Aeg-Electrolux HD 8795 Manuel utilisateur

Marque: Aeg-Electrolux

Modèle: HD 8795

Catégorie: Hottes

Taper: Manuel utilisateur

Ce manuel convient également à

HD8760-M

HD 8760 - HD 8795

User manual

Notice d'utilisation

Cooker Hood

Hotte

Contents

Safety warnings................................................................................ 3

Description of the Appliance ........................................................... 5

Extraction mode ................................................................................. 5

Recirculation mode............................................................................. 5

Control Panel .................................................................................... 6

Filter checking device......................................................................... 7

Maintenance and care...................................................................... 8

Cleaning the hood .............................................................................. 8

Metal grease filter............................................................................... 8

Removing the front panels.................................................................. 8

Removing the metal grease filter........................................................ 9

Charcoal filter ................................................................................... 10

Changing the light bulb..................................................................... 11

Special accessories ....................................................................... 11

Technical assistance service......................................................... 12

Technical Specifications ................................................................ 14

Mounting accessories included ........................................................ 14

Electrical connection ..................................................................... 15

Wall mounting................................................................................... 16

Safety warnings

• When used as an extractor unit, the hood must be fitted with a

hose having preferably the same diameter as the outlet hole.

Should there already be a pipe of diameter 125 mm that ducts to

the outside through the walls or roof, it is possible to use the 150/

125 mm reduction flange provided. In this case the hood will be

slightly noisier.

Attention: The hose is not supplied and must be purchased

separately.

• The distance between the cookware support surface on top of the

cooking appliance and the lowest part of the cooker hood must be

at least 30 cm for electric cookers or, where a gas hob is fitted,

if the cooker hood is the 60 cm size (HD 8760 model):

installation above a 60 cm gas hob - minimum distance 30 cm

installation above a 70 cm gas hob - minimum distance 45 cm

installation above gas hobs larger than 70 cm is not possible

if the cooker hood is the 90 cm size (HD 8795 model):

installation above a 60 cm or 70 cm gas hob - minimum distance

30 cm

installation above gas hobs larger than 70 cm - minimum distance

45 cm

If the instructions for installation for the gas hob specify a greater

distance, this must be adhered to.

• Before any cleaning or maintenance operation, disconnect the

hood from the mains by removing the plug or disconnecting the

home mains switch.

• The appliance is not intended for use by children or persons with

impaired physical, sensorial or mental faculties, or if lacking in

experience or know-how, unless they are under supervision or

have been trained in the use of the appliance by a person

responsible for their safety.

• Children should be monitored to ensure that they do not play with

the appliance.

• Never use the hood without effectively mounted grating.!

• The hood must NEVER be used as a support surface unless

specifically indicated.

• The premises must be sufficiently ventilated, when the kitchen

hood is used together with other gas combustion devices or other

fuels.

• The suctioned air must not be conveyed into a conduit used for the

disposal of the fumes generated by appliances that combust gases

or other fuels.

• The flaming of foods beneath the hood itself is severely prohibited.

• The use of exposed flames is detrimental to the filters and may

cause a fire risk, and must therefore be avoided in all

circumstances.

• Any frying must be done with care in order to make sure that the oil

does not overheat and burst into flames.

• Accessible parts may become hot when used with cooking

appliances.

• As regards the technical and safety measures to be adopted for

fume discharging it is important to closely follow the relations

provided by the competent authorities.

• The hood must be regularly cleaned on both the inside and outside

(AT LEAST ONCE A MONTH, it is in any event necessary to

proceed in accordance with the maintenance instructions provided

in this manual)..

• Failure to follow the instructions as concerns hood and filter

cleaning will lead to the risk of fires.

• Do not use or leave the hood without the lamp correctly mounted

because of the possible risk of electric shocks.

• We decline any responsibility for any problems, damage or fires

caused to the appliance as the result of the non-observance of the

instructions included in this manual.

This appliance is marked according to the European directive 2002/

96/EC on Waste Electrical and Electronic Equipment (WEEE).

By ensuring this product is disposed of correctly, you will help prevent

potential negative consequences for the environment and human

health, which could otherwise be caused by inappropriate waste

handling of this product.

The symbol on the product, or on the documents accompanying

the product, indicates that this appliance may not be treated as

household waste. Instead it should be taken to the appropriate

collection point for the recycling of electrical and electronic

equipment.

Disposal must be carried out in accordance with local environmental

regulations for waste disposal.

For more detailed information about treatment, recovery and recycling

of this product, please contact your local council, your household

waste disposal service or the shop where you purchased the product.

Description of the Appliance

• The hood is supplied as an extractor unit and can also be used

with a recirculation mode by fitting a charcoal filter.

• You will need an original charcoal filter for this function (Available

from your local Service Force Centre).

• Only for HD 8760: The cooker hood is supplied ready for use as a

recirculation hood and may be used for extraction by removing the

charcoal filter which has been fitted inside the cooker hood.

Extraction mode

• In this version fumes are

extracted to the outside via

a hose connected to the

coupling ring. Fig. 1.

• In order to obtain the best

performance the hose

should have a diameter

equal to the outlet hole.

• Should there already be a

pipe of diameter 125 mm

that ducts to the outside

through the walls, it is

possible to use the 150/125

mm reduction flange

provided. In this case the

hood will be slightly noisier.

Recirculation mode

• The air is filtered through a

charcoal filter and returned to

the kitchen.

• You will need an original

charcoal filter for the

recirculation mode. (See

Special Accessories).

• Fix the deflector using 2 screws

Ø 3.5x9.5 mm. Fig. 2.

coupling ring

reduction

flange

Fig. 1

Deflector

Fig. 2

Control Panel

• Best results are obtained by using a low speed for normal

conditions and a high speed when odours are more concentrated.

Turn the hood on a few minutes before you start cooking, you will

then get an under pressure in the kitchen. The hood should be left

on after cooking for about 15 minutes or until all the odours have

disappeared.

• Cooker hood operation can also be controlled using the remote

control (the remote control is an accessory and may be ordered

separately).

The control panel consists of a knob and 2 LEDs; it is

located at the bottom right-hand side of the cooker

hood.

• To switch the lights on and off:

Press and release the knob to switch the lights on; press and

release it again to switch them off.

Note: in some models it is possible to select one of 2 different

lighting intensity levels.

• To select an available suction speed (power) level:

Turn the knob in a clockwise direction to increase the suction speed

(power); turn it in an anticlockwise direction to decrease the power

until the hob is switched off.

The cooker hood is fitted with an LED (L1) which indicates the

suction speed (power) selected by displaying different colours:

• Light off:

Suction motor switched off.

• Fixed green light:

Cooker hood operating at power level 1 (minimum).

• Fixed orange light:

Cooker hood operating at power level 2 (medium).

• Fixed red light:

Cooker hood operating at power level 3 (maximum).

• Flashing red light:

Cooker hood operating at an intensive power level (for a duration of

5 minutes, after which the appliance automatically selects power

level 3).

Fig. 3

Filter checking device

The cooker hood is fitted with a device which indicates when the filter

must be cleaned or replaced.

Usually the device, which signals when the carbon filter needs

maintenance work, is deactivated.

To activate it, proceed as follows:

Switch off the cooker hood.

Press and hold the knob for approximately 5 seconds.

The L2 LED begins to flash in green and after approximately 2

seconds the L2 LED will also begin to flash in orange, to indicate that

the device, which indicates when it is necessary to perform carbon

filter maintenance, has been activated.

L2 LED - grease filter indicator

The LED lights up in green when the grease filter needs to be cleaned;

this happens approximately every 40 hours of operation.

Every time the cooker hood is used, check whether the L2 LED is lit.

L2 LED - carbon filter indicator

The LED lights up in orange when the carbon filter needs to be

cleaned/replaced; this happens approximately every 160 hours of

operation.

Every time the cooker hood is used, check whether the L2 LED is lit.

Resetting the filter saturation warning

After cleaning or replacing the filters, switch on the cooker hood at any

suction speed (power), then press and hold the knob for more than 3

seconds, until you hear a beep indicating that the reset procedure has

been performed successfully. The L2 LED and the cooker hood both

switch off.

In some situations (for example, when the L2 LED is indicating that

the grease filters and the carbon filter are saturated), the procedure

described above must be repeated.

Maintenance and care

• Before performing any maintenance operation, isolate the hood

from the electrical supply by switching off at the connector and

removing the connector fuse.

Or if the appliance has been connected through a plug and

socket, then the plug must be removed from the socket.

Cleaning the hood

• Clean the outside of the hood using a damp cloth and a solution of

mild washing up liquid and washing up liquid.

• Never use corrosive, abrasive or flammable cleaning products.

• Never insert pointed objects in the motor’s protective grid.

• Never use caustic detergents or abrasive brushes or powders.

• Only ever clean the switch panel and filter grille using a damp cloth

and delicate detergents.

• It is extremely important to clean the unit and change the filters at

the recommended intervals. Failure to do so will cause grease

deposits to build up that could constitute a fire hazard.

Metal grease filter

• The purpose of the grease filters is to absorb grease particles

which form during cooking and it must always be used, either in

the external extraction or

internal recycling function.

Attention: the metal grease

filters must be removed and

washed, either by hand or in

the dishwasher, every four

weeks.

• To access the grease filter,

first remove the front panels

which conceal the grease

filter.

Removing the front

panels:

Extract the small panel,

rotate upwards and unhook.

Repeat the operation for all

the small panels. Fig. 4.

Bild 3

Fig. 4

Unhook

Extract

Handle

Fig. 5

Removing the metal

grease filter

Pull the handle downards, then

extract the filter.Fig. 5.

Hand washing

Soak grease filter(s) for about

one hour in hot water with a

grease-loosening cleaner, then

rinse off thoroughly with hot

water. Repeat the process if necessary. Refit the grease filters

when they are dry.

Dishwasher

Place grease filters in the dishwasher. Select most powerful

washing programme and highest temperature, at least 65°C.

Repeat the process. Refit the grease filters when they are dry.

When washing the metal grease filter in the dishwasher a slight

discolouration of the filter can occur, this does not have any impact

on its performance.

• Clean the inner housing using a hot detergent solution only (never

use caustic detergents, abrasive powders or brushes).

After having re-installed the grease filter, remount the front panels

following the instructions for removal in reverse.

The narrower front panel is to be mounted at the highest position.

Charcoal filter

• The charcoal filter should only be used if you want to use the hood

in the recirculation mode.

• To do this you will need an original charcoal filter (available from

your local Service Force Centre).

• Cleaning/replacing the charcoal filter

Unlike other carbon filters, the LONGLIFE carbon filter can be

cleaned and reactivated. With normal use the filter should be

cleaned every second month (when using the hood 2,5 hours per

day, on avarage). The best way to clean the filter is in the

dishwasher. Use normal detergent and choose the highest tempera-

ture (65º C). Wash the filter separately so that no food parts gets

stuck on the filter and later causes bad odours. To reactivate the

filter, the filter should be dried in an oven for 10 minutes with a

maximum temperature of 100ºC.

After approximately three years of use, the charcoal filter should be

replaced with a new, as the odour reduction capacity will be

reduced.

• Fitting

Fit the charcoal filter on the

rear side of the grease

filter, fix it with two metal

wires. Fig. 6.

Attention! The metal wires

are included in the carbon

filter packing and not on

the hood.

• To remove proceed in the

reverse order.

• Always specify the hood

model code number and

serial number when

ordering replacement

filters. This information is

shown on the registration

plate located on the inside

of the unit.

• The charcoal filter can be

ordered from your local Service Force Centre.

grease filter

charcoal filter

metal wires

Fig. 6

Warning

• Failure to observe the instructions on cleaning the unit and

changing the filters will cause a fire hazard. You are therefore

strongly recommended to follow these instructions.

• The manufacturer declines all responsibility for any damage to the

motor or any fire damage linked to inappropriate maintenance or

failure to observe the above safety recommendations.

Changing the light bulb

• Disconnect the cooker hood from the

mains supply.

Prior to touching the light bulbs ensure

they are cooled down.

• Remove the lamp, use a screw driver as a

lever. Fig. 7.

• Replace the old bulb with a new one of the

same type.

• If the light does not come on, make sure the

bulb has been inserted correctly before

contacting your local Service Force Centre.

Special accessories

Charcoal filter Type 31

Remote control RM 7000*

Telescopic chimney K 8004 M (for extractor version only)*

Glass side panels BD 8004 W (only HD 8795)

* Not available in UK.

Fig. 7

Technical assistance service

You are welcome to telephone our technical assistance service (see list of technical

assistance centres) whenever you need information or in the unlikely event of a fault.

We reserve the right to change specifications and colours as a result of our policy of

continuing technological development.

Service and Spare Parts

In the event of your appliance requiring service, or if you wish to purchase spare

parts, contact your local Service Force Centre by telephoning: 08705 929 929

Your call will be automatically routed to the Service Centre covering your post code

area. For the address of your local Service Force Centre and further information

about Service Force, please visit the website at www.serviceforce.co.uk

Please ensure that you have read the section “What to do if...” as the engineer will

make a charge if the fault is not a mechanical or electrical breakdown even the

appliance is under warranty. Please note that proof of purchase is required for in-

guarantee service calls.

Help us to help you

Please determine your type of enquiry before writing or telephoning.

When you contact us we need to know:

• Your name • Clear and concise details of the fault

• Address and post code • Name and model of the appliance*

• Telephone number • E number*

• Serial number*

* This information can be found on the rating plate, which can be seen when the

grease filters are removed.

If you require Customer Service in the Republic of Ireland please contact us at

the address below:

AEG

Electrolux Group (Ire) Ltd

Long Mile Road

Dublin 12

Republic of Ireland

Tel: + 353 (0) 1 4090751

Email: [email protected]

If you require Customer Service in the Republic of Ireland please contact us at

the address below:

AEG

Electrolux Group (Ire) Ltd

Long Mile Road

Dublin 12

Republic of Ireland

Tel: + 353 (0) 1 4090751

Email: [email protected]

CUSTOMER CARE DEPARTMENT

For general enquiries concerning your AEG appliance or for further

information on AEG products, please contact our Customer Care

Department by letter or telephone at the address below or visit our

website at www.aeg.co.uk

Customer Services Department

Major Appliances

AEG Electrolux

Addington Way

Luton

Bedfordshire

LU4 9QQ

08705 350 350 (*)

* calls to this number may be recorded for training purposes

Technical Specifications

HD 8795 HD 8760

Dimensions (in cm):

Height x Width x Depth 80 x 89,8 x 33 80 x 59,8 x 33

Maximum absorbed power: 235 W 235 W

Motor absorption: 175 W 175 W

Lighting*: 3 x 20W

(30° Ø35 12V GU4) (30° Ø35 12V GU4)

Length of the cable: 150cm 150 cm

Electrical connection: 230 V 230 V

Fuse 5A 5A

* Attention! To guarantee the same quality of illumination we advise using the

same type of light: Halogen Lamp PHILIPS STANDARD LINE Code 425409, 20W 30°

Ø35 12V GU4

Mounting accessories included

1 allen spanner for torx screw

1 support bracket

1 deflector

2 Screw caps

1 Rubber strips (to be divided in 3 pieces)

1 template

2 spacers

4 wood-screws 5 x 45 mm

4 wall plugs Ø 8 mm

2 metal screws 3,5 x 9,5

2 metal screws 3,5 x 32

2 metal screws 5 x 18

1 reduction flange Ø 150-125 mm

2 flanges Ø 150 mm

Only HD 8795: 2 Stainless Steel side panels

Electrical connection

Safety warnings for the electrician

The mains power supply must correspond to the rating indicated on

the plate situated inside the hood. If provided with a plug connect the

hood to a socket in compliance with current regulations and

positioned in an accessible area. If it not fitted with a plug (direct

mains connection) or if the plug is not located in an accessible area

apply a bi-polar switch in accordance with standards which assures

the complete disconnection of the mains under conditions relating to

over-current category III, in accordance with installation instructions.

IMPORTANT: Before re-connecting the hood circuit to the mains

supply and checking the efficient function, always check that the

mains cable is correctly assembled.

IMPORTANT! Power cable replacement must be undertaken by the

authorized service assistance centre or similar qualified person.

• Warning! Do not connect the appliance to the mains until the

installation is fully complete.

• Place the three rubber strips on the back of the cooker hood.

Where necessary mount the two spacers provided on the drill holes

for definitive fixing.

The spacers are useful when the wall which is to house the cooker

hood is not perfectly vertical (for example: where it is partially

covered with wall tiles).

Wall mounting - Fig. 8-9-10-11

Fig. 8

rubber strips

spacers

definitive fixing

rubber strips

definitive fixing

(5x18)

• Mark the wall with a centre line, this will aid mounting procedure (1),

position the template so that the mid line printed on the template

matches with the centre line previously marked, the lower side of

the template corresponds to the lower side of the hood once

mounted (2).

• Drill two holes Ø 8mm and fix the support bracket with two wall

plugs and screws (3).

• Remove the front panels (see paragraph “Removing the front

panels”).

• Hang the hood (4) adjust its position (5-6) and from the inside of the

hood sign two points for definitive fixing (7), remove the hood and

drill two holes Ø 8mm (8), fit two wall plugs, hang the hood again

and fix it securely with two screws (9). Cover the drill holes for

screws with the two screw caps provided.

Fig. 9

10a

10b

Fig. 10

Extractor version

Filter version

Fig. 11

• HD 8795 only: Fix the

sides of the cooker

hood by fastening the

pins (10a) to the sides

of the fastening screws

(10b).

Block the sides sliding

the two tabs outwards

(11).

• Make electrical

connection (12), but

leave the hood

disconnected from the

home mains circuit.

• In the case that it is

decided to use the cooker

hood in the extraction mode, then fix one of the two flanges

provided in the exit hole (13 – extraction).

Attention! The tall flange should be used when a telescopic

chimney is required to be mounted (this item should be ordered –

see special accessories), the short flange is to be used in all other

cases.

• Remount the grease filter and the front panels noting the numbering

on the back of each screen (from 1 to 4, top to bottom).

• Connect the hood to the mains supply and check the functions are

working correctly.

Chère cliente, cher client,

Veuillez lire attentivement cette notice d’utilisation et notamment le

chapitre « Sécurité » que vous trouverez dans les premières pages.

Conservez cette notice d’utilisation pour pouvoir la consulter

ultérieurement. Transmettez-la à l'éventuel prochain propriétaire de

l’appareil.

Mise au rebut

Mettre au rebut les matériaux d'emballage

• Tous les emballages sont recyclables, les films et les mousses sont

marqués en conséquence. Veuillez mettre au rebut les matériaux

d’emballage et éventuellement l’appareil usagé selon les règles en

vigueur.

• Respectez les prescriptions nationales et régionales et le marquage

des matériaux (tri des matériaux, ramassage des déchets,

déchetteries).

Consignes de mise au rebut

• L'appareil ne doit pas être jeté avec les ordures ménagères.

• Renseignez-vous auprès des services de votre commune des

endroits autorisés pour la mise au rebut de l’appareil.

• Attention! Rendez inutilisable l’appareil usagé avant de le mettre au

rebut. Coupez le câble d’alimentation au ras de l’appareil.

Sommaire

Consignes de sécurité .................................................................... 21

Généralités...................................................................................... 23

Version évacuation extérieure ............................................................ 23

Version recyclage ............................................................................. 23

Utilisation de la hotte ..................................................................... 24

Dispositif de saturation des filtres...................................................... 25

Entretien .......................................................................................... 26

Filtre à graisse métallique ................................................................. 26

Enlever les cloisons frontales ............................................................ 26

Ouverture du filtre à graisse métallique .............................................. 26

Filtre à charbon ................................................................................. 28

Remplacement de l´ampoule d’éclairage ........................................... 29

Nettoyage ........................................................................................ 29

Accessoires (en option) .................................................................. 30

Service Après-vente ....................................................................... 30

Caractéristiques techniques .......................................................... 31

Accessoires/Matériel de montage ..................................................... 31

Branchement électrique ................................................................ 32

Montage............................................................................................ 33

La page charge ...

Aeg-Electrolux HD 8795 Manuel utilisateur

Marque: Aeg-Electrolux

Modèle: HD 8795

Catégorie: Hottes

Taper: Manuel utilisateur

Ce manuel convient également à

HD8760-M

Télécharger le PDF

rapport

dans d''autres langues

English: Aeg-Electrolux HD 8795 User manual

Aeg-Electrolux HD 8795 Manuel utilisateur

Ce manuel convient également à

Aeg-Electrolux HD 8795 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents