Aeg-Electrolux HD 8795 Manuel utilisateur

Catégorie
Hottes
Taper
Manuel utilisateur

Ce manuel convient également à

HD 8760 - HD 8795
User manual
Notice d'utilisation
Cooker Hood
Hotte
2
Contents
Safety warnings................................................................................ 3
Description of the Appliance ........................................................... 5
Extraction mode ................................................................................. 5
Recirculation mode............................................................................. 5
Control Panel .................................................................................... 6
Filter checking device......................................................................... 7
Maintenance and care...................................................................... 8
Cleaning the hood .............................................................................. 8
Metal grease filter............................................................................... 8
Removing the front panels.................................................................. 8
Removing the metal grease filter........................................................ 9
Charcoal filter ................................................................................... 10
Changing the light bulb..................................................................... 11
Special accessories ....................................................................... 11
Technical assistance service......................................................... 12
Technical Specifications ................................................................ 14
Mounting accessories included ........................................................ 14
Electrical connection ..................................................................... 15
Wall mounting................................................................................... 16
3
Safety warnings
When used as an extractor unit, the hood must be fitted with a
hose having preferably the same diameter as the outlet hole.
Should there already be a pipe of diameter 125 mm that ducts to
the outside through the walls or roof, it is possible to use the 150/
125 mm reduction flange provided. In this case the hood will be
slightly noisier.
Attention: The hose is not supplied and must be purchased
separately.
The distance between the cookware support surface on top of the
cooking appliance and the lowest part of the cooker hood must be
at least 30 cm for electric cookers or, where a gas hob is fitted,
if the cooker hood is the 60 cm size (HD 8760 model):
installation above a 60 cm gas hob - minimum distance 30 cm
installation above a 70 cm gas hob - minimum distance 45 cm
installation above gas hobs larger than 70 cm is not possible
if the cooker hood is the 90 cm size (HD 8795 model):
installation above a 60 cm or 70 cm gas hob - minimum distance
30 cm
installation above gas hobs larger than 70 cm - minimum distance
45 cm
If the instructions for installation for the gas hob specify a greater
distance, this must be adhered to.
Before any cleaning or maintenance operation, disconnect the
hood from the mains by removing the plug or disconnecting the
home mains switch.
The appliance is not intended for use by children or persons with
impaired physical, sensorial or mental faculties, or if lacking in
experience or know-how, unless they are under supervision or
have been trained in the use of the appliance by a person
responsible for their safety.
Children should be monitored to ensure that they do not play with
the appliance.
Never use the hood without effectively mounted grating.!
The hood must NEVER be used as a support surface unless
specifically indicated.
The premises must be sufficiently ventilated, when the kitchen
hood is used together with other gas combustion devices or other
fuels.
The suctioned air must not be conveyed into a conduit used for the
disposal of the fumes generated by appliances that combust gases
or other fuels.
4
The flaming of foods beneath the hood itself is severely prohibited.
The use of exposed flames is detrimental to the filters and may
cause a fire risk, and must therefore be avoided in all
circumstances.
Any frying must be done with care in order to make sure that the oil
does not overheat and burst into flames.
Accessible parts may become hot when used with cooking
appliances.
As regards the technical and safety measures to be adopted for
fume discharging it is important to closely follow the relations
provided by the competent authorities.
The hood must be regularly cleaned on both the inside and outside
(AT LEAST ONCE A MONTH, it is in any event necessary to
proceed in accordance with the maintenance instructions provided
in this manual)..
Failure to follow the instructions as concerns hood and filter
cleaning will lead to the risk of fires.
Do not use or leave the hood without the lamp correctly mounted
because of the possible risk of electric shocks.
We decline any responsibility for any problems, damage or fires
caused to the appliance as the result of the non-observance of the
instructions included in this manual.
This appliance is marked according to the European directive 2002/
96/EC on Waste Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly, you will help prevent
potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste
handling of this product.
The symbol on the product, or on the documents accompanying
the product, indicates that this appliance may not be treated as
household waste. Instead it should be taken to the appropriate
collection point for the recycling of electrical and electronic
equipment.
Disposal must be carried out in accordance with local environmental
regulations for waste disposal.
For more detailed information about treatment, recovery and recycling
of this product, please contact your local council, your household
waste disposal service or the shop where you purchased the product.
5
Description of the Appliance
The hood is supplied as an extractor unit and can also be used
with a recirculation mode by fitting a charcoal filter.
You will need an original charcoal filter for this function (Available
from your local Service Force Centre).
Only for HD 8760: The cooker hood is supplied ready for use as a
recirculation hood and may be used for extraction by removing the
charcoal filter which has been fitted inside the cooker hood.
Extraction mode
In this version fumes are
extracted to the outside via
a hose connected to the
coupling ring. Fig. 1.
In order to obtain the best
performance the hose
should have a diameter
equal to the outlet hole.
Should there already be a
pipe of diameter 125 mm
that ducts to the outside
through the walls, it is
possible to use the 150/125
mm reduction flange
provided. In this case the
hood will be slightly noisier.
Recirculation mode
The air is filtered through a
charcoal filter and returned to
the kitchen.
You will need an original
charcoal filter for the
recirculation mode. (See
Special Accessories).
Fix the deflector using 2 screws
Ø 3.5x9.5 mm. Fig. 2.
coupling ring
reduction
flange
Fig. 1
Deflector
Fig. 2
6
Control Panel
Best results are obtained by using a low speed for normal
conditions and a high speed when odours are more concentrated.
Turn the hood on a few minutes before you start cooking, you will
then get an under pressure in the kitchen. The hood should be left
on after cooking for about 15 minutes or until all the odours have
disappeared.
Cooker hood operation can also be controlled using the remote
control (the remote control is an accessory and may be ordered
separately).
The control panel consists of a knob and 2 LEDs; it is
located at the bottom right-hand side of the cooker
hood.
To switch the lights on and off:
Press and release the knob to switch the lights on; press and
release it again to switch them off.
Note: in some models it is possible to select one of 2 different
lighting intensity levels.
To select an available suction speed (power) level:
Turn the knob in a clockwise direction to increase the suction speed
(power); turn it in an anticlockwise direction to decrease the power
until the hob is switched off.
The cooker hood is fitted with an LED (L1) which indicates the
suction speed (power) selected by displaying different colours:
Light off:
Suction motor switched off.
Fixed green light:
Cooker hood operating at power level 1 (minimum).
Fixed orange light:
Cooker hood operating at power level 2 (medium).
Fixed red light:
Cooker hood operating at power level 3 (maximum).
Flashing red light:
Cooker hood operating at an intensive power level (for a duration of
5 minutes, after which the appliance automatically selects power
level 3).
L1
L2
Fig. 3
7
Filter checking device
The cooker hood is fitted with a device which indicates when the filter
must be cleaned or replaced.
Usually the device, which signals when the carbon filter needs
maintenance work, is deactivated.
To activate it, proceed as follows:
Switch off the cooker hood.
Press and hold the knob for approximately 5 seconds.
The L2 LED begins to flash in green and after approximately 2
seconds the L2 LED will also begin to flash in orange, to indicate that
the device, which indicates when it is necessary to perform carbon
filter maintenance, has been activated.
L2 LED - grease filter indicator
The LED lights up in green when the grease filter needs to be cleaned;
this happens approximately every 40 hours of operation.
Every time the cooker hood is used, check whether the L2 LED is lit.
L2 LED - carbon filter indicator
The LED lights up in orange when the carbon filter needs to be
cleaned/replaced; this happens approximately every 160 hours of
operation.
Every time the cooker hood is used, check whether the L2 LED is lit.
Resetting the filter saturation warning
After cleaning or replacing the filters, switch on the cooker hood at any
suction speed (power), then press and hold the knob for more than 3
seconds, until you hear a beep indicating that the reset procedure has
been performed successfully. The L2 LED and the cooker hood both
switch off.
In some situations (for example, when the L2 LED is indicating that
the grease filters and the carbon filter are saturated), the procedure
described above must be repeated.
8
Maintenance and care
Before performing any maintenance operation, isolate the hood
from the electrical supply by switching off at the connector and
removing the connector fuse.
Or if the appliance has been connected through a plug and
socket, then the plug must be removed from the socket.
Cleaning the hood
Clean the outside of the hood using a damp cloth and a solution of
mild washing up liquid and washing up liquid.
Never use corrosive, abrasive or flammable cleaning products.
Never insert pointed objects in the motor’s protective grid.
Never use caustic detergents or abrasive brushes or powders.
Only ever clean the switch panel and filter grille using a damp cloth
and delicate detergents.
It is extremely important to clean the unit and change the filters at
the recommended intervals. Failure to do so will cause grease
deposits to build up that could constitute a fire hazard.
Metal grease filter
The purpose of the grease filters is to absorb grease particles
which form during cooking and it must always be used, either in
the external extraction or
internal recycling function.
Attention: the metal grease
filters must be removed and
washed, either by hand or in
the dishwasher, every four
weeks.
To access the grease filter,
first remove the front panels
which conceal the grease
filter.
Removing the front
panels:
Extract the small panel,
rotate upwards and unhook.
Repeat the operation for all
the small panels. Fig. 4.
Bild 3
Fig. 4
Unhook
Extract
9
Handle
Fig. 5
Removing the metal
grease filter
Pull the handle downards, then
extract the filter.Fig. 5.
Hand washing
Soak grease filter(s) for about
one hour in hot water with a
grease-loosening cleaner, then
rinse off thoroughly with hot
water. Repeat the process if necessary. Refit the grease filters
when they are dry.
Dishwasher
Place grease filters in the dishwasher. Select most powerful
washing programme and highest temperature, at least 65°C.
Repeat the process. Refit the grease filters when they are dry.
When washing the metal grease filter in the dishwasher a slight
discolouration of the filter can occur, this does not have any impact
on its performance.
Clean the inner housing using a hot detergent solution only (never
use caustic detergents, abrasive powders or brushes).
After having re-installed the grease filter, remount the front panels
following the instructions for removal in reverse.
The narrower front panel is to be mounted at the highest position.
10
Charcoal filter
The charcoal filter should only be used if you want to use the hood
in the recirculation mode.
To do this you will need an original charcoal filter (available from
your local Service Force Centre).
Cleaning/replacing the charcoal filter
Unlike other carbon filters, the LONGLIFE carbon filter can be
cleaned and reactivated. With normal use the filter should be
cleaned every second month (when using the hood 2,5 hours per
day, on avarage). The best way to clean the filter is in the
dishwasher. Use normal detergent and choose the highest tempera-
ture (65º C). Wash the filter separately so that no food parts gets
stuck on the filter and later causes bad odours. To reactivate the
filter, the filter should be dried in an oven for 10 minutes with a
maximum temperature of 100ºC.
After approximately three years of use, the charcoal filter should be
replaced with a new, as the odour reduction capacity will be
reduced.
Fitting
Fit the charcoal filter on the
rear side of the grease
filter, fix it with two metal
wires. Fig. 6.
Attention! The metal wires
are included in the carbon
filter packing and not on
the hood.
To remove proceed in the
reverse order.
Always specify the hood
model code number and
serial number when
ordering replacement
filters. This information is
shown on the registration
plate located on the inside
of the unit.
The charcoal filter can be
ordered from your local Service Force Centre.
grease filter
charcoal filter
metal wires
Fig. 6
11
Warning
Failure to observe the instructions on cleaning the unit and
changing the filters will cause a fire hazard. You are therefore
strongly recommended to follow these instructions.
The manufacturer declines all responsibility for any damage to the
motor or any fire damage linked to inappropriate maintenance or
failure to observe the above safety recommendations.
Changing the light bulb
Disconnect the cooker hood from the
mains supply.
Prior to touching the light bulbs ensure
they are cooled down.
Remove the lamp, use a screw driver as a
lever. Fig. 7.
Replace the old bulb with a new one of the
same type.
If the light does not come on, make sure the
bulb has been inserted correctly before
contacting your local Service Force Centre.
Special accessories
Charcoal filter Type 31
Remote control RM 7000*
Telescopic chimney K 8004 M (for extractor version only)*
Glass side panels BD 8004 W (only HD 8795)
* Not available in UK.
Fig. 7
12
Technical assistance service
You are welcome to telephone our technical assistance service (see list of technical
assistance centres) whenever you need information or in the unlikely event of a fault.
We reserve the right to change specifications and colours as a result of our policy of
continuing technological development.
Service and Spare Parts
In the event of your appliance requiring service, or if you wish to purchase spare
parts, contact your local Service Force Centre by telephoning: 08705 929 929
Your call will be automatically routed to the Service Centre covering your post code
area. For the address of your local Service Force Centre and further information
about Service Force, please visit the website at www.serviceforce.co.uk
Please ensure that you have read the section “What to do if...” as the engineer will
make a charge if the fault is not a mechanical or electrical breakdown even the
appliance is under warranty. Please note that proof of purchase is required for in-
guarantee service calls.
Help us to help you
Please determine your type of enquiry before writing or telephoning.
When you contact us we need to know:
• Your name • Clear and concise details of the fault
Address and post code • Name and model of the appliance*
• Telephone number • E number*
• Serial number*
* This information can be found on the rating plate, which can be seen when the
grease filters are removed.
If you require Customer Service in the Republic of Ireland please contact us at
the address below:
AEG
Electrolux Group (Ire) Ltd
Long Mile Road
Dublin 12
Republic of Ireland
Tel: + 353 (0) 1 4090751
13
If you require Customer Service in the Republic of Ireland please contact us at
the address below:
AEG
Electrolux Group (Ire) Ltd
Long Mile Road
Dublin 12
Republic of Ireland
Tel: + 353 (0) 1 4090751
CUSTOMER CARE DEPARTMENT
For general enquiries concerning your AEG appliance or for further
information on AEG products, please contact our Customer Care
Department by letter or telephone at the address below or visit our
website at www.aeg.co.uk
Customer Services Department
Major Appliances
AEG Electrolux
Addington Way
Luton
Bedfordshire
LU4 9QQ
08705 350 350 (*)
* calls to this number may be recorded for training purposes
14
Technical Specifications
HD 8795 HD 8760
Dimensions (in cm):
Height x Width x Depth 80 x 89,8 x 33 80 x 59,8 x 33
Maximum absorbed power: 235 W 235 W
Motor absorption: 175 W 175 W
Lighting*: 3 x 20W
(30° Ø35 12V GU4) (30° Ø35 12V GU4)
Length of the cable: 150cm 150 cm
Electrical connection: 230 V 230 V
Fuse 5A 5A
* Attention! To guarantee the same quality of illumination we advise using the
same type of light: Halogen Lamp PHILIPS STANDARD LINE Code 425409, 20W 30°
Ø35 12V GU4
Mounting accessories included
1 allen spanner for torx screw
1 support bracket
1 deflector
2 Screw caps
1 Rubber strips (to be divided in 3 pieces)
1 template
2 spacers
4 wood-screws 5 x 45 mm
4 wall plugs Ø 8 mm
2 metal screws 3,5 x 9,5
2 metal screws 3,5 x 32
2 metal screws 5 x 18
1 reduction flange Ø 150-125 mm
2 flanges Ø 150 mm
Only HD 8795: 2 Stainless Steel side panels
15
Electrical connection
Safety warnings for the electrician
The mains power supply must correspond to the rating indicated on
the plate situated inside the hood. If provided with a plug connect the
hood to a socket in compliance with current regulations and
positioned in an accessible area. If it not fitted with a plug (direct
mains connection) or if the plug is not located in an accessible area
apply a bi-polar switch in accordance with standards which assures
the complete disconnection of the mains under conditions relating to
over-current category III, in accordance with installation instructions.
IMPORTANT: Before re-connecting the hood circuit to the mains
supply and checking the efficient function, always check that the
mains cable is correctly assembled.
IMPORTANT! Power cable replacement must be undertaken by the
authorized service assistance centre or similar qualified person.
16
Warning! Do not connect the appliance to the mains until the
installation is fully complete.
Place the three rubber strips on the back of the cooker hood.
Where necessary mount the two spacers provided on the drill holes
for definitive fixing.
The spacers are useful when the wall which is to house the cooker
hood is not perfectly vertical (for example: where it is partially
covered with wall tiles).
Wall mounting - Fig. 8-9-10-11
Fig. 8
rubber strips
spacers
definitive fixing
rubber strips
rubber strips
definitive fixing
17
1
2
3
4
4
5
5
6
6
7
8
8
9
(5x18)
(5x18)
Mark the wall with a centre line, this will aid mounting procedure (1),
position the template so that the mid line printed on the template
matches with the centre line previously marked, the lower side of
the template corresponds to the lower side of the hood once
mounted (2).
Drill two holes Ø 8mm and fix the support bracket with two wall
plugs and screws (3).
Remove the front panels (see paragraph “Removing the front
panels”).
Hang the hood (4) adjust its position (5-6) and from the inside of the
hood sign two points for definitive fixing (7), remove the hood and
drill two holes Ø 8mm (8), fit two wall plugs, hang the hood again
and fix it securely with two screws (9). Cover the drill holes for
screws with the two screw caps provided.
Fig. 9
18
1
2
3
4
12
14
13
13
10a
10b
11
Fig. 10
Extractor version
Filter version
Fig. 11
HD 8795 only: Fix the
sides of the cooker
hood by fastening the
pins (10a) to the sides
of the fastening screws
(10b).
Block the sides sliding
the two tabs outwards
(11).
Make electrical
connection (12), but
leave the hood
disconnected from the
home mains circuit.
In the case that it is
decided to use the cooker
hood in the extraction mode, then fix one of the two flanges
provided in the exit hole (13 – extraction).
Attention! The tall flange should be used when a telescopic
chimney is required to be mounted (this item should be ordered –
see special accessories), the short flange is to be used in all other
cases.
Remount the grease filter and the front panels noting the numbering
on the back of each screen (from 1 to 4, top to bottom).
Connect the hood to the mains supply and check the functions are
working correctly.
19
Chère cliente, cher client,
Veuillez lire attentivement cette notice d’utilisation et notamment le
chapitre « Sécurité » que vous trouverez dans les premières pages.
Conservez cette notice d’utilisation pour pouvoir la consulter
ultérieurement. Transmettez-la à l'éventuel prochain propriétaire de
l’appareil.
Mise au rebut
Mettre au rebut les matériaux d'emballage
Tous les emballages sont recyclables, les films et les mousses sont
marqués en conséquence. Veuillez mettre au rebut les matériaux
d’emballage et éventuellement l’appareil usagé selon les règles en
vigueur.
Respectez les prescriptions nationales et régionales et le marquage
des matériaux (tri des matériaux, ramassage des déchets,
déchetteries).
Consignes de mise au rebut
L'appareil ne doit pas être jeté avec les ordures ménagères.
Renseignez-vous auprès des services de votre commune des
endroits autorisés pour la mise au rebut de l’appareil.
Attention! Rendez inutilisable l’appareil usagé avant de le mettre au
rebut. Coupez le câble d’alimentation au ras de l’appareil.
20
Sommaire
Consignes de sécurité .................................................................... 21
Généralités...................................................................................... 23
Version évacuation extérieure ............................................................ 23
Version recyclage ............................................................................. 23
Utilisation de la hotte ..................................................................... 24
Dispositif de saturation des filtres...................................................... 25
Entretien .......................................................................................... 26
Filtre à graisse métallique ................................................................. 26
Enlever les cloisons frontales ............................................................ 26
Ouverture du filtre à graisse métallique .............................................. 26
Filtre à charbon ................................................................................. 28
Remplacement de l´ampoule d’éclairage ........................................... 29
Nettoyage ........................................................................................ 29
Accessoires (en option) .................................................................. 30
Service Après-vente ....................................................................... 30
Caractéristiques techniques .......................................................... 31
Accessoires/Matériel de montage ..................................................... 31
Branchement électrique ................................................................ 32
Montage............................................................................................ 33
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Aeg-Electrolux HD 8795 Manuel utilisateur

Catégorie
Hottes
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues