GE Profile PDW1800KWW Guide d'installation

Marque: GE Profile

Modèle: PDW1800KWW

Catégorie: Lave-vaisselle

Taper: Guide d'installation

GE Consumer & Industrial

Appliances

ilt-In Dishwasher

f you have questions, call 800.GE.CARES (800.432.27

37) or visit our website at

: www.ge.com

imagination at work

IMPORTANT

– The dishwasher MUST

be installed to allow for future removal from the enclosure

if service is required.

If you received a damaged dishwasher, you should

immediately contact your dealer or builder.

Optional Accessories – See the Owner’s Manual for available

custom panel kits.

FOR YOUR SAFETY

Read and observe all CAUTIONS and WARNINGS

shown throughout these instructions. While performing

installations described in this booklet, gloves and either

safety glasses or goggles should be worn.

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

IMPORTANT

– Observe all governing codes and

ordinances.

•

Note to Installer

– Be sure to leave these instructions for the

consumer’s and local inspector’s use.

•

Note to Consumer

– Keep these instructions with your

Owner’s Manual for future reference.

•

Skill Level

– Installation of this dishwasher requires

basic mechanical, electrical and plumbing skills.

Proper

installation is the responsibility of the installer. Product

failure due to improper installation is not covered under

the GE Appliance Warranty. See warranty information.

•

Completion Time – 1 to 3 Hours

. New installations require

more time than replacement installations.

BEFORE YOU BEGIN

Read these instructions completely and

carefully.

STOP

Top of Panel

7-11/16"

Trim Around

Dotted Line

2-5/32"

(5.5 cm)

(19.5 cm)

Trim Around Dotted Line

Drill 3/32"

Pilot Hole

3/32" Deep

Top of Panel

7-11/16"

2-5/32"

(5.5 cm)

(19.5 cm)

Drill 3/32"

Pilot Hole

3/32" Deep

Drill 3/32"

Pilot Hole

3/32" Deep

13/32"

(1 cm)

6-1/2"

(16.5 cm)

5-29/32"

(15 cm)

Drill 3/32"

Pilot Hole

3/32" Deep

13/32"

(1 cm)

6-1/2"

(16.5 cm)

5-29/32"

(15 cm)

Bracket

Spacer Pad

Spacer

3/4" Thick Custom Panel

Template Instructions for 18"

Top Control Integrated Proﬁ le and

Monogram Dishwasher Models

Pub. No. 31-30244

Dwg. No. 206C1559P182

05-08 JR

The custom panel should be sized to your installation situation. See Step 1. For easier

installation, the custom panel and custom handle should be attached before installing the

dishwasher. Use this template to locate mounting screws and spacers on the custom panel.

IMPORTANT

• A custom handle must be installed onto the

custom panel. Install the custom handle 4-1/2"

max. from the top of the panel.

STEP 2 DRAW CENTERLINE

• Place the custom panel on a ﬂ at surface with the

appearance side down.

• Locate the vertical center of the panel at the top.

• Use a carpenter's square to draw a centerline from

top to bottom.

STEP 3 ALIGN TEMPLATE TO PANEL

• Trim template on the dotted line along all sides.

• Place the template on the panel aligned with the top

edge and the centerline. Use tape to hold in place.

IMPORTANT: If the template is not aligned with the top

edge of the panel, the 1/2" minimum gap will not be maintained.

This 1/2" minimum gap must be maintained to prevent condensation

and damage to the control panel from screw heads.

• Use an awl to mark the screw hole locations indicated

on the template. Remove the template.

HEIGHT

Panel height should be 26-25/32" (68 cm).

• The top of the custom panel must be ﬂ ush

with the top of the door. The 1/2" minimum gap

between the top of the door and the bottom of

the countertop must be maintained.

PARTS INCLUDED:

(2) Brackets

(4) 1/2" Phillips ﬂ at-head screws

(2) Spacer pads

(2) Metal spacers

(2) 1" Phillips ﬂ at-head screws

(2) 3/4" Phillips round-head screws

STEP 1 CUSTOM PANEL SIZE REQUIREMENTS

IMPORTANT: To ensure optimum door balance

performance, the custom panel must not weigh

more than 8 lbs.

WIDTH

Panel width must be 17-1/2" (44.4 cm).

• If the panel width is less than 17-1/2", it will

not cover the dishwasher frame.

STEP 7 CHECK DOOR BALANCE

To check the door balance, hold the top of the

dishwasher ﬁ rmly.

• Check the door balance by opening and closing

the door.

• If the door drops when released, increase the

spring tension. If the door rises when released,

decrease the spring tension.

• Using a T25 torque driver, adjust in the direction

shown. Adjust both sides equally.

STEP 6 INSTALL ASSEMBLED PANEL

• Secure the panel to the door by inserting

the top metal spacers and bottom brackets

into the matching slots on the dishwasher

door and control panel.

• Make sure both metal spacers

and both brackets engage the slots.

• Press the panel against the door and push

downward until the metal spacers and brackets

are fully engaged into the slots. The panel should

align evenly with the top and sides.

• Stand the dishwasher upright.

• Open the dishwasher door and remove the

2 plug buttons, one on each side as shown.

• Place the supplied 3/4" Phillips round-head

screws inside the plastic sleeve and drive

through the inner door and into the custom

panel.

• Replace the 2 plug buttons by pressing them

ﬁ rmly back into the plastic sleeve.

WARNING: Do not overtighten screws. Excessive

tightening of the screws could damage door edges.

STEP 5 INSTALL CUSTOM HANDLE

A custom handle must be installed onto the panel

before the panel is secured to the dishwasher door.

• The handle should be installed so that it aligns with

adjacent drawer handles, or 4-1/2" max. from the top

of the panel. Secure the handle in the same manner

as the cabinet handles. Screws must be

countersunk into the panel.

STEP 4 INSTALL MOUNTING SCREWS AND SPACERS

Note: The custom panel is secured to the dishwasher door

with the metal spacers, screws and brackets provided.

The metal spacers and brackets will slip into the slots

on the dishwasher door and control panel.

• Align the metal spacers over the top pilot holes. Ensure

the thick, recessed side is facing up.

• Drive the supplied 1" Phillips ﬂ at-head screws through

the metal spacers and into the panel.

• Align the brackets over the bottom pilot holes. Ensure

the curved lip is facing up. If the back surface of the

panel is not ﬂ at, use the spacer pads provided.

• Drive the 1/2" Phillips ﬂ at-head screws through the

brackets and into the panel.

Countertop

Minimum 1/2" gap

for clearance

1/2" minimum

Mark center

screw holes

Handle

4 1/2" Max.

from top

of panel

Custom

door panel

Screws must be counter-

sunk into panel

Custom

panel

Dishwasher

door

Custom panel

PARTS SUPPLIED

(2) Brackets(2) Spacer Pads

(2) Metal spacers

(2) 3/4" Round-head

screws

(2) 1" Phillips ﬂ at-head

screws

(4) 1/2" Phillips ﬂ at-head

screws

Increase

Decrease

Increase

Support

Entretoise

Instructions de gabarit pour panneau

sur mesure épais de 19 mm (3/4 po) pour

modèle de lave-vaisselle de 18 po

à réglage intégré en haut Proﬁ le

et Monogram

Pub. No. 31-30244

Dwg. No. 206C1559P182

05-08 JR

Le panneau de ﬁ nition doit avoir des dimensions appropriées pour l’installation. Consulter l’étape 1.

Pour faciliter l’installation, le panneau de ﬁ nition et la poignée de ﬁ nition doivent être montés avant

la mise en place du lave-vaisselle. Utiliser ce gabarit pour déterminer l’emplacement

des vis de montage et des rondelles sur le panneau de ﬁ nition

IMPORTANT

• Il faut installer une poignée de ﬁ nition sur

le panneau de ﬁ nition. Installer la poignée à moins

de 11,5 cm (4-1/2 po) du haut du panneau.

ÉTAPE 2 TRAÇAGE DE L’AXE

• Mettre le panneau de ﬁ nition sur une surface plate, le côté

extérieur vers le bas.

• Mettre le centre vertical du panneau en haut.

• Avec une équerre de menuisier, tracer un axe du haut au bas.

ÉTAPE 3 ALIGNER LE GABARIT SUR LE PANNEAU

• Couper le gabarit suivant le pointillé, sur tous les côtés.

• Mettre le gabarit sur le panneau, aligné sur le bord supérieur

et sur l’axe. Le maintenir en place avec du ruban adhésif.

IMPORTANT : Si le gabarit n’est pas aligné à l’extrémité du haut

du panneau, vous n’obtenez pas 1/2 po d’espace libre. Vous devez

avoir un espace libre de 1/2 po pour empêcher la condensation

et éviter d’endommager le panneau de contrôle avec les têtes de vis.

• Avec un pointeau, marquer les emplacements de trous de vis indiqués

sur le gabarit. Enlever le gabarit.

HAUTEUR

Panel height doit être de 26 25/32 po (68 cm)

• Le haut du panneau sur mesure doit afﬂ eurer

le haut de la porte. Il doit y avoir un espace libre

d’au moins 1/2 po entre le haut de la porte

et le bas du revêtement de comptoir.

PIÈCES INCLUSES:

(2) Supports

(4) Vis à tête plate Phillips ½ po

(2) Coussinets d’espacement

(2) Espaceurs métalliques

(2) Vis à tête plate Phillips 1 po

(2) Vis à tête rond Phillips ¾ po

ÉTAPE 1 TAILLE NÉCESSAIRE POUR LE PANNEAU SUR MESURE

IMPORTANT : Pour que la porte fonctionne bien,

le panneau sur mesure ne doit pas peser plus

de 6,4 kilos (14 livres).

LARGEUR

Le panneau doit avoir au moins 17 1/2 po de largeur.

• Si le panneau a moins de 17 1/2 po de largeur,

il ne couvre pas le châssis de porte

du lave-vaisselle.

• Mettez le lave-vaisselle debout.

• Ouvrez la porte du lave-vaisselle et ôtez les deux

bouchons, un de chaque côté tel qu’illustré.

• Placez les vis à tête plate Phillips ¾ po à l’intérieur

du manchon de plastique et vissez à travers la porte

intérieure puis dans le panneau sur mesure.

• Replacez les deux bouchons en les enfonçant

fermement dans le manchon de plastique.

ATTENTION : Il ne faut pas serrer les vis en excès.

Un serrage excessif des vis peut endommager

les bords de la porte.

ÉTAPE 4 INSTALLER LES VIS DE MONTAGE ET LES RONDELLES

Remarque: Le panneau sur mesure est ﬁ xé à la porte

du lave-vaisselle à l’aide des espaceurs métalliques,

des vis et des supports fournis. Les espaceurs métalliques

et les supports glissent dans les fentes de la porte du lave-vaisselle

et du panneau de commande.

• Alignez les espaceurs métalliques sur les trous guides supérieurs.

Veillez à ce que la face épaisse et encastrée soit orientée vers

le haut.

• Vissez les vis à tête plate Phillips 1 po à travers les espaceurs

métalliques puis dans le panneau.

• Alignez les supports sur les trous guides inférieurs.

Assurez-vous que la lèvre incurvée est orientée vers le haut.

Si la surface arrière du panneau n’est pas plane, utilisez

les coussinets d’espacement fournis.

• Vissez les vis à tête plate Phillips ½ po à travers les supports puis

dans le panneau.

Plan de travail

Jeu minimum de 1/2 po

pour le dégagement

Min. 1/2 po

Marquer le centre

des trous de vis

Poignée

Moins de

115 mm

(4-1/2 po)

du haut du

panneau

Panneau de ﬁ nition

de la porte

Les vis doivent être noyées

dans le panneau

Panneau

de ﬁ nition

Porte de

lave-vaisselle

Panneau

de ﬁ nition

LES PIÈCES ONT FOURNI

(2) Supports(2) Coussinets d’espacement

(2) Espaceurs métalliques

(2) Vis à tête rond

Phillips ¾ po

(2) Vis à tête plate

Phillips 1 po

(4) Vis à tête plate

Phillips ½ po

Augmenter

Diminuer

Augmenter

ÉTAPE 5 INSTALLATION DE LA POIGNÉE DE FINITION

Installer une poignée de ﬁ nition sur le panneau avant

de monter le panneau sur la porte du lave-vaisselle.

• Il faut aligner la poignée sur les poignées des tiroirs

adjacents ou à moins de 115 mm (4-1/2 po) du haut

du panneau. Monter la poignée de la même manière

que les poignées de l’armoire. Les vis doivent être

noyées dans le panneau.

ÉTAPE 6 INSTALLATION DU PANNEAU ASSEMBLÉ

• Fixez le panneau à la porte en insérant les espaceurs

métalliques supérieures et les supports inférieurs dans

les fentes correspondantes de la porte du lave-vaisselle

et du panneau de commande.

• Assurez-vous que tous les espaceurs

et supports s’engagent bien dans les fentes.

• Appuyez le panneau contre la porte et poussez

vers le bas jusqu’à ce que les espaceurs et les supports

soient engagés à fond dans les fentes. Le panneau doit

s’aligner uniformément sur le dessus et les côtés.

ÉTAPE 7 VÉRIFIER L’ÉQUILIBRE DE LA PORTE

Agrippez d’abord le haut de la porte fermement.

• Vériﬁ ez l’équilibre en ouvrant et fermant la porte.

• Si la porte tombe lorsque relâchée, augmentez

la tension du ressort. Si au contraire elle remonte,

diminuez la tension.

• À l’aide d’un tournevis dynamométrique T25,

effectuez le réglage dans la direction indiquée.

Réglez les deux côtés également.

Coussinets

d’espacement

PARTS SUPPLIED:

■

Two #8 Phillips head wood screws, 5/8" long to

secure dishwasher to underside of countertop

(in literature package).

Installation Preparation

TOOLS YOU WILL NEED:

■

Phillips head screwdriver

■

5/16" and 1/4" nutdriver

■

T25 torque driver (PDW__II only)

■

6" Adjustable wrench

■

Level

■

Carpenters square

■

Measuring tape

■

Safety glasses

■

Flashlight

■

Bucket to catch water when flushing the line

■

Gloves

For New Installations Only:

■

Tubing cutter

■

Drill and appropriate bits

■

Hole saw set

MATERIALS YOU WILL NEED:

■

Ferrule, compression nut and 90° Elbow (3/8" NPT

external thread on one end, opposite end sized to

fit water supply)

■

Thread seal tape

■

UL Listed wire nuts (3)

Materials For New Installations Only:

■

Air gap for drain hose, if required

■

Waste tee for house plumbing, if applicable

■

Electrical cable or power cord, if applicable

■

Screw type hose clamps

■

Strain relief for electrical connection

■

Hand shut-off valve

■

Water line 3/8" min. copper

■

Coupler for extending drain line, if applicable

Hose Clamps

90 ϒ Elbow

Air Gap

Carpenters Square

Coupler

Drill & Bits

Electrical Cable

Flashlight

Hand Valve

Hole Saw Bit

Level 2

Measuring Tape

Nutdriver

Safety Glasses

Screw Driver II

Tape

Tubing Cutter

Wire Nuts

2 Wood Screws

Hand

Shut-Off

Valve

90° Elbow,

Ferrule and

Compression Nut

Thread

Seal Tape

Wire Nuts (3)

Hot Water Line

Electrical Cable

(or Power Cord, if applicable)

Waste Tee

Coupler

Air

Gap

Screw Type

Hose Clamps

Strain Relief

Phillips

Head

Screwdriver

1/4" and

5/16" Nutdriver

Level

Carpenters

Square

T25 Torque

Driver

6" Adjustable

Wrench

Tubing Cutter

Measuring Tape

Safety Glasses

Flashlight

Gloves

Bucket

Hole Saw Set

Drill and Bits

Waste Tee

Strain Relief

Hot Water Line

GLOVES

Bucket

Crescent Wrench

Wood Screw

Installation Preparation

PREPARE DISHWASHER ENCLOSURE

• The rough cabinet opening must be at least 24" deep, 17-5/8"

to 18" wide and approximately 34-1/2" high from ﬂ oor to

underside of the countertop.

• The dishwasher must be installed so that drain hose is no

more than 10’ in length for proper drainage.

WARNING

To reduce the risk of electric shock, ﬁ re, or injury to persons, the

installer must ensure that the dishwasher is completely enclosed

at the time of installation.

CLEARANCES:

When

installed into a corner,

allow 2” min. clearance

between dishwasher and

adjacent cabinet, wall or

other appliances. Allow

25-5/8" min. clearance

from the front of the

dishwasher for door

opening. Figure B

DRAIN REQUIREMENTS

• Follow local codes and ordinances.

• Do not exceed 10’ distance to drain.

• Do not connect drain lines from other devices to the

dishwasher drain hose.

NOTE:

Air gap must be used if waste tee or disposer connection

is less than 18" above floor to prevent siphoning.

DETERMINE DRAIN METHOD

The type of drain installation depends on the following

questions.

■

Do local codes or ordinances require an air gap?

■

Is waste tee less than 18" above floor?

If the answer to either question is YES, Method 1 MUST

be used.

• If the answers are NO, either method may be used.

CABINET PREPARATION

• Drill a 1-1/2" diameter hole in the cabinet wall within

the shaded areas shown in Figure A for the drain hose

connection. The hole should be smooth with no sharp edges.

IMPORTANT:

When connecting

drain line to disposer, check to be

sure that drain plug has been

removed. DISHWASHER WILL NOT

DRAIN IF PLUG IS LEFT IN PLACE.









Method 1 – Air Gap with Waste Tee or Disposer

An air gap must be used when required by local codes and ordinances.

The air gap must be installed according to manufacturer’s instructions.

Method 2 – Drain Hose Routing

When

not using an air gap, the drain hose must be routed to for

m a high

loop of at least 32" to prevent s

iphoning. See Step 15 on page 10.

Figure C

Figure D

Figure B

















Cabinets

Squar

and

Plumb

Floor MUST

be Even wit

Room Floo

This Wall Area

must be Free of

Pipes or wires

Plumbing and Electric Service

Must Enter Shaded Area

34-1/2"

± 1/2"

Underside of

Counterto

to Floor

24"

Min

17 5/8" Min.

18" Max

5" 5"

2514A

Clearance for Door

Opening 2" Minimum

Countertop

Dishwasher

25-5/8"

2514B

Figure A

CAUTION:

An air gap

MUST BE USED

if the drain hose is connected to

waste tee or disposer lower than 18" above the floor level.

Failure to provide the proper drain connection height with an

air gap or 32" minimum high drain loop will result in improper

draining of the dishwasher, which may cause damage.

Installation Preparation

PREPARE ELECTRICAL WIRING

#282 French

FOR PERSONAL SAFETY:

Remove house fuse or open circuit breaker

before beginning installation. Do not use

an extension cord or adapter plug with this

appliance.

#282 French

The improper connection of the equipment

grounding conductor can result in electric

shock. Check with a qualified electrician or

service representative if you are in doubt that

the appliance is properly grounded. Do not

modify the plug provided with the appliance;

if it will not fit the outlet, have a proper outlet

installed by a qualified technician.

For models equipped with power cord:

Do not modify the plug

provided with the appliance; if it will not fit the outlet, have a

proper outlet installed by a qualified technician.

Cabinet Preparation and Wire Routing

• The wiring may enter the opening from either side, rear or the

ﬂ oor within the shaded area.

• Cut a 1-1/2" max. diameter hole to admit the electrical cable.

Cable direct connections may pass through the same hole

as the drain hose and hot water line, if convenient. If cabinet

wall is metal, the hole edge must be covered with a bushing.

Note:

Power cords with plug must pass through a separate

hole.

Electrical Connection to Dishwasher

Electrical connection is on the right front of dishwasher.

• For cable direct connections the cable must be routed as

shown in Figure E. Cable must extend a minimum of 24" from

the rear wall.

• For power cord connections, install a 3-prong grounding type

receptacle in the sink cabinet rear wall, 6" min. or 18" max.

from the opening, 6" to 18" above the ﬂ oor.

Figure E

WARNING

Electrical Requirements

• This appliance must be supplied with 120V, 60Hz., and

connected to an individual properly grounded branch circuit

protected by a 15 or 20 ampere circuit breaker or time delay

fuse.

• Wiring must be 2 wire with ground and rated for 75°C (176°F).

• If the electrical supply does not meet the above

requirements, call a licensed electrician before proceeding.

Grounding Instructions–Cable Direct

This appliance must be connected to a grounded metal,

permanent wiring system, or an equipment grounding

conductor must be run with the circuit conductors and be

connected to the equipment grounding terminal or lead on the

appliance.

Grounding Instructions–Power Cord Models

This appliance must be grounded. In the event of a

malfunction

or breakdown, grounding will reduce the

risk of electric shock

by providing a path of least resistance

for electric current.

This appliance is equipped

with a cord having an equipment

grounding conductor

and a grounding plug. The plug must

be plugged into an

appropriate outlet that is installed and

grounded in

accordance with all local codes and ordinances.

1-1/2” Dia.

Hole (Max.)

3”

from

Cabinet

24”

from Wall

Ground

Black

White

Installation Instructions

PREPARE HOT WATER LINE

• The line may enter from either side, rear or ﬂ oor within the

shaded area shown in Figure F.

• The line may pass through the same hole as the electrical

cable and drain hose. Or, cut an additional 1-1/2" dia. hole to

accommodate the water line. If power cord with plug is used,

water line must not pass through power cord hole.

Figure F

Water Line Connection

• Turn off the water supply.

• Install a hand shut-off valve in an accessible location, such

as under the sink. (Optional, but strongly recommended and

may be required by local codes.)

• Water connection is on the left side of the dishwasher. Install

the hot water inlet line, using no less than 3/8" O.D. copper

tubing. Route the line as shown in Figure F and extend

forward at least 18" from rear wall.

• Adjust water heater for 120°F to 150°F temperature.

• Flush water line to clean out debris.

• The hot water supply line pressure must be 20-120 PSI.

CAUTION:

Opening the door will cause the dishwasher

to tip forward.

Do not open the door

until you are ready

to install the dishwasher.

If it is

necessary to open the door, hold

the top of the dishwasher securely

with one hand and hold the door

with the other hand.

STOP

BEFORE YOU BEGIN

Locate and set aside the package containing

2 Phillips head countertop mounting screws

and 2 additional toekick screws (located in

the literature package).

Figure G

STEP 1 CHECK DOOR BALANCE

To check the door balance, hold the top of the dishwasher

ﬁ rmly.

• Check the door balance by opening and closing the door.

• If the door drops when released, increase the spring tension.

If the door rises when released, decrease the spring tension.

• Models have different spring mounting and tension methods.

Refer to the appropriate ﬁ gure for your model.

Figure H

CAUTION:

The hot water supply line pressure must be at least 20 psi.

Lower pressures could cause the water valve to leak and

cause water damage.

Cabinet Face

Shut-off

Valve

3" From Floor

18" From Wall

From

Cabinet

1-1/2" Dia.

Hole

Hot

Decrease

Increase

PDW1800_II models only

Increase

Decrease Decrease

Installation Instructions

STEP 2 ADJUST LEVELING LEGS

• Move the dishwasher close to the installation location and lay

it on its back.

Figure I

• Measure installation height and dishwasher height. Extend

leveling legs out from the dishwasher base, 1/2" less than

installation height.

STEP 3 REMOVE TOEKICK

• Remove the 4 toekick screws. Lift off the 2 piece toekick.

STEP 4 INSTALL POWER CORD

Skip this step if dishwasher will be direct wired.

Use Power Cord Kit WX09X70910, available for purchase

from an authorized GE Appliance Dealer. The power cord and

connections must comply with the National Electrical Code,

Section 422 and/or local codes and ordinances.

• Maximum power cord length is 6'.

• Connect incoming power cord white (or ribbed) to dishwasher

white, black (or smooth) to black and ground to dishwasher

green wire. Use UL listed wire nuts of appropriate size.

• Replace junction box cover. Be sure wires are not pinched

under the cover.

Figure K

Figure J

Figure L

STEP 5 INSTALL 90° ELBOW

• Wrap 90° elbow with thread seal tape.

• Install a 90° elbow onto the water valve.

• Do not over tighten 90° elbow, water valve bracket could

bend or water valve ﬁ tting could break.

• Position the end of the elbow to face the rear of the

dishwasher.

Adjust to

Installation

Height

Remove

4 Toekick

Screws

White

Ground

Black

Check That White, Black and

Green Dishwasher Wires Are Threaded

Thru Hole in Back

Remove

Junction Box

Cover

Insert Power

Cord Wires Thru

Strain Relief

and Tighten

Use UL Listed

Wire Nuts

90°

Elbow

Fill

Hose

Thread

Seal Tape

ter

lve

Bracket

Installation Instructions

STEP 6 POSITION WATER LINE AND

HOUSE WIRING

• Position water supply line and house wiring on the ﬂ oor of

the opening to avoid interference with base of dishwasher

and components under dishwasher.

Figure M

Figure N

Figure O

STEP 7 INSTALL DRAIN HOSE THROUGH

CABINET

• Stand the dishwasher upright and position in front of the

opening. Insert drain hose into cabinet wall hole. If a power

cord is used, guide the end through a separate hole.

TIP:

Position water line and house wiring on the floor

to avoid interference with base of dishwasher.

STEP 8 SLIDE DISHWASHER PARTIALLY

INTO CABINET

DO NOT PUSH AGAINST FRONT PANEL WITH KNEES.

DAMAGE WILL OCCUR

• Slide dishwasher into the opening a few inches at a time.

• As you proceed, pull the drain hose through the opening

under the sink. Stop pushing when the dishwasher is a few

inches forward of adjacent cabinetry.

• Make sure drain hose is not kinked under the dishwasher and

there is no interference with the water line and wiring or any

other component.

Water

Line

House

Wiring

Power Cord

(If Used)

Water

Line

House

Wiring

Drain

Hose

Insulation

Blanket

Maximum

Drain Hose

Length 10”

Do Not Push Against

Front Door Panel With

Knee. Damage to The

Door Panel Will Occur.

Countertop

Figure T

Dishwasher

Door

1/2”

Min.

Installation Instructions

STEP 9 POSITION DISHWASHER UNDER

COUNTERTOP

• Push the dishwasher into the cabinet.

• Push the sides with your hands. Do not use your knee against

the door since door damage will occur.

• Check that the tub insulation blanket does not get

“bunched-up” or interfere with the springs as you slide it

into the cabinet.

• Center the dishwasher in the opening.

• Front of door panel should be ﬂ ush with face of cabinet.

• Carefully open and close the door to ensure that the door

panel does not catch or rub on the cabinet frame.

• If the door catches or rubs on the frame, reposition and/or

level the unit (see Step 10) until the door moves freely and

does not contact the cabinet frame.

The controls on these models are designed to be hidden by

your countertop. Align the dishwasher as shown in Figure

Q. Leave a 1/2" minimum gap between the underside of the

countertop and the top of the dishwasher door as shown in

Figure T.

Note:

If the drain hose gets trapped behind the unit it can

prevent the controls from being hidden by the countertop.

Note:

If this dishwasher is replacing an existing dishwasher, the

old countertop bracket screw holes may not be in the correct

position to accept a top-control model. New holes may be

required.

Tip:

The leveling legs can be used to increase or decrease

the amount of gap between the controls and the countertop

affecting the visibility of the controls.

IMPORTANT

– Leave a 1/2" minimum gap between

the controls and the underside of the countertop to prevent

condensation and damage to the control panel from

screwheads.

Figure P

Figure Q

Figure R

Figure S

Figure T















































Countertop

Figure S

Control

Panel

OFF

DELAY

START

LOW RINSE AID

1 - 24 HRS.

Top View

Controls Hidden

by Countertop

Installation Instructions

STEP 10 LEVEL DISHWASHER

IMPORTANT

– Dishwasher must be level for proper

dish rack operation and wash performance.

• Make sure 1/2" minimum gap is maintained (see Figure T).

• Place level on door to check that the dishwasher is level side-

to-side. Place level on rack track inside tub to check that the

dishwasher is level front-to-back.























• If the dishwasher is not level, adjust the four leveling legs

individually.

Tip: Pull lower rack out, about halfway. Check to be sure the

rack does not roll forward or back into dishwasher. If the rack

rolls in either direction, the dishwasher must be leveled again.

• If door hits the tub, the dishwasher is not installed correctly.

Adjust leveling legs to align door to tub.

IMPORTANT

– After leveling, verify that the

dishwasher is still in the correct position shown in

Step 9.

Figure U

Figure V

STEP 11 SECURE DISHWASHER TO

COUNTERTOP OR CABINET

In this step you will need

the 2 Phillips special head

screws set aside prior to

Step 1.

The dishwasher

must be secured to the

countertop or the

cabinet

sides.

When countertops

are made of wood,

use Method 1. When

countertops are granite or

other materials that will not

accept screws, use

Method

2 to secure dishwasher at the sides.

IMPORTANT

–

Drive screws straight

and flush. Protruding

screw heads will

scratch the top or

sides of the control

panel and can interfere

with door closing.

Method 1

Secure dishwasher to wood countertop

• Fasten the dishwasher to the underside of the countertop

with the 2 Phillips special head screws provided.

Method 2

Secure dishwasher with side-mounting brackets

• Remove plug buttons (one on each side).

• Install screws through the dishwasher side mount bracket

and into the adjacent cabinet on each side. Reinstall plug

buttons.

Figure Y







Figure Z











Figure AA

Figure W

When step is complete, close dishwasher door and verify that

gap between countertop and top of dishwasher door is at

least 1/2".

Either Method

Figure X

2514C

Screws

Plug Buttons

Granite Countertop

Turn Legs

to Adjust

Countertop

Mounting

brackets

Side-Mounting

Bracket

Installation Instructions

STEP 12 CONNECT WATER SUPPLY

Connect water supply line to 90° elbow.

• Slide compression nut,

then ferrule over end of

water line.

• Insert water line into 90°

elbow.

• Slide ferrule against

elbow and secure with

compression nut.

Figure BB

Figure CC

STEP 13 CONNECT DRAIN LINE

FOLLOW ALL LOCAL CODES AND ORDINANCES.

The molded end of the drain hose will fit 5/8" through 1"

diameter inlet ports on the air gap, waste tee or disposer.

• Determine size of inlet port

• Cut drain hose connector on the marked line, if required, to ﬁ t

the inlet port.

• If a longer drain hose is required, add up to 42" of length for

a total of 10' to the factory installed hose. Use 5/8" or 7/8"

inside diameter hose and a coupler to

connect the two

hose ends.

Secure the

connection with

hose clamps.

Figure DD

• Secure the drain hose to the air gap, waste tee or disposer

with clamps.

Note:

TOTAL DRAIN HOSE LENGTH MUST NOT EXCEED 10' FOR

PROPER DRAIN OPERATION.

Waste Tee Installation

Figure EE





Disposer Installation

Waste Tee Installation

Figure FF

Disposer Installation

Method 2 – Drain Hose Routing

Route the drain hose of the dishwasher to a minimum height of 32" from

the ﬂ oor with the supplied hanger as shown.

IMPORTANT

– When connecting

drain line to disposer, check to be sure

that drain plug has been removed.

DISHWASHER WILL NOT DRAIN IF

PLUG IS LEFT IN PLACE.

Tip:

Avoid unnecessary service call charges. Always be sure

disposer drain plug has been removed before attaching

dishwasher drain hose to the disposer.

















18"

Min.

32"

Min.

05A-1183GG

Fasten drain hose at least at

32" height with hanger supplied

IMPORTANT

–

Either one of the above methods

must be used or dish

washer will not

operate

operly.

Method 1 – Air gap with waste tee or disposer

Insert the drain hose to air gap

s shown.

32"

Min.

18"

Min.

05A-1183FF

Fasten drain hose at least at

32" height with hanger supplied

IMPORTANT

– Check to be sure that door spring does

not rub or contact the fill hose or water supply line. Test by

opening and closing the door. Re-route the lines if a rubbing

noise or interference occurs.

DRAIN LINE INSTALLATION

• Connect drain line to air gap, waste tee or disposer using

either previously determined method.

Ferrule

90° Elbow

Compression Nu

Hot Water

Supply Line

Cutting Lines

3/4"

5/8"

IMPORTANT: Do not cut corrugated

portion of hose

Installation Instructions

STEP 14 CONNECT POWER SUPPLY

Skip this step if equipped with power cord.

Verify that power is turned off at the source.

• Remove junction box cover “A”.

• Locate the three dishwasher wires, (white, black and green)

with stripped ends. Insert dishwasher wires through the small

hole in the junction box “B”.

• Secure house wiring to the bottom of the junction box with a

strain relief “C”.

• Use wire nuts to connect incoming ground to green, white to

white and black to black “D”.

• Replace junction box cover “E”. Check to be sure that wires

are not pinched under the cover.

STEP 15 PRETEST CHECK LIST

Review this list after installing your dishwasher to avoid

charges for a service call that is not covered by your

warranty.

■

Check to be sure power is OFF.

■

Open door and remove all foam and paper packaging.

■

Locate the Owner’s Manual in the literature package.

■

Read the Owner’s Manual for operating instructions.

■

Check door opening and closing. If door does not open and

close freely or tends to fall, check spring adjustments. See

Step 1.

■

Check to be sure that wiring is secure under the dishwasher,

not pinched or in contact with door springs or other

components. See Step 9.

■

Check door alignment with tub. If door hits tub, level

dishwasher. See Step 10.

■

Pull lower rack out, about half way. Check to be sure it does

not roll back or forward on the door. If the rack moves,

adjust leveling legs. See Step 10.

■

Check door alignment with cabinet. If door hits cabinet,

reposition or relevel dishwasher. See Step 10.

■

Verify water supply and drain lines are not kinked or in

contact with other components. Contact with motor or

dishwasher frame could cause noise. See Step 8.

■

Turn on the sink hot water faucet and verify water

temperature. Incoming water temperature must

be between 120°F and 150°F. A minimum of 120°F

temperature is required for best wash performance. See

“Prepare Hot Water Line,” page 5.

■

Add 2 quarts of water to the bottom of the dishwasher to

lubricate the pump seal.

■

Turn on water supply. Check for leaks. Tighten connections

if needed.

■

Remove protective film if present from the control panel

and door.

■

Avoid service call charges by ensuring there is an air gap

or drain hose routed through the required 32" minimum

height.

Figure GG

#282 French

If house wiring is not 2-wire with ground, a

ground must be provided by the installer.

When house wiring is aluminum, be sure to

use UL Listed anti-oxidant compound and

aluminum-to-copper connectors

WARNING

White

Ground

Black

Check That White, Black and

Green Dishwasher Wires Are Threaded

Thru Hole in Back

Remove

Junction Box

Cover

Insert Power

Cord Wires Thru

Strain Relief

and Tighten

Use UL Listed

Wire Nuts

Installation Instructions

STEP 16 DISHWASHER WET TEST

■

Turn on power supply (or plug power cord into outlet,

if equipped).

■

Start the unit to check for leaks.

– Press ON/OFF button to turn unit on

– Press CYCLE SELECT button until light below RINSE cycle

illuminates

■

Close door.

■

Check to be sure that water enters the dishwasher. If water

does not enter the dishwasher, check to be sure that water

and power are turned on.

■

Check for leaks under the dishwasher. If a leak is found, turn

off power supply, then tighten connections. Restore power

after leak is corrected.

■

Check for leaks around the door. A leak around the door

could be caused by door rubbing or hitting against

adjacent cabinet. Reposition the dishwasher if necessary.

See Step 9.

■

The dishwasher will drain and turn off about 5 to 7 minutes

after the first fill. Check drain lines. If leaks are found,

turn power off at the breaker and correct plumbing as

necessary. Restore power after corrections are made. See

Step 12.

■

Open dishwasher door and make sure most of the water

has drained. If not, check that disposer plug has been

removed and/or air gap is not plugged. See Step 13. Also

check drain line for kinking.

■

Run the dishwasher through another fill and drain cycle.

Check for leaks and correct if required.

■

At the end of drain, open door and press ON/OFF button to

turn unit off.

Figure HH

STEP 17 REPLACE TOEKICK

• Place 2-piece toekick against the legs of the dishwasher.

• Place the inner toekick piece (with slots) against the toekick

bracket. The slots should align with toekick bracket screw

holes. Allow the toekick to touch the ﬂ oor.

• Place larger toekick over the inner piece and install 4 toekick

screws.

• Use additional 2 screws for installations over 33-1/2" high.

• Use both toekick pieces for all installation heights.

STEP 18 LITERATURE

• Be sure to leave complete literature package and Installation

Instructions with the consumer.

GE Consumer & Industrial

General Electric Company

Louisville, Kentucky 40225

ge.com

Pub. No. 31-

242

Dwg. No

206C

1559

180

2514

(

)

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

2-Piece Toekic

Adjust Up

or Down

Use Top 4

Screw Holes

GE Profile PDW1800KWW Guide d'installation

Marque: GE Profile

Modèle: PDW1800KWW

Catégorie: Lave-vaisselle

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: GE Profile PDW1800KWW Installation guide

GE Profile PDW1800KWW Guide d'installation

GE Profile PDW1800KWW Guide d'installation

dans d''autres langues

Autres documents