechanisms to

inadvertently open regardless of how they become oriented. Contact 3M if you have any questions about compatibility.

Connectors (hooks, carabiners, and D-rings) must be capable of supporting at least 5,000 lbf (22.2 kN). Connectors

must be compatible with the anchorage or other system components. Do not use equipment that is not compatible.

Non-compatible connectors may unintentionally disengage (see Figure 4). Connectors must be compatible in size, shape,

and strength. If the connecting element to which a snap hook or carabiner attaches is undersized or irregular in shape,

a situation could occur where the connecting element applies a force to the gate of the snap hook or carabiner (A). This

force may cause the gate to open (B), allowing the snap hook or carabiner to disengage from the connecting point (C).

Self-locking snap hooks and carabiners are required by ANSI Z359 and OSHA.

1 Competent Person: A person who is capable of identifying existing and predictable hazards in the surroundings or working conditions which are unsanitary,

hazardous, or dangerous to employees, and who has authorization to take prompt corrective measures to eliminate them.

2 Qualied Person: A person with a recognized degree, certicate or professional standing, or who by extensive knowledge, training and experience, has

successfully demonstrated his ability to solve or resolve problems relating to fall protection and rescue systems to the extent required by OSHA or other applicable

federal, state, and local regulations.

3 Authorized Person: A person assigned by the employer to perform duties at a location where the person will be exposed to a fall hazard.

4 Rescuer: Person or persons other than the rescue subject acting to perform an assisted rescue by operation of a rescue system.

5 Inspection Frequency: Extreme working conditions (harsh environments, prolonged use, etc.) may require increasing the frequency of Competent Person

inspections.

10

2.6 MAKING CONNECTIONS: Snap hooks and carabiners used with this equipment must be self-locking. Ensure all

connections are compatible in size, shape and strength. Do not use equipment that is not compatible. Ensure all

connectors are fully closed and locked.

3M connectors (snap hooks and carabiners) are designed to be used only as specied in each product’s user’s instructions.

See Figure 5 for examples of inappropriate connections. Do not connect snap hooks and carabiners:

A. To a D-ring to which another connector is attached.

B. In a manner that would result in a load on the gate. Large throat snap hooks should not be connected to standard

size D-rings or similar objects which will result in a load on the gate if the hook or D-ring twists or rotates, unless the

snap hook complies is equipped with a 3,600 lb (16 kN) gate. Check the marking on your snap hook to verify that it

is appropriate for your application.

C. In a false engagement, where features that protrude from the snap hook or carabiner catch on the anchor, and

without visual conrmation seems to be fully engaged to the anchor point.

D. To each other.

E. Directly to webbing or rope lanyard or tie-back (unless the manufacturer’s instructions for both the lanyard and

connector specically allows such a connection).

F. To any object which is shaped or dimensioned such that the snap hook or carabiner will not close and lock, or that

roll-out could occur.

G. In a manner that does not allow the connector to align properly while under load.

11

3.0 INSTALLATION

;For more information on Lad-Saf System installation procedures, refer to the product Installation Instructions. See

IFU 5908282 or IFU 5903435 for more information.

3.1 PLANNING: Plan your use of the Lad-Saf Ladder Safety System before starting work. Account for all factors that may

aect your safety before, during, and after a fall. Consider all requirements, limitations, and specications dened in

Section 2 and Table 1.

• Ensure the system is rated for the required number of users.

• There are hazards associated with connecting and disconnecting from the system. Use secondary fall arrest

protection. Ensure adequate anchor points, landing platforms, or other means are available at connection and

disconnection points to allow safe transitions to and from the system.

• A minimum fall clearance of 7.0 ft. (2.0 m) is required between the user’s feet and surface below. The user may not

be protected against hitting the ground or landing during the rst 7.0 ft. (2.0 m) of ascent or last 7.0 ft. (2.0 m) of

descent. Use proper climbing procedures (e.g. maintain three points of contact with hands and feet) when ascending

or descending any portion of the ladder unprotected by the Lad-Saf System.

• Use proper safety procedures when climbing. Do not carry tools or equipment by hand. Keep your hands free for

climbing. Secure carried items to avoid dropping them on climbers below. Climb within your ability. Long climbs may

require several rest stops during ascent or descent to avoid exhaustion. Use proper work positioning equipment for

rest breaks. Do not climb in high winds or severe weather.

• Ensure only one user is climbing between cable guides.

3.2 CONNECTING THE CABLE SLEEVE TO THE CARRIER CABLE: The Lad-Saf X2 Vertical Cable Safety Sleeve must be

connected to a 3M Lad-Saf Ladder Safety System to be used. See Figure 7 for reference. To connect the Lad-Saf X2 Cable

Sleeve to the carrier cable of the Lad-Saf System:

1. Position the sleeve so that the the “up” arrow on the sleeve (I) is pointing to the ascending direction.

2. Rotate the locking lever (E) to the unlocked position. Figure 3 shows locked (A) and unlocked (B) locking lever

positions. The locking lever is on both sides of the detachable cable sleeve for both right and left hand operation.

3. Pull back on the rotating side plate (B) to its furthest position. Once the rotating side plate is in its furthest

rotated position, the locking lever (E) may be released. The locking cam (H) will be fully extended.

4. Rotate the handle (C) to its full upright position. This will allow the locking cam to drop out of the way in order

to install the sleeve on the cable.

5. Hold the sleeve upright and insert the cable (J) through the slot on the side of the sleeve with a lifting

motion upwards. Position the cable in the sleeve recess. Release the handle (C), rotating side plate (B) and locking

lever (E) to lock the sleeve on the cable. Ensure the locking lever (E) is in the locked position before use.

3.3 CONNECTING THE CABLE SLEEVE TO THE HARNESS: Connection between the Cable Sleeve and the Full Body

Harness may be done before or after the Cable Sleeve has been installed onto the Lad-Saf System. A secondary Fall

Protection system is recommended when connecting to or disconnecting from the Lad-Saf System. Handling the sleeve

during ascent or descent exposes the user to fall hazards. The Lad-Saf System must have a maximum angle of 15° from

vertical at all times during use.

;Do not use other connecting devices or combine devices (e.g. Lanyard) with the connector supplied with Cable

Sleeve. Always use the carabiner connector supplied with the Cable Sleeve during use. Do not substitute with other

connectors.

• ASCENDING: To ascend the structure climb up while maintaining three points of contact at all times (with hands and

feet). The Lad-Saf X2 Cable Sleeve will follow the climber. The carrier cable is snapped out of the cable guides as they

are encountered. Do not handle or remove the sleeve from the carrier cable when passing the cable guides or

if the sleeve locks.

• DESCENDING: To descend the structure, climb down smoothly while maintaining three points of contact at all times

(with hands and feet). Allow the Lad-Saf X2 Cable Sleeve to “lead” the climber down. Climbing down out of position

(e.g., leaning back excessively or climbing erratically) may cause the sleeve to lock onto the carrier cable. If the sleeve

locks, climb upward slightly to allow the sleeve to unlock and then continue to descend the structure. Reconnect the

carrier cable into the cable guides after passing each cable guide. Do not handle or remove the sleeve from the

carrier cable when passing the cable guides or if the sleeve locks.

• DISCONNECT: When climbing is completed, disconnect the Cable Sleeve from the system. See Figure 2 for

component references.

1. Remove the sleeve from the cable by rotating the Locking Lever (E).

2. Pull back on the Side Plate (B) and pivot the Handle (C) to its full upright position.

3. the sleeve can now be removed from the cable and be properly stored.

4.0 USE

4.1 BEFORE EACH USE: Verify that your work area and Personal Fall Arrest System (PFAS) meet all criteria dened in

Section 2 and that a formal Rescue Plan is in place. Inspect the Lad-Saf System per the ‘User’ inspection points dened

on the “Inspection and Maintenance Log” (Table 2). If inspection reveals an unsafe or defective condition, do not use the

system. Remove the system from service immediately and clearly mark “DO NOT USE”. The Lad-Saf Vertical Cable Safety

Sleeve and System must then be destroyed or sent to 3M for replacement.

4.2 SYSTEM CONNECTIONS: The Lad-Saf System must be used with a Full Body Harness. The Full Body Harness to ANSI

2359.11, CSA Z259.10, EN 361, or other applicable national, regional, or local standard. For proper tting of your Full

Body Harness, refer to the manufacturer’s instructions. To connect to your Full Body Harness, connect the Carabiner of

12

the Lad-Saf System to the frontal D-Ring (A) of your Full Body Harness. Use with any other connector or D-Ring on your

Full Body Harness is prohibited.

;OSHA 1910.29 and OSHA 1926.1053 state that the length of connection between the carrier and attachment point

must not exceed 9 inches (23 cm).

5.0 INSPECTION

5.1 INSPECTION FREQUENCY: The Lad-Saf System must be inspected at the intervals dened in Section 1. Inspection

procedures are described in the “Inspection and Maintenance Log” (Table 2). Inspect all other components of the Fall

Protection System per the frequencies and procedures dened in the manufacturer’s instructions.

5.2 DEFECTS: If inspection reveals an unsafe or defective condition, or if any doubt should arise as to the condition of the

system, remove the Lad-Saf System from service immediately and clearly mark “DO NOT USE”. The Lad-Saf Vertical Cable

Safety Sleeve and System must then be destroyed or sent to 3M for replacement. Do not attempt to repair the system.

5.3 PRODUCT LIFE: The functional life of the Lad-Saf System is determined by work conditions and maintenance. As long as

the product passes inspection criteria, it may remain in service.

6.0 MAINTENANCE, SERVICING, STORAGE

6.1 CLEANING THE SYSTEM: See Section 5.0 for inspection-related maintenance issues. If the carrier cable becomes heavily soiled

with oil, grease, paint, or other substances, clean it with warm soapy water. Wipe o the cable with a clean, dry cloth. Do not

force dry with heat. Do not use acid or caustic chemicals that could damage the cable.

;Additional maintenance and servicing procedures must be completed by an authorized service center. Authorization

must be in writing.

6.2 CLEANING THE CABLE SLEEVE: A soiled Lad-Saf X2 Vertical Cable Safety Sleeve may be cleaned using the following

procedure:

1. Mix four parts warm water with one part mild cleaning solution (e.g. Simple Green or similar solution).

2. Submerge the Cable Sleeve in the solution and soak the entire Cable Sleeve in the mixture for 2-3 hours.

3. Remove the Cable Sleeve from the solution and rinse with warm water for at least 1 minute. Be sure to remove any

excess dirt build-up.

4. Allow the Cable Sleeve to air-dry for 24 hours prior to use. Using cool, forced air is acceptable.

5. See Figure 2 for reference. Apply a small amount of lubrication to pivot points (E) or at the base of the side plate (B).

6. Complete a pre-use inspection as specied in Section 5.3. Conrm no debris is lodged internally, which could aect

Cable Sleeve operation.

6.3 STORAGE AND TRANSPORTATION: Store the Lad-Saf X2 Vertical Cable Safety Sleeve in a cool, dry, clean

environment, out of direct sunlight. Avoid areas where chemicals vapors exist. Thoroughly inspect the sleeve after

extended storage.

Transport the Lad-Saf Cable Sleeve in an enclosure to protect it from any cuts, moisture or ultraviolet light. Avoid

corrosive, overheated or refrigerated atmospheres.

6.4 SERVICE: Only 3M or parties authorized in writing by 3M may make repairs to this equipment. If the Lad-Saf Vertical

Cable Safety Sleeve and System have been subject to fall force or inspection reveals an unsafe or defective conditions,

remove the system from service immediately and clearly mark “DO NOT USE”. The Lad-Saf Vertical Cable Safety Sleeve

and System must then be destroyed or sent to 3M for replacement.

7.0 RFID TAG

7.1 LOCATION: 3M product covered in these user instructions is equipped with a Radio Frequency Identication (RFID) Tag.

RFID Tags may be used in coordination with an RFID Tag Scanner for recording product inspection results. See Figure 8

for where your RFID Tag is located.

7.2 DISPOSAL: Prior to disposing of this product, remove the RFID Tag and dispose/recycle in accordance with local

regulations. For additional information on how to remove the RFID Tag, please refer to the website link below.

Do not dispose of your product as unsorted municipal waste. The crossed-out wheelie bin symbol indicates that

all EEE (Electrical and Electronic Equipment) must be disposed of according to local law through available return

and collection systems. Please contact your dealer or your local 3M representative for further information.

For more information, please visit our website: http://www.3M.com/FallProtection/RFID

13

8.0 LABELS and MARKINGS

8.1 LABELS: Figure 9 illustrates label locations on the Lad-Saf Ladder Safety System. Figure 10 illustrates each label in

detail. Labels without a listed location on the system must be placed at a location near the Lad-Saf System. Information

provided on each label is as follows:

AA) Cable Sleeve Model Number B) Serial Number C) Warning Statement - Follow all instructions for use.

D) Read all user instructions. E) One user maximum. F) Applicable Standard G) Notied Body Detail

H) User Weight Requirements

BA) Cable Sleeve Model Number B) Serial Number C) Warning Statement - Follow all instructions for use.

D) Read all user instructions. E) One user maximum. F) Applicable Standard G) Notied Body Detail

H) User Weight Requirements

CA) "Up" orientation of Cable Sleeve for use.

DA) Maximum distance allowed between system cable and harness attachment point is 9.0 in. (23 cm).

B) Do not use the Cable Sleeve with a Lanyard. Do not modify the system in any way.

EID/Lot Number (YYMMWWTT): YY = last two digits of year of manufacture. MM = month of manufacture. WW =

week of year of manufacture. TT = internal 3M use only.

F1) Installation Date 2) Installed By 3) Anchorage Requirements 4) Maximum Number of Users per System

5) System Length 6) Date of Manufacture 7) Date Inspected 8) Serial Number 9) System Warnings

10) Cable type and sleeve compatibility matrix along with standards certication. 11) RFID Tag (see Section 7.0)

14

Table 3 – Inspection and Maintenance Log

Serial Number(s): Date Purchased:

Model Number: Date of First Use:

Inspection Date: Inspected By:

Component: Inspection: (See Section 2 for Inspection Frequency)Pass Fail

Cable Sleeve

(Figure 2) Inspect the Handle (C) for bends, cracks, and deformities. All fasteners must

be securely attached. Operation of handle and cam must be free and smooth.

Springs must be secure and of sucient strength to pull handle down.

The Handle also acts as an energy absorber and fall indicator. The Handle will

be deformed if it has been used for fall arrest. Figure 11.3 shows an example

of a Handle that has not been used for fall arrest (A) and a Handle that has

been used for fall arrest and is deformed (B). If the Handle is deformed

greater than A = 1/2 inch (12.7mm) Do not use. The sleeve must be removed

from service.

Inspect the Locking Lever (E) for smooth operation, ensuring it springs back

into its locked position when released.

Inspect the Locking Cam (H) for wear. Conrm that there is no damage to the

cam.

Inspect the Locking Cam (H) by holding the sleeve vertically with the Handle

(C) in the upright position and shaking the sleeve up and down to simulate a

fall. The cam should rotate freely.

Inspect the Locking Cam (H) by positioning the sleeve horizontally with the

Handle (C) in the upright position and placing the sleeve on the back side on

a at surface with the Lad-Saf X2 label facing up. The cam should rotate fully

upwards to the top of the sleeve.

Inspect the operation of the Side Plate (B) by pulling it back to try to open the

cable slot. It must not rotate. If it does rotate without having to rotate the

Locking Lever (E), remove the sleeve from service.

Inspect the entire unit for signs of corrosion.

Top Bracket

(Figure 11.2) Inspect for proper installation per Lad-Saf™ Flexible Cable Vertical Safety

Systems Installation Instructions, 3M Fall Protection manual 5908282 or

5903435.

Check for visible damage or corrosion. Look for cracks, bends or wear that

could aect the strength and operation of the system. Inspect welds. Look for

cracked or broken welds that could aect strength of bracket. Replace parts if

defects are found.

Check for loose or missing fasteners that secure top bracket to structure

(bolts, clamp plates, U bolts). If fasteners are loose, re-tighten as necessary to

the torque levels listed in the Installation Instructions supplied with your Lad-

Saf Flexible Cable Safety System.

Inspect top plate for deformation. Gap shall be 0.20 inch (5 mm) minimum at

location A.

Ensure both the large pin (B) and the small pin are in place. Ensure the spring

gate (C) is in place.

Inspect the Single Point Anchor (D) for cracks or signs of damage. Inspect the

torque of the fastener. Ensure washer has visible markings.

Bottom Bracket

(Figure 11.1) Inspect for proper installation per Lad-Saf™ Flexible Cable Vertical Safety

Systems Installation Instructions, 3M Fall Protection manual 5908282 or

5903435.

Check for damage or corrosion. Look for cracks, bends or wear that could

aect the strength and operation of the system. Replace parts if defects are

found.

Check for loose or missing fasteners that secure bottom bracket to the

structure. If fasteners are loose, re-tighten as necessary to the torque levels

listed in the Installation Instructions supplied with your Lad-Saf Flexible Cable

Ladder Safety System.

Inspect the tension rod assembly. Make certain saddle clips securely retain the

cable. Check torque on saddle clamps; torque to 35 ft-lb (47 N-m). Replace or

retighten if defects are found.

15

Table 3 – Inspection and Maintenance Log

Serial Number(s): Date Purchased:

Model Number: Date of First Use:

Inspection Date: Inspected By:

Component: Inspection: (See Section 2 for Inspection Frequency)Pass Fail

Cable Guides

(Figure 1) Check cable guides for damage. Look for wear or damage to black urethane.

Cable guides should restrain the cable and prevent cable contact with the

ladder/structure. Cable guides should be positioned at approximately 20-40 ft.

(6-12 m) along the carrier cable, or closer if required. Replace parts if defects

are found.

Check cable guide fasteners. The fasteners should the secure cable guide in

position. Tighten as necessary.

Cable Guides

(Figure 1) Inspect the cable for corrosion, kinks or damage that will aect strength and

impede the cable sleeve from traveling on the cable. If there are any nicks or

kinks in the ladder cable, the cable must be inspected by a competent person

prior to use. Inspect for signs of abrasion against the ladder or structure.

Replace the cable if defects are found.

Inspect for proper tension. Groove should be exposed above bottom template

(see callout “E”, Figure 11.1). You should not be able to pull tension rod down

by hand. Cable should be tight enough to prevent contact with the ladder/

structure. Re-tension the cable if necessary. Do not over-tension the system.

Labels

(Figure 9) Ensure that all labels are present and fully legible.

PFAS and Other

Equipment Additional Personal Fall Arrest System (PFAS) equipment (harness, SRD, etc)

that are used with the Anchorage System should be installed and inspected per

the manufacturer’s instructions.

Structure Verify the structure to which the structure is attached meets the strength

requirements from Table 1 in all possible directions of loading.