Campbell Hausfeld PW320200 Mode d'emploi

Premium Pressure Washer

Operating Instructions

Model: PW320200

IN472000AV 01/17

A Marmon/Berkshire Hathaway Company

EN

If your pressure washer is not working properly or if there are parts missing or broken,

please DO NOT RETURN IT TO THE PLACE OF PURCHASE. Contact our Customer Service

Department at 1-855-504-5678 or www.campbellhausfeld.com

REGISTER YOUR PRODUCT ONLINE NOW! www.campbellhausfeld.com

READ AND FOLLOW ALL INSTRUCTIONS • SAVE THESE INSTRUCTIONS • DO NOT DISCARD

Please read and save these instructions. Read carefully before attempting to

assemble, install, operate or maintain the product described.

Protect yourself and others by observing all safety information. Failure to comply

with instructions could result in personal injury and/or property damage! Retain

instructions for future reference.

REMINDER: Keep your dated proof of purchase for warranty purposes. Attach it to

this manual or file it for safekeeping.

Model #: __________________________

Serial #: ___________________________

Purchase Date: _____________________

For parts, product & service information

visit www.campbellhausfeld.com

Campbell Hausfeld

100 Production Drive

Harrison, Ohio 45030

MAINTENANCE /

REPAIR

TROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

1

BEFORE YOU BEGIN

Description

Pressure Washer units are designed to provide high pressure water for cleaning applications. The pumps

and engines used in these applications are oil lubricated and should be checked for appropriate oil levels

between each use. The pressure washer units are to be used and maintained per the instructions in this

manual. Any other use of the pressure washer unit will void the warranty and the manufacturer will not be

responsible for problems or damages resulting from such misuse.

UNPACKING

After unpacking the unit, inspect carefully for any damage that may have occurred during transit. Check for

loose, missing or damaged parts. Check to be sure all supplied accessories are enclosed with the unit. In case

of questions, damaged or missing parts, please visit www.campbellhausfeld.com for customer assistance.

Do not operate unit if damaged during shipping, handling or use. Damage may result in

bursting and cause injury or property damage.

Required Items - Not Included

• Gasoline

• Water supply hose

• Water source

GENERAL SAFETY INSTRUCTIONS

Safety Guidelines

This manual contains information that is very important to know and understand. This information is

provided for SAFETY and to PREVENT EQUIPMENT PROBLEMS. To help recognize this information, observe

the following symbols.

Danger indicates an imminently hazardous situation which, if not avoided, WILL result in death

or serious injury.

Warning indicates a potentially hazardous situation which, if not avoided, COULD result in

death or serious injury.

Caution indicates a potentially hazardous situation which, if not avoided, MAY result in minor or

moderate injury.

Notice indicates important information, that if not followed, may cause damage to equipment.

IMPORTANT or NOTE: Information that requires special attention.

Safety Symbols

The following Safety Symbols appear throughout this manual to alert you to important safety hazards and

precautions.

Risk of

Explosion

Risk of Fire Risk of

Personal Injury

Wear Eye

Protection

Risk of ShockRisk of

Spillage

Risk of Hot

Parts

Risk of Falling Risk of

Chemical Burn

Risk of Injury

from Lifting

MANUAL

Read

Manual

First

RIsk of Funes

MAINTENANCE /

REPAIR TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS GETTING STARTED

2

GENERAL SAFETY INSTRUCTIONS (CONTINUED)

California Proposition 65

This product and its exhaust contain chemicals known to the State of California to cause cancer,

birth defects or other reproductive harm. In addition, some cleaning products and dust contain

chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Wash hands after

handling.

Important Safety Information

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the

product described. Protect yourself and others by observing all safety information. Failure to comply with instructions

could result in personal injury and/or property damage! Retain instructions for future reference.

This manual contains important safety, operational and maintenance information. If you have any

questions, please visit www.campbellhausfeld.com for customer assistance.

RISK TO BREATHING (ASPHYXIATION):

• Carbon Monoxide. Using an engine indoors can kill you in minutes. Engine exhaust contains high levels of carbon

monoxide (CO), a poisonous gas you cannot see or smell. You may be breathing CO even if you do not smell engine

exhaust.

• NEVER use an engine inside homes, garages, crawlspaces or other partly enclosed areas. Deadly levels of carbon

monoxide can build up in these areas. Using a fan or opening windows and doors does NOT supply enough fresh

air.

• ONLY use outdoors and far away from open windows, doors and vents. These openings can pull in engine exhaust.

• Even when the engine is used correctly, CO may leak into your home. ALWAYS use a battery-powered or battery

backup CO alarm in your house. Read and follow all directions for CO alarm before using. If you feel sick, dizzy or

weak at anytime, move to fresh air immediately. See a doctor. You could have carbon monoxide poisoning.

• Breathing ex haust fumes will cause se ri ous injury or death! En gine exhaust contains carbon mon ox ide, an odorless

and deadly gas. Operate pressure washer in a well-ventilated area. Avoid en closed areas such as ga rages, base-

ments, etc. Never op er ate unit in or near a lo ca tion occupied by humans or animals.

• Some clean ing fluids con tain substanc es which could cause injury to skin, eyes or lungs. Use only clean ing fluids

spe cif i cally rec om mend ed for high pressure washers. Fol low manufacturers recommendations. Do not use chlorine

bleach or any other corrosive compound.

Do not operate this unit until you read this instruction manual and the engine instruction

manual for safety, operation and maintenance instructions. If you have any questions regarding

the product, please visit www.campbellhausfeld.com

General Safety

RISK OF EXPLOSION OR FIRE:

• Spilled gas o line and it’s vapors can be come ignited from cigarette sparks, electrical arcing, exhaust gas es and hot

engine components such as the muffler. Shut off en gine and allow it to cool before adding fuel to the tank. Use care in

fill ing tank to avoid spill ing fuel. Move pressure wash er away from fueling area before start ing en gine.

• Heat will ex pand fuel in the tank which could result in spillage and pos si ble fire explosion. Keep maximum fuel

level 1/2” (12.7mm) be low bottom of filler neck to allow for expansion.

• Operating the pressure washer in an ex plo sive en viron ment could re sult in a fire. Operate and fuel equipment in

well-ventilat ed areas free from ob structions. Equip areas with fire extinguisher suit able for gas o line fires.

• Materials placed against or near the pressure washer can in ter fere with its proper ventilation fea tures caus ing

overheating and possible ig ni tion of the materials. Never op er ate pressure wash er in an area containing dry brush

or weeds.

• Muffler exhaust heat can damage paint ed sur fac es, melt any material sen si tive to heat (such as siding, plastic, rub-

ber, vinyl or the pressure hose, itself), and dam age live plants. Always keep pressure washer a minimum of 4’ (1.2m)

away from surfac es (such as houses, au to mo biles or live plants) that could be damaged from muffler exhaust heat.

• Improperly stored fuel could lead to acciden tal ignition. Fuel im prop er ly secured could get into the hands of

children or oth er un qual i fied persons. Store fuel in an OSHA approved contain er, in a se cure location away from

work area.

• Use of acids, toxic or cor ro sive chemicals, poisons, in sec ti cides, or any kind of flam ma ble solvent with this product

could re sult in se ri ous injury or death. Do not spray flammable liquids.

MANUAL

MAINTENANCE /

REPAIR

TROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

3

This product may not be equipped with a spark-arresting muffler. If the product is not equipped

and will be used around flam ma ble ma teri als or on land covered with materials such as

agricultural crops, forest, brush, grass or other similar items, then an ap proved spark arrester must be installed and is

legally required in the state of California. It is a violation of California statutes section 130050 and/or sec tions 4442 and

4443 of the California Public Re sourc es Code, unless the engine is equipped with a spark arrester, as defined in section

4442, and maintained in ef fec tive work ing order. Spark arresters are also required on some U.S. For est Service land and

may also be legally required under other statutes and or di nanc es.

RISK OF FLUID INJECTION AND LACERATION:

• Your pressure washer operates at fluid pressures and velocities high enough to penetrate human and animal flesh

which could result in amputation or other serious injury. Leaks caused by loose fittings or worn or damaged hoses can

result in injection injuries. DO NOT TREAT FLUID INJECTION AS A SIMPLE CUT! See a physician immediately!

- Inspect the high pressure hose regularly. Replace the hose immediately if it is damaged, worn, has melted from

contacting the engine, or shows any signs of cracks, bubbles, pinholes, or other leakage. Never grasp a high

pressure hose that is leaking or damaged.

- Never touch, grasp or attempt to cover a pinhole or similar water leak on the high pressure hose. The stream of

water IS under high pressure and WILL penetrate skin.

- Never place hands in front of noz zle.

- Direct spray away from self and others.

- Make sure hose and fit tings are tightened and in good condition. Never hold onto the hose or fittings during

op er a tion.

- Do not allow hose to contact muf fler.

- Never attach or remove wand or hose fittings while sys tem is pres sur ized.

- When using replacement lances or guns with this pressure washer, DO NOT use a lance and/or lance/gun

combination that is shorter in length than what was provided with this pressure washer as measured from the

nozzle end of the lance to the gun trigger.

• Injuries can result if system pressure is not reduced before attempting maintenance or disassembly. To relieve

sys tem pres sure, shut off engine, turn off water sup ply and pull gun trigger until water stops flowing. Use only

accessories rated equal to or higher than the rating of the pressure washer.

RISK OF INJURY FROM SPRAY:

• High-velocity fluid spray can cause objects to break, projecting particles at high speed. Always wear ANSI-approved

Z87.1 safety glasses. Wear protective clothing to protect against accidental spraying. Never point wand at or spray

people or animals.

• Light or unsecured objects can become hazardous projectiles. Always secure trigger lock when wand is not in

service to prevent accidental operation. Never permanently secure trigger in pull-back (open) position.

MAINTENANCE /

REPAIR TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS GETTING STARTED

4

GENERAL SAFETY INSTRUCTIONS (CONTINUED)

RISK OF UNSAFE OPERATION:

• Unsafe op er a tion of your pressure wash er could lead to se ri ous in ju ry or death to you or others.

- Do not use chlorine bleach or any other corrosive compound.

- Be come fa mil iar with the op er a tion and con trols of the pressure washer.

- Keep operating area clear of all persons, pets and obstacles.

- Do not operate the product when fatigued or under the influence of alcohol or drugs. Stay alert at all times.

- Never compromise the safety fea tures of this prod uct.

- Do not op er ate machine with missing, broken or un au tho rized parts.

- Never leave wand unattended while unit is running.

