INSTALLATION INSTRUCTIONS
FCA501
FCA502
FCA503
Upper Accessory Shelf
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
FCA501 / 502 / 503
FCA501 / 502 / 503 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components
placed on the FCA501/FCA502/FCA503 does
not exceed 10 lbs (4.5 kg).
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
WARNING: RISK OF INJURY TO PERSONS! Do not use
this mounting system to support video equipment such as
televisions or computer monitors.
--SAVE THESE INSTRUCTIONS--
DIMENSIONS
OF MOUNT
L
18.8
476.8
MAXIMUM EXTENSION
FCA501
Installation Instructions FCA501 / 502 / 503
3
DIMENSIONS - continued
L
OF MOUNT
18.8
476.8
MAXIMUM EXTENSION
FCA502
L
OF MOUNT
FCA503
FCA501 / 502 / 503 Installation Instructions
4
LEGEND
TOOLS REQUIRED FOR INSTALLATION
PARTS
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
#2
3/8"
A (1)
[Shelf - FCA503]
A (1)
[Shelf - FCA502]
A (1)
[Shelf - FCA501]
B (1)
[Retaining bracket]
C (1)
[Upright] D (4)
10-24
E (1)
1/4-20 x 3/8"
F (3)
1/4-20 x 1/2"
Installation Instructions FCA501 / 502 / 503
5
ASSEMBLY AND INSTALLATION
Assembling Shelf to Upright
1. Attach shelf (A) to upright (C) using three 1/4-20 x 1/2"
Phillips pan head machine screws (F). (See Figure 1)
Figure 1
Attaching Shelf Assembly to Mount
1. Lower shelf assembly onto mount extrusion, placing shelf
assembly hooks over extrusion. (See Figure 2)
Figure 2
2. Attach retaining bracket (B) to upright, pressing retaining
bracket against mount extrusion and tightening, using four
10-24 lock nuts (D). (See Figure 3)
Figure 3
1
(FCA503 shown)
(F) x 3
(A)
(C)
1
Extrusion
Shelf assembly
(FAC503 shown)
(B)
2
(D) x 4
Mount
extrusion
(FAC503 shown)
FCA501 / 502 / 503 Installation Instructions
6
Adjustments
1. Loosen two screws on each side of upright. (See Figure 4)
2. Adjust height of shelf, as necessary.
3. Tighten two screws on each side of upright.
Figure 4
Installing Components
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located on the
FCA501/FCA502/FCA503
does not exceed 10 lbs (4.5 kg)
.
NOTE: OPTIONAL: Slots are provided in shelf for strap (not
included) to hold component in place. (See Figure 5)
Installing Camera
1. Install 1/4-20 x 3/8" Phillips pan machine screw (E) through
mounting slot on shelf and into hole on bottom of camera
(not included). (See Figure 5)
2. Route cable from camera towards back of shelf and down
behind the FCA501/502/503. (See Figure 5)
Figure 5
1
2
2
3
(FAC503 shown)
(mount extrusion not shown for clarity)
(FAC501 shown)
Slots provided
for strap
(not included)
1
(E) x 1
Camera
(example -
2
not included)
Installation Instructions FCA501 / 502 / 503
7
FCA501 / 502 / 503 Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P 800.582.6480 / 952.225.6000
F 877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P +31 (0) 495 580 852
F +31 (0) 495 580 845
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099
F 852 2145 4477
Chief Manufacturing, a products division
of Milestone AV Technologies
8800-002260 Rev00
2012 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
11/12
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Chief FCA501 Guide d'installation
- Catégorie
- Mur
- Taper
- Guide d'installation
dans d''autres langues
- English: Chief FCA501 Installation guide
Documents connexes
-
Chief FCA535 Guide d'installation
-
-
-
-
-
-
-
Chief PACCS1 Guide d'installation
-
-