Ariston FDG 9620BS EX Mode d'emploi

Catégorie
Machines à laver
Taper
Mode d'emploi
1
GB
English,1
GB
WASHER-DRYER
! This symbol reminds you to read this instruc-
tion manual.
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 4
Cutting off the water and electricity supplies
Cleaning the washer-dryer
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and advice, 5
General safety
Disposal
Opening the porthole door manually
Description of the washer-dryer, 6-7
Control panel
Display
How to run a wash cycle or a drying cycle, 8
Wash cycles and options, 9
Table of programmes and wash cycles
Wash options
Detergents and laundry, 10
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Load balancing system
Troubleshooting, 11
Service, 12
FDG 9620
Instructions for use
Français,13
FR
AR
, 25
2
GB
Levelling the machine correctly will provide
it with stability, help to avoid vibrations and
excessive noise and prevent it from shifting
while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow
a sufficient ventilation space underneath the
washer-dryer.
Connecting the electricity and
water supplies
Connecting the water inlet hose
1. Connect the inlet
hose by screwing it to
a cold water tap using
a 3/4 gas threaded
connection (see
figure).
Before performing
the connection, allow
the water to run freely
until it is perfectly
clear.
2. Connect the
inlet hose to the
washer-dryer by
screwing it onto the
corresponding water
inlet of the appliance,
which is situated on
the top right-hand
side of the rear part
of the appliance (see
figure).
3. Make sure that the hose is not folded over
or bent.
! The water pressure at the tap must fall within
the range of values indicated in the Technical
data table (see next page).
! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
Installation
! This instruction manual should be kept in a
safe place for future reference. If the washer-
dryer is sold, transferred or moved, make
sure that the instruction manual remains with
the machine so that the new owner is able to
familiarise himself/herself with its operation
and features.
! Read these instructions carefully: they
contain vital information relating to the safe
installation and operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washer-dryer from its
packaging.
2. Make sure that the washer-dryer has not
been damaged during the transportation
process. If it has been damaged, contact the
retailer and do not proceed any further with
the installation process.
3. Remove the 4
protective screws
(used during
transportation)
and the rubber
washer with the
corresponding
spacer, located on
the rear part of the
appliance (see figure).
4. Close off the holes using the plastic plugs
provided.
5. Keep all the parts in a safe place: you will
need them again if the washer-dryer needs to
be moved to another location.
! Packaging materials should not be used as
toys for children.
Levelling
1. Install the washer-dryer on a flat sturdy floor,
without resting it up against walls, furniture
cabinets or anything else.
2. If the floor is
not perfectly level,
compensate for
any unevenness by
tightening or loosening
the adjustable front
feet (see figure); the
angle of inclination,
measured in relation to
the worktop, must not
exceed 2°.
3
GB
Connecting the drain hose
Connect the drain
hose, without bending
it, to a drain duct or
a wall drain situated
between 65 and 100
cm from the floor;
alternatively, placed
it over the edge
of a basin, sink or
tub, fastening the
duct supplied to
the tap (see figure).
The free end of the
hose should not be
underwater.
! We advise against the use of hose extensions;
if it is absolutely necessary, the extension must
have the same diameter as the original hose
and must not exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the
electricity socket, make sure that:
the socket is earthed and complies with all
applicable laws;
the socket is able to withstand the
maximum power load of the appliance as
indicated in the Technical data table (see
opposite);
the power supply voltage falls within the
values indicated in the Technical data table
(see opposite);
the socket is compatible with the plug of the
washer-dryer. If this is not the case, replace
the socket or the plug.
! The washer-dryer must not be installed
outdoors, even in covered areas. It is extremely
dangerous to leave the appliance exposed to
rain, storms and other weather conditions.
! When the washer-dryer has been installed, the
electricity socket must remain within easy reach.
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
65 - 100 cm
! The power supply cable must only be
replaced by authorised technicians.
Warning! The company shall not be held
responsible in the event that these standards
are not observed.
The first wash cycle
Once the appliance has been installed, and
before you use it for the first time, run a wash
cycle with detergent and no laundry, using
wash cycle auto clean (see “Cleaning the
washer-dryer).
Technical data
Model
FDG 9620
Dimensions
width 59.5 cm
height 85 cm
depth 60,5 cm
Capacity
from 1 to 9 kg for the wash
programme
from 1 to 6 kg for the drying
programme
Electrical
connections
please refer to the technical
data plate fixed to the machine
Water con-
nections
maximum pressure
1 MPa (10 bar)
minimum pressure
0.05 MPa (0.5 bar)
drum capacity 62 litres
Spin speed
up to 1200 rotations per
minute
Energy ra-
ted
programmes
according to
regulation
EN 50229
Wash: programme 5; tem-
perature 60°C; using a load
of 9 kg.
Drying: the smaller load
(3kg) must be dried by
selecting the “A4 (EXTRA)
dryness level. The load must
consist of 3 sheets, 2 pil-
lowcases and 1 hand towel;
the remainder of the load must
be dried by selecting the A4
(EXTRA) dryness level.
This appliance conforms to
the following EC Directives:
- 2004/108/EC (Electromagne-
tic Compatibility)
- 2006/95/EC (Low Voltage)
- 2012/19/EU (WEEE)
4
GB
Caring for the door and drum of
your appliance
Always leave the porthole door ajar in order
to prevent unpleasant odours from forming.
Cleaning the pump
The washer-dryer is fitted with a self-cleaning
pump which does not require any maintenance.
Sometimes, small items (such as coins or
buttons) may fall into the pre-chamber which
protects the pump, situated in its bottom part.
! Make sure the wash cycle has finished and
unplug the appliance.
To access the pre-chamber:
1. using a
screwdriver, remove
the cover panel on
the lower front part of
the washer-dryer (see
figure);
2. unscrew the lid
by rotating it anti-
clockwise (see figure):
a little water may
trickle out. This is
perfectly normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks
are securely in place before you push it onto
the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If
there are any cracks, it should be replaced
immediately: during the wash cycles, water
pressure is very strong and a cracked hose
could easily split open.
! Never use second-hand hoses.
Care and maintenance
Cutting off the water and
electricity supplies
Turn off the water tap after every wash cycle.
This will limit wear on the hydraulic system
inside the washer-dryer and help to prevent
leaks.
Unplug the washer-dryer when cleaning it
and during all maintenance work.
Cleaning the washer-dryer
• The outer parts and rubber components
of the appliance can be cleaned using a soft
cloth soaked in lukewarm soapy water. Do not
use solvents or abrasives.
• The washer-dryer has a “Auto Clean”
programme for its internal parts that must be
run with no load in the drum.
To help the wash cycle you may want to use
either the detergent (i.e. a quantity 10% the
quantity specified for lightly-soiled garments)
or special additives to clean the washer-
dryer. We recommend running a cleaning
programme every 40 wash cycles.
To start the programme press button A for 5
seconds (see figure).
The programme will start automatically and will
run for about 70 minutes. To stop the cycle
press the START/PAUSE button.
Cleaning the detergent dispenser
drawer
Remove the
dispenser by raising it
and pulling it out (see
figure).
Wash it under running
water; this operation
should be repeated
frequently.
1
2
A
5
GB
Precautions and tips
! This washer-dryer was designed and constructed in
accordance with international safety regulations. The
following information is provided for safety reasons and
must therefore be read carefully.
General safety
This appliance was designed for domestic use only.
This appliance can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved. Children
shall not play with the appliance. Cleaning and
user maintenance shall not be made by children
without supervision.
Do not dry unwashed items in the tumble dryer.
– Items that have been soiled with
substances such as cooking oil, acetone,
alcohol, petrol, kerosene, spot removers,
turpentine, waxes and wax removers should
be washed in hot water with an extra
amount of detergent before being dried in
the tumble dryer.
– Items such as foam rubber (latex foam),
shower caps, waterproof textiles, rubber
backed articles and clothes or pillows fitted
with foam rubber pads should not be dried in
the tumble dryer.
– Fabric softeners, or similar products,
should be used as specified by the fabric
softener instructions.
The final part of a tumble dryer cycle occurs
without heat (cool down cycle) to ensure that
the items are left at a temperature that ensures
that the items will not be damaged.
WARNING: Never stop a tumble dryer before
the end of the drying cycle unless all items
are quickly removed and spread out so that
the heat is dissipated.
Do not touch the machine when barefoot or with wet or
damp hands or feet.
Do not pull on the power supply cable when unplugging
the appliance from the electricity socket. Hold the plug
and pull.
Do not open the detergent dispenser drawer while the
machine is in operation.
Do not touch the drained water as it may reach
extremely high temperatures.
Never force the porthole door. This could damage the
safety lock mechanism designed to prevent accidental
opening.
If the appliance breaks down, do not under any
circumstances access the internal mechanisms in an
attempt to repair it yourself.
Always keep children well away from the appliance while
it is operating.
The door can become quite hot during the wash cycle.
If the appliance has to be moved, work in a group of two
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
Before loading laundry into the washer-dryer, make sure
the drum is empty.
During the drying phase, the door tends to get quite hot.
Do not use the appliance to dry clothes that
have been washed with flammable solvents
(e.g. trichlorethylene).
Do not use the appliance to dry foam rubber
or similar elastomers.
Make sure that the water tap is turned on during
the drying cycles.
Children of less than 3 years should be kept
away from the appliance unless continuou-
sly supervised.
Remove all objects from pockets such as
lighters and matches.
Disposal
Disposing of the packaging materials: observe local
regulations so that the packaging may be re-used.
The European Directive 2012/19/EU on Waste
Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected
separately in order to optimise the recovery and
recycling of the materials they contain and reduce
the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the
product reminds you of your obligation, that when
you dispose of the appliance it must be separately
collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
Opening the porthole door manually
In the event that it is not possible to open the porthole
door due to a powercut, and if you wish to remove the
laundry, proceed as follows:
1. remove the plug from the electrical socket.
2. make sure the water level inside the machine is lower
than the door opening; if it is not, remove excess water
using the drain hose, collecting it in a bucket as indicated
in the figure.
3. using a screwdriver, remove the cover panel on the
lower front part of the washer-dryer (see figure).
4. pull outwards using the tab as indicated in the figure,
until the plastic tie-rod is freed from its stop position; pull
downwards and open the door at the same time.
5. reposition the panel, making sure the hooks are securely
in place before you push it onto the appliance.
20
6
GB
Control panel
TEMPERATURE
button
WASH
CYCLE
SELECTOR
KNOB
Detergent dispenser drawer
ON/OFF
button
SPIN
button
START/PAUSE
button and indicator
light
DISPLAY
DRYING
button
OPTION
buttons and
indicator lights
Detergent dispenser drawer: used to dispense
detergents and washing additives (see “Detergents and
laundry”).
ON/OFF button: press this briefly to switch the
machine on or off. The START/PAUSE indicator light which
flashes slowly in a green colour shows that the machine
is switched on. To switch off the washer-dryer during the
wash cycle, press and hold the button for approximately 3
seconds; if the button is pressed briefly or accidentally the
machine will not switch off.
If the machine is switched off during a wash cycle, this
wash cycle will be cancelled.
WASH CYCLE SELECTOR KNOB: used to set the
desired wash cycle (see “Table of programmes and wash
cycles”).
OPTION buttons and indicator lights: press to select the
available options. The indicator light corresponding to the
selected option will remain lit.
CLEANING ACTION
button : to select the desired
wash intensity.
TEMPERATURE button: press to reduce or completely
exclude the temperature; the value appears on the display.
SPIN button: press to reduce or completely exclude
the spin cycle; the value appears on the display.
DRYING button : press to decrease or exclude drying;
the selected drying level or time will appear on the display.
START/PAUSE button and indicator light: when the green
indicator light flashes slowly, press the button to start a
wash cycle. Once the cycle has begun the indicator light
will remain lit in a fixed manner. To pause the wash cycle,
press the button again; the indicator light will flash in an
amber colour. If the symbol is not illuminated, the door
may be opened. To start the wash cycle from the point at
which it was interrupted, press the button again.
CHILD LOCK button: to activate the control panel lock,
press and hold the button for approximately 2 seconds.
When the symbol is illuminated, the control panel
is locked (apart from the ON/OFF button). This means it
is possible to prevent wash cycles from being modified
accidentally, especially where there are children in the
home. To deactivate the control panel lock, press and hold
the button for approximately 2 seconds.
Standby mode
This washer-dryer, in compliance with new energy saving
regulations, is fitted with an automatic standby system
which is enabled after about 30 minutes if no activity is
detected. Press the ON-OFF button briefly and wait for the
machine to start up again.
Consumption in off-mode: 0,5 W
Consumption in Left-on: 8 W
CLEANING
ACTION
button
CHILD
LOCK
button
Description of the washer-dryer
7
GB
Display
The display is useful when programming the machine and provides a great deal of information.
The duration of the available wash cycles and the remaining time of a running cycle appear in section A (the display will show
the maximum duration of the cycle chosen, which may decrease after several minutes, since the effective duration of the
programme varies depending on the wash load and the settings chosen); if the DELAYED START option has been set, the
countdown to the start of the selected wash cycle will appear.
Moreover, pressing the relative button allows for visualising the maximum values for the temperature, spin speed or type of
drying relative to the selected programme or the most recently selected ones, if compatible with the selected programme.
The “wash cycle phases” corresponding to the selected wash cycle and the “wash cycle phase” of the running wash cycle
appear in section B:
Main wash
Rinse
Spin/Pump out
Drying
The icons corresponding to “temperature”, “spin” and “drying” (working from the left) are displayed in section C.
The “temperature” bars indicate the maximum temperature level which may be selected for the set cycle.
The “spin” bars indicate the maximum spin level which may be selected for the set cycle.
The symbol lights up while the drying settings are being adjusted.
DOOR LOCKED indicator light:
The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before opening the door.
To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED symbol is switched
off the door may be opened.
B
C
A
8
GB
How to run a wash cycle or a
drying cycle
1. SWITCH THE MACHINE ON. Press the button; the
START/PAUSE indicator light will flash slowly in a green colour.
2. LOAD THE LAUNDRY. Open the porthole door. Load
the laundry, making sure you do not exceed the maximum
load value indicated in the table of programmes and wash
cycles on the following page.
3. MEASURE OUT THE DETERGENT. Pull out the
detergent dispenser drawer and pour the detergent into
the relevant compartments as described in “Detergents
and laundry”.
4. CLOSE THE DOOR.
5. SELECT THE WASH CYCLE. Use the WASH CYCLE
SELECTOR knob to select the desired wash cycle. A
temperature and spin speed is set for each wash cycle;
these values may be adjusted. The duration of the cycle will
appear on the display.
6. CUSTOMISE THE WASH CYCLE. Use the relevant buttons:
Modify the temperature and/or spin speed. The machine
automatically displays the maximum temperature and spin
speed values set for the selected cycle, or the most recently-
used settings if they are compatible with the selected cycle. The
temperature can be decreased by pressing the button, until
the cold wash “OFF” setting is reached. The spin speed may
be progressively reduced by pressing the button, until it is
completely excluded (theOFF setting). If these buttons are
pressed again, the maximum values are restored.
! Exception: if the
4
programme is selected, the temperature
can be increased up to a value of 90°C (+ prewash).
Setting the drying cycle
The first time the button is pressed, the machine will
automatically select the maximum drying cycle which is
compatible with the selected wash cycle. Subsequent
presses will decrease the drying level and then the drying
time, until the cycle is excluded completely (“OFF”).
Drying may be set as follows:
A- Based on the desired laundry dryness level:
Iron “A1”: suitable for clothes which will need ironing
afterwards. the remaining dampness softens creases,
making them easier to remove.
Hanger A2”: ideal for clothes which do not need to be dried fully.
Cupboard “A3”: suitable for laundry which can be put
back in a cupboard without being ironed.
Extra “A4”: suitable for garments which need to be dried
completely, such as sponges and bathrobes.
B - Based on a set time period: between 30 and 180 minutes.
If your laundry load to be washed and dried is much
greater than the maximum stated load, perform the wash
cycle, and when the cycle is complete, divide the garments
into groups and put some of them back in the drum. At this
point, follow the instructions provided for a “Drying only
cycle. Repeat this procedure for the remainder of the load.
A cooling-down period is always added to the end of each
drying cycle.
Drying only
Use the cycle selector knob to select a drying cycle (12-13-14)
in accordance with the type of fabric. The desired drying level or
time may also be set using the DRYING button .
Selecting the cotton drying cycle through the programme
selector knob and pressing the “Eco” button activates an
automatic drying cycle that allows for saving energy, thanks
to an optimal combination of air temperature and cycle
duration; the display will visualise the “A2” dryness level.
Set the desired wash intensity.
Option makes it possible to optimise washing based
on the level of soil in the fabrics and on desired wash cycle
intensity.
Select the wash programme: the cycle will be automatically
set to “Normal” as optimised for garments with an average
level of soil (this setting is not applicable to the “Wool”
cycle, which is automatically set to “Delicate”).
For heavily-soiled garments press button until the
Intensive level is reached. This level ensures a high-
performance wash due to a larger quantity of water used
in the initial phase of the cycle and due to increased drum
rotation. It is useful when removing the most stubborn stains.
It can be used with or without bleach. If you desire bleaching,
insert the extra tray compartment (4) into compartment 1.
When pouring in the bleach, be careful not to exceed the
“max” level marked on the central pivot (see figure pag. 10).
For lightly-soiled garments or a more delicate treatment
of the fabrics, press button until the “Delicate” level
is reached. The cycle will reduce drum rotation to ensure
washing results that are perfect for delicate garments.
Modify the cycle settings.
Press the button to enable the option; the indicator light
corresponding to the button will switch on.
Press the button again to disable the option; the
indicator light will switch off.
! If the selected option is not compatible with the set wash
cycle, the indicator light will flash and the option will not be
activated.
! If the selected option is not compatible with a previously
selected one, the indicator light corresponding to the first
function selected will flash and only the second option will
be activated; the indicator light for the option which has been
activated will be illuminated.
! The options may affect the recommended load value and/
or the duration of the cycle.
7. START THE WASH CYCLE. Press the START/PAUSE
button. The corresponding indicator light will turn green,
remaining lit in a fixed manner, and the door will be locked
(the DOOR LOCKED symbol will be lit). To change
a wash cycle while it is in progress, pause the washer-
dryer using the START/PAUSE button (the START/PAUSE
indicator light will flash slowly in an amber colour); then
select the desired cycle and press the START/PAUSE
button again. To open the door while a cycle is in progress,
press the START/PAUSE button; if the DOOR LOCKED
symbol is switched off the door may be opened. Press
the START/PAUSE button again to restart the wash cycle
from the point at which it was interrupted.
8. THE END OF THE WASH CYCLE. This will be indicated
by the text “END” on the display; when the DOOR LOCKED
symbol switches off the door may be opened. Open the
door, unload the laundry and switch off the machine.
! If you wish to cancel a cycle which has already begun, press
and hold the button. The cycle will be stopped and the
machine will switch off.
9
GB
Wash cycles and options
Wash options
! If the selected option is not compatible with the set
wash cycle, the indicator light will flash and the option will
not be activated.
! If the selected option is not compatible with a previously
selected one, the indicator light corresponding to the first
function selected will flash and only the second option will be
activated; the indicator light for the option which has been
activated will be illuminated.
Eco
The Eco option saves energy by not heating the water
used to wash your laundry – an advantage both to the
environment and to your energy bill. Instead, intensified
wash action and water optimisation ensure great wash
results in the same average time of a standard cycle.
For the best washing results we recommend the usage of
a liquid detergent.
By selecting the drying function as well, an automatic
drying cycle automatically activates at the end of the
wash cycle – it too allows for saving energy, thanks to the
optimal combination of air temperature and cycle duration.
! It can be activated with programme 4.
Table of programmes and wash cycles
For all Test Institutes:
1) Test wash cycle in compliance with regulation EN 50229: set wash cycle 5 with a temperature of 60°C.
2) Long wash cycle for cottons: set wash cycle 5 with a temperature of 40°C.
Delay Timer
To set a delayed start for the selected cycle, press the
corresponding button repeatedly until the required delay
period has been reached. When this option is enabled, the
corresponding indicator light will remain lit. To remove the
delayed start setting, press the button until the text “OFF”
appears on the display.
Wash cycles
Description of the wash cycle
Max.
temp.
(°C)
Max.
speed
(rpm)
Drying
Detergents
Max. load
(kg)
Cycle
duration
Pre-
wash
Wash Bleach
Fabric
softener
CLEAN Plus
1
Anti Stain
40° 1200
-
-
5
2
Anti Stain Quick
40° 1200
-
-
4,5
3
Whites
60° 1200
-
-
5
4
Cotton: heavily soiled whites and delicate colours. 60° 1200
-
9
4
Cotton (+ prewash): extremely soiled whites.
**
90° 1200
-
9
5
Standard Cotton (1): heavily soiled whites and delicate colours. 60° 1200
-
-
9
5
Standard Cotton (2): lightly soiled whites and delicate colours. 40° 1200
-
-
9
6
Synthetics: heavily soiled resistant colours. 60° 800
-
4
SPECIALS
7
Anti allergy
60° 1200
-
5
8
Wool: for wool, cashmere, etc. 40° 800
-
-
2
9
Delicates
30° 0
-
-
1
10
Fast Wash 30’: to refresh lightly soiled garments quickly (not suitable for
wool, silk and clothes which require washing by hand).
30° 800
-
-
-
3,5
11
Wash & Dry 45’
30° 1200
-
-
1
DRYING
12
Cotton
- -
- - - - 6
13
Synthetics
- -
- - - - 4
14
Wool
- -
- - - - 2
Partials Programmes
Rinse - 1200
- - -
9
Spin+Pump out - 1200
- - - - 9
Pump out only *
- OFF - - - - - 9
The duration of the wash cycles can be checked on the display.
* If you select programme and exclude the spin cycle, the machine will drain only.
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-
ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
** If the temperature exceeds 60°C, the option cannot be started.
10
GB
Detergents and laundry
Detergent dispenser drawer
Successful washing results also depend on the correct
dose of detergent: adding too much detergent will not
necessarily result in a more efficient wash, and may in
fact cause build up on the inside of your appliance and
contribute to environmental pollution.
! Do not use hand washing detergents; they create too
much foam.
Open the detergent
dispenser drawer and pour
in the detergent or washing
additive, as follows.
compartment 1: Pre-
wash detergent (powder)
Before pouring in the
detergent, make sure that
extra compartment 4 has
been removed.
compartment 2:
Detergent for the wash cycle (powder or liquid)
If liquid detergent is used, it is recommended that the removable
plastic partition A (supplied) be used for proper dosage. If
powder detergent is used, place the partition into slot B.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
extra compartment 4: Bleach
Preparing the laundry
Divide the laundry according to:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
Empty all garment pockets and check the buttons.
Do not exceed the listed values, which refer to
the weight of the laundry when dry: see “Table of
programmes and wash cycles”.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1,200 g
1 towel 150-250 g
Special wash cycles
Anti Stain: the programme 1 is suitable to heavily-soiled
garments with resistant colours. It ensures a washing class
that is higher than the standard class (A class).
When running the programme, do not mix garments of
different colours. We recommend the use of powder
detergent. Pre-treatment with special additives is
recommended if there are obstinate stains.
If the drying function is selected, a drying cycle
automatically activates at the end of the wash cycle that
resembles open-air drying, with the added advantages
of preserving garments from yellowing due to sunlight
exposure and preventing loss of whiteness caused by
the possible presence of dust in the air. Drying cycles
can only be selected on a level basis. Dryness level “A2
recommended.
Anti Stain Quick: this programme is ideal for washing
the most difficult daily stains in 1 hour. It is ideal for mixed
fabrics and coloured garments, caring for your clothes as
it washes.
M
AX
1
2
4
3
A
B
If the drying function is selected, a drying cycle automatically
activates at the end of the wash cycle that resembles open-
air drying, with the added advantages of preserving garments
from yellowing due to sunlight exposure and preventing loss
of whiteness caused by the possible presence of dust in
the air. Drying cycles can only be selected on a level basis.
Dryness levelA2recommended.
Whites: use this cycle 3 to wash white clothes. The
programme is designed to maintain the brightness of white
clothes over time. Use powder detergent for best results.
If the drying function is selected, a drying cycle automatically
activates at the end of the wash cycle that resembles open-
air drying, with the added advantages of preserving garments
from yellowing due to sunlight exposure and preventing loss
of whiteness caused by the possible presence of dust in the
air. Drying cycles can only be selected on a level basis.
Anti allergy: use programme 7 to remove major allergens
such as pollen, mites, cat’s and dog’s hair.
Wool - Woolmark Apparel Care - Green:
the wool wash cycle of this machine has been approved
by The Woolmark Company for the washing of wool
garments labelled as “hand wash” provided that the
products are washed according to the instructions on the
garment label and those issued by the manufacturer of this
washing machine (M1127)
Delicates: use programme 9 to wash very delicate
garments having strasses or sequins.
To wash silk garments and curtains select the cycle 9 and
set the “Delicate” level from option .
We recommend turning the garments inside out before
washing and placing small items into the special bag
for washing delicates. Use liquid detergent on delicate
garments for best results.
When selecting an exclusively time-based drying function,
a drying cycle is performed at the end of the wash cycle
that is particularly delicate, thanks to light handling and
appropriate temperature control of the water jet.
The recommended durations are:
1 kg of synthetic garments --> 150 min
1 kg of synthetic and cotton garments --> 180 min
1 kg of cotton garments --> 180 min
The degree of dryness depends on the load and fabric
composition.
Wash & Dry 45’ select programme 11 for washing and
drying lightly soiled garments (Cotton and Synthetic) in a
short time. This cycle may be used to wash and dry a
laundry load of up to 1 kg in just 45 minutes. To achieve
optimum results, use liquid detergent and pre-treat cuffs,
collars and stains.
Load balancing system
Before every spin cycle, to avoid excessive vibrations
before every spin and to distribute the load in a uniform
manner, the drum rotates continuously at a speed which
is slightly greater than the washing rotation speed. If,
after several attempts, the load is not balanced correctly,
the machine spins at a reduced spin speed. If the load is
excessively unbalanced, the washer-dryer performs the
distribution process instead of spinning. To encourage
improved load distribution and balance, we recommend
small and large garments are mixed in the load.
11
GB
Troubleshooting
Your washer-dryer could occasionally fail to work. Before contacting the Technical Assistance Service (see “ Service”), make
sure that the problem cannot be solved easily using the following list.
Problem:
The washer-dryer does not switch
on.
The wash cycle does not start.
The washer-dryer does not fill
with water (the text “H2O” flashes
on the display).
The washer-dryer continuously
takes in and drains water.
The washer-dryer does not drain
or spin.
The washer-dryer vibrates a lot
during the spin cycle.
The washer-dryer leaks.
The “option and START/PAUSE
indicator lights flash rapidly and an
error code appears on the display (e.g.:
F-01, F-..).
There is too much foam.
The washer-dryer does not dry.
Possible causes / Solutions:
The appliance is not plugged into the socket fully, or not enough to make contact.
There is no power in the house.
The washer-dryer door is not closed properly.
The ON/OFF button has not been pressed.
The START/PAUSE button has not been pressed.
The water tap has not been opened.
A delayed start has been set.
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap has not been opened.
There is no water supply in the house.
The pressure is too low.
The START/PAUSE button has not been pressed.
The drain hose is not fitted at a height between 65 and 100 cm from the floor
(see “Installation”).
The free end of the hose is under water (see “Installation”).
The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, turn off the water tap, switch the
appliance off and contact the Technical Assistance Service. If the dwelling is on one
of the upper floors of a building, there may be problems relating to water drainage,
causing the washer-dryer to fill with water and drain continuously. Special anti-
draining valves are available in shops and help to prevent this inconvenience.
The wash cycle does not include draining: some cycles require the draining
process to be enabled manually.
The drain hose is bent (see “Installation”).
The drainage duct is clogged.
The drum was not unlocked correctly during installation (see “Installation”).
The washer-dryer is not level (see “Installation”).
The washer-dryer is trapped between cabinets and walls (see “Installation”).
The water inlet hose is not screwed on properly (see “Installation”).
The detergent dispenser drawer is blocked (for cleaning instructions, see “Care
and maintenance”).
The drain hose is not fixed properly (see “Installation”).
Switch off the machine and unplug it, wait for approximately 1 minute and then
switch it back on again.
If the problem persists, contact the Technical Assistance Service.
The detergent is not suitable for machine washing (it should display the text
“for washing machine” or “hand and machine wash”, or the like).
Too much detergent was used.
The appliance is not plugged into the socket, or not enough to make contact.
There has been a power failure.
The appliance door is not shut properly.
A DELAY TIMER has been set.
DRYING is in the OFF position.
12
GB
Service
Before contacting the Technical Assistance Service:
Check whether you can solve the problem alone (see “Troubleshooting”);
Restart the wash cycle to check whether the problem has been solved;
If this is not the case, contact an authorised Technical Assistance Centre.
! Always request the assistance of authorised technicians.
Have the following information to hand:
the type of problem;
the appliance model (Mod.);
the serial number (S/N).
This information can be found on the data plate applied to the rear of the washer-dryer, and can also be found on the front of
the appliance by opening the door.
FR
13
LAVANTE SÉCHANTE
! Ce symbole vous rappelle de lire ce mode
d’emploi.
Sommaire
Installation, 14-15
Déballage et mise à niveau
Raccordements eau et électricité
Premier cycle de lavage
Caractéristiques techniques
Entretien et soin, 16
Coupure de l’arrivée d’eau et du courant
Nettoyage du lavante-séchante
Nettoyage du tiroir à produits lessiviels
Entretien du hublot et du tambour
Nettoyage de la pompe
Contrôle du tuyau d’arrivée de l’eau
Précautions et conseils, 17
Sécurité générale
Mise au rebut
Ouverture manuelle du hublot
Description du lavante-séchante, 18-19
Bandeau de commandes
Écran
Comment effectuer un cycle de lavage ou
un séchage, 20
Programmes et options, 21
Tableau des programmes
Options de lavage
Produits lessiviels et linge, 22
Tiroir à produits lessiviels
Triage du linge
Programmes spéciaux
Système d’équilibrage de la charge
Anomalies et remèdes, 23
Assistance, 24
FDG 9620
Mode d’emploi
Français
FR
14
FR
Installation
! Conserver ce mode d’emploi pour pouvoir
le consulter à tout moment. En cas de vente,
de cession ou de déménagement, veiller à ce
qu’il suive toujours le lavante-séchante pour
que son nouveau propriétaire soit informé sur
son mode de optionnement et puisse profiter
des conseils correspondants.
! Lire attentivement les instructions: elles
fournissent des conseils importants sur
l’installation, l’utilisation et la sécurité de
l’appareil.
Déballage et mise à niveau
Déballage
1. Déballer le lavante-séchante.
2. Contrôler que le lavante-séchante n’a pas
été endommagé pendant le transport. S’il est
abîmé, ne pas le raccorder et contacter le
vendeur.
3. Enlever les 4 vis
de protection servant
au transport, le
caoutchouc et la cale,
placés dans la partie
arrière (voir figure).
4. Boucher les trous à l’aide des bouchons
plastique fournis.
5. Conserver toutes ces pièces: il faudra les
remonter en cas de transport du lavante-
séchante.
! Les pièces d’emballage ne sont pas des
jouets pour enfants.
Mise à niveau
1. Installer le lavante-séchante sur un sol plat
et rigide, sans l’appuyer contre des murs, des
meubles ou autre.
2. Si le sol n’est pas
parfaitement horizontal,
visser ou dévisser les
pieds de glage avant
(voir figure) pour niveler
l’appareil; son angle
d’inclinaison, mesu
sur le plan de travail, ne
doit pas passer 2°.
Une bonne mise à niveau garantit la stabilité
de l’appareil et évite qu’il y ait des vibrations,
du bruit et des déplacements en cours de
optionnement. Si la machine est posée sur de
la moquette ou un tapis, régler les pieds de
manière à ce qu’il y ait suffisamment d’espace
pour assurer une bonne ventilation.
Raccordements eau et électricité
Raccordement du tuyau d’arrivée de
l’eau
1. Reliez le tuyau
d’alimentation en le
vissant à un robinet
d’eau froide à embout
fileté 3/4 gaz (voir
figure).
Faire couler l’eau
jusqu’à ce qu’elle
soit limpide et sans
impuretés avant de
raccorder.
2. Raccorder le tuyau
d’arrivée de l’eau au
lavante-séchante en
le vissant à la prise
d’eau prévue, dans la
partie arrière en haut
à droite (voir figure).
3. Attention à ce que le tuyau ne soit pas plié
ou écrasé.
! La pression de l’eau doit être comprise entre
les valeurs indiquées dans le tableau des
Caractéristiques techniques (voir page ci-
contre).
! Si la longueur du tuyau d’alimentation ne
suffit pas, s’adresser à un magasin spécialisé
ou à un technicien agréé.
! N’utiliser que des tuyaux neufs.
! Utiliser ceux qui sont fournis avec l’appareil.
FR
15
Raccordement du tuyau de vidange
Raccorder le tuyau
d’évacuation, sans
le plier, à un conduit
d’évacuation ou
à une évacuation
murale placés à
une distance du sol
comprise entre 65 et
100 cm ;
ou bien l’accrocher
à un évier ou à une
baignoire, dans ce
cas, fixer le support
en plastique fourni
avec l’appareil au
robinet (voir figure).
L’extrémité libre du
tuyau d’évacuation
ne doit pas être
plongée dans l’eau.
! L’utilisation d’un tuyau de rallonge est
absolument déconseillée mais si on ne peut
faire autrement, il faut absolument qu’il ait le
même diamètre que le tuyau original et sa
longueur ne doit pas dépasser 150 cm.
Raccordement électrique
Avant de brancher la fiche dans la prise de
courant, s’assurer que :
la prise est bien reliée à la terre et est
conforme aux réglementations en vigueur;
la prise est bien apte à supporter la
puissance maximale de l’appareil indiquée
dans le tableau des Caractéristiques
techniques (voir ci-contre);
la tension d’alimentation est bien comprise
entre les valeurs figurant dans le tableau des
Caractéristiques techniques (voir ci-contre);
la prise est bien compatible avec la fiche du
lavante-séchante. Autrement, remplacer la
prise ou la fiche.
! Le lavante-séchante ne doit pas être
installé dehors, même à l’abri, car il est très
dangereux de le laisser exposé à la pluie et
aux orages.
! Après installation du lavante-séchante,
la prise de courant doit être facilement
accessible.
! N’utiliser ni rallonges ni prises multiples.
! Le câble ne doit être ni plié ni trop écrasé.
! Le câble d’alimentation ne doit être remplacé
que par des techniciens agréés.
65 - 100 cm
Attention! Nous déclinons toute responsabilité
en cas de non-respect des normes
énumérées ci-dessus.
Premier cycle de lavage
Avant la première mise en service de l’appareil,
effectuer un cycle de lavage avec un produit
lessiviel mais sans linge et sélectionner le
programme «Auto nettoyage» (voirNettoyage
du lavante-séchante”).
Caractéristiques techniques
Modèle
FDG 9620
Dimensions
largeur 59,5 cm
hauteur 85 m
profondeur 60,5 cm
Capacité
de 1 à 9 kg pour le lavage
de 1 à 6 kg pour le séchage
Raccorde-
ments élec-
triques
Voir la plaque signalétique
appliquée sur la machine
Raccor-
dements
hydrauli-
ques
pression maximale 1 MPa
(10 bar) pression minimale
0,05 MPa (0,5 bar) capacité
du tambour 62 litres
Vitesse
d’essorage
jusqu’à 1200 tours minute
Programmes
de contrô-
le selon la
norme
EN 50229
lavage: programme 5; tem-
pérature 60°C; effectué avec
une charge de 9 kg.
séchage: pour le séchage
de la charge de linge réduite
(3kg), sélectionner le niveau
de séchage “A4” (Intensif),
le linge doit comprendre: 3
draps, 2 taies d’oreiller et 1
serviette de toilette;
pour le séchage de la char-
ge de linge restante, sélec-
tionner le niveau de séchage
“A4” (Intensif).
Cet appareil est conforme
aux Directives Communautai-
res suivantes:
- 2004/108/CE (Compatibili-
té électromagnétique)
- 2006/95/CE (Basse Tension)
- 2012/19/EU (WEEE)
16
FR
Entretien et soin
Coupure de l’arrivée d’eau et du
courant
Fermer le robinet de l’eau après chaque
lavage. Cela réduit l’usure de l’installation
hydraulique du lavante-séchante et évite tout
danger de fuites.
brancher la fiche de la prise de courant
lors de tout nettoyage du lavante-chante et
pendant tous les travaux d’entretien.
Nettoyage du lavante-séchante
• Pour nettoyer l’extérieur et les parties en
caoutchouc, utiliser un chiffon imbibé d’eau
tiède et de savon. N’utiliser ni solvants ni
abrasifs.
• Ce lavante-séchante est équipé d’un
programme «Auto nettoyage» des parties
internes qui doit être effectué tambour
complètement vide.
La lessive (dans une quantité égale à 10% de
celle conseillée pour du linge peu sale) ou les
additifs spéciaux pour le nettoyage du lavante-
séchante, pourront être utilisés comme
adjuvants dans le programme de lavage. Il
est conseillé d’effectuer le programme de
nettoyage tous les 40 cycles de lavage.
Pour activer le programme, appuyer sur la
touche A pendant 5
secondes (voir figure).
Le programme
démarrera
automatiquement
et durera environ 70
minutes. Pour stopper
le cycle, appuyer sur
la touche START/
PAUSE.
Nettoyage du tiroir à produits
lessiviels
Soulever le tiroir et le
tirer vers soi pour le
sortir de son logement
(voir figure).
Le laver à l’eau
courante; effectuer
cette opération assez
souvent.
Entretien du hublot et du tambour
Il faut toujours laisser le hublot entrouvert
pour éviter la formation de mauvaise odeurs.
Nettoyage de la pompe
Le lavante-séchante est équipé d’une pompe
autonettoyante qui n’exige aucune opération
d’entretien. Il peut toutefois arriver que de
menus objets (pièces de monnaie, boutons)
tombent dans la préchambre qui protège la
pompe, placée en bas de cette dernière.
! S’assurer que le cycle de lavage est bien
terminé et débrancher la fiche.
Pour accéder à cette préchambre:
1. démonter le
panneau situé à
l’avant du lavante-
séchante à l’aide d’un
tournevis (voir figure);
2. dévisser le
couvercle en le
tournant dans le sens
inverse des aiguilles
d’une montre (voir
figure): il est normal
qu’un peu d’eau
s’écoule;
3. nettoyer soigneusement l’intérieur;
4. revisser le couvercle;
5. remonter le panneau en veillant à bien
enfiler les crochets dans les fentes prévues
avant de le pousser contre l’appareil.
Contrôle du tuyau darrivée de l’eau
Contrôler le tuyau d’alimentation au moins
une fois par an. Procéder à son remplacement
en cas de craquèlements et de fissures: car
les fortes pressions subies pendant le lavage
pourraient provoquer des cassures.
! N’utiliser que des tuyaux neufs.
1
2
A
FR
17
Précautions et conseils
Ouverture manuelle du hublot
A défaut de pouvoir ouvrir la porte hublot à cause d’une panne
de courant pour étendre le linge, proder comme suit :
1. débrancher la fiche de la prise de courant.
2. s’assurer que le niveau de l’eau à l’intérieur de l’appareil
se trouve bien au-dessous de l’ouverture du hublot, si ce
n’est pas le cas vider l’eau en excès à travers le tuyau de
vidange dans un seau comme illustré voir figure.
3. démonter le panneau situé à l’avant du lavante-
séchante à l’aide d’un tournevis (voir figure).
4. se servir de la languette indiquée, tirer vers soi jusqu’à
ce que le tirant en plastique se dégage de son cran d’arrêt;
tirer ensuite vers le bas et ouvrir l’hublot en même temps.
5. remonter le panneau en veillant à bien enfiler les
crochets dans les fentes prévues avant de le pousser
contre l’appareil.
! Ce lavante-chante a été conçu et fabriqué conformément
aux normes internationales de sécurité. Ces consignes sont
fournies pour des raisons de sécuri, il faut les lire attentivement.
Sécurité générale
• Cet appareil est conçu pour un usage domestique.
Cet appareil peut être utilisé par les enfants
à partir de 8 ans et par les personnes dont
les capacités physiques, sensorielles ou
mentales sont réduites ou qui ne disposent
pas des connaissances suffisantes, à
condition qu’ils soient encadrés ou aient été
formés de façon appropriée pour l’utilisation
de l’appareil de façon sûre et en comprenant
les dangers qui y sont liés. Les enfants ne
doivent pas jouer avec l’appareil. L’entretien
et le nettoyage ne doivent pas être effectués
par les enfants sans surveillance.
- Ne pas mettre sécher du linge non lavé.
- Le linge contaminé avec des substances
telles que de l’huile de cuisson, de
l’acétone, de l’alcool, de l’essence, du
kérosène, des détachants, de l’essence de
térébenthine, de la cire et des substances
pour l’enlever, doit être lavé à l’eau chaude
avec une dose supplémentaire de lessive
avant d’être introduit dans le sèche-linge.
- Des objets en mousse expansée (mousse
de latex), des bonnets de douche, des textiles
imperméables, des articles doublés de
caoutchouc et des vêtements ou des coussins
ayant des parties en mousse de latex ne
doivent pas être cs en sèche-linge.
- En cas d’utilisation d’assouplissants ou
de tout autre produit similaire, se conformer
aux instructions du fabricant.
- La partie finale d’un cycle du sèche-linge se
produit sans chaleur (cycle de refroidissement)
pour éviter tout endommagement du linge.
ATTENTION: Ne jamais arrêter le sèche-linge
avant la fin du programme de séchage. Dans
ce cas, sortir immédiatement tout le linge et
l’étendre pour le faire refroidir rapidement.
Cet appareil est conçu pour un usage domestique.
Ne jamais toucher l’appareil si l’on est pieds nus et si
les mains sont mouillées ou humides.
Ne jamais tirer sur le câble pour débrancher la fiche de
la prise de courant.
Ne pas toucher à l’eau de vidange, elle peut atteindre
des températures très élevées.
Ne pas forcer pour ouvrir la porte hublot : le verrouillage
de sécurité qui protège contre les ouvertures
accidentelles pourrait s’endommager.
En cas de panne, éviter à tout prix d’accéder aux
mécanismes internes pour tenter une réparation.
Veiller à ce que les enfants ne s’approchent pas de
l’appareil pendant son fonctionnement.
Deux ou trois personnes sont nécessaires pour le
déplacer en faisant très attention. Ne jamais le déplacer
tout seul car il est très lourd.
Avant d’introduire le linge, s’assurer que le tambour est
bien vide.
Pendant le chage, le hublot a tendance à chauffer.
Ne mettez pas à sécher du linge la avec des
solvants inflammables (trichlothyne par ex.).
Ne mettez pas à sécher du caoutchouc-
mousse ou des élastomères du même genre.
20
Vérifiez qu’au cours du séchage, le robinet de l’eau soit
bien ouvert.
les enfants de moins de 3 ans doivent être
tenus à bonne distance du sèche-linge s’ils
ne sont pas sous surveillance constante.
Enlever tous les objets des poches,
notamment les briquets et les allumettes.
Mise au rebut
Mise au rebut du matériel d’emballage: se conformer
aux réglementations locales de manière à ce que les
emballages puissent être recyclés.
La Directive Européenne 2012/19/EU sur leschets
des Equipements Electriques et Electroniques, exige que
les appareils ménagers usagés ne soient pas jetés dans
le flux normal des déchets municipaux. Les appareils
usagés doivent être collectés parément afin d’optimiser
le taux decuration et le recyclage des matériaux qui
les composent et réduire l’impact sur la san humaine et
l’environnement. Le symbole de la ‘’poubelle barrée’ est
apposée sur tous les produits pour rappeler les obligations
de collecte pae. Les consommateurs devront contacter
les autorités locales ou leur revendeur concernant la
marche à suivre pour l’enlèvement de leur vieil appareil.
18
FR
Description du lavante-séchante
Bandeau de commandes
Touche
TEMPÉRATURE
BOUTON
PROGRAMMES
Tiroir à produits lessiviels
Touche ON/OFF
Touche
ESSORAGE
Touche et voyant
START/PAUSE
Ecran
Touches et voyants
OPTION
Tiroir à produits lessiviels : pour charger les produits
lessiviels et les additifs (voir “Produits lessiviels et linge”).
Touche ON/OFF : appuyer brièvement sur la touche
pour allumer ou éteindre l’appareil. Le voyant vert START/
PAUSE clignotant lentement indique que la machine est
allumée. Pour éteindre le lavante-séchante en cours
de lavage, appuyer sur la touche pendant au moins 3
secondes de suite ; une pression brève ou accidentelle
n’entraîne pas l’arrêt de l’appareil. L’arrêt de l’appareil
pendant un lavage annule le lavage en cours.
BOUTON PROGRAMMES: pour sélectionner le
programme désiré (voir “Tableau des programmes”).
Touches et voyants OPTION: pour sélectionner les
options disponibles. Le voyant correspondant à l’option
sélectionnée restera allumé.
Touche
INTENSITE DE LAVAGE
: appuyer pour
sélectionner l’intensité de lavage désirée.
Touche TEMPÉRATURE : appuyer sur cette
touche pour diminuer la température ou pour l’exclure
complètement. La valeur correspondante s’affiche à
l’écran.
Touche ESSORAGE : appuyer sur cette touche
pour diminuer la vitesse de l’essorage ou pour l’exclure
complètement. La valeur correspondante s’affiche à
l’écran.
Touche
S
ÉCHAGE : appuyer pour réduire ou
supprimer le séchage; le niveau ou le temps de séchage
sélectionné s’affiche à l’écran.
Touche avec voyant START/PAUSE: quand le voyant vert
clignote lentement, appuyer sur la touche pour démarrer
un lavage. Une fois le cycle lancé, le voyant passe à
l’allumage fixe. Pour activer une pause de lavage, appuyer
à nouveau sur la touche ; le voyant passe à l’orange et se
met à clignoter. Si le symbole n’est pas allumé, il est
possible d’ouvrir le hublot. Pour faire redémarrer le lavage
exactement à l’endroit de l’arrêt, appuyer une nouvelle fois
sur la touche.
Touche VERROU ENFANT: pour activer le verrouillage
des commandes, garder la touche enfoncée pendant
environ 2 secondes. Le symbole allumé indique que
le bandeau de commandes est verrouillé. Ceci permet
d’éviter toute modification involontaire des programmes,
surtout s’il y a des enfants à la maison. Pour désactiver le
verrouillage des commandes, garder la touche enfoncée
pendant environ 2 secondes.
Stand-by
Ce lavante-séchante , conformément aux nouvelles
normes en vigueur dans le domaine de l’économie
d’énergie, est équipée d’un système d’extinction
automatique (veille) activé après 30 environ minutes
d’inutilisation. Appuyez brièvement sur la touche ON-OFF
et attendre que la machine soit réactivée.
Consommation en off-mode : 0,5 W
Consommation en Left-on : 8 W
Touche
VERROU
ENFANT
Touche
INTENSITE
DE LAVAGE
Touche
S
ÉCHAGE
FR
19
Ecran
L’écran est utile pour programmer la machine et fournit de multiples renseignements.
La section A affiche la durée des différents programmes disponibles et, une fois le cycle lancé, le temps restant jusqu’à la fin
du programme (l’écran affiche la durée maximale du cycle sélectionné, cette dernière pourra diminuer au bout de quelques
minutes car la durée effective du programme varie selon la charge de linge et les sélections effectuées); si un DÉPART
DIFFÉRÉ a été sélectionné, le temps restant avant le démarrage du programme sélectionné est affiché.
De plus, une pression sur la touche correspondante permet en outre d’afficher les valeurs maximales de température, de
vitesse d’essorage ou du type de séchage prévus pour le programme sélectionné ou pour les derniers sélectionnés s’ils sont
compatibles avec le programme choisi
La section B affiche les “phases de lavage” prévues pour le cycle sélectionné et, une fois le programme lancé, la “phase de
lavage” en cours :
Lavage
Rinçage
Essorage/Vidange
Séchage
La section C contient, en partant de gauche, les icônes correspondant à la “température”, à “l’essorage” et au “séchage”.
Les barres “température” indiquent le niveau de température correspondant au niveau maximum programmable pour
le cycle sélectionné.
Les barres “essorage” indiquent le niveau d’essorage correspondant au niveau maximum programmable pour le cycle
sélectionné.
Le symbole s’allume pendant le réglage du séchage.
Voyant HUBLOT VERROUILLÉ
Le symbole allumé indique que le hublot est verrouillé. Pour éviter d’abîmer l’appareil, attendre que le symbole s’éteigne
avant d’ouvrir le hublot.
Pour ouvrir la porte tandis qu’un cycle est en cours, appuyer sur la touche START/PAUSE; si le symbole HUBLOT
VERROUILLÉ est éteint, on peut ouvrir le hublot.
B
C
A
20
FR
Comment effectuer un cycle de
lavage ou un séchage
1. METTRE L’APPAREIL SOUS TENSION. Appuyer sur
la touche ; le voyant de START/PAUSE passe au vert et
clignote lentement.
2. CHARGER LE LINGE. Ouvrir la porte hublot. Charger le linge
en faisant attention à ne pas passer la quanti indiqe dans
le tableau des programmes de la page suivante.
3. DOSER LE PRODUIT LESSIVIEL. Sortir le tiroir et placer le
produit lessiviel dans les bacs correspondants comme indiqué
au paragrapheProduits lessiviels et linge”.
4. FERMER LE HUBLOT.
5. CHOISIR LE PROGRAMME. Sélectionner à l’aide
du bouton PROGRAMMES le programme voulu; une
température et une vitesse d’essorage pouvant être
modifiées sont associées à ce dernier. La durée du cycle
s’affiche sur l’écran.
6. PERSONNALISER LE CYCLE DE LAVAGE. Appuyer
sur les touches correspondantes :
Modifier la température et/ou l’essorage. L’appareil
affiche automatiquement la température et l’essorage
maximum prévus pour le programme sélectionné ou ceux
qui ont été sélectionnés en dernier s’ils sont compatibles
avec le programme choisi. Par pression sur la touche on
peut diminuer progressivement la température de lavage
jusqu’à un lavage à froid OFF”. Par pression sur la touche
on peut diminuer progressivement la vitesse d’essorage
jusqu’à sa suppression totale “OFF”. Une autre pression sur
les touches ramènera les valeurs aux maximales prévues.
! Exception: lors de la sélection du programme 4 la
température peut être augmentée jusqu’à 90° (+ Prélavage).
Sélectionner le séchage
A la première pression sur la touche , l’appareil
sélectionne automatiquement le niveau de séchage
maximum compatible avec le programme sélectionné. Les
pressions successives font diminuer le niveau et ensuite le
temps de séchage jusqu’à sa suppression “OFF”.
Deux types de séchage sont disponibles:.
A - En fonction du degré d’humidité du linge:
Prêt a repasser (A1): linge légèrement humide, facile à
repasser.
Sur cintre (A2): idéal pour le linge n’exigeant pas de
séchage complet.
Prêt a ranger (A3): conseillé pour le linge à ranger dans
l’armoire sans repassage.
Intensif (A4): conseillé pour le linge exigeant un séchage
complet, serviettes éponge et peignoirs par exemple.
B - En fonction du temps: de 30 à 180 min
Si, exceptionnellement, la charge de linge à laver et faire sécher
dépasse la charge maximum pvue, proder au lavage et
une fois le programme termi, parer le linge dont une partie
sera replacée dans le tambour. Suivre à psent les instructions
pour procéder au Séchage seulement. Procéder de me
pour le linge restant. Un cycle de refroidissement est toujours
pvu quand le chage est terminé.
Séchage seulement
Sélectionner à l’aide du bouton programmes un séchage
(12-13-14) en fonction du type de tissu. Possibilité de
sélectionner le niveau ou le temps de séchage souhaité à
l’aide de la touche SÉCHAGE .
En cas de sélection à l’aide du bouton programmes du
séchage coton et en appuyant sur la touche « Eco », un
séchage automatique aura lieu. Ce dernier permet de
faire des économies d’énergie grâce à une combinaison
optimale entre température de l’air et durée du cycle;
affichage sur l’écran du niveau de séchage “A2”.
Programmer l’intensité de lavage désirée.
L’option permet d’optimiser le lavage selon le degré de
salissure des tissus et l’intensité de lavage désirée.
Sélectionner le programme de lavage, le cycle se place
automatiquement sur le niveau «Normal» optimisé
pour du linge moyennement sale, (cette sélection
n’est pas acceptée pour le cycle «Laine», qui se règle
automatiquement sur le niveau «Délicat»).
Pour du linge très sale, appuyer sur la touche jusqu’à ce que
le niveau «Intensif» soit atteint. Ce niveau permet d’obtenir un
lavage très performant car l’utilisation dune plus grande quantité
d’eau au cours de la phase initiale du cycle et un brassage
mécanique plus intense permettent d’éliminer les taches les plus
difficiles; possibilité d’utilisation avec ou sans eau de Javel.
Pour traiter le linge avec de l’eau de Javel, ajouter le bac
supplémentaire 4 fourni avec l’appareil à l’intérieur du bac 1. Au
moment de verser l’eau de Javel, attention à ne pas dépasser
le niveau «max» indiq sur le pivot central (voir figure page 22).
Pour du linge peu sale ou pour un traitement plus délicat des
tissus, appuyer sur la touche jusqu’à ce que le niveau
«Délicat» soit atteint. Ce cycle réduira le brassage mécanique
pour assurer dessultats de lavage parfaits du linge délicat.
Modifier les caractéristiques du cycle.
Appuyer sur la touche pour activer l’option ; le voyant
correspondant à la touche s’allume.
Appuyer une nouvelle fois sur la touche pour désactiver
l’option; le voyant s’éteint.
! Si l’optionlectionnée est incompatible avec le programme
lectionné, le voyant se met à clignoter et l’option n’est pas
activée.
! Si l’optionlectionnée n’est pas compatible avec une autre
lectionnée précédemment, le voyant correspondant à la
première fonction sélectionnée se met à clignoter et seule la
deuxième est activée, le voyant de l’option activée s’éclaire.
! Les options permettent de modifier le chargement
conseillé et/ou la durée du cycle de lavage.
7. DEMARRER LE PROGRAMME. Appuyer sur la touche
START/PAUSE. Le voyant correspondant s’allume en vert fixe
et le hublot est verrouil(symbole HUBLOT VERROUILLÉ
allumé). Pendant le lavage, le nom de la phase en cours
s’affiche à l’écran. Pour modifier un programme lorsqu’un
cycle est en cours, mettre le lavante-séchante en pause
en appuyant sur la touche START/PAUSE (le voyant START/
PAUSE passe à l’orange et clignote lentement); sélectionner
le cyclesiet appuyer de nouveau sur la touche START/
PAUSE. Pour ouvrir la porte tandis qu’un cycle est en cours,
appuyer sur la touche START/PAUSE; si le symbole HUBLOT
VERROUIL est éteint, on peut ouvrir le hublot. Pour
faire redémarrer le programme exactement à l’endroit de
l’arrêt, appuyer une nouvelle fois sur la touche START/PAUSE.
8. FIN DU PROGRAMME. Elle est signalée par l’inscription
END” qui s’affiche à l’écran ; quand le symbole HUBLOT
VERROUILLÉ s’éteint, on peut ouvrir le hublot. Ouvrir le
hublot, vider le lavante-séchante et éteindre l’appareil.
! Une pression prolongée sur la touche permet d’annuler un
cycle déjà lancé. Le cycle est interrompu et l’appareil s’éteint.
1 / 1

Ariston FDG 9620BS EX Mode d'emploi

Catégorie
Machines à laver
Taper
Mode d'emploi

dans d''autres langues