• If proper starting procedure is not followed, engine can kickback causing serious hand and arm injury. If engine

does not start after two pulls, squeeze trigger of gun to relieve pump pressure. Pull starter cord slowly until resistance

is felt. Then pull cord rapidly to avoid kickback and prevent hand or arm injury.

• The spray gun/wand is a powerful clean ing tool that could look like a toy to a child. Keep chil dren away from the

pressure washer at all times.

• Reactive force of spray will cause gun/wand to kickback, and could cause the op er a tor to slip or fall or misdirect the

spray. Im prop er control of gun/wand can re sult in in ju ries to self and

others.

- Do not over reach or stand on an unstable support.

- Do not use pressure washer while standing on a ladder.

- Grip gun/wand firmly with both hands. Expect the gun to kickback when triggered.

RISK OF INJURY OR PROP ER TY DAMAGE WHEN TRANSPORTING OR STORING:

• Fuel or oil can leak or spill and could result in fire or breathing hazard. Se rious in ju ry or death can re sult. Fuel or oil

leaks will dam age carpet, paint or oth er surfaces in ve hi cles or trailers.

- If pressure washer is equipped with a fuel shut-off valve, turn the valve to the OFF position before transporting

to avoid fuel leaks. If pres sure wash er is not equipped with a fuel shut-off valve, drain the fuel from tank before

trans port ing. Only trans port fuel in an OSHA-approved container.

- Al ways place pressure washer on a protective mat when transporting to protect against dam age to vehicle from

leaks.

• Oil could fill the cylinder and damage the engine if the unit is not stored or transported in an upright position.

Always transport and store unit in an upright position. Re move pres sure washer from vehicle immediately upon

arrival at your destination.

RISK OF ELEC TRI CAL SHOCK:

• Spray di rect ed at elec tri cal outlets or switch es, or ob jects con nect ed to an elec tri cal circuit, could re sult in a fatal

electrical shock. Unplug any elec tri cal ly op er at ed product before attempting to clean it. Direct spray away from

electric out lets and switches.

RISK OF CHEMICAL BURN:

• Use of acids, toxic or corrosive chemicals, poisons, in sec ti cides, or any kind of flam ma ble solvent with this product

could re sult in se ri ous injury or death.

- Do not spray ac ids, gasoline, ker o sene, or any other flammable materials with this product. Use only household

de ter gents, cleaners and degreasers recommended for use with pres sure washers.

- Wear pro tec tive clothing to protect eyes and skin from con tact with sprayed materials.

MAINTENANCE /

REPAIR

TROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

5

RISK OF BURSTING:

• High-velocity fluid spray directed at pneumatic tire sidewalls (such as found on automobiles, trailers and the like)

could damage the sidewall resulting in serious injury. On pressure washers rated above 1600PSI (11032kPa) use

the widest fan spray (40º nozzle) and keep the spray a minimum of 8” (20 cm) from the pneumatic tire sidewall. Do

not aim spray directly at the joint between the tire and rim.

RISK OF HOT SURFACES:

• Con tact with hot sur fac es, such as engine exhaust com po nents, could result in se ri ous burn. During op er a tion,

touch only the control surfaces of the pres sure washer. Keep children away from the pres sure washer at all times.

They may not be able to recognize the haz ards of this product.

RISK OF INJURY FROM LIFTING:

• Serious injury can result from attempting to lift too heavy an object. The pressure washer is too heavy to be lifted

by one person. Obtain assistance from others before lifting.

The DANGER, WARNING, CAUTION, and NOTICE notifications and instructions in this manual cannot

cover all possible conditions and situations that may occur. It must be understood by the operator that

caution is a factor which cannot be built into this product, but must be supplied by the operator.

SAVE THESE INSTRUCTIONS

DO NOT DISCARD

MAINTENANCE /

REPAIR TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS GETTING STARTED

6

SPECIFICATIONS

PW320200

Maximum PSI * 3200 PSI

Maximum GPM * 2.4 GPM

High Pressure Hose 25 ft (7.6 m)

Pressure of Inlet Water 20 PSI to 100 PSI

Inlet Water Cold Tap (100° F max.)

Soap Consumption Rate 10% max.

Unit Weight 60 lbs.

* Rated Pressure and Rated Water Flow is within manufacturing tolerance of (+/- 10%).

In a continued commitment to improve quality, the manufacturer reserves the right to make component changes, design

changes, or specification changes when necessary and without notice.

DIMENSIONS

PW320200

Length 34.75 in.

Width 21 in.

Height 23.25 in.

MAINTENANCE /

REPAIR

TROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

7

GETTING TO KNOW YOUR UNIT

NOTE: Photographs and line drawings used in this manual are for reference only and do not represent a specific model.

Compare the illustrations with your unit to familiarize yourself with the location of various controls and adjustments.

Save this manual for future reference.

NOT SHOWN:

Detergent Siphon Hose:

Feeds cleaning agents into the pump to mix with the water. See

How To Apply Chemicals/Cleaning Solvents

instructions in

Operation

section.

High Pressure Hose: Carries the pressurized water from the pump to the gun and spray wand.

Spray Gun: Connects with spray wand to control water flow rate, direction and pressure.

Spray Wand: See How To Use Spray Wand instructions in Operation section.

BASIC ELEMENTS OF AN ENGINE

Refer to the Engine Owner’s Manual for location and operation of engine controls.

Choke Control: Opens and closes carburetor choke valve.

Starter Grip: Pulling starter grip operates recoil starter to crank engine.

Engine Switch: Enables and disables ignition system.

Figure 1 - PW320200

Engine: Drives the high

pressure pump. Refer

to the Engine Owner’s

Manual for location

and operation of engine

controls.

Handle

Frame

High Pressure Pump: Increases the

pressure of the water supply.

Pump Outlet

Pump Inlet

Quick Connect Nozzles

MAINTENANCE /

REPAIR TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS GETTING STARTED

8

QUICK SETUP GUIDE

To reduce the risk of injury, read the pressure washer instruction manual and the engine

instruction manual before operating pressure washer.

Install the Handle

Place handle onto frame, depress the snap buttons, and slide the handle assembly

onto the frame until snap buttons snap into place.

Add/Check Oil

The engine is shipped without oil. Before starting engine, add the oil provided.

Check oil level prior to each use. Refer to Engine Owner’s Manual for complete

procedure.

Add Gasoline

In a well ventilated outdoor area add fresh, high quality, unleaded gasoline with

a pump octane rating of 86 or higher. Do not overfill. Wipe up spilled fuel before

starting the engine. Refer to Engine Owner’s Manual for complete procedure.

IMPORTANT: Ethanol ShieldTM (sold separately) is a fuel stabilizer that helps

eliminate and prevent ethanol related problems in power equipment. Follow the

instructions on the container and add to the gasoline.

QUICK START GUIDE

• Never run engine indoors or in enclosed, poorly ventilated areas. Engine exhaust contains carbon monoxide, an

odorless and deadly gas.

• Risk of fluid injection and laceration. When using the high-pressure setting, DO NOT allow the high-pressure spray

to come in contact with unprotected skin, eyes or with any pets or animals. Serious injury will occur.

Connect Garden Hose to Pump

Thread the garden hose to the pump inlet.

Connect High Pressure Hose to Pump

Connect the high pressure hose to the pump outlet.

Connect High Pressure Hose to Spray Gun

Thread the other end of the high pressure hose to the spray gun.

Figure 2 - Install handle

Figure 3 - Add/check oil

Figure 4 - Add gasoline

Figure 5

Figure 6

Figure 7

MAINTENANCE /

REPAIR

TROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

9

Connect Spray Wand to Spray Gun

Thread the spray wand into the end of the spray gun.

Connect QC Nozzles to Spray Wand

Pull quick connect coupler back and insert nozzle. Release quick connect coupler and twist

nozzle to make sure it is secure in coupler.

Turn Water Faucet Completely On

Do not run the unit without water supply connected and turned on. Use Cold Water Only.

Release Air from System

Release all air from pump and high pressure hose by depressing trigger until a steady stream

of water is present. Approximately 30 seconds.

Move the Lever to the CHOKE Position

Pull the Recoil Starter Grip

Pull the recoil starter grip to start the engine.

Gradually move the Lever to the FAST Position after engine starts.

This Guide is not a substitute for reading the operator’s manual. User must read

and understand operator’s manual before using this product.

30 S

Figure 8

Figure 9

Figure 10

Figure 11

Figure 13

Figure 14

Figure 12

MAINTENANCE /

REPAIR TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS GETTING STARTED

10

ASSEMBLY INSTRUCTIONS (FIGURES 15 AND 16)

1. Locate and remove all loose parts from the carton.

2. Cut four corners of the carton from top to bottom and lay the

panels flat.

3.

Place handle (G) onto frame (H),depress the snap buttons, and

slide the handle assembly onto the frame until snap buttons

snap into place.

Risk of personal injury. Avoid placing hands

between handle and frame when assembling to

prevent pinching.

4. Remove the colored quick-connect nozzles (K)

from the plastic bag and insert them into correct

grommet on the nozzle holder. Nozzles are color

coded to match colored nozzles on label.

5. Connect wand (E) to gun (D). Tighten securely.

6. Attach high pressure hose (C) to gun (D). Tighten

se cure ly.

The engine is shipped without oil. Before starting engine, add the oil provided. Damage to the

engine will occur if the engine is run without oil, this damage will not be covered under

warranty.

NOTE: The pump on this unit is maintenance free and requires no oil. If there is a problem with the pump,

contact our Customer Service Group on www.campbellhausfeld.com as soon as possible.

OPERATING INSTRUCTIONS

Pressure Washer Terminology

PSI: Pounds per Square Inch. The unit of measure for water pressure. Also used for air pressure, hydraulic

pressure, etc.

GPM: Gallons per Minute. The unit of measure for the flow rate of water.

CU: Cleaning Units. GPM multiplied by PSI equals CU.

Bypass Mode: Allows water to re-circulate within the pump when the gun trigger is not pulled. This feature

allows the operator to release the trigger gun and reposition themselves without having to turn the engine

off in between cleaning actions.

Do not allow the unit to run for more than two minutes without the gun trigger being pulled.

This could cause overheating and damage to the pump. When the temperature inside the pump

rises too high, the thermal relief valve will open and release a spray of water from the pump to lower the internal

temperature. The valve will then close.

Thermal Relief Valve (Figure 17): When the temperature inside the pump rises too high, this

valve will open and release a gush of water in an effort to lower the temperature inside the

pump. The valve will then close.

Detergent Injection System: Mixes cleaners or cleaning solvents with the water to improve

cleaning effectiveness.

Water Supply: All pressure washers must have a source of water. The minimum requirements for a water

supply are 20 PSI and 5 Gallons Per Minute. If your water source is a well, the garden hose length can only

be 30ft. (9m) max.

To reduce the possibility of contamination always protect against backflow when connected to

a potable water system.

G

H

K

E

D

CD

L

Figure 15

Figure 16

Figure 17

MAINTENANCE /

REPAIR

TROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

11

Pressure Washer Operating Features

PRESSURE ADJUSTMENTS

The pressure setting is preset at the factory to achieve op ti mum pres sure and cleaning. If you need to lower

the pres sure, it can be accomplished by these meth ods.

1. Back away from the sur face to be cleaned. The further away you are, the less the pressure will be on

the surface to be cleaned.

2. Change to the 40˚ nozzle (white). This nozzle delivers a less powerful stream of water and a wider spray

pattern. Refer to How To Use Spray Wand.

DO NOT attempt to increase pump pressure. A higher pressure setting than the factory set

pressure may damage pump.

How To Use Spray Wand

The nozzles for the spray wand are stored in the nozzle holder on the panel assembly. Colors on the panel

identify nozzle location and spray pattern. Refer to the following chart to choose the correct nozzle for the

job to be performed.

NOZZLE

COLOR

SPRAY

PATTERN USES SURFACES*

Red

0˚ powerful pinpoint

for spot cleaning

of hard, unpainted

surfaces or for high

reach areas

unpainted metal or

concrete;

DO NOT use on wood

Yellow

15˚ intense cleaning

of unpainted hard

surfaces

grills, driveways, concrete

or brick walkways,

unpainted brick or stucco

Green

25˚ intense cleaning of

larger areas

metal, concrete or wood

White

40˚ cleaning of painted

or delicate surfaces

Auto/RV, marine, wood,

painted brick and stucco,

vinyl, painted siding

Black

low pressure applies cleaning

solutions

Low pressure spray is safe

on all surfaces. Always

verify compatibility of

cleaning solution prior to

use.

The high pressure spray from your pressure washer is

capable of causing damage to surfaces such as wood, glass,

automobile paint, auto striping and trim, and delicate objects such as flowers and

shrubs. Before spraying, check the item to be cleaned to assure yourself that it is

strong enough to resist damage from the force of the spray.

Changing Nozzles on Spray Wand (Fig. 18)

Risk of fluid injection. Do not direct discharge stream toward persons,

unprotected skin, eyes or any pets or animals. Serious injury will occur.

Flying objects could cause risk of serious injury. Do not attempt to change

nozzles while pressure washer is running. Turn engine off before

changing nozzles.

1. Pull quick-connect coupler (E) back and insert nozzle (K).

2. Release quick-connect coupler and twist nozzle to make sure it is secure in coupler.

Flying object could cause risk of serious injury. Ensure nozzle is completely inserted in quick-

connect socket and quick-connect collar is fully engaged (forward) before squeezing gun trigger.

KE

Figure 18

MAINTENANCE /

REPAIR TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS GETTING STARTED

12

OPERATING INSTRUCTIONS (CONTINUED)

How To Apply Chemicals/Cleaning Solvents (Figure 19)

Applying chemicals or cleaning solvents is a low pressure operation. NOTE: Use only

soaps and chemicals designed for pressure washer use. Do not use bleach.

TO APPLY CHEMICALS:

1. Ensure detergent siphon hose (Figure 19) is attached to barbed fitting location

near high pressure hose connection of pump as shown.

2. Place other end of detergent siphon hose with filter on it into container holding

chemical/cleaning solution. NOTE: For every 7 gallons of water pumped 1 gallon of

chemical/cleaning solution will be used.

3. Install low pressure (black) nozzle into quick connect fitting of spray wand, see How To Use Spray Wand

paragraph in this section.

4. After use of chemicals, place detergent siphon hose into container of clean water and draw clean water

through chemical injection system to rinse system thoroughly. If chemicals remain in the pump, it could

be damaged. Pumps damaged due to chemical residue will not be covered under warranty.

NOTE: Chemicals and soaps will not siphon if the soap nozzle is not selected on the 5n1 Multi-tip Nozzle.

Starting (Figure 20)

To reduce the risk of injury, read the pressure washer instruction manual and the engine

instruction manual before starting pressure washer.

Risk of fluid injection and laceration. When using the high pressure setting, DO NOT allow the

high pressure spray to come in contact with unprotected skin, eyes, or with any pets or animals.

Serious injury will occur.

• Your washer operates at fluid pressures and velocities high enough to penetrate human and animal

flesh, which could result in amputation or other serious injury. Leaks caused by loose fittings or worn or

damaged hoses can result in injection injuries. DO NOT TREAT FLUID INJECTION AS A SIMPLE CUT! See a

physician immediately!

Carbon Monoxide. Using an engine indoors can kill you in minutes. Engine exhaust contains

high levels of carbon monoxide (CO), a poisonous gas you cannot see or smell. You may be

breathing CO even if you do not smell engine exhaust.

• Breathing ex haust fumes will cause se ri ous injury or death! En gine exhaust contains carbon mon ox ide,

an odorless and deadly gas.

• Operate pressure washer in a well-ventilated area. Avoid en closed areas such as ga rages, base ments,

etc.

• Never op er ate unit in or near a lo ca tion occupied by humans or animals.

Risk of Fire, Asphyxiation and Burn. Never fill fuel tank when engine is running or hot. Do not

smoke when filling fuel tank.

• Never fill fuel tank completely. Fill tank to 1/2” (12.7mm) below bottom of filler neck to provide space

for fuel expansion. Wipe any fuel spillage from engine and equipment before starting engine.

• DO NOT let hoses come in contact with very hot engine muffler during or immediately after use of

your pressure washer. Damage to hoses from contact with hot engine surfaces will NOT be covered by

warranty.

Risk of property damage. Never pull water supply hose to move pres sure washer. This could

damage hose and/or pump inlet.

• DO NOT use hot water, use cold water only.

• Never turn water supply off while pressure washer engine is running or damage to pump will result.

• DO NOT stop spraying water for more than two minutes at a time. Pump operates in bypass mode

when spray gun trigger is not pressed. If pump is left in bypass mode for more than two minutes

internal components of the pump can be damaged.

If you do not understand these precautions, please visit www.campbellhausfeld.com.

Prior to starting, refer to your engine manual for proper starting procedure.

F

Figure 19

MAINTENANCE /

REPAIR

TROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

13

1. In a well ventilated outdoor area add fresh, high quality, unleaded gasoline with a pump octane

rating of 86 or higher. Do not overfill. Wipe up spilled fuel before starting the engine. Refer to Engine

Owner’s Manual for correct procedure.

Use of fuels with greater than 10% ethanol are not approved for

use in this product per EPA regulations and will damage the unit

and void the warranty.

2. Check engine oil level. Refer to Engine Owner’s Manual for correct procedure.

3. Connect the water hose to the water source. Turn the water source on to remove all air from the hose.

When a steady stream of water is present, turn the water source off.

4. Verify the filter screen (M) is in water inlet of pump. NOTE: Convex side faces out.

I

C

N

J

M

5. Connect water source (N) to pump inlet (J). NOTE: Water source must provide a minimum of 5 gallons

per minute at 20 PSI.

6. Connect high pressure hose (C) to pump outlet (I).

To reduce the possibility of contamination always protect against backflow when connected to

a potable water system.

7. Choose the correct nozzle for the job to be performed. See How To Use spray Wand instructions in this

section. NOTE: If applying a chemical or cleaning solution, see How To Apply Chemicals/Cleaning

Solvents instructions in this section.

8. Turn water source on.

Risk of property damage. Failure to do so could cause damage to the pump.

9. Remove all air from the pump and high pressure hose by depressing trigger until a steady stream of

water is present.

10. Start engine. See Engine Owner’s Manual for correct procedure.

Risk of unsafe operation. If engine does not start after two pulls, squeeze trigger of gun to

relieve pump pressure. Pull starter cord slowly until resistance is felt. Then pull cord rapidly to

avoid kickback and prevent hand or arm injury.

NOTE: If the oil level in the engine is low, the engine will not start. If the engine does not start, check the oil

level and add oil as needed.

11. Depress trigger on gun to start water flow.

Risk of unsafe operation. Stand on a stable surface and grip gun/spray wand firmly with both

hands. Expect the gun to kick when triggered.

12. Release trigger to stop water flow.

Do not allow the unit to run for more than two minutes without the gun trigger being pulled.

This could cause overheating and damage to the pump. When the temperature inside the pump

rises too high, the thermal relief valve will open and release a spray of water from the pump to lower the internal

temperature. The valve will then close.

Figure 20

MAINTENANCE /

REPAIR TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS GETTING STARTED

14

OPERATING INSTRUCTIONS (CONTINUED)

Risk of injury from spray. Always engage the trigger lock (O) when gun is

not in use. Failure to do so could cause accidental spraying.

Shutting Down

1. After each use, if you have applied chemicals, place detergent siphon hose into

container of clean water and draw clean water through chemical injection system to rinse system

thoroughly.

Risk of property damage. Failure to do so could cause damage to the pump.

2. Turn engine off. See Engine Owner’s Manual.

Risk of property damage. NEVER turn the water off with the engine running.

3. Turn water source off.

4. Pull trigger on spray gun to relieve any water pressure in hose or spray gun.

NOTE: Failure to release system pressure will prevent removal of high pressure hose from spray gun or

pump connection.

5. See Storage section in this manual for proper storage procedures.

O

Figure 21

TROUBLESHOOTING GUIDE

SYMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION

Engine will not start (see

Engine Owner's Manual for

further engine

troubleshooting)

1. No fuel 1. Add fresh fuel

2. Pressure builds up after two pulls on

the recoil starter or after initial use

2. Squeeze gun trigger to relieve pres sure

3. Choke lever in the "No Choke" position 3. Move choke to the "Choke" po si tion

4. Spark plug wire not attached 4. Attach spark plug wire

5. Engine switch in OFF po si tion. 5. Place engine switch in ON position.

6. Choke lever in the "Choke" position

on a "hot" engine or an engine that

has been exposed to thermal heat for a

long period of time.

6. Move choke to the "No Choke" po si tion.

No or low pressure (initial use) 1. Spray wand not in high pressure 1. See How to Use Spray Wand instructions in the

Operation Section

2. Low water supply 2. Water supply must be at least 5 gpm @ 20 PSI

3. Leak at high pressure hose fitting 3. Repair leak. Apply sealant tape if necessary

4. Nozzle obstructed 4. See Nozzle Cleaning instructions in the Maintenance

section

5. Water filter screen clogged 5. Remove and clean filter. See Cleaning Water Inlet

Filter paragraph in the Maintenance section for the

correct procedure

6. Air in hose 6. Turn off the engine, then the water source.

Disconnect the water source from the pump inlet and

turn the water source on to remove all air from the

hose. When there is a steady stream of water present,

turn water source off. Re- con nect water source to

pump inlet and turn on wa ter source. Squeeze trigger

to re move re main ing air

7. Choke in the “Choke” position 7. Move choke to the “No Choke” po si tion

8. High pressure hose is too long 8. Use high pressure hose under 100 feet (30m)

Will not draw chemicals 1. Spray wand not in low pressure 1. See How to Use Spray Wand paragraph in the

Operation Section

2. Chemical filter clogged 2. Clean filter

3. Chemical screen not in cleaning

solution

3. Make sure end of detergent siphon hose is fully

submerged into cleaning solution

4. Chemical too thick 4. Dilute chemical. Chemical should be the same

consistency as water

5. Pressure hose is too long 5. Lengthen water supply hose instead of high pressure

hose

6. Chemical build up in chemical injector 6. Please contact our customer service department at

1-855-504-5678 or www.campbellhausfeld.com

No or low pressure

(after period of normal use)

1. Worn seal or packing 1. Please contact our customer service department at

1-855-504-5678 or www.campbellhausfeld.com

2. Worn or obstructed valves 2. Please contact our customer service department at

1-855-504-5678 or www.campbellhausfeld.com

3. Worn unloader piston 3. Please contact our customer service department at

1-855-504-5678 or www.campbellhausfeld.com

Water leaking at gun/spray

wand connection

1. Worn or torn o-ring 1. Check and replace

2. Loose hose connection 2. Tighten

Water leaking at pump 1. Loose connections 1. Tighten

2. Piston packings worn 2. Please contact our customer service department at

1-855-504-5678 or www.campbellhausfeld.com

3. Worn or torn o-ring 3. Please contact our customer service department at

1-855-504-5678 or www.campbellhausfeld.com

4. Pump head or tubes damaged from

freezing

4. Please contact our customer service department at

1-855-504-5678 or www.campbellhausfeld.com

Pump pulsates Nozzle obstructed See Nozzle Cleaning paragraph in the Maintenance

section for the correct procedure

MAINTENANCE /

REPAIR

TROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

15

MAINTENANCE AND INSPECTION INSTRUCTIONS

Risk of burn hazard. When performing maintenance, you may be exposed to hot surfaces, water

pressure or moving parts that can cause serious injury or death.

Risk of fire hazard. Always disconnect, spark plug wire, let the engine cool and release all water

pressure before performing any maintenance or repair. The engine contains flammable fuel. Do

not smoke or work near open flames while performing maintenance.

To ensure efficient operation and longer life of your pressure washer, a routine maintenance schedule

should be prepared and followed. If the pressure washer is used in unusual conditions, such as high-

temperatures or dusty conditions, more fre quent maintenance checks will be required.

Engine

Consult the Engine Owner’s Manual for the man u fac tur er’s recommendations for any and all maintenance.

NOTE: The engine drain plug is located at the rear of the unit.

Pump

The pump was filled with oil at the factory. The pump on this unit is maintenance free and requires no oil. If

there is a problem with the pump contact us at 1-855-504-5678 or www.campbellhausfeld.com.

Connections

Connections on pressure washer hoses, gun and spray wand should be cleaned regularly and lubricated with

light oil or lithium grease to prevent leakage and damage to the o-rings.

Nozzle Cleaning (Figure 22)

If the nozzle becomes clogged with foreign materials, such as dirt, excessive pressure may develop. If

the nozzle becomes partially clogged or restricted, the pump pressure will pulsate. Clean the nozzle

immediately using the nozzle kit supplied and the following instructions:

1. Shut off the pressure washer and turn off the water supply.

2. Pull trigger on gun handle to relieve any water pressure.

3. Disconnect the spray wand from the gun.

4. Remove any obstructions with the nozzle cleaning tool provided and backflush with

clean water.

5. Direct water supply (N) into nozzle to backflush loosened particles for 30 seconds.

6. Reconnect spray wand to gun and turn on water supply.

7. Start pressure washer and place spray wand into high pressure setting to test.

Clean The Water Inlet Filter (Fig. 8)

This screen filter should be checked periodically and cleaned if necessary.

1. Remove filter by grasping end and removing it from water inlet of pump.

2. Clean filter by flushing it with water on both sides.

3. Re-insert filter into water inlet of pump. NOTE: Convex side faces out.

NOTE: Do not operate the pressure washer without filter properly installed.

MAINTENANCE /

REPAIR TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS GETTING STARTED

16

N

Figure 22

MAINTENANCE /

REPAIR

TROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

17

STORAGE

Engine

Consult the Engine Owner’s Manual for manufacturer’s recommendations for storage.

TO PREVENT FUEL-RELATED PROBLEMS

1. Add Ethanol ShieldTM (sold separately) fuel stabilizer following the manufacturer’s instructions. When

adding a gasoline stabilizer, fill the fuel tank with fresh gasoline. If only partially filled, air in the tank

will promote fuel deterioration during storage. If you keep a container of gasoline for refueling, be

sure that it contains only fresh gasoline.

2. After adding a gasoline stabilizer, run the engine outdoors for 10 minutes to be sure that treated

gasoline has replaced the untreated gasoline in the carburetor.

3. Turn the fuel valve to the OFF position.

4. Continue to run the engine until it stops from the lack of fuel in the carburetor fuel bowl. Running

time should be less than 3 minutes.

Pump

The manufacturer recommends using pressure washer winterizing fluid when storing the unit for more than

30 days and/or when freezing temperatures are expected.

NOTE: Using pump guard helps provide proper lubrication to the internal seals of the pump regardless of

temperature or environment.

Risk of property damage. Use pressure washer winterizing fluid found at major retailers.

Other products could be corrosive and/or contain alcohol which may cause pump damage.

1. Turn off pressure washer and disconnect hoses from pump.

2. Unscrew bottle valve from Pump Guard bottle and remove seal.

3. Screw bottle valve back onto bottle.

4. Attach bottle to water inlet of pump.

5. Squeeze bottle to inject contents into pump.

6. With ignition switch off, simultaneously pull starter rope and squeeze bottle. Repeat until protector

fluid exits pump outlet. NOTE: This step may require two people.

Pressure Washer

1. Drain all water from high pressure hose and wrap it onto hose wrap.

2. Drain all water from the spray gun and wand by holding spray gun in a vertical position with nozzle

end pointing down and squeezing trigger. Store in gun holder.

3. Wrap up and secure detergent siphon hose so it is protected from damage.

ACCESSORIES

Risk of fluid injection. When using replacement spray wands or guns with this pressure washer,

DO NOT use a spray wand and/or spray gun/wand combination that is shorter in length than

what was provided with this pressure washer as measured from the nozzle end of the wand to the gun trigger.

The use of any other accessory not recommended for use with this tool could be hazardous. Use

only accessories rated equal to or greater than the rating of the pressure washer.

SERVICE INFORMATION

Do not return this product to your retailer. Please contact our customer service department at

1-855-504-5678 or www.campbellhausfeld.com

18

Reminder: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.

LIMITED WARRANTY

1. DURATION: From the date of purchase by the original purchaser as follows:

ENGINE AND EMISSIONS CONTROL SYSTEM: Covered by engine manufacturer warranty. See engine manual.

HIGH PRESSURE PUMP (DEFECTS IN MATERIAL AND WORKMANSHIP): One (1) year from date of purchase.

FRAME (DEFECTS IN MATERIAL AND WORKMANSHIP): One (1) year from date of purchase.

ACCESSORIES (DEFECTS IN MATERIAL AND WORKMANSHIP): Ninety (90) days from date of purchase. Includes

nozzles, hoses, spray guns, wands, tires, feet.

2. WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld a Marmon/Berkshire Hathaway Company, 100

Production Drive, Harrison, Ohio, 45030. Visit www.campbellhausfeld.com

3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the

Campbell Hausfeld pressure washer.

4. WHAT PRODUCTS ARE COVERED UNDER THIS WARRANTY: This Campbell Hausfeld Pressure Washer.

5. WHAT IS COVERED UNDER THIS WARRANTY: Substantial defects on material and workmanship which occur within

the duration of the warranty period with the exceptions noted below.

6. WHAT IS NOT COVERED UNDER THIS WARRANTY:

A. Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED

FROM THE DATE OF ORIGINAL PURCHASE AS STATED IN THE DURATION. Some states do not allow limitation on

how long an implied warranty lasts, so the above limitations may not apply to you.

B. ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY

DEFECT, FAILURE, OR MALFUNCTION OF THE CAMPBELL HAUSFELD pressure washer. Some States do not allow

the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not

apply to you.

C. Any failure that results from shipping damage, accident, purchaser’s abuse, neglect or failure to install and

operate pressure washer in accordance with instructions provided in the owner’s manual(s) supplied with

product.

D. Pre-delivery service, i.e. assembly, oil or lubricants and adjustment.

E. Items or service normally required to maintain the pressure washer.

F. Additional items not covered under the warranty:

1. Normal wear items such as high pressure hoses, water and oil seals, o-rings, valves, lances and spray nozzles.

2. Cosmetic defects that do not interfere with functionality.

3. Rusted components.

4. Pump wear or valve damage caused by using improper oil, oil contamination or by failure to follow proper

oil maintenance guidelines.

G. Gasoline engine and components are expressly excluded from coverage under this limited warranty. Such

components should be returned by the purchaser to the original manufacturer or to its authorized repair

stations for service.

7. RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor’s option, pressure

washer or component which is defective, has malfunctioned and/or failed to conform within duration of the

warranty period.

8. RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY:

A. Provide dated proof of purchase and maintenance records.

B. Deliver or ship the Campbell Hausfeld pressure washer or component to nearest Campbell Hausfeld Authorized

Service Center. Freight costs, if any, must be borne by the purchaser.

C. Use reasonable care in the operation and maintenance of the pressure washer as described in the owner’s

manual(s).

9. WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY: Repair or replacement

will be scheduled and serviced according to the normal work flow at the servicing location, and depending on the

availability of replacement parts.

This Limited Warranty applies in the U.S., Canada and Mexico only and gives you specific legal rights. You may also have

other rights which vary from state to state or country to country.

La page est en cours de chargement...

Campbell Hausfeld PW320200 Mode d'emploi

Campbell Hausfeld PW320200 Mode d'emploi

dans d''autres langues