LG 32LB550U Manuel utilisateur

Please read this manual carefully before operating your

set and retain it for future reference.

OWNER’S MANUAL

Safety and Reference

*MFL68003811*

www.lg.com

P/NO : MFL68003811 (1411-REV00)

Printed in Korea

2

ENGLISH

SAFETY INSTRUCTIONS

Please read these safety precautions carefully before

using the product.

WARNING

Do not place the TV and/or remote control in the following

environments:

t A location exposed to direct sunlight

t An area with high humidity such as a bathroom

t Near any heat source such as stoves and other devices that

produce heat

t Near kitchen counters or humidiers where they can easily be

exposed to steam or oil

t An area exposed to rain or wind

t Near containers of water such as vases

Otherwise, this may result in re, electric shock, malfunction or product

deformation.

Do not place the product where it might be exposed to dust. This may

cause a re hazard.

Mains Plug is the TV connecting/disconnecting device to AC mains

electric supply.This plug must remain readily attached and operable

when TV is in use.

Do not touch the power plug with wet hands. Additionally, if the cord

pin is wet or covered with dust, dry the power plug completely or wipe

dust o. You may be electrocuted due to excess moisture.

Make sure to connect Mains cable to compliant AC mains socket with

Grounded earth pin. (Except for devices which are not grounded on

earth.) Otherwise possibility you may be electrocuted or injured.

Insert power cable plug completely into wall socket otherwise if not

secured completely into socket, re ignition may break out.

Ensure the power cord does not come into contact with hot objects

such as a heater. This may cause a re or an electric shock hazard.

Do not place a heavy object, or the product itself, on power cables.

Otherwise, this may result in re or electric shock.

Bend antenna cable between inside and outside building to prevent

rain from owing in. This may cause water damaged inside the Product

and could give an electric shock.

When mounting TV onto wall make sure to neatly install and isolate

cabling from rear of TV as to not create possibility of electric shock /

re hazard.

Do not plug too many electrical devices into a single multiple electrical

outlet. Otherwise, this may result in re due to over-heating.

Do not drop the product or let it fall over when connecting external

devices. Otherwise, this may result in injury or damage to the product.

ENGLISH

3

Desiccant

Keep the anti-moisture packing material or vinyl packing out of the

reach of children. Anti-moisture material is harmful if swallowed. If

swallowed by mistake, force the patient to vomit and visit the nearest

hospital. Additionally, vinyl packing can cause suocation. Keep it out

of the reach of children.

Do not let your children climb or cling onto the TV.

Otherwise, the TV may fall over, which may cause serious injury.

Dispose of used batteries carefully to ensure that a small child does not

consume them. Please seek Doctor- Medical Attention immediately if

child consumes batteries.

Do not insert any metal objects/conductors (like a metal chopstick/

cutlery/screwdriver) between power cable plug and input Wall Socket

while it is connected to the input terminal on the wall. Additionally,

do not touch the power cable right after plugging into the wall input

terminal. You may be electrocuted. (Depending on model)

Do not put or store inammable substances near the product. There is a

danger of combustion/explosion or re due to careless handling of the

inammable substances.

Do not drop metallic objects such as coins, hair pins, chopsticks or wire

into the product, or inammable objects such as paper and matches.

Children must pay particular attention. Electrical shock, re or injury

can occur. If a foreign object is dropped into the product, unplug the

power cord and contact the service centre.

Do not spray water on the product or scrub with an inammable

substance (thinner or benzene). Fire or electric shock accident can

occur.

Do not allow any impact, shock or any objects to fall into the unit,

and do not drop anything onto the screen. You may be injured or the

product can be damaged.

Never touch this product or antenna during a thunder or lighting storm.

You may be electrocuted.

Never touch the wall outlet when there is leakage of gas, open the

windows and ventilate. It may cause a re or a burn by a spark.

Do not disassemble, repair or modify the product at your own

discretion. Fire or electric shock accident can occur.

Contact the service centre for check, calibration or repair.

If any of the following occur, unplug the product immediately and

contact your local service centre.

t The product has been impacted by shock

t The product has been damaged

t Foreign objects have entered the product

t The product produced smoke or a strange smell

This may result in re or electric shock.

4

ENGLISH

Unplug the TV from AC mains wall socket if you do not intend to use the

TV for a long period of time. Accumulated dust can cause re hazard

and insulation deterioration can cause electric leakage/shock/re.

Apparatus shall not be exposed to dripping or splashing and no objects

lled with liquids, such as vases, shall be placed on the apparatus.

Do not install this product on a wall if it could be exposed to oil or oil

mist. This may damage the product and cause it to fall.

CAUTION

Install the product where no radio wave occurs.

There should be enough distance between an outside antenna and

power lines to keep the former from touching the latter even when the

antenna falls. This may cause an electric shock.

Do not install the product on places such as unstable shelves or inclined

surfaces. Also avoid places where there is vibration or where the

product cannot be fully supported. Otherwise, the product may fall or

ip over, which may cause injury or damage to the product.

If you install the TV on a stand, you need to take actions to prevent the

product from overturning. Otherwise, the product may fall over, which

may cause injury.

If you intend to mount the product to a wall, attach VESA standard

mounting interface (optional parts) to the back of the product. When

you install the set to use the wall mounting bracket (optional parts), x

it carefully so as not to drop.

Only use the attachments / accessories specied by the manufacturer.

When installing the antenna, consult with a qualied service

technician. If not installed by a qualied technician, this may create a

re hazard or an electric shock hazard.

We recommend that you maintain a distance of at least 2 to 7 times

the diagonal screen size when watching TV. If you watch TV for a long

period of time, this may cause blurred vision.

Only use the specied type of battery. This could cause damage to the

remote control.

Do not mix new batteries with old batteries. This may cause the

batteries to overheat and leak.

Batteries should not be exposed to excessive heat. For example, keep

away from direct Sunlight , open replace and electric heaters .

Do not place non-rechargeable batteries in charging device.

Make sure there are no objects between the remote control and its

sensor.

Signal from Remote Control can be interrupted due to external/internal

lighting eg Sunlight, uorescent lighting. If this occurs turn o lighting

or darken viewing area.

ENGLISH

5

When connecting external devices such as video game consoles, make

sure the connecting cables are long enough. Otherwise, the product

may fall over, which may cause injury or damage the product.

Do not turn the product On/O by plugging-in or unplugging the power

plug to the wall outlet. (Do not use the power plug for switch.) It may

cause mechanical failure or could give an electric shock.

Please follow the installation instructions below to prevent the product

from overheating.

t The distance between the product and the wall should be more

than 10cm.

t Do not install the product in a place with no ventilation (e.g., on a

bookshelf or in a cupboard).

t Do not install the product on a carpet or cushion.

t Make sure the air vent is not blocked by a tablecloth or curtain.

Otherwise, this may result in re.

Take care not to touch the ventilation openings when watching the TV

for long periods as the ventilation openings may become hot. This does

not aect the operation or performance of the product.

Periodically examine the cord of your appliance, and if its appearance

indicates damage or deterioration, unplug it, discontinue use of the

appliance, and have the cord replaced with an exact replacement part

by an authorized servicer.

Prevent dust collecting on the power plug pins or outlet. This may cause

a re hazard.

Protect the power cord from physical or mechanical abuse, such as

being twisted, kinked, pinched, closed in a door, or walked upon. Pay

particular attention to plugs, wall outlets, and the point where the cord

exits the appliance.

Do not press strongly upon the panel with a hand or sharp object such

as nail, pencil or pen, or make a scratch on it, as it may causedamage

to screen.

Avoid touching the screen or holding your nger(s) against it for long

periods of time. Doing so may produce some temporary or permanent

distortion/damage to screen.

When cleaning the product and its components, unplug the power

rst and wipe it with a soft cloth. Applying excessive force may cause

scratches or discolouration. Do not spray with water or wipe with a wet

cloth. Never use glass cleaner, car or industrial shiner, abrasives or wax,

benzene, alcohol etc., which can damage the product and its panel.

Otherwise, this may result in re, electric shock or product damage

(deformation, corrosion or breakage).

As long as this unit is connected to the AC wall outlet, it is not

disconnected from the AC power source even if you turn o this unit

by SWITCH.

When unplugging the cable, grab the plug and unplug it, by pulling

at the plug. Don’t pull at the cord to unplug the power cord from the

power board, as this could be hazardous.

6

ENGLISH

When moving the product, make sure you turn the power o rst. Then,

unplug the power cables, antenna cables and all connecting cables.

The TV set or power cord may be damaged, which may create a re

hazard or cause electric shock.

When moving or unpacking the product, work in pairs because the

product is heavy. Otherwise, this may result in injury.

Contact the service centre once a year to clean the internal parts of the

product.

Accumulated dust can cause mechanical failure.

Refer all servicing to qualied service personnel. Servicing is required

when the apparatus has been damaged in any way, such as power

supply cord or plug is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

If the product feels cold to the touch, there may be a small “icker”

when it is turned on. This is normal, there is nothing wrong with

product.

The panel is a high technology display product with resolution of two

million to six million pixels. You may see tiny black dots and/or brightly

coloured dots (red, blue or green) at a size of 1ppm on the panel. This

does not indicate a malfunction and does not aect the performance

and reliability of the product.

This phenomenon also occurs in third-party products and is not subject

to exchange or refund.

You may nd dierent brightness and color of the panel depending on

your viewing position(left/right/top/down).

This phenomenon occurs due to the characteristic of the panel. It is not

related with the product performance, and it is not malfunction.

* LG LED TVs are LCD TVs with LED backlighting.

Displaying a still image (e.g., broadcasting channel logo, on-screen

menu, scene from a video game) for a prolonged time may cause

damage to the screen, resulting in retention of the image, which is

known as image sticking. The warranty does not cover the product for

image sticking.

Avoid displaying a xed image on your television’s screen for a

prolonged period (2 or more hours for LCD, 1 or more hours for Plasma).

Also, if you watch the TV at a ratio of 4:3 for a long time, image sticking

may occur on the borders of the panel.

This phenomenon also occurs in third-party products and is not subject

to exchange or refund.

Generated Sound

“Cracking” noise: A cracking noise that occurs when watching or turning

o the TV is generated by plastic thermal contraction due to tempera-

ture and humidity. This noise is common for products where thermal

deformation is required. Electrical circuit humming/panel buzzing:

A low level noise is generated from a high-speed switching circuit,

which supplies a large amount of current to operate a product. It varies

depending on the product.

This generated sound does not aect the performance and reliability

of the product.

Do not use high voltage electrical goods near the TV (e.g. electric

mosquito-swatter). This may result in product malfunction.

ENGLISH

7

Viewing 3D Imaging (Only 3D

models)

WARNING

Viewing Environment

t Viewing Time

- When watching 3D contents, take 5 - 15 minute breaks every

hour. Viewing 3D contents for a long period of time may cause

headache, dizziness, fatigue or eye strain.

Those that have a photosensitive seizure or

chronic illness

t Some users may experience a seizure or other abnormal symptoms

when they are exposed to a ashing light or particular pattern

from 3D contents.

t Do not watch 3D videos if you feel nausea, are pregnant and/ or

have a chronic illness such as epilepsy, cardiac disorder, or blood

pressure disease, etc.

t 3D Contents are not recommended to those who suer from stereo

blindness or stereo anomaly. Double images or discomfort in

viewing may be experienced.

t If you have strabismus (cross-eyed), amblyopia (weak eyesight) or

astigmatism, you may have trouble sensing depth and easily feel

fatigue due to double images. It is advised to take frequent breaks

than the average adult.

t If your eyesight varies between your right and left eye, revise your

eyesight prior to watching 3D contents.

Symptoms which require discontinuation or

refraining from watching 3D contents

t Do not watch 3D contents when you feel fatigue from lack of sleep,

overwork or drinking.

t When these symptoms are experienced, stop using/watching 3D

contents and get enough rest until the symptom subsides.

- Consult your doctor when the symptoms persist. Symptoms may

include headache, eyeball pain, dizziness, nausea, palpitation,

blurriness, discomfort, double image, visual inconvenience or

fatigue.

CAUTION

Viewing Environment

t Viewing Distance

- Maintain a distance of at least twice the screen diagonal length

when watching 3D contents. If you feel discomfort in viewing 3D

contents, move further away from the TV.

Viewing Age

t Infants/Children

- Usage/ Viewing 3D contents for children under the age of 6 are

prohibited.

- Children under the age of 10 may overreact and become overly

excited because their vision is in development (for example:

trying to touch the screen or trying to jump into it. Special

monitoring and extra attention is required for children watching

3D contents.

- Children have greater binocular disparity of 3D presentations

than adults because the distance between the eyes is

shorter than that of adults. Therefore they will perceive more

stereoscopic depth compared to adults for the same 3D image.

t Teenagers

- Teenagers under the age of 19 may react with sensitivity due

to stimulation from light in 3D contents. Advise them to refrain

from watching 3D contens for a long time when they are tired.

t Elderly

- The elderly may perceive less 3D eect compared to the young.

Do not sit closer to the TV than the recommended distance.

Cautions when using the 3D glasses

t Make sure to use LG 3D glasses. Otherwise, you may not be able to

view 3D videos properly.

t Do not use 3D glasses instead of your normal glasses, sunglasses or

protective goggles.

t Using modied 3D glasses may cause eye strain or image

distortion.

t Do not keep your 3D glasses in extremely high or low

temperatures. It will cause deformation.

t The 3D glasses are fragile and are easily scratched. Always use a

soft, clean piece of cloth when wiping the lenses. Do not scratch

the lenses of the 3D glasses with sharp objects or clean/wipe them

with chemicals.

8

ENGLISH

PREPARING

NOTE

t Image shown may dier from your TV.

t Your TV’s OSD (On Screen Display) may dier slightly from that

shown in this manual.

t The available menus and options may dier from the input source

or product model that you are using.

t New features may be added to this TV in the future.

t The TV can be placed in standby mode in order to reduce the power

consumption. And the TV should be turned o if it will not be

watched for some time, as this will reduce energy consumption.

t The energy consumed during use can be signicantly reduced if the

level of brightness of the picture is reduced, and this will reduce

the overall running cost.

t The items supplied with your product may vary depending on the

model.

t Product specications or contents of this manual may be changed

without prior notice due to upgrade of product functions.

t For an optimal connection, HDMI cables and USB devices should

have bezels less than 10 mm thick and 18 mm width. Use an

extension cable that supports USB 2.0 if the USB cable or USB

memory stick does not t into your TV’s USB port.

A

B

A

B

*A

<

=

10 mm

*B

<

=

18 mm

t Use a certied cable with the HDMI logo attached.

t If you do not use a certied HDMI cable, the screen may not display

or a connection error may occur. (Recommended HDMI cable types)

- High-Speed HDMI®/™ cable

- High-Speed HDMI®/™ cable with Ethernet

CAUTION

t Do not use any unapproved items to ensure the safety and product

life span.

t Any damage or injuries caused by using unapproved items are not

covered by the warranty.

t Some models have a thin lm attached on to the screen and this

must not be removed.

SEPARATE PURCHASE

Separate purchase items can be changed or modied for quality

improvement without any notication. Contact your dealer to buy

these items. These devices only work with certain models. The model

name or design may be changed depending on the upgrade of product

functions, manufacturer’s circumstances or policies.

(Depending on model)

AG-F***

Cinema 3D glasses

AG-F***DP

Dual play glasses

LG Audio Device

MAINTENANCE

Cleaning your TV

Clean your TV regularly to keep the best performance and to extend the

product lifespan.

t Make sure to turn the power o and disconnect the power cord and

all other cables rst.

t When the TV is left unattended and unused for a long time,

disconnect the power cord from the wall outlet to prevent possible

damage from lightning or power surges.

Screen, frame, cabinet and stand

To remove dust or light dirt, wipe the surface with a dry, clean, and

soft cloth.

To remove major dirt, wipe the surface with a soft cloth dampened in

clean water or a diluted mild detergent. Then wipe immediately with

a dry cloth.

t Avoid touching the screen at all times, as this may result in damage

to the screen.

t Do not push, rub, or hit the screen surface with your ngernail or a

sharp object, as this may result in scratches and image distortions.

t Do not use any chemicals as this may damage the product.

t Do not spray liquid onto the surface. If water enters the TV, it may

result in re, electric shock, or malfunction.

Power cord

Remove the accumulated dust or dirt on the power cord regularly.

ENGLISH

9

LIFTING AND MOVING THE TV

Please note the following advice to prevent the TV from being scratched

or damaged and for safe transportation regardless of its type and size.

t It is recommended to move the TV in the box or packing material

that the TV originally came in.

t Before moving or lifting the TV, disconnect the power cord and

all cables.

t When holding the TV, the screen should face away from you to

avoid damage.

t Hold the top and bottom of the TV frame rmly. Make sure not to

hold the transparent part, speaker, or speaker grill area.

t When transporting a large TV, there should be at least 2 people.

t When transporting the TV by hand, hold the TV as shown in the

following illustration.

t When transporting the TV, do not expose the TV to jolts or

excessive vibration.

t When transporting the TV, keep the TV upright, never turn the TV

on its side or tilt towards the left or right.

t Do not apply excessive pressure to cause exing /bending of frame

chassis as it may damage screen.

CAUTION

t Avoid touching the screen at all times, as this may result in damage

to the screen.

USING THE JOYSTICK BUTTON

You can simply operate the TV functions, pressing or moving the joystick

button up, down, left or right.

Joystick Button

Basic Functions

Power On

When the TV is turned o, place your

nger on the joystick button and

press it once and release it.

Power O

When the TV is turned on, place your

nger on the joystick button and

press it once for a few seconds and

release it. (However, if the Menu

button is on the screen, pressing and

holding the joystick button will let

you exit the Menu.)

Volume

Control

If you place your nger over the

joystick button and move it left or

right, you can adjust the volume level

you want.

Programmes

Control

If you place your nger over the

joystick button and move it up or

down, you can scrolls through the

saved programmes you want.

Adjusting the Menu

When the TV is turned on, press the joystick button one time. You can

adjust the Menu items moving the joystick button up, down, left or

right.

Turns the power o.

Clears on-screen displays and returns to TV viewing.

Changes the input source.

Accesses the main menu.

NOTE

t When your nger over the joystick button and push it to the up,

down, left or right, be careful not to press the joystick button. If you

press the joystick button rst, you may not be able to adjust the

volume level and saved programmes.

10

ENGLISH

MOUNTING ON A TABLE

1 Lift and tilt the TV into its upright position on a table.

t Leave a 10 cm (minimum) space from the wall for proper

ventilation.

10 cm

2 Connect the power cord to a wall outlet.

CAUTION

t Do not place the TV near or on sources of heat, as this may result in

re or other damage.

Securing the TV to a wall

(This feature is not available for all models.)

1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back

of the TV.

t If there are bolts inserted at the eye-bolts position, remove the

bolts rst.

2 Mount the wall brackets with the bolts to the wall.

Match the location of the wall bracket and the eye-bolts on the rear

of the TV.

3 Connect the eye-bolts and wall brackets tightly with a sturdy rope.

Make sure to keep the rope horizontal with the at surface.

CAUTION

t Make sure that children do not climb on or hang on the TV.

NOTE

t Use a platform or cabinet that is strong and large enough to

support the TV securely.

t Brackets, bolts and ropes are not provided. You can obtain

additional accessories from your local dealer.

MOUNTING ON A WALL

Attach an optional wall mount bracket at the rear of the TV carefully

and install the wall mount bracket on a solid wall perpendicular to

the oor. When you attach the TV to other building materials, please

contact qualied personnel. LG recommends that wall mounting be

performed by a qualied professional installer. We recommend the

use of LG’s wall mount bracket. When you do not use LG’s wall mount

bracket, please use a wall mount bracket where the device is adequately

secured to the wall with enough space to allow connectivity to external

devices.

10 cm

Make sure to use screws and wall mount bracket that meet the VESA

standard. Standard dimensions for the wall mount kits are described in

the following table.

Separate purchase(Wall Mounting Bracket)

Model

32/39LB56**

32LB55**

32LB62**

42/47/50/55LB56**

42/49LB55**

42/49/55LB62**

VESA (A x B) 200 x 200 400 x 400

Standard screw M6 M6

Number of screws 4 4

Wall mount

bracket

LSW240B

MSW240

LSW440B

MSW240

Model 60LB56**

VESA (A x B) 400 x 400

Standard screw M6

Number of screws 4

Wall mount

bracket

LSW440B

ENGLISH

11

A

B

CAUTION

t Disconnect the power rst, and then move or install the TV.

Otherwise electric shock may occur.

t If you install the TV on a ceiling or slanted wall, it may fall and

result in severe injury. Use an authorised LG wall mount and

contact the local dealer or qualied personnel.

t Do not over tighten the screws as this may cause damage to the TV

and void your warranty.

t Use the screws and wall mounts that meet the VESA standard. Any

damages or injuries by misuse or using an improper accessory are

not covered by the warranty.

NOTE

t Use the screws that are listed on the VESA standard screw

specications.

t The wall mount kit includes an installation manual and necessary

parts.

t The wall mount bracket is not provided. You can obtain additional

accessories from your local dealer.

t The length of screws may dier depending on the wall mount.

Make sure to use the proper length.

t For more information, refer to the manual supplied with the wall

mount.

t When attaching a wall mounting bracket to the TV, insert the wall

mount spacers into the TV wall mount holes to adjust the vertical

angle of the TV. (Only when the item of the following form is

provided)

Provided Item

Wall Mount Spacer

CONNECTIONS

NOTIFICATIONS

Connect various external devices to the TV and switch input modes to

select an external device. For more information of external device’s

connection, refer to the manual provided with each device.

Available external devices are: HD receivers, DVD players, VCRs, audio

systems, USB storage devices, PC, gaming devices, and other external

devices.

NOTE

t The external device connection may dier from the model.

t Connect external devices to the TV regardless of the order of the

TV port.

t If you record a TV program on a DVD recorder or VCR, make sure to

connect the TV signal input cable to the TV through a DVD recorder

or VCR. For more information of recording, refer to the manual

provided with the connected device.

t Refer to the external equipment’s manual for operating

instructions.

t If you connect a gaming device to the TV, use the cable supplied

with the gaming device.

t In PC mode, there may be noise associated with the resolution,

vertical pattern, contrast or brightness. If noise is present, change

the PC output to another resolution, change the refresh rate to

another rate or adjust the brightness and contrast on the PICTURE

menu until the picture is clear.

t In PC mode, some resolution settings may not work properly

depending on the graphics card.

Antenna connection

Connect the TV to a wall antenna socket with an RF cable (75 Ω).

t Use a signal splitter to use more than 2 TVs.

t If the image quality is poor, install a signal amplier properly to

improve the image quality.

t If the image quality is poor with an antenna connected, try to

realign the antenna in the correct direction.

t An antenna cable and converter are not supplied.

t Supported DTV Audio: MPEG, Dolby Digital, Dolby Digital Plus,

HE-AAC

Satellite dish connection

(Only satellite models)

Connect the TV to a satellite dish to a satellite socket with a satellite RF

cable (75 Ω).

12

ENGLISH

Euro scart connection

Transmits the video and audio signals from an external device to the

TV set. Connect the external device and the TV set with the euro scart

cable as shown.

Output

Type

Current

input mode

AV1

(TV Out1)

Digital TV Digital TV

Analogue TV, AV

Analogue TVComponent

HDMI

1 TV Out : Outputs Analogue TV or Digital TV signals.

t Any Euro scart cable used must be signal shielded.

t When watching digital TV in 3D imaging mode, only 2D out signals

can be output through the SCART cable. (Only 3D models)

REMOTE CONTROL

(Depending on model)

The descriptions in this manual are based on the buttons on the remote

control. Please read this manual carefully and use the TV correctly.

To replace batteries, open the battery cover, replace batteries (1.5

V AAA) matching the

and ends to the label inside the

compartment, and close the battery cover. To remove the batteries,

perform the installation actions in reverse.

CAUTION

t Do not mix old and new batteries, as this may damage the remote

control.

Make sure to point the remote control toward the remote control sensor

on the TV.

1

4 5 6

7 8 9

LIST

SUBTITLE

Q.VIEW

P

0

FAV

MUTE

2 3

INPUT

TV/

RAD

PAGE

A

1 2

3

B

A

(POWER) Turns the TV on or o.

Selects Radio, TV and DTV programme.

Recalls your preferred subtitle in digital mode.

1

By Pressing AD button, audio descriptions function will be

enabled. (Depending on model)

1

Shows programme guide. (Depending on model)

2

Resizes an image. (Depending on model)

2

Selects an AV mode. (Depending on model)

Changes the input source.

Number buttons Enters numbers.

Accesses the saved programme list.

Returns to the previously viewed programme.

B

Accesses your favourite programme list.

3

Shows programme guide. (Depending on model)

3

Used for viewing 3D video. (Depending on model)

Mutes all sounds.

Adjusts the volume level.

 Scrolls through the saved programmes.

 Moves to the previous or next screen.

ENGLISH

13

TEXT

SETTINGS

Q.MENU

EXIT

INFO

T.OPT

4

C

D

C

Teletext buttons ( ) These buttons are used for

teletext.

Views the information of the current programme and

screen.

Accesses the main menus.

Accesses the Quick menus.

Navigation buttons (up/down/left/right) Scrolls through menus

or options.

Selects menus or options and conrms your input.

Returns to the previous level.

Clears on-screen displays and returns to TV viewing.

D

4

Selects an AV mode. (Depending on model)

4

By Pressing AD button, audio descriptions function will be

enabled. (Depending on model)

Starts to record and displays record menu.

(Only Time Machine

Ready

supported model)

Control buttons ( ) Controls the Premium

contents, Time Machine

Ready

or SmartShare menus or the SIMPLINK

compatible devices (USB or SIMPLINK or Time Machine

Ready

).

Coloured buttons These access special functions in some menus.

( : Red, : Green, : Yellow, : Blue)

LICENSES

Supported licenses may dier by model. For more information about

licenses, visit www.lg.com.

Manufactured under license from Dolby Laboratories.

Dolby and the double-D symbol are trademarks of Dolby

Laboratories.

The terms HDMI and HDMI High-Denition Multimedia Interface,

and the HDMI logo are trademarks or registered trademarks of HDMI

Licensing LLC in the United States and other countries.

ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX,

LLC, a subsidiary of Rovi Corporation. This is an ocial DivX Certied®

device that has passed rigorous testing to verify that it plays DivX

video. Visit divx.com

for more information and software tools to convert your les into

DivX videos.

ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certied® device must be

registered in order to play purchased DivX Video-on-Demand (VOD)

movies.

To obtain your registration code, locate the DivX VOD section in your

device setup menu. Go to vod.divx.com for more information on how

to complete your registration.

“DivX Certied® to play DivX® video up to HD 1080p, including

premium content.”

“DivX®, DivX Certied® and associated logos are trademarks of Rovi

Corporation or its subsidiaries and are used under license.”

“Covered by one or more of the following U.S. patents :

7,295,673; 7,460,668; 7,515,710; 7,519,274”

14

ENGLISH

OPEN SOURCE SOFTWARE

NOTICE

To obtain the source code under GPL, LGPL, MPL and other open source

licenses, that is contained in this product, please visit http://opensource.

lge.com.

In addition to the source code, all referred license terms, warranty

disclaimers and copyright notices are available for download.

LG Electronics will also provide open source code to you on CD-ROM

for a charge covering the cost of performing such distribution (such

as the cost of media, shipping and handling) upon email request to

opensour[email protected]om. This oer is valid for three (3) years from the date

on which you purchased the product.

SETTINGS

Automatically Setting Up Programme

SETTINGS

SETUP Auto Tuning

Automatically tunes the programmes.

t If Input Source is not connected properly, programme registration

may not work.

t

Auto Tuning only nds programmes that are currently

broadcasting.

t If

Lock System is turned on, a pop-up window will appear asking

for password.

To adjust picture with Picture Wizard

SETTINGS

PICTURE Picture Wizard III

[Depending on model]

Calibrates and adjusts for optimum picture quality using the remote

control and the Picture Wizard without expensive pattern devices or

help from a specialist.

To select Picture Mode

SETTINGS

PICTURE Picture Mode

Select the picture mode optimized for the viewing environment or the

programme.

t

Vivid : Heightens contrast, brightness and sharpness to display

vivid images.

t Standard : Displays images in standard levels of contrast,

brightness and sharpness.

t Eco/APS : [Depending on model]

The Energy Saver feature changes settings on the TV to reduce

power consumption.

t Cinema/Game : Displays the optimum picture for movie, game.

t Sports : Optimizes the video image for high and dynamic actions

by emphasizing primary colours such as white, grass, or sky blue.

t Expert 1, 2 : Menu for adjusting picture quality that

allows experts and amateurs to enjoy the best TV viewing. This

is the adjustment menu provided for ISF-certied picture tuning

professionals. (ISF logo can only be used on ISF-certied TVs.)

ISFccc: Imaging Science Foundation Certied Calibration Control

t Depending on input signal, available range of picture modes may

dier.

t Expert mode is for picture tuning professionals to control

and ne-tune using a specic image. For normal images, the

eects may not be dramatic.

t The ISF function is only available on some models.

To set advanced control

SETTINGS

PICTURE Picture Mode Advanced Control /

Expert Control

Calibrates the screen for each picture mode; or adjusts picture settings

for a special screen. First select a Picture Mode of your choice.

t Dynamic Contrast : Adjusts the contrast to the optimal level

according to the brightness of the image.

t Dynamic Colour : Adjusts colours to make the image appear in

more natural colours.

t Skin Colour : Sets Skin colour spectrum separately to implement

the skin colour as dened by the user.

t Sky Colour : Sky colour is set separately.

t Grass Colour : Natural colour spectrum (meadows, hills, etc.) can

be separately set.

t Gamma : Sets the gradation curve according to the output of

picture signal in relation to the input signal.

t Colour Gamut : Selects the range of colours that can be

expressed.

t Edge Enhancer : Shows clearer and distinctive yet natural edges

of the video.

t Expert Pattern : [Depending on model]

Patterns used for expert adjustment.

t Colour Filter : Filters a specic colour spectrum in RGB colours to

ne-tune colour saturation and hue accurately.

t Colour Temperature : Adjusts the overall tone of the screen

as desired. In Expert mode, detailed ne-tuning can be set via

Gamma method, etc.

t

Colour Management System : This is a system that experts use

when they adjust colour with a test pattern. They can select from

six colour areas (Red / Green / Blue / Cyan / Magenta / Yellow)

without aecting other colours. For normal images, adjustments

may not result in noticeable colour changes.

t Depending on input signal or other picture settings, the range of

detailed items for adjustment may dier.

ENGLISH

15

To set additional picture options

SETTINGS PICTURE Picture Mode Picture Option

[Depending on model]

Adjusts detailed setting for images.

t Noise Reduction : Eliminates noise in the picture.

t MPEG Noise Reduction : Eliminates noise generated while

creating digital picture signals.

t Black Level : Adjusts the brightness and contrast of the screen

to suit the black level of the input picture by using the blackness

(black level) of the screen.

t Real Cinema : Optimizes the screen for movie viewing.

t Motion Eye Care / SUPER Energy Saving : [Depending on

model] Saves power consumption by adjusting the brightness

corresponding to the movement of the image on the screen.

t Depending on input signal or other picture settings, the range of

detailed items for adjustment may dier.

To use TruMotion

SETTINGS

PICTURE TruMotion

[Depending on model]

Corrects images to display smoother motion sequences.

t Smooth : De-judder/De-blur working on higher range in auto

mode.

t

Clear : De-judder/De-blur working on middle range in auto mode.

t User : De-judder / De-blur can be set manually.

De-judder : This function adjusts juddering of the screen.

De-blur : This function adjusts and eliminates blurring of the

screen.

Auto means Juddering and blurring range that depend on input video

status is controlled by TruMotion mode.

To use Energy Saving feature

SETTINGS

PICTURE Energy Saving

Reduces power consumption by adjusting screen brightness.

t

Auto : [Depending on model]

The TV sensor detects the ambient lighting and automatically

adjusts the screen brightness.

t

Off : Turns o the Energy Saving mode.

t Minimum / Medium / Maximum : Applies the pre-set Energy

Saving mode.

t Screen Off : Screen is turned o and only sound is played. Press

any button except Power button on the remote control to turn the

screen back on.

To use TV speaker

SETTINGS

AUDIO Sound Out TV Speaker

[Depending on model]

Sound is output through the TV speaker.

To use External Speaker

SETTINGS AUDIO Sound Out External Speaker (Optical)

[Depending on model]

Sound is output through the speaker connected to the optical port.

t SimpLink is supported.

To use Digital Sound Out

SETTINGS AUDIO Sound Out External Speaker (Optical)

Digital Sound Out

[Depending on model]

Sets up Digital Sound Out.

Item Audio Input Digital Audio Ouput

Auto

MPEG

Dolby Digital

Dolby Digital Plus

HE-AAC

PCM

Dolby Digital

PCM All PCM

To connect and use LG audio device

SETTINGS AUDIO Sound Out LG Sound Sync (Optical)

[Depending on model]

Connect LG audio device with the

logo to the optical digital

audio output port. LG audio device allows you to enjoy rich powerful

sound easily.

To use Headphone

SETTINGS AUDIO Sound Out Headphone

[Depending on model]

Sound is output through the headphone connected to the earphone/

headphone port.

To synchronize audio and video

SETTINGS AUDIO AV Sync. Adjust

[Depending on model]

Synchronizes video and audio directly when they do not match.

t If you set AV Sync. Adjust to ON, you can adjust the sound output

(TV speakers or SPDIF) to the screen image.

16

ENGLISH

To use SIMPLINK

[Depending on model]

SIMPLINK is a feature that enables you to control and manage various

multimedia devices conveniently via the SIMPLINK menu.

1 Connect the TV’s HDMI IN terminal and the SIMPLINK device’s HDMI

output terminal using an HDMI cable.

t [Depending on model]

For home theatre units with a SIMPLINK function, connect HDMI

terminals as above, and use an optical cable to connect Optical

Digital Audio Out from the TV to Optical Digital Audio In of the

SIMPLINK device.

2 Select

INPUT(OPTION) SIMPLINK.

SIMPLINK menu window appears.

3 In SIMPLINK Setting window, set SIMPLINK function to

ON.

4 In SIMPLINK menu window, selects the device you want to control.

t This function is only compatible with devices with the SIMPLINK

logo.

t To use the SIMPLINK function, you need to use a high-speed HDMI®

cable (with CEC (Consumer Electronics Control) feature added).

High-speed HDMI® cables have the No. 13 pin connected for

information exchange between devices.

t If you switch to another input, the SIMPLINK device will stop.

t If a third-party device with the HDMI-CEC function is also used, the

SIMPLINK device may not work normally.

t [Depending on model]

If you select or play media from a the device with a home theatre

function, the

HT Speaker(Speaker) is automatically connected.

Be sure to connect with an optical cable (sold separately) to use the

HT Speaker(Speaker) function.

SIMPLINK function description

t

Direct Play : Plays the multimedia device on the TV instantly.

t

Select multimedia device : Selects the desired device via the

SIMPLINK menu to control it from the TV screen instantly.

t Disc playback : Manages the multimedia device with the TV

remote control.

t Power off all devices : When you power o the TV, all connected

devices are turned o.

t Sync Power on : When the equipment with SIMPLINK function

connected HDMI terminal starts to play, the TV will automatically

turn on.

t Speaker : [Depending on model]

Select speaker either on the home theatre unit or the TV.

To set password

SETTINGS LOCK Set Password

Sets or changes the TV password.

The initial password is set to ‘0000’.

When France is selected for Country, password is not ‘0000’ but ‘1234’.

When France is selected for Country, password cannot be set to ‘0000’.

To return Factory Reset

SETTINGS OPTION Factory Reset

All stored information is deleted and TV settings are reset.

The TV turns itself o and back on, and all settings are reset.

t When

Lock System is in place, a pop-up window appears and asks

for password

t Do not turn o the power during initialization.

To remove the USB device

Q.MENU USB Device

Select a USB storage device that you want to remove.

When you see a message that the USB device has been removed,

separate the device from the TV.

t Once a USB device has been selected for removal, it can no longer

be read. Remove the USB storage device and then re-connect it.

Using a USB storage device - warning

t If the USB storage device has a built-in auto recognition program or

uses its own driver, it may not work.

t Some USB storage devices may not work or may work incorrectly.

t Use only USB storage devices formatted with the Windows FAT32 or

NTFS File System.

t For external USB HDDs, it is recommended that you use devices

with a rated voltage of less than 5 V and a rated current of less than

500 mA.

t It is recommended that you use USB memory sticks of 32 GB or less

and USB HDDs of 2 TB or less.

t If a USB HDD with power-saving function does not work properly,

turn the power o and on. For more information, refer to the user

manual of the USB HDD.

t Data in the USB storage device can be damaged, so be sure to back

up important les to other devices. Data maintenance is the user’s

responsibility and the manufacturer is not responsible for data loss.

ENGLISH

17

My Media supporting le

t Maximum data transfer rate : 20 Mbps (Mega bit per second)

t External supported subtitle formats : *.srt (SubRip), *.smi (SAMI),

*.sub (SubViewer, MicroDVD, DVDsubtitleSystem, SubIdx(Vobsub)),

*.ass/*.ssa (SubStation Alpha), *.txt (TMplayer), *.psb (PowerDivX)

t Internal supported subtitle formats: XSUB (Supports internal

subtitles generated from DivX6)

Supported Video Formats

t Maximum: 1920 x 1080 @ 30p (only Motion JPEG 640 x 480 @ 30p)

t .asf, .wmv

[Video] MPEG-2, MPEG-4 Part2, DivX3.11, DivX4, DivX5, DivX6,

XViD, H.264/AVC, VC1(WMV3, WVC1), MP43

[Audio] WMA Standard, WMA9(Pro), MP3, AAC, AC3, MP3, 3D WMV

Single Stream

t .divx, .avi

[Video] MPEG-2, MPEG-4 Part2, DivX3.11, DivX4, DivX5, DivX6,

XViD, H.264/AVC [Audio] HE-AAC, LPCM, ADPCM, MPEG- 1 Layer I,

MPEG-1 Layer II, Dolby Digital, MPEG-1 Layer III (MP3)

t .ts, .trp, .tp, .mts, .m2ts

[Video] H.264/AVC, MPEG-2, AVS, VC1 [Audio] MPEG-1 Layer I,

MPEG-1 Layer II, MPEG-1 Layer III (MP3), Dolby Digital, Dolby

Digital Plus, AAC, HE-AAC

t .vob

[Video] MPEG-1, MPEG-2

[Audio] Dolby Digital, MPEG-1 Layer I, MPEG- 1 Layer II, DVD-LPCM

t .mp4, .m4v, .mov

[Video] MPEG-2, MPEG-4 Part2, DivX3.11, DivX4, DivX5, DivX6,

XVID, H.264/AVC [Audio] AAC, MPEG-1 Layer III (MP3)

t .mkv

[Video] MPEG-2, MPEG-4 Part2, DivX3.11, DivX4, DivX5, DivX6,

XVID, H.264/AVC [Audio] HE-AAC, Dolby Digital, MPEG-1 Layer III

(MP3), LPCM

t motion JPEG

[Video] MJPEG

[Audio] LPCM, ADPCM

t .mpg, .mpeg, .mpe

[Video] MPEG-1, MPEG-2

[Audio] MPEG-1 Layer I, MPEG-1 Layer II, Dolby Digital, LPCM

t dat

[Video] MPEG-1, MPEG-2

[Audio] MP2

t v

[Video] Sorenson H.263, H.264/AVC

[Audio] MP3, AAC, HE-AAC

t *rm, *rmvb

[Video] RV30, RV40

[Audio] Dolby Digital, AAC, HE-AAC, RA6(Cook)

t 3gp, 3gp2

[Video] H.264/AVC, MPEG-4 Part2

[Audio] AAC, AMR(NB/WB)

t *rm / *rmvb : Depending on model

Supported Audio Formats

t File type : mp3

[Bit rate] 32 Kbps - 320 Kbps

[Sample freq.] 16 kHz - 48 kHz

[Support] MPEG1, MPEG2, Layer2, Layer3

t File Type : AAC

[Bit rate] Free Format

[Sample freq.] 8 kHz ~ 48 kHz

[Support] ADIF, ADTS

t File Type : M4A

[Bit rate] Free Format

[Sample freq.] 8 kHz ~ 48 kHz

[Support] MPEG-4

t File Type : WMA

[Bit rate] 128 Kbps ~ 320 Kbps

[Sample freq.] 8 kHz ~ 48 kHz

[Support] WMA7, WMA8, WMA9 Standard

t File Type : WMA

[Bit rate] ~ 768 Kbps

[Channel / Sample freq.]

M0 : up to 2 Channel @ 48 kHz

(Except LBR mode),

M1 : up to 5.1 Channel @ 48 kHz,

M2 : up to 5.1 Channel @ 96 kHz

[Support] WMA 10 Pro

t File Type : OGG

[Bit rate] Free Format

[Sample freq.] ~ 48 kHz

[Support] OGG Vorvis

Supported Photo Formats

t Category : 2D (jpeg, jpg, jpe)

[Available le type] SOF0: Baseline,

SOF1 : Extend Sequential,

SOF2 : Progressive

[Photo size] Minimum : 64 x 64,

Maximum : Normal Type: 15360 (W) x 8640

(H), Progressive Type : 1920 (W) x 1440 (H)

t Category : BMP

[Photo size] Minimum : 64 x 64, Maximum :

9600 x 6400

t Category : PNG

[Available le type] Interlace, Non-Interlace

[Photo size] Minimum : 64 x 64, Maximum : Interlace : 1200 x 800,

Non-Interlace : 9600 x 6400

t BMP and PNG format les may be slower to display than JPEG.

18

ENGLISH

TO SEE WEB MANUAL

To obtain detailed User Guide information, please visit www.lg.com.

EXTERNAL CONTROL DEVICE

SETUP

To obtain the external control device setup information, please visit

www.lg.com.

TROUBLESHOOTING

Cannot control the TV with the remote control.

t Check the remote control sensor on the product and try again.

t Check if there is any obstacle between the product and the remote

control.

t Check if the batteries are still working and properly installed (

to , to ).

No image display and no sound is produced.

t Check if the product is turned on.

t Check if the power cord is connected to a wall outlet.

t Check if there is a problem in the wall outlet by connecting other

products.

The TV turns o suddenly.

t Check the power control settings. The power supply may be

interrupted.

t Check if the

Automatic Standby (Depending on model) / Sleep

Timer / Off Time is activated in the TIME settings.

t If there is no signal while the TV is on, the TV will turn o

automatically after 15 minutes of inactivity.

When connecting to the PC (HDMI), ‘No signal’ or ‘Invalid Format’ is

displayed.

t Turn the TV o/on using the remote control.

t Reconnect the HDMI cable.

t Restart the PC with the TV on.

Bitte lesen Sie dieses Handbuch aufmerksam durch,

bevor Sie Ihr Gerät zum ersten Mal verwenden und

bewahren Sie es zur späteren Verwendung auf.

BENUTZERHANDBUCH

Sicherheit & Hinweise

www.lg.com

2

DEUTSCH

SICHERHEITSHINWEISE

Bevor Sie das Produkt zum ersten Mal verwenden,

lesen Sie diese Sicherheitshinweise bitte

aufmerksam durch.

WARNUNG

Stellen Sie das TV-Gerät mit Fernsteuerung nicht in folgenden

Umgebungen auf:

t Unter direkter Sonneneinstrahlung

t In Bereichen mit hoher Luftfeuchtigkeit, wie z. B. einem

Badezimmer

t In der Nähe von Hitzequellen, wie z. B. Öfen und anderen

hitzeerzeugenden Geräten

t In der Nähe von Küchenzeilen oder Befeuchtern, wo das Gerät

leicht Dampf oder Öl ausgesetzt sein kann

t In Bereichen, die Regen oder Wind ausgesetzt sind

t In der Nähe von Behältern mit Wasser, wie z. B. Vasen

Andernfalls kann es zu Bränden, Stromschlägen, Fehlfunktionen oder

Produktverformungen kommen.

Schützen Sie das Gerät vor Staub. Es besteht Brandgefahr.

Wenn Sie das Gerät vom Stromnetz trennen möchten, müssen Sie den

Netzstecker aus der Steckdose ziehen. Dieser Stecker muss jederzeit gut

zugänglich sein.

Berühren Sie den Netzstecker nicht mit nassen Händen. Wenn die

Kontaktstifte nass oder verstaubt sind, trocknen Sie den Netzstecker

vollständig ab, bzw. befreien Sie ihn von Staub.

Feuchtigkeit erhöht die Gefahr eines tödlichen Stromschlags.

Stellen Sie sicher, dass das Stromkabel geerdet ist. (Außer bei Geräten,

die nicht geerdet sind.) Bei Nichtbeachtung besteht die Gefahr von

Verletzungen oder eines tödlichen Stromschlags.

Das Stromkabel muss vollständig in die Steckdose eingesteckt werden.

Ist das Stromkabel nicht fest in die Steckdose eingesteckt, besteht

Brandgefahr.

Das Stromkabel darf nicht mit heißen Gegenständen wie einem

Heizkörper in Berührung kommen. Andernfalls bestehen Brandgefahr

und die Gefahr von Stromschlägen.

Stellen Sie keinen schweren Gegenstand oder das Gerät Selbst, oder auf

das Stromkabel. Andernfalls kann es zu Bränden und Stromschlägen

kommen.

Platzieren Sie das Antennenkabel zwischen dem Innen- und

Außenbereich des Gebäudes so, dass kein Regen hereinießen kann.

Etwaiger Wassereintritt kann zu Schäden am Gerät und Stromschlag

führen.

Falls das TV-Gerät an der Wand montiert wird, darf es nicht an

den Strom- und Signalkabeln auf der Rückseite des TV-Gerätes

aufgehängt werden. Anderenfalls besteht die Gefahr von Bränden oder

Stromschlägen.

Schließen Sie nicht zu viele Elektrogeräte an einer einzelnen Steckdose

an. Andernfalls kann es aufgrund von Überhitzung zu Bränden

kommen.

Lassen Sie das Gerät beim Anschluss eines externen Gerätes nicht

fallen. Andernfalls können Verletzungen verursacht oder das Gerät

beschädigt werden.

La page charge ...

LG 32LB550U Manuel utilisateur

LG 32LB550U Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